Search Documents

By Alfred H. Hesse, Edwin T. Myskowski

The development by the U. S. Bureau of Mines of a process for purifying manganese by electrolysis has stimulated interest in manganese alloys. While recent publications have shown some alloys of manganese and copper to possess rather unusual properties, none have included information on tensile properties, which have an important bearing on the usefulness of the alloys. Manganese-copper alloys can be heat-treated, since the single phases that exist at high temperatures may be retained by quenching. According to Persson,1 when quenched alloys containing from about 30 to nearly IOO per cent manganese are reheated, alpha manganese is precipitated (Fig. I). Calculations based on Persson's X-ray data indicate that this decomposi-tion is accompanied by a change in volume of as much as ; per cent. The reason that this large volume change has not been noted probably is the slow rate at which equilibrium is reached by these alloys. In an investigation on hardening by cold-work and heat-treatment, Dean and Anderson3 found that quenched alloys increase in hardness with manganese content and that high-manganese alloys harden very slowly with cold-work, while high-copper alloys harden much more rapidly. Heat-treatment has little effect on manganese-copper alloys containing less than 40 per cent Mn, and affects those alloys containing more than 40 per cent in accordance with their manganese content and heat-treating temperature. Dean and Anderson4 also found that cold-work increased electrical resistance of alloys containing from 50 to 80 per cent Mn, and that heat-treatment of alloys containing from 40 to 96 per cent Mn altered the electrical resistance considerably. Dean, Anderson and Potter6 have shown that the high vibration damping capacity that characterizes manganese-copper alloys containing 40 to go per cent Mn is affected by cold-work and heat-treatments. Highest vibration damping capacity at low stresses was obtained by heating for 2 hr. at 450°C. (842°F.) after quenching from solution temperatures. Preparalion of Alloys.—The alloys for these tests were melted in a 17-lb. basic-lined high-frequency induction furnace using electrolytic manganese, grade A ingot copper and a 70-30 CU-Mn master alloy (69.80 per cent Cu, 0.12 Fe, 0.04 Si, 0.006 S, 0.07 C, balance Mn). The manganese was heated slowly to expel excess dissolved gases and melted before the addition of copper. No fluxes or covers were used. The melts were cast in tapered iron molds and the ingots were reduced go per cent when forged to 1/2-in. rounds. These rods were given 2-hr. solution treatments at temperatures that depended upon the composition (Table I). Tensile Tests.—The tensile specimens, 0.313-in. diameter (1.25-in. gauge length),

Jan 1, 1942

By Edwin T. Myskowski, Alfred H. Hesse

The development by the U. S. Bureau of Mines of a process for purifying manganese by electrolysis has stimulated interest in manganese alloys. While recent publications have shown some alloys of manganese and copper to possess rather unusual properties, none have included information on tensile properties, which have an important bearing on the usefulness of the alloys. Manganese-copper alloys can be heat-treated, since the single phases that exist at high temperatures may be retained by quenching. According to Persson,1 when quenched alloys containing from about 30 to nearly IOO per cent manganese are reheated, alpha manganese is precipitated (Fig. I). Calculations based on Persson's X-ray data indicate that this decomposi-tion is accompanied by a change in volume of as much as ; per cent. The reason that this large volume change has not been noted probably is the slow rate at which equilibrium is reached by these alloys. In an investigation on hardening by cold-work and heat-treatment, Dean and Anderson3 found that quenched alloys increase in hardness with manganese content and that high-manganese alloys harden very slowly with cold-work, while high-copper alloys harden much more rapidly. Heat-treatment has little effect on manganese-copper alloys containing less than 40 per cent Mn, and affects those alloys containing more than 40 per cent in accordance with their manganese content and heat-treating temperature. Dean and Anderson4 also found that cold-work increased electrical resistance of alloys containing from 50 to 80 per cent Mn, and that heat-treatment of alloys containing from 40 to 96 per cent Mn altered the electrical resistance considerably. Dean, Anderson and Potter6 have shown that the high vibration damping capacity that characterizes manganese-copper alloys containing 40 to go per cent Mn is affected by cold-work and heat-treatments. Highest vibration damping capacity at low stresses was obtained by heating for 2 hr. at 450°C. (842°F.) after quenching from solution temperatures. Preparalion of Alloys.—The alloys for these tests were melted in a 17-lb. basic-lined high-frequency induction furnace using electrolytic manganese, grade A ingot copper and a 70-30 CU-Mn master alloy (69.80 per cent Cu, 0.12 Fe, 0.04 Si, 0.006 S, 0.07 C, balance Mn). The manganese was heated slowly to expel excess dissolved gases and melted before the addition of copper. No fluxes or covers were used. The melts were cast in tapered iron molds and the ingots were reduced go per cent when forged to 1/2-in. rounds. These rods were given 2-hr. solution treatments at temperatures that depended upon the composition (Table I). Tensile Tests.—The tensile specimens, 0.313-in. diameter (1.25-in. gauge length),

Jan 1, 1942

Jan 1, 1938

By Alden B. Greninger, Alexander R. Troiano

Metallurgists have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies,30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel. I. The Martensite Transformation Previous Work Microstructure and Crystal Structure of Martensite.—Among the best series of published photomicrographs of quenched steels are those of Whitely,1 Robertson,2 Hanemann and Schrader,3 and Lucas.4 The crystal structure of martensite is body-centered tetragonal, with axial ratio varying from 1 near 0.0 per cent carbon to 1.08 for 1.75 per cent

Jan 1, 1940

By Alden B. Greninger, Alexander R. Troiano

Metallurgists have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies,30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel. I. The Martensite Transformation Previous Work Microstructure and Crystal Structure of Martensite.—Among the best series of published photomicrographs of quenched steels are those of Whitely,1 Robertson,2 Hanemann and Schrader,3 and Lucas.4 The crystal structure of martensite is body-centered tetragonal, with axial ratio varying from 1 near 0.0 per cent carbon to 1.08 for 1.75 per cent

Jan 1, 1940

By Alvin F. Kroll

BUNKER Hill & Sullivan Mining & Concentrating Co. has three major sources of ore at present: high grade square-set ore, low grade caving ore, and low grade reclaimed washed jig tailing. These three ores constitute the feed to the 3000-tpd concentrator that produces lead-silver, zinc, and pyrite concentrates. Each ore has different characteristics of grindability, mineral particle size, composition, and content, but all are amenable to the same mill circuit and reagents. The gangue is primarily quartzite. The Bunker Hill concentrator is now using a coarse primary grind followed by a regrind of sand fractions of lead rougher tailing, lead middling, and lead cleaner tailing, and further regrind of sand fractions of zinc middling and zinc cleaner tailing. This is done in order to recover all valuable minerals at the largest size possible. The tendency to overgrind the ore particles, which are more easily ground than the gangue particles, is thereby reduced-lessening their loss in the flotation tailings. The coarse primary grind and regrind method has the advantages of: providing more selective grinding, minimizing sliming, giving a cleaner lead-zinc separation, and reducing mill requirements for reagents and water. Improved lead-zinc separation raises overall recovery and also increases lead and zinc recovery in the respective concentrates by keeping middling particles out of concentrate and tailing.

Jan 6, 1954

By H. M. Howe, Levy A. G.

Four aspects of flow in the plastic deformation of steel by overstrain, such as punching, wire-drawing, tensile rupture, etc, are…

Jan 1, 1915

With this issue of the Bulletin, the Institute puts into operation a plan which it has long had under consideration for enlarging its field of usefulness to its members. We refer to the Index to periodical literature bearing on mining, metallurgy, and related subjects, which will be found in the advertising section at the end of the Bulletin. The Index is printed on alternate pages so that anyone who desires to compile a card index can readily clip the items and paste them onto cards. By its affiliation with the Engineering Societies Library, the Institute possesses unexcelled facilities for the preparation of this Index, since practically every important engineering or technical paper published anywhere in the world is regularly received by the library. The items for publication in the Index are first selected by the library staff, but their final approval and their order of arrangement remains in the hands of the editor. A word should be said in explanation of the system of classification that has been adopted. It will be noted that the classification is extremely broad, no attempt having been made to gather the references into closely specialized groups. Our reason for breaking away from the modern tendency toward minute specialization is based upon the fact that the fundamental principles underlying all engineering are not by any means so diversified as has commonly been supposed. For example, it is not at, all unlikely that an engineer engaged in large-scale ore mining in the Southwest can profit by observing the methods employed by his colleagues in the Pennsylvania coal mines. It is notorious also how extensively the brotherhood of chemical engineers has profited by the. earlier experiences of the ore-dressing and metallurgical engineers. If the Index were minutely sub-divided, it would always be possible that the coal-mining engineer, for example, might fail to observe a most important paper because it happened to be listed tinder the head of iron mining. For this reason, mining practice in general is consolidated under one head. The same line of reasoning applies to other divisions as well. In order to make the Index of practical value to all members of the Institute, wherever they may be situated, the library will undertake to supply, for a nominal charge, an abstract, a translation, a typewritten copy, a photostat copy, or the original of any article in the Index. Requests for service of this character should be addressed directly to the Engineering Societies Library, 29 West 39th St., New York. Members are urged to cooperate toward the success of this new departure by sending us suggestions. Although every effort has been made to anticipate the wishes of the members, it is almost impossible to foretell what services may be most useful to our 7000 constituents. Furthermore, it is known that some men prefer one method of classification while others would find another method more convenient.

Jan 9, 1918

By A. S. Yue

It was deemed desirable to obtain an understanding of the vacuum desulfurization process. McKechnie1 has reported that the sulfur content of nickel- and cobalt-base alloys is reduced in vacuo. Keverian and Taylor2 have observed that vacuum melting causes desulfurization of iron-carbon-silicon alloys. Garnyk and samarin3 have desulfurized transformer steel by vacuum treatment. Experiments were conducted in order to investigate the desulfurization of liquid iron under reduced pressures, and to establish the effect of some alloying elements, and various crucible materials. A vacuum-induction furnace of 50-lb capacity was used. The charge was Armco iron. Silicon was added as 90 pct ferrosilicon, carbon as electrode graphite, and aluminum as high-purity aluminum metal. Magnesia and silica crucibles were used, their inside diameters were 5 1/2 and 5 3/8 in., respectively. The temperature was measured with an optical pyrometer and it was held at 1600 1 15°C. Samples were withdrawn with quartz tubes of 6 mm ID, without disturbing the furnace atmosphere. Pressures were measured with an alphatron gage. The experimental results are shown in Fig. 1. They indicate that: 1) Sulfur can be removed from liquid iron alloys by vacuum treatment; 2) The desulfurization is enhanced by the presence of silicon, carbon, and aluminum, all these elements increase the activity of sulfur dissolved in liquid iron;4 3) The pronounced effect of silicon indicates that probably a volatile silicon sulfide is formed, Alcock and Richardson5 have observed a similar phenomenon; 4) The same rate of desulfurization was obtained when the metal was contained in either magnesia or silica crucibles. Dr. J. Keverian has contributed many discussions and recommendations. M. S. Sutliff has helped in conducting the heats. The permission of General Electric Co. for this publication is gratefully acknowledged.

Jan 1, 1960

By AIME AIME

A SPECIAL meeting arranged by the Petroleum and Gas Committee of the American Institute of Mining and Metallurgical Engineers was held on Tuesday and Wednesday, Sept. 21 and 22, in the Assembly Room of the American Annex Hotel, St. Louis, Mo. Preceding the first session on Tuesday morning, the members and guests were registered and presented with the usual Institute badges. The morning session was opened at 10:30 by Ralph Arnold of Los Angeles, Calif., Chairman of the Petroleum and Gas Committee. In his opening remarks, he suggested that the petroleum section specialize more and more on the technical problems of the oil industry and that an effort be made to enlarge the membership of the Institute among the technical men of the industry. The following program was presented : OIL FIELDS OF RUSSIA, by A. Beeby Thompson and T. G. Madgwick, of London, England. Presented by H. A. Wheeler; discussed by Arthur Knapp and R. VanA. Mills. This most comprehensive paper was one of what is hoped to be a series to be presented by some of our foreign members. It is by far the best description in English of the world-famous Baku and other fields of Russia.

Jan 1, 1920

By John Wulff

IN a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot profilometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200° and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 415° and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on ½ sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples whose surface temperatures exceed only about 250°C. EXPERIMENTAL PROCEDURE The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, 1 by 1 cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale. On a lapping machine of the Graton2 type, both sides of each sample were polished to a flatness of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any deformations induced by surface preparation. Samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrument shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. Suc-

Jan 1, 1941

By André G. Journel

Geological study of the Prony Nilaterite (New Caledonia) began in 1969 and included drilling, geological mapping and laboratory studies. The deposit is the product of weathering of basic rocks. From top to bottom, the following zones can be distinguished: a compact ferruginous cover; ore associated with yellow laterite, containing 1.0-1.5% Ni and low in impurities (SiO2, Mg); an intermediate silicated ore containing 1.3-2.0% Ni and higher percentages of impurities; garnierite ore much richer in nickel (2-4%) but high in SiO, and Mg contents (Mg up to 20%) ; and parent rock, largely peridotites. Distinction between types of ore is essential because the high grade ore (silicated and granierites) is penalized for its high Mg contents that demand additional acid treatment. All studies made distinguish two types of ore, laterite and silicated.

Jan 10, 1973

By Albert E. Reed

THE development of the modern high-speed vibrating screen, together with the increasing availability of long-lasting stainless-steel screen cloth for relatively fine-mesh separations, means that more screen circuits will be used in the future. It seems pertinent therefore to examine a few characteristics of screen-circuit products, and especially the points of difference as compared with products of classifier circuits. The most noticeable change that takes place when substituting screening for classification in a grinding circuit is a substantial drop in the circulating load, owing to the greater ease with which the "fines" leave the circuit. Where circulating loads of 500 to 600 per cent are considered fairly normal in classifier grinding circuits, the grinding circuit equipped with screens for equivalent work will have a circulating load of only 20 to 75 per cent. As a result, the products of screen circuits will show a minimum of overgrinding or sliming as compared with a classifier circuit. The desirability of this characteristic will naturally vary according to the metallurgical requirement in each case. Because screen separations make a sharper division according to particle size, the products of screen circuits can be expected to show greater crowding of particles near the point of separation. These changes in product characteristics are so important that other factors, both in the grinding and concentration processes must be adjusted if the operator is to take full advantage of the increased tonnages and higher efficiencies available to him through the use of the screen circuit. One factor that too often is overlooked when changing to screen circuits is the importance of adjusting the ball-mill or rod-mill charge, to compensate for: (I) increased tonnage of new feed, (2) decreased circulating load, or (3) more granular character of feed. These same factors should also be taken into consideration for their effect on the various types of concentration or flotation equipment that may follow the screen circuit. Over a period of years, this equipment has generally been designed and adjusted to the product of the classifier, therefore it seems obvious that some research on the adjustment and adaptation of concentrating and flotation equipment to screen-circuit products will be most profitable to the operators. To illustrate the points mentioned above, the results from three recent installations follow, with data on the comparative characteristics of screen and classifier circuits. A range of separation from 10 to 48 mesh has been chosen, using two general types of screening equipment and two types of classifiers. The first of the installations of which the results are to be examined is that of an iron-ore installation where eastern magnetite was being concentrated prior to sintering. Fig. I shows the original grinding circuit, using classification, while Fig. 2 shows the same circuit equipped with a

Jan 1, 1945

By John B. Mitchell

Approximately 90% of all potash produced is employed as a fertilizer, either directly or with nitrogen and phosphorus. The remaining 10% is utilized in the manufacture of other chemical products. The original source of potassium was wood ash, however, today the term potash refers to all commercially important salts of potassium. The world's first potash mining operation commenced in Strassfurt, Germany, circa 1860, and since that time the industry has grown steadily to its present annual output of about 30 million tons of potassium chloride products or 18 million tons of Kg0 equivalent, potassium chloride or "muriate of potash" being equivalent to 63.1 % pure KPO.

Jan 5, 1972

By A. H. Miller

TEMPERATURE considerations are of prime importance in the manufacture of steel products-front the time the metal is produced in the melting furnace, where the chemical reactions have a direct dependence on the temperatures of the bath, to the final machining of work on which the expansion due to the rise in temperature of the forgings during machining must be allowed for. Methods employed and difficulties encountered in some of the more important steps are here outlined. These methods are the result of years of experience, with many methods of temperature determination, and have been successful in routine works practice in the manufacture of high-quality steels. In the operations of melting, forging, and heat treatment, if the product is to be of the best quality each operation must be carefully followed through. A high-quality product cannot be obtained even with the best heat treatment if the steel is poorly melted, and, conversely, the best steel ever made may he spoiled by inefficient heat treatment. To perform the best work in any of these operations, temperatures must be accurately regulated.

Jan 8, 1919

By J. S. Johnson, W. C. McCulloch

ALL phases of plant operation must be synchronized so that the number of interruptions in the flow of material may be reduced to a minimum. In the majority of plants operating under a labor agreement, time lost during the operating shift cannot be made up with overtime. With the work week restricted to 35 hr., the ratio of productive time to total time justifies extra effort in keeping the plant operating at capacity during the productive shift. This does not apply when central plants with adequate storage are operated by multiple shifts. In such installations the problems become similar to those of any factory or mill where added units parallel circuits, or excess capacity serve to maintain the average production during intervals of maintenance shutdown. These plants, by special agreement, may run continuously, barring mechanical interruptions. The control of plant operation is in those procedures that are practiced to obtain from the run-of-mine product a high recovery of clean coal products to meet adopted trade standards and consumer specifications at the lowest possible cost. Correlation of all factors for continuous operation requires more than mechanical perfection in the plant. The run-of-mine coal must be delivered to the preparation plant without delays and the clean coal and refuse products taken away. Power supply and water requirements must be adequate. Signal systems must be established for emergency stops and to facilitate resumption of coal flow. ORGANIZATION Probably the most important item for successful operation of a preparation plant is a capable organization interconnected with the mine organization. A typical organization chart for companies operating in the Pennsylvania anthracite region is shown in Fig. 1. The breaker foreman is in direct contact with the plant preparation operation and reports to the outside foreman, who, in turn, reports to

Jan 1, 1943

By Paul A. Bailly

2.1-1. The Exploration Function in the Mineral Industry. With regard to a new mine, exploration can be technologically defined as all the activities and evaluations necessary before an intelligent decision can be made establishing size, initial flowsheet, and annual output of the new extractive operation based on a certain mineral deposit. The activities that follow such a decision are called first development, then operation (90). Thus, in the U.S.A., exploration may continue in the technological sense after a mineral property has entered the "development stage" as defined for tax purposes. Regulations under Sections 1.615.1 and 1.616.1 of the U.S. Internal Revenue Code state that the "development stage" has been reached when "deposits of ore or other minerals are shown to exist in sufficient quantity and quality to reasonably justify commercial exploitation by the taxpayer" (95). There are, of course, many instances where additional later exploration discloses additional reserves which justify a plant much larger, more efficient and more profitable than the minimum feasible commercial operation. After a surface mine is put into operation, additional search generally will increase the reserves and thus warrant expansion of the rate of output and/or extend the life of the operation. The methods and techniques in such search are similar to those used in predevelopment exploration. This activity has produced a major part of new reserves for all mineral commodities but is not considered as exploration in the context of this chapter. The objective of exploration is, briefly stated, to find and acquire a maximum number of new economic mineral deposits with a minimum cost and in minimum time. The search must be so organized as to maximize the overall probability of discovering commercial mineral concentrations within a minimum time with the funds available. As shown by Celasun (27) these statements are neither adequate nor complete from a pragmatic point of view. Each actual exploration venture must define its objectives in terms of a minimum rate of return on investment for any deposit found

Jan 1, 1968

By John J. Reed

This paper was prepared as a supplement to the general review by Dr. N. G. W. Cook. His analysis of the problem in terms of the strain energy involved in making the excavation is excellent. It will contribute much towards a clearer understanding of rock behavior and control. Several of the practical applications described herein can be directly related to Dr. Cook's theories and conclusions, and are based on the very same principles. CONTROLLED BLASTING IN ROCK EXCAVATION Generally speaking, the natural rock is a relatively strong and competent structural material, if we conserve its inherent good properties and perhaps reinforce its weak spots. The difficulty often lies in blasting out the tunnel or chamber without damaging the walls and roof we wish to have remain afterwards. Much progress has been made in the last five years in better understanding the controlled excavation of rock. The specialized techniques known as smooth wall blasting and presplit blasting have now developed from the status of curiosities of rock excavation to the point where these techniques are specified in contracts drawn up for such rock excavation projects as tunnels, underground pourer houses, etc. These techniques have been well described and discussed in previous publications; there is no need to reiterate here. It might be well to point out that recent research has demonstrated the effect that inherent rock stress may have on presplitting in certain directions. Material can be presplit most readily parallel to the direction of maximum compressive stress, and this may not always be in the direction desired. Inherent rock stress measurements by stress relief over coring, etc., may have important value in deciding how to best presplit proposed excavations. In addition, recent work at the Colorado School of Mines has demonstrated the feasibility of con-

Jan 1, 1967

By H. D. Kessler, F. A. Crossley, J. J. Rausch

The titanium-rich corner of the system Ti-AI-V has been studied to determine the phase relationships in the temperature interval 600° to 1200°C. Metallographic examination of long time isothermally annealed specimens was the principal method of investigation. TWENTY-SIX alloys in the region 1 to 22 pct A1 and 2 to 11 pct V, and the temperature range 600° to 1200°C, were studied as part of a program on phase relationships and transformation processes of titanium alloy systems. Experimental Procedure Preparation of Alloys—Materials used in the preparation of alloys were high purity Bureau of Mines sponge titanium (103 Bhn), 99.7 pct pure V chips obtained from the Electro Metallurgical Div., union Carbide and Carbon carp., and 99.71 pet pure A1 in the form of granulated shot from Aluminum cO. Of The alloy ingots, weighing l5 g, were melted in a nonconsumable tungsten electrode arc furnace un-

Jan 1, 1957

By D. W. White

The kinetics of isothermal transformation of ß-to-u uranium have been studied over a broad temperature range in alloys containing from 0.3 to 4.0 atomic pct Cr. Two modes of transformation are indicated by the existence of two C-curves in the TTT diagram. The upper temperature mode is regarded as a nucleation and growth mechanism, whose rate is controlled by diffusion of chromium in the ß phase matrix. The lower temperature mode is martensitic in nature. The M, temperature increases with decreasing chromium content, suggesting that the two transformation processes become synonymous in unalloyed uranium. URANIUM metal undergoes two allotropic transformations in the solid state. The a phase, orthorhombic in crystal structure,' is stable from room temperature up to about 665°C. The ß phase, characterized by a complex tetragonal structure,' prevails from 665" to about 770°C. The y phase is body-centered-cubic3 and is the stable modification from 770°C up to the melting point (about 1130"). In uranium of reasonable purity, neither of the two high temperature phases can be retained by quenching. However, the addition of certain alloying elements to uranium makes it possible to retain either the y-uranium phase or the ß-uranium phase at room temperature. Chromium alloyed in small amounts with uranium will permit retention of the ß-uranium phase in a metastable state at room temperature upon quenching from a ß-phase temperature.' From available information' on the equilibrium phase diagram for the U-Cr alloy system (Fig. I), it is to be expected that, however sluggish in its rate, the ß phase in such alloys should decompose eutectoidally to a phase and elemental chromium. It was the aim of this investigation to measure the rate and study the nature of this decomposition as a function of temperature and of chromium content. The investigation was reported in classified literature about five years ago and has recently been declassified for publication. In the meantime, there have appeared the papers of Holden,5 Mott and Haines,".' and Butcher and Rowe8 ealing with the metallography and the crystallography of the ß-to-a transformation in U-Cr alloys. These investigators have confirmed several of the phenomenological observations that will be described in the present paper and have examined in considerable detail certain aspects of the transformation and its mechanism. Although all of these investigations have concerned themselves experimentally with U-Cr alloys for the most part, an important consequence has been a clearer understanding of the nature of the ß-to-a transformation in uranium metal itself. Experimental Procedure This investigation dealt with a series of uranium alloys varying in chromium content from 0.3 to 4.0 atomic pct (0.066 to 0.90 weight pct). On five of the alloys, rates of isothermal transformation from the ß to the a phase were measured over a wide temperature range, leading to the development of TTT (time-temperature-transformation) diagrams. Transformation rates were measured over certain narrow temperature ranges on additional alloys. The alloys were prepared by vacuum melting and casting, using zircon or magnesia crucibles and graphite molds. Electrolytic chromium was used as the alloying addition, and the uranium was Mallin-ckrodt biscuit metal that had been vacuum remelted and cropped to remove many of the nonmetallic impurities that had floated to the top of the ingot. The ingots, 3/4 or 1 in. diam, were reduced in size by swaging. Alloys containing less than about 2 atomic pct Cr were swaged at 250° to 275°C, with initial and intermediate anneals at 550°C after every 75 pct reduction in area. Alloys with higher amounts of chromium were swaged at 550" to 600°C, although at the smaller sizes some of them were reduced by the procedure used on the more dilute alloys. Before use as test specimens, the swaged rods were annealed at 700" to 720°C for several hours, followed by slow furnace-cooling. The purpose of the anneal was to achieve the maximum amount of solution of the available chromium into the ß phase, as well as to remove extensive preferred orientation. The isothermal transformation rates were measured dilatometrically, using a quenching dilatometer and an experimental technique similar to those employed by Davenport and Bain in their original work on the transformation kinetics of austenite in

Jan 1, 1956