Search Documents

By Heihachi Kamura

In this research, the proper temperature for the reduction of iron ores by carbon monoxide was determined. Also, the difference of the rate of reduction on the sizes of ore under four mesh per linear inch was estimated, but no evidence could be found. Rates of reduction on the seven kinds of ore were compared with the results of the experiment, showing a close relation between reducibility and density of ore. Finally, the maximum size of ore that can be reduced in applicable length of time was determined. The author thinks that the process of production of steel may be replaced by low-temperature reduction of iron ores some time in the future. THE reduction of iron oxide, such as Fe203, to iron in the blast furnace is performed principally by carbon monoxide, but partly by solid carbon by the two following reactions: Fe203 + 3CO = 2Fe + 3CO2 2Fe203 + 3C = 4Fe + 3CO2 It is known that reduction by carbon monoxide takes place at a much lower temperature than reduction by carbon and that the reducing action of carbon monoxide progresses to the inside of the ore in lump form by gaseous diffusion. In the reduction by carbon, however, the reducing action takes place only at the contact surface of the ore and carbon, so that the more complete the reduction by carbon monoxide, the more efficient is the operation. However, the reduction does not progress as shown in the foregoing formula, because carbon dioxide acts oxidizingly on the metallic iron to such a degree that when the gaseous composition reaches a certain proportion of carbon dioxide to carbon monoxide, the reduction practically stops, even though the gases are moving slowly through the heated ore. The proportions of carbon monoxide and carbon dioxide in the gas depend on the kind of iron oxide and the temperature of reduction, also the duration of time in the reaction. The longer the time of the reaction, the higher the proportion of carbon dioxide obtained in the gas, but finally it will attain to a condition of equilibrium.

Jan 1, 1925

By F. P. Bullen

Empirical relationships between fracture stress, orientation angle, and diameter of crystal have been determined at 77°K. Orientation ranges of markedly different behavior were found—a law of constant normal stress&apos; of value a (diameter)-1/2 for the fracture of ductile crystals, and a condition of shear stress (or strain) for more brittle crystals. The observations are not consistent with current theories. An interpretation is advanced which is also applicable to observations on the effect of prestrain at room temperature on the subsequent fracture stress at 77°K and to the effect of cyclic stressing on the cleavage strength.&apos;&apos; The law of constunt normal stress&apos; and the brittle ductile transition are also explained. The interpretation is more consistent with the initiation of cracks by intersecting dislocations than with theories based on stress -concentration by dislocation arrays. ZINC single crystals are particularly suited to the study of cleavage because fracture occurs on the basal plane over a wide range of crystal orientations. Analysis of the conditions of stress and strain at fracture in crystals of different orientations should indicate which parameters control the cleavage process. Unfortunately, controversy has arisen over the correct empirical relationship between tensile fracture stress and orientation. Schmid&apos;s observations1,2 favored a &apos;law of constant normal stress&apos;, as observed in other materials.2 For zinc, however, the observed values are far below the theoretical strength and cannot represent the true limit of cohesion between neighboring atomic planes. Hence, the interpretation of such a &apos;law&apos; is not straightforward. Deruyttere and Greenough3,4 found a complex variation between tensile fracture stress and orientation; this variation did not agree with a &apos;law of constant normal stress&apos;. Two theories have been advanced to account for their observations: a) the propagation of cracks from low-angle boundaries,5 and b) the release of energy from piled-up dislocations during crack-propagation.4 The present work resolves the apparent discrepancy between the observations and shows that neither of the above theories are applicable to the tensile fracture of zinc single crystals. A phenomenological explanation, along the lines suggested by Gilman,&apos; is advanced and successfully applied to previously unexplained effects. EXPERIMENTAL DETAILS &apos;Crown Special&apos; redistilled zinc was used, except for one comparison series op tests using &apos;Tadanac&apos; electrolytic zinc. Crystals of 1 mm diam, subsequently called &apos;1 mm crystals&apos;, were grown from the melt in vacuo in precision-bore Pyrex tubes internally coated with graphite. Several specimens 1 in. long were cut from each crystal and chemically polished. Jigs were used to minimize handling strains, and crystals were mounted in the Polanyi machine the day prior to testing to allow recovery from any such strains. One-mm crystals were chemically polished for long periods to obtain 0.1 mm (approx) crystals. One-mm crystals were cemented into miniature gimbals by &apos;Araldite&apos; casting resin. The Appendix gives the reasons for using gimbals and the results obtained by other methods. More complete details of all techniques are given elsewhere.7 The symbols and terminology used are as follows: X = orientation angle (angle between tensile axis and line of greatest slope in the basal plane). T = tensile stress (on true cross-section) S,N = shear and normal stress (components of T with respect to the basal plane) ? = shear strain D = crystal diameter. The subscript &apos;f&apos; will be used to denote values at fracture. PART I-ANNEALED CRYSTALS EXPERIMENTAL OBSERVATIONS One-mm crystals were used to establish the variation of fracture stress at 77°K with orientation at fracture (Xf), Fig. 1. For 18 deg = Xf = 55 deg, a &apos;law of constant normal stress&apos; was observed. For Xf > 55 deg, the fracture condition approximated to a constant shear stress. At Xf< 18 deg, twinning occurred before fracture so that the results were not typical of homogeneous single crystals,4,8— such specimens will not be considered herein. The dependences of fracture stress upon Xf were of similar type for 6 mm,* 1 mm, and 0.1 mm crystals,

Jan 1, 1963

By M. M. Fine

Normally the U. S. produces less than 10 pct of its annual manganese requirement. About 95 pct of domestic consumption is used by the steel industry.&apos; The strategic and critical nature of manganese has been recognized by its inclusion in the national stockpile and by intensified research directed toward cataloging and evaluating domestic manganiferous deposits. The USBM has participated in these activities for many years with field and laboratory studies to assess the extent and potential utilization of domestic manganese ores. One area of particular interest is in the vinicity of Batesville, Ark., where deposits have been mined since 1849 for both manganese and ferruginous manganese ores. Production is centered in Independence County, but deposits are also found in Sharp, Izard, and Stone counties in north-central Arkansas. Miser has described the geology and manganese mineralization in some detail.&apos;. * "he rocks of the area are sedimentary, consisting of sandstone, limestone, shale, and chert. The two formations of greatest importance,&apos; Fernvale limestone and Cason shale, are host rocks of the primary manganese mineralization. Through 1955 the district produced some 230,000 long tons of manganese ore (35 pct Mn or more) and 236,000 tons of ferruginous manganese (10 to 35 pct Mn).5 Most of the ore has been mined from deposits of manganese oxides in residual clays resulting from weathering of the two formations noted above. Concentration methods have been primitive, consisting for the most part of washing. hand picking, and jigging. A significant accomplishment in the district in recent years was the USBM recognition and investigation of the huge manganese potential represented by unaltered Fernvale limestone. systematic reconnaissance of manganiferous limestone and other occurrences has been in progress since 1953 to delineate the extent and tonnage of manganiferous materials. Results of that survey have appeared in two recent publications,1-5 which ascribe to the district an inferred reserve of 166 million long dry tons at a grade of 5 to 6 pct Mn. Most of this was mancaniferous limestone with an estimated content of 5 pct Mn. Specifications: Beneficiation was carried out on a group of manganiferous limestones to develop a way to recover commercial-grade concentrate from this extensive resource. The following chemical specifications were established by the GSA for metallurgical manganese ore acceptable for delivery to the national stockpile: Size specifications were not considered, as it was assumed that the concentrates could be pelletized or sintered. Manganiferous Limestones: Of the 11 samples tested to date, six were taken by cutting vertical channels across beds of limestone outcrops. Diamond drilling through overlying barren chert into unex-posed limestone provided four samples, and the last was a churn drill sample. In general, the samples were dlrk, fossiliferous limestone containing small amounts of braunite, hausmannite, rhodochrosite, massive and micaceous iron and manganese silicates, quartz, barite, and glauconite. The braunite and other manganese oxides partly to completely replaced some of the calcite and fossil material. The calcite was generously stained with mangenese and iron oxides. Phosphorus was present in all samples as collophanite grains, calcium phosphate fossil replacements. or an unidentified manganese-bearing carbonate. The difficulty in separating this complex array of minerals was further complicated by a very intimate association. Although some manganese grains as large as Ik in. were noted, grinding to subsieve sizes would have been necessary to liberate the components. Figs. 1 and 2 are micrographs, at X100, of typical polished sections in which white areas are manganese. gray is gangue, and black areas are surface depressions. By comparison with the 100 mesh opening, it is seen that some of the grains are coarse enough to respond, perhaps to tabling or flotation, but many are obviously beyond the scope of ohysical processing. Partial chemical analyses of the eight samples that were ultimately amenable to concentration are presented in Table 1. BENEFlClATlON RESEARCH Tabling: To take advantage of the presence of sand-size grains, both jigging and tabling were considered at the outset. Jigging was largely ineffective, but tabling achieved a partial recovery from most samples. As an example, the surface material from Baxter Hill was crushed to —28 mesh, hydraulically classified, and the coarsest spigot fraction was tabled to yield a concentrate, middling. and tailing. The latter two were reground to pass 48 mesh, combined with the primary fines, re-classified, and retabled. The middling and tailing were again ground, this time to pass 150 mesh, and deslimed at 20µ in a 3-in. hydraulic cyclone. The cyclone underflow was returned to the table to reclaim a small amount of high-grade manganese. An interesting facet of the gravity concentration developed on certain samples in which braunite was the principal manganese constituent. Since braunite has a Mohs hardness of 6 to 6.5, while the host rock, limestone. is only 3, a differential size reduction took place during crushing, and the

Jan 1, 1960

By O. Mellgren, A. M. Gaudin, P. L. De Bruyn

The adsorption density of ethyl xanthate on pyrite was determined as a function of xanthate concentration. Surface preparation of the mineral appears to have asafunctionsome effect on the subsequent adsorption process, A monolayer of xanthate on the surface is exceeded only in presence of oxygen. The effect of OH- , HS- (and x and CN- S=)and on the amount of xanthate adsorbed was investigated. Competition between OH- and X- (xanthate) ions for specific adsorption sites is indicated over a wide pH range. IN the flotation of sulfide ores, xanthates are most commonly used to prepare the surface of the mineral to be floated so that attachment to air takes place. The quantity of agent required to make the mineral hydrophobic is usually very small, of the order of 0.1 to 0.25 lb per ton of mineral. Details of the mechanism of pyrite collection are for the most part unsettled. Adsorption of collector has long been believed to involve an ion exchange mechanism as demonstrated for galena&apos; and for chalcocite.2 In the work on chal-cocite it was also demonstrated that a film of xanthate radicals unleachable in solvents that dissolve alkali xanthates, copper xanthate, or dixanthogen was formed at the surface of the mineral. The unleachable product increased with increasing addition of xanthate up to a maximum corresponding to an oriented monolayer of xanthate radicals. Pyrite is extremely floatable with xanthate if its surface is fresh.9 ut the floatability decreases rapidly as oxide coatings increase in abundance. Pyrite shows zero contact angle when in contact with ethyl xanthate solution at pH higher than about 10.5;4 at neutrality, a contact angle of 60" is obtained at a reagent concentration of 25 mg per liter. Alkali sulfides and cyanides are pyrite depressants. In this study of pyrite collection the writers have sought to relate measured xanthate adsorption to the method used in preparing pyrite, to the presence or absence of oxygen, to concentration of hydroxyl, hydrosulfide, sulfide, and cyanide ions. The principal experimental tool has been radioanalysis," " using xanthatcx marked with sulfur 35. Experimental Materials Pyrite: Unlike most sulfides, pyrite is a poly-sulfide. The structure given by Bragg7 resembles that of sodium chloride, the iron atoms corresponding to the position of sodium and pairs of sulfur atoms corresponding to the position of chlorine. The edge of the unit cell in pyrite is 5.40 A and in halite 5.63 A. The S-S distance in pyrite is 2.10 A; the Fe-S distance, 3.50 A: and the Fe-Fe distance, 3.82 A. Natural pyrite from Park City, Utah, was used in this investigation. Pyrite 1 was obtained by hand picking pure crystals. Pyrite 2 and Pyrite 3 were obtained from finer textured crystalline material containing inclusions of silicates. The same cleaning technique was utilized for the preparation of Pyrite 2 and Pyrite 3, whereas a different cleaning technique was used for Pyrite 1. Pyrite 1 was prepared as follows: The crystals were ground in a porcelain ball mill and the 200/400 mesh fraction was separated by wet screening with distilled water, followed by washing for 1 hr with deoxygenated distilled water acidified with sulfuric acid to pH 1.5. The acid was removed by rinsing with deoxygenated distilled water on a filter until a pH of 6.0 was reached in the effluent. This filtration was carried out under nitrogen. The sample was then dried in a desiccator under nitrogen. The period of time for which this pyrite sample was in contact with water containing oxygen was about 4 hr. The specific surface as determined by the BET gas adsorption method was 582 cm2 per g. Final material assayed 53.12 pct sulfur and 46.5 pct iron (theoretical, for FeS,: S, 53.45 pct; Fe, 46.55 pct). After crushing, Pyrite 2 and Pyrite 3 were washed with 1 M HCl. rinsed, and fed to a laboratory shakinq table to remove the small amount of silicates. The concentrate obtained was ground in a laboratory steel ball mill. The 200/400 mesh fraction was separated by classification in a Richards hindered settling tube. This fraction was then given a final wash with 0.1 M HCl and deoxygenated water was filtered through the sample. The final effluent showed a conductivity equivalent to that of a solution having a salt concentration of 0.3 ppm. Aqueous hydrogen sulfide solution was then added to the sampln (about 100 ml saturated H,S solution to about 1000 g pyrite under a few hundred milliliters of water) which was stored wet under nitrogen. The sample stored in this manner showed no indication of formation of iron oxides, whereas iron oxides appeared

Jan 1, 1957

By E. R. Parker, E. A. Smith

Metallurgists and engineers have always been interested in the mechanism of high-speed deformation because metals are rapidly deformed in various applica-tions and manufacturing processes. The deformation of metals by impact loads has recently engaged the attention of a number of investigators. Many of their results have not been disclosed but some of the published investigations1-8 have shown that the tensile strength, yield strength and elongation generally increase with increasing strain rate. The investigation reported herein is an attempt to determine the reason for this increase in strength and elongation. found to depend upon the strain rate. In the bars broken at high speeds, the slip bands appear to be more numerous. This might account for the higher strength as well as the greater elongation. Experimental Procedure Single crystals of copper (approximately 99.98 per cent) were made in graphite molds by the conventional method of lowering the mold out of the hot zone of a hydrogen furnace at a rate of one inch per hour. Solidification progressed from the bottom upward, forming a single crystal. The crystals were about 0.30 in. in diameter and 4 in. long. They were

Jan 1, 1944

By E. A. Smith, E. R. Parker

Metallurgists and engineers have always been interested in the mechanism of high-speed deformation because metals are rapidly deformed in various applica-tions and manufacturing processes. The deformation of metals by impact loads has recently engaged the attention of a number of investigators. Many of their results have not been disclosed but some of the published investigations1-8 have shown that the tensile strength, yield strength and elongation generally increase with increasing strain rate. The investigation reported herein is an attempt to determine the reason for this increase in strength and elongation. found to depend upon the strain rate. In the bars broken at high speeds, the slip bands appear to be more numerous. This might account for the higher strength as well as the greater elongation. Experimental Procedure Single crystals of copper (approximately 99.98 per cent) were made in graphite molds by the conventional method of lowering the mold out of the hot zone of a hydrogen furnace at a rate of one inch per hour. Solidification progressed from the bottom upward, forming a single crystal. The crystals were about 0.30 in. in diameter and 4 in. long. They were

Jan 1, 1944

By C. L. Ray, R. E. Baarson, H. B. Treweek

As an example of nonmetallic mineral flotation, the separation of several pegmatite minerals will be discussed in considerable detail, from both the laboratory-testing and plant-operation standpoints. The pegmatites have been chosen to illustrate the practicality of the selective separations of the minerals in a complex nonmetallic ore and, in so doing, to set forth a summation of the flotation art and technology which is applicable in part to the beneficiation of several less complex nonmetallic ores. In addition, a brief summary of descriptions of other nonnietallic mineral flowsheets and separations is included. Some of the industrial minerals now being concentrated by froth flotation methods commercially, or in the laboratory, are listed in Table 1. GENERAL CONSIDERATIONS There are two classes of chemicals that are normally utilized as collectors in froth flotation separations of nonmetallic minerals. These are defined as anionic and cationic and are typified by the fatty acids and amines, respectively. The fatty acids are selective to those minerals that have a high concentration of positive surface charges, such as the various calcium minerals typified by calcite, phosphate rock, and fluorspar. The amines are selective to those minerals with a high concentration of negative surface charges, such as silica sand and silicates. It should be noted, however, that by using various inorganic chemicals, a new or synthetic surface can be placed on specific minerals which produces different characteristics, thereby reversing the flotation reagent required for separation. The polar end of the collector attaches to the mineral surface either by chemical or physical adsorption; the nonpolar unreactive end is oriented away from the mineral surface. The result is a hydrophobic coating at the mineral surface which causes attachment to air bubbles. It is this surface condition that permits the floating of minerals which normally sink in water. In order to utilize these fatty acids and amine derivatives, several conditions .must be fulfilled. Before there can be a selective flotation process,

Jan 1, 1962

Long range expansion plans begun in 1966 by The International Nickel Co. of Canada, producer of over 50% of the free world supply of the white metal, are so mammoth as to give rise to the speculation that something might have to burst at the seams. From an annual level of capital expenditure of $35 to $70 million, the company jumped in 1967 to $145 million in new capital investment and will come close to $200 million in 1968. Inco expects to spend $700 million in the next five years, beginning in 1968, for new mines and surface facilities in Canada. The program involves the opening of nine new mines within the next 3 1/2 years, expansion of producing mines, and construction of new plants and modernization and expansion of established ones to process the increased ore production. Beyond this, the company is committed deeply in developing new sources of nickel abroad. Any one of these new projects, if proven economic, would necessitate expenditures of about $100 million or more. For Inco, the economic strain was relieved without a rupture this spring when Henry S. Wingate, company chairman, reported&apos; at the stockholders annual meeting that $150 million had been raised by the sale of bonds. This marked the first time in 32 years that the company had gone into debt.

Jan 10, 1968

By S. V. Krusiewski, J. W. Gabelman

Regional metallogenic zones and areas of equal paragenetic range have been interpreted from a compiled metallogenic map. of Mexico. Mineralization gradients of the pattern subsequently identified extend inland from coastal zones of high-temperature mineralization, and join in a central longitudinal zone of relatively low-temperature mineralization, apparently leaving no zonal room for lowest temperature deposits. The striking regional zoning pattern can be correlated with regional deformation gradients of similar position and orientation. The gradients represent at least three major orogenic cycles in two structural belts. Paleozoic structural belts existed along each coast with deformation gradients diminishing inland toward a narrow, central peninsular craton. The Mesozoic-Tertiary Mexican (Cordilleran) belt covered the entire country with a gradient oriented toward the Gulf of Mexico. Most ore deposits in this belt are of Tertiary age, although Tertiary mineralization gradients seem to have "inherited" the pattern left by Paleozoic tectonic gradients. Mineralization gradients can be used to identify the regions most favorable for the occurrence of selected metals. A metallogenic province is characterized by particular proportions of various metals, and the relative proportions can vary from province to province; but within any province the same intensity of mineralization would produce similar deposits in different places. Declining intensity of minetalization produces different kinds and sizes of deposits in zones that are concentrically arranged around sites of strongest rock alteration. On a regional basis, districts of similar average intensity of mineralization occur in zones that generally parallel some tectonic grain with the result that tectonic deformation has been designated a principal cause of mineralization. Variations in the type and intensity of deformation would determine the type as well as size of metal deposits. Mexico is especially favorable for such a study be- cause of its great abundance and variety of epi-genetic mineral deposits in various lithologic, structural and tectonic environments. The concept is also useful in recognizing portions of Mexico favorable for the occurrence of specific metals. METALLOTECTONIC ZONING IN MEXICO Theory: In studies of individual districts and groups of districts throughout North and South America, areal zoning of metal deposits generally seemed to respond to the paragenetic sequence of iron, gold, copper, zinc, lead, silver, antimony and arsenic, gold and fluorite. However, the definition of district zones is greatly obscured by contemporaneous or rhythmic deposition of metals, especially in the middle of the paragenetic range, and by the common superimposi-tions of different generations of metals. Zones could usually be distinguished only for groups of metals, such as early precious metals, base-metal sulfides, sulfosalts and late precious metals. The best defined zoning in a district is normally the spatial separation of the greatest volumes of altered and metallized rocks.&apos; Exceptions are districts representing the high- and low-temperature extremes of the mineralization range where the former creates a matrix for the latter. In most districts the total quantity of alteration products is greatly in excess of, and appears to be roughly proportional to, the total quantity of metallization products. Subsequent to the bicomponent nature of each district, the most important mineralogical feature is the great excess of one to several metals or minerals which results in a district identifiable as one of predominantly gold, copper, lead-zinc, fluorite, etc., although a great variety of other elements may be present. The para-genetic range for the abundant elements in any district is only a portion of the entire possible range for all the elements representing the complete process throughout the region. Early during investigations of this type, it became apparent that the consistent bicomponent character of districts allows two methods for studying epi-genetic mineralization patterns. One is to identify and plot altered rock "pipes,"* which are easily recognizable in the landscape by their anomalous

Jan 1, 1969

By Herbert H. Kouns, Harlan W. Nelson, Bruce O. Buckland

GASIFICATION of coal under pressure produces a gas that may be used as the fuel in a gas turbine. The pressure produced by a gas-turbine compressor (5 to 9 atm) should allow the use of high firing rates without unreasonably high solid carry-over rates. Hot make-gas with the tars contained in it in the vapor form can be used in a gas turbine. Most of the ash can be removed through a grate, and only a small portion of the ash and any of the solid combustible material carried over by the make-gas requires separation. The gas stream from which separation is required is a small portion of the total flow of a gas-turbine plant and hence the separator size will be small. The gas stream is reducing and will not, therefore, allow separator fires to occur. The response of the producer to rapid load changes is satisfactory. Only the air rate must change substantially in synchronism with the load. The coal feed, the steam addition to the blast, and the ash-removal rate can follow the load changes with time lags in the order of minutes. The necessary control equipment is simplified by these producer characteristics. With these possibilities in mind, the Steam Turbine Division of the General Electric Co. made arrangements with Battelle Memorial Institute in January 1945 to investigate the problems of the gasification process. A number of tests were made during this investigation on an updraft producer with a grate area of 1 sq ft. The equipment used has been described and the results of the tests made between 1946 and 1950 have been reported.1 The testing with this small producer was recently completed. The concluding tests were run to determine the effectiveness of a clinker-grinding grate and the effect of the operating conditions on the amount and character of the solid carry-over. The present paper describes the producer as modified, and gives the results of the tests using three coals. Another method of using coal in gas turbines is to pulverize it and burn it directly in the combustion chambers. This plan is being tried by the Loco- motive Development Committee of the Bituminous Coal Research, Inc., whose investigation has reached the stage of tests of full-sized equipment.

Jan 1, 1953

By James R. Cudworth, Joseph C. Mead

The Birmingham district of Alabama has utilized the slag from its blast furnaces consistently since the earliest development of the slag industry. Today there are producers of slag cement who started business in 1900, and who have, under a progressive policy, expanded the number of their products to meet present demands. There are producers of slag aggregates and other crushed slag products who have been successful for periods of over thirty years. There are at the present two companies, Cheney Lime and Cement Co. and the Southern Cement Co., manufacturing puzzolan cement; two companies, Birmingham Slag Co. and Woodstock Slag Co., making slag aggregates and by-products; one company, Tennessee Coal, Iron and Railway Co., a subsidiary of the U. S. Steel Corporation, producing ground open-hearth basic slag for soil conditioning. Two companies, the Sloss Sheffield Steel and Iron Co. and the Woodstock Slag Co., make slag concrete in ready-mix plants and one company, the Superock Company, manufactures fine and coarse slag aggregates under a new granulation process. NO Portland cement is made with slag as an ingredient, because dolomite is used so extensively as a blast-furnace flux that the magnesium content of the slag is excessive. Sources of Slag In the Birmingham district there are 22 blast furnaces, of which the majority are in blast. The present production is 165,000 tons of pig iron monthly; the production in 1935 was 1,297,960 gross tons1. There arc also two blast furnaces at Gadsden and one ferroalloy electric furnaee at Anniston. From these two sources is obtained slag to approximately 1.1 tons per ton of pig iron. History of Development of the Industry The history of the local utilization of slag as an industry probably starts with the Birmingharii Slag Cement Co. This company was

Jan 1, 1938

By Joseph C. Mead, James R. Cudworth

The Birmingham district of Alabama has utilized the slag from its blast furnaces consistently since the earliest development of the slag industry. Today there are producers of slag cement who started business in 1900, and who have, under a progressive policy, expanded the number of their products to meet present demands. There are producers of slag aggregates and other crushed slag products who have been successful for periods of over thirty years. There are at the present two companies, Cheney Lime and Cement Co. and the Southern Cement Co., manufacturing puzzolan cement; two companies, Birmingham Slag Co. and Woodstock Slag Co., making slag aggregates and by-products; one company, Tennessee Coal, Iron and Railway Co., a subsidiary of the U. S. Steel Corporation, producing ground open-hearth basic slag for soil conditioning. Two companies, the Sloss Sheffield Steel and Iron Co. and the Woodstock Slag Co., make slag concrete in ready-mix plants and one company, the Superock Company, manufactures fine and coarse slag aggregates under a new granulation process. NO Portland cement is made with slag as an ingredient, because dolomite is used so extensively as a blast-furnace flux that the magnesium content of the slag is excessive. Sources of Slag In the Birmingham district there are 22 blast furnaces, of which the majority are in blast. The present production is 165,000 tons of pig iron monthly; the production in 1935 was 1,297,960 gross tons1. There arc also two blast furnaces at Gadsden and one ferroalloy electric furnaee at Anniston. From these two sources is obtained slag to approximately 1.1 tons per ton of pig iron. History of Development of the Industry The history of the local utilization of slag as an industry probably starts with the Birmingharii Slag Cement Co. This company was

Jan 1, 1938

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always-have the same properties. The properties considered here, of course, are those inherent in the ingot immediately after solidification and not qualities imparted by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. Other variations in properties are due to variations in those constituents of steel (elements or compounds) that are not ordinarily included among the elements specified, thus not a part of the specified "composition." The term "constitution" is used to include not only the specified composition but also the nature and distribution of every element or compound contained in the steel entering the ingot mold; also included are items such as aluminum oxides and nitrides, presence of soluble gases, and dispersion of nonmetallic particles. When it is considered that the constitution of steel is determined by the addition or absorption into the bath of all such constituents from whatever source, it follows that constitution is of necessity the final result of steelmaking practice. It is the agency through which steelmaking practice operates to control the properties of the steel. The term steelmaking practice is here used in the broad sense, meaning the control of all the materials entering the steel and of the conditions under which the process is carried out. Steelmaking practice, thus defined, establishes the chemical system within which the reactions between components must proceed in obedience to the laws of chemistry. Thus the chemical constitution of the steel is established and, through constitution, the properties of the metal are established. In the preceding chapters it has been shown how the constitu-

Jan 1, 1951

By J. O. Brittain, E. Lautenschlager

Yield point measurements were made on polycrys-talline specimens of a iron deformed various amounts at 770, 1950, or 273°K, aged, and redeformed at 77: 195°, or 273°K. When the prestrain temperature is lower than that subsequent to aging, the yield point return is suppressed relative to specimens deformed at the same temperature both before and after aging. The degree of suppression is a function of both the magnitude of prestrain at the lower temperature and the difference between the deformation temperatures before and after aging. It is proposed that the suppression is caused by the formation of dislocation barriers during the initial low-temperature deformation. The aging kinetics of polycrystalline a-iron wires deformed at 77o or 303oK were studied at 44 " and 64 "C using internal friction measurements. No change was noted as a result of the difference in prestrain temperature. IN an earlier investigation1 it was observed that the return of the yield point was suppressed when a poly-crystalline specimen of a iron was plastically deformed at 77oK, aged at room temperature, and subsequently tested at room temperature. In order to investigate this observation, a research program was undertaken to measure the effect of prestrain temperature on the strain aging of a iron.&apos; According to Thomas and Leak,3 return of the yield point and internal friction are similar measures of strain aging since both are dependent on solute atoms leaving the solid solution. The decrease in internal friction as a function of aging time is indicative of the removal of solute atoms from the solution, while the return of the yield point as a function of aging time gives the rate of arrival of solute atoms at the dislocations. According to Cottrell and Bilby,4 the solute atoms create an "atmosphere" which locks the dislocations and causes a return of the yield point upon restraining. In this experiment, both methods of measuring strain aging were employed in order to have two independent measurements of the strain aging phenomenon. In a previous study,5 the strain aging kinetics of a similar lot of a iron were measured for specimens which were prestrained and tested at the same temperature over the range of 77" to 273°K. Although some differences were found in the correlation of the two methods employed for measuring strain aging, the kinetics of strain aging were unaffected by the change of prestrain and test temperature. In another study,6 dislocation line tension and the density of the solute atmosphere were found to contribute to the return of the yield point when ingot iron specimens were prestrained at 303°K and tested at a lower temperature, namely 77°K. This paper is concerned with changes in strain aging kinetics produced by pre-straining at 77" to 303°K and testing at either the prestrain temperature or at higher temperatures up to 273°K. EXPERIMENTAL PROCEDURE The polycrystalline a iron specimens used in both the tensile and internal friction tests were 0.033-in. diam ingot iron wires, wet hydrogen treated and re-carburized. A more detailed procedure for processing a 3/16 in. ingot iron rod (nominal wt. pet composition: Fe - 0.013; C - 0.0125; Mn - 0.023; Si -0.005; P - 0.0023; S - 0.11; Cu - 0.004 N) to 0.033 in. diam specimens containing approximately 0.020 wt pet C and no detectable nitrogen with a grain diameter of 0.033 to 0.040 mm is given elsewhere.5 Immediately prior to testing, specimens were solution treated for 15 min at 700o ± 2°C in a static vacuum of less than 50 ?. of Hg and rapidly quenched into an ice-water bath while still enclosed in a 3 mm quartz vial. The internal friction specimens had 8-in. gage lengths and the tensile specimens had 2-in. gage lengths. The wires used as tensile specimens were first run as internal

Jan 1, 1962

By Robert C. Freas, William H. Lane, David J. Krohn

Maysville, Kentucky, is the location of Dravo Lime company&apos;s new 9 070 mt(10,000 tons) per day limestone mine and 2 727 mt (3000 tons) per day calcination plant. This complex has been designed as a unit, and capitalizes on recent technological advances. Geologically the Dravo facility is.located on the eastern flank of the Cincinnati Arch, with the high calcium limestone being found at a depth of approximately 274 m (900 ft). A systems approach has been employed in designing and equipping the mine. This allows for maximum production while maintaining flexibility and versatility. All hydraulic drilling, large LHD equipment, and an extendable mine conveyor system are utilized in a five-part mining cycle. A modular concept modifies the room and pillar system to optimize ventilation. The limestone is calcined in three 5.18 x 61.87 m (17 x 203 ft) KVS rotary kilns with a design capacity of 909 mt (1000 tons) per day of lime per kiln. The kilns are coal fired and equipped with preheaters. Lime storage is provided by three 57 m (186 ft) high concrete silos with a combined capacity of 40 909 mt.

Jan 1, 1976

By David Turnbull

In most reactions involving solids the transformation kinetics may be represented by the combination of two processes —those of nucleation and of growth. For example, Mehl and his coiq-orker in their studies on the transformation of austenite to pearlite in steels have been able to describe the kinetics in terms of the rates of nucleation and of growth. By micrographic examination of their specimens they determined the nucleation rate (rate of appearance of pearlite colonies) as a function of time, of percent transformation, and of temperature. They observed that after an incubation period in which no nuclei are observed, the number of nuclei appearing per unit time per unit of untransformed grain boundary area, increases at an increasng rate with time. When recrystallization rates have been interpreted in terms of rates of nucleation and growth and the rate of nucleation determined, an incubation period followed by an increasing rate of nucleation has also been reported. Among the studies in which this phenomenon has been observed are those of Kornfeld and coworkers3 on cold-drawn aluminum wire, of Anderson and Mehl4 n the recrystallization of aluminum sheet, and of Stanlcy and Meh15 on the recrystallization of silicon ferrite sheet. The existence of an incubation period during which no nuclei are observed does not appear to have been reconciled with the generally accepted Volmer-Becker theory of nucleation in condensed systems. This theory ostensibly requires the rate of appearance of nuclei to be independent of time. Volmer-Becker Theory In order to form a stable nuclcus of a new phase B in a mother phase A, the molecules or atoms of the mother phase must surmount a free energy barrier whose height is determined by the volume free energy change accompanying the transformation and the energy of the surface separating the two phases. The free energy difference between nuclei of various sizes and the molecules or atoms of the mother phase is plotted schematically in Fig I as a function of the radius of the nucleus r. This free energy difference is plotted for two values of the change of free energy per atom, (Jb — ja) accompanying the transformation when the volumes of the two phases are infinite. One of these values of (Jb—Ja) corresponds to a temperature above the temperature To at which the phascs A and B are in equilibrium, and the other to a temperature below To. In order for a nucleus of phase B to be stable at a temperature T² < TO, its radius must be equal to or greater than the critical value r* for which the free energy of formatioil of the nucleus is a maximum, the of phase B having radii equal to or less than r* will be called embryos hfehl and Jetter," in discussing the kinetics of nucleation in solid systems, suppose that embryos of critical size are formed

Jan 1, 1949

By Hsun Hu, R. S. Cline

The annealing behavior and the mechanism of re-orientation during recrystallization of iodide titanium cold-rolled 94 pct have been studied in detail. Results indicate that recrystallization occurs by the nucleation and growth of new grains, as in other common metals. Recrystallization nuclei form by the coalescence of subgraim, and the change in texture as a result of recrystallization is largely due to selective growth among the nuclei formed. The annealing of titanium is characterized by a wide range of overlap of the various stages of the annealing process, which may be responsible for a range of activation energies observed, and for the apparently gradual change in the annealing texture as a function of time or temperature. The deformation and recrystallization characteristics of titanium and zirconium are very similar. In cold-rolled strip, the deformation texture consists of two symmetrically oriented components, each having the basal plane laterally tilted at about 30 deg from the rolling plane and the [1010] direction parallel to the rolling direction. Upon annealing for recrystallization, the change in texture can be described, for simplicity,* as rotations around [0001].2&apos;6&apos;8 According to McGeary and Lustman,&apos; recrystallization occurs in zirconium through normal growth of the subgrains, which they called "domains", without the nucleation of new grains; and the magnitude of rotation around the [0001] axis increases gradually during the progress of recrystallization. If these conclusions were true, the mechanism of recrystallization in zirconium would be basically different from that in most metals, since it is commonly known that recrystallization with reori-entation always involves the migration of high-angle boundaries. In an attempt to clarify the situation, the mechanism of reorientation during recrystallization in iodide titanium cold-rolled 94 pct was studied in detail. The structural and textural changes upon annealing at various temperatures were examined by optical and transmission-electron microscopy, X-ray pole figures, pole density distribution measurements, and micro-beam techniques. EXPERIMENTAL PROCEDURE Material and Specimen Preparation. An iodide titanium crystal bar was are-melted and solidified in a cold-hearth crucible under a purified argon atmosphere. The solidified ingot had dimensions of approximately 3 by 1/2 by 3 in. One face of the ingot was somewhat uneven, but was as clean and shiny as the remaining parts of the ingot. Large grains with a Widmanstatten internal structure were clearly shown on the shiny surfaces, indicating the occurrence of P — a transformation upon rapid cooling from the melt. Analysis of the are-melted ingot indicated C 0.033, N 0.010, H 0.013, 0 0.002 in weight percent, and traces of iron, copper, and silicon as detectable impurities. The ingot was cold-rolled -40 pct to 0.300 in. thick with a reduction of 0.005 in. per pass. The defects on the uneven side of the ingot were then removed by machining. This reduced the thickness to 0.285 in. The piece was then recrystallized by annealing at 800°C for 1 hr in a fused silica boat charged into a fused silica tube furnace under a vacuum of 10~5 mm Hg. To refine the grain size, the recrystallized metal was again cold-rolled 40 pct to 0.170 in., then annealed at 700°C for 1 hr. These treatments yielded a strip with a uniform equiaxed grain structure, having a penultimate average grain diameter of 0.04 mm and a hardness of approximately 90 Dph. Final rolling reduced the thickness from 0.170 to 0.010 in., corresponding to a reduction of 94 pct. The strip was rolled in both directions by reversing end for end between passes. Surface lubrication was provided by oil-soaked pads attached to both rolls. Specimens of 1 in. length (for X-ray examinations) and +in. length (for hardness and microstructure examinations) were cut from the rolled strip, and a width of & in. was cut from the edges of each specimen by a jeweler&apos;s saw. These specimens were then etched in a solution of 10 cu cm HN03, 5 cu cm HF, and 50 cu cm H,O to 0.008 in. thick to remove the surface metal, as well as the distorted metal at the saw cuts, prior to annealing or measurements. To minimize any surface reaction with the atmosphere, all specimens were kept in an evacuated desiccator. Isothermal Anneals. All annealing treatments were conducted in vacuum in a fused silica tube furnace as described earlier. The temperature of the furnace was controlled to within *2"C. The specimen was placed in a fused silica boat, then pushed into the hot zone of the furnace. It took about 5 to 6 min for the specimen to reach the furnace temperature. After the specimen was held at temperature for a desired length of time the boat was pulled to the cold zone of the furnace; the heating-up period was excluded from the isothermal annealing time. Thus, the uncertainty in annealing time is higher for very short anneals, but negligible for long anneals.

Jan 1, 1969

By Richard P. Rothwell

THOUGH coal has been mined in this country for more than a century, no systematic effort was ever successfully made to ascertain the total amount produced. The production of the Cumberland Basin, Md., and the shipments from the anthracite fields of Pennsylvania, have been placed upon record, thanks to the intelligence sand foresight of Mr. C. Slack in the former case, and to the late Mr. B. Bannan in the latter. For some of the years between 1822 and 1842, the production of the Richmond Basin was reported by Mr. R. C. Taylor, but since that date till the author undertook this work it was impossible to obtain any statement of the production of this field. A few of the newer fields, such as that of Mt. Diablo, Cal., have been fully reported, and a few of the newer States have also had this service performed by some intelligent private individuals.; but no statistics of coal production have ever been collected either by the State or General Government, if we except the returns for the years 1869-70 of the census report. During the year 1875, by great exertions, I succeeded in obtaining, and July 3d, 1875, gave in the Engineering and Mining Journal what, "though not an accurate statement of our coal production," was " by far the most full and reliable that had ever been published." Though that report showed the production of bituminous coal to be 23,630,094 gross tons, or about six million tons more than had ever before been reported, it was in reality two and a half million tons below the actual output. The more full returns I obtained for 1875 gave many figures for 1874

Jan 1, 1877

By Henry N. McCarl

Lightweight aggregates include a variety of mineral and rock materials used to provide bulk in concrete building units (block), light- weight structural concrete, and precast concrete units, as plaster aggregate, insulating fill, and other structural and/or insulation purposes. They are distinguished from other mineral aggregate materials by their lighter unit weight- 80 to 100 pounds per cubic foot (pcf) or less for loosely packed lightweight aggregates as compared to 125 pcf or more for crushed stone, sand, gravel, air-cooled slag, and other more common mineral aggregates. The various lightweight aggregate materials may be classified into four groups as follows: 1) Natural Lightweight Aggregate Materials-prepared by crushing and sizing natural rock materials such as pumice, scoria, tuff, breccia, and volcanic cinders. 2) Manufactured Structural Lightweight Aggregates-prepared by pyroprocessing clay, shale, or slate in rotary kilns or on traveling grate sintering machines. 3) Byproduct Lightweight Aggregates-prepared by crushing and sizing foamed and granulated slag, cinders, and coke breeze. With the exception of processed slag, this group is becoming less important as time passes. 4) Manufactured Insulating Ultralight- weight Aggregates-prepared by pyroprocessing ground vermiculite or perlite. This chapter will focus on the use of natural lightweight aggregates and manufactured insulating ultralightweight aggregates, and both the production and use of manufactured structural lightweight aggregates with some comments on byproduct materials. Detailed discussion of the production and use of both expanded and air-cooled slag is presented in a separate chapter in the utilization section of this volume, and there are separate commodity chapters on vermiculite, perlite, pumice, and volcanic cinders. Discussion of the commodities covered elsewhere in the book will be limited to observations on their utilization and relation to other lightweight aggregate materials. All materials considered as lightweight aggregates are derived from some initial natural raw material. While historical definitions have included such organic materials as straw and peat as lightweight aggregates, the discussion in this chapter will restrict itself to lightweight aggregates derived from mineral or rock materials. Thus while the actual lightweight material in use may be a manufactured product, it is derived from an ore or raw material that is obviously a mineral resource. In this context, then, the reserves of raw materials for lightweight aggregate use may include iron ore and flux stone (the components of blast furnace slag) as well as coal (the raw material from which cinders are derived) as well as those clay, shale, and slate deposits that display the characteristics of bloating or controlled expansion when subjected to elevated temperatures (1600 to 2400°F.).

Jan 1, 1975

By John S. Brown

IN 1925 the writer undertook a detailed statistical study of all producing areas in the Joplin district as a basis for evaluating programs and measuring objectives. For this purpose, the published figures in the yearly volumes of Mineral Resources were used, supplemented for earlier years by publications of the Missouri Geological Survey and other local and less official sources. When all else failed, the available data were projected backward to hazard a reasonable guess as to the unrecorded early output of important areas. Fortunately, the proportion of such prehistory production is not a large factor in any of the totals. These results were used during the next few years to measure the relative importance of various producing areas and to predict the peak period of development of the all-important Picher field. For the purpose of this review, the charts have been completed to the end of 1950. During World War 11, the U. S. Bureau of Mines became interested in a similar study and issued comprehensive statistical tabulations of data up to 1945 ( Info. Circular 7383), which have been checked against the figures used herein. This tabulation, however, does not include all the earlier data used by the writer nor does it offer any estimates of the wholly unrecorded era in the beginnings of the earlier camps. The area covered in this study is shown in Fig. 1 on which are indicated the relative location and approximate outlines of the principal producing camps. This also shows the approximate yield to date of each major camp in terms of combined lead and zinc concentrates. The output of zinc concentrates is roughly seven times that of lead. Hence, the economy of the district has depended primarily on the price of zinc, with lead as an important byproduct. Over much of the productive period, lead concentrates averaged about twice the value of zinc concentrates per ton, and in certain mines or areas the proportion of lead to zinc was substantially above average. The Joplin district is largely flat prairie but is partly moderately dissected, partially wooded land with a relief generally less than 100 ft. The rocks are almost flat-lying, nearly parallel to the surface, and the chief ore formation is the Mississippian Boone limestone, including its cherty phases. This formation either outcrops in the producing areas or is covered by a thin veneer of Pennsylvanian shales. Virtually all the ore occurs within 400 ft of the surface, and a large part at less than 300 ft in depth. Most of the land was divided into small farms or town lots before mineral development; tracts seldom exceeded 160 acres, and averaged considerably less. Mineral rights followed the surface ownership, segregation was rare, and a system of leasing for mineral development became well established early in the region&apos;s history, many landowners deriving small to sizable fortunes from royalties. Because of the shal-lowness of the ore and other factors, prospecting and mining was cheaper than in almost any comparable mining district in the United States. This situation, coupled with the widely divided land ownership, offered a fertile field for promoters and speculators and led to the rise of many small mining concerns. Only in its later history, under stern economic compulsion, has control tended to centralize in a few companies. Under these conditions, any important new discovery or successful development had much the effect of a gold rush or an oil boom. Every property in the area was leased quickly, promptly drilled, and, if ore was found, it was soon on the market. Many companies and individuals participated, and the average producing lease-hold probably was about 40 acres in extent. Any important field thus was attacked by anywhere from 10 to 100 or more producers. Production zoomed, eventually steadied or wavered, and ultimately subsided, leaving a desolation of tailings mountains, cave-ins, empty housing, and wreckage. The object of this paper is to depict the pattern of this process, so far as metal production is concerned, and to note the way in which it reacted to economic and political pressures. Production Charts In Fig. 2 is charted the production record, in tons of lead and zinc concentrates combined, of eight of the principal camps, which together account for approximately 99 pct of the total district production, over the years from 1870 to 1950. This period covers all but the very minor beginning of mining history. Two important camps are divided by state lines; hence, it has been necessary to combine production records for the two portions, based on estimates that may be slightly in error. Certain camps are sub-dividable into important units for which separate figures are available in whole or in part and have been charted as fractions of the major unit. The corresponding price of zinc is shown above all the charts. Three camps, Aurora, Neck City, and Galena, show a remarkably symmetrical graphic pattern, which is interpreted as the norm. The curves rise steeply to a peak, level off for an irregular interval, and then drop sharply to zero on a slope corresponding roughly to that covered by the initial rise. The three portions of these charts seem appropriately characterized by the designations of youth, maturity, and decline. On the whole, with some irregularities, the production in each of the three periods seems to be almost equal. A fourth camp, Granby, fails to conform to the normal pattern. It exhibits a very long period of reasonably uniform, stabilized production corresponding to maturity, followed by a rather precipitate decline. Its youth is hidden in the era of prehistory. This habit of steady, long-continued production at an even keel is attributable to the fact that this camp, more than any other, was controlled largely by a single principal owner at any given period over most of its history and this permitted the imposition

Jan 1, 1952