Search Documents

By A. M. Gaudin

The flotation process has been applied extensively in the mineral and chemical fields. This paper reveals results obtained by an exploration of an application to the biological field. In many ways this study was indeed an exploration since so many factors are different. In the mineral field, the particles, both those floated and those not floated, cover a wide range of sizes and shapes; in the biological field, the particles of one population are primarily of one or two sizes and one or two shapes. This identity in size and in shape gives biological systems the advantage of homogeneity. In the mineral field the particles may be as coarse as a millimeter; in the biological field the size may be a micron, or less. In the mineral field the particles may have a gravity several times that of water so that their apparent gravity is quite substantial. Microorganisms, on the other hand, may have a gravity so near that of the liquor that their settling velocity in the liquor is vanishingly small. These two facts conspire to make bubble-particle encounter in the pulp-body less likely. Finally, microorganisms are living, reproducing, and dying-all of which does not help the experimenter get a balance of materials. The analytical problems, too, are extraordinarily difficult, for the organisms can contain only elements that occur in their environment, although at a different level of concentration. The chemical composition of the surface of microorganisms is readily altered. In spite of these areas of difficulty, microorganisms can be floated to leave practically water-clear tailing, they can be floated from each other and, in fact, the same organism can be fractionated into a float that differs from the sink. SIZES AND SHAPES OF ORGANISMS Most ore pulps are described with reference to the percentage of the pulp that is fine enough to pass a 200-mesh sieve. Thus a copper-ore pulp may be 80% -200 mesh. Since 200 mesh equals 74 µ, a 2000-mesh particle would be 7.4 µ in diameter, and a 20,000-mesh particle would be 0.74 µ. The microorganisms with which this work is concerned are of the order of magnitude of 20,000 mesh. We have worked with Escherichia coli, the colon bacillus, Bacillus cereus, Bacillus subtilis, Bacillus megaterium, and Serratia marcescens. In some pioneer work, Dognonl,2 reported the use

Jan 1, 1962

By Paul A. Beck

IN several recent investigations1 ' considerable evidence was accumulated to show the predominance in various face-centered cubic metals of a certain relative orientation, corresponding to a rotation of 30" to, 40" around a [111] axis, between a matrix with a strong single orientation texture and grains growing in this matrix." This relative orientation was found to occur both in recrystallization and in coarsening, "secondary recrystallization", so that one is inclined to look for an explanation applicable in both cases. The abundance of growing grains in the described orientations proves that suitable "nuclei" are present in the matrix material and that they have the capacity to grow. The scarcity of growing grains in other orientations may be explained in one 'of two ways. Either the number of nuclei or the rate of growth must decrease strongly for orientations deviating from that predominating among the growing grains, Fig. 1. Both the "oriented nucleation" and the "oriented growth" theory found support in the literature. Because the frequency of nuclei as a function of orientation is in most instances not amenable to direct experimental investigation, a definitive decision is difficult to achieve. However, it is now known with great certainty that the rate of boundary migration is strongly dependent on the relative orientation of the two grains meeting at the boundary and that the orientation favored by high boundary mobility closely corresponds to that predominating in most cases of recrystallization and coarsening. Thus, it was found that, in general, the mobility is very low for boundaries between grains of nearly identical orientation, or for coherent twin boundaries. On the other hand, the boundaries between two grains of a relative orientation correspending to a [1111 rotation of 30" to 40" have the highest mobility in face-centered cubic metals. If a large variety of nucleus orientations are produced grow- by means of a highly inhomogeneous local deformation, nuclei close to the above orientation are found to grow fastest.z4 In view of this evidence and of the fact that the preferred orientation relationship is the same in recrystallization and in coarsening, the oriented growth theory appears by far the more promising one. Since the origin of nuclei in primary recrystallization is certainly different from that in coarsening, the occurrence of the same orientation relationship in the two processes would be difficult to explain on the basis of oriented nucleation. other advantages of the oriented growth theory are its capability of accounting for the often observed sharpening of the texture in coarsening, and its suitability for explaining the role in the formation of the ''cube texture,, of the most important variables, such as the degree of rolling, the penultimate grain size, and the time and temperature of the last anneal: No similarly consistent explanation of all these effects has ever been offered in terms of oriented nucleation. An important problem in connection with the oriented growth theory is the following: In the ce-c entered system there are four [111] axes and

Jan 1, 1952

By W. C. Shanks

Seventeen deeps, which contain hot or cold brines and/or metalliferous sediments, have been discovered in the axial rift zone of the Red Sea. Metalliferous activity results from the unique geological setting of this incipient ocean basin: oceanic crust intruding in a central rift zone flanked by thick evaporite sequences. Brine pools tend to occur in structural depressions where- transform faults intersect the spreading axis. The most significant metalliferous occurrence is in the Atlantis II Deep, which contains approximately 227 Mt (dry weight) of metalliferous sediment which averages 1.04% Zn and 0.28% Cu. Higher potentially economic grades (3-6% Zn, 1% Cu, 50 glt Ag) occur in the Southwest Basin of the Atlantis II Deep, comprising total metal tonnages of 1.7 Mt Zn, 0.4 Mt Cu, and 5000 t Ag. The Pre-Pilot Mining Test conducted in 1979 raised 15 000 m3 of mud by a slurry process and demonstrated the feasibility of mining, concentration by froth flotation, and tailings disposal at sea. A Pilot Mining Test is scheduled for 1983-1984. The metalliferous discoveries in the Red Sea provide a model example of deep marine mineral exploration. Detailed mapping of bottom bathymetry and brine-interface reflectors using a high-resolution narrow-beam echo sounder has been the most effective exploration tool in the Red Sea. Followup coring has discovered additional metalliferous deposits in basins without present-day brines, and potential exists for additional discoveries. Geochemical exploration using heavy metals values in sediments (iron, manganese, zinc, copper, and mercury) and sulfur isotope values of sulfides are considered to be the most promising techniques for discovery of currently inactive deposits. Positive sulfur isotope values in the range I to 17 are an indication of hydrothermal sulfides in the Red Sea, and there is considerable contrast from back- ground bacteriogenic sulfides ( - 10 to - 45).

Jan 1, 1983

By J. E. Strongman

This paper describes a system dynamics model of the international copper system. The development of the model is described regarding the questions it was designed to address, model boundary, major sectors and actors, the availability of data, the copper life cycle, and major supply and demand dynamics. A base forecast is presented describing future supply, demand, capacity, prices, trade flows, scrap flows and capital expenditures from 1976-1990 for the major producing and consuming market economy blocs.

Jan 1, 1977

By Jack A. Simon, M. E. Hopkins

GENERAL GEOLOGY Coal is defined as a combustible rock that originated in the accumulation and physical and chemical alteration of vegetation. Coal can be ignited and burned like the wood that was man's earliest fuel, but coal gives more heat than the same amount of wood and has many industrial uses. Unlike wood, coal is not generally found on the surface of the ground but is mined from the solid rock of the earth. Before taking up the occurrence, formation, and the unique character of coal in the rock sequence, let us briefly consider the general character of all rocks in the crust of the earth. Relatively little is known about the very earliest history of the earth, although a number of logical theories have been developed. Manned exploration of the moon and the rocks returned to earth continue to provide some answers to questions concerning the earth's origin and history. The period of earth history with which we concern ourselves here begins after great areas of water had evolved on earth and substantial land areas of once molten (igneous) rock existed. Weathering and other processes that attacked the surface of the rocks reduced them to small particles. Water provided by rainfall transported this material, ultimately, to large bodies of water where it was deposited. Thus was initiated the geologic sequence of sedimentary rocks that lie above the once molten igneous rocks. The crust and upper mantle of the earth are made up of several large plates along which differential movement (primarily horizontal) takes place. Such movements, although small, are occurring today. These horizontal movements are accompanied by vertical movements causing important changes in the relative position of the continents and oceans. Low-lying coastal swamps with favorable climates are ideal locations for coal accumulation and burial by river-borne sediments, and large areas

Jan 1, 1981

By L. C. Brown, A. J. Stewart

Phase transformations have been studied in Ag-Zn alloys quenched from the high-temperature bcc 0 phase and lying in the composition range 37.4 to 50.0 at. pct Zn. On quenching, the alloy with the lowest zinc content transformed to massive a (fcc); all other alloys formed the ordered (3' phase. On deformation, a martensitic reaction took place forming a close-packed structure. At Lou' zinc contents transformation to this structure was complete. However, above 43 at. pct Zn a p.rogressively increasing amount of ß' was retained following deformation. The close-packed structure was fcc at lower zinc contents (under 47 at. pct Zn) and either hcp or a mixture of fcc and hcp at high zinc concentrations. The structures produced by cold working were unstable and on aging transformed to the ß' phase or the complex hexagonal to phase. For low zinc contents (under 43 at. pct) the fcc st-ructure transformed directly to the equilibrium To phase. With higher zinc contents, some 13' was retained following defownation, and on aging the amount of this phase relative to the close-packed structure increased. On further aging both structures transformed cornpletely to PO. Metallographic examination indicated that the nature of the deformation product depended very markedly on the mode of deformation. Tensile deformation gave a microstructure characteristic of thermal martensite. KING and Massalski1 have shown that an alloy of Ag-50 at. pct Zn quenched from the high-temperature bcc ß phase undergoes a low-temperature ordering reaction forming ß' which can be retained to room temperature. On deformation an hcp phase is produced, although this is unstable and the structure reverts completely to ß' on aging. In the present paper, the work of King and Massalski is extended to cover a wide composition range in the p phase, observations being made of the structure of the quenched 13 and of the effects of deformation and aging. The relevant portion of the Ag-Zn phase diagram is shown in Fig. 1. King and Massalski have shown that close to stoichiometry the ß' phase is the equilibrium structure at low temperatures. The approximate composition range of this phase, taken from a recent paper by Pops and Massalski,3 is shown on the phase diagram. The locations of atom sites are very similar in the ß' and to structures, and the 4, structure can be derived from the 0' structure by a small movement of atoms mainly in the direction of the cube diagonal.4'5 However, the probability of filling any particular atom site by a silver or a zinc atom is markedly different in the two structures. The structure can be considered partly ordered but the arrangement of the ordered atoms is completely different from that in the p' structure and transformation from ß' to requires a large fraction of the atoms to change position. It has been shown that the ß' transformation is thermally activated involving normal nucleation and growth processes.5,8 Massalski and Barrett7 have shown that in the Cu-Zn binary the (3 phase can be retained in the ordered state to room temperature over a wide composition range. On deformation a new close-packed phase is produced, the structure varying from fcc to a mixture of fcc + hcp to hcp alone with increasing zinc concentration. It appears that an ordering reaction is necessary to retain the bcc phase to room temperature. In CU-Ga,8 the bcc phase cannot be retained to low temperatures as it transforms by a massive reaction above the ordering temperature of the ß phase. The structure of the massive phase is very similar to that in Cu-Zn, varying from fcc to fcc + hcp to hcp with increasing zinc concentration. Similar structures have also been observed in CU-A1,9 Ag-Cd,10,11 and Ag-Al.12 EXPERIMENTAL The alloys were prepared by melting fine silver (99.99 pct purity) and electrolytic zinc (99.999 pct

Jan 1, 1969

By H. V. Winchell

An examination of the Pachucal and El Oro districts in July, 1920, although cursory and incomplete, disclosed facts of more than passing interest to the student of ore deposits; and inasmuch as the literature on these districts is limited and some of their features are little understood, a brief account may prove valuable as reconnaissance observations to be amplified by more thorough and competent observers in the future. Where no complete monograph of important mining camps has been published a partial presentation of the data is often useful, as it sometimes leads to fuller and more accurate descriptions, by stimulating discussion. The following notes are presented with the consent of A. F. Main, managing director of the El Oro Mining and Railway Co., whose fund of information and wide acquaintance with both districts alone made it possible to cover so much ground in a short time. I have also to acknowledge gratefully the aid of C. A. Lantz and D. S. Calland of the Santa Gertrudis and Real del Monte companies, respectively, in connection with permission to inspect geological features of interest in their mines. Pachuca, Hidalgo, Mex. This mining camp has been described by Ezequiel Ordonez2 and by A. F. J. Bordeaux.3 Reported to have been discovered in 1522, it has produced silver valued at between $250,000,000 and $375,000,000. Subsequent to the discovery here, by B. de Medina, of the patio process. in 1557, its production was increased, and now, using cyanidation, the output of the camp is nearly one-sixth of the production of the world. Topography and Climate The Pachuca district consists of a series of mountains and valleys, the minor features of which extend in an easterly and westerly direction and reach elevations of 8000 to 10,000 ft. (2438 to 3048 m.) above the

Jan 1, 1922

By C. L. Sollenberger, Will Mitchell, Ford F. Miskell

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of' this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By Will Mitchell, Ford F. Miskell, C. L. Sollenberger

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of' this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By H. M. Chance

Recent research work has shown that coal can be produced, at reasonable cost, from almost all coal-mining districts containing not more than 3 to 8 per cent. of ash. From coal so produced, an abundant supply of coke, suitable for blast-furnace operation, can be made containing from 12 down to 6 per cent. or less of ash. These statements apply broadly to the Appalachian coal belt, including most of the mining districts in Pennsylvania, Ohio, West Virginia, Kentucky, Tennessee, and Alabama. The exceptions will generally be found among those coals carrying a prohibitive percentage of sulfur. Any gravimetric heavy fluid method of separation will effect a reduction in the percentage of sulfur, but this reduction may not be sufficient to produce, from coal unfit for metallurgic use, a product that can be so used. When a large part of the sulfur is in the form known as "organic sulfur, "or is present as very finely disseminated and homogeneously distributed pyrite, possibly it cannot be eliminated from the low-ash coal produced. When the sulfur exists as pyrite in distinct layers, bands, or nodules, or when it is finely disseminated but is irregularly distributed, often a low-ash coal low enough in sulfur to make good metallurgic coke can be produced from relatively impure coals. It has generally been assumed that the quality of coke on which blast furnaces must be operated depends on the geographic location of the furnace, and that the grade of coke on which a blast furnace must operate is that produced from the best coal obtainable by careful mining; or if the coal is prepared by washing, hand picking, or other means by which the foreign impurities are removed, that the grade of coke on which the furnace must operate depends on what has been termed the "inherent ash" of the particular coal. The term "inherent ash " is generally understood to mean the percentage of ash present after all removable (free) impurities, slate, fireclay, high-ash bony coal, and pyrite have been removed, and is usually applied to the percentage of ash present in run-of-mine coal from any mine after these impurities have been removed. Perfect washing, or perfect preparation, is understood to be attained when the percentage of ash in the washed coal is reduced to the percentage of inherent ash; that is, of ash that cannot be removed by the washing processes in common use. Wash-

Jan 1, 1924

By Bruce W. Gonser

TIN is not yet classed as a rare metal, but it has taken a long stride in that direction in the last ten months. It is now in Group 1 of the War Production Board's critical list, along with such company as magnesium aluminum, and nickel. This is in sharp contrast with the position a year ago when the supply well exceeded demand, and tin was used when feasible in place of really scarce metals. The geographical sources of tin production in recent years are shown in Table 1. Preponderance of former production in southeastern Asia, particularly Malaya and the Netherlands Indies (but all now controlled by the Japanese). is entirely too marked to be funny. Of the 1940 known world production of 237,000 long tons nearly all was controlled by the United States, Great Britain, and their friends. Now their supply is from countries that produced only 28 per cent of that amount. This excludes China and Australia, which because of shipping difficulties and local consumption, cannot be expected to export much tin. In spite of some expected increase in production, therefore, the supply is, and will continue to stay for at least several years, way below that desired for even normal uses. Although deliveries to consumers in the United States alone

Jan 1, 1942

By A. M. Riddle

GROWING out of the nation's most colorful era of railroad building, and with the vision of early pioneers who foresaw a great future for the Western Empire, the Colorado Fuel & Iron Corp. set as its objectives The establishment and building of colonies, towns, schools; industries such as coal mining, iron making and manufacturing works; canals and roads. This was the beginning of CF&I in the year 1872, and from this small western beginning has grown a company that has achieved national importance, ranking ninth in size in steel producing capacity, with over 22,000 employees and operating 14 plants in strategic locations throughout the United States.

Jan 11, 1953

By K. Kobayashi, K. Ueda, K. Yamaguchi

Lead concentrates from Kuroko (black ore) mines, which contain 4-7% Cu, 55% Pb, 3-777, Zn, and 0.5-0.9% As, are pretreated by a hydrometallurgical process before electric furnace smelting with other lead resources from Kuroko. The hydrometallurgical pretreatment involves sulfuric acid leaching in the first stage and ferric leaching in the second stage. This paper describes the short history of lead recovery from Kuroko and the performance of laboratory tests and pilot plant and commercial operations.

Jan 1, 1985

By J. D. Rice, H. H. Rachford, G. H. Bruce, D. W. Peaceman

The problem of unsteady-state gas flow through porous media leads to a second-order non-linear partial differential equation for which no analytical solution has been found. In this paper a stable numerical procedure is developed for solving the equation for production of gas at constant rate from linear and radial systems. An electronic digital computer is used to perform the numerical integration using an implicit form of an approximating difference equation. Solutions are presented in graphical form for various values of dimension-less parameters. The solutions are compared with the laboratory study of gas depletion in a linear system. INTRODUCTION Production of fluids from porous rock reservoirs is essentially a transient process. Transient gradients develop as soon as production begins, and further withdrawals continue to cause disturbances which propagate throughout the reservoir, each adding in some way to the prior ones. A correct mathematical analysis of this behavior is complicated by the fact that the transient or unsteady-state flow of compressible fluids must be described by difficult second-order partial differential equations. As a practical matter, three distinctly different cases arise: 1. Flow of single-phase liquid 2. Flow of gases 3. Multiphase flow The first of these has been found to give a linear second-order equation similar to the well-known heat flow equation. where 7 is fluid density, 8 is time, and a a constant for the system, provided d 7 = r cdp, where the compressibility, c, is constant over the range of pressure, p, considered. Solutions of Equation (1) for both linear and radial flow are available in several forms.2'3' On the other hand. the second case, which is the flow of gas, gives a non-linear second-order equation, the solution of which is not known. Although a number of approximate solutions have been proposed, each is limited in value by the associated simplifying assumptions. Inasmuch as the analysis of transient flow is limited to liquid systems, a solution of the second case is necessary if further progress is to be made in studying underground fluid movement. For this reason a solution of Equation (2) was undertaken by means of numerical integration of approximating difference equations. BASIC DIFFERENTIAL EQUATION Equation (2; is derived by combining the equation of continuity, the perfect gas law, and Darcy's law to give the basic differential equation Strictly speaking, the fluids present in a gas reservoir are not perfect gases. Furthermore, there are indications that over certain velocity ranges, Darcy's law is not applicable. It would not be practicable. however, to attempt to obtain numerical solutions which would take into account all the possible variations from these laws which could occur in actual systems. The

Jan 1, 1953

By C. R. Fast, George C. Howard

Laboratory and field testing of various squeeze cementing techniques and materials revealed that many improvements could be made in squeeze cementing operations. The use of a slow-pumping squeeze cementing procedure permitted the control of the quantity of cement displaced into a formation and aided in obtaining a high final squeeze pressure. Field testing indicated the desirability of obtaining high final squeeze pressures, the need for improved formation breakdown fluids, and the necessity of controlling the pressure differential during testing after a squeeze job. INTRODUCTION During the past few years, squeeze cementing operations have been investigated, both from the theoretical as well as the practical point of view, in an effort to arrive at some solution to the many and varied problems that arise with this type of operation. A review of well files indicated that in many instances, wells were being squeeze cemented four and five times before a satisfactory pressure buildup was obtained. There seemed to be considerable variation in opinion as to the proper method of squeeze cementing, as well as disagreement as to the proper breakdown agent, the quantity of cement that should be used, type retainer and length of WOC* time that was necessary. Consequently, it was deemed advisable to approach this problem theoretically, field testing each idea developed in hopes of eventually arriving at a squeeze cementing procedure that would give reasonable assurance of a successful job after one squeeze cementing operation. This investigation was. therefore, divided into two broad headings: (1) Preliminary studies, which include both theoretical and laboratory studies, and (2) Field investigations to determine the proper squeeze cementing methods. PRELIMINARY STUDIES Overburden Pressure Studies Squeeze cementing problems are so intimately related to the earth's overburden pressure that solutions to them are very difficult, if not impossible, without an understanding of the nature and magnitude of the overburden pressures encountered at the depths of producing wells. It was thus felt that the first approach to research on squeeze cementing should be made through a study of these pressures. Since there has been rather loose usage of a number of the terms related to overburden preasure by different writers, the terms to be subsequently used are defined here. Theoretical overburden pressure is the calculated pressure at any given depth exerted by the theoretical weight of overlying formations as calculated from the average rock density. Fluid displacement pressure is that pressure at which fluid can be injected into a formation after it has been broken down. It may be more or less than the theoretical overburden pressure. Formation breakdown pressure is that pressure at which a formation parts or breaks and is usually thought of as fluid displacement pressure plus rock strength. Breakdown agent is that fluid with which the formation is fractured. The first step in the study of the earth's overburden pressures involved a review of pertinent technical literature. The general opinion expressed was that the overburden pressure gradient of the earth's formations is roughly 1.0 psi per foot of depth, and that application of sufficient pressure to stratified formations. will cause them to part at or parallel to the bedding planes. The second step in the study of overburden pressures involved a study of available well data in an effort to obtain some definite information as to the actual values experienced in the field for the above mentioned terms. Data from 115 cement squeeze jobs in the Gulf Coast area and 46 cement squeeze jobs and acid jobs in the West Texas-New Mexico area were closely analyzed. The analysis of these data showed that the average formation breakdown

Jan 1, 1950

Some specific observations might be appropriate concerning the reporting of Research and Development results. Each report is usually directed towards a particular group, such as technical, operational financial, or marketing. The requirements and background of the group receiving the report must be considered, and the emphasis and coverage geared to the training of people concerned. For reports that might have large and varied distribution, it is often feasible to group, either as sections or appendixes, the special details and information of interest only to certain functions within the organization. (A check list prepared in conjunction with the various users of the report is sometimes useful to prevent omissions.) Typical points listed might be: Financial- (1) capital requirements, (2) timing of capital expenditures, (3) tax implications, including depreciation, depletion and investment credits, (4) changes in working capital.

Jan 10, 1967

By R. W. Raymond

This name is applied to the present mining law, as enacted in 1872 and since, to indicate its leading characteristic—in which it differs from all previous mining laws of this or any other country. The earlier act, passed in 1866, was practically the first attempt of Congress to deal with the question of mining titles upon the public domain. It was framed after nearly twenty years of acquiescence on the part of the Government in the self-constituted tribunals, officials, rules, and customs of the mining districts. In its recognition of these, and in several other particulars, the act of 1866 was open to serious criticisms. It is the purpose of this paper, not to trace the history of legislation on this subject, or show in detail what were the faults of the earlier law, but rather, by a discussion of certain aspects of the present law, to point out how great a revoluition it has effected in the rights of mining locators, and to indicate some of the difficulties attending its application. In the attempt to correct the vagueness of the act of 1866 an entirely new elernent was introduced into the law, bringing with it a new set of difficulties. Under the act of 1866 and the miners' customs which it followed, the lode was the thing claimed and subsequently acquired by patent. And the claim to a given number of feet on the longitudinal course of the lode was rooted in 'a discovery of any part of the lode in any part of the claim. ("Extensions" could in many districts—perhaps universally—be located and claimed on the strength of the discovery in the principal claim to which they referred; but this is a point not essential to the present discussion.) It was not necessary to find the outcrop or the upper edge of a lode in order to lay a valid location upon it. An explorer, sinking a shaft and intersecting a lode not already discovered and claimed by another, could claim by that discovery the number of feet along that lode which the local laws might permit (not exceeding the maximum set by the United States statute) whether his sur-

Jan 1, 1884

By A. F. Bertuzzi, M. R. Tek, F. H. Poettmann

A method is presented for predicting pressure drop for two-phase fluid flow in horizontal pipes. A set of 267 experimental measurements randomly sampled from approximately 1,000 measurements from various literature sources was used. Pressure gradients calculated by the procedure developed and compared with the experimental values showed a bias of +0.82 per cent and a standard deviation of 20.8 per cent. The advantatges of this method over other available methods of predicting two-phase flow pressure drop are (a) its comparative simplicity of application, (b) its relative independence of flow patterns, (c) its accuracy, which on the basis of a statistical evaluation predicts pressure drop closer than other available methods, and, (d) its ability to satisfactorily correlate laboratory data from various sources while the correlations from these sources do not appear to agree with one another. The method has been reduced to a simplified graphical procedure, suitable for field use. A two-phase f factor is defined and correlated with parameters involving the flowing gas-liquid mass ratio, a Reynolds number for the gas phase, and a Reynolds number for the liquid phase. The choice of parameters allows the correlation to reduce to the usual f factor plot for the limiting conditions of (111 gas or all liquid. INTRODUCTION The mechanics and characteristics of two-phase flow systems have been of interest throughout the industry for some time. In numerous engineering installations such as pipe lines, chemical reactors, and heat exchangers, two-phase flow conditions are of every day occurrence. In oil production operations it has been desirable, in some cases, to consider transporting gas and oil together in a common pipe from oil field to process plant. The trend toward centrally located stock tank batteries in oil fields has resulted in longer gathering pipelines in which more than one fluid phase is flowing. The increase in the producing capacity of oil wells due to new production tech- niques has created the need for review and re-design of many surface gathering lines for properly handling the increased production. Optimum pipe size for the situations described above has become an important factor. The problem which is of interest here involves the ability to predict the relationship between pressure drop, fluid properties, fluid rates, pipe diameter, and pipe length. Although the literature1,5,10,13,18,19 contains various articles dealing with specific cases of the problem, Lock-hart and Martinelli17 proposed the most general solution. Their method has been later modified by Baker:1 Alves2 demonstrated that different flow patterns are possible for a flow mechanism defined by Martinelli such as gas turbulent, liquid turbulent. Baker explained deviations experienced with Martinelli's correlations on the basis that different flow patterns could exist for the same flow mechanism. Using Martinelli's method of correlatioil, Baker correlated data for each flow pattern for the turbulent-turbulent flow mechanism. Bergelin and Gazley6,7 presented a correlation for predicting gas phase

Jan 1, 1957

By M. M. Austin

Pure metallic tantalum, from a practical standpoint, is one of the newer developments in the metal field. Although it was used as filament in incandescent lamps in 1906, only within the last, five years has the metal been available in sufficient quantity and suitable form for more general application. In addition to corrosion-resisting properties and high melting point, the metal has an ability to withstand unusual amounts of cold working. It affords some striking demonstrations of block movement during plastic flow. Strength and Ductility of Tantalum Since there is no good way of defining working properties numerically, illustrations will be used. It is possible to roll a bar of pure tantalum 0.4 in. thick to sheet 0.001 in. thick, without heating or annealing. The sheet produced will be sound and may be bent upon itself at right angles to the direction of rolling. Longitudinally the sheet will be somewhat brittle. A disk of annealed metal may be cupped and drawn to the form of a capsule 3/16 in. dia. by 146 1? in. long. If carefully handled this capsule can be further deformed by drawing to a tube having an outside diameter of 0.050 in. Disks of tantalum may be spun into tubes of 39 in. dia. and 1½ in. long. In the form of rod, reductions may be made from 0.4 in. to 0.001 dia. In the latter process, it is necessary to heat the wire four or five times to 500" C., at intervals between 0.040 and 0.001 in. Although the melting point of tantalum is 2850" C., these heatings at 500" C. are sufficient to distinctly anneal it. Published figures on the strength and ductility of tantalum are not particularly accurate. This is due to the fact that these properties vary widely, depending on the extent to which the metal is contaminated by gas. There are no sharp critical points in these changes with gas content; samples of metal will vary from a springy or actually brittle condition to one of leadlike softness. Samples that have had a prolonged heating at high temperatures in a good vacuum, under conditions such as would be provided in vacuum-tube experimentation, will yield a product of about the hardness of annealed copper. The usual commercial metal will have the hardness of annealed mild steel.

Jan 1, 1930

By Charles Mitke

EXCLUDING top-slicing, and sublevel caving, large production caving methods may be divided into two general classes, the branch raise, or undercut caving method, and the combined shrinkage and caving method, each of which has a number of variations, the result of continual efforts towards obtaining lower costs and better extraction, by the introduction and substitution of minor improvements and modifications. EARLY CAVING METHODS Present caving methods are the cumulative result of developments covering a period of many years, with the most rapid growth during the past 15 years. They originated, presumably, from early English stoping methods, and, as far as is generally known, were first introduced in the Michigan iron district. They have had their greatest expansion and application in the large low-grade porphyry coppers. In their present form, they are probably a development and combination of sublevel caving and shrinkage (back-stoping on ore) with gravity handling of broken material. Sublevel caving, as practiced in the Michigan district today, is a combination of drift, or crosscut, mining, with top-slicing, and caving, supplemented by later refinements in the shape of mechanized handling of broken ore. A height of anywhere from 16 to 20 ft. is generally taken, and the ore is drilled and blasted along the drift or crosscut for half this height (say 8 to 10 ft.), after which the upper 8 to 10 ft. caves and breaks of its own weight, with comparatively little assistance from drilling. This

Jan 1, 1928