Search Documents

By José Aparecido Pereira

The customer asked for a 5” angle roll pass design. For this angle, in a normal pass design, a 160mm billet is required. For the production of this billet would be necessary a new 160mm mold for the Continuous Casting Machine, which produces 150mm billets, increasing the complexity of the melt shop. The rolling mill is designed to produce angles up to 4", technical information recommended the replacement of a gearbox because this process would generate torque up to 15% above nominal. An innovative roll pass design was done using 150mm billet using the Aparecido-W Method that cause a higher spread in the first three passes, thus reaching the desired leg length. As this method is not used in any other known rolling mill, a FES (Finite Element Simulation) and FEM (Finite Element Modeling) was done by a Research & Development center which demonstrated that the design was viable. From July, 2018, three tests were done being produced around 700 t of good quality products without difficulty of set up. The rolling mill team carried out this project at a very low cost and in record time of five months. The average torque of the motors was 36%, without overload for the equipment.

Oct 1, 2019

By Sara Hornby

After almost half a century of experience in using DRI/HBI in electric arc furnaces (EAFs), and taking into account the decrease of natural gas cost in the USA, it is interesting to revisit some trends and controversial issues around this alternative iron source. This paper reviews aspects like the evolution of iron ore quality and its influence on EAF operation; DRI stockpiling and transport, regarding the risk for selfcombustion; optimum charge design; cold DRI/HBI charging (fifth hole, bucket, transporter); hot charging (ways and results); carbon content, metallization and silica in DRI/HBI, and its influence on EAF operation and performance; oxygen / carbon balance; chemical energy and DRI/HBI charge.

Aug 16, 2017

By Michaela Böberl

State of the art sinter coolers are working based on the cross flow cooling principle. Thus, only a part of the thermal energy can be used for heat recovery application. The other part of the cooling air is brought unused to the environment. Furthermore, environmental regulation regarding dust emission and intelligent usage of exergy are getting stronger. Therefore, Primetals Technologies developed sinter coolers based on the counter flow principle. The cooling air passes the sinter bed in counter-flow direction enabling a direct heat transfer from the hot sinter to the air. The exhaust gas temperature can be maximized by using the total heat of the hot sinter. Due to the possible usage of the total exhaust gas amount, diffusive dust emission is reduced to zero. Two types of counter flow coolers are in the portfolio of Primetals Technologies. One type is based on a stationary shaft, in which the hot sinter is charged. The flow of the hot sinter is in vertical direction from top to bottom, in counter direction than the cooling air. The second type is a circular hopper cooler. The hot sinter is charged on top of a moving bed. At the bottom of the bed the sinter is discharged. The cooling air flows also from the bottom to the top, following the counter flow principle. Depending on the requirements, one of the two counter flow cooler types can be chosen for optimized and efficient cooling of hot sinter..

Oct 30, 2017

By Gabriel Oliveira Glória

In the context of changing culture, the society is increasingly looking for environmentally friendly materials, the natural fibers appear as an option to substitute the synthetic. Among these natural fibers, the PALF fiber may be considered an option, but there is limited information about the flexural strength of epoxy composites incorporated with PALF fibers. Therefore, the objective of this work was to investigate the mechanical properties in bending tests of epoxy composites incorporated with up to 30% in volume of PALF fibers. The results showed that the PALF fiber increase the flexural strength of polymer composites.

Aug 16, 2017

By Simon Chiartano

A global reflection on the design of blast furnace main runner was investigated in this paper. TRB Company used its skills and expertise to understand what the best option for this sensitive component is, including some innovative tools: intelligent block design for safety lining, thermal & thermomechanical numerical simulation, immersive measurement by thermocouples, IR thermal camera, 3D laser scanner.

Oct 1, 2019

By Alberto Tremea

The eddy current system is universally recognized as a most suitable method to point out discontinuities or modifications on the roll surface. The automation of the controls through the implementation of sophisticated equipments on the grinding machine has favoured its employment in the roll shop. A big effort is still going on to clarify the best way to promptly identify situations that could be really unsafe for the roll life. The results presented in this paper have been obtained through an intensive activity conducted in field by Innse Cilindri on work rolls of finishing stands of hot strip mills. The correct interpretation of the eddy current signals and a good calibration of the automatic system have allowed, in many cases, a substantial optimisation of regrinding practices.

Aug 16, 2017

By Gabriel R. Royo

This paper will cover a back up roll bearing technological upgrade, being implemented at the TERNIUM SIDERAR Hot Strip Mill (HSM), in San Nicolas, Buenos Aires, Argentina. This change was motivated by increased operating loads, which caused the original bearings to be outside the designed bearing rating. The problems were first identified by bearing seizures in some stands, and later followed by cracks forming in the back up roll neck areas due to fatigue and overload. MORGOIL engineers worked together with TERNIUM SIDERAR engineers in analysing the problem and to upgrade the mill with the newest and most economical technology. The upgrade consisted of changing the bearings to the latest generation MORGOIL bearing: the KLX, which within the same space, increases bearing capacity around 25%. This was accomplished re-utilizing all chocks. The new bearing allowed for a re-design of the geometry of the back up roll neck, making it much stiffer than the original design, and eliminating fatigue failures. In addition, an upgrade to hydraulic mounting and dismounting using the MORGOIL® HB lock was also implemented, as well as changing to the newest MORGOIL® HD seals. With the MORGOIL® KLX® upgrade, TERNIUM SIDERAR HSM increased load capacity, allowing them to roll products that were not even considered decades ago. Both older oil film bearings and roller bearing mills have been successfully upgraded while reusing existing chocks and in many cases rolls. Solutions are customized to the customer’s equipment and goals.

Oct 30, 2017

By Vitor Guarnier Domiciano

Pre-shaped refractory burner blocks play an important role in reheating furnaces operation and melt shops production since they are responsible for heating the billets/plates so that they reach the temperature required for lamination. This paper presents the main characteristics and properties of a new refractory castable developed for pre-shaped burner blocks, which significantly improved the performance of reheating furnaces burner blocks. Tests carried out in 3 different melt shops have shown that the new refractory castable was able to extend the service life of the refractory burner blocks from 1 year (standard product) to more than 3 years (new castable), showing perfect conditions to continue operating for a longer period.

Oct 30, 2017

By Johan PEERS, François DUMORTIER

Today, solutions to optimize Capital Expenditure (CAPEX) & Operational Expenditure (OPEX) for small capacity Cold Rolling Mills (CRM) as well as for high capacity CRM are available, as extensively described by various Original Equipment Manufacturers (OEMs) & steel makers. A suitable solution for small capacity CRM is to start with a single stand reversing mill (up to 400 ktpy, depending on product mix), which can then be expanded into a twin stand mill (up to 900 ktpy, depending on product mix). The main drawbacks in conventional practice are the off-gauge length in single stand set-up and the long downtime of the mill during the erection of the second stand. For higher productions CRM, it is common practice to directly select a new Pickling Line Tandem Cold Mill (PLTCM), with a high CAPEX. Is there an in-between solution that would allow to start with limited output and CAPEX, without jeopardizing the ultimate expansion goal (1.2 to 2 mtpy), for which PLTCM is the best techno-economical choice? In the absence of a solution, JOHN COCKERILL developed an integrated solution that limits the CAPEX in the first phase of development, without crippling affecting future endeavors through an easy and economically sustainable expansion into a PLTCM, without long production downtime. The solution consists of first installing a twin stand mill, expandable into a tandem mill thanks to a smart design of the line. It is therefore possible to limit the production to 900 ktpy in the first phase of the project and then convert the mill into PLTCM in the second phase to increase the production from 1.2 to 2 mtpy, depending on the market trends and financial capabilities. In summary, JOHN COCKERILL has developed a smart new layout in reversing phase combined with a brand new rolling strategy to optimize productivity and limit off-gauge, compared to conventional solutions (patents pending). In addition the layout enables an easy conversion to tandem mill without high over investments, which is more sustainable financially than the initial purchase of a PLTCM. Long downtimes to allow for capacity extension, detrimental to this phase-by-phase approach, are also avoided. Technical and process description of the new layouts and rolling strategies, together with CAPEX & OPEX descriptions of the phases are detailed in this paper.

Oct 1, 2019

By François DUMORTIER

Due to the increasingly stringent requirements and the needs of the automotive industry, galvanizing lines for automotive products have to be modernized and improved. Beginning of 2017, SEGAL, a Tata Steel CGL located in BELGIUM and fully dedicated to automotive market, placed an order to increase the line capacity from 550kt/year to 600kt/year to process a wider range of steel grades and improve the product quality according to automotive requirements. To improve quality, a major revamping of the skin pass was necessary. The objectives were first to increase the work roll diameter from Φ560mm to Φ650mm to be able to transfer the required roughness with low elongation on soft material and second to increase the rolling force and tension to reach higher elongation on high strength steels. The result was the adaptation of the whole skin pass mechanics. Old mechanical elongation system has been replaced by a completely new single AC motor with helical gearbox at each bridle roll. John Cockerill achieved such complicated revamping in a very short time since the shutdown started only 6 month after the contract signature. The shutdown down schedule has been optimized with pre-erection works and the teams working 24/7 to implement all the changes. The complete project (skin pass, furnace, loopers) have been adapted during the three weeks shutdown. Today the customer can use both 560mm and 650mm work roll diameters. Thanks to the use of the new 650mm work roll diameter, the customer is able to make the same elongation using a bigger roll force (average 20% more), which has strongly improved the roughness transfer to the strip and the removal of the defects. SEGAL is really satisfied able to produce and supply higher quality automotive products to his customers.

Oct 1, 2019

By Mathias Woydt

The tribological and mechanical properties of binderless and metal-bonded niobium carbides (8 or 12 vol.-% of Cobalt, 12 vol.-% of Fe3Al) are presented. Rotating disks made of niobium carbide bearing hard metals were mated against alumina (99.7%) under unlubricated (dry) unidirectional sliding tests (0,1 m/s to 12,0 m/s; 22°C and 400°C) as well as in oscillation tests (f= 20 Hz, ?x= 0,2 mm, 2/50/98% rel. humidity, n= 105/106 cycles). Microstructure and phase compositions were determined as well. The tribological data obtained were benchmarked with different ceramics, cermets, hard metals and thermally sprayed coatings, where NbC bonded with 8% and 12% Co presented above 8 m/s the lowest wear rates so far in such a benchmark. Binderless NbC (HP-NbC1) and the metal bonded NbCs exhibited low wear rates under dry sliding associated with high P?V load carrying capacities. NbC-based hard metal bonded with 12 vol.-% of Fe3Al resulted in a higher hardness level than for 12 vol.-% cobalt. The tribological profile established revealed a strong position of NbC bearing materials under tribological considerations and for closed tribosystems against established reference tribo-couples.

Jul 31, 2018

By Henara Lillian Costa

This paper aims to investigate the effects of a possible incorporation of ethanol to the lubricant during engine use on friction and lubricant film thickness, by adding small amounts of ethanol to Group I base (with and without an organic friction modifier) and to formulated oils. Film thickness was measured using ultrathin film interferometry. Friction tests were carried out using a mini-traction machine to obtain Stribeck curves. The film thickness measurements showed that in the region of low speeds, where the elastohydrodynamic film is very thin and therefore boundary lubrication may prevail, the addition of ethanol produced some boundary film, which was not present for the base oils. For the base oil with an organic friction modifier, the presence of ethanol increased the thickness of the low friction boundary film. For the formulated oil, the addition of ethanol reduced film thickness in all lubrication regimes. The friction tests showed some friction reduction due to addition of ethanol to the base oil, in particular at low speeds. For the formulated oil, the addition of ethanol reduced friction at high speeds, which was associated to a reduction in the viscosity of the lubricant, but at low speeds, the presence of ethanol reduced the formation of a boundary layer, increasing friction. For the base oil containing an organic friction modifier, the presence of ethanol increased the range of speeds for which low boundary friction occurred.

Jul 31, 2018

By Kelen Juliane Mucelin

In order to better understand the tribological behavior of self-lubricating materials, Fe-Si-C matrix composites containing solid lubricants added during the mixing step were studied. The samples were produced by conventional powder metallurgy route, presenting total contents of 5%, 7.5% and 10% in volume of h-BN and graphite mixtures as solid lubricants. The composites were evaluated in terms of tribological properties, under reciprocating sliding conditions, and mechanical properties by using tensile tests. Additionally, the wear scars were characterized by Raman spectroscopy and scanning electronic microscopy. Higher total contents of solid lubricants greatly increased scuffing resistance however decreased mechanical properties. Furthermore, increasing h-BN contents reduces both properties. These results confirmed the applicability of such sintered composites as self-lubricating parts, reaching values up to 7000 N.m for scuffing resistance combined with ultimate tensile strength of 220 MPa.

Jul 31, 2018

By Michael Windhager, Karl H. Ziehenberger

ULTIMA® are high performance, centrifugal cast, double poured (CC duplex) work rolls. This paper describes the principle of the ULTIMA® roll concept and its wide range of usability. The ULTIMA® concept provides a solution for rod and bar mills to increase performance and output, even under harsh rolling conditions. The main focus is on highly loaded mill stands that require both high wear resistance and resistance against thermal fatigue, like pre-dog bone, dog bone, slitter. Specific case studies of quite different mill configurations and rolled product mix prove the positive impact on production yield, mill and roll shop operations, and profitability in terms of TCO (total cost of ownership).

Oct 1, 2019

By Gabriel Rodrigues

_test

Oct 24, 2018

By Jean-Philippe Houde

The Blast Furnace Campaign lifetime is highly depending on the wear progress of the hearth lining. This progress is monitored in general through single and double thermocouples at the cold side of the lining. This type of monitoring becomes ineffective as soon as heat resistance will be formed in the refractory lining. Paul Wurth’s monitoring system, consisting of MTP-Sensor and Heat Flux Probes, is able to identify such heat resistances to give a true hearth lining wear. Since last year Paul Wurth is also able to install safely those MTP-Sensor and Heat Flux Probes on running blast furnace without salamander tapping, thanks to a newly developed cooled core drilling device. Blast Furnaces that are equipped with Paul Wurth’s monitoring system have optimized their campaign lifetime as they received right information upon the true wear lining such as detection of heat flux transfer failure, detection and monitoring of brittle layer or detection of hot spot.

Aug 16, 2017

By Renata Cristina Teixeira

The lubricant oil is a complex mixture of different basestocks and additives. Engine oils evolved from the use of pure mineral basestocks back in the early years of automotive industry to the advent of synthetic, fully formulated, low ash lubricants. This evolution was driven by a number of factors, such as new engine designs, extended durability needs, increased fuel economy needs, environmental concerns, feedstock prices and availability and legal issues. This paper uses technology prospecting on literature and patents databases to allow an investigation on the historical evolution of engine oils. Main basestocks (mineral, hydrotreated, polyalphaolefins, esters) and additives (antioxidants, antiwear, friction modifiers, detergents and dispersants) are characterized according to their research effort. Technology prospecting data is crosschecked against the evolution of engine oil classes, allowing an analysis of how the main drivers push the development of lubricant oil quality. A research effort was identified in late 1990’s until mid-2000’s and related to the adoption of chemical limits for lubricants. Different patterns for the articles and patents publication account for the high value technological knowledge has in this industry. Technology prospecting is seen as a useful methodology for the understanding and forecast of lubricant technology movements.

Jul 31, 2018

By Gabriel Oliveira Glória

Due to growing concern about the ambient impacts, lignocellulosic fibers are been investigated to replace the synthetic ones in polymer composites The giant bamboo fiber, a relatively unknown lignocellulosic fiber with potential for composite reinforcement, still needs to characterize for possible engineer applications. However the giant bamboo fiber has low adhesion with the polymeric matrix. In order to understand the interaction that occurs between the bamboo fiber and the polymer matrix is necessary to evaluate its physical and chemical characteristics. Therefore, the present work analyzed the giant bamboo fiber by means of Fourier Transform Infrared (FTIR) spectroscopy. The spectrum revealed main absorption bands typical of giant bamboo fiber specific molecular interactions.

Aug 16, 2017

By Maycon de Almeida Gomes

Fiber reinforced polymeric composites have received widespread attention in the past four decades because of their high specific strength and modulus. In particular, research works have disclosed the potential advantages associated with the use of lignocellulosic fibers as the reinforcing phase in polymer composites (2-3). Among various natural fibers, pineapple leaf fibers exhibit excellent mechanical properties. The main chemical constituents of pineapple fibers are cellulose (70–82%), lignin (5- 12%) and ash (1.1%). The superior mechanical properties of pineapple leaf fibers are associated with their high cellulose content (6). This work aims to make the analysis of the Izod impact energy against volume fraction of palf fibers of epoxy composites reinforced with PALF. The fibers were incorporated into the epoxy matrix with volume fraction from 0 to 30%. After fracture the specimens were macro photograph analyzed.

Aug 16, 2017

By Fernando Ruiz Díaz

En aplicaciones a elevadas temperaturas como por ejemplo en cámaras de combustión y toberas de vehículos aeroespaciales se requiere el uso de aleaciones que permitan una elevada extracción de calor y buenas propiedades mecánicas. En este trabajo se realiza un análisis comparativo de las aleaciones Cu-Cr-Zr y Cu-Ag-Zr. Las mismas fueron sometidas a ensayos de resistividad eléctrica entre 25ºC y 700ºC y de tracción a 150ºC, 450ºC y 700ºC. Los resultados de los ensayos de resistividad eléctrica fueron convertidos a conductividad térmica mediante la relación de Wiedemann- Franz. A través de este análisis se observa que la aleación con mejor conductividad térmica es la de Cu-Ag-Zr presentando además un cambio de fase que no es observado en la aleación Cu-Cr-Zr. Respecto al ensayo de tracción la aleación Cu-Cr-Zr presenta mayores valores de resistencia a la tracción y tensión de fluencia a las temperaturas estudiadas.

Aug 16, 2017