Search Documents

Mineral Industries education as an entity, again and again has sought recognition, always to be turned aside or ignored.1 The incident mentioned in Lost Chapter was only the first of a series of disappointments. The Land-Grant Act is camouflaged here and there in the name of progressive education. A new interpretation may be in the best interests of society in so far as the goose is not killed that lays the golden egg. The primary objective of the act is still "agriculture and mechanic arts" but mechanic arts is not alone mechanical arts or engineering. Mechanic arts was used in a broad sense as a symbol of creative effort in locating and winning the fundamentals of existence - plants, animals, and minerals - from Mother Earth, their primary processing and treatment into foodstuffs and raw materials of industry, their manufacture into useful articles of commerce, and, last, their distribution and utilization. Significantly the great agricultural industry is now at least half mechanic arts. The Association of Land-Grant Colleges and Universities has neglected the mineral kingdom shamefully. The Association embraces Divisions of Agriculture, Arts and Sciences, Engineering, Home Economics, and Veterinary Medicine but has no division relating to the mineral industries.

Jan 1, 1950

By Mark D. Tabak

Measurments of the transient photoconductivity in fillns of amorphous selenium with blocking- contacts haue been used in studying the transport properties. The results shozu that the transport of free carviers cannot be explained in terms of a model using bulk trapping. Measurments of the photocurrent-applied field characteristic as a unction of sample thickness do not pvoduce the scaling lau,s approps-iate lo a range-limited model. THE investigation described here was undertaken to explore the mechanisms of transport in amorphous selenium films. These films are used in xerography, where a photoconductor is charged electrostatically and then exposed to light to form a latent image. The sensitivity that one can expect when operating in this mode is directly related to the transport properties of the photoconductor material. The study of photoconductivity at high fields in insulating materials is often complicated by contact effects. Injection from the contacts can easily mask the fundamental transport processes that are being studied. A technique is described in this paper that allows a study of photoconductivity and transport processes in amorphous selenium films without the complicating effects introduced by contacts. Accordingly, the samples are prepared using insulating films between the sample and the metal electrodes, where the electrodes are capacitively coupled to the surfaces of the sample under study. A transient measurement is performed with pulsed light, and the photocurrent measured near the beginning of the pulse before the field is distorted by polarization at the blocking elec- trodes. A similar method has been described by Manyl using pulsed electric fields in studying the high field transport in insulating cadmium sulfide. EXPERIMENTAL It is possible to eliminate undesirable contact effects and maintain uniform high fields across the sample by using blocking electrodes and measuring the current-field characteristic under transient conditions. The sample configuration is shown schematically in Fig. 1. Each of the gold electrodes is separated from the amorphous selenium film by a layer of insulating plastic (Formvar) approximately 2000~ thick. The electrode on the front surface is semi-transparent to allow illumination of the sample. The whole configuration is mounted on a KEL-F substrate, which is a transparent insulating plastic having a thermal expansion coefficient that allows low-temperature measurements without cracking the selenium film. Fig. 2 shows a block diagram of the measurement apparatus. Light was obtained from a 450-w Xenon arc lamp, the intensity of which was controlled by stainless-steel screen filters and monitored by a pho-tomultiplier which was calibrated periodically against a thermopile. A camera shutter operated at 1/200 sec provided the light pulse and a synchronized signal to the oscilloscope. The photocurrent transient is ob-served with a high-speed picoammeter (response time of 1 msec) the output of which is displayed on an oscilloscope. The applied voltage is constant throughout the transient measurement. The selenium films were prepared by evaporation of four 9's pure selenium shot supplied by Canadian Copper Refiners. Spectrographic analysis showed about 1 ppm of Te and Fe, 5 ppm of C1, and 0.05 ppm

Jan 1, 1968

By R. P. Smith

The carbon content of a number of alloys ranging (before carburitation) from purified iron to purified cobalt was determined for fixed activities of carbon by equilibration with each of six CO-CO2 atmosphere at 1000°C. At fixed carbon activity, the carbon content decreases continuously with increasing cobalt content. For concentrations of 0 to 50 at. pct Co the results can be expressed by a linear interaction equation of the type In y2 = 7.76n2/(n1+n3)+ 2.30 n3/(n1+n3) where y2 is the activity coefficient of carbon (standard state such that y2— 1 as n2 — 0 in the Fe-C binary) and n1, n2, and n3 are the number of atoms of iron, carbon, and cobalt per unit weight of alloy. The results are also given in terms of the a functions. In the same concentration range, the results are in accord with the regular solution theory of Alcock and Richardson. THE carbon content of Fe-Si, Fe-Mn, and Fe-Ni alloys at fixed activities of carbon has been reported previously.'-, The present work extends R. P. SMITH, Member AIME, is Research Chemist, E. C. Bain Laboratory for Fundamental Research, United States Steel Corp., Research Center, Monroeville, Pa. these measurements to a series of Fe-Co alloys. These alloys, like the Fe-Ni alloys, are fcc ("aus-tenitic") over the entire range of composition at 1000°C. EXPERIMENTAL PROCEDURE The alloys were made from electrolytic cobalt and Plast-Iron in a small vacuum-melting furnace. A small amount of graphite was added to each melt to keep the oxygen content low. The ingots were analyzed for iron and carbon: the amount of cobalt was obtained by difference. Analysis of the top and bottom of the ingots indicated that they were uniform in alloy content. Except for the pure cobalt the ingots were hot-rolled to approximately 0.15 cm thickness, cleaned by sandblasting, then cold-rolled to about 0.045 cm. We were not successful in cold rolling the pure cobalt; therefore it was hot-rolled to the final thickness. The last traces of surface oxide were removed by acid pickel, then the samples were treated in a hydrogen-2 pct water vapor mixture at 1100°C to remove carbon and most of the oxygen. The carburizing procedure was similar to that previously described.1,2,4 The alloys in the form of strips about 1.7 cm wide, 7.5 cm long, and 0.04 cm thick, together with a similar specimen of purified iron, were equilibrated with each of six CO-CO2 mixtures of fixed composition, then quenched in the

Jan 1, 1965

THERE was presented for discussion at the February (1924) meeting of the American Institute of Mining and Metallurgical Engineers a report of a committee named by the United States Bureau of Mines on the Use of Oxygen or Oxygenated Air in Metallurgy and Allied Processes. An extensive discussion followed the presentation of the papers, which dealt with the matter entirely from a theoretical standpoint. The results of only a limited, amount of research work were presented and discussion centered around the question: "Is it worth while to carry on research and expend money in determining what can be done in metallurgical operations if cheap oxygen can be produced?" More experimental work on this subject has not been done because metallurgists have not thought that cheap oxygen could be produced, thinking "Why waste time experimenting. with a reagent that cannot be procurable in commercial quantities?" While the producers of oxygen have said " Why waste money on the development of a process to make cheap oxygen unless we know that there will be a market for it when produced?" The discussion brought out two facts: First, many metallurgists believe that their operations can be conducted more economically if they can add oxygen to the air used in various smelting operations; second, a number of chemists believe that relatively pure oxygen can be produced in metallurgical quantities at very small cost. Negative views were expressed to both propositions, but so overwhelming was the view that if cheap oxygen could be produced, many metallurgical operations would benefit that it was voted to recommend that the Bureau of Mines continue its research work, pending the production of the cheap oxygen hoped for. Few experimental data being available, and the attitude of disputants being based largely on theoretical considerations or on reactions and temperatures incapable of positive proof, it has been decided to publish only a summary of the papers and discussions arising from their presentations. It is believed, however, that this will be sufficient to show the lines of reasoning that have been adopted, and be a guide to others who are to make their own calculations or engage in experimental work.

Jan 11, 1924

By Edward W. Mehal

This paper presents a review of the technologies which have been used in the application of III-V compound semiconductors to integrated circuits and arrays. These materials have properties which make them useful for various devices such as: light emitters, sensors, microwave sources, and microwave diodes. Technologies for incorporating these devices into integrated circuits have been reported and processes developed for fabricating planar devices using selective epitaxial deposition or selective diffusions. Isolation methods utilizing semi-insulating GaAs, oxide isolation, and ceramic insulation have also been reported. These techniques, and the devices and circuits produced or proposed are discussed. AFTER the invention of the silicon-integrated circuit, methods for utilizing compound semiconductors for integrated circuit applications were proposed. The scope of applications was potentially much broader because of the range of properties available from these materials. There also was the opportunity of coupling these properties with germanium and silicon devices to realize functions and circuits which could not be produced with silicon monolithic circuits. Table I exemplifies the range of electrical properties available in III-V compound semiconductor materials which are currently being widely used. A wide range of sensor and emitter applications result from the range of band gap. The band structure of GaAs and GaAsxP1-x permits their use as microwave oscillator source, and the high electron mobilities further facilitate their utility in microwave devices. The concept of "integrated functions"1 results from the availability of these materials and methods for utilizing their special properties. Heteroepitaxial growth allows the fabrication of a monolithic block of these materials. Semi-insulating GaAs permits the attainment of electrical isolation between components in a monolithic block without resorting to p-n junction biasing or oxide isolation methods. An "integrated function" is a unit which can perform a system or subsystem role and perform a number of electromagnetic functions. These functions could include sensor or input transducer, signal processing, interconnections, and control or output function. Two examples which demonstrate this concept are an optoelectric processor and a microwave receiver front end. The optoelectronic processor, Fig. 1(a), would consist of a light sensor, signal processor, and output emitter. The sensor could be InSb or InAs which would be IR-sensitive. The signal from this sensor would then be amplified and transmitted to the light emitter. The amplifier could utilize GaAs bipolar or field effect transistors. A Gap emitter would then produce visible radiation. The microwave receiver front end, Fig. l(b), would consist of a local oscillator section and a mixer section. A signal input from an antenna is mixed with the signal from the local oscillator. The local oscillator signal is produced by a Gunn oscillator. The single-ended mixer utilizes one Schottky barrier mixer diode. The IF signal would then be amplified further and suitably displayed. A further extension of the capability of utilizing the

Jan 1, 1969

By E. P. Palmatier

RECENTLY a cooling system has been in process of installation on the 3400 and 3600-ft. levels of the Magma copper mine at Superior, Ariz. The general system of ventilation employed at this inclined-vein mine is as follows: Ventilating air enters the shafts on the western side of the mine. Booster fans at each level each deliver approximately 38,000 cu. ft. per 'min. to the drifts. This air passes diagonally upward to the upper levels of the mine on the eastern side, where it passes up the shafts to large exhaust fans on the surface. Owing to the dip of the vein, all operations on the eastern side of the mine are above the 2500-ft. level, and those on the western side below the 2500-ft. level. At present, 2500 lineal feet of new drifts are being driven-on each of the 3400 and 3600 levels. The rock temperature is about 135°F. Until the new installation is completed, ventilating air for the two levels is supplied through Flexoid tubing from small booster fans -on the 3200-ft. level. The air picked up by these booster fans has a dry-bulb temperature of approximately 85°F. and a wet-bulb temperature of 82°F. By the time this air reaches the end of the Flexoid tubing at the 3600-ft. level, the dry-bulb rises to 101°F. and the wet-bulb to 86°F. The conditions at the head of the new drift were 102' dry-bulb and 93' wet-bulb.

Jan 1, 1937

By AIME

Generally speaking, the mining industry had a good year in 1948 with most mineral products being produced in record quantities for peacetime standards. The big boys-iron and steel, coal, and petroleum-indicated the industry-wide trend by surpassing 1947 production figures. Although exploration and expansion are being pushed aggressively in all branches of the industry, there is a pronounced trend to engineering and research directed at cutting production costs, improving the product, and finding new markets. These improvement campaigns are making headway; in the bituminous coal industry, 5.43 tons per man employed is the new production record; 83 million tons of iron ore were unloaded at lower Lake ports, breaking another peacetime record; magnesium, due to improvement in manufacturing techniques, now competes on the market with aluminum.

Jan 1, 1949

By N. J. Grant, Hans Brunner

ThE materials used in this investigation were furnished by the Aluminum Co. of America and consisted of high-purity alurhinum (99.995 pct) and two aluminum-magnesium alloys containing approximately 2 and 5 pct Mg. The compositions of these alloys are listed in Table I. The materials were received as hot rolled 3/8-in. diam rods and were made from the same heats as the materials which were previously used in this laboratory.'j3 The rods were cold swaged to 1/4-in. diam by 1 in. long, and then had two parallel flats machined over the gage length 0.085 in. apart. The test bars were annealed for 10 min at 700° F, and strained 1 pct in tension at room temperature. They were electropolished (80 pct acetic acid; 20 pct perchloric acid, 70 pct concentration) at a temperature of 60°F at approximately 20 v. A grid, transverse or square, spaced 0.2 mm apart, was impressed by rolling a fine threaded screw (128 threads per in.) across the flat surfaces. The depth of the grooves was less than 5 p. For final annealing and grain size control the specimens were enclosed in aluminum foil and sealed in Vycor tubes. Annealing conditions varied from 1 hr at 700° F to 5 days at 1050° F, depending on the alloy content, to give for most of the specimens a final grain size of about 1 mm. This treatment was followed by electropol-ishing as described above. For the test series presented in Figs. 4 and 5 round specimens were used instead of flat ones, and fine machining marks served as marker lines instead of the impressed grid lines. Electropolishing was omitted. The major advantage is that the spacing of the machining marks is only about 1 u as compared to the 200 u of the impressed grid lines, permitting higher precision in strain measurements. Unfortunately the strain annealing necessary for grain size control also resulted in some preferred orientation of the grains. The preferred orientation of three arbitrary specimens was measured by X-ray diffraction methods and the averaged results are shown in Fig. 1. The possible effects of the preferred orientation on the test results will be discussed later. The testing temperatures were 410°, 515", 725", and 940° F, with one exception in the case of the 5.1 pct Mg alloy. Since the solubility limit of this alloy is 520°F, a test temperature of 545°F was cho-se sen instead of 515°F. The selection of the test temperature was based on two considerations: 1) at 900°F and above, extensive grain boundary migration made it more difficult to measure grain boundary sliding; 2) at 400°F and below, there was so little grain boundary sliding that it was again difficult to make precise measurements. The stress was chosen to give a creep rate of approximately 2.7 pct per hr in connection with Figs. 2

Jan 1, 1961

By Raymond J. Kujawa

For general purposes, insulating materials may be any of those mineral substances that provide a barrier between a desired human environmental feature and an unwanted condition. In this sense, radiation shields, electrical insulations, cryogenic insulation, and acoustical barriers would qualify. For this chapter only the thermal and acoustic insulations used for the median range of normal comfort control will be covered. Because of their magnitude and complexity the other fields are left to other chapters. In another sense, this section deals only with the ultra-lightweight aggregates and insulations, rather than the multitude of light-weight structural materials. Definitions and Uses The insulating materials covered in this chapter are the three groups of mineral products that provide thermal or acoustic barriers through the median temperatures encountered in home and industry. The three mineral categories are perlite, vermiculite, and the silicate wools whether they be categorized as glass, mineral, or rock. Perlites are those amorphous aluminum silicates with minor impurities that take the form of a felsitic, glassy lava possessing a pearl-like luster and concentric cracking. In a more commercial sense the term is used to describe either the natural or processed acidic, volcanic glass, containing from 2 to 5% combined water, that may be converted to a frothy mass by heating rapidly to the softening point. Vermiculites are micaceous, hydrated magnesium iron aluminum sheet silicates of varying composition. Commercial vermiculites are any of these sheet silicates that are capable of sufficient expansion on rapid heating to make an acceptable, highly porous product. Mineral wools, rock wools, silicate cottons, glass fiber are generic names for manufactured fibers in which the fiber forming substance may be slag, certain rocks, or glass. The fibers may be made by a blowing or spinning process. The resultant fibers may be felted or matted or gathered in the manner best suited to the use. The three groups may be used competitively to insulate ceilings and walls. The fibers have strong advantages in this area as they may be manufactured in batts that are stable in residential wall construction. The perlites and vermiculites are more suited to insulate cores and cavities of masonry walls and as plaster and concrete aggregates for thermal insulations. Vermiculite is widely used for insulating attic floors. Because of manufacturing techniques and controls, the glass fibers have made great strides as composites in the plastics industry but only a few of these uses classify in the insulation category.

Jan 1, 1975

By M. H. Merriss

IN THE last few years, there have been developed at the plant of the Nichols Copper Co., Laurel Hill, Borough of Queens, New York City, improvements in electrolytic copper refining by the series system that have materially increased the flexibility and economy of that system. The purpose of this paper is to discuss, as of interest to refiners and to those who have copper to refine, as well as to the engineering profession in general, the changes that have taken place resulting in wider application and increased efficiency of the series system. Copper is electrolytically refined in two ways, which are spoken of as the "multiple system" and the "series system." In both systems, the electrolytic tanks are in series electrically. In the multiple system the electrodes in a single tank are in multiple or in parallel, thus: In the series system, the electrodes in a single tank are in series, thus: There are two important adaptations of the series process, one represented by the series electrolytic tank room at the Baltimore Copper, Smelting & Rolling Co., Baltimore, Md., and the other by that of the Nichols Copper Co.'s plant. At Baltimore, the anode is rolled to perfect

Jan 6, 1925

By Robert H. Weber

INCREASING acceptance of perlite products, chiefly in the fields of lightweight structural aggregates and thermal and acoustic insulation, has led to expanding market demands that have encouraged many new producers to enter the field. In some instances, however, the failure of these producers to anticipate the variable response of perlite to conventional processing methods has led to difficulty in establishing an economical flowsheet by which a predictable specification product could be obtained. It is not the writer's intent to provide a solution to these problems, but rather to summarize their nature. It is to be hoped that members of the industry who have hurdled some of these obstacles will document solutions arising from their experience. In this treatment the term perlite will not be restricted to the petrographic definition but will apply to all volcanic glasses. Expansible obsidians and pitchstones are accordingly included in this broader industrial classification. Chemical Properties: Although perlite has been reported to range in composition from that of rhyolite to that of andesite, it is probable that most of the glasses have the composition of rhyolite. When recalculated to an anhydrous basis, the five analyzed glasses from New Mexico, representing five distinct physical types from widely separated deposits, show an amazingly uniform oxide composition. Water content is the only major compositional variable; total water ranges from a low of 0.37 pct (non-expansible obsidian) to a high of 8.95 pct (expansible pitchstone). The wide range in expansion characteristics exhibited by these samples cannot be related to significant variations in the composition of the nonvolatile fraction and has been only partially correlated with variations in water content.

Jan 1, 1956

By M. R. Annis

Drilling mud rheological and gel property changes due to elevated temperatures frequently cause problems in drilling deep wells. A laboratory investigation of the effects of time, temperatures up to 3001; and mud composition on these properties was made with concentric-cylinder, rotational viscometers of the Farm type. The viscometers were sealed from the atmosphere to prevent dehydration of the sample. Gel strengths were found to be more sensitive than viscosities to changes in temperature and mud cornposition. The high-temperature gel strengths of bentonitic clay drilling fluids were not predictable from low-temper.atl4t-e measurements. At high temperatures, [lie clay flocculates. The floccu-lation temperature depends on the concentration and type of solids in the mud and the degree of chemical defloccula-tion. As the bentonite content of a mud increases, floccrrla-tion temperature decreases. Lignosulfonnte treatment raises the flocculation temperature. To minimize adverse high-temperatrrre effects on mud properties, the mud should be maintainted at minimum solids content, properly treated with. a defloccullant which is stable at the maximum ten?perature encountered and maintained at a pH high enough to insure activation of the deflocculant for the duration required. The Methylene Blue Test for cation exchange cnpacity of a clay was found to be a useful guide in deter.niinirig when a mud contains a dangerously high clay conWnt. INTRODUCTION In drilling a well it is desirable, for several reasons, to know the effects of time and temperature on the rheological and gel properties of the drilling fluid in the hole. Problems associated with drilling fluids normally occur down-hole: so it is reasonable to be interested in the properties of drilling fluids at the conditions which exist down-hole. It has long been observed that high pump pressures are often needed to start circulation after a trip and that the "bottom-up" mud that is circulated back to the surface is usually more viscous than it was before "cooking" at the bottom of the hole for several hours. Burk-hardt' showed that a knowledge of rheological proper-ties of muds under down-hole conditions is necessary to predict pressure surges. He showed that the viscosity of a mud greatly influences the magnitude of pressure surges and the likelihood of lost returns. McLean et aL~ showed that the rheological properties of a mud under down-hole conditions are very important to cementing operations. This paper presents data showing the effects of time and temperature on rheological and gel properties of water-base drilling fluids. Measurements of gel strengths and rheological properties were made with two different concentric-cylinder rotational viscometers of the Fann type. One was the conventional six-speed viscometer modified to operate at temperatures up to 350F and at the vapor pressure of the liquid at test temperature. The other viscometer was newly designed to operate at temperatures up to 500F and pressures up to 1,000 psi. Tests with both instruments were made under essentially the same operating conditions. The new viscometer is shown in Fig. I. In this investigation, great emphasis has been placed on the rheological properties of clay suspensions, since clays are largely responsible for a mud's thixotropic and gel-

[ARTICLE I. NAME AND OBJECT Section 1. This Society shall be known as the Society of Petroleum Engineers of the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. Section 2. The object of the Society of Petroleum Engineers shall be to furnish a medium of cooperation among those interested in the petroleum-natural gas industry an to promote the advancement of this branch of mineral technology through meetings to stimulate the preparation, reading, discussion and circulation of papers connected therewith. ARTICLE II. MEMBERS Section 1. Any person who is a member of AIME may become a member of this Society by the specified process. Section 2. Local organizations may be formed by the Society of Petroleum Engineers as subsidiary units, the membership of which shall be subject to and in accordance with the by-laws of the Institute.]

Jan 1, 1961

By D. E. Spiller

Introduction Precious metals recovery from ore can generally be accomplished using gravity concentration, flotation, and/or hydrometallurgical (leaching) techniques. The objective of this paper is to show why gravity concentration can be an important part of recovery systems that employ leaching as the primary unit operation. A brief discussion of modem gravity concentration equipment is also presented. Discussion Gravity concentration of ores has generated increasing interest in recent years. Reasons for this interest include: • Gravity concentration is environmentally attractive. There is little or no use of reagents. Hence, it is relatively nonpolluting. • The cost of cyanide has continued to increase. Therefore, cost savings may be realized whenever leaching feed tonnage can be reduced by preconcentration. • Compared to flotation and leaching, gravity equipment costs are low per processed ton. Field installation costs for gravity circuits usually are less because many' units are supplied as self-contained modules. Also, the cost required to supply services, particularly power, to a gravity plant site are also less. In situations where preconcentration at coarse particle size is applicable, significant grinding equipment savings may be possible. • Gravity circuit operating costs are also relatively low compared to typical flotation and leaching circuits. Reagents, power, maintenance, and manpower savings in a well-engineered gravity plant may be realized. Again, if grinding is reduced, significant power and steel (media and liners) savings are possible. •In recent years, more efficient gravity concentrating devices have been developed. Benefits to Precious Metal Leaching Gravity beneficiation can complement precious metal leaching in two ways. First, the recovery of coarse liberated values before leaching may reduce leach time requirements and may reduce reagent consumption. Second, gravity preconcentration can reduce the size of a leach plant by decreasing the quantity of material to be leached. Coarse gold and silver have been shown to leach rather slowly. Kameda (1949) and Habashi (1967) have investigated the kinetics of cyanide leaching systems. They concur that in a heterogeneous reaction, the rate of gold and silver dissolution is directly proportional to the surface area. Thus, the instantaneous rate of dissolution for spherical 0.37 mm (400 mesh) gold is theoretically -25 times faster than for the same amount of gold at .841 mm (20 mesh), based on data from Fuerstenau, Chander, and Abouzeid (1979). Conversely, coarse liberated, +.841 mm (20 mesh), gold is more readily recovered by gravity concentration than is fine, -.037 mm (400 mesh) gold. Therefore, it is apparent that the two recovery systems complement one another. Figure 1 data demonstrates the potential synergism. A sample of - 3.327 mm (6 mesh) Nevada gold-bearing ore was cyanide leached using conventional bottle-roll test procedures. Gold extraction was determined as a function of leaching time. A second sample split from the same leach feed material was hand jigged to remove a coarse heavy mineral fraction, including virtually all of the +.210 mm (65 mesh) liberated free gold. This second sample, with the coarse gold and heavy minerals removed, was subjected to an identical cyanide leach procedure. Figure 1 presents the resulting comparative extraction data. Note that the percent gold extraction for the sample containing no +.210 mm (65 mesh) free gold includes the coarse gold recovered by gravity. The data show that the sample containing coarse gold required about 72 hours of leaching time to achieve 80% extraction. This compared to about 22 hours of leaching time for 80% gold recovery from the sample that contained only -.210 mm (65 mesh) free gold. Thus, there was a 69% reduction in leaching time. The improved extraction data is not wholly attributable to coarse gold removal, but rather it was the combination of gold removal and rejection of other heavy mineral cyanide consumers or leach retardants. Further investigation was not warranted at this time. Preconcentration is the second manner in which leaching systems can benefit from gravity concentration. The premise is that preconcentration can reduce the quantity of leach feed, which, in turn, may reduce leaching costs. Figure 2 presents preliminary data developed by CSMRI for US Minerals Exploration (USMX). Centennial Exploration Inc., in agreement with USMX, is proceeding with evaluations to determine the suitability of various processing schemes for recovery of gold values from the Montana Tunnels property. The data shows how the ore can be preconcentrated by gravity techniques to result in a reduced feed tonnage to secondary extraction techniques, presumably flotation or cyanide leaching. Testing has shown that Reichert cones, followed by treating the cone concentrate on spirals, can deliver about 88% gold recovery in about 13% weight, that is, 87% weight rejection. Consequently, fine grinding and reagent costs are attributable to only 13% of the plant feed rate. Cost data is not yet available, but the potential exists for significant cost savings.

Jan 1, 1985

By Donald J. Drinkwater, M. C. Fuerstenau

Many important contributions to the more fundamental aspects of mineral processing have been made this past year. Mular1 researched the flotation characteristics of pure zinc oxide and also samples that had been doped with Al+++ and Cu++. Correlation of the response of pure zinc oxide to oleate flotation with a calculated zpc (from solution equilibrium) suggests that adsorption of oleate ion is coulombic in nature. Doping the sample with Al+++ (which will make the ZnO more n-type) had a marked effect on the maximum value of pH at which 50% recovery was obtained at constant collector addition. That is, when 0.5 mole percent Al+++ was added, the pH for 50% recovery was reduced by about four units. Treatment with Cu++ was found to have little effect on the flotation response of zinc oxide, even for additions of one mole percent. Since the zero points of charge of the Al+++ doped powders were not measured, it was not possible to correlate flotation data of these samples directly with charge phenomena.

Jan 2, 1966

By AIME AIME

FOR constructive research in copper and brass and other non-ferrous metals and their alloys, and his contributions to the establishment of the present accepted high standards of quality William H. Bassett, technical superintendent and metallurgist of the American Brass Co., has been awarded the James Douglas Gold Medal for 1925. Mr. Bassett was born in New Bedford, Mass., on March 7, 1868, and was graduated in chemistry at the - Massachusetts Institute of Technology in 1891. In the same year he went to Pope's Island Manufacturing Co., at New Bedford, as chemist where he remained until 1895, where he became a teacher in chemistry at the Swain Free School, which position he retained until 1900. He then became chemist for the New Jersey Zinc Co., at Newark N. J., and in 1902 went to the Coe Brass branch at Torrington, Conn., as Chemist. In 1903 he became chief chemist and metallurgist and since 1912 has been technical superintendent and metallurgist of the American Brass Co., with head- quarters at Waterbury, Conn.

Jan 1, 1924

By C. J. McHargue, J. C. Ogle

Lightly deformed columbiun single crystals which contained only parallel hoins or purullel and intersecting trains were annealed at 1000' and 1600"C. No re-crystallizntion occurred in specimens hawing only parallel twins. Only noncoherent twin boundaries nzipated at 1000°C but both coherent and noncoherent ones moved al 1600°C. Recrystallization occurred within a few minutes at twin intersections at 1000°C. The orientation 01 the recrystallized grains differed front that of both the matrix and deformation twins, but could he derired by (110) and/or(112) rotations. ALTHOUGH twinning in metals has been extensively studied, there have been no definitive studies of the annealing behavior of crystals containing deformation twins. Some effects observed after annealing deformation twins have been summarized by Cahn1 and Hall2. Any or all of these phenomena are observed: 1) The twins may contract so that the sharp edges of the lens become blunted, and eventually the twin may disappear entirely. 2) The twins may balloon out at an edge, giving rise to a large grain having the same orientation as the twin. 3) The specimen may recrystallize; i.e., new grains are nucleated and grow at the expense of the twins and the crystal immediately adjoining the twin. Such grains have orientations which are not present before. Contraction has been observed in iron,3 titanium,3, 4 beryllium,5 zinc,8, 7 Fe-A1 alloy,' and uranium.9 Long anneals at high temperatures are required to have any appreciable effect in these metals and only thin twins are absorbed. Lens-shaped twins are absorbed from the edges: the thin, almost parallel-sided twins are usually punctured in several places and each piece contracts independently. Absorption is very gradual and no sudden cooperative jumps have been observed. The expansion of a twin into a larger grain of identical orientation is unusual, but such growth has been observed in iron,"'" zinc,6 and uranium." Crystals which have been deformed simultaneously by slip and twinning recrystallize first in the area adjacent to the twin. New grains appear faster where the twins intersect: but isolated twins, especially if thick, can also give rise to new grains. This type of recrystallization occurs in zinc.6, 7, 12, 13 and beryllium.14 Reed-Hill noted, in a single crystal of magnesium, the nucleation of a recrystallized grain at a twin intersection which had the same orientation as the second-order twin and which grew into the highly strained matrix.15 Short-time annealing has been reported to cause no change in the deformation twins in vanadium,16 columbium, 17, 18 tantalum,19 tungsten,'' and zinc.7 The purpose of this investigation was to note the effects of annealing on the coherent and noncoherent boundaries of deformation twins in columbium and to locate the nucleating sites for recrystallization. The orientation relationships, which the new recrystallized grains have with the parent crystal and the deformation twins, were also determined. EXPERIMENTAL PROCEDURE Single crystals of columbium were obtained by cutting large grains from electron-beam-melted buttons which contained 10 to 50 ppm C, 10 to 100 ppm O,, 1 to 10 ppm H2, and 10 to 15 ppm N2. The crystals were hand-ground and chemically polished until all grain boundaries were removed. The specimens were mounted in an epoxy resin and a face of each crystal was mechanically polished on a Syntron polisher using Linde A and then Linde B polishing compounds. After all faces were mechanically polished, the crystal was electrolytically polished to remove all distortion due to cutting and grinding. Laue photographs were taken of all faces of the crystals to determine the quality and orientation of each crystal. The crystals were compressed about 10 pct at -196 C in a specially constructed compression cage with an Instron tensile machine. Each crystal was separated from the top and bottom anvils by teflon films which acted as a lubricant. With the specimen crystal in position, the entire cage was cooled to -196°C by being submerged in a Dewar containing liquid nitrogen. The crystals were compressed at a rate of 0.02 in. per min and the load was recorded on a strip-chart recorder. After deformation the crystals were mechanically polished on 600-grit paper and Pellon cloth with Linde A and Linde B polishing compounds. The crystal faces were chemically polished and then etched. The twin planes were identified metallographically from an analysis of the twin traces on two surfaces. Annealing was carried out by placing each crystal in a columbium bucket made from the same electron-beam-melted material as the crystal itself and suspending the bucket by a tantalum wire in a quartz tube. After a vacuum of 10-7 Torr was attained, a furnace at 1000" or 1600 C was raised into position and the crystals held for various lengths of time. The crystals were repolished and etched after annealing to remove any surface contamination. Approximately 0.010 in. was removed during this process. The resulting surface was examined metallographically for microstructural changes due to annealing. A microbeam Laue camera mounted on a Hilger Micro-focus X-ray unit was used to determine the Orientstions of the recrystallized grains. This X-ray micro-beam camera had a 0.002-in.-diam collimator and incorporated the ideas of both and and chisWik21 and Cahn.22

Jan 1, 1967

By R. W. Jenkins

TRACKLESS equipment is being used by the Coplay Cement Manufacturing Co. to develop a folded limestone deposit economically and safely with inexperienced men. Cost and quality of development stone results in a saving when it is used in- stead of outside sources of limestone. This favorable cost has been attained by following a methods development and training program described in this paper. It is expected that further savings in favor of the mined stone will be made when stopes now being prepared are in production. The present equipment will be used for loading from stope draw points. The limestone is blended with quarried cement rock to serve as raw material for Portland cement, first produced in this country by Coplay Cement Manufacturing Co. from a process developed by its president, David 0. Saylor, in 1873. For many years the cement rock alone or with a small amount of added limestone was used for raw materials. Later as specifications were raised and the richer portions of quarries were depleted, limestone from outside sources was required in increasing amounts. In 1925 D. J. Uhle, the general manager, began to prospect company property for limestone.

Jan 1, 1954

By F. H. Deily, Jean M. Quets, Milton E. Wadsworth, John R. 222-000-000-012 Lewis, D. S. Rowley, R. J. Howe

Samples of synthetic magnetite were reduced in hydrogen-water vapor atmospheres in the temperature range 450o to 900oC. The reaction was always surface controlled, indicating the final products of reaction are nonfirotective. Three separate cases have been identified from the kinetic results: Case I, reduction of magnetite to iron below 570°C; Case II, reduction of magnetite to iron above 570°C; and Case 111, reduction of magnetite to wustite above 570 oC. In Cases I and 111 the kinetics have been explained by the formation of oxygen anion vacancies in the magnetite surface followed by associated diffusional processes. In Case 11 the observed kinetics have been related to the concentration of iron cation vacancies in the wustite layer formed, followed by associated steady-state diffusional processes. The concentration of cation vacancies in the wustite is maintained constant by the magnetite-wustite equilibrium. THE reduction of the oxides of iron has been a subject of study and interest for many years. However, few attempts have been made to interpret the results in terms of the mechanism of reduction of an iron oxide by either hydrogen or carbon monoxide. Stalhane and Malmberg' using CO, H2, and CO-Hz mixtures, developed the rate expression: where m = mass of oxide reduced, t = time, k = a constant, s = surface area, P = partial pressure of of CO or H,, and P, = partial pressure of the reducing gas at equilibrium. The rate of reaction per unit area was proportional to the difference between the partial pressure of the reducing gas and its pressure at equilibrium. Hansen, Bitsianes, and Joseph2 studied the reduction of pellets of hematite to magnetite with mixtures of CO-CO,. They concluded that below 450°C the reaction proceeded according to a model in which CO reacts with the hematite surface producing an oxygen ion vacancy. The rate controlling step was then assumed to be oxygen ion diffusion through vacancies resulting in the formation of magnetite. They derived an expression giving the rate of reduction proportional to the cO/CO, ratio. Recently McKewan3 published results for the reduction of magnetite spheres in atmospheres below 570°C. He explained his results by an equation of the form where K, is the equilibrium constant for wustite-iron equilibrium attributed to the formation of wustite as an intermediate in the reduction of magnetite. According to McKewan, Kp is an equilibrium constant for H, -HO adsorption in which oxygen is deposited on the surface from the H,Oand subsequently acts as a poison for reduction by hydrogen. Sample Preparation and Experiments. In this work the authors used the same apparatus and experimental procedure employed in the hydrogen reduction of magnetite. Sintered disk samples weighing approximately 1.5 g and measuring 1.2 cm in diameter and 0.25 cm in thickness were prepared by a method described previously.4 Partial pressures of hydrogen and water vapor were controlled by bubbling hydrogen through a series of flasks containing distilled and deionized water maintained at constant temperature in an oil bath. The total flow rate of the reacting gases—hydrogen and water vapor—was approximately 0.5 liter per min. The entire external system was maintained at a temperature above the oil bath to prevent condensation of water vapor. This was accomplished by wrapping electrical resistance elements over all surfaces. The glass column containing the weighing system-a McBain balance suspended from a gold chain-was enclosed in an aluminum tube heated by nichrome resistance wire enclosed in an insulating material. The temperature of the glass column was held constant by means of a series of thermocouples connected in parallel to a Leeds and Northrup temperature controller. This was necessary since variations in temperature resulted in expansion and contraction of the glass column and could be readily observed with the cathetometer. The spring extensions were measured through a window with a gaertner cathe-

Jan 1, 1962

By M. H. Merriss

In the last few years, there have been developed at the plant of the Nichols Copper Co., Laurel Hill, 'Borough of Queens, New York City, improvements in electrolytic copper refining by the series system that have materially increased the flexibility and economy of that system. The purpose of this paper is to discuss, as of interest to refiners and to those who have copper to refine, as well as to the engineering profession in general, the changes' that have taken place resulting in wider application and increased efficiency of the series system. Copper is electrolytically refined in two ways, which are spoken of as the "multiple system" and the "series system." In both systems, the electrolytic tanks are in series electrically. In the multiple system the electrodes in a single tank are in multiple or in parallel, thus: There are two important adaptations of the series process, one represented by the series electrolytic tank room at the Baltimore Copper, Smelting & Rolling Co., Baltimore, Md., and the other by that of the Nichols Copper Co.'s plant. At Baltimore, the anode is rolled to perfect

Jan 1, 1926