Search Documents

By Bruce Chalmers, D. C. Larson

Aluminum crystals with longitudinal-axis orientations of (111) . (110), and (100) were deforined in tension and annealed. The conditions of deformation were controlled so that the re crystallization nuclei originated in either the heavily deformed regions at saw cuts {artificial nucleation) or in the lightly deformed matrix (spontaneous nucleation). The artificial-nucleatioln experiments showed that in lightly deformed (110) and (100) crystals low-angle twist boundaries are most mobile, while in (111> crystals and heavily deformed (110) and (100) crystals high-angle tilt boundaries with near (111) rotations are favored. The spontaneous-nucleation experiments showed the existence of preferred orientations in the (111) crystals. The nonrandomness of the grain orientations is quantitatively determined through a comparison with the results which would he obtained from a randowl set of grain ovientations. PREVIOUS recrystallization studies have been performed on single crystals deformed in tension.1 7 The crystals used in these studies usually had random tensile-axis orientations and the extent of deformation was not a primary consideration. The present study concerns the recrystallization of single crystals with tensile-axis orientations of (Ill), (110), and (100). The emphasis of this work is on the influence of the tensile-axis orientation and the degree of deformation on both the nucleation and growth processes. The multiple-slip orientations were chosen because secondary slip or slip intersection promotes nucleation.1,5,8 These crystals recrystallize at lower strains than the crystals which are oriented for single slip. Also, the greatest variation in deformation behavior is exhibited by the multiple-slip orientations. The stress-strain curves for crystals with tensile-axis orientations of (111) are higher than the stress-strain curves for poly-crystals, and the stress-strain curves for crystals with tensile-axis orientations of (100) are lower (at large strains) than the stress-strain curves for the crystals which deform initially in single slip.g The recrystallization nuclei originated in either 1) the homogeneously* deformed matrix of the crys- tals or 2) the heavily and inhomogeneously deformed regions at saw cuts. The nuclei will be referred to hereafter as spontaneous and artificial nuclei, respectively. The two terms do not imply a difference in the nature of the nuclei; they imply simply a difference in the mode of introduction of the nuclei. During spontaneous nucleation very few (always less than ten) grains nucleate, while during artificial nucleation large numbers of grains nucleate. Only a fraction of the artificially nucleated grains penetrate very far into the deformed matrix during annealing. The grains that penetrate the farthest into the deformed matrix will be referred to as the dominant grains. EXPERIMENTAL PROCEDURE The thirty-five crystals used in this investigation were grown from the melt in milled graphite boats at a rate of 1.6 cm per hr. The crystals had dimensions of approximately 6 by 12 by 80 or 6 by 6 by 80 mm and the aluminum was of 99.992 pet purity. The as-grown crystals were annealed at 610°C for 24 hr and furnace-cooled. They were then heavily etched and electropolished in a solution of five parts methanol to one part perchloric acid. The crystal orientations were obtained by back-reflection Laue photographs and were accurate to ±2 deg. The tensile-axis orientations were (loo), (110), and (111). Two of the side faces of the (111) crystals were (110) lanes. The (110) crystals had both {100) and {110) side faces and the (100) crystals had (100) side faces. The crystals were deformed at a strain rate of 0.003 per min. Shear stress and shear strain were obtained by multiplying and dividing the tensile stress and strain, respectively, by the Schmid factor, m. For the (111) crystals m = 0.272 and for the (110) and the (100) crystals m = 0.408. The Schmid factor is effectively constant during deformation for all orientations. The deformed crystals were sawed into 1-in.-long specimens while the crystals were totally enclosed in a graphite boat. The sawing was performed very carefully in order to limit the plastic deformation to the sawed regions. The specimens were electropolished in the solution mentioned above to remove the sawed-end deformation as well as controlled amounts of surface material. A special stainless-steel grip was used to hold the specimens during the electropolishing treatment. The gripping faces were flat, with no teeth, to prevent the introduction of extraneous de-

Jan 1, 1964

By David B. Scott

When mining operations were first instituted in the mines of the Miami Copper Co., at Miami, Ariz., the relatively hard character of the ground in the western section of the property made it seem advisable to use a wide shrinkage stope and pillar system. The system as finally evolved was applied to the mining of 2,300,000 tons of ore by the use of stopes and pillars each 50 ft. in width. Development, mining and extraction of this reserve has been continuously in progress since 1910, and the final stages of extraction are now reached. A complete survey of all phases of this system can therefore be made. Modification in working methods was obviously necessary, and the system to be described is believed to be typical of the best features. Development The preliminary work had three main objectives: The opening of a haulage level, the construction of a drawing-off level, and the driving of sublevels for use in stoping. In addition to these, some extra sublevel drifting was necessary to determine exactly the boundaries of the orebody, the general outline having been determined by churn drilling. This development was based on the requirements of stopes 50 ft. wide, with pillars 50 ft. wide between each stope. The length of these units varied from 200 to 500 ft.. Haulage Level The tramming level was 50 ft. below the floor of the stopes, and the tramming lines were run parallel with the long axis of the stopes. These lines were also beneath the middle of the stopes and pillars. Each line therefore served one stope or one pillar, this arrangement making it possible to load along an entire stope without switching or uncoupling. This advantage is apparent principally during the process of stoping when rapid drawing of excess broken ore is desirable. Furthermore, the arrangement of the drawing-off level chutes at 25-ft. intervals, as shown

Jan 1, 1917

By E. C. W. Perryman

IN spite of the large amount of work which has been carried out on the recrystallization of aluminum and its alloys, there has been no complete investigation of the recrystallization characteristics of A1-Mg alloys. The most complete investigation is that reported by Bungardt and Osswald' who, working with commercial-purity materials, found that the temperature both of beginning and of complete recrystallization increased with magnesium content up to about 2 pct Mg, then decreased with a further increase in magnesium up to 5.0 pct, and thereafter increased again. Michaud and Segolz working with 99.93 pct A1 also found the temperature of beginning of recrystallization to decrease as the magnesium content increased from 2.13 pct to about 4.5 pct. Chossat3 using aluminum of 99.99 pct purity found that 0.12 pct Mg had no effect but that 0.4 pct Mg increased the recrystallization temperature by about 30°C. That no effect was found for 0.12 pct Mg does not agree with the later results reported by Demer and Beck4 who found that 0.025 pct Mg in 99.99 pct A1 increased the time for complete recrystallization and furthermore increased the activation energy for the recrystallization process. Kratz" using 99.997 pct A1 found that 0.5 pct Mg increased both the temperature of beginning and of complete recrystallization by 100°C. Chadwick and Hooper" working with commercial-purity material found that 1 pct Mg increased the temperature of complete recrystallization by about 40 °C for cold reductions in the range 17 to 72 pct. With smaller amounts of cold work produced by stretching (10 pct strain), they found no significant effect of magnesium. The latter result agrees with that obtained by Williams and Eborall' who found no effect of 2 pct Mg on the recrystallization temperature of commercial-purity aluminum strained 10 pct or less by stretching. Experimental Procedure Material Used: The chemical analyses of the materials used throughout this investigation are given in Table I. Fabrication: The alloys were cast in iron molds which had been washed thoroughly with alumina. After scalping, the ingots were annealed for 16 hr at 450°C, pressed, annealed at 450°C for 16 hr and hot rolled to 0.25 in. After hot rolling, the slabs were alternately annealed and cold rolled to 0.036 in. Cold-rolling reductions between intermediate anneals were kept at about 30 pct and a high intermediate annealing temperature of 450°C was used so as to obtain, as nearly as possible, similar starting grain sizes for the different materials. All intermediate anneals were done in a salt bath and were followed by cold-water quenching so as to retain all the magnesium in solid solution. The final cold reductions investigated were 20, 30, 40, 50, 60, and 80 pct. The initial grain sizes, that is, the grain size before the final cold reduction, were all very similar. Annealing Procedure: Specimens, 1 in. sq, were cut from the 0.036 in. sheet and annealed in a salt bath, the temperature of which was controlled to k2"C. Separate specimens were annealed for different times at 350°, 375", 400°, and in one or two cases at 415°C and after annealing were quenched in cold water. The time taken for a specimen to reach temperature was approximately 5 sec. Metal-lographic examination after annealing showed that no precipitation of Mg+413 occurred during cooling. Procedures Used for Determining Recrystallization Characteristics: All specimens were electrolyti-cally polished and etched by the method described previously1° and polishing was continued until about 0.002 in. had been removed from each side of the specimen. Using this technique, the smallest recrys-tallized grain which could be observed with cer-

Jan 1, 1956

Today there is unparalleled opportunity for constructive effort in the national mineral economy on the part of the Land-Grant colleges and universities. The matter is too important to be pushed aside. It is inevitable that in the aftermath of World War II, conscientious Americans the country over should want to take stock of national resources. Attention is now centered, as never before, on our mineral potentialities. Opportunities and responsibilities are unparalleled and a condition exists which will not occur for another generation. Mineral industries educators cannot pro- vide the answer without taking stock of its component parts, organizing, planning, and taking action in a real dynamic sense. The services encompassed by the various fields of mineral industries must be utilized to help in the solution of problems provided by the international emergency, the country's needs, the people's needs. Mineral industries colleges have a vital role in technical aid to backward countries through foreign student programs, especially in the Latin Americas.1 By helping them to help themselves develop and utilize their resources to the fullest, we will be helping ourselves. One day they may be a Godsend in a solution of the American demographic problem. They may be prepared to

Jan 1, 1950

The fate of generations yet unborn lies in man's hands. Shall it be prosperity, a high standard of living, and the development of spiritual values; or ruin, misery, and a reversion to jungle law? World affairs move in high gear, at high tension, in many directions. Each nation fears the other fellow- races, crosses the white line on curves, skids, takes its half in the center; and the devil take the hindmost. For one, the United States is on the horns of dilemma; it must insure a flow of raw materials of industry and world-wide markets in order that the American people may maintain high standards of living, but the commitments of the United States cannot be fulfilled without trimming present standards of comfort and convenience back to the level of perhaps a quarter of a century ago. A way must be found to retreat without anarchy at home as well as abroad. Everything is relative and all things change, and change is the essence of civilization. It is now clear that man has not kept pace with changes of all kinds, some of them overnight, during the past 50 years. Conventionality has led to stagnation; man now seeks learning of all kinds at an accelerated pace, but men should not be educated beyond their native intelligence for they must be able to apply their education. There must be a resolute action now on 10 great challenges in regard to conservation of human and ma-

Jan 1, 1950

Professor Somasundaran has given an excellent presentation of the numerous problems which remain to be solved before the selective aggregation of fine particulates is likely to see broad commercial application in the beneficiation of mineral fines. However it is useful, I think, to reiterate some of the major problem areas. The over-riding factor which has limited the development of selective aggregation techniques is that processes such as coagulation and flocculation tend to be inherently non-selective. Conditions which favor the aggregation of one kind of fine particles usually favor the aggregation of all kinds of particles. As Professor Somasundaran has pointed out, the state of aggregation of a fine-particle dispersion is primarily determined by the forces of interaction between the individual particles. In most systems, the dominant forces are: 1. van der Waals - London Dispersion forces between the particles themselves 2. electrical double layer forces 3. steric forces between adsorbed layers on the surfaces of the particles. The London Dispersion forces between like particles are always attractive, but for dissimilar particles dispersed in a fluid medium can, in some cases, lead to a net repulsion. Electrical double layer forces always lead to repulsion between like particles but can, again, cause either attraction or repulsion for dissimilar materials. The steric forces, which are by far the least understood of the three types, can also lead to attraction or repulsion depending on condi-

Jan 1, 1979

By J. D. Mote, A. Rosen, J. E. Dorn

The effect of strain rate and temperature on the critical resolved shear stress for (1100) [1120] prismatic slip was determined for the intermediate hexagonal phase containing about 67 at. pct Ag and 33 at. pct Al. Whereas the flow stress increased only slightly as the test temperature was first decreased below room temperature, a rapid increase inflow stress was obtained with yet greater decreases in temperature from about 240" to 4°K. The effect of both temperature and strain rate on the flow stress over the low-temperature range could be completely rationalized in terms of the Peierls mechanism when the deformation is controlled by the rate of nucleation of pairs of kinks. A few years ago Mote, Tanaka, and Dorn1 observed that the critical resolved shear stress for prismatic slip of a 67 at. pct Ag plus 33 at. pct A1 hexagonal intermediate phase by the (1100)[1120] mode decreased precipitously as the test temperature was increased from 4" to about 160°K. Their results for both basal and prismatic slip are given in Fig. 1. It is obvious that only the flow stress for prismatic slip is strongly temperature-dependent, whereas the flow stress for basal slip is independent of temperature. If the temperature dependence of the flow stress were primarily due to interstitial impurities, it might be expected that they would influence the flow stress for basal slip as well. Since the activation volume at 115°K for prismatic slip was determined to be about 15b3, where b is the Burgers' vector, this thermally activated deformation process was tentatively ascribed as being due to the Peierls mechanism. But the various analyses of the Peierls mechanism then available as formulated by Seeger2 and also by Lothe and Hirth3 did not agree well with the experimental data. Since that time a more realistic theory for the operation of the Peierls mechanism under conditions where the strain rate is determined by the rate of nucleation of pairs of kinks has been presented by Dorn and Rajnak.4 The present investigation was, therefore, undertaken in order to provide the essential data for a careful check on the agreement between this theory and the low-temperature deformation by prismatid slip of the above-mentioned Ag2A1 intermediate phase. EXPERIMENTAL TECHNIQUE Single-crystal specimens so oriented that the [1120] direction and the normal to the (1100) plane were at 45 * 2 deg to the tensile axis were grown from the congruent melting composition of about Ag2Al for the intermediate hexagonal phase by the

Jan 1, 1964

By R. A. Sharma, F. D. Richardson

Manganese oxide acitivities and sulfide capacities have been measured at 1650°C in mixtures of MnO + A1203 and MnO + SiO2 - Al2O3. Sulfide capacities have also been measured at 165O0C for melts of MnO + SiO2, MgO + SiO2, MgO + SiO2 + Al2O3, MgO + MnO + SiO2, and SiO2 + Al2O3 and for crystalline CaO. The activity coefficients of the sulfides of manganese and magnesium have been derived where possible. It looks as though the activity coefficients of sulfides are greatest at compositions where the free energies of formation of the silicate mixtures have their maximum negative values. The amphoteric nature of alumina is reflected in the results for the binaries and ternaries in which it is present with silica. The limiting solubility of CaS in CaO at 1650°C is 6.3 x 10-4 mole fraction. THE activities of manganese oxide have been measured in a variety of silicate and aluminate melts by use of the equilibrium (MnO)slag = [Mn]pt .½O2 [l] and the experimental techniques described previously.' Sulfide capacities (CS = wt pct S (PO2/PS2)½) have also been determined in a series of melts, by use of an established method2 which exploits the equilibrium (O°) + ½S2 = (S") . ½O2 [2] If CS and the activity of a metal oxide are known in a melt, the activity coefficient of the metal sulfide can be calculated by use of the equilibrium constant K, for the pure phase reaction MO i ½S2 = MS + ½O2 [3] The activity coefficient of the sulfide is then given by the equation

Jan 1, 1965

By D. E. Thomas, C. E. Birchenall

ALTHOUGH Eoltzmann gave a mathematical solution for the diffusion equation (for planar diffusion in infinite 01. semi-infinite systems only) in 1894 allowing for variation of the diffusion coefficient with a change in concentration, it was not until 1933 that this solution was applied to an experimentally investigated metallic system. The calculation was carried out by Matano' on the data obtained by Grube and Jedele3 for the Cu-Ni system. Since that time concentration dependence of the diffusion coefficient has been demonstrated for many pairs of metals. However, the nature of this dependence has never been fully elucidated. Many investigators have suspected that these variations could be related to the thermodynamic properties of the solutions, one of the earliest explicit statements being contained in a discussion of irreversible transport processes by Onsager' in 1931. Development along these lines has been greatly retarded by the lack of reliable data on the variation of tliffusivity with concentration, the paucity of the thermodynamic data for the same systems at the same temperatures and compositions, and an incomplete understanding of the relation of the thermodynamic properties of the activated state for diffusion to the bulk thermodynamic properties. The last factor has been discussed by Fisher, Hollomon, and Turnbull.5 In many instances where data exist, it is difficult to know which are acceptable. This problem probably applies more strongly to diffusion data than to activity measurements. For instance, four sets of observers"-" have reported self-diffusion coefficients for copper. The average spread between extreme results is a factor of about four, though the individual sets of data are self-consistent to about 20 pct. Thus one or more factors are out of control, at least in these experiments, making estimates of internal error unreliable. The most reliable diffusion data in most systems have resulted from the use of welded couples with a plane interface from which layers for analysis are machined parallel to the interface after diffusion. The layers are analyzed, and the result is a graphical relation between distance and concentration, usually called the penetration curve. Given the same set of analytical data and distances and following the same procedure in computation, different observers will generally produce diffusion coefficients which vary appreciably, especially at the extremes of the concentration range. Experiments must be carefully designed so that the precision is good enough to answer a particular question unequivocally. In the first calculation of the dependence of the diffusion coefficient on concentration in the metallic solid solution Cu-Ni, Matano found that the coefficient was insensitive to concentration from 0 to 70 pct Cu, after which it rose more and more steeply to some undetermined value as pure copper was approached.' The same behavior was reported for Au-Ni, Au-Pd, and Au-Pt.* The data used were those of Grube and Jedele which were very good at the time, but are not considered particularly good by present standards. Furthermore, the method of calculation makes the ends of the diffusion coefficient-concentration curve unreliable. For better reliability, the high copper end of the curve has been checked by incremental couples, where the concentration spread is 67.7 to 100 atomic pct Cu. The implication of the curves calculated by Matano was that diffusion is very concentration sensitive in one dilute range of this completely isomorphous system and hardly at all in the other. Matano's result is confirmed. Later Wells and Mehll0 published data on diffusion in Fe-Ni at 1300°C, which represent a thorough test of the shape of the concentration dependence curve. They ran couples with the following ranges of nickel concentration: 0-25 pct, 1.9-20.1 pct, 0-20.1 pct, 20.1-41.8 pct, 0-99.4 pct, and 79.3-99.4 pct. Although the trend of the data indicates an S-shaped concentration dependence, their curve was drawn to the pattern set by Matano. Their original data have been recalculated for the 0-99.4 and 79.3-99.4 pct couples. Wells and Mehl's points and two independent recalculations from the raw data are plotted in Fig. 1. What appears to be the best curve is drawn through them. This curve shows little sensitivity to composition in both dilute ranges with a strong dependence at intermediate composi-tions.? Similar experiments on the Cu-Pd system are reported here at temperatures where solubility is unlimited. These lead to the same type of concentration dependence for the diffusion coefficients as was found upon recalculation of the data for the Fe-Ni system. Experimental Procedure Cu-Pd: The concentration dependence of the diffusion coefficient may be determined by the use of

Jan 1, 1953

By D. D. Button, L. D. Jaffee

INTEREST in the use of graphite as a high-temperature engineering structural material has recently increased markedly. However, actual use of this material has been limited, in part because information about its high-temperature mechanical properties has been lacking. The information needed includes not only reliable values for the properties, but also how to control these properties. Malmstrom, Keen, and Greenl have reported on the tensile and creep properties of some graphites above 2700° F (1500°C). They observed measurable creep under tensile loading at 4000 OF (2200 °C) and higher, with elongations of about 7 pct at 4500°F. Their typical elongation-vs-time curve showed the normal three stages of creep found for many metals at elevated temperatures. The specimens used were heated by passing an electric current through them. This method of heating caused a significant difference between the surface and axis temperatures, and may have affected the results. More recent work by kattus, in which the specfinens were also heated by their own resistance, showed very little plastic deformation for either slow or fast tensile testing or for creep testing. Work at this Laboratory, already reported,3 showed that for temperatures above 4500 "F and under conditions of slow tensile loading some commercial graphites exhibited elongations up to 20 pct. The work reported here is the continuation of a study of the tensile creep behavior of some commercially available synthetic graphites at temperatures up to 5300°F, and is preliminary to a more systematic investigation of the variables governing the high-temperature mechanical properties of graphite. MATERIALS TESTED The tests were conducted on six blocks from four lots of synthetic graphite bearing four different commercial-grade designations. These blocks were selected because their tensile stress—strain properties had been determined in previous work.3 Table I pre- sents the available information, supplied by the producers, on the processing of these materials. Also included in this Table are the densities and the tensile strengths at room temperature and 4500°F determined by the authors. EXPERIMENTAL TECHNIQUE The furnace used to heat the specimens for testing is shown in Fig. 1. The heating element was a graphite tube, 3-in. OD by 2 1/2 in. ID by 24 in. length. A spiral was cut into the 6-in. center portion of this tube to provide a high-resistance sec-

Jan 1, 1961

By N. A. Ziegler

THE present publication is a continuation of the work on gas analysis, described in a paper presented before the Institute of Metals Division a year ago.1 While that paper was largely descriptive in character, dealing with the various parts of the apparatus and method of operations, the present one gives numerical data obtained as a result of a series of experiments with iron-carbon alloys. The apparatus and the methods applied are essentially the same as previously described, changes being only in minor details. Attention should be called to the fact that in the present work we are dealing with the gaseous mixtures obtained as a result of vacuum melting of various ferrous alloys. It should be understood that when the terms "degasified sample" and "products of degasification" are used, they refer to the sample remaining after the vacuum fusion of the alloy and the gaseous products removed therefrom, respectively. The writer does not wish to create the impression that the metallic products of this process are absolutely free from any gaseous elements, nor that the gases obtained are present as such in the original sample. These two points are not yet definitely known and are subjects for future investigation. The point, however, which has been established beyond doubt, is that all the gases dealt with come from the metallic charge and are present either in the charge as such, or are produced as a result of chemical reactions going on within the charge. The suggestion that the gases are due to the reactions between the metallic charge and the refractory materials has no valid basis.

Jan 1, 1929

By Michael J. Messel

OF the various minerals that occur in fibrous form known as asbestos, chryso-tile is the variety most in demand for commercial uses, and, last year, over 683,000 tons of the various grades were produced in Canada and United States, exclusive of African and Russian production, which figures are uncertain. Production has not been able to keep up with the increased demand, and an acute shortage exists. Canada, Russia, and Africa are still the most important producers. However, Russia consumes most of its production at home and exports very little. The United States consumes over 60 pct of the total production and produces only about 4 pct of the total from deposits in Vermont and small quantities from Arizona. This paper will review mainly, some of the more recent developments concerned with the extraction and processing of this fibrous mineral for various industrial uses, such as textiles, insulation, building materials and brake linings. Four of the more important factors that have influenced recent developments are: 1. The lack of discovering and developing new deposits of any important size to supply the increased demand. 2. Rapid postwar expansion of industrial uses, especially in asbestos cement products, together with in-rreased manufacturing facilities. Euro-peal) countries are again back on the market with their demand. 3. The ability of manufacturers to develop their technique of blending fibers and obtaining more utility value out of each ton of fiber, together with the utilization of shorter grades of fiber to obtain equally as good products. In the past, many manufacturers were wasteful in their use of fibers. 4. The struggle for reduced operating costs, in face of increased wages and prices of supplies, together with the necessity, at some mines, to change the method of mining from open quarry to underground. Most of the recent capital invested in the asbestos mining industry has gone into more efficient extraction of the fibers from the existing ore, especially in the recovery of the shorter grades. There has been very little new plant expansion. Progress in the utilization of shorter fibers has been so far reaching that some of the mining companies are retreating present tailings as they leave the mill, and others are considering retreating of the old tailing dumps for recovery of fibers that, until recently, were not saleable and were discarded as part of the tailing. Many of these dumps contain much valuable fiber from days when milling was very inefficient. It might be appropriate to mention here that the present known asbestos reserves of proved commercial value (excluding Russia) are being depleted at an alarmingly rapid rate, about 10,000,000 tons of ore is being mined annually. No new deposits have come into production during the last 15 years, with the exception of certain deposits in Africa, which are the most promising, and minor developments in Canada, Venezuela, Cyprus, Australia, and Brazil. The African deposits are the only ones that hold promise of developing large reserves. Unless new deposits are developed, in twenty years or maybe sooner, the supply picture will not be a very bright one. Stimulated by the acute shortage, increasing fiber prices and technical developments, many new areas are being prospected in Canada, United States, New Zealand, Newfoundland, South America, Europe, Africa, and China. From information now available, it appears that no real progress has been made in duplicating this rare development of nature by producing synthetic asbestos. The most promising experiments were carried out at the University of Leipzig, but they seem far from practical. There has been marked progress in fiber glass manufacture, but so far, it has replaced asbestos only in very few instances for minor uses. Asbestos ore and the fiber it yields are different in some respect at each mine and vary usually in the following: 1. Percentage of fiber content by weight to the gangue. 2. Variations in proportions of long and short fibers, some deposits being predominantly long fiber and others short fiber. 3. The hardness of the rock in which the fiber occurs. 4. The nature of the fiber, as to

Jan 1, 1950

By Joseph L. Jernegan

The Whale Lode occurs in the main range of the Rocky Mountains, Park County, Colorado Territory, at Hall Valley. It has been opened up and worked to some extent by the Whale Mine, situated some 11,300 feet above the level of the sea. The mine, with 700 feet of the lode on either side of the discovery shaft, is the property of the Hall Valley Silver-Lead Mining and Smelting Company. The adjacent country rock is a compact, fine-grained gneiss; its general strike is about north and south, dipping steeply to the west. In the immediate vicinity of the mine, the strata are very nearly vertical. The gneiss incloses numberless veins of a reddish granite, in which the feldspar largely predominates over the quartz and mica, the latter oftentimes being scarcely perceptible. As a general rule these granitic veins seem to more frequently follow the lines of stratification of the gneiss than otherwise. They are of varying width, some large, some small; the larger are from 5 to 6 feet wide. Gash veins of feldspar and quartz are also of very frequent occurrence. The general trend of the lode is about northeast. and southwest, intersecting the country rock at about an angle of 45 to its stratification. It dips to the northwest at an angle of 65. I am unable to state accurately how far this lode has been traced upon the surface, but it is at least well known to extend entirely through the mountain upon which the mine is situated, and is traceable over the ridge by a hollow extending for some distance along the surface, in which the lode crops out. This hollow in the surface rock has probably been formed through decomposition of the vein matter by atmospherical influences. The width of the crevice is variable, generally between 5 and 10 feet; the pay vein varies from an inch, or less, to 36 inches. The vein is generally accompanied both on foot and hanging walls by a whitish, semi-decomposed fock, composed of quartz and decomposed feldspar, and in some places—where the process of decomposition has not reached as advanced a stage—a lightgreenish or black mica. This rock, therefore, is in places composed of all the constituents of gneiss, and is undoubtedly nothing more or less than the same in a decomposed condition. It is often very strongly impregnated with iron pyrites, generally crystallized in minute cubes, and it is probably owing to the presence of this min-

By James Hyslop

MECHANIZATION of American coal mining continues to make rapid progress. Economic pressure will compel abandonment of manual methods wherever possible and will also provide the incentive needed for the improvement of machines and mining systems. However, rapid progress may be made along strictly technological lines and at the same time much slower progress in approaching maximum productivly and efficiency. One can well ask, just how efficient are mechanized mines, and to what extent is productivity affected by the mental attitude of management and workers?

Jan 1, 1946

By Öner Yücel, M. Zeki Dogan, A. Metin Ger

Technical and financial feasibility studies conducted at the Middle East Technical University, in Ankara, Turkey, have revealed that a 400 km long prospective slurry pipeline between Hasançelebi and Iskenderun could efficiently and economically transport iron concentrates, with a size of 55%-325 mesh and of amounts varying between 0.25 and 8.0 million tonslyear. Particularly for annual throughputs above 500,000 tons, favorable results have been obtained regarding the processing of the ore, the applicability, the transport cost, and the foreign ex- change currency savings.

Jan 1, 1980

By E. Martinez, M. L. Hollander

Sulfurization of copper oxides was investigated using differential thermal analysis (DTA) and thermal gravimetric analysis (TGA). When mixtures of cuprous oxide and sulfur were heated, the surface of the cuprous oxide was converted to cupric sulfide at the melting point of sulfur (119°C); additional sulfuriza-tion took place when the sulfur vaporized above 200°C. Cupric oxide also reacted with sulfur to form cupric sulfide but the starting temperature was approximtely 225°C. When the cupric oxide and sulfur were physically separated, sulfurization still occurred indicating a reaction with the vapor phase of sulfur. Sulfurization was obtained in runs with cuprite, chrysocolla and basic copper carbonate. Further decomposition of cupric to cuprous sulfide was noted at somewhat higher temperatures. The DTA-TGA data made it possible to set up postulated reactions in each system. These techniques were found to be well suited for studies of this type. Because of the difficulty encountered in flotation of many metallic oxide minerals, efforts have been made to find suitable reagent combinations to sulfi-dize these minerals in the flotation circuit. Recently Bautista and Sollenberger,1 using a different approach, showed that the surfaces of many oxide minerals can be converted to sulfides by heating them with sulfur to temperatures between 150° and 225°C. This technique was effective even with chrysocolla, a mineral which is very difficult to sulfidize. The primary objective of the present study was to obtain information on the reactions between the oxide minerals and suIfur. A better understanding of the mechanisms involved might prove useful in pointing the way to improvements in the process. A secondary objective was to demonstrate the value of thermo-analysis in investigations of this type. Bollin and Kerr2 have reported the use of a modification of differential thermal analysis to study the thermal reactions which occur on heating elemental constituents in a closed system to synthesize copper sulfides and iron sulfides. Differential thermal analysis (DTA) was used to detect enthalpic changes as mixtures of minerals and sulfur were heated. The DTA indicated the temperatures at which reactions started and whether they were exothermic or endothermic. Weight change data were obtained by thermal gravimetric analysis (TGA). These data could often be used to support postulated reactions and to eliminate consideration of other possible reactions. EQUlPMENT Differential thermal analysis (DTA) involves measuring the temperature difference between the sample being tested and a thermally inert reference, generally aluminum oxide, as both are heated at a uniform rate. Series connected thermocouples in the sample and reference are used to detect the temperature differences that occur as the sample undergoes enthalpic changes.3 Crystalline transitions, fusions, vaporizations, dehydrations, decompositions and many solid state reactions can be detected. A DTA unit manufactured by the Robert L. Stone Co., Austin, Tex., was used in this investigation with a temperature rate increase of 10°C per min. The samples and reference were placed in Inconel cups with wells in the bottom into which the differential thermocouples fit, and run in a nitrogen atmosphere. Thermal gravimetric analysis (TGA) measures the changes in weight that a sample undergoes as it is heated. A Chevenard thermobalance converted electronically for graphic recording was used with a heating rate of 5°C per minute. An X-Y recorder plotted temperature on the X axis and weight changes on the Y axis. A flow of 250 ml per min of nitrogen was streamed through the furnace. Samples were placed in a porcelain crucible open at the top, unless otherwise noted. EXPERIMENTAL RESULTS Sulfur: Two sulfur samples from different sources were tested. The DTA of a high purity sulfur and a reagent grade sublimed sulfur are shown in Fig. 1. Nearly all the tests were run with the sublimed sulfur due to the difficulty in grinding and high electrostatic charge encountered with the high purity sample. Sulfur undergoes three endothermal reactions below 200°C. The first is a solid-solid crystalline transi-

Jan 1, 1964

By T. B. Crowe

MucH has been written upon the precipitation of metals from cyanide Solution by zinc. We often read of the many factors that influence precipitation, such as zinc surface, purity of zinc, percentage of lead, temperature of solutions, strength of solutions in cyanide or alkali, etc. -Little do, we hear, however, of the part that oxygen plays in precipitation. Caldecottl says: "As the dissolving of gold is essentially an oxidation process, so its precipitation is one of reduction." All who have studied or worked with cyanide solutions will agree that Caldecott's statement is true.' . In the cyanide work in the mills of the Portland Gold Mining Co., we have always found oxygen to be the greatest enemy to precipitation. Oxygen Antagonistic to Good Precipitation A few years ago, while making some experiments on the effect of pressure upon the dissolving rate of gold from our ores, to prove a point, I made some bottle tests under vacuum. The results were surprising, and showed that under vacuum practically no gold dissolved, which confirmed my belief that Elsner's equation was true and also led me to investigate the amount of dissolved air carried by solutions at atmospheric pressure. The experiment consisted in partly filling an acid-bottle with mill-solution and connecting it by a rubber hose to a vacuum pump. When the vacuum was suddenly applied, a cloud composed of thousands of small air bubbles rose out of the solution, showing qualitatvcily' the amount of dissolved air that was contained in the solution, and also proving that the relief of atmospheric pressure on the solution permitted this dissolved air to escape. In studying literature on the subject, we find Henry's law—"The amount of gas dissolved by a liquid is proportional to the pressure to which the gas is subjected."

Jan 1, 1919

By E. H. Rose

THE question is often pondered whether the flotation process is still an art or has become a science. The fact is that flotation is a science in so many variables that only art can blend them. It is demonstrable that no less than one hundred variables are involved in any flotation operation, most of them immeasurable on a routine basis. The behavior of every one of them is always governed by orderly and unchanging law, as no man can doubt. There is nothing truly indefinite about that behavior; the only indefiniteness is in our knowledge of it, either in general or from hour to hour in the circuit. In dealing with a simultaneous equation in, say, one hundred variables, all not only affecting the outcome to some degree but many influencing each other as well, it is small wonder that the mineral-dressing profession presents a case history of debate and controversial opinion. The statement of the subject of this symposium-a symposium on flotation machines-seems to delimit and define the matters to be considered and at least the general nature of the conclusions sought. Nevertheless, in such a meeting it is not possible to meditate upon all the variables that do in one way or another affect performance of flotation machines. To attempt it would be much like trying to operate a hundred-ring circus. Perverse variables being what they are, one could expect the elephant in ring 36 to squirt a trunkful of water at the tightrope performer in ring 37 to ruin that artist's act, just as our learning to depress pyrite in the early 1920's ruined the act of the formerly faithful old Callows. HONEST DISAGREEMENTS Selective flotation dates from 1922 or 1923, when several plants established their regular flotation operations on a selective basis. Since then, two decades of efforr have gone into the development of better and better flotation machines. Many have come and gone. The competition has simmered down to perhaps a dozen machines, each one of which is staunchly defended by some operators as being the best for their particular jobs, and as scornfully dismissed by at least a few others elsewhere as being positively the poorest for theirs. These disagreements are honest disagreements, honestly arrived at after plenty of sweat. In many a flotation plant, one machine has been tried out against another under conditions as fair as they could possibly be made. Sometimes the results are on a par but more often one machine shows a consistent and unmistakable margin of superiority over the other. In equally honest and enlightened tests, machine A may win over machine B in one place, and machine B over machine A by as great a margin in another. This paper purposes to identify some of the more prominent reasons why this is so,

Jan 1, 1944

By R. H. McLean

Velocity, kinetic energy and shear in crossflow beneath three-cone jet bits may influence cleaning of the bottom of the borehole and the teeth of the bit. Laboratory investigation shows that each of these parameters is a function of the diameter of the borehole and the product of the volume rate of flow and velocity through the nozzles (QVn). Increasing QV, or decreasing the diameter of the borehole increases each parameter. These functions provide means of predicting the magnitude of each parameter and of scaling the cleaning forces. INTRODUCTION In drilling operations using conventional jet-type rock bits, the impinging jels create an important flow mechanism. Called crossflow, this flow mechanism originates in the impact area of the jets, spreads across the bottom of the hole and supplies the principal source of energy to clean the teeth of the bit and most of the bottom.' Besides providing the means of cleaning cuttings from the bit and the hole bottom, crossflow may also have other, less direct, effects on the rate of penetration. The shear stress generated on the bottom by crossflow will inIluence the thickness and permeability of any filter cake of mud solids or crushed material which forms on the bottom.' These factors may affect the rate of penetration. A previous pulblication introduced some fundamental concepts of crossflow.' Crossllow was shown to occur in a thin layer adjacent to the bottom, and to cover the bottom completely. The maximum velocity in the crossflow above any position on the bottom was found to be directly proporlional to the square root of the product of the volume rate of flow and velocity through the nozzles—the jct QV,,—and inversely proportional to the diameter of the borehole. This information indicated that the effectiveness of crossllow in scavenging the bottom can be improved by maximizing the jet QV. The investigation reported herein amplifies the definition of crossflow. Complete velocity profile data above a representative position on the bottom are analyzed. These data better illustrate control of the capacity of crossflow to scavenge the bottom, and also relate shear stress on the bottom to known, controllable parameters. The conclusion reached in the previous publication that maximization of the jet QV. produces the maximunl cleaning beneath current jet bits is unchanged by these new data; rather, it is strcngthened. Data presented here show that the kinetic energy flux above a representative position on the bottom is maximized by maximizing the jet QV. The shear stress on the bottom will also be shown to be maximized in the same manner. Since the functions relating the jet QV. to velocity, shear stress and kinetic energy also involve the diameter of the borehole, means of equating, or scaling, these quantities in different sizes of boreholes will be illustrated. EXPERIMENTAL EQUIPMENT AND TECHNIQUE JET BIT MODEL Data were recorded from the same laboratory model as used in the aforementioned investigation of the flow around a jet bit.' The model consisted of a 43/4-in. three-cone, jet-type rock bit in a smooth, flat-bottomed borehole constructed of lucite. The bit had a shape and nozzle placement closely resembling larger three-cone jet bits commonly used in field operations. Fig. 1 illustrates the impact area on the bottom of a jet from this bit. Details of the orientation of the jets may be found in the previous publication. TECHNIOU'E OF MEASUREMENT Measurements of the crossflow were made by inserting a very small Pitot tube through the bottom of the simulatetl boreholc. Extreme thinness of the layer of crossflow necessitated accurate measurements of the height of the Pitot tube above the bottom to achieve close definition of the velocity profile. A cathetometer, which could be read to the nearest 0.005 cm, was used to make this measurement.

Jan 1, 1966

By Leonard H. Goldman, Harold E. Marr

The PGT uranium assay probe is a borehole tool developed by Princeton Gamma-Tech over the last several years. It has the ability to do an in-situ assay of uranium in the presence of any amount of disequilibrium. It has some advantages over coring including cost, speed of analysis, and accuracy. In this paper we would like to give a brief description of the measurement and then show some sample logs from South Texas. Uranium exploration and development is carried out primarily by gamma logging since uranium daughters are prolific emitters of gamma rays. The conventional gross gamma tool for uranium logging is limited in value because of the inability of this tool to distinguish uranium from its daughters and other naturally occurring radioisotopes, such as potassium and thorium. This problem becomes severe in cases of disequilibrium. Disequilibrium, in a geological context, is defined as the condition when the gamma radiations from the daughter products are being emitted in a location different from that of the parent uranium. In the decay chain of uranium almost all the gamma radiation emitted in the entire chain comes from the daughter product, bismuth-214. Bismuth-214 is separated from uranium by several long-lived isotopes that are chemically active and have different physical properties, often resulting in shifts in the location of bismuth- 214 relative to the parent uranium. In the United States orebodies exhibiting disequilibrium are a common occurrence and the use of a gross gamma log to delineate uranium orebodies can lead to errors. At present the solution to the disequilibrium problem is extensive coring followed by chemical analyses of the cores. There are several drawbacks in using this technique. First is the high cost of coring, the second is the fact that no results are available for days, or typically, weeks after the drilling is done. Thus for development work, coring and drilling must be done on a grid basis and many additional holes are cored to ensure that the entire orebody is mapped. Another disadvantage to cores is the fact that a small volume is sampled, the volume of the core itself. This leads to problems in the mapping out of the orebody when the ore de- posit is not very homogeneous. The PGT probe described in this paper is a new solution to the disequilibrium problem. Basically, the probe measures radiations that come almost directly from uranium itself. The first daughter of uranium, which is protactinium-234 (Pa-234), is only separated from uranium by a 24-day half-life and no disequilibrium problems build up in such a short time. The PGT probe measures the intensity of a one MeV gamma line emitted by Pa-234 and, using this information, calculates the concentration of uranium. The PGT probe is 24" in diameter and 12 feet long. The probe contains a microprocessor which passes the information to a larger minicomputer in the truck. All data is analyzed on site, and the results from a high speed printer are presented to the geologist. Data is also available on 9- track IBM compatible tape for further processing. The PGT probe output is linear with uranium concentration. The only correction factor is for borehole size, and that only becomes important in boreholes bigger than seven inches in diameter. Dead time is compensated in the probe itself and no problems have been encountered in ore zones up to several percent UjO8. In addition to the uranium assay, a conventional gross gamma log is plotted alongside. Grade thicknesses for zones above cutoff are calculated as well as disequilibrium factors. COMPARISONS During its commercial operation PGT logged a series of 18 holes that had been cored and assayed. All of the holes in this series were logged in normal operation by regular field operators. The time to log each hole was generally under an hour, and in typical operation a PGT logging truck will do between 7 and 8 holes a day. The results of the comparison of the PGT and the core assays are presented in a series of figures showing plots of the PGT assay, core analysis and gross gamma measurements. The first three figures show individual holes with the gross gamma plotted along with the core and the PGT assays. All three logs were from holes on the reduced side of a rollfront deposit in South Texas. In Figure 1 we see the two wings of the roll- front at 143 ft and 150 ft separated by a barren zone. The wings are well defined both by the PGT assay and the core. There is approximately a one foot shift which can be attributed to drilling errors. The gross gamma is showing a rather severe discrepancy, being considerably lower and not showing the barren zone. The grade thickness calcula-

Jan 1, 1980