Search Documents

John Birkinbine, Philadelphia, Pa.: Mr. Sperry's paper is certainly a valuable addition to the literature upon alloys with iron, supplementing the data already published concerning the influence of manganese, chromium, tungsten, titanium, aluminium, etc.; and it is to be hoped that the presentation of information upon the influences of nickel may bring out comparisons with other alloys. Taking into consideration the properties of nickel, and its use as an alloy in heavy forgings, as set forth in the paper, there would appear to be no serious difficulties in utilizing this alloy by extending its application to pieces of more moderate size. The melting-temperature of nickel, as stated by Mr. Sperry, is considerably lower than those given by various authorities. Its point of fusion being so near that of iron, and its density but little greater, the difficulty of alloying it in the foundry should not be serious, particularly if it is applied as a ferro-nickel. The addition of nickel monoxide (NiO) to molten steel would appear to be less desirable than the application of metallic, nickel or of ferro-nickel, if such is produced on a commercial scale and at a satisfactory price.

Jan 1, 1896

By W. H. HOWARD

Discussion of the paper of W. H. HOWARD, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 92, August, 1914, pp. 2029 to 2046. EDGAR M. DUNN, Anaconda, Mont.-Mr. Howard's contribution to the literature on the Cottrell, method. of electrostatic precipitation of flue dust and fume at Garfield has been read by us with peculiar interest for the reason that we have been experimenting with the same process at Anaconda for the past eight or nine months, with a view to adapting it, under the direction of Dr. Cottrell and the supervision of J. 0. Elton. and D. R. Kellogg, representing the Anaconda Smelter Commission, to the treatment of very large volumes of gases, using large pipe treaters and various forms of electrodes, with about 150,000 volts rectified current. For the amount of gas to be treated here the 5-in. pipe means a cost for installation that is practically prohibitive, clue to the tremendous number of pipes required, and we have been trying to cut installation costs by increasing the size of the pipes. All of our work is still in the experimental stage, but we have obtained good clearance on our mixed roaster and converter gases with a 3-ft. pipe treater 20 ft. long, and with 5 ft. velocity therein; and with a discharge electrode of a single No. 29 nichrome wire set in the middle of the 3-ft. pipe, with. a consequent electrode spacing of 18 in. The current used has been 150,000 to -160,000 volts, .and of course there have been troubles galore, relating particularly to insulation and rectifying. Blast-furnace gases did not give so good clearance, probably due to relative poverty in moisture and S03 content of blast gases to roaster-converter gases; making the blast gases the poorer in conductivity. Our experience has been so satisfactory that in our next experimental plant-built on a somewhat larger scale-we shall attempt a 4-ft. treater with greater electrode spacing, and a somewhat higher voltage-up to 220,000. As to fractional precipitation, mentioned by Mr. Howard, this idea was tried out at Anaconda last year (1913). Formerly our furnaces (Bruntons) roasting flue dust for the recovery of white arsenic, passed so great an, amount of dust to the settling kitchens that refining of this arsenical product was necessary to eliminate the 5 to 20 per cent. dust contained therein. Consequently the manufacture of As203 was effected in two stages, with a reverberatory roast of the first .product to obtain the final 99.5 per cent. As203. -

Jan 11, 1914

By William Loblowitz

A simplified system of flotation testing has been developed recently at the Bureau of Mineral Research of Rutgers University. The technique involves the known principle of skin flotation and can be used with minute quantities of sample and reagents in a beaker. A vessel containing the conditioned sample with added water and flotation reagents is held inclined and rotated slowly. Water-repellent particles come in contact with air and float on the surface of the liquid, while wettable particles are submerged. The float is poured off and filtered whereas the nonfloat remains in the beaker. The filtrate may be returned to repeat the process. This procedure can be made quantitative. Separations are obtained and are remarkably complete and repeatable. The effect of different reagents, optimum quantities, pH and other variables can be determined in a fraction of the time required for conventional testing. However, the method gives no information on the effect of frothers and the quality of froth to be expected in a cell, and it is not practical for particles finer than 200-mesh. Unlike other preliminary tests, separate float and nonfloat products are obtained, and their contents can be determined quantitatively by chemical analysis or grain counts. After the optimum reagent combination has been determined, the effect of fines and frothing may be verified in the conventional flotation cell. On the other hand, agglomeration-tabling can be directly duplicated from beaker tests. Procedure: Five to ten grams of sample are weighed into a 100-ml beaker. Flotation reagents and a small initial quantity of water are stirred together; additional water is then added to produce the proper water-solids ratio. The beaker is then tilted to 45" and rotated slowly. After three to five rotations, liquid and float are poured off and filtered; the filtrate may be recycled until the separation is completed. One test generally requires less than 10 min. Reagent concentration and pH remain quite constant because of the recycling of the filtrate. Two to four tests may be made simultaneously, and the effect of varied conditions may be observed by comparison. Considerable time is saved in preparation and handling since small quantities of sample suffice for a series of systematic tests. Repeatability One test was repeated four times under constant conditions. The sample used was a quartz sand containing approximately 24 pct feldspar and some clay aggregates. The +28-mesh grains had been screened out, and most of those finer than 100-mesh had been removed by hydraulic classification. The results are presented in Table I. For comparison, 500 g of the sample were separated by agglomeration-tabling using the same reagent combination and quantities as given in Table I. The weight percent float was 18.3 pct, composed almost entirely of feldspar and with only traces of quartz. Most of the remaining feldspar was recovered in a middling product with 2.2 pct by weight.

Jan 1, 1952

By F. V. Lenel, G. S. Ansell

The creep behavior of an aluminum -aluminum oxide alloy, A T 400, fabricated by compacting an atomized aluminum powder, extruding the compact, cold working, and recrystallizing the extrusion, was investigated. This alloy has a dispersion spacing of 1 . Previously Ansell and Weertman determined the steady-state creep rate of a recrystallized aluminum-aluminum oxide SAP-type alloy, MD 2100, with a 0.48-p dispersion. This alloy was found to have a steady-state creep rate of less than 10-6 min-1, too small to be measured accurately. By employing a more sensitive method of measuring creep rate, it was possible to determine the steady-state creep rate of AT 400 alloy, which is somewhat faster than that of MD 2100, at a series of temperature and applied stresses. Above a stress of Burger's vector, A = dispersion spacing, u = is a shear modulus) the rate follms an equation of the type: Steady-state creep rate K = A exp. where A is a constant, Q is the activation energy for sey-diffusion, and is the applied stress. At stresses lower than the steady-state creep rate drops off sharply and is no longer in agreement with this equation. This behavior is in good agreement with that predicted by the model for dispersion strengthened alloys in the stress and temperature range investigated. The absolute value of the creep rate is, however, four orders of magnitude lower than that predicted if the normal number of active dislocation sources are assumed to be present. It is concluded that in this SAP-type alloy the usual three-dimensional dislocation network is not present. Instead, short dislocation segments extending from one dispersed particle and terminating at a neighboring particle may act as dislocation sources. With this provision the creep model proposed by Ansell and Weertman reasonably accounts for the creep behavior which was observed. RECENTLY, Ansell and Weertman1 proposed a dislocation model from which they derived creep equations to describe the steady-state creep behavior of dispersion - strengthened alloys. Following Schoeck,2 they assumed that the rate controlling process for steady-state creep is the climb of dislocations over the dispersed particles. In order to verify their creep model, Ansell and Weertman determined the steady-state creep behavior of an aluminum-aluminum oxide SAP-type alloy, MD-2100, in both the fine-grained as-extruded, and coarse-grained recrystallized conditions. Since the grain size was the order of the dispersion-spacing, their model was not applicable for the as-ex- truded alloy. It should, however, be applicable to the coarse-grained recrystallized alloy. The results they obtained were rather unexpected. No meas-ureable steady-state creep was observed for the recrystallized MD-2100 alloy. If their model is correct, and if the second-phase particles act solely to hinder dislocation motion, then some measureable steady-state creep would have been expected. On this basis, they postulated that, in this SAP-type alloy, the main effect of the fine dispersion was to inactivate dislocation sources rather than to hinder the movement of dislocations. In order to understand more fully this unusual creep behavior, and to determine the validity of the model proposed,' the steady-state creep behavior of an aluminum-aluminum oxide recrystallized SAP-type alloy, with a somewhat coarser dispersion spacing, was investigated. The results of this study are presented in this paper.

Jan 1, 1962

By A. T. Miesch

The purpose of this paper is to explore relations between the distribution and composition of uranium deposits on the Colorado Plateau and mineralogic, chemical, and lithologic aspects of their host rocks. The paper also appraises the host-rock sandstones as possible sources of elements in the uranium deposits. Other possible sources of elements are not discussed. Uranium deposits on the Colorado Plateau consist largely of sandstone and small amounts of mud-stone impregnated with uranium and vanadium miner- als and a suite of minor accessory minerals containing copper, lead, zinc, silver, iron, cobalt, nickel, yttrium, molybdenum, selenium, and arsenic, in addition to other elements locally. The deposits consist of clusters of closely spaced ore bodies which commonly aggregate several thousand tons, but range in size from less than one ton to several million tons. With only rare exception, the deposits show no close relation to fractures. The ore bodies are generally tabular in layers nearly parallel to the bedding in the host rocks, or they cross bedding at large angles to form roll structures. Absence of fracture control necessitates that the ore and associated elements were transported to the deposits by way of interstitial pore spaces in the sandstones. This points to the general process of lateral secretion as a possible mechanism of ore formation, and suggests the host-rock sandstones as a possible source of the metals. Roll structures in the ore

Jan 1, 1962

By H. W. Kerr, B. Soutiere

THE possibility of using unidirectionally solidified eutectic alloys as high-strength composite materials has been investigated by several workers. Unidirectionally solidified lamellar and fibrous eutectics have been shown to have good short-time structural stability at temperatures close to the eutectic melting temperature.'-4 Several investigations of both short-time high temperature tensile properties and creep properties of eutectic alloys have been carried out,3-" with promising results. Little work has been reported, however, on the thermal stability of eutectic alloys which have been unidirectionally solidified and subsequently deformed in compression. Since processes such as rolling and grinding introduce compressive stresses, and since the properties depend on the spacing and perfection of the composite structure10,11 this aspect is of definite importance if unidirectionally solidified eutectic alloys are to be considered for commercial use. A Cd-Zn alloy made from 99.999 pct starting materials was cast into a graphite boat and zone levelled12 to obtain a completely lamellar structure at one end of the bar. Sections from this region of the bar were removed, recast into 6.5 mm I.D. Pyrex tubing, and solidified unidirectionally upwards at a rate of 2.8 cm per hr. Specimens were cut from the solidified rods, heated in air at 200°C (0.88 of the eutectic melting temperature) for various lengths of time, and examined metal-lographically. Compression specimens were also cut from the solidified rod carefully machined to a length of & in., and deformed with the compressive axis parallel to the original growth axis to produce a total longitudinal strain of 12 pct. Some of these specimens were examined metallographically; others were heated in air at 200°C for various lengths of time and then examined. Metallographic examination of the deformed specimens showed the two types of deformation previously described; slip lines13 (smoothly bent lamellae) and kinks13,14 (sharply bent lamellae). Very close to the specimen ends there were a large number of deformation bands, but at a distance of about -re- in. the deformation was very localized, as shown in Fig. 1.

Jan 1, 1970

By Martin Coryell, Eckley Coxe, R. P. Rothwell

WILKES-BARRE, PA., April, 1871. THE great development of the mines and metallurgical works of this country during the last few years, accompanied as it has been by the investment of enor¬mous sums of money in purchasing lands, and in the erection of improvements, requires that advantage should be taken of the accumulated knowledge of engi¬neers, superintendents, and others, in mastering the problems which are con¬stantly presenting themselves for our action. Among those may be mentioned the consideration of more economical systems of mining in our coal and metal¬liferous mines, improved methods of transportation above and below ground, unwatering and ventilating mines, the mechanical preparation of coal and other minerals, the various metallurgical processes, and, in fact, every question tending to the attainment of two great objects 1st. The more economical production of the useful minerals and metals. 2d. The greater safety and welfare of those employed in these industries. In European countries, where the arts of mining and metallurgy have long been the subject of the most careful study, no means have been found so effectual in attaining the end above proposed as the free interchange of experience among those actually engaged in these industries, and this object has been accomplished, mainly, through the medium of institutes, associations or societies, composed of those engaged in these occupations, and by the- periodical publication of essays or papers, communicated to such societies by their members. It must be evident to all practical men that the interchange of the varied experience of those engaged in such occupations in this country could not fail to advance very materially the desired objects; it is, therefore, proposed to establish an American Institute of Mining Engineers, which will hold its meetings periodically in the great mining and metallurgical centres, where works of interest, such as mines, machine shops, furnaces, and other metallurgical works, can be inspected, and the members exchange their views, and consult for mutual advantage upon the difficulties encountered by each; these transactions or proceedings, when published, would form a most valuable and greatly-needed addition to our professional literature. It is proposed that a meeting of those sympathizing with the object above men¬tioned shall be called for the purpose of organizing such an association, the place and time of meeting being Wilkes-Barre, Pa., and the month of April or May. Communications indicating the opinion and wishes of all, both as to these points, and also as to the organization and objects of the Institute, will be gladly received by any of the undersigned, and a notice of the date of meeting, which will be arranged to suit the greater number, will be duly communicated. Any

Jan 1, 1873

By Harold B. Treweek

The development of full scale flotation circuits based on laboratory and/or pilot plant data is discussed. Auxilliary operations, equipment and layout essential for trouble-free start-up and operation are noted. The selection of flotation cell size is discussed as it affects plant capital and operation costs.

Jan 1, 1978

By P. N. Ivanov

The world experience shows that the tremendous potentialities of the computers and other technical means in improving management efficiency are not fully utilized. One of the causes is the tendency to solve the problems of management automation divorced from the management methods and schemes which demand continuous improvement in view of the steady progress of the social production. It may be safely affirmed that making decisions on management improvement divorced from management schemes or on both divorced from management automation problems cannot lead to success. The grave and sometimes unsuperable difficulties encountered in management automation arise from copying traditional management methods and schemes without solving the problems which exist both in management and automation fields. The system solution of management problems has unquestionable advantages and is not proposed for discussion. What is proposed to discuss is the difficulties emerging in developing a methodology of the system approach to management improvement and automation. Though aware of the fact that the questions proposed for discussion are not new, we think it advisable to briefly review them, first because they fall in the "chronically unsolvable" category, and, secondly, as it will enable us to illustrate the method of solving them in the framework of the proposed system approach.

Jan 1, 1977

By A. A. Jr. Smith, J. S. Smart

The controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modern copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range o to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously. Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,'v2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of %-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 8jo°C. from a surface scale. Test wires wcre drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in., and a final cold reduction of 75 per cent to 0.081 in. Oxygen-bearing slugs made by remelting nere hot-rolled to 4ia in.. drawn to 0.162 in., annealed for 30 min. at 6o0°C. and cold-drawn 75 per cent to 0.081 inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 3i6-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700' to 8o0°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals wcre of one hour duration followed by a rapid quench in 10 per cent HZSO*. Effect of Phosphorus The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1946

By A. A. Jr. Smith, J. S. Smart

The controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modern copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range o to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously. Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,'v2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of %-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 8jo°C. from a surface scale. Test wires wcre drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in., and a final cold reduction of 75 per cent to 0.081 in. Oxygen-bearing slugs made by remelting nere hot-rolled to 4ia in.. drawn to 0.162 in., annealed for 30 min. at 6o0°C. and cold-drawn 75 per cent to 0.081 inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 3i6-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700' to 8o0°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals wcre of one hour duration followed by a rapid quench in 10 per cent HZSO*. Effect of Phosphorus The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1946

By A. N. Holden, J. H. Hollomon

A. H. COTTRELL* and A. T. * Dept. of Metallurgy, Birmingham Univ., England. CHURCHMAN*—We have been making some experiments recently very similar to those reported by Messrs. Holden and Holloman. Wires of Armco iron, 0.077 in. diam. were decarburized in wet hydrogen until the yield point was removed; they were then extended 31/4 pct and annealed at 880°C for 120 hr in dry hydrogen. This process produced large crystals which extended through the cross-section and were about 3/4 in. in length. Since the length of each crystal

Jan 1, 1950

By J. P. Witherow

Mr. BIRKINBINE's description of the bad working and sudden chilling of the Warwick Furnace last summer, seems to me quite phenomenal in blast-furnace practice. During my connection with the management of blast furnaces for many years, in the anthracite, cake, and raw-bituminous coal districts, such a me has never come under my notice. It seems to me that the scaffold in the zone of fusion could not have established itself (so that the whole power of the engines, with a blast pressure ranging from 12 to 18 pounds per square inch, could not penetrate), unless the furnace was previously badly scaffolded and bridged in some of its upper sections, from 15 to 30 feet above the hearth level, either in the zone of chemical action or the beginning of the zone of fusion. Such a 'barrier to the upward gaseous currents would cause a suspension of combustion which may have superinduced the scaffold that is assumed to have existed in the zone of fusion. It is difficult to conceive that an agglomerated mass almost across the section of the lower bosh should have formed all at once, if the furnace was free and porous for the reaction of the gaseous currents, above. Therefore, I think, the Warwick furnace was by no means in as free, open, and fine internal condition at the time the trouble commenced as the description of its regular working would lead us to suppose. I do not question the accuracy of the statements relative to the output of iron, etc I merely claim that the phenomenta, as described, could not have been almost instantaneously developed, unless there had been an incipient scaffold and lodgment above the zone of fusion. I would state my hypothesis to be that the stock lodged or collected in some of its upper sections during fie process of blowing-in, on which, as a basis, more or less accumulations may .have lodged, and thus, indirectly, caused the formation of the suc-

Jan 1, 1881

By Paul Bechtner

THE name bentonite formerly was applied solely to a peculiar clay occurring in Wyoming and South Dakota, which was distinguished from other clays by its unctuous feel when wet and the property of swelling in water. In the last decade scientific studies of clay have recognized that bentonite is composed mainly of the clay mineral montmorillonite and the name bentonite has been extended to cover the entire family of clays that have montmorillonite as their chief constituent. Montmorillonite has the chemical formula of A1203-4Si0-xH2O, With Fe203 and MgO replacing part of the A1203. The montmorillonite crystal is an Si-Al-Si clay mineral, being formed of two silicon-oxygen sheets with an aluminum-oxygen sheet sandwiched between them. In contrast, kaolinite-the chief clay mineral of most clays other than bentonite-is Si-Al, one silica and one alumina sheet. The unit crystal of montmorillonite is much thinner than that of kaolinite, with greater surface area. These differences in crystal structure patterns are leading factors in the dissimilar properties and commercial uses of bentonite compared with other clays. Mineralogically, bentonites are 85 to 90 pct montmorillonite with fragments of feldspar, gypsum, calcium carbonate, quartz and traces of other minerals. They vary in color; the widely used Wyoming type is creamy white when dry and a light shade of tan when wet; the low-swelling bentonites of the southern United States and elsewhere are found in many shades of gray, blue, yellow, red, and brown. Pure white bentonites are rarer and generally of the medium or low-swelling type, though there are a few exceptions to that general rule. PROPERTIES Bentonites may be divided into two general classes: (1) those that adsorb large quantities of water, "swelling" greatly in the process, and that remain in suspension in thin water dispersions; (2) those that adsorb only slightly more water than ordinary plastic clays or fuller's earths, do not swell noticeably, and settle rapidly in thin water dispersions. Another distinction is that some varieties of the No. 2 type

Jan 1, 1949

By C. E. Van Orstrand

AN intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it will be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. H. Emmons,1 minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. MATHEMATICAL THEORY In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be assumed that the intrusive is a large parallelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, t = o), which has the same thermal properties as the intrusive, is2,3 [ ] In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. 'v = temperature at point x, y, z, time t. vo = initial temperature throughout the intrusive, t = o. K = coefficient of thermal diffusivity. a, ß, ? are variables of integration. Put n = m in Eq. I, and we have [ ]

Jan 1, 1944

By John Henderson

Densities of melts 0f the lime-iron oxide-silica system in contact with solid iron have been measured by the maximum bubble pressure method in the temperature range 1250° to 1440°C and the composition range 0 to 40 mol pct lime, 15 to 100 mol pct iron oxide, and 0 to 55 mol pct silica. Densities range from 4.65 g cm 3 for wustite at 1440°C to 2.75 g cm-&apos; at 1350°C for a melt containing 30 mol pct lime, 20 mol pct iron oxide, and 50 mol pct silica. The results are interpreted in terms of a postulate that the melts can be regarded as a random array of oxygen ions in which regions of local order exist to satisfy the coordination requirements 0.f the cations. An understanding of the nature of metallurgical slags is basic to the development of a sound theoretical description of heavy metallurgical extractive and refining processes. Because these liquids are complex, direct measurements of their properties has not thrown much light on their structure. This has led to the approach of measuring the properties of simpler liquids, and building up their complexity until slag compositions are reached. In this way the density of liquid iron silicates was measured in a previous study1 and the present work represents a further stage in this synthesis. EXPERIMENTAL The technique used in the measurement of density was the maximum bubble pressure method. Details of the apparatus and procedure were similar to those previously reported,&apos; with the exception that a constant voltage transformer was used to supply the power input to the furnace and six silicon carbide resistance elements were used in place of the molybdenum winding. With these modifications melt temperature could be maintained within 1 centigrade degree during the course of a run. The silica used to prepare the melts was washed natural quartz ignited at 1000°C; wustite was prepared by air-melting A.R. grade ferric oxide in an iron crucible and lime was prepared by air ignition, at 1000°C, of weighed quantities of A.R. grade calcium carbonate, previously air-dried at 110°C. The finely ground constituents were intimately mixed in a glass ball mill prior to melting. Temperatures quoted are accurate to * 5°C and the standard deviation of the density values, calculated by the method of least squares, ranged from 0.5 to 1.8 pet. However, replicate determinations of density on different melts of the same nominal composition at the same nominal temperature did not vary by more than 1 pct, Table I, and this figure has been taken as an estimate of the accuracy of the density results. The density of carbon tetra-chloride was also measured as a check on the absolute performance of the experimental method. At 20°C a value of 1.593 * 0.002 g cm"3 was obtained; this compares with the literature value2 of 1.595 g cm"3. Results of experiments designed to measure the dependence of the density of lime-iron oxide-silica melts, in contact with solid iron, on composition and temperature are shown in Table I. Because iron sometimes precipitated in the sample during quenching, the Fe203 chemical analyses were only poorly reproducible and should be taken as a guide rather than as absolute values. Fig. 1 shows the data from various sources for the density of liquid iron silicates and Fig. 2 shows isodensity contours at 1410°C for lime-iron oxide-silica melts, calculated by graphical interpolation of smoothed curves drawn through the experimental results, together with the 1400°C results of Adachi and ogino3 and Pope1 and Esin.4 Fig. 3 shows the isothermal variation with composition of the volume of melt per gram ion of oxygen at 1410°C and Fig. 4 shows regions in which the temperature coefficient of this volume is negative, positive, or negligible (<0.005 cm3 deg-I). DISCUSSION a) Disparity Between Reported Density Results. Consider the system iron oxide-silica, the results for which are summarized in Fig. 1. Although there is some difference in the temperatures at which the various densities apply, this difference is not sufficiently large to account for the observed discrepancies. The reliability of the present results for the low-silica region has been confirmed by measurement of the density of liquid wustite by three different techniques. At 1410°C the density measured by a balanced-column method was 4.55 g cm"3, by a combination balanced-column and gas-densitometer method 4.59 g emd3, and by a pycnometer method 4.53 g cm"3. Schenck, Frohberg, and Hoffermann&apos; have also reported a value of 4.55 g cm"3 for the density of liquid wustite at 1400°C. It must be concluded, therefore, that neither Pope1

Jan 1, 1964

By Henry Siegmann

HISTORY OF PRODUCTION AND USE In 1899 the consumption of fluorspar in the United States was reported as 16,000 tons. The invention of the open-hearth method of steel manufacture, plus the beginnings of a fluorine chemical industry, pushed consumption of fluorspar to 250,000 tons by 1918. In contrast to these consumption statistics of the past, the most recent statistics available (1972) indicate a total fluorspar usage in the United States of 1.352 million st (Table 15.4D.1). Fluorspar remains the world&apos;s cheapest source of fluorine, and its unique properties make the mineral the most desirable fluxing agent for steel refining. The linking of fluorine with carbon in the late 1930s resulted in the production of fluorocarbon, and constant growth in production over the years has formed the backbone of a strong fluorine chemical industry. For example, in 1972 it is estimated that total fluorocarbon production amounted to 2.113 million tons, and that, in this process, over 1.351 million tons of acid-grade fluorspar was consumed. The producers of primary aluminum long have been concerned about the fast dwindling reserves of natural cryolite. They found the solution to their problem by utilizing fluorspar for the manufacture of synthetic cryolite and aluminum fluoride. Nuclear weapons, as well as the growing number of peaceful uses for atomic reactors, constitute a market for uranium hexafluoride. This chemical and chlorine pentafluoride, used as an oxidizer with rocket fuels, are products that are as much a novelty as fluorocarbons were 25 years ago. Judging from past success in the field of fluorine chemistry research, it is safe to assume that the market for these chemicals will grow in the future. Three major industries account for the bulk of the fluorspar consumption: steel refining, fluorine chemical, and primary aluminum production. These industries have had a pattern of fabulous growth in the past, and their future plans point to a continuation of this pattern. It seems logical that the fluorspar usage also should continue its upward trend. Considering the growth of the fluorspar industry since 1899, and the obvious dependence on imports of fluorspar as a raw material, one of the most puzzling aspects of the past has been the apparent lack of coordination between fluorspar production and fluorspar consumption. A few authoritative voices have spoken out concerning the need to expand fluorspar production in order to meet consumption of the future. During World War II, the U.S. Government took positive steps in this direction by authorizing purchases at attractive prices for its "stockpile program." As a consequence, new fluorspar producing facilities were built, not only in

Jan 1, 1976

By L. W. McKeehan

The occurrence of twins in large ferrite crystals, made by a new process, was reported in a recent note.&apos; This paper describes a typical case of such twinning and suggests, on the basis of the observed facts, why smooth slip-planes are rarely observed in this metal. Method of Preparation The material in which the crystals here dealt with were grown was made from 1/8in. Armco iron welding rod containing C, 0.04; S, 0.037; P, 0.003; Si, 0.008, and Mn, 0.02 per cent. This rod was cold drawn into wire about 1 mm. dia. A piece of this wire was supported vertically and was locally heated in hydrogen at atmospheric pressure to about 1400" C. by an alternating current (60 cycles per sec.) of about 35 amp., passed through it between a pair of traveling contacts about 8 cm. apart. The rate of travel for the case in hand was 12 cm. per hr. After some 30 cm. of the length of the wire had been heated and cooled in this manner the whole wire was immersed for a few seconds in dilute nitric acid, not restrained by alcohol. Etching was continued until, as nearly as could be judged by eye, the original smooth cylindrical surface of the wire was no longer capable of specular reflection. Measurements The wire in the etched state was next mounted in a goniometer of special form which allowed the measurement of the spherical coordinates of the normals to any plane surfaces left by the etching. These coordinates were most conveniently a polar distance, 8, from one direction of the wire axis, and an azimuth or longitude, ?, from an arbitrary prime meridian. The region to be described more particularly is shown at a low magnification in Fig. 1, which gives two different views, differently illuminated to show the spatial relationship of a crystal occupying most of the part shown and of an inclusion, or rather a series of three inclusions suspected of being twins based on the principal crystal.

By J. M. Roberts, N. Brown

The stress-strain behavior of zinc single crystals was measured over a strain range of 10-6 to 10-2. The phenomenon of macroyielding was observed in detail and plastic strains were detected at almost zero-stress. Closed hysteresis loops were observed during loading and unloading in the strain region of about 10-5. From the hysteresis a frictional stress on the dislocation of about 6 psi was obtained. A preliminary analysis indicates that impurities are primarily responsible for the friction. Nonelastic Strains as much as 10 -4 were recovered depending on the amount of prior deformation. Part of the recovered strain occurs instantaneously upon unloading and the remainder occurs at zero stress. The time dependence of the recovered strain was measured. THIS investigation is concerned with the details of plastic deformation preceding the ordinary yield point as measured with the usual strain sensitivity of about 10-4. The approach leads to internal friction observations in the hitherto neglected frequency range below 10-1 cycles per sec. It is believed that if the phenomenon of macroscopic yielding is to be understood, then the stress-strain curve in the neighborhood of the macroyield point should be greatly magnified. It may then be possible to determine whether macroscopic yielding is a unique event or whether it is a process which begins gradually at a lower stress. In the case of low-carbon steel a unique event obviously occurs at the macroscopic yield point as indicated by a drop in the load, but copper appears to exhibit a gradual transition from the elastic to the plastic state. In zinc the yield point is rather abrupt although the data indicates that some plastic deformation precedes large scale yielding.&apos; One of the purposes of this investigation is to determine whether there is an abrupt transition from the preyield microstrain region to the region of macroscopic deformation. Such a rapid transition would support the concept that there is a critical stress for yielding. The concept that yielding is a unique event associated with such phenomenon as activating a Frank-Read source, freeing the dislocation from solute atoms, dislocations cutting through dislocations, or dislocations moving freely by one another, has been expounded widely on theoretical grounds. It is hoped that highly sensitive measurements of strain in the neighborhood of the macroscopic yield point will shed some light on the event known as the "Yield Point". EXPERIMENTAL METHOD 1) Specimens—High-purity zinc was cast into spherical graphite moulds in air and grown into spherical single crystals by the Bridgman method under a positive pressure of Argon gas. Spectro-graphic analysis of cleaved sections from four crystals showed a purity of 99.994 pet Zn. The specimens were acid machined with an 1/8 in. gage section in a form similar to those used by Parker and co-workers.2 Bausch type grips were fastened to the specimen by Epon VI adhesive. The specimens were oriented so that only [1120] (0001) slip occurred. Fig. 1 shows two of the specimens in the grips. Prior to each test, the gage section of the specimen was given a concentrated HNO3 chemical polish followed by alcohol rinsing and air blast drying. 2) Test Method- The shear tests were performed on an Instron testing machine and the experimental set-up was made very "hard". Strain could be measured to a sensitivity of 10 -6 by means of a capacitance gage extensometer. The design and calibration of this type of extensometer to measure microstrain, as applied to pure shear and tensile tests of metals, will be the subject of a separate paper—therefore, only a brief account will be presented here. The method essentially consists of attaching a

Jan 1, 1961

By Harlan W. Nelson, James B. Purdy

A study of data obtained during laboratory tests to determine the suitability of bituminous coals for use in residential underfeed stokers of the clinkering type has led to the following general conclusions: 1. Performance data obtained during the test furnish useful and practical information upon which to judge the performance of stoker coals. 2. Conclusions derived from the results of evaluation tests are in general agreement with use experience of the coals in the field. The method is of practical use in this regard. 3. Few direct relationships were found between data furnished by the evaluation test and determinations by standard laboratory tests. This is particularly true with regard to coke formation and clinker formation, two of the most important factors in determining the degree of satisfaction to be obtained in applications of the small underfeed stoker. It has not been the intention in this paper to prescribe this evaluation test as the best method for the evaluation of coals for use in residential stokers. That there are other test methods having similar objectives serves to point out the necessity for full-scale laboratory tests. At the present time, a standard test procedure for the evaluation of coals for use in residential stokers is not available. For the past several years a joint committee, appointed from the membership of the Residential Stoker Committee of Bitulninous Coal Research, Inc., and from the Engineer- ing and Research Committee of The Stoker Manufacturers Association, has been working to develop a standard procedure for testing and evaluating bituminous stoker coals. This procedure has been completed to the extent that it has been drawn up in tentative form. It is now planned to install the equipment in several laboratories and to run check tests, using portions of identical lots of coal, to determine the degree of reproducibility offered by the method. Completion of this standard test procedure should greatly facilitate the evaluation of coals for use in residential stokers. Acknowledgments The cooperation of coal operators sponsoring the coal evaluation tests, in granting permission to use data and results from their tests, is gratefully acknowledged. Acknowledgment is also made to Carroll F. Hardy, Chief Engineer, Appalachian Coals, Inc., for his interest and timely suggestions on the preparation of this paper. Special thanks are due to Ralph Sherman, Assistant Director, Battelle Memorial Institute, who was largely responsible for development of the evaluation procedure, for helpful suggestions and advice. References I. H. A. Sherman: The Evaluation of Coal for Use in Domestic Stokers. Univ. of Ill., Eng. Experiment Station, Circular No. 39 (1939). 2. . Q. Shotts: The Relation of Free- swelling Indexes to Other Characteristics of Some Alabama Domestic Stoker Coals. TP 2314, Coal Tech., (Feb. 1948); Trans. AIME (1948) 177, 502. 3. . J. Helfinstine and C. C. Boley: Correlation of Domestic Stoker Combustion with Laboratory Tests and Types of Fuels 11. Combustion Tests and Preparation Studies of Representative Illinois Coals. Ill. State Geol. Survey, Re1. of Zntlestigations No. 120 (19467 ) p. 35. DISCUSSION E. R. Kaiser*—AS a former fuel engineer assigned to residential stokers at Battelle, the writer has read with considerable interest the paper by Messrs. I&apos;urdy and Nelson. It is gratifying to note that earlier test techniques have been developed and that criteria found important in the years 1935 to 1938 are still important in judging the performance of stoker coals for residential heating. The authors have plotted a number of the primary coal data singly against performance data of the stoker in an effort to establish relationships. Unfortunately, wide scattering of points usually resulted, which did not illustrate what experience generally indicates to be the case. For example, Fig 3 indicates almost no trend in the percentage of released ash converted to clinker with change in ash-softening temperature. Other factors, such as fuel bed temperatures and zones of heat release must have influenced the results. In the present state of our knowledge, we cannot explain all of the reasons why suitable stoker coals perform satisfactorily, nor why one satisfactory coal may be better than another. It would therefore

Jan 1, 1950