Search Documents

By Adam L. Wesner, A. C. Richardson

DURING World War II the demand for electrode carbon was greater than could be met by the supply of petroleum coke available for this use. It was believed that coke made from an extremely low-ash coal might be a suitable substitute for petroleum coke. Requirements for electrode carbon to be used for the production of aluminum are that the silicon plus iron content shall be not more than 0.14 pct of the coke. However, during the period when petroleum coke was in short supply, it appeared that relaxations of the specifications might be allowed to permit 0.4 pet iron plus silicon in the coke. For this work, the specifications were that the coal should contain less than 1 pet of ash, and the combined iron and silicon content of the coal should not exceed 0.28 pct. Heavy-liquid separations made on a number of coals showed that if certain size fractions of some coals were separated at low specific gravities the resulting float products would meet the required specifications. The objective of this work was to develop a continuous, commercially feasible process for producing low-ash coal. After consideration of various processes, the method chosen was a float-and-sink separation using a solution of calcium chloride as the separating medium. Eagle Seam coal was used for the experiments. The -10 +35 mesh fraction was found to be the most promising feed for producing the low-ash [ ] content coal. A batch of 30 tons of -3/8-in. coal was screened at 10 and 35 mesh; the yield of -10 +35 mesh was 20 pct of the feed. This fraction comprised the feed for the separation tests. In spite of the fact that this portion was screened a second time at 35 mesh, the coal still contained 16 pct that was finer than 35 mesh. Three-fourths of the undersize was in the -35 +48 mesh range. A representative portion of the -10 +35 mesh fraction was subjected to batch float-and-sink separations to determine the best gravity to be used in the continuous tests to obtain a high recovery of low-ash content coal. The heavy liquid used was a mixture of carbon tetrachloride and benzene which assured complete wetting of all of the particles. As usual in batch separations, adequate time was allowed for each separation so that even the near gravity particles had ample time to separate. The separations were made at increments of 0.01 sp gr from 1.25 to 1.28 and also at 1.32 and 1.59. Each specific-gravity increment was assayed for ash content. From these data it was concluded that 1.27 sp gr was best for the continuous separation of the coal. The products from the batch separation were composited into float 1.27 and sink 1.27 sp-gr fractions; these were assayed for ash, iron, and silicon. Table I shows the results of the batch separations. The composite float 1.27 fraction contained 66.04 pct of the total weight, and had an analysis of 0.79 pet ash, 0.073 pct iron, and 0.112 pct silicon, or 0.185 pct iron and silicon combined. These data are indicative of the results possible if a perfect separation is made at 1.27 sp gr under static conditions. Inasmuch as the method under investigation is a dynamic system these results could not be obtained. It remained to be determined, however, just how close to the theoretical results the actual continuous separation would be.

Jan 1, 1952

By D. W. Fuerstenau, P. C. Kapur

The kinetics of green pelletization in a laboratory balling drum have been studied, using pulverized limestone as a model system. The growth characteristics of green pellets were found to be extremely sensitive to the moisture content of the material. Empirical kinetic equations, which incorporate a function of specific surface of the pellets as the criterion for growth potential, have been found to describe growth in a nucleation region and in a ball growth region. The rate constants in the kinetic equations are strongly dependent on the moisture content of the material being pelletized. Size distributions of the balls at different stages of pelletiz-ing are also discussed. In many industrial chemical processes, particulate matter can only be utilized if it is in an agglomerated form, such as pellets. Pelletizing is now widely used in iron ore technology1, and it has also been applied to a number of diverse fields such as the production of cement-kiln feed2, fertilizers3, and fluorspar4. Recently, it has been proposed to pelletize dispersion-type ceramic nuclear fuel elements5. In iron ore technology, for example, the production of agglomerates by pelletizing involves two major steps: 1) the preparation of green balls by rolling particles in a suitable balling device and 2) the firing of the green balls to form compact, strong bodies upon sintering. The critical step in a successful iron ore pelletizing operation is generally considered to be the balling operation1. In this paper, which is not concerned with the sintering of green pellets, the words green pelletizing and balling will be used interchangeably. Green pelletizing, or balling, will be defined as the process of forming larger bodies by rolling fine particles on a surface without the application of direct pressure. Two recent literature surveys6" indicate that in spite of the considerable amount of industrial pelletizing, very little is known about the fundamental principles of balling and its kinetics. The first reported research on the kinetics of pelletizing is the work of Newitt and Conway-Jones8. Using silica sands of different sizes in a batch laboratory balling drum, they found that the average green pellet diameter increased linearly with time at constant drum speed, and qualitatively the growth rate increased with moisture content. Generalized conclusions cannot be drawn from their research since the materials which they pelletized were sand and sand-silt mixtures rather than comminuted materials. Moreover, Newitt and Conway-Jones used testing sieves to estimate the size distribution of the green pellets, and this technique limited the range over which they could study the growth kinetics of the pellets. Bhrany and co-workers9 investigated the kinetics of balling iron ore fines on disk pelletizers ranging in diam from 1 to 18 ft. In their investigation, balling was carried out as a continuous operation, and growth kinetics were studied in terms of retention time of the material on the disk. Although the feed material in their study was quite coarse (the maximum size being about 1/2 in.), they also found qualitative relationships between pellet growth and water content, and feed size. In the present investigation, a number of innovations were introduced that refined the experimental measurements and established the reproducibility of balling experimentation. This enabled extension of the range of measurements to include study of agglomerate nucleation phenomena in the fractional mm size. This paper presents a detailed analysis of the nucleation and growth of green pellets in a laboratory balling drum. MATERIALS AND METHOD Pulverized limestone of specific gravity 2.72 was used as a model system in these studies. It has already been established that the balling characteristics of limestone and silica are similar to those of iron ore concentrates 2,8,10, depending on physical, rather than chemical, properties of the particles. The size distribution of the limestone was determined by a wet-dry sieving technique in the sieve range and by a sedimentation balance in the sub-sieve range. Fig. 1 presents the size distribution of the limestone used in this research. This figure shows that the material is finer than 200p (65 mesh) and that 25% of it is finer than 12. The specific surface area of this powder, as measured by BET gas adsorption methods,

Jan 1, 1964

COAL is perennially -a subject of major interest at. Pittsburgh, but during the week of Nov. 19 to 24 it was especially to the fore because nearly two thousand persons gathered to take part in the second of the international conferences organized by President Baker of the Carnegie Institute. From the opening session on Monday morning when those attending were welcomed by President Baker and T. P. Gaylord, president of the Chamber of Commerce of Pittsburgh, until the party returned from the Clairton coke ovens on Saturday. afternoon, there was something going on all the time, and usually three sessions were in progress at once.

Jan 1, 1928

Discussion of the paper of LAWRENCE ADDICKS, presented at the Salt Lake meet-ing, August, 1914, and printed in Bulletin No. 91, July, 1914, pp. 1671 to 1674. JAMES H. PAYNE, Baltimore, Md. (communication to the Secretary*). -Mr. Addicks's account of the behavior of the nodulizer at Chrome on blast-furnace flue dust leads me to outline what has been done so far upon the application .of the same apparatus to fine sulphide concentrates. As Mr. Addicks states in his paper, the conditions prevailing in the test kiln at Yorktown in the demonstration I made for him upon Chrome material were strongly oxidizing; so much so that the sulphur was roasted down to less than 1 per cent. It is therefore to be expected that the first test made upon sulphide ore a short time after this, in which Ducktown green ore fines were used, did not show very promising results. Although the Ducktown ore contained only 13.52 per cent. of sulphur its gangue was quite fusible, and the intense heat generated by the oxidation of. the extremely fine sulphide particles slagged the mass, bringing about a condition approximating that of a Brückner roaster in distress. During the spring and summer of 1912, the writer kept working upon different schemes to cut clown this slagging. Two successful methods were finally worked 'out embodying opposite principles, one promoting oxidation of the finer particles and the other retarding. their oxidation. In the early part of the present year the writer succeeded in interesting the Braden Copper Co. in nodulizing, with the result that an extensive series of tests were made at Yorktown upon oil-floated concentrates covering quite a wide range in analysis. These tests led to trials in the Chrome rotary on the part of the U. S. Metals Refining Co. of Minerals Separation concentrates which they had in stock, and later to test runs to check up the Yorktown runs on Braden concentrates. The large-scale tests checked up with the Yorktown tests in every way (except fuel consumption, which was, however, correctly predicted), and led to the Braden company's decision to adopt the process at Braden. The fuel consumption upon oil-floated concentrates is not over 6 gal. per ton and in many cases is less. The action in the furnace is independent of the sulphur content, and there is actually less tendency to form nose rings in the Chrome rotary than upon flue dust. It is believed that the improvements entering into the design of the Braden kilns will cut down the nose-ring trouble to where it will no longer be a drawback to the process.

Jan 11, 1914

By O. M. TUPPER

REQUIRING a finer ground clay than that obtainable with a dry pan or hammer mill, the Clay Corporation of California installed a five-roller, low- side Raymond impact mill at its Lincoln plant in 1925 and since then has been economically grinding fire clay with a moisture content as high as 15 per cent. This was one of the first, if not the first, of this type of mill to be used in the grinding of clay on the Pacific coast. The pulverizer consists of a die-ring, lying in a horizontal plane, enclosed in a sheet-iron housing. A vertical shaft supports a spider from which five rolls are suspended in such a way as to always have them bearing on the die-ring. The vertical mill shaft is driven by means of beveled gear and pinion from a horizontal shaft which is connected by belt with a 60-hp. motor with suitable pulleys to give a speed of 175 r.p.m. A large fan which has a speed of 1100 r.p.m. and is belt connected to a 40-hp. motor is connected to the mill housing. The discharge end of the fan is in turn connected to a cyclone dust collector.

Jan 1, 1929

By T. D. Tiemann

The extraction of iron oxide from several types of siliceous iron ore by digestion in sulfuric acid solutions was investigated in the temperature range from 80 to 258°F at concentrations from 10-60% H2SO4. Degree and rate of extraction were found to be critical with respect to both temperature and acid concentration, requiring temperatures in excess of 250° F and acid concentrations of 50% to effect 80-90% extraction of iron oxide in 60 min. Rate of extraction is directly related to surface area and apparently controlled by the rate of chemical reaction. The activation energy was found to be approximately 25,000 cal per g mol. Extraction characteristics of the several ores were found to be similar. The Department of Minerals and Metals Engineering at the University of Wisconsin conducts a continuing research program to develop processes for the utilization of low-grade iron ore deposits such as the nonmagnetic taconites of the Wisconsin Gogebic range. Methods under study include high-intensity magnetic and high-tension electrical concentration, flotation, direct reduction and chemical extraction. Concentration of a number of low-grade siliceous iron ores by the extraction of silica in sodium hydroxide solutions has been reported by the writer and others in the literature.1,2,3,4 Residual concentrates containing as much as 65% iron have been obtained from taconites containing less than 30%. Currently an alternative approach is under study, namely the dissolution of iron oxides from siliceous gangue by extraction in acid, with subsequent recovery of the iron from solution. Such a process for extracting iron oxide from the low-grade oclitic deposits of Alberta with hydrochloric acid was investigated and described by Gravenor, Govett and Rigg.5 The current investigation, which is entirely devoted to extraction with sulfuric acid, is the subject of this paper. In part, the objective of this research was to determine the possibility of leaching iron ores in situ with sulfuric acid. The investigation of a recovery method is left to later research. The ores investigated contained hematite (Fe2O3) as the principal iron-bearing mineral and minor amounts of goethite (Fe2O3 .H2O), magnetite (Fe3O4), and iron-bearing silicates. The gangue was essentially quartz occurring as single crystals and microcrystalline aggregates. Detailed description of the ores may be found in the literature.1,2,4,6 A comparison of the specific ores used in this investigation is shown in the partial analyses of Table I. EXPERIMENTAL METHODS All extractions were made at atmospheric pressure using beakers with a mechanical stirrer for those tests run below the boiling point, and Erlenmeyer flasks for those at the boiling point. A thermostatically controlled hot plate was used for heating, and this maintained the mean temperature within the solution to within ±3°F during extraction. The sample of ore for extraction was weighed to + 0.02 g. For tests below the boiling point, the sample was added to the beaker containing the sulfuric acid solution at the desired temperature. For the boiling-point tests, the sample was added to the Erlenmeyer flask followed by distilled water and the

Jan 1, 1968

By B. J. Scheiner, A. G. Smelley

The Bureau of Mines, US Department of the Interior, is conducting research on a dewatering technique for fine particles generated during the mineral beneficiation process that will recover a portion of the water now being lost using conventional waste disposal methods and significantly reduce the time required for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong stable flocs that can be dewatered rapidly on static and/or rotary screens. Infield tests, phosphate clay waste has been dewatered from a nominal 2.5% solids to greater than 20% solids. In other field tests, coal-clay waste has been dewatered from a nominal 3% solids to greater than 55% solids. In addition, small-scale continuous tests have shown that bentonitic clays can be dewatered from 12% solids to 40% solids.

Jan 1, 1985

By J. E. Spruiell, F. H. Patterson, B. F. Shuler

The microstructures and textures developed by the working of high-purzly thermochemically deposited tungstem sheet have been inuesligated. Greater than 60 pct reduction was required to deslroy the columnar grain structure which existed in the as-deposited sheet. With increasing reductions the texture gradu-ally charged from the initial as-deposited orientation with (100) parallel to the sheet normal to a (100}(011) ideal ovienlation with some spread about the rolling direction. This texture was retained after recrystalli-zation a1 2000°C. THE processes for depositing tungsten by hydrogen reduction of tungsten hexafluoride have been under development for the past several years.1,2 The nature of the deposition process is such that the as-deposited material contains a highly oriented columnar grain structure perpendicular to the deposition substrate. This well-defined columnar structure may be useful in certain applications293 but a wrought or equiaxed structure may be desired for some components such as tubing. Knowledge of the effects of working ther-mochemically deposited (TCD) tungsten is therefore necessary in order to establish the feasibility of obtaining worked and recrystallized microstructures and textures. The details of a recently developed technique for thermochemically depositing flat, uniformly thick tungsten sheet are presented with emphasis on the effects of deformation by rolling on the microstructure and texture. Although no work has been previously reported on the rolling and the annealing textures of TCD tungsten, there have been some determinations of textures for cold-rolled tungsten foil prepared from powder-metal -lurgy billets.4-8 The general description is that of a predominantly lurgy{100}(011) texture, with some spread about the rolling direction as an axis. pugh5 reports data both for cold-rolled and for annealed foil having about 96 pct initial cold work. He observed no change in texture, except for a decrease in the spread, for annealing treatments of 30 min at temperatures up to 1800°C. On annealing at 1900°C, both the low-temperature components plus new components which were described alternately as {001}(320) plus {001)(230) or as {100}(011) ± 12 deg about the sheet normal were observed. Above 1900°C, the new orientation existed alone, and it was stable up to 2500°C, the highest temperature that Pugh investigated. THERMOCHEMICAL DEPOSITION OF TUNGSTEN SHEET High-purity tungsten sheet was reproducibly deposited on the inner walls of a molybdenum mandrel by the thermochemical reaction WFs(g) + 3H2(g) - W(s) + 6HF(g). The mandrel was heated by a five-zone tube furnace which afforded a controllable fixed-temperature profile. Sheets measuring 1+ by 12 in. have been deposited with uniform thicknesses of up to 0.145 m. As shown schematically in Fig. 1, the purified reaction gases were metered into a mixing chamber at a Hz-to-WF6 ratio of 15 and preheated to 350°C. The flow rate of the WF6 was 300 cu cm per min at stp. These gases were directed through a conical injector into the deposition chamber. Inside this chamber hydrogen reduction of the WF6 to pure tungsten metal occurred on the hot walls of the molybdenum mandrel at a total pressure of 5 Torr. Typical temperatures for the five zones in the chamber were, respectively, 565", 540", 550°, 570°, and 590°C. The hydrogen fluorlde generated from the reaction, the excess hydrogen, and some un-reacted WF6 were pumped on through the scavenger

Jan 1, 1968

By Grant Buma

The purpose of this paper is to present arguments and evidence that there are natural processes at work which tend to minimize the impact of solution mining on the environment. The contaminants have two sources. First are elements which were present in the roll-front deposit in insoluble compounds, for example, uranium in uraninite and coffinite, molybdenum, arsenic, iron, cobalt, nickel, etc. in sulfide minerals, vanadium in micas and clays, etc. Second are elements introduced by the leach liquor. Precipitation of reduced compounds, scavenging of heavy elements and absorption by quartz and clays, can all reduce the amount of heavy elements in solution. If a roll can be demonstrated to be actively precipitating uranium and heavy metal elements, then the presence of precipitants (pyrite and carbon) can be assumed. Criteria for recognizing an active roll are described.

Jan 1, 1979

By Bernard G. Carbajal

The dielectric properties and thermal stability of glow-discharge polytnerized films of styrene, chloro-benzene, and other organics and photoresist filrns are presented. Variations in the glow-discharge polymerization procedure are related to thermal stability. Thermal treatwzents to improve the dielectric properties of both positive (A2 340) and negative (KMER) photoresists are given. THIS study of the dielectric properties of thin organic polymer films is part of a program to investigate the electronic applications of organic materials. Thin organic polymer films have been produced in an ac glow discharge,13 with a low-energy electron-beam process,4 and in an rf dicharge. A process has been developed during the course of this program for forming thin organic polymer films in a dc glow discharge. These glow-discharge polymerized (GDP) films exhibit some useful dielectric and insulative properties. Variations in the properties of the GDP films can be induced by changes in the source material (monomer) andor in the conditions of the glow discharge. Thin organic polymer films can also be produced from typical positive and negative photoresists. Some variations in the properties of the photoresist films can be induced by suitable post-application treatments such as thermal crosslinking. The properties of interest in this study are dielectric constant, dielectric strength, resistivity, and thermal stability. POLYMER FILM PREPARATION I) GDP Films. The GDP films were prepared in a dc glow discharge in an atmosphere of organic monomer vapor. The details of the glow-discharge procedure have been presented previously.6 Briefly, under the influence of a dc glow discharge organic vapors can be polymerized in the vapor phase and the resultant polymer (GDP film) deposits on and in the vicinity of the cathode. Substrates placed behind a screen cathode can be uniformly coated over all exposed areas. Pattern definition can be achieved using normal mask stencil techniques. Table I presents the pertinent parameters in the preparation of GDP styrene. Conditions of Forrrzation of GDP Styrene. The rate of deposition for GDP films was monitored using a current-time integrator. The thickness of the deposited film for a given set of experimental conditions was a function of the current-time integral. The fifth row in Table I is a compilation of the deposition rate of GDP styrene films. Other organic monomers behave in a similar fashion. With the exception of the highly halogenated saturated hydrocarbons, all organics subjected to the conditions of the glow discharge form GDP films. 11) Photoresist Films. Photoresists are normally recognized to exist in two forms, a low molecular weight, soluble polymer form (A) and a high molecular weight, crosslinked insoluble form (B). Typical negative photoresists are applied in the low molecular weight form A and converted to the high molecular weight form B by the action of light. (Positive photoresists are applied in form B and converted to form A by the action of light.) Eastman Kodak Metal Etch Resist (KMER) has been chosen as a typical negative photoresist. Polymer film samples were prepared in the same configuration used for GDP films. The KMER was applied in the usual fashion using a 120°C drying step (infrared-lamp heating) and a 180°C post-bake. Care must be taken to completely remove the solvent in the drying step and to properly develop and postbake to exposed photoresist. If the photoresist film is not properly dried and postbaked, severe blistering and peeling will occur during subsequent elevated-temperature exposure. Thickness can be controlled by varying the viscosity of the form A photoresist and the spin rate at application. AZ 340 was chosen as a typical positive photore-

Jan 1, 1967

By J. E. Lawrence

Copper-decorated lattice disorders in silicon have been analyzed by electron transmission microscopy, chemical etching, and P-N junction reverse current measurements before and following different gettering treatments. Lattice disorders acted as the nucleating sites for copper precipitation. Copper precipitates in silicon resist chemical etching, absorb electron beams more than silicon, and cause excess reverse currents. Totally gettered disorders will chemically etch rapidly, be transparent to electron beams at extinction contrast, and not contribute to excess reverse currents. Three different gettering procedures were performed to determine the effectiveness of different EXTRANEOUS metal contamination can alter the minority carrier lifetime and resistivity of bulk silicon as well as cause excessive reverse currents in semiconductor devices. Previous workers have reported such activity for gold,1,2 copper,'-* iron,' and rnanganese.2,5 Gettering is a method employed to render these impurities electrically inactive. However, some property of the junction-degrading metals prevents gettering procedures from being wholly reliable. The comparative effectiveness of gettering with different agents has been the topic of earlier publications.2,3,6-11 Two mechanisms for gettering metallic impurities have been proposed: the distribution coefficient mechanism by Thurmond and Logan7 and the compound formation mechanism by Goetzberger and Shockley.2 Both of these models evolved from data gettering mechanisms. First, phosphorus was allowed to enter a protective SiO2 film but remain away from the Si-SiO2 interface to test the effectiveness of the compound formation gettering mechanism. Second, phosphorus was allowed to enter the backside of silicon wafers to test the effectiveness of the lattice strain gettering mechanism. Finally, nickel was diffused into the backside of silicon wafers to test the effectiveness of the distribution coefficient gettering mechanism. In each case, copper precipitates dissolved as a result of the gettering treatment. Tightly packed precipitates will resist gettering more than loosely packed copper precipitates. acquired by the electrical analyses of gettered semiconductor materials. An electrical analysis, however, cannot identify the fate of the gettered metals. The radiotracer technique has recently been applied to determine the redistribution of metals following different gettering treatments.3,9,10 The spatial resolu tion of the radiotracer technique prevented the analysis of metal precipitates which contribute to the excessive reverse currents of P-N junctions. The gettering processes employed by the earlier workers, almost without exception, allowed the gettering agent to enter the silicon lattice. This procedure makes it quite difficult to differentiate between the distribution coefficient and the compound formation mechanisms. The metallographic analysis of gettered copper precipitates discussed in this work supplements the earlier work by obtaining direct evidence of silicon lattice defects decorated with copper before and following different gettering treatments. The effectiveness of a process which restricts the gettering agent, phosphorus, to a dielectric film and thus away from the silicon lattice is discussed in addition to the ef-

Jan 1, 1969

By Irving Cadoff, Richard Nolder

An analysis oj a series of samples of single -crystal silicon grown on sapphire shows that ,four distinct orientation relations exist. There are at least thirteen crystallographic planes which serve as substrates ,for epitaxial growth The model which assumes that silicon substitutes for aluminium and bonds with the oxygen atoms of the sapphire to form the first later for subsequent growth can account for the epitaxial geometry in all four cases. Multiplici-ties 01 specific orientations are found which are explained by the symmetry of both the sapphire and silicon crystal structures. It was reported in the previous paper' that single-crystal silicon films can be deposited on single-crystal a A1,03 (sapphire) with a wide variety of orientations. The silicon films, however, were found to deposit in only four different orientation relationships with respect to the sapphire substrate. The X-ray data have been analyzed to determine the plane and direction of atomic fit and an atomic model to account for the epitaxial relationships at the silicon-sapphire interface has been developed. These results are described in the present paper. EXPERIMENTAL The Laue X-ray data described in the previous paper were reduced to stereographic projections in a standard manner. These data were supplemented with X-ray reflection data obtained with -& E and A Full-Circle Goniometer (Electronics and Alloys, Inc.) mounted on a Phillips diffractometer unit. The silicon films were thin enough to result in characteristic reflections from the substrate as well as the silicon. The superimposed stereographic projections were analyzed to determine the orientation relationships. Ambiguities were resolved by referring to constructed models of various lattice planes for both silicon and sapphire. These lattice models were also used to develop the model for atom fit at the interface. DATA AND ANALYSIS 1) Crystal Structures. The crystallography of silico-n, which is of the diamond cubic class with a. = 5.4~, is straightforward. The sapphire structure is more complex and generally difficult to represent in pictorial form. It is of the rhombohedra1 class but usually referred to hexagonal axes. The transformation of indices between these two systems can lead to ambiguities which will have bearing on the analysis presented herein. Therefore, the basis used in this paper is described in the appendix. Referred to the hexagonal system, the parameters of sapphire are co = 12.95.&, a, = 4.75~, c/a = 2.73. All parameters are for room temperature. Figs. 1 and 2 illustrate schematically the hexagonal unit cell model of sapphire used for this analysis. The oxygen atoms are assumed to occupy positions in an idealized hexagonal array on basal planes. Their actual positions are in a slightly distorted hexagonal array. The aluminum-atom positions are scaled to their actual positions in the lattice with respect to the basal layers of oxygen atoms. It was found that an idealized model where the aluminum atoms are assumed to lie exactly at the octahedral interstices of the oxygen lattice, similar to that used by ~ronberg,' was not adequate for this study.

Jan 1, 1965

By Karl F. Peterson, H. K. Najarian, Robert E. Lund

PRIMARY products of the Josephtown smelter are zinc metal of various grades, lead-free zinc oxide pigments, cadmium metal, and sulphuric acid. Zinc concentrates of domestic and foreign origin are blended and desulphurized at the roaster plant. The equipment includes five, 12-hearth Herreshoff roasters and two modified Trail-type suspension roasters. The sulphur dioxide containing gases from the roasting operation are diverted to a four-unit contact acid plant for the manufacture of sulphuric acid. The roasted calcines are agglomerated by sintering on Dwight-Lloyd-type sintering machines; the sinter is crushed and sized within required limits; and the sized sinter is smelted in vertical shaft-type electro-thermic furnaces. Of the 13 electrothermic furnaces of various sizes now in operation, four are designed to produce American process zinc oxidc of various specifications; and the remaining nine furnaces are equipped with vacuum-type condensers and produce zinc metal. Papers describing the general smelting practice at Josephtown have been published by AIME. Since both High Grade zinc metal and lead-free zinc oxide pigments are produced direct from the electrothermic furnaces without need for subsequent refining, the elimination of impurities such as lead and cadmium has to be accomplished during roasting and sintering operations. To effect the producing of both High Grade and Prime Western zinc products, the roasting and sintering operations are on two separate circuits. A High Grade circuit produces finished sized sinter low in lead, cadmium, etc., for the High Grade furnaces; and the Prime Western circuit produces finished sinter destined for the furnaces producing Prime Western metal. Sintering at the Josephtown smelter differs in many important respects from the sintering practice in smelters operating horizontal retort zinc furnaces. Requirements of the electrothermic smelting furnaces define the physical characteristics of the sinter, while the chemical composition of the sinter is controlled according to the grade of metal and oxide to be made as final products. Three principal objectives in the sintering process at Josephtown smelter are: 1. To transform the zinc calcine from the roasting operations into a hard, yet porous agglomerate that will not crumble in the smelting furnace. 2. Crushing and sizing of the sinter to obtain a proper screen analysis which is normally —% in. down to +1/4 in. particle size. 3. To eliminate, particularly in the High Grade circuit, as much of the impurities such as sulphur, lead, and cadmium as possible. The sintering plant as originally built in 1930 was equipped with three standard 42 in. x 44 ft Dwight-Lloyd sintering machines. Each machine was equipped with a 15x60 in. sintering corporation fan driven by 150 hp, 900 rpm synchronous motor through a magnetic clutch and capable of delivering 30,000 cfm of air at 15 in. of water and 150°F. Each sintering machine was driven by 7½ hp dc motor with controllers for varying the speed of the machine from 8 to 32 in. per min. The pallets were cast iron and the grates of the herringbone type. The charge was mixed in a 4 ft diam x 8 ft Stehli pugmill and transported by belt conveyor, elevator and tripper conveyor to a small bin over each machine. Shortly after the start of operations the following changes were found necessary: 1. The herringbone grates which plugged very quickly and were difficult to keep clean were replaced by straight, narrow cast-iron grate bars running at right angles to the travel of the pallets. These grate bars are held in place by a center bar extending across the pallet on the 24 in. dimension and by removable retaining plates which form the sides of the pallets. 2. Mechanical grate knockers were developed in conjunction with new grate bars for continuously and automatically cleaning the grates. 3. As the cast-iron pallets cracked, they were replaced with cast-steel pallets. In 1938, the capacity of the sinter plant was increased with the installation of two 42 in. x 22 ft machines which were brought from the company's Herculaneum lead smelter. With a circulating load of some 250 to 300 pct, production of finished sinter on the 42 in. x 44 ft machines at this time amounted to about three tons of sized sinter per machine hour. In 1945, one of the 42 in. x 22 ft machines was replaced by a 60 in. x 44 ft machine of our own design. In 1948, as part of the plant-wide expansion program, the sinter plant not only was expanded but also divided into two separate plants; namely, Prime Western and High Grade circuits. The sinter destined for furnaces producing Prime Western zinc metal is made in a new plant comprising two 60 in. x 44 ft Dwight-Lloyd-type sintering machines, each having a 45,000 cfm Sturtevant fan at 18 in. water static pressure and served by an 8 ft diam x 12 ft long rotary charge pclletizer and auxiliary crushing and sizing equipment. The sinter destined for furnaces producing High Grade zinc metal and zinc oxide pigments is produced in the old sinter plant which was expanded to accommodate four of the 60 in. x 44 ft sintering machines, replacing the old sintering units. In the High Grade sinter circuit, two units of the 60 in. x 44 ft machines are used as preliminary soft sinter machines; and the remaining two units of the 60 in. x 44 ft machines are used to make finished hard sinter. Purification Theory Partial elimination of lead and cadmium in the sintering of zinc ores is common knowledge. However, by some manipulation and by taking advantage of the double circuit, it is possible to make zinc sinter which is nearly free of contaminators. Lead

Jan 1, 1952

By William J. Potter, Roger N. Pyle

Introduction The primary ingredient for survival of mining companies during a recessionary period is to be innovative and resourceful in the structuring and financing of operations. Over the past decade, many mining companies have had to retrench and restructure their operations and to redeploy their assets just to survive. During the same period, traditional sources of financing for mining companies -- commercial banks, subsidized export credit loans and long term straight debt financing in the public markets -- became less available and more expensive. Meanwhile, new markets and new financing instruments provided new alternatives for mining companies. Those companies which exploited these alternatives greatly enhanced their capacity for survival and even for profitability. This article considers the strategies adopted by some companies to adapt to changes in this recessionary environment; the inadequacy of traditional sources of financing; certain of the new financing instruments, structures and markets which have become available; and how several mining companies have utilized these new instruments, structures and financial markets to improve their competitive positions. THE IMPACT OF RECESSION ON MINING COMPANIES AND TRADITIONAL FINANCING SOURCES In its 1983 year-end article "The New Economic Order" Mining Journal characterized many of the large private sector mining companies with operations in the industrialized countries as being "gripped between the jaws of high working costs and stagnating metal commodity prices." The article went on to characterize the Canadian mining industry in particular as being "in the difficult position of having to seek to sell the bulk of its output in a world market characterized by over-capacity, where production costs were determined by internal political and economic factors while prices were set by external competitive forces of supply and demand." Miners of a wide range of commodities in the industrialized countries have come to realize that their domestic mineral resources are in many cases no longer competitive with global sources of supply. To compete and survive they would have to rely on their technical and financial expertise in mineral exploration and development and in mining and processing. Strategies For Survival Global competition has compelled management in the extractive industries to improve their worldwide cost position. This is the only means whereby a mining company can differentiate its product and attain a substantial competitive advantage. During the past decade, for example, ASARCO Inc. and Inco Ltd. chopped their payrolls, postponed expansion plans and otherwise retrenched. ASARCO reduced its capital expenditures and cash requirements for operations in 1984 to a level almost equal to its internally generated cash. The company's finances were also strengthened by increasing total lines of credit from outside sources, by selling common stock, and by reducing annual pension funding through a change in actuarial assumptions. Other companies returned to their traditional organizational structure where they had a demonstrated competitive strength. Consolidated Gold Fields, for instance, resumed its operation as a mining finance house. Its capital investment programs are now devoted solely to resource development. In mid-1984, at a time of firming zinc prices, Union Miniere S.A. used the opportunity to integrate its smelting capacity and to direct investment to certain subsidiaries at the expense of less viable operations. Smaller corporations realized that it was not enough just to be the low-cost producer. For example, Drummond Coal Company in Alabama, which dominates its regional market due to its low-costs, has also developed a world-wide trading capability and has placed incremental tonnage from its own mines as well as brokered coal produced by others, thereby minimizing capital risk. In Canada, Campbell Resources has exploited difficult times by acquiring assets cheaply. In the process it improved its capacity to withstand cyclical economic swings by diversifying from solely a copper and gold producer to a company based upon asbestos, coal, copper, gold and natural gas.

Jan 1, 1985

By R. J. Pfister

The development of a water-input profile instrument based on the introduction of brine and fresh water into an input well with the electrical location of, the boundary developed between them is reported. Two methods are available in the use of this instrument to measure the foot by foot water-intake rates of the various sand strata: the moving boundary method in which variable well bore diameters can be determined and/or cancelled out and the constant boundary method. The type of results obtained and the relative advantages of each of these methods are described in detail. Representative data are included covering the use of this instrument in experiments involving selective acidizing, selective plugging, and selective shooting. In such experiments, this instrument has been used to diagnose the unfavorable distribution of water intake in input wells and also to determine the effectiveness of the resultant treatments. The data included also serve to illustrate the type of problems which can be studied with this technique. Introduction For ten years or perhaps longer a number of progressive water-flood operators have felt the need for some to to measure the foot by foot water-intake rates of various strata in water-injection wells. The primary need is to diagnose unfavorable water distribution in various strata and to evaluate the effectiveness of the corrective measures such as selective acidizing, selective plugging, and selective shooting. Previously described methods for obtaining this type of data were not considered entirely adequate.l,2 The profile equipment described in this paper embodies the separate introduction of brine and fresh water into the well at carefully measured and controlled rates and the electrical location of a sharp boundary developed between these fluids. At present this instrument is a research tool of value in determining the effect of various well treatments on an individual sand strata. lts primary use has been on wells in which different sections require different treatments (e.g., wells with an open sand to be plugged and a tight sand to be acidized)- It has, thus, made possible the determination of a rearrangement of the water intake of a well. The instrument can also be used to direct the treating material into a given zone. In completing a well the less permeable sands are shot more heavily with nitroglycerine in order to equalize the water intake between the permeable and less permeable sands. The extent to which such corrective shooting has been successful Can be determined by a water-input profile. The combined profile and well-bore diameters should also provide a method for determining the direction and effect of various selective shooting techniques. Equipment The essentials of the water-input profile technique for measuring the intake per foot of individual sand strata are the injection of a nonconducting fluid, water, at the top of the well and a conducting fluid, brine, through a separate string of

Jan 1, 1948

By R. J. Pfister

The development of a water-input profile instrument based on the introduction of brine and fresh water into an input well with the electrical location of, the boundary developed between them is reported. Two methods are available in the use of this instrument to measure the foot by foot water-intake rates of the various sand strata: the moving boundary method in which variable well bore diameters can be determined and/or cancelled out and the constant boundary method. The type of results obtained and the relative advantages of each of these methods are described in detail. Representative data are included covering the use of this instrument in experiments involving selective acidizing, selective plugging, and selective shooting. In such experiments, this instrument has been used to diagnose the unfavorable distribution of water intake in input wells and also to determine the effectiveness of the resultant treatments. The data included also serve to illustrate the type of problems which can be studied with this technique. Introduction For ten years or perhaps longer a number of progressive water-flood operators have felt the need for some to to measure the foot by foot water-intake rates of various strata in water-injection wells. The primary need is to diagnose unfavorable water distribution in various strata and to evaluate the effectiveness of the corrective measures such as selective acidizing, selective plugging, and selective shooting. Previously described methods for obtaining this type of data were not considered entirely adequate.l,2 The profile equipment described in this paper embodies the separate introduction of brine and fresh water into the well at carefully measured and controlled rates and the electrical location of a sharp boundary developed between these fluids. At present this instrument is a research tool of value in determining the effect of various well treatments on an individual sand strata. lts primary use has been on wells in which different sections require different treatments (e.g., wells with an open sand to be plugged and a tight sand to be acidized)- It has, thus, made possible the determination of a rearrangement of the water intake of a well. The instrument can also be used to direct the treating material into a given zone. In completing a well the less permeable sands are shot more heavily with nitroglycerine in order to equalize the water intake between the permeable and less permeable sands. The extent to which such corrective shooting has been successful Can be determined by a water-input profile. The combined profile and well-bore diameters should also provide a method for determining the direction and effect of various selective shooting techniques. Equipment The essentials of the water-input profile technique for measuring the intake per foot of individual sand strata are the injection of a nonconducting fluid, water, at the top of the well and a conducting fluid, brine, through a separate string of

Jan 1, 1948

By P. G. Linder

The mechanical concentration of ores has not attained any considerable extent in Sweden, by reason of a scarcity of ores calling for this kind of treatment. Of rich iron-ores there is still an abundant supply; and magnetic concentration, which in the future undoubtedly will become of great importance, not being as yet demanded by necessity, has not advanced beyond a few experiments. At the copper-mines mechanical concentration has been superseded by chemical processes; the lead mines are worked out; and it is (with one exception) only the mines producing blende, or blende and galena intimately mixed, that have adopted mechanical methods for enriching their low-grade ores. While the concentrating-plants in Sweden are few and their output is comparatively insignificant, the methods employed, the general features of the work and the results obtained under extremely unfavorable conditions, may offer some points of interest to persons who are engaged in this branch of industry and have similar problems to deal with. Before going into a detailed description of the several plants, I will offer a few remarks that hold good for all of them and constitute a general review of Swedish concentration and its conditions. At all the works the ore to be treated is a mixture of blende and

Jan 1, 1895

By Robin O. Williams

The increase in internal energy as the result of deformation has been measured for lead, aluminum, silver, nickel, iron, and zirconium by using rapid, adiabatic compression. The stored energy increase is roughly Proportional to the strain; the propor-tionality constant increases rapidly with increasing melting point. The fraction of the mechanical energy which is stored increases more slowly, since the strength of the metals also increases with melting point. The values of the stored energy are considered accurate to about 10 pet. The present values appear about 50 pet larger than the more reliable published results where comparisons are possible. It is possible that this difference is due to the high strain rate used in this investigation. Immediately after deformation all these metals release energy at a rate roughly proportional to (time)-'. This release is considered to be associated with dislocation motion but in aluminum (and copper) some additional process seems to be present. This release can represent 20 pet or more of the stored energy. WHEN pure metals are plastically deformed, most of the mechanical energy is converted into heat. The energy remaining within the metal is significant in that it is the energy of the disorder produced and thus detailed knowledge of this energy is a powerful tool in understanding the nature of deformational disorder. While much effort has been expended on this problem, the amount of information available is limited. The situation as of 1958 has been carefully reviewed by Titchener and ever.' The present results have been obtained by a new experimental approach to this problem. The method necessitates high-strain rates which make comparisons with published results less certain, but a high-strain rate is an advantage in that the energy release immediately after deformation can be followed. EXPERIMENTAL PROCEDURE In the experimental method used, the internal (stored) energy is given as the difference between the mechanical work used in deforming the sample and the heat which is released (the first law of thermodynamics). The work is supplied by two identical hammers swinging freely from a fixed height, the available energy being the product of the mass, the gravitational constant, and the distance through which the center of gravity moves. The initial temperature rise of the sample represents the heat produced by the deformation. The sample temperature is determined by a small thermocouple embedded in and supporting the sample. This process can be repeated over and over to produce increased strains. Most samples are run through about five cycles to a total strain of around 0.7. Further details are covered elsewhere. The determination of the heat is dependent upon the sample weight, its specific heat, the rise in temperature, and any gains or losses to the surroundings. One is dependent on published results for specific heals (the values were taken from a collection).3 The values must be accurate to about 0.1 pet in order that they not affect the results. The best values thus do not contribute to the uncertainty, but this is probably not always the case. The accuracy of the temperature rise is limited primarily by knowledge of the thermocouple characteristics over short temperature intervals, but careful calibration eliminates this as an important factor. One can calculate readily the heat flow between the sample and hammers if the time of contact and the sample temperature are known and if there were no oil at the interface. Assuming the maximum temperature difference, upper values for this interchange have been calculated (the time of contact is determined from the decrease in sample length) and it may or may not be significant. However, no correction is colnsidered necessary because of the presence of a thin oil film which has a thermal conductivity much less than the metals. Except for the possible uncertainty in specific heat, the heat is considered to be adequately known. The mechitnical losses which are recognized as important are: 1) friction between the sample and the hammer:;, 2) the kinetic energy in the hammer suspension system which may not be entirely usable, 3) the rebound energy of the hammers, and 4) the vibration of the hammer heads. All these have been covered in detail elsewhere2 and only the more significant points are made here. The friction turns out to be small except for soft materials (lead)

Jan 1, 1962

By B. G. D. Smart

An understanding of the nature of yield zones surrounding coal mine excavations is fundamental to the design of mine support systems. Various methods have been designed for investigation of underground rock masses and an extensometric technique, the Magnetic Rod Extensometer, has been developed to overcome inherent design limitations in existing equipment of this type. This paper refers to the prototype form of the extensometer and details changes designed to overcome a variety of drawbacks indicated by routine use of the equipment. The principal change has been one of manual to computerised data acquisition and presentation in the laboratory phase of the system. This has dramatically reduced the time taken to process underground measurements and produce numerical and graphical results. The revised Magnetic Rod Extensometer represents an integrated instrumentation system that combines speed and accuracy in all areas of data handling.

Jan 1, 1984

By John Griffen

Methods of coal preparation in England, including usage of American units such as the Chance sand flotation process and Denver flotation cells, are compared with methods used in the United States. Problems of the coal industry in Holland are summarized.

Jan 2, 1951