Search Documents

By Matters C. W

THE following paper embodies the present practice and the results of past experience in the survey departments of two of the leading Broken Hill mines, the Central (Sulphide Corporation Ltd.) and the Broken Hill South S. M. Co. N. L.The authors intend to limit the scope of this paper to a consideration of office methods, as much has recently appeared in technical literature concerning field work, both surface and underground. Special reference may here be made to a valuable paper on 'Mine Surveying' by H W Gartrell, in Vol XIII of Transactions, in which the author gives considerable attention to field work. Moreover, much of the office work described in current literature is American, and sometimes not suited to local conditions, being ·often exceedingly elaborate and demanding a large staff of assistants. It is believed that the methods of recording information described in this paper are sufficiently simple and flexible to be adapted to most Australian mines. Brief acknowledgement must be made to the work done by Americans, who have raised mine surveying to the position of a separate profession, instead of being merely an unimportant branch of land surveying.

Jan 1, 1912

By Clive Chadbourne

Investigations of world wide coal face strata control practice, the study of theoretical calculations and detailed engineering analysis have been combined to design and select a powered roof support suitable for use in conjunction with the extraction of 4.5-m (14.7- ft) of the 7.5-m (24.6-ft) thick Warwickshire Thick Coal Seam. The interface between geotechnical criteria and engineering design has been closely considered along with the following 3 important factors: Firstly, the need to further improve strata control and operational characteristics whilst producing a wall integrated overall face design. Secondly, to enable the supports to be rapidly transported from face to face in roadways driven at the minimum size for operational requirements. Finally, to provide hydraulic power, automatic control and monitoring systems which will improve operations reduce manpower requirements and improve management information. Clear design requirements were determined in order to allow selection on a commercial basis. A method of tendering is described with the subsequent analysis and selection process. In the event oversupply of coal in the UK resulted in the order not being placed. Brief consideration has been given to supports suitable for reserves to be mined In a few year's time where there is potential for extraction well in excess of 4.5-m (1 4.74.

Jan 1, 1994

By Ian Misich

Surface subsidence resulting from "total extraction" of coal in the Collie Basin first occured in 1987 when Western Collieries Ltd trialed the Wongawilli mining method. Because very little quantitative subsidence data existed for the weak, Permian sediments, a research program was set up prior to the extraction of the first panel. The objective of the study was to be able to predict subsidence characteristics and effects prior to mining future total extraction panels. Attempts at predicting subsidence began using existing subsidence models from other coal mining regions, however, as more site information became available, it became clear that it was necessary to develop a separate, site specific predictive model for the Collie Coal Basin. Analysis of extensive field monitoring data for both surface and subsurface subsidence has produced a series of empirical models which can predict the shape of surface subsidence troughs and corresponding tills, and strains for rectangular panels and describe the sequences of ground movement from the mine root through to the ground surface. The fact that both subsurface and surface subsidence characteristics have tied in well, gives greater confidence for predictions made from these models

Jan 1, 1992

By M. Keen

The backfill system at Cleveland Potash?s Boulby Mine places waste filter cake underground in the form of a high concentration slurry in worked out areas of the mine reducing the mine?s environmental impact. The backfill system delivers slurry approximately 1100 m down the mine and up to 11 000 m horizontally underground. The Boulby backfill system is unique in that the placed backfill waste is not used for the usual purposes such as support, pillar extraction or reducing ventilation requirements. It was specifically implemented for environmental reasons. This influenced the design and resulted in some unique features of the system. A previous paper (Wilkins et al., 2004) described the design and commissioning of the backfill system. This paper describes the operational experience with the backfill system and backfill placement since commissioning in May 2003 and looks at lessons that can be applied in other backfill designs.

May 1, 2007

By Pierre Rocque

The Red Lake Mine is located approximately 600 km northwest of Thunder Bay. This 545 tpd (600 tons/day) underground narrow vein gold operation is set to produce in excess of 14.8 tonnes (475,000 ounces) in 2001 at a cash operating cost below 75 U$/oz. The high-grade nature of this deposit (>55 g/t or >1.6 opt) coupled with its complex geological environment and relatively deep location dictated the choice of a very selective primary mining method, Mechanized Overhand Cut and Fill. In addition to geological challenges, mine design issues such as material handling, ground stability and requirements for yieldable ground support are also discussed in this paper.

Oct 1, 2001

By J. Evans

Including: Tailings thickeners, CCD?s, paste thickeners, HI-rate thickeners, lamella thickeners, high compression thickeners, clarifiers etc. Flocculant dosing control for mining thickeners and clarifiers is influenced by a number of process factors. 1. Flow rate into the thickener or clarifier a) As the flow rate increases into the thickener or clarifier ?retention time? decreases which causes a greater affect hydraulically on the settling solids. So as the flow rate increases it will generally mean an increase in flocculant dosing rate. b) As the flow rate decreases into the thickener or clarifier the retention time increases which reduces the hydraulic affect on settling, improving settling rates. This will generally mean that as the flow rate decreases, we will decrease the flocculant dose rate.

Jan 1, 2011

CENTRAL mine ore consists mainly of galena and marmatite in a siliceous and rhodonitic gangue, the average assay values being approximately 11.5 oz. per ton Ag, 14.5% Pb, 14.5% Zn, 1.3% Ox Pb, 0.3% Ox Zn.Owing to the 1923 fire in the underground workings, much of the ore now being mined has been subjected to a certain amount of oxidation, as shown by the oxidised values above.This factor is of great importance from a flotation point of view, as a sulphide surface which has been subjected to the influence of oxidation is not as amenable to flotation concentration as a fresh sulphide surface. The importance of this factor is increased when a differential flotation is to be made, and, as in the case of Central mine ore, the sulphide, which is to be floated first, has been oxidised...

Jan 1, 1931

By John Folinsbee, Brian Danyliw, Tony Y. Chong

"Control of fugitive dust has become increasingly important in the mining industry both from a health and safety and environmental standpoint. Mining operations in particular have required improved fugitive dust control due to recent lowering of the allowable airborne silica concentration to which workers can be exposed. Experience has now proven that the implementation of a surfactant based chemical dust suppression system can enhance existing mechanical dust control methods resulting in much more efficient control of fugitive dust.The Porcupine Joint Venture (Dome Mine) utilizes dry secondary crushing and screening that makes it particularly prone to fugitive dust emissions. A variety of potential dust control systems were evaluated and this led to the installation of a surfactant based water spray system to augment the existing mechanical dust collection systems.A great deal was learned through the implementation of this system. This paper describes the entire process, from testing, system design and installation, through optimization and standardization of operation. In addition a variety of problems were identified, and innovative solutions were provided. Also, the metallurgical impacts on down stream processing are highlighted. Finally, a full discussion of overall results including a discussion of the relationship between silica and total dust concentrations is included."

Jan 1, 2005

By P. T. Allsman

INTRODUCTION The honor of being the recipient of the Mining Society's Daniel C. Jackling Award for 1966 imposes on me the responsibility to search for the subject that I would be best qualified to discuss. It seems that my experience in the mineral industry — nearly 15 years in private and 30 years in public employment — should uniquely qualify me to comment upon the relationships between the mining industry, mineral engineering as a profession, and government, and the changing economic, technologic, political and social changes that dictate their relationships. Such conditions, the increasing knowledge of the world mineral resource base, the greater demands of an expanding population with a rising standard of living, shall be evaluated with respect to our profession — mineral engineering. In all of these forty or so years, I have been in close touch with many phases of the mineral and energy resource industries, especially those of the United States. Particularly during the past 10 years, I have had a ringside seat at the "goings on" in Washington. During all of this period I have observed and analyzed many of the problems of the industry and its relations with the government. During the past few years, I have had increased opportunity for doing research and have found a need to learn something about the mathematical techniques that are undergoing such a revival since electronic computers were developed. One of these techniques is multivariate analysis, which is a system for correlating a large number of complex variables. By applying this technique to the seemingly chaotic present-day situation, there emerges a course of steady improvement in the minerals resource industries that wars, depressions, and political strife have failed to obstruct for long. In short, I advocate a need for new concepts in mineral engineering to cope with the changes, pos- sibly adding many more specialized areas on one end of the spectrum, and broad engineer-generalist approaches at the other. The meeting place shall be where the intricate mineral resource problems at the frontier of knowledge merge into the socio-techno-logical problems of the world. HISTORICAL INVOLVEMENT OF GOVERNMENT IN MINERAL RESOURCE PROBLEMS Involvement of government in mineral resource problems undoubtedly is as old as government itself. But passage of the Mining Act of 1866, superseded by the Act of 1872, was the first major entry of our Federal Government into the problems of mining. Passage of the law was necessary to resolve many conflicting claims and disputes in mining. The General Mining Law of 1872 and the Mineral Leasing Laws of 1920 apply to millions of acres of public lands and to certain privately owned land on which the mineral rights have been reserved to the Federal Government. The extensive involvement of government in the mineral industry business today often comes as a shock to the mineral engineer who has begun to climb the ladder to the top in his company. He is often poorly prepared to cope with the situation and becomes frustrated and even hostile. Better knowledge of the role of government perhaps would ease his situation. In our political system, private industry is responsible for producing minerals. To make certain that the production is adequate for a peace-time economy, and to guarantee the Nation's security in an emergency, the Federal Government finds it expedient to develop policy and engage in regulatory, educational, and research activities. A few examples will illustrate the varied role of government in relation to mineral problems. In varying degrees many agencies of the Executive Branch of Government have responsibilities that influence the functioning of the mineral and energy industries. In addition, of course, Congress, the Judiciary, and State and local governments exercise great influence. The Department of the Interior is primarily responsible for activities to promote the development and conservation of mineral and fuel resources, and the

Jan 1, 1967

By R. L. Castro

Block caving methods, when operated under favourable rock mass conditions, can achieve higher production rates and lower operating costs than other various existing underground mining applications. For this reason, it has been considered the preferred method for the mining of deep and large orebodies in current and future operations around the world. One of the key aspects in the design of block caves is the selection of the production level layout, which, among other parameters, is based on the gravity flow characteristics of the caved rock. This is because gravity flow has a large impact on total ore recovery and the amount of dilution in a caving operation. Today, there are a number of computer based methods which aim to emulate the gravity flow pattern of the caved rock. In this paper, the authors present the development of FlowSiman improved model of gravity flow based on the cellular automaton approach, to estimate dilution entry, mixing and ore recovery. As part of the model development, flow simulations were conducted and subsequently compared to full-scale data collected at two mine sectors operated by Codelco Chile. The results indicate that by using proper calibrated parameters, good correlations between simulated and measured grades as well as dilution entry are obtained. The potential use of the numerical tool to evaluate drawpoint spacing in terms of recovery and dilution for block/panel caving operations is also presented.

Jan 1, 2009

By R. Frank Chiappetta

A new blasting technique has been developed by International Technologies, LLC. to eliminate subgrade drilling, lower ground vibrations, improve fragmentation and reduce explosive consumption. The new technique utilizes a uniquely designed borehole plug, with a bottom hole air deck and a predetermined stemming mass on top of the plug. This combination is referred to as the Power Deck?. Single holes and full scale tests were conducted by Blasting Analysis International, Inc. (BAI) to determine how the system works, the mechanisms behind its success and the best design parameters to use for the given rock conditions. Results have shown reduced or eliminated subgrade drilling, ground vibration reductions of up to 33%, reduced explosive consumption by 16 to 25%, and improved fragmentation by up to 25%. This paper summarizes the methodology, field test setups, analyzes procedures and results for one series of single hole and full-scale tests which were performed in a Pennsylvania, USA quarry.

Jan 1, 2004

By T C. Ooi, L Lu

Owing to ongoing development of new orebodies and changes to existing mining operations, new ore types with distinct mineralogy, porosity and textures are generated as feed for iron and steelmaking. Moreover, further product differentiation occurs as fine ores are increasingly beneficiated to achieve grade. A study was necessary to characterise a suite of iron ore fines in terms of their propensity for formation of quasi-particles and green bed permeability prior to sintering. In this study, two Marra Mamba bedded iron deposit (BID) samples, one Pisolitic channel iron deposit (CID) samples, two dense hematite samples (coarse and fine grained microplaty hematite), one hematite-goethite BID samples and one hematite-goethite bedded/detrital iron deposit (BID-DID) composite sample were investigated. Both Marra Mamba fines and Pisolitic fines exhibit the highest green bed permeability followed closely by hematite-goethite fines, fine microplaty hematite fines, hematite-goethite BID-DID composite fines and coarse microplaty hematite fines at a moderate sintering bed depth of 500 mm. While porous fines generally form better quasi-particles upon granulation than dense fines, the amount of moisture addition increased due to the moisture saturation of the porous fines. As sinter strands become ever larger and deeper, it was necessary to examine the granulation performance of these ore types at a range of bed depths ranging from 300 to 900 mm. On average, the green bed permeability achieved by different ore types, decreased by approximately 7.5 - 9 Japanese Permeability Unit (JPU) as the bed height was increased from 500 mm to 900 mm. In order mitigate the effect of lower bed permeability of the deeper beds, small additions of hydrated lime were investigated as a binding agent to facilitate the formation of strong micro-pellets. With the addition of three per cent hydrated lime, equivalent to approximately 2.3 per cent burnt lime, the majority of fines achieved adequate permeability for deeper bed sintering, with the exception of coarse microplaty hematite fines. In simulated coastal steelmaking sinter blends, it was found that the overall granulation performance of the blend is contributed to by individual fines constituting the blend. Therefore fines possessing favourable granulating properties impart better granulation to the blend as a whole.CITATION:Ooi, T C and Lu, L, 2013. Effects of ore type and binder addition on the formation of quasi-particles and green bed permeability at different sintering bed depths, in Proceedings Iron Ore 2013 , pp 459-466 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By W. M. Myers

Jet is a substance of organic origin and has been defined by the U. S. Geological Survey as a "dense black lignite, taking a good polish, and sometimes used for jewelry". Jet is characterized by the lustrous, intense black surface it displays when polished. It is due to this property that the expression "jet black" is so commonly used to imply intense blackness.

Jan 1, 1923

By W. G. Huang

To recover the coal resources of high-sulphur anthracite in Jincheng Mining Area, underground coal gasification (UCG) of No. 15 seam in Fenghuangshan Coal Mine was proposed. The feasibility of the project was confirmed by investigations of occurrence conditions, coal properties, and roof conditions, as well as experimental studies and theoretical analysis. It was found that UCG technology is appropriate to be adopted in the mining of the No. 15 seam, due to the stable rock conditions, simple geological structure and hydrogeology, the high carbon content of the coal, non-cohesiveness, medium-thermal stability, high ash fusion temperature, and weak reactivity with CO2. Further factors are the characteristics of the immediate roof, which consists of 9.11 m of limestone and mudstone with a compact structure and low permeability, and 4.27 m of dominantly mudstone with low permeability.

Jan 1, 2012

By Walker G. S

A study of the crystalline materials on or near the surface of freshly made or "green" superphosphate granules and mature, "set" superphosphate granules was undertaken using X-ray diffraction, X-ray mapping, scanning electron microscopy and electron probe micro analysis techniques. Calcium sulphate (CaSO4), calcium sulphate hemihydrate (CaSO4 1/2H20), and mono calcium phosphate monohydrate (Ca(H2PO4)2H2O), were the only crystalline species present in the "green" superphosphate.In the set superphosphate however, additional compounds were present, namely complex iron and aluminium phosphates Ca(Fe,AI) H(HPO4hF2)2H2O, (Fe)3(H3O)H8 (PO4)6H2O and calcium sulphate dihydrate (CaSO4.2H2O).The complex phosphates tied up the major part of the Fe and Al in the system and were concentrated on or near the surface of the granule. An intimate mixture of CaSO4.2H2O, and CaSO4, along with the above mentioned complex Fe-AI compounds, crystallize close to the surface of the granule and cause the setting of superphosphate that takes place during storage.

Jan 1, 1980

The paper discusses the special mixing requirements for Metallurgical Plant Design and outlines the problems associated with the agitation in Mineral Processing Industry today. It also covers new applications such as state of the art large leach tanks and backfill for deep mining.

Jan 1, 2004

By Robert Stefanko

With passage of the Clean Streams Act of the Commonwealth of Pennsylvania and its impact on the coal industry, considerable research has been conducted to explore various approaches to the problem, including deep-well disposal. Available drillhole data from gas and oil wells were used to develop cross -sectional maps for various portions of the state and potential disposal zones were evaluated. Bethlehem Mines Corp., faced with a severe water problem at its Marianna operation in Washington County, cooperated with the Dept. of Mining at The Pennsylvania State University in establishing a 1500-ft well into the Salt Sands for the purpose of determining the feasibility of mine water disposal. The thickness, porosity, and permeability of the formation at the well site proved to be below what had been anticipated from drillhole data. Further, subsequent hydraulic fracturing did not improve the flow characteristics of the well; pumping pressures remained in the range of 1800-2000 psig for disposing of water at the rate of 150 gpm. The legal problems of disposal at the site were very formidable. When the Salt Sands proved to be less than satisfactory, permission could not be obtained to dispose in other promising formations. The paper details many of the problems associated with the experimental well and makes an assessment of the potential for deep-well disposal of mine water. The concept of disposing of liquid industrial wastes by deep-well injection is not a new one. Brines associated with crude oil long have been disposed of in this manner, with the additional benefit of aiding secondary oil recovery. More recently, with the expansion of nuclear energy, the lethal, highly radioactive wastes which are by-products of the fission process have created severe disposal problems. During the past ten years, a variety of industries have resorted to subsurface disposal, some of the details of which are given e1sewhere.l,2 The list reveals wide variations in injection rate, pumping pressure, cost, and waste disposition. Included are successful installations in Western Pennsylvania. Enactment of more restrictive clean-water legislation in Pennsylvania recently had a great impact on the coal industry. Among its provisions was the reclassifica-tion of most mine water as industrial waste whose dis-posal is prohibited in any stream of the Commonwealth. This had the effect of accelerating research in a variety of areas, although treatment methods still retained primary interest. When a feasibility study of deep-well disposal was proposed to the Pennsylvania Dept. of Mines and Mineral Industries, the Coal Research Board (CRB) approved it. This paper summarizes the efforts on this project. Acid mine water is a chemically complex liquid. having no definite quantitative relationship among its constituents. However, it is the iron disulfide (FeS2) associated with practically all coal seams that produces the objectionable products present in acid mine water when combined with air and water. The principal contaminants are sulfuric acid (H2SO,) and ferric hydroxide (Fe(OH)2. Ferric hydroxide is a rust-colored gelatinous precipitate that coats stream bottoms and destroys aquatic life. However, other ions and bacteria are present in acid mine water in varying amounts.

Jan 1, 1971

By Charles Steed

The design of pillars in room and pillar operations is always a compromise between factor of safety and ore recovery. In actively mined and accessed areas the stability of pillars must be sufficient to support the roof, providing safe working conditions for men and equipment, while optimizing ore recovery. As a reserve is mined out, and if conditions are favourable, pillars are often removed to increase recovery. Considerations for pillar removal include value of the ore, the effect on immediate and overall mine stability and the safety of the mining operations as well as the consequence of disruption of overlying strata and surface infrastructure as the support of the pillars are removed. Many parameters influence pillar strength and the contribution of the pillar to ground support. These include seam height, seam depth, seam inclination, room span, quality of rock, time, etc.. Empirical, analytical and numerical modeling methods are commonly used to optimize pillar sizing and placement and predict influence of pillar extraction or reduction on ground stability. Practical examples for pillar design and optimization in low seam gypsum mining operations and optimizing sequencing of pillar extraction in thick seam metal mining operations are outlined.

Jan 1, 2003

By John Lindsay

"Although diamond mining is a relative newcomer to the Canadian mining industry, with the first diamond mine coming on stream in 1998, Canada is already a significant producer of high quality diamonds. This paper will review diamond production trends and highlight some of the projects currently under development, which have the potential to enhance Canada’s role as a significant diamond producer.Diamond recovery plants generally incorporate well-established mineral processing and recovery techniques, with issues such as product security, cut-off sizes, and diamond preservation becoming important considerations when developing process flowsheets. A diamond processing plant must achieve three key objectives, namely:• Liberation of the diamonds from the host rock;• Separation of the heavy minerals, which include the diamonds, from the host rock;• Recovery of the diamonds from the heavy mineral concentrates.Processing technologies and equipment commonly utilized in diamond processing plants will be reviewed and some of the significant issues associated with each option briefly discussed.Typical process flowsheets will be presented.Finally, an overview of De Beers’ Victor diamond project, located in northern Ontario, will be provided. This potentially significant diamond producer is currently at a pre-feasibility stage of development.DIAMONDS IN CANADAWorld Diamond ProductionCommercial diamond mining commenced in earnest with the discovery of the Kimberley diamondfields in South Africa in the late 1800s, and this resulted in a dramatic increase in the supply of diamonds. As can be seen from figure 1, world diamond production, mainly from South Africa, Angola, Congo, and Namibia, remained relatively constant through the early 1900s until the development of the large Russian kimberlite pipes in the 1950s. Production increased again in the 1960s and 70s with the development of the Botswana mines, but the most significant increase in global production came from the Argyle mine in Australia, which came on stream in 1983 and produced a peak of almost 43 million carats in 1994, representing approximately 40% of the world market. Production from Argyle has since fallen-off as grades have declined and the strip ratio has increased with the deepening of the open pit."

Jan 1, 2003

By A. W. Khair

This paper deals with the design characteristics of cutting tools and the operating parameters these tools are usually subjected to. Eight types of cutting tools/bits with different geometrical shapes and sizes were tested in a linear cutting apparatus, utilizing concrete blocks. The objectives of these experiments were to study the performance of each type of bit, make qualitative assessment of each bit geometry and size and establish cutting parameters for efficient utilization of the tools. During the experiment required forces Fx, Fy, and Fz, cutting, penetrating and lateral forces respectively and audible and sub-audible noises were measured. In these experiments, the depth of cut was kept constant to 1.5 inch while the bit spacing was varied 1.5,2.25 and 3.0 inch (3.75,5.6 and 7.5cm respectively). The results of these experiments indicated that by optimum ratio of depth of cut to bit spacing, the cutting face will be cleaned with the least ridge/land remains between the bit groves, resulting in least specific energy consumption, more large and less fine product particles and substantial reduction of audible noise. The results of these experiments also showed that proper bit design not only decreased cutting energy consumption but also reduced audible noise.

Jan 1, 2001