Search Documents

By Bruno Alves Resende, Antonio Adel dos Santos

Temperature, microstructure and dimensions are the main material parameters to be controlled during hot rolling of steel. Although thermal mathematical models have long been developed and applied for hot strip rolling, each Hot Strip Mill (HSM) must have its own model adapted to its facilities. Thus, a mathematical model for temperature evolution during rough rolling has been developed for the Usiminas HSM at Ipatinga Plant. The model achieved a high level of accuracy, which was assessed by comparing measured values of temperature at the hot strip mill entry with the calculated ones, the difference ranging from 9°C to 17°C. Application examples have shown that the slab can be occasionally stopped before start of rolling for as long as a couple of minutes without compromising its further processing. On the other hand, if the transfer bar stops after rough rolling even for short time, further processing in the HSM can be hindered, due to excessive temperature drop. In case of such abnormal line stop, the model can be used as a tool for decision-making to either continuing the planned rolling schedule or to changing the route, thus improving the overall rolling process.

Oct 1, 2019

By Hervé Thomasson

Siemens VAI has made an important Research & Development effort since 10 years on laser welder field. The last step of this program was in 2010, the evolution of its laser welder range by implementing the solid state technology with laser cutting and welding. Since this step, 8 welders were produced by Siemens VAI. Now after more than 1 year of industrial feedback, the results are showing a high level of performances on very demanding processing lines for a large range of products from Silicon steel to High Strength Steel with DP and TRIP grades. This laser welder concept using laser cutting and welding through solid state laser source is also proposed by Siemens VAI for pickling lines and tandem mills with significant advantages compared to standard solution.

Jul 30, 2018

By Nigel Marx

In order to understand (and ultimately to predict) the friction reduction resulting from the use of polymer solutions, the rheological properties of model polymer solutions have been measured over a wide range of shear rates. Both temporary and permanent shear thinning have been observed. By using base fluids of different viscosities it has been shown that permanent shear thinning depends more closely on the shear stress experienced by the fluid than on the strain rate. Hydrodynamic measurements have been made on the polymer solutions using a compliant ball on flat lubricated contact that operates in isoviscous-elastic conditions. The measured friction values can only be predicted with reasonable accuracy if the measured shear thinning properties of the lubricant are taken into account in the hydrodynamic model.

Jul 31, 2018

By Filippo Verlezza

Conventional wire rod blocks have some limitations. They can only roll with fixed reduction ratios which always require the same rolling diameters within the block. With MEERdrive® SMS, as a pioneer, has introduced an innovative drive concept for wire rod blocks that can overcome the limitations of conventional solutions. The clue: the concept is based on individual drives for each stand position. The exigent wire rod market demand and the available technology melt in a new variant of MEERdrive®, the MEERdrive®PLUS, which represents a sizing block solution for finished size rolling and allows conventional as well as thermomechanical rolling. Further “one family rolling” is also possible, since all roll / size changes will occur in this block.

Oct 30, 2017

By Wilian da Silva Labiapari

Austenitic stainless steels are widely known for their good weldability, excellent mechanical properties for deep drawing and superior corrosion resistance in environments where most of the metals fail. Their uses include many applications subjected to a combination of mechanical and corrosive wear, such as pumps, valves and surgical implants. Although their corrosion resistance has been largely investigated, their resistance to mechanical wear is less studied. In particular, their performance under conditions involving combined corrosive and mechanical wear is not well understood. The aim of this study is to demonstrate the effect of the mechanical component on the electrochemical signal of an anodic polarization curve. A test rig was developed to investigate micro-abrasion-corrosion using a fixed ball configuration. Tests were carried out using stainless steel AISI 304 samples and 25.4 mm zirconia balls as counter bodies. The electrolyte was a 1N H2SO4 solution with SiO2 as abrasive dispersed at the concentration of 10 wt%. The results showed an increase in current density when the counter face roughness and the normal load applied during the tests are increased, evidencing a mechanical influence on the surface activity of this material in a corrosive environment.

Jul 31, 2018

By Uazir Bezerra de Oliveira, Günther Staudinger, Michael Skorianz, Edo Engel

Oct 1, 2019

By Cameron Soltys, Hamid Ghorbani, Maher Al-Dojayli

Cooling staves in blast furnaces are used to minimize the process heat loads on steel shell and refractory system. Copper staves are exposed to significant fluctuating thermal loads which may lead to premature stave failures due to cracks, water leakage, bending, abrasion and resultant wear. In this paper, an assessment methodology is presented to evaluate the effect of thermal cycling on copper staves including bending, fatigue and thermal ratcheting. This approach incorporates temperature-dependent copper properties including creep and plasticity to more accurately capture inelastic deformations, damage and fatigue in staves under transient and cyclic thermal loading conditions. Root cause failure assessment and improvements to copper stave design can be assessed using the presented methodology.

Oct 1, 2019

By Nicola Santangelo

The current economic crisis and growing environmental issues have led the steel industry to face the simultaneous effects of low demand and production overcapacity in a globalized steel market, whilst confronting high energy prices and the need to comply with the green economy. Heat Recovery from waste gas of the Electric Arc Furnace (EAF) represents one of the greatest opportunities to reduce the consumption of primary energy and reduce the CO2 emissions in steel industry. The heat of the off-gas, if recovered and converted into electrical power, can make the whole Fumes Treatment Plant autonomous from the electric point of view, thus making it a “Zero-Energy FTP”. The concept is to substitute the Cooling Components (Water Cooled Panels and Air Cooler) are substituted with Heat Recovery Components (Hot Water Cooled Panels and Heat Exchanger). The recovered heat can be converted into power by using an Organic Rankine Cycle (ORC) turbine. The heat recovered by the HWCP and the Heat Exchanger is characterized by a variable thermal power, which affects the efficiency of the downstream ORC System. Danieli, in collaboration with the University of Udine, has developed the Thermal Stabilizer Unit (TSU). Danieli has realized the first step towards Zero Energy FTP at ABS steelmaking plant (Italy) by installing a CHR® - Clean Heat Recovery. This plant has been started up on 17th October 2014. The HMI of the CHR® is integrated in the HMI of the furnace, so all the process could be kept under control by the furnace operator. At ABS recovered thermal power reaches 5.5 MW. The max power production reached with CHR plant in ABS (over 1MW of electric power) consents an annual saving of approx. 500,000 EUR.

Aug 16, 2017

By Luiz Henrique Accorsi Gans

First, this works carries an experimental evaluation for austempered ductile iron (ADI) as a gear material. And second, in order to provide a better understanding of the microstructural effect on the stress state of subsurface regions, a finite element method approach was considered using the submodeling tool in ANSYS 11.0. For this, ADI gears were produced from continuous cast iron bars, heat and thermochemical treated and tested in FZG test rig. The results were compared to those of carburized steel AISI 8620 and induction hardened steel AISI 4140 gears. The wear experiments were performed at the temperature of 90ºC with two torque stages: 135 N.m (running-in) and 302 N.m (steady-state). The time for pitting and spalling on the gears surfaces were measured using image analysis. The results showed a very good potential of using ADI for manufacturing gears, replacing induction hardened steels. Also, the ADI gear with smaller nodules showed higher life for pitting. In contact fatigue tests with severe load, the carburized AISI 8620 steel proved more adequate than the austempered ductile iron, showing that the mechanical properties are critical in the resistance to damage in gear contact. The austempered ductile iron with smaller nodule size showed to be very competitive with wear resistance similar to AISI 4140 steel induction hardened. With ANSYS, it was verified that the nodule size affects the gears life independently of the mechanical properties of the matrix. The results showed that the nodules indicate the presence of a concentration stress, but their size doesn’t affect the contact fatigue life as much as the total amount of nodules, regardless of the ductile iron microstructure. The size and number of nodules affects both the nucleation and the propagation stage of cracks. ADIs with higher amount of nodules have a greater wear resistance. Also, compared to the Hertz contact theory (isotropic material), the presence of graphite nodules indicates a non-isotropic material and made the maximum shear stress point moves toward the surface.

Jul 31, 2018

By Chad B. Donovan

There is a strong need in North America and other major steel producing markets where major capital investment in new equipment has been minimal over the past several years to make improvements to existing casting machines. In many cases, very cost effective improvements can be made to existing equipment in order to maximize the efficiency and production of an older designed continuous caster, a classic caster. SMS Group and its predecessor companies have been maintaining continuous casting molds for over forty years. This experience has allowed SMS Group to intimately understand the advantages and disadvantages of each design. The most vital component of the continuous caster is the mold copper design, as it has the most influence over the ability to cast a quality product. Updating to a modern copper design is less complicated than most steel producers think and the benefits are significant. Premium mold coatings such as UniGuard® and NanoGuard® allow casters to guard against exposed copper and wear while producing quality products for record campaign lengths.

Oct 30, 2017

By Aline Lima da Silva

The reduction in SOFC operating temperature due to recent development in materials and fabrication techniques enables the use of ferritic stainless steels as interconnects for SOFCs. Ferritic stainless steels offer many advantages over traditional ceramic interconnects, such as higher thermal and electronic conductivity, as well as relative ease of fabrication. However, the formation of chromium oxide on ferritic stainless steel results in an increase in ohmic resistance and can lead to the loss of cathode catalytic activity (due to Cr volatilization, with cathode poisoning). The oxide growth depends on several factors, such as steel composition, temperature, oxygen partial pressure. In this way, knowing the phase stability, the oxidation behavior of the material and the oxidation kinetics is of great interest. In this context, a thermodynamic study of the oxidation of ferritic stainless steel 430 under oxidizing atmosphere (cathode), at the temperature of 750ºC, is carried out. As one can see, the thermodynamic system can be very complex, involving several phases (chromium oxide, (Fe,Cr,Mn)3O4 Spinel, iron-chromium oxides, etc.). The effect of oxygen partial pressure and alloying elements on phase distribution is evaluated. Thermodynamic modeling is compared with experimental results from literature.

Aug 8, 2018

By Alberto Pesamosca

The present work analyzes the latest results achieved in scrap based EAFs in terms of application of chemical energy, starting from the observation that the general trend is a reduction of oxygen utilization. Consequently a review is needed about criteria for evaluation of melting process efficiency and equipment design. If from one side the maximization of productivity remains one of the major goals, from the other side some aspects of present market situation, included price of raw materials, are requiring the maximization of process yield. Based on achieved performance figures of selected plants and theoretical considerations, the effect of chemical energy input intensity is analyzed focusing on transformation cost, productivity and total energy input. The effect of present practices with lower oxygen utilization is considered also in terms of global CO2 emissions. Finally, the latest Danieli concepts and technological tools for optimization of chemical input are presented.

Aug 17, 2017

By Gabriel Oliveira Glória

Em busca de materiais ecologicamente corretos, a sociedade pode optar pelas fibras naturais na substituição das sintéticas. Uma boa opção entre as fibras naturais está a fibra de PALF, mas não há informações sobre a resistência ao impacto de compósitos de epóxi incorporadas com fibras de PALF. Portanto, o objetivo deste estudo foi investigar as propriedades mecânicas em testes izod, de compósitos epoxídicos incorporados com até 30% em volume de fibras de PALF. Os resultados demonstraram que a fibra PALF aumenta a resistência ao impacto dos compósitos poliméricos.

Aug 17, 2017

By Lorena Cristina Amorim Moura

O balanço de enxofre ao longo da cadeia de produção de aço é um problema muito discutido no setor siderúrgico, pois afeta a qualidade do produto final. Assim, este estudo tem como objetivo desenvolver uma metodologia de previsão de enxofre do coque, a partir de enxofre do carvão, com base na sua taxa de dessulfuração, obtida através do Índice de Inchamento Livre (FSI) em escala laboratorial. Estes resultados mostram boa correlação com o processo de fabricação de coque, permitindo a determinação do valor em uso em relação ao teor de S de cada carvão.

Oct 30, 2017

By Frank Schrama

Steelmakers worldwide agree that the most efficient and cost-effective solution in BOF steelmaking is to desulfurize the hot metal between the blast furnace and converter. Various methods are currently in use, among which the Kanbara Reactor (KR, using only lime as a reagent), Magnesium mono-injection (MMI, using only magnesium; also known as the Ukraina-Desmag process) and co-injection (using magnesium and lime/CaC2) are leading. These three hot metal desulfurization methods are compared based on metallurgy, efficiency, costs and overall performance. Both available data from literature and experience from Danieli Corus engineers is used for this study. The KR process is able to reach low sulfur concentrations (> 10 ppm) in hot metal and has lower reagent costs. However, due to higher Fe-loss and heavy wear the KR process has the highest operational costs. The Magnesium mono-injection process is very fast due to the use of the reactive magnesium as reagent. Major problems with resulfurization (sulfur levels below 50 ppm cannot be reached) and the violence of the process made that this process could never get a firm foothold in the western steel industry. The co-injection process with magnesium and lime proves to be able to combine the best of both worlds. It can reach low sulfur concentrations and desulfurize fast. Co-injection is also the most flexible and cost effective.

Aug 16, 2017

By Jari Larkiola, Aarne Pohjonen, Juha Jokisaari, Oskari Seppälä, Joonas Ilmola

Finite element method (FEM) is widely used to model the hot strip rolling process. Flatness defects e.g. front-end bending in multipass hot strip rolling is studied by authors using a finite element (FE) model with interactively operating automated controlling logic (ACL) [1]. However, industrial corresponding grade of accuracy in strip thickness subsequent to the rolling pass is not easily accessible in FE-model without separate calculation of significant rolling parameters and integrated roll gap control. In order to study flatness defects and optimize pass schedules the controlling and physics of the FE-model must correspond to the industrial process. For this need the automated controlling logic is upgraded by setup calculations to predicting roll force and work roll flattening. These predictions are utilized in setup positioning of a work rolls. Reliable setup calculation enables smooth multi stand rolling process without significant additional adjustment of roll gap clearance. State of art rolling technology requires above-mentioned setup controlling for the FE simulations to simulate different pass schedules without time consuming preparations. Operational setup calculations together with automated controlling logic of hot strip rolling enable simulation of new pass schedules and efficient problem solving.

Oct 1, 2019

By Jianping Li, Fei Peng, Yunbo Xu, Jiayu Li

In this study, in order to achieve ultra-high strength without reducing plasticity, a novel heat treatment involving a pre-quenching process prior to conventional intercritical annealing (P-IDP) was proposed in a low carbon low alloy DP steel. It revealed that abundant fraction of banded structure was observed after conventional intercritical heat treatment (IDP) due to the inheritance of cold rolling deformation. However, the banded structure in novel heat treatment was eliminated significantly, whilst the refined microstructure was relatively more homogeneous with ultrafine ferrite grains. Moreover, obvious chain-networked martensite grains along the ferrite grain boundaries were obtained. The optimum mechanical properties with ultimate strength of 1238 MPa, total elongation of 17%, product of strength and elongation (PSE) of 21GPa% were obtained by P-IDP treatment, which was much higher than the values reported with similar composition. As to pre-quenching treatment, all of grain refinement, homogeneous distribution of martensite islands and precipitated strengthening of microalloyed carbides were beneficial to improve the final strength and ductility.

Oct 1, 2019

By John Hinton

Electromagnetic based (EM) sensor technology has been shown to detect changes in the magnetic permeability of steel strip travelling down the run out table after rolling. Measuring below the Curie temperature, these changes can be interpreted in terms of the phase transformation from austenite (paramagnetic) to ferrite (ferromagnetic). These real time measurements provide a detailed insight into the changes in the structure at high temperature providing the steel producer with feedback on quality control, product consistency and product development. However unlike mill microstructure models, the sensor measurement provides a point reading at a distance through the cooling course. To map the transformation in more detail, a sensor array is required along the length of the Run Out Table i.e. to measure points on the austenite to ferrite transformation curve. This paper describes the process and metallurgical factors that should be considered in the optimum design of a sensor array, i.e. the number and location of the sensor heads. Examples of cooling strategies for different steel grades e.g. low carbon, structural and dual phase steels are used to demonstrate the importance of sensor location. In addition, the effect of variability within typical industrial parameters e.g. cooling speed, on the sensitivity of sensor output and location will be considered.

Oct 1, 2019

By Chad Byron Donovan

There is a strong need in North America and other major steel producing markets where major capital investment in new equipment has been minimal over the past several years to make improvements to existing casting machines. In many cases, very cost effective improvements can be made to existing equipment in order to maximize the efficiency and production of an older designed continuous caster, a classic caster. SMS Group and its predecessor companies have been maintaining continuous casting molds for over forty years. This experience has allowed SMS Group to intimately understand the advantages and disadvantages of each design. The most vital component of the continuous caster is the mold copper design, as it has the most influence over the ability to cast a quality product. Updating to a modern copper design is less complicated than most steel producers think and the benefits are significant. Premium mold coatings such as UniGuard® and NanoGuard® allow casters to guard against exposed copper and wear while producing quality products for record campaign lengths.

Aug 16, 2017

By Guilherme Liziero Ruggio da Silva

Uma marcha estável do alto-forno (AF) está ligada à consistência das propriedades químicas, físicas e metalúrgicas das suas matérias-primas (MP), especialmente, as do coque. As propriedades do coque são reflexos das propriedades dos carvões que lhe deram origem. Em termos de propriedades ligadas à natureza do carvão, a qualidade do coque é bastante influenciada pelo rank dos carvões, que compuseram sua mistura, ou seja, quantidades de macerais reativos e inertes, bem como suas propriedades coqueificantes, que é, exatamente, a habilidade inerente aos carvões aglutinantes de quando aquecido, amolecer, tornar-se plástico e solidificar em uma massa coerente. Neste contexto, o presente trabalho se propõe a evidenciar as mudanças no modelo de britagem de carvões da Gerdau Ouro Branco, bem como a operacionalização do padrão criado. Após a implantação, verificou-se a elevação de 1.8% em DI.

Aug 17, 2017