Search Documents

By P. A. Witherspoon, R. W. Donovan, T. D. Mueller

The use of petroleum-barren aquifers for underground storage has become extremely important to the natural-gas industry. A critical problem in assessing the feasibility of a specific aquifer for such use is the permeability determination of the caprock over the proposed storage project. The approach used here is to conduct both static and dynamic field tests on the aquifer being analyzed. Valuable information on the possibility of communication between the storage aquifer and any other aquifers above can be obtained by measuring hydrostatic water levels and water analyses. Significant differences in such data give evidence of the lack of communication between the intended storage reservoir and other horizons. The dynamic approach requires that one well be pumped in the storage aquifer, and changes in fluid levels recorded in both the aquifer and its caprock. The interpretation of the data from such pumping tests involves the solution of nonsteady radial flow in an infinite aquifer and the influence on such flow of a leaky caprock. A finite-difference model has been used to investigate this problem, and the transient behavior has been solved numerically with a digital computer. It has been found that the pressure transients in the storage aquifer are not affected significantly by moderate caprock leakage. The pressure behavior of the caprock is a much better indicator of the degree of leakage, and generalized solutions for this behavior are included. Field data are presented to demonstrate both the static and dynamic approach. If is concluded that appropriate investigation of the groundwater hydrology in an aquifer-type gas-storage project can provide much valuable information for determining the effectiveness of the caprock to hold gas. INTRODUCTION Underground storage of natural gas in the United States has been developing at a rapid rate over the past few years. In 1955, the total gas-storage capacity was about 1.6 trillion cu ft; by 1961, this figure was almost 3.2 trillion cu ft, an increase of 100 per cent in six years.' This trend un- doubtedly will continue because the economics favor the development of gas storage, as opposed to the construction of new pipelines, to meet the inherent cyclic demand for fuel in the metropolitan areas of this country.' About 15 per cent of the current underground gas storage has been developed in petroleum-barren aquifers, i.e., geological domes or anticlines in which no commercial quantities of oil or gas had been produced prior to the storage operations. The necessity for using barren aquifers outside many metropolitan areas of this country has been due to the lack of depleted oil or gas fields that were near enough and large enough to meet the demands of such consuming areas. Pipeline companies have developed aquifer storage along their transmission lines to meet the fluctuating needs of their complex systems. Considerable thought has also been given to the problem of storing gas in a structureless aquifer, both in this country' and in the Soviet Union outside the city of Leningrad.'," Conditions such as these have led to the development of aquifer gas-storage projects in many parts of the U. S. Most of these developments have centered in the Mid-Continent area, and the greatest amount of activity has been concentrated in Illinois.6 Thus, the use of petroleum-barren aquifers for gas-storage purposes has become extremely important to the natural-gas industry. There are three basic problems in developing aquifer-type storage: (1) finding an adequate geologic structure, (2) finding a suitable storage reservoir within the structure and (3) determining the tightness of the caprock over the intended storage zone. The first two problems can be solved by applying conventional methods of exploration geology, but once these problems are solved, the question arises as to why no oil or gas is present in an otherwise favorable setting. Two situations are possible: (1) an adequate source bed was never present, or (2) a source bed was present but the petroleum seeped away because of a leaky caprock. Determining the tightness of the caprock is one of the most critical problems in assessing the feasibility of a specific aquifer for storage purposes. In attacking this problem, one usually takes cores of the caprock and subjects them to a rigorous investigation. Such core data are desirable, but they only detail the matrix properties and cannot be expected to reveal the gross characteristics of the caprock. Several gas-storage projects in the U. S. have had considerable leakage where

By George L. Porter

Mr. President and Gentlemen of the Institute of Mining Engineers: . Unofficially representing the people of the vicinage, it is my pleasant duty to welcome you to the city of Bridgeport, to the valley of the Naugatuck, to the State of Connecticut. The importance and wide-reaching influences of the investigations for which your Institute is organized, the beneficial results which have directly and indirectly blessed mankind from your and kindred studies, the distinguished position which has been achieved in the scientific world by the Institute as a society, and the personal reputation which is the proper recognition of the ability and knowledge of its individual members, assure all that in attempting to honor you we are ourselves honored. In the republic of knowledge no fictitious rewards dignify the incompetent and the ignorant—the attested success of inventions and discoveries in the workshop of nature differentiates her real citizenship. Your present place of meeting is wisely selected ; for this senti-

Jan 1, 1895

By George L. Lyle

WITH the advent of World War II, the need for agricultural products rose phenomenally and caused a similar increase in demand for plant foods of which phosphate rock is one of the more important raw materials. By the close of the war or shortly thereafter, all of the operating companies were expanding their production facilities. Many companies installed modern bulk material handling facilities. Designs varied, but were generally of the overhead trestle type of storing conveyors. American Cyanamid studied these various installations but was not satisfied with the conventional system because of high initial cost, increased maintenance problems in the way of painting structural steel that might be submerged in stored materials, and because of slightly increased operating costs. As a consequence of these economic analyses, conferences were held with the various conveyor manufacturers to develop a better method of storing and reclaiming. After considerable engineering study, one conveyor manufacturer suggested the unique system which was installed in 1950.

Jan 8, 1954

By Raymond E. Riethmann, Beuford M. Bunnell

The spiral classifier was originally developed for closed circuit grinding It has since been applied very successfully to other classification duties where a two-product size split is required. Inherent operational qualities of this classifier make it ideally suited for sizing, washing, or dewatering materials such as ores, phosphate rock, sands, coal, oyster shells, solar and potash salts. Operating characteristics, flexible design and guidelines for proper application are presented.

Jan 1, 1978

By J. O. Whiteley

IT is difficult to give a refining outline that may be followed for any and all combinations of the platinum metals; different combinations require different methods of attack. This paper does not pretend to go into all of the reactions of the metals of the platinum group, but will outline the commercial refining of platinum scrap. TYPICAL PLATINUM SCRAP As a concrete case, let us take 100 oz. of miscellaneous scrap, made up of jewelry scrap, dental scrap and laboratory ware. This lot will contain some platinum, palladium, iridium, ruthenium, rhodium, gold, silver and copper. The first problem is to get all of the metals in solution. If the scrap is principally platinum, palladium and gold, a treatment with aqua regia is the course to pursue; but if the scrap contains alloys high in iridium or ruthenium, aqua regia will act too slowly. In the case in hand, we are going to presume that we have scrap high in iridium and ruthenium, and proceed accordingly.

Jan 1, 1928

SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II SEC. 1. The membership of the Institute shall comprise four classes, namely: 1. Members; 2. Honorary Members; 3. Associates; 4. Junior Associates. All members shall be equally entitled to the privileges of membership, excepting that Honorary Members, Junior Associates, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. Members shall comprise all those persons who on the third Mon- day of February, 1918, were members of the Institute, and in addition thereto, all those thereafter elected or transferred into the class of Members. A person to be eligible for election or transfer into the class of Members must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. Graduation from the scientific course of a college, approved by the Committee on Membership, shall be considered equivalent to two years' employment, as required in the previous sentence. Employment as a teacher of engineering, mining, geology, metallurgy or chemistry, if in direct charge, may be considered a position of responsibility as specified in the second paragraph. Persons employed in research or any scientific literary work or in teaching in the scientific departments of colleges, approved by the Committee on Membership, who at the same time are engaged in consulting or in the active practice of mining, geology, or metallurgy, shall be entitled to consider the time so spent in active practice as equivalent to an equal length of time of employment in positions of responsibility, provided the work done or the positions held seem to the Committee on Membership to warrant the equivalency. The requirement of three years' employment in positions of responsibility may be waived by the Committee on Membership in the case of persons who have done notable original work in mining, or metallurgy, or have won distinction by research or investigations In one or more of these subjects.

Jan 1, 1928

By Elmer W., Pehrson

NOT much serious consideration was liven to the military aspects of raw materials before World War 1. Following the outbreak of war in Europe in 1914, however. this situation was promptly changed. Disruption of allied shipping and German submarine warfare soon cut off a substantial part of the material the United Staten was accustomed to receiving from overseas. At the same time, raw material requirements rose rapidly as the tempo of industrial preparedness was stepped up in anticipation of war. By April 1917, when we entered the war, serious shortages threatened and consideralde attention was being given to our "deficcient" raw materials. The term "war mineral," began to appear after we became active combatants. But there is no evidence that "strategics" and "critical." as now used, had entered the lexicon of our raw materials experts during the last war nor were there apparently any officially recog¬nized list or definitions of what con¬stituted war materials. According to G. A. Roush in his book, `'Strategic Mineral Supplies," C. K. Leith, while serving as mineral advisor to the War Industries Board. compiled the first unofficial list of deficient minerals in 1917.

Jan 1, 1944

AS provided in Article VIII, Section 4 of the By- laws, the Papers and Publications Committee has formulated the following, rules of pro-cedure and submitted them to the Board of Directors for consideration and approval. In preparing these rules the committee, and an active subcommittee con-sisting of Messrs. Norris, Sharpless; Fohs and Wither-ell, have kept in mind the desirability of codifying the practice that has grown up through the now sev-eral years of experience of the committtee, without casting them in a mold so rigid as to be hampering. The problems of the Institute change from year to year and the methods of publication must change also to meet each new situation as it arises. "The estab-lishment of divisions and special volumes devoted to the papers. read before each required certain changes from former practice. These rules have been framed with this in view. The committee suggested, however, in its letter of transmittal, that the system will be made all the more workable if the Board will, as far as practicable, in making appointments to this committee, arrange for representation from each of the professional divisions and technical committees. It is understood that the chairman of the committee will be named by the Board. The rules regarding spe-cial volumes have been framed, keeping in mind the present policy of distribution, as already approved by the Directors under which the special volumes go only to the special. groups except on request. The committee has not attempted to provide rules governing consideration of any appeal made to the Board from one of its decisions, but its services and files will necessarily be at the full service of the Board in any such event. The rules which were ap-proved by the Board at its meeting on March 30, 1928, are as follows: Signed by C. S. Witherell, Chairman. (A) The authority of. the Committee on Papers and Pub-lications, hereinafter called the Committee, is defined in Art. VIII, Sec. 4 of the By-laws of the Institute, which reads as follows: "Papers and Publications: The Committee on Papers and Publications shall consist of the Secretary of the Institute, and at least twelve members of the Institute, to assist in passing on all papers offered for publication. They shall be appointed annually by the Board of Direc-tors, on recommendation of the President, and shall have authority, subject to appeal to the Board, to accept or reject papers for publication in the Transactions and Technical Publications of the Institute. The Commit-tee shall formulate a set of rules of procedure which, when approved by the Board, shall have the force of By-laws until revoked or amended." The policy of the Committee will be to uphold the ob-jects of -the Institute as set forth in the Constitution (Arti-cle 1, Sec. 2).

Jan 5, 1928

By R. F. Sheldon

Largest uranium deposit in the Northwest is Dawn Mining Co.'s Midnite mine on the Spokane Indian Reservation. The orebodies lie along the contact of granite and metamorphosed sedimentary rock and are controlled by faults and shear zones near the granite contact. In the oxidized zone the deposits consist mainly of the secondary uranium mineral meta-autunite; sooty uraninite and primary uranium minerals are known to occur at greater depths. Elevations in the mine area range from 2500 to 3500 ft. The rolling hills and low, rounded mountains are covered with grass and evergreen trees. HISTORY AND DEVELOPMENT Original showings were discovered with a geiger counter in the spring of 1954 by prospectors Jim and John LeBret. High radioactivity in several schist outcrops was found due to scaly coatings of a greenish-yellow, fluorescent mineral, later identified as meta-autunite. Prior to this time autunite was not known to occur in the state of Washington, and no significant uranium deposits had been found in the Pacific Northwest. Outcrops in the area were few, and most of the ground was mantled with 2 to 10 ft of overburden, but three other radioactive zones were discovered by prospecting the ridge southward along the strike of the schist near its contact with granite for three quarters of a mile. Midnite Mines Inc. was formed

Jan 1, 1960

By AIME AIME

[The American Institute of -Mining Engineers does not assume responsibility for any statement of fact or opinion advanced in its papers or discussions.] A detailed list of the' papers contained in this section is given in the Table of Contents, pages i. and ii. Comments or criticisms upon all papers given in this section whether private corrections of typographical or other errors or communications for publication as "Discussions," or independent papers on the same or a related subject, are earnestly invited. ERRATA. The following corrections and. additions to papers contained in Bi-Monthly Bulletin No. 7, January, 1906,-were received too late for incorporation in the text of said papers ; but will be introduced in their: proper places: in the volume of the Transactions: These corrections are here published in order to bring them -promptly to the notice of the Institute. Page Line Cover, title-page and at the top of pages in the preliminary section "No. 1 " should be "No. 7 ". 1. Bottom For :" Dr. P. H. Shimer" read "Dr. P. W. Shinier " 69. Fig. 3. "N" of compass-record should be ?S". A new block for this illustration has been made as shown on p. xxxviii of this Bulletin. 78. 3 from bottom. For " slope " read " stope." 89. Fig. 2, small diagram in upper left-hand corner. Omit use 50 ft. to 1" scale ". For "Thro' 250 " read " Thro' 200 ". Add dotted line extend¬ing from upper right-hand corner of the square

Mar 1, 1906

By K. Thirumalai, D. P. Schlick

Longwall Technology has a potential of resulting in safety and productivity improvements of U.S. underground coal mining similar to those experienced by the introduction of continuous miner systems. The study presents a comprehensive national evaluation of longwall technology to assess the potential of longwalls to improve health and safety and coal productivity. The study was conducted by the authors during the spring of 1980 as part of MSHA New Technology Coordination activities and with a view to examine the factors that may limit the acceptance of longwall technology in the U.S. coal mining operations. The study points out areas where adjustments need to be made in MSHA regulations and enforcement to help Longwalls. A two-entry longwall system appears to offer a practical method of improving underground coal productivity and safety. Applying regulations that are primarily designed for room and pillar methods to longwall mining, in some instances, reduces the effectiveness and productivity benefits feasible by new technology application. Controlling dust is the single predominant problem in the design and operation of longwalls in the United States. The results of this study points out a need for a coordinated program between government and industries on dust control technologies for examining acceptable technological options to control dust in longwalls without restraining the production capability of the system.

Jan 1, 1981

By H. F. McCullough

MECHANICAL loading and conveying equipment has been available for the coal-mining industry for more than twenty years. The earlier equip-ment-was admittedly crude and ill-fitted to perform its intended functions, but there are available today a variety of mechanical loaders and conveyors which may be said to be almost on a par with coal-cutting machines. Despite the fact that such equipment is available and that better and other types of equipment are continually being developed, mechanical loading of coal cannot yet be said to be economically successful, except in a few special cases. It is not an accomplished fact in the sense that machine cutting of coal and electric haulage are accomplished facts and a part of accepted practice. There are two general opinions why we have failed to obtain better results with mechanical loading and con-veying equipment. The equipment manufacturers will say that coal-mine operators have generally failed to establish and maintain the conditions required for suc-cess. The coal-mine operator says that the equipment is not adapted to cope with his specific conditions to the extent required for economically successful results. Just what is the objective of this movement toward mechanical loading? We speak of mechanical loading in such a way as to lead one to believe that we are mere-ly seeking a mechanical equivalent of the human loader and his shovel. Really, we are impressed with the fact that the coal-mining industry has not advanced toward greater productive efficiency to anything like the degree achieved by practically all of the other productive in-dustries, and we are seeking the means to remedy this. We have seen the advantages which follow the intro-duction of coal-cutters and electric haulage-locomotives. The loading of coal is the one major operation in coal mining which has not been mechanized. We believe that a satisfactory, mechanical substitute for the man with the shovel will help us increase our productive efficiency to the same degree as has been accomplished in the other productive industries.

Jan 3, 1927

By W. J. Shearer

A COMPARISON of statistics relating to coal min-ing in Great Britain and the United States leads one to suspect widely differing conditions and practice. A brief review of some of the conditions may enable American mining men to appreciate more fully the difficulties with which British engineers are faced, and to some extent explain why American, coal can be sold f.o.b. mine at the present time at about 50 to 60 per cent of the cost of British coal at the mine, and why British man-shift outputs fall far below American at present being less than 30 per cent. Bulman gives the average depth of 6-ft. seams. in Britain at 1350 ft., and of 2-ft. seams at 517 ft. George S. Rice states that 90 per cent of American coal 'is taken from less than 600 ft. Much English coal is taken below 2000 ft. and some below 3000 ft. The total influence of depth on cost is not always evident. Room work as known in America becomes less advisable with increasing depth, as pillars crush badly if left -for any length of time. A limited amount of bord and pillar work, taking very small amounts of coal in the first working, takes the place of room work, with rapid working of the pillars as soon as the panels are broken. Ventilation difficulties increase tremendously with depth and thinning coal. In America the chief use of air underground is to dilute gas. In Britain it serves a dual purpose, in many cases the amount of air cir-culated being far in excess of the quantity necessary to dilute gas to reasonable proportions. At great .depths rock temperatures exceed-95 deg. F., and great volumes of air are necessary for rock cooling. At these high temperatures humidity becomes an important factor. At present a great deal of research is under way to find methods of overcoming the troubles experienced with high temperature and humidity in deep mines.

Jan 8, 1928

EVERY mould, of whatever kind it may be, must have an entrance appropriate to the material if it is wished to fill its inner space with bronze or other metal. It is likewise necessary that it have vents, that is, air holes, for there is nothing that is not full of air even though it be called empty. Now, molten bronze is a material that has an immediate effect because of its heaviness, and because it is as hot as fire or even hotter,

Jan 1, 1942

By R. Steven Maxwell, Ulrich Petersen

Most minerals have experienced a slow hut perceptible decline in their annual primary production growth over the past hundred years. This decline is due to a combination of factors: (1) increased recycling; (2) exhaustion of the more accessible or higher grade ores; (3) partial substitution; (4) the more efficient use of materials; (5) progressive saturation of markets as living standards rise. Therefore, future demand for new mineral resources will probably be lower than anticipated. As the world population stabilizes, this slowdown in production growth will become even more pronounced.

Jan 1, 1979

By M. F. Trice

PYROPHYLLITE is a hydrous aluminum silicate (A12Si4O10(OH)2)1 that occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.1 The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey,2 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, "are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. SOURCES At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This

Jan 1, 1940

By John P. Weir

Coal's participation in the domestic energy market depends to a very large extent upon the cost of coal delivered to consumers. Today the principal use of coal in the U.S. is in steam-electric generating stations. Generally, it is the delivered cost per million Btu's that is given the greatest weight in choosing either oil, natural gas or coal as the fuel used in these power plants. There are three major cost components of generating electric energy in steam-electric plants. These expenses expressed in terms of "dollars per kilowatt year" are: (1) operation and maintenance of necessary facilities, (2) fixed charges of necessary capital investment, and (3) fuel. For a modern large plant, the first two items would be approximately as follows:

Jan 9, 1962

By Damon H. McFadden

5.1-1. Geographic and Geologic Factors. Surface mines are located where the coal seam can be economically uncovered and where the product can be utilized competitively with other fuels. The planning and designing of a pit may follow various procedures. The sequence for consideration of the influential factors as considered here may not be complete for every pit, nor will it be necessary to be completely used in each design. It is suggested as a check and outline for the engineering approach. Controlling conditions for the layout should be listed and considered with the facilities and equipment for the exploitation. After these items, as listed below, have been discussed and the feasibility agreed upon, then the actual planning and design of the pit can be done. GEOGRAPHIC FEATURES. The location of the coal area sets the climatic stage. The rainfall, the temperature extremes, and the general weather conditions all affect the design of the pit. Overburden soil when wet may not be stackable and may be impossible to move by standard procedures. The coal seam itself may be so soft that it must not be traveled on when wet, as the losses may be the difference between a profitable venture and an unsuccessful one. Some equipment will work well on dry soil only, just as a dredge works only in the wet. The conditions must be checked and analyzed. Some equipment cannot handle frozen soil (wheel excavators), so temperature extremes must be noted. The extreme weather conditions may also govern the expected working days and therefore the ultimate production. The altitude (atmospheric pressure) may affect the equipment, and this should be checked. All of these conditions should be noted on the preliminary map of the area. GEOLOGIC FACTORS. The geologic and surface conditions of the coal field dictate the type of pit generally feasible. Rough terrain, rolling terrain,

Jan 1, 1968

G. R. GOHN. l-1n Table I11 of The Sager, Brown, and Mears paper, which was presented on the screen, data were given showing the results of accelerated corrosion tests of certain magnesium alloys. Mention was made that these were carried to a certain time which was used as a measure of failure but no mention was made as to the period of time. I would like enlightenment on that. G. F. SAGER (Author).-In reply to Mr. Gohn's question regarding the times of exposure for the accelerated stress-corrosion tests referred to in Table I11 of our paper, which shows the correlation between accelerated and atmospheric stress-corrosion tests on magnesium alloys, I can say that we usually run the accelerated tests on such alloys for at least 500 hr. We feel that this is long enough to reveal any marked susceptibility to stress-corrosion cracking. In the case of the atmospheric tests on such alloys, we have not yet decided how long we should expose the specimens. Most of them are being exposed for indefinite periods and a good many of our specimens have now been exposed for several years. We may want to continue some of the tests for five or ten years. The period of six months mentioned in connection with the times of exposure for the atmospheric specimens was a rather arbitrarily selected minimum time for which specimens had to be exposed before we counted them with those that had not failed. A fairly large number of magnesium- alloy specimens have been exposed in the atmospheric stress-corrosion tests at var-

Jan 1, 1945

By S. S. Arentz

An organized safety program has reduced accidents at Pioche because effort is first devoted to arousing and maintaining interest in safety, followed by training in accident prevention, assigning responsibility for the detection and removal of safety hazards, and finally, by keeping score through an adequate system of records. A health program is intergrated with the safety program.

Jan 2, 1950