Search Documents

By Mery-Cecilia Gómez-Marroquín

O presente trabalho trata da formação da ferrita de zinco a partir da mistura e posterior reação solido-solido entre o óxido de zinco e óxido de ferro - Fe2O3 puros em proporções equimolares. A faixa de temperatura onde teve lugar a formação foi entre 1073 e 1373 K. Testes de redução da ferrita da zinco sintética-ZF e pós de aciaria elétrica–EAFD foram realizadas usando misturas de CO e CO2 que variaram entre 50 e 100% CO. Ambos os testes (formação e redução de ZF e EAFD) foram suportados usando técnicas de caracterização física, química, estrutural e microscópica. No caso da redução, foi observado que tanto a temperatura como a percentagem de CO, foram os fatores que, mais afetarem a redução de ferrita de zinco contida no EAFD. A máxima percentagem de redução da ZF foi 85%, para 100% CO, 1373K e 105 min, e 52%, para 50% CO, 1373K e 105 min. Por outro lado, atingiu o 100% para 100% CO, 1273K, em 80.75 min, 60%, para 50% CO a 1373K durante 105 min. no caso da redução do EAFD

Aug 17, 2017

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Beatriz Peralta Oruê

Manganese, a toxic mineral, related to manganism may have high added value for the steel industry. The difficulty in obtaining manganese encourages the exploration of new secondary sources such as the lateritic nickel effluent. In Brazil, nickel reserves are predominantly lateritic, making the country a potential producer. For the tests, a synthetic solution was used which simulates the lateritic nickel effluent from leaching. The oxidative precipitation with ozone occurred at the oxygen flow rates: 0.5; 1.0 and 2.5L/min, at the original pH 1.5 at 21°C in a 500 mL bubble column reactor. O3 was produced in the benchtop generator feed by 99% oxygen. The ozonation time was determined by the oxidation potential1.55V. The ozonated solution was centrifuged and filtered. The filtrate and collected samples were characterized in ICP-OES. Optimization tests with ultracentrifuge were performed. The best precipitation reached 97% at 0.5L/min O2 at 6.07 ± 0.045mg/min of O3 dosage and resulted in a solution 10-15mg/L Mn+2, above 1mg/L, maximum value acceptable by Conama 2011, to be retreated before being discharged into the water body or being reused as a manganese source.

Oct 3, 2019

By Pedro Henrique Coutinho

Este trabalho teve como objetivo a redução do custo de transformação da Aciaria de Resende (Votorantim Siderurgia), visando à redução do Cash Cost do tarugo, ponto fundamental no atual cenário econômico da siderurgia brasileira. Para priorizar as ações, otimizar recursos e tratar o tema de forma estruturada foi utilizada a metodologia DMAIC na execução deste projeto. Como resultado houve redução no custo de transformação, alcançado por melhorias nas linhas de Energia Elétrica, Ligas, Escorificantes, Eletrodos e Outras Variáveis.

Aug 16, 2017

By Sander Mul, Michael Brandner, Armin Paar

Graphitic HSS roll grades such as ESW’s brand VANIMO can be considered as the latest developments for the last finishing stands in hot strip mills. These roll grades are developed on the basis of the alloying concept of (Carbide Enhanced) Indefinite Chill work roll materials. During the development of VANIMO, the amounts and types of carbide forming elements were increased and adjusted into the direction of cast HSS roll grades. The microstructure of graphitic HSS roll grades therefore consists of tempered martensite, cementite and several different carbide types as well as a well-defined amount of free graphite. The main purpose of graphitic HSS roll grades is to combine the high surface quality of Indefinite Chill alloys as well as the high wear resistance of HSS roll grades. Several systematic steps were taken to increase the wear performance from Carbide-Enhanced Indefinite Chill grades to the more advanced VANIC grade and further on to the highest alloyed roll grade VANIMO. In every development step, the surface quality of the roll grades was carefully monitored. The decision to invest in new testing equipment at ESW’s plant was driven by the wish to see microstructural effects of different alloys in a macroscopic dimension. Usually samples are taken from cast rolls and investigation is done in comparably small areas compared to the total surface of a roll. Rolling of strip is done with the entire barrel, so effects of alloy and microstructure can appear anywhere on the barrel surface. To ensure better understanding and deeper knowledge about influences of alloying trials we decided to install the last version of LRI (Lismar Roll Inspection). LRI includes the latest technology of Eddy Current with an enormous resolution. Depending on the formation of carbide precipitations, carbide network as well as matrix and free graphite, the EC test can detect smallest differences. The possibility to analyze the different results of EC and UT surface wave inspection will be discussed. A few examples of surface effects in the mill application will be discussed and improvement strategies explained.

Oct 1, 2019

By Leonardo Pereira

Este trabalho reporta a viabilidade de realizar o tratamento térmico de austêmpera, para obtenção de um Ferro Dúctil Austemperado (ADI), utilizando uma liga de Zn-Al-Mg-Cu, como meio de resfriamento e permanência em patamar, durante o processo de tratamento térmico. Por meio da obtenção da curva de resfriamento da liga Zamac 5, constatou-se a viabilidade de realização da austêmpera em temperaturas superiores a 380ºC. A partir de corpos de prova de ferro fundido nodular de matriz predominantemente perlítica, instrumentados e austenitizados a 870°C e 900°C, avaliou-se a taxa de resfriamento promovida pela liga Zamac 5, até a temperatura de 400°C. O tratamento mostrou-se eficiente, utilizando a liga como meio de austêmpera, sendo registradas taxas de resfriamento superiores a 6°C/s. A análise morfológica constatou a formação de ausferrita, sem a presença de perlita, caracterizando assim a formação do ADI.

Oct 30, 2017

By Martin Dirks

Nowadays the sinter cooler often becomes the bottleneck of the sinter production, with outdated equipment leading to low productivity and high operation and maintenance costs. Furthermore valuable energy is simply destroyed in the cooler, which is not compatible anymore with a cost efficient and environmentally friendly sinter production. Paul Wurth has developed and improved two types of coolers, the annular cooler and the shaft cooler which offer flexible solutions to the specific situation of each client. The classic design of the annular cooler was completely revised and is now composed of a rigid ringframe construction as opposed to the traditional design with individual sintering cars, avoiding the typical problems of centering. Additional features of the PW annular cooler are the low air leakage rate and the increased effective cooling surface due to the removal of dead areas. This leads, in addition to the lower weight, to lower operating costs and a smaller space requirement. The shaft cooler stands out with an even smaller space requirement and a lower sinter outlet temperature because of a very long residence time of the sinter inside the shaft. Its development into a pure counter flow cooler aims at maximizing its energy efficiency, as it is designed as a system with a very low demand for cooling air, high air discharge temperatures and highly reduced dust emissions. For both cooler types flexible heat recovery solutions can be offered. These solutions include the supply of hot combustion air to the ignition hood burners and the sinter strand, the production of steam for the clients steam grid or the production of electric energy.

Aug 16, 2017

By Ronaldo Câmara Cozza

Iron aluminide alloy; Ball-cratering wear testing; Rolling abrasion; Wear volume; Coefficient of friction

Jul 31, 2018

By Cintia Guimarães Ferreira

O uso de materiais compósitos possibilitou relevante avanço tecnológico em áreas biomédicas e industriais. As matrizes poliméricas reforçadas por Fibra de Vidro são predominantes em nível comercial devido à facilidade no processo de fabricação. Entretanto, podem apresentar variabilidade intrínseca de propriedades devido a fatores importantes, tais como: não uniformidade e não conformidades relativas ao reforço e matriz. Inspeções visuais identificam defeitos característicos de distorção de fibras, bolhas superficiais e áreas secas de impregnação. Para detectar porosidades, trincas ou delaminações outros métodos são necessários. Este estudo apresenta a técnica de Radiografia Direta (RD) para a inspeção de materiais compósitos. Utilizou-se um detector Flat Panel do tipo silício amorfo (aSi), uma fonte de raios X de potencial constante e uma mesa controlada por Arduino. Foram realizadas radiografias de duas juntas de 4 polegadas de diâmetro nominal de material polimérico reforçado por fibra de vidro. Como resultado, foram detectados defeitos de delaminação, descolamento, trincas e porosidades, que não poderiam ser detectados visualmente.

Oct 30, 2017

By José Dimas Arruda

O conhecimento do campo de fluxo dentro do molde pode oferecer uma oportunidade de melhorar a limpidez interna do produto final. A técnica PIV foi empregada para avaliar a distribuição de velocidade longitudinal ao longo de uma ampla seção variando da válvula submersa até a face estreita de um molde de lingotamento de placas, bem como a distribuição de velocidade transversal correspondente. Estas informações podem ser utilizadas para avaliar o grau de turbulência interfacial.

Jul 30, 2018

By Renan Bueno Wojciechowski, Yukio Shigaki

The quality of flat rolling process depends highly on multiple factors such as applied forces, materials involved for both strip and rolls, roll geometry and its positioning. To calculate the strip shape, a mathematical/numerical model can be applied, showing the final product and how the equipment behaves when changing some parameters. This is usually a time-consuming task for both user and computer, especially when it involves thin and hard strips. By coupling a quick rolling load calculation method as Bland-Ford and Finite Element Method (FEM) for roll stack deformation, it is possible to create an accurate and user-friendly rolling simulator. This paper presents the improvements done in the 3D FEM/multi-slab method and its actual capabilities by simulating two cases of a 6-High rolling mill. Different analysis in this equipment can be easily done in about 10 minutes by using the developed an electronic spreadsheet program interface and the folder generated with relevant results and logs. An operation manual and a commercial FE program plugins were made to aid construction of a completely new model. The code was created in a modularized way to assist the application of this simulator for other operational conditions.

Oct 1, 2019

By Marcos Paulo da Silveira, Carolina Conter Elgert, Messias Prado de Almeida, Rafael Stella Galdino

Microalloyed steels have been intensely studied as an alternative to increase strength by grain refinement and/or precipitation hardening. Long steel products have a wide range of opportunities to apply well-defined principles of controlled rolling (CR) in order to increase strength and toughness with reduced costs. To evaluate the effect of microalloying elements as Nb and Ti with thermomechanical treatment, three conditions were tested: DIN 16MnCrS5 with hot rolling (HR), DIN 16MnCrS5 with Nb and CR and DIN 16MnCrS5 with Nb+Ti and CR. Austenitic grain size, obtained by direct quenching after rolling, has shown a decrease 32% with Nb addition, and 29% when Nb and Ti was added. Controlled rolling generated higher grain refinement and pancacked grains near the surface. When comparing ferritic grain size, controlled rolling plus niobium and titanium additions resulted in significant reduction of 35%. Yield strength increased 15% with microalloying and CR and more than 270% in impact toughness, even at -40°C.

Oct 1, 2019

By Valdicleide Silva Mello

Nowadays the biodiesel use is obligate in Brazil, in order to reduce the emissions of fuel burn. However, it is important to analyze which percentage of biodiesel is necessary to keep or improve the lubricant action of fuel for diesel engine, as well which kind of biodiesel give better performance. Therefore, this work aims to analyze the parameters that keep the lubricant action of biofuels, by using the Box-Behnken design type to optimize them. In this design was evaluated the input parameters: the type of the biodiesel (soybean, sunflower and palm), the concentration (5%, 20% and 100%) and the temperature of contact (25°C, 40°C and 60°C). The analyzed output parameters were the percentage of film formation, coefficient of friction, wear scar diameter (WSD) of ball, these output parameters were obtained by HFRR tribometer and they were analyzed applying response surface methodology. With this methodology was possible to determine the simultaneous influence and the interactions between two or more independent variables investigated. The response surfaces generated for the coefficients of friction, WSD, film formation showed a higher lubricant action for higher levels of concentration of biodiesel. An increase in lubricant action was found to high and intermediate temperature.

Jul 31, 2018

By Andrew Slifka, Pello Uranga, Douglas Glenn Stalheim

Structural steel final mechanical properties of strength and ductility are predominately generated by the final ferrite grain size/packet size and homogeneity of that ferrite grain size/packet size through the cross-sectional area. Forty to seventy percent of the strength components come from how fine the final cross-sectional ferrite grain size/packet size that can be produced.[1] All the ductility properties of structural steels for a given microstructure are predominately driven by how fine AND homogenous the final cross-sectional ferrite grain size/packet size can be refined.[2,3,4] One key ductility property of structural steels used in construction and energy transmission applications is fatigue. Both low and high cycle fatigue can be realized in these end applications, however, low cycle fatigue is typically the predominate mechanism. In construction applications the environment for fatigue is typically air, such as in wind towers or high-rise building construction. In energy applications, there is an interest in high pressure (5.5 – 21 MPa, 800-3000 psi) gaseous hydrogen as an alternative fuel source to fossil fuels. A project to study the effect of the cross-sectional grain size/homogeneity of a relatively pure polygonal ferrite microstructure on the fatigue performance in air and high-pressure gaseous hydrogen has been developed. This paper will discuss the project strategy, microstructure developed for the project and initial test results.

Oct 1, 2019

By John Malcolm Gray

Interest in X-80 linepipe steels emerged in the early 1980’s and it was first used in 1985 by Ruhr Gas [1]. The early steels were extensions of conventional Nb-V or Nb-Mo microalloyed X-70 steels but other alloying concepts emerged based on Nb-Mo-B alloying (NKSTAF [2] and ULCB [3]). The latter had acicular ferrite/bainitic microstructures and carbon contents below 0.05 percent. In parallel renewed interest developed in ultra low carbon (0.02 percent) higher niobium steels which had first been studied in 1962 [4]. Such steels exhibited excellent notch toughness when processed with high finish rolling temperatures (>950°C) which made them suitable for processing on weak, older rolling mills. With time such steels, designated “High Temperature Processed”, or HTP steels, were further optimized and produced in modern, very strong rolling mills due to their superior economy compared with traditional vanadium and molybdenum containing steels. The chronology of the HTP development is presented in the present paper. Full scale demonstration heats of a 0.06 percent carbon 0.10 percent niobium steel were produced by Bofors Steel Plant in 1972 and were converted from slabs to plates by nine different steel mills [5-7]. Commercial application in API Grade X-70 first occurred in Canada in 1974 [8,9] but the concept was only used sporadically after that until 1998 when it was applied for the API Grade X-70 Sour Service Cantarell Project [10] in Mexico. Soon thereafter, the El Paso Cheyenne Plains Project used a 0.05%C 0.095%Nb 0.27%Cr variant of the HTP steel [10-12]. Nowadays the HTP concept is being utilized for construction of approximately 6000 km of 48” OD x 18.4 mm X-80 per year in China. The metallurgical principles and history of the development are presented in details in this paper.

Aug 7, 2018

By Afonso Cardoso da Silva, Romeu Thomaz Viana Jr, Emanuelle Garcia Reis, José Herbert Dolabela da Silveira

The Gerdau Ouro Branco Mill, three years after the implementation of its new plate mill, has started to develop high complexity products. The plate mill’s learning curve has been increasingly challenging since products are being developed to their highest grades. This work aims to present the first results of the development of steels of the strength class of 510 MPa produced by TMCP (Thermomechanical Controlled Processing) followed by accelerated cooling. These results show the potential and advantage of the accelerated cooling process regarding to obtain products of high mechanical strength and high toughness, associated with a low equivalent carbon.

Oct 1, 2019

By Ernst Lindemann

The SMS group has developed the ultrasound technology “HD scan” for inspection of the internal quality of as-cast products. This method of sample analysis requires less preparation work and is safer than the current, most common technique of etching and/or sulphur printing. Furthermore, this technology offers a three-dimensional view into the sample of the cast product and thus more representative information for a better quality evaluation. The internal quality evaluation can be performed automatically and objectively by software based on clear statistical methods. A quantitative centerline segregation rating can be assigned to each sample, based on the size and distribution of segregates detected by the unit. Internal crack statistic (length, position, orientation, etc.) and narrow side profile can also be measured. Grain macrostructure can also be visualized which allows for a potential optimization of casting parameters like strand cooling, soft reduction or electromagnetic stirring. The accuracy of the new method was proven by parallel metallographic investigations of more than 100 samples of different steel grades and sample shapes. Automatic defect evaluation and classification was compared against macroetching results. It was found that HD scan identified more defects and the visualization of the macro structure could be performed in more cases than with macro etching. All tests, comparisons, further developments and analyses for various steel producers and steel treatment companies have been conducted at the HD scan unit, located at the SMS group headquarters in Düsseldorf, Germany (Figure 1). Based on the results, SMS group has designed a unit which can be used in industrial scale.

Aug 17, 2017

By Alessandro Martinis

The performance requirements for modern steelmaking facilities are ever more stringent, as customers and markets are continuously pushing for technologies which allow having high quality steel produced in an economic and sustainable way. In the details, this paper has the aim to present the excellent results obtained by integrated steel plant where an EAF is fed with high quality hot ENERGIRON DRI. The recent technology developments, combined with the affirmed basic process design, contributed to further maximize the energy of the DRI, reaching the EAF at temperatures above 600°C with a carbon content up to 3.5%, as confirmed by plant data. These improved input material characteristics resulted in reduced electrical energy consumption and increased liquid steel production.

Aug 16, 2017

By Anand Kumar Agrawal, Kinzel Klaus Peter, Lorenzo Micheletti, Cristiano Castagnola, Horst Kappes, Andre Oliveira, Björn Rösner, Philippe Bermes

Blast furnaces are widely employed today for iron production all around the world, with a total production of around 1.2 billion tons per year. Its operating principle, which relies on usage of coke to reduce the ore, to ensure the permeability in the reaction vessel, to maintain its flexibility of operation and acceptability for varying qualities of iron ores. The blast furnace route is widely considered as the most economic and efficient route of iron production, however it is based on fossil energy carriers. The blast furnace route has undergone significant developments in terms of energy efficiency in the last decades, which led to a substantial reduction in the use of fossil reduction materials. Being an energy intensive process, competitiveness and cost saving in the blast furnace plant was always strongly related to the saving of energy and hence reduction of CO2 emissions. In addition to this, EU emissions trading system (EU ETS) as a cornerstone of the EU's policy in response to climate change has set new “challenges” for iron production in Europe. Paul Wurth has always been deeply involved in the development of energy saving technologies for blast furnaces. In the following a review of energy saving achievements developed in the last decades will be presented and the potential of available CO2 saving technologies will be summarized. Additionally, an outlook about the potential of future technologies, concepts and their impact on the blast furnace and the steel plant’s energy balance will be discussed. Finally, the replacement of carbon by hydrogen as reduction agent in the steel plant will be reviewed, with special focus on a comparison of costs and incentives.

Oct 1, 2019

By Stefan Wahlund, Tom Adams, Mats Söder, Zhi Zhang

By applying high-end rolls with utmost performance and superior surface quality, hot strip mills can be further optimized. Operations in the mill have been also waiting for improved roll solutions that can minimize required roll changes which impact production efficiency. Limitations are usually due to the low performance and surface degradation of the rolls in the late finishing stands (F5 – F7). VICTURATM is the most recent developed grade for rolls utilized in the late finishing stand at Union Electric Åkers (UEÅ). These rolls have been tested and applied in mills all over the world. A significant improvement over the enhanced ICDP rolls has been observed. Hot strip mills are realizing improved operating efficiency and Total Cost of Ownership (TCO) through the transition of their entire roll inventories to these break-through products.

Oct 1, 2019

By Madson Pereira Martins

A utilização de resíduos oriundos de processos industriais tem se tornado uma prática muito recorrente em todo mundo devido à questão ambiental. A legislação brasileira estipulou parâmetros rígidos de destino destes materiais e a indústria viu na construção civil uma possibilidade de utilização. Este trabalho tem como objetivo a caracterização do pó de pedra de gnaisse para utilização em concretos. Serão realizados ensaios de granulometria, determinação de massa especifica e material pulverulento. Os resultados mostraram a viabilidade da incorporação deste resíduo para a produção de concretos.

Aug 16, 2017