Search Documents

By J. B. Macelwane

Historically whenever application of scientific results to a new problem required the special experimental background, the economic outlook and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering based on the professional requirement grew up in the engineering colleges. This is precisely what is happening now in geophysical engineering. THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1953

By O. N. Carlson, S. A. Bradford

Discontinuous yielding in tensile tests was observed in V-O alloys in the temperature ranges of 150° to 175°C and also 350° to 400°C. The magnitude and intensity of the serrations were found to vary considerably with oxygen content. Maxima were observed in tensile and yield strengths and in the strain-hardening coefficient at the higher temperature only. The strain rate sensitivity was observed to be negative between 150° and 400°C. THIS investigation was undertaken to study the effect of oxygen on the tensile properties of iodide vanadium in the temperature range of 25o to 450°C. Brown1 observed an increase in strength between room temperature and 400°C in vanadium metal, and found that oxygen and nitrogen had a rather pronounced effect on the strength and ductility. A maximum in the tensile strength was observed by Rostoker et al.2 near 300oC and by Pugh3 around 450°C for calcium-reduced vanadium. Pugh also found a maximum in the yield strength and in the strain-hardening exponent, and minima in the elongation and strain rate sensitivity at the same temperature. Eustice and Carlson4 reported the appearance of serrations in the stress-strain curves between 140° and 180°C in iodide vanadium containing 600 ppm O. These anomalies in the mechanical properties indicate that strain aging occurs in vanadium, but the impurity or impurities responsible for the above-mentioned effects have not been identified. The phenomenon of strain aging is usually characterized by the return of the yield point after interruption of a strength test. In the temperature range where strain aging occurs, the yield and tensile strengths attain maximum values, elongation and strain rate sensitivity exhibit minima, and discontinuous yielding is generally observed in the stress-strain curve. Cottrell5, 6 has postulated that strain aging is due to the migration of solute atoms to dislocation sites to produce locking after the dislocations have broken free from their impurity atmospheres during the initial yielding. At the strain-aging temperature the process is a dynamic one in which the solute impurity atoms diffuse to the vicinity of the moving disloca- tion producing "locking" which gives rise to maxima in the tensile strength and serrations in the elongation curves. Cottrel17 has noted that discontinuous yielding in iron occurs when the diffusion coefficient of nitrogen, D, and the strain rate, i, are related by D = 10-9 €. EXPERTMENTAL PROCEDURE The vanadium metal employed in this study was prepared by the iodide refining process as described by Carlson and owen.8 A representative analysis of the vanadium used in this investigation was: 150 ppm O, <5 ppm N, <1 ppm H, 150 ppm C, 150 ppm Fe, 70 ppm Cr, <50 ppm Si, 30ppm Cu, 20 ppm Ni, <20 ppm Ca, <20 ppm Mg and <20 ppm Ti. Alloys containing from 200 to 1800 ppm O, all of which lie in the solid solution range of the V-O system, were prepared by arc melting vanadium together with portions of a high-oxygen master alloy. The master alloy was prepared by tamping pure V2O5 into holes drilled in a vanadium ingot and arc melting this five or six times in an inert gas atmosphere, inverting the button between each melting step. The oxygen content of the master alloy was then determined by vacuum fusion analysis. Vanadium containing less than 150 ppm O was prepared in the following manner. A bar of iodide vanadium was deoxidized by sealing it in a tantalum crucible with a few grams of high-purity calcium. This was held at 1100°C for 4 days to allow time for the oxygen to diffuse to the surface and to react with the calcium vapors. The calcium oxide product was later dissolved from the surface of the bar with dilute acetic acid. In this way vanadium containing from 20 to 50 ppm O was prepared. Sample Preparation. The are-melted ingots were cold swaged into 3/16-in. diam rods and these were machined into cylindrical tensile specimens with a reduced section of 1.00-in. length and 0.120-in. diam. The test specimens were annealed for 4 hr at 900°C in a dynamic vacuum of mm of Hg to remove hydrogen from the metal. This recrystal-lization treatment produced a uniformly fine-grained structure with a mean grain size of approximately 0.06-mm diam. The oxygen contents reported in this paper were determined by a vacuum fusion analysis of the tensile specimens after testing. Analyses for other interstitial or metallic impurities showed no significant changes from that of the original material. Tension Tests. Tension tests were performed on a screw-driven tensile machine at a constant cross-head speed of 0.01 in. per min. Tests at elevated temperatures were carried out by heating the

Jan 1, 1962

By Charles Hart

THE art of electric smelting came with the turn of the present century and owes its existence to the introduction of alter-nating current, which found its first wide use in the establishment of the great power plants at Niagara Falls, N, Y. Prior to that time current was largely direct. The fur-naces were electrolytic in nature and found their first metallurgical use in the produc-tion of aluminum, and this process still prevails. The normal production of pig iron up to that time was carried on in blast furnaces in which charcoal, coke and anthracite were used as the fuel. This new electric process called for sufficient carbonaceous material to reduce the oxides and impregnate the pig iron with sufficient carbon, but the remainder of the energy was to be supplied by electric power. The chemical reactions are essentially the same in electric smelting as obtains in the older blast furnace. All of these data are so well known in both methods as to need no discussion at this time, for they can be found in scientific publications and books written during the first two decades of this century.

Jan 1, 1940

By E. Ackerman, L. Y. Tu, S. C. Sun

The use of ultrasonics in forming emulsions is not new. As early as 1927 Wood and Loomis&apos; reported preparation of emulsions with ultrasonics. In 1935 Rschevkin and Ostrawskyz described the use of great ultrasonic power in producing fine emulsions of various oils and paraffin in water. Recently Oyama and Tanakahmployed ultra-emulsification to increase the effectiveness of sodium ethyl xanthate in flotation of chalcopyrite and galena. An emulsion is a two-phase system consisting of two incompletely miscible liquids, the one being dispersed as finite droplets in the other. The dispersed liquid is known as the internal or discontinuous phase, and the surrounding liquid is termed the external or continuous phase. There are two types of emulsions; one is oil-in-water (O/W) and the other water-in-oil (W/O). The word oil refers to the liquid other than water. Circumstances exist in which the emulsion type is not clearly defined, and the internal and external phases both contain portions of the opposite phase. This is said to be a dual emulsion. Among the many hypotheses&apos;, 6v proposed for the formation of emulsions, the Bancroft&apos;s adsorbed film or double interfacial tension theory is widely accepted. Bancroft ""educed that in the process of emulsification the interfacial tension between oil and water is lowered by the formation of an emulsifying film, which contains the adsorbed molecules and/or ions from the emulsifying agent and the two liquids.

Jul 1, 1955

By R. W. Gurry

WHEN a steel in the austenitic state, with all its carbon in solution, is maintained, at constant temperature, in contact with a gas that removes the carbon from the surface, yet without otherwise altering the composition of the steel, the change in weight of the specimen, after any period of exposure, is a direct measure of the amount of carbon it has then lost. The purpose of the present paper is to show how, by application of established mathematical reasoning based on the fundamental diffusion law and on certain postulates, this loss of weight yields a complete picture of the distribution of carbon throughout a specimen of regular shape after any period of exposure, with all the accuracy required in any practical occurrence of decarburization. Precisely the same is true for the gain in weight during the reverse process of carburization, or for the gradual gain or loss of any element, so long as the steel comprises only a single phase at temperature, provided always that the experimental conditions conform to the postulates. The change in carbon content from surface to center of the specimen is always continuous, when everything is in solution, even though under the microscope the decarburized zone (or carburized rim) may appear to be sharply defined. The experimental procedure is described and some typical results are presented, which are then interpreted by application of the diffusion law. EXPERIMENTAL PROCEDURE Initially an endeavor was made to follow the gain of weight during the process of carburization in a hydrogen-toluene atmosphere, but it was soon found that the specimen became coated with graphite, which could not be removed without some loss of metal; therefore it was decided to continue carburization until the steel was saturated throughout, to remove all graphite from the surface of the specimen, and then to follow the loss of weight during decarburization in a moist hydrogen atmosphere at the same temperature as that used for carburizing. The carburizing procedure has been described in an earlier paper;1 it suffices to state here that the carburization lasted about 140 hr. at 760°C. (1760°F.) and 44 hr. at 1110°C. (2030°F.), these periods being long enough-on the basis of the calculations presented later-to ensure that the specimen was about 99.9 per cent saturated at each temperature. The specimen was a cylinder about 3.8 cm. long and 0.475 cm. in diameter; the materials were carbonyl iron, a commercial low-metalloid iron, and a steel with 3.6 per cent nickel and the usual proportion of other elements. The fully carburized specimen, after cooling at the top of the furnace tube, was placed in a lathe and sandpapered to remove all graphite; then the diameter was measured with a micrometer caliper, and the initial weighing (corresponding to complete saturation) was made. By means of a

Jan 1, 1942

By C. H. Samans, G. F. Tisinai

HARDENING and embrittlement of the ferritic chromium stainless steels at temperatures near 885 °F have been known for a long time.&apos; However, no satisfactory explanation has been given. Both ordering and precipitation hardening have been suggested. Fisher, Dulis, and Carroll2 discovered a chromium-rich body-centered-cubic precipitate in embrittled alloys. Subsequently, Williams&apos; and Wright4 also have found evidence of this body-centered-cubic constituent. William&apos;s hardness, electrical resistance, and magnetic studies led to his proposal of a new constitutional diagram for the Fe-Cr alloys. The new feature of this diagram is the eutec-toidal decomposition, below about 970°F, of the s phase into two stable body-centered-cubic solid solutions, one rich in iron and the other rich in chromium. An observation of Heger5 that the amount of s phase has increased and the amount of chromium-rich body-centered-cubic phase decreased in the interval 5000 to 32,600 hr at 900°F, even though the alloy increased in hardness, casts some doubt on this diagram. If precipitation hardening causes the embrittlement, the precipitate probably is always coherent with the matrix, since no evidence of overaging has been reported. It cannot be stated positively, however, that Fisher&apos;s body-centered-cubic constituent is the embrittling phase. According to Preston&apos;s data,6 such a chromium-rich phase should have a parameter less than about 0.5 pct larger than that of the iron-rich matrix lattice. Moreover, the constitutional relationships whereby Fisher&apos;s constituent forms, and whether it is stable, metastable, or a transition phase, are not yet completely clear. The recent studies of Wright4 and of Lommel,7 as well as the earlier studies of Becket8 and of Hochmann,9 have shown that 885°F hardening occurs in relatively pure Fe-Cr alloys. No evidence of its occurrence or absence in chromium itself has been reported. The rate of hardening in high purity alloys seems appreciably slower than that in alloys containing larger amounts of impurities (chiefly carbon and nitrogen). This may be due merely to the absence of hardening and straining effects from precipitated carbides and/or nitrides. These observations on high purity alloys make it seem unlikely that 885 °F hardening is caused by a constituent containing other than iron and chromium atoms, e.g., carbides and/or nitrides. Wright,4 Lommel,7 and Lena and Hawkes10 emonstrated the accelerating effects of a finely dispersed precipitate of (probably) chromium nitride on the hardening reaction. This appears to be evidence that lattice straining increases the rate of nucleation of the hardening constituent. Some new observations on 885°F hardening are reported here. They show an effect of preheat treatment that should contribute to a better understanding of the 885°F hardening phenomenon. They also clarify a discrepancy which exists in the literature. Some investigators have reported most rapid hardening at 885", whereas others have reported it at 930°F. The present work also shows that 885°F hardening does not occur in electrolytic chromium, and that any long range ordering type of reaction affecting any sizeable part of the volume is unlikely. Materials Studied Table I shows the currlposition of the alloys used in this investigation. In these alloys carbon and nitrogen are present in roughly similar amounts. Presumably both elements precipitate, as carbides and/or nitrides, during the heat treatments given.

Jan 1, 1958

By M. C. Flemings, A. A. Tzavaras

Analytical and experimental procedures are descrihed for quantitative determination of volume-fraction microporosity in metals by mimorarlio-graphg. The analysis assumes spherical pores but allows for the observed fact that pores or portions of pores smaller than a given thickness do not project an image on the film. Volume-fraction microporosity was measuured in cast low-alloy steel and shown to vary from 0.6 x 10-4 to 10 x 10 depending on mode of solidification and on whether the material was air- or vacuum-cast. The aim of work described herein was to develop a method of quantitative measurement of the volume fraction of microporosity in cast metals. Microporosity, present in nearly all castings and ingots, is always interdendritic in nature and may be large enough to be seen on a polished surface with the naked eye. More generally, it is smaller in size, and its detection more difficult. Three techniques might be considered for measurement of microporosity: 1) lineal analysis of a polished metallographic surface, 2) density measurement, or 3) quantitative microradiography. As will be shown later, volume fractions of porosity in directionally solidified castings may be the order of 10-4 to 10-3; such small amounts of porosity are difficult to identify and measure on a polished surface. Density measurement is also not a suitable technique (for alloys) when the volume fraction of porosity is low. This is because the density of the base metal is often not known within the necessary accuracy, due to microsegregation or partial phase transformations. In general, it is not possible to completely eliminate microsegregation without also altering the porosity. Because of the limitations of the foregoing techniques, quantitative microradiography was employed to determine amount of porosity. In recent work, microradiography has been found to be useful for qualitative measurement of porosity, including determination of size and shape of individual pores;&apos;)&apos; however, quantitative determination of amount of porosity has not been attempted. I) CALCULATION OF VOLUME-FRACTION POROSITY The following analysis employs procedures similar to those of Cahn and Nutting3 and Hilliard.4 Major simplifications are that pores are assumed to be spherical and to be present in sufficiently small quantities that no overlapping occurs. A basic difference from the previous treatments is that the limited "sensitivity" of microradiography is considered. Assume first 1) cavities are spherical and of uniform diameter, 2) cavities are randomly distributed, 3) volume-fraction porosity and specimen thickness to pore radius ratio are sufficiently small that overlapping of the projected images of cavities is negligible, 4) sensitivity is limited (i.e., holes or portions of holes of less than a given thickness do not project an image on the film). The sensitivity, is defined as: where 5 = minimum thickness of void from which an image will be projected on the film and t = specimen thickness. Now, from Fig. 1, it is possible to distinguish between two different types of holes. These are 1) holes whose centers lie within the region t/2 > X > 6/2, where X is distance from one surface of the specimen (positive into the specimen), and 2) holes whose centers lie within the region (6 — r) < X < 6/2, Holes whose centers lie outside X = (6 -r) project no image on the film. These two types of pores are considered separately below. Type 1 Pores. When 6 is greater than 0, the image of a spherical cavity of radius r appears on the film as a circle of radius a which is smaller than r. From geometry, Fig. 1: a2=r2-52/4 [2] where a = radius of image of pore on film and r = radius of pore. Since the pores are randomly distributed and spherical V =4/3pr2Nv [3] where V = volume fraction of voids and Nv = number of pores per unit volume and the number of images of Type 1 pores per unit area of film, N&apos;A, is

Jan 1, 1965

By B. Ehgartner, M. Karmis, C. Haycocks

INTRODUCTION Interaction effects between mining operations developed on different levels of contiguously placed bedded deposits are a major problem in many parts of the United States. Efficient design criteria, derived from careful analysis of field studies as well as theoretical and model analysis, have shown that many problems that may result from seam interaction can be avoided, minimized, or on occasion used with beneficial results. Selection of seam mining sequence is rarely based only on ground control considerations, but rather on factors such as seam ownership, characteristics and accessibility. Therefore all possible mining sequences and methods must be considered in the development of multi-seam design criteria. Increased utilization of the longwall method of mining creates special problems in multi-seam mining due to the inevitability of caving and, therefore, subsidence. Considerable valuable experience has been gained in this direction from British mining operations where interaction problems are extremely common and the longwall method is the primary method used. However, limitations persist in the application of much of this information to U.S. conditions due to variation in layouts between advancing and retreating longwall systems and the inherent difference in the geologic environment. Considerable field data is available for U.S. room and pillar operations, and where successful pillaring operations have been carried out close parallels may be drawn with ground control mechanisms in longwall operations. VARIABLES AFFECTING INTERACTION Analysis of ground control multi-seam problems shows that factors contributing to interaction may be classified into variables that are fixed by the geo- logic environment and those that depend on engineering design. These may be described as follows (Haycocks et al, 1982): Fixed: (i) Depth*, (ii) Innerburden thickness*, (iii) Innerburden physical characteristics*, (iv) Stress field, (v) Seam thickness, (vi) Coal characteristics, (vii) Completed mining operations either above or below the seam to ve mined, and (viii) Age of workings. Mining: (i) Height, (ii) Dimensions and geometry*, (iii) Method*, and (iv) Spatial location of entries* *These variables are regarded as being critical effects. Few attempts have been made to quantify the variables controlling interaction. Dunham&apos;s (1978) linear regression analysis, combined with the National Coal Board&apos;s MRDE Roadway Monogram, is probably the most noteworthy. This study involved eighteen multi- seam longwall mines in the United Kingdom. The following variables were taken into account: seam depth, pillar width, opening shape, floor and roof conditions, rate of face advance, vertical seam interval, and age and geometry of overlying workings. A multi-linear regression analysis of these variables fitted by appropriate field values developed a prediction equation for lower seam stability. Although the study included many variables, it neglected the nature or geology of the innerburden. The prediction equation was found unreliable, but it did show the significance of geometry as a factor controlling lower seam stability. MINING SEQUENCES Irrespective of the type of mining method selected only four possible mining sequences are possible for two seams. Finlay and Winstanley wrote in 1934. .. "Experience has shown that whether the upper or lower seam was worked first, the subsequent working of the other seam in the same area seriously affected the roads in the seam first worked." Those effects depended upon the four basic mining sequences: 1) The upper seam is mined out prior to mining the underlying seam; i.e., the seams are mined sequentially downward and mining of the underlying seam is not commenced until operations above are completed and have ceased.

Jan 1, 1982

By Lewis Delano

IT HAS been generally recognized that, owing to the extreme friability of, galena, fine grinding has a tendency to cause excessive sliming of the mineral, so operators of lead mills have attempted to avoid this condition by commencing concentration at as coarse sizes as any mineral is freed. Jigging has been the basis of the milling process, making a clean coarse concentrate and a large amount of tailing, which was considered sufficiently low-grade to be rejected. However, developments and improvements in concentration processes are everywhere changing the low-grade tailing of yesterday into material worth retreating today. Investigations of the work of the Hancock jig on the Bonne Terre ore- have shown that the best results to be expected will give a tailing assaying 0.75 per cent. lead; the average over all conditions and grades of ore will be between .0.80 and 0.90 per cent. By crushing the jig tailings in ball-mills and retreating by tables and flotation, a tailing of considerably lower grade can be made; the problem then becomes an economic one of increased crushing costs versus higher recovery. In considering the entire elimination of jigging, the increased smelting charges; due to a greater amount of slime galena will be counterbalanced by the lower operating cost, in-creased recovery, and the many advantages of a simpler flow sheet. In developing these problems in the Bonne Terre mill of the&apos; St. Joseph Lead Co., a long series of tests has been carried out covering every stage of crushing and concentration, and a large number of possible flow sheets were considered and tried. Only the final results and a few comparisons will be given here. At the same time, a careful and detailed cost-keeping system has enabled us to compare milling costs with the various flow sheets, and to calculate the economics of the problem&apos; with great accuracy. .

Jan 8, 1920

By G. S. Cole, G. F. Bolling

ThE exact type of fluid flow which occurs in a solidifying ingot is important in determining subsequent grain structure. This has been shown in studies of natural Convection" and of forced stirring or other disturbances of the melt."16 We shall explicitly argue that a complement to the existing natural flow in an ingot should be more effective than other types of flow in promoting the columnar-to-equiaxed transition. The ultimate effects of fluid flow upon structure is one of the topics of solidification that we have investigated in the alloy system Pb-Sb, under conditions simulating casting. In Fig. 1, the essential features of a bidirectional growth apparatus are shown; horizontal freezing from water-cooled faces within a low-thermal-conductivity lavite boat is a reasonable simulation of an ingot section. Details such as the furnace and thermocouples are omitted in order to show the location of four permanent. magnets, each with a pole separation of 21 in. providing a central field of about 1000 Gauss. When coupled with a dc current imposed through appropriate connections made at the cooled faces, a flow of fluid is produced as shown schematically. This technique described by Pfann and ~orsi" is ideal for our purpose since the flow indicated is the same as that we observe to occur naturally in this system. Components of 99.999 pct purity were used for study and all due precautions were taken in alloy preparation to avoid contaminants. Sections of the specimens were taken to ensure results representative of the interior as well as the surface of specimens. All proportions of equiaxed and columnar regions were measured by tracing the etched grain structures onto graph paper and simply counting squares. Four alloys were examined at superheats of 40" * 5°C and 100" * 9°C. Preliminary tests had shown that no appreciable enhancement of structure was obtained with magnetic field alone, so that this condition is not reported; it should nevertheless be noted that other configurations of magnetic field will reduce convection and thus enhance columnar growth.&apos;8 For the tests reported the magnetic field was applied to a specimen by bringing the four preassembled magnets to a position 2 mm from an outer tube immediately after the ingot was poured. The dc current of 30 amps passed through the sample throughout the entire solidification cycle, resulting in a power dissipation of 9 w per sq cm of interface. This may be compared to the evolution of latent heat of approximately 18 w per sq cm. Table I contains the results of this experiment in terms of the total area ratio, equiaxed/columnar grains, as a function of the field interactions, solute concentrations, and superheats employed. The total structure of the ingot is seen to be most influenced when both the field and current are applied simultaneously; when current acts separately, little effect may be noted in spite of the heat supplied. In addition, the change in structure from the no field-no current case to the field-current condition is more pronounced at the higher superheat, and the higher the concentration of antimony. An example of the grain refinement, as well as the increased equiaxed zone, is shown in Fig. 2. It is now important to prove that there is indeed an increase in fluid flow due to the presence of the field-current interaction; this is done by temperature measurements in the liquid metal. Let us consider a bidirectional casting in which heat is applied to and removed from the system, in such a way that rate of solidification is zero.* When a sensitive thermocouple

Jan 1, 1967

By William R. Taylor

This paper reviews the mining and related legislation history of in situ uranium mining in southwest Texas with emphasis on the last five years. It also reviews the current regulatory process and some of the more critical concerns and concepts relative to containment and restoration of in situ mines.

Jan 1, 1979

By G. Willard Quick

FAILURES in railroad rails have been of vital concern to engineers; railroad executives, rail manufacturers and the general public for years. Failures from transverse fissures originating from internal nuclei have received particular attention in the past 20 years. Dr. J. E. Howard first reported this type of failure in 1911, as being responsible for a wreck-on the Lehigh Valley R. R. in which several lives were lost. Since then many transverse fissures have been found. In 1919, Waring and Hofammann1 etched longitudinal sections of rails in hot acid and found cracks extending both longitudinally and transversely in certain used rails as well as in some new rails.. Since then it has been thought by many that these "shatter" cracks are the nuclei from which transverse fissures subsequently develop in service. Methods for reducing the rate of cooling rails on the hot. bed have been devised to decrease the temperature gradient and consequently the stress gradient in the rails. A study of the tensile properties of rails at elevated temperatures was made by Freeman and Quick,2 who investigated the properties at temperatures through which rails pass on the cooling bed after leaving the hot saw. In their investigation a special study was made of the ductility of the steels in the temperature range 400° to 700° C. In this temperature range it was found that certain rail and other steels showed a marked decrease in elongation and reduction of area. The phenomenon was called "secondary brittleness" and the temperature range the "secondary brittle range." A tentative explanation was presented that internal failure such as "shatter cracks" and "hair cracks" in rails are the result of thermal stresses developed in the steel structure while cooling through the secondary brittle range. The investigation showed that the magnitude of the phenomenon varies for different heats, but that it did not differ for specimens from different ingots or for different rails in a particular ingot. It was also shown that annealing rail steel at a temperature either above or below the critical

Jan 1, 1932

By Peter Nalle

12.3-1. Reporting. NEED. It seems almost unnecessary to comment on the need for reporting research and development results and activities, and yet much of the difficulty and misunderstanding surrounding a Research and Development (R&D) group results from poor or nonexistent reporting. Certainly no evaluation can be made without reports of results or plans. It is as important to report accurately and fully for the department&apos;s own use as it is for external use. Research unreported might as well be considered research undone. This section will discuss, in part, the need for reporting, the general types of reports which may be generated to satisfy the need, and finally, the evaluation of a project as judged by various commonly used standards. PURPOSE. Some specific observations might be appropriate concerning the reporting of R&D results. The requirements and background of the group receiving the report must be considered. A particular report is usually directed towards the background of a particular group, such as ((technical," "operational," "financial," or "marketing." It is essential that the emphasis and coverage be geared to the training of people receiving the report. It should be obvious that the financial department will be less interested in the technical details of the process and more interested in the capital funds and tax implications involved in the project. Operating personnel will be greatly interested in the effects of a new method on mining plans, and so on. This does not mean that the reporting in any way should slight pertinent details, nor should a patronizing attitude be assumed by the writer. However, it is essential that the needs of the reader be recognized. For reports that might have large and varied distribution, it is often feasible to group, either as sections or appendixes, the special details and information of interest only to certain functions within the organization. A

Jan 1, 1968

By E. H. Crabtree

Research on the iron ranges begins to bear fruit in big plant construction -Big coppers raise capacity, build at new Arizona, Michigan, Nevada, properties - Hydrometallurgy comes to fore with new uranium ore treatment and the Chemico process for nonferrous metals -

Jan 2, 1953

By F. Kurata, P. C. Davis, T. L. Gore

An experimental method and apparatus for the study of the low-temperature phase and volumetric behavior of volatile mixtures are described. The phase diagrams, including the critical points, and the volumetric behavior of a natural gas and a mixture of the natural gas with methane at temperatures from -40°F to -200°F and pressures to 1.200 11si are givrn. INTRODUCTION Knowledge of the phase and volumetric behavior of mixtures of the light hydrocarbons at low temperatures is becoming increasingly important as interest in low-temperature separation processes increases. Distillation at low-lemperatures has been used for some time to recover ethane and ethylene from natural gas and refinery gas for petrochemical uses. Removal of excess nitrogen from natural gas by distillation has been proposed as a means of increasing the capacity of gas transmission lines and of improving the marketability of the gas.1,2 Evaluation of the latter process has been hampered, however, by the scarcity of data from which the phase behavior of natural gases at low temperatures might be predicted. While existing correlations of vaporization equilibrium constants may be used to predict the behavior of such mixtures at lower pressures, high-pressure computations often require knowledge of the location of the critical point of the system involved. Although correlations have been developed for the prediction of the critical temperature and pressure of certain types of hydrocar-bon systems, they do not apply to very volatile systems such as nitrogen-bear-ing natural gases. This paper describes the initial stages of an investigation of the low-temperature behavior of a numher of natural gases and other gases of commercial interest. The experimental method and apparatus are described. and the phase and volumetric behavior of a natural gas and a mixture of the natural gas with methane are presented. PREVIOUS WORK The published low-temperature vapor-liquid equilibrium data for hydrocarbons and mixtures of hydrocarbons with nitrogen and helium are listed in Table I. Most of these data are for binary systems, and the data of Stutz-man and Brown" at 100 psi are the only data on a natural gas. The data of Bloomer and Parent3 on the methafie-nitrogen system, which have been phblished since this study was completed, are a valuable addition to the knowledge in this field. Prior to the publication of these data the only published critical point data on systems having critical temperatures below the ice point were those of Ruhemann.1 on the methane-

Jan 1, 1952

By G. F. Comstock

THE subject of transverse fissures in steel rails has been discussed very thoroughly in recent years from various points of view and the final opinions expressed may be roughly classified into two groups: (1) That these fissures are the result merely of fatigue of the steel and are independent of the quality of the metal. (2) That the quality of the metal and the mill practice must have something to do with them. The first point of view was most-ably and logically presented by J. E. Howard,1 and in the discussion of this paper, as well as in several other preceding publications, Dr. P. H. Dudley, Consulting Engineer of the New York Central Lines, has strongly defended the other opinion.2 The steel makers of the country have naturally rallied under Mr. Howard&apos;s banner, hoping to place the entire blame for these. failures upon the railroads with their high wheel-loads, hard steel, heavy traffic, and sometimes inferior roach-bed; while the railroad men,, on the other hand, have been busy accumulating statistics and records in the effort to find an actual reason in the rails themselves that would account for the seemingly haphazard occurrence of transverse fissures under varying conditions and at widely separated points. The view that these fissures were due merely to normal fatigue under alternating stresses seemed most reasonable to the writer until quite recently, because from work clone in this laboratory, as well as the work of other investigators of the problem, no structural differences, in the vast majority of cases, were found between metal at the nuclei of transverse fissures and metal at similar positions in the same rails or in other rails that had not developed fissures. . Within the last year or two, however, since the method of etching polished sections for the microscope with a cupric chloride solution has been tried systematically. on lengthwise sections, passing through the nuclei of transverse fissures, evidence

Jan 11, 1918

By M. R. Geer, H. F. Yancey

John Grifien (Pittsburgh)—I wish to congratulate the authors on this paper, which, I am sure, will promote a clearer conception of the various criteria which have been advanced as measures of coal-cleaning performance. Their clear descriptions of the more important criteria that have been advanced and explanations of their meaning and application have been sorely needed and, if widely promulgated and followed, should remove much of the confusion which, heretofore, has been evident. I suggest that much of this confusion has also arisen from lack of common agreement as to the exact meaning of the words and terms used in our discussions of this subject. I am sure I have been equally guilty in this respect and suggest it is time that we select a committee to study vocabulary as well as criteria, so that common understanding and agreement can be had. Thus, I suggest, that the title of this paper should have used the words "coal-cleaning performance" and not "coal-washery performance." My understanding is that "washery" refers to a complete plant and it has additional functions to that of coal-cleaning, such as control of size, moisture, etc. Also, I do not agree with the authors that the formulas given in their paper, the Fraser and Yancey formulas, are necessarily the only ones that can be called efficiency formulas. When a dictionary is consulted one realizes that the words "efficiency" and "efficient" have not precise meanings but only very general ones and must be further defined for each particular use, if they are to have any precise meaning. To my mind, the first of the Fraser and Yancey formulas given should never be used as expressing "efficiency" alone but only by the fuller phrase which truly expresses the kind of efficiency it states, which is "coal recovery efficiency." For complete clarity we then need only define "coal" for the particular circumstances under which the formula is used. This would recognize the fact, fully explained by the authors, that the limits in coal qualities imposed by the market have imposed a factor—and a variable factor—which has influenced any answer obtained by this formula. Such a procedure makes it entirely practical and logical to use the values of any of the qualities of coal—ash, sulphur, phosphorus, specific gravity—or a combination of them to define what is coal for that particular use of the formula. Further, it is clear to me that the criteria to be used must be dictated by the objective in view and the use for which the data are obtained. The authors clearly point out that the Fraser and Yancey coal-recovery efficiency formula is influenced by three factors, "one is determined by the coal, one is dictated by market or use conditions, and one is an inherent characteristic of the cleaning unit itself." The formula which uses the inverse of misplaced material as a measure of efficiency is also a coal recovery efficiency formula and is influenced in like manner by these three factors. As the authors point out, both are useless in obtaining data which enables a direct and valid comparison of the performance of a given cleaning unit on two coals where the other two factors vary or of the performance of two or more cleaning units of different types unless the values of the other two factors are identical. Much of the confusion in our discussions of and literature on coal cleaning has come from failure to understand clearly this fact. Many such comparisons have been made from which erroneous conclusions have been drawn. I am, therefore, particularly glad to see the authors&apos; emphasis on 4?-1e criteria which indicate the "sharpness of separation. I feel that these are the essential criteria

Jan 1, 1952

By B. Ramaswami, Y. Nakada, R. Schaefer

EARLY investigations1 of the tensile properties of fcc single crystals did not reveal the easy glide region of crystals with axial orientations inside the standard stereographic triangle. With the production of high-purity metal, a region of easy glide became known1 Consequently, modern work of fcc single crystals ordinarily uses high-purity metal. In order to determine whether further purification of aluminum beyond 99.992 pct purity would result in significant alteration of the tensile properties of single-crystal specimens, metal was zone-refined and crystals grown from the purified material were compared to crystals grown from the original material. Some similar studies were made of gold and silver crystals. Aluminum. The material to be zone-refined was cast into bars 1/4 by 1/2 by 8 in. A zone, approximately 1-1/2 in. in length, was passed over each bar eighteen times at a rate of 6 in. per hr. Melting and stirring were carried out by an induction heater under a vacuum of approximately 10"5 mm Hg, the metal being held in a graphite container. he last 3 in. of each processed bar were then cut off and discarded. No quantitative determination of purity was made, but the effectiveness of the zone refining was tested by a method first suggested by Walton, Tiller, Rutter, and winegard3 depending on the relation between cell structure and impurity content. Rutter and Chalmers4 have shown that a cellular substructure is associated with the presence of impurities during solidificatibn, and have shown how solute rejection at the freezing interface can lead to such an association. Thus the observation of cells gives evidence of impurities being present. To look for cells, the last quarter of a zone-refined bar was cut off, remelted, and grown rapidly into a single crystal. It was then heavily electropolished and thermally etched.~ Cells were revealed by the presence of many parallel rows of etch pits. The same process was carried out with material from the first half of the bar, but no cells were detected. These observations give evidence that a significant amount of impurity material was moved to the "dirty" end of the zone-refined bars. Further indication of purification was obtained from recrystallization experiments. It was found that, after cold rolling to a 97 pct reduction in thickness, the material from the pure end of the bar re-crystallized at room temperature, but the material from the "dirty" end did not. Other investigators6 have previously reported that zone-refined aluminum recrystallized at room temperature. The purified material was cast into 1/4 by 1/4 in. bars, and seeded crystals were grown in a (100) orientation and in a single slip orientation where the Schmid factor is m =2. The crystals were then cut to the desired length, annealed for 24 hr at 610°C, furnace-cooled, and etched in Tucker&apos;s etch. The crystals were tested in a floor-model Instron machine, using a gage length of 4 in. and a strain rate of 1/2 pct per min. The resulting curves are shown in Fig. 1. It is seen that the differences between the curves for zone-refined and original-purity materials are small. These differences are within the scatter observed for crystals of the original purity. In particular, the zone refining does not significantly affect the onset of the different "stages" of the curves.

Jan 1, 1964

By J. E. Hilliard

AS is well-known, the length per unit volume, Lv, of any lineal feature (such as grain edges in a polycrys-talline specimen) can be estimated from a count of the number of point intersections with a random plane of polish. Specifically:&apos; Lv = 2NA in which NA is the expected number of intersections per unit area of the plane. As with all other measurements in quantitative metallography, the estimation of Lv is subject to a sampling error, the magnitude of which will depend on the number of observations. The analysis is usually performed by counting the number of intersections falling within a closed test figure of known area applied to a succession of different areas on the plane of polish. The test figure can be drawn directly on the screen of a projection microscope or else superimposed on the image of the structure by means of a reticule in a focusing eyepiece of an ordinary microscope. The use of micrographs is very inefficient unless, as in the present study, these are also needed for some other purpose. Consider an analysis in which n applications are made of a test figure within which the expected number of intersections is N. The expected total number of intersections counted is then given by NT = nN If (N) is the standard deviation in N for one application of the figure and if the latter is applied to non-overlapping regions so that the N&apos;s are independent in the statistical sense, then the standard deviation in Nt is given by: a(NT) = a(N)vn Eliminating n from Eqs. [2] and [3] we obtain: Thus, k will be a constant for a given specimen and test figure. From Eqs. [ I] and [4] we find As is to be expected, therefore, the fractional error in the estimation of Lv is inversely proportional to the square root of the total number of intersections counted. It is very desirable to have at least a rough estimate of k before starting an analysis, since it will then be possible to decide in advance by use of Eq. [5J how many counts should be made in order to achieve the desired accuracy in Lv. Without such information the investigator, unless lucky, will either do needless (and tedious) work or else obtain a result with too large an error. It is very easy to calculate k for the limiting case of N — 0, i.e., when the test figure is vanishingly small. In this case there is a negligible probability of two or more intersections falling within the figure. There are therefore only two possible outcomes: a count of one with a probability of, say, p and a zero count with a probability of (I-p). Thus and Therefore: We might expect k to depend on N and therefore on the size of the test figure. Such a dependence was observed2 in the analogous case involving the estimation of grain-boundary area per unit volume by a count of the number of intersections of a test circle with traces of the boundaries on the plane of polish. In this case the theoretical value of k at the limit N — 0 was 1.41. It was also predicted that k would display an initial sharp decrease with increasing N. Experimentally, k was observed to decrease to a value of 0.62 at N - 6 and thereafter remain approximately constant. Furthermore, the value of k for N > 6 was found to be insensitive to the form of the structure provided no pronounced anisotropy or grain-size variation was present. In order to determinewhether k would exhibit a similar dependence on N in the estimation of grain-

Jan 1, 1967

By A. E. Weissenborn

Current knowledge of the substantial resources of zinc that exist in northwestern Washington is reviewed. These zinc-lead deposits are all associated with the Kootenay Arc, a narrow arcuate belt of folded and faulted rocks that dominates the regional structure of Stevens and Pend Oreille Counties and adjacent parts of British Columbia. The deposits of the Arc are only part of a major lead-zinc silver metallogenic province that includes the deposits of the Coeur d&apos;Alene district and the famed Sullivan ore body of Kimberly, British Columbia. Most, but by no means all the zinc-lead deposits of the Kootenay Arc are in carbonate rocks. They occur in several stratigraphic units, and in different parts of the Arc are quite diverse in character. The deposits appear to have undergone a complex geologic history and have not necessarily all been formed at the same time or by the same geologic processes.

Jan 1, 1976