Search Documents

By Reinhard H. Wöhlbier, George E. Aiken

8.4-1. Introduction. Surface excavating is done on a continuous basis with a variety of machines: 1) trenchers and ditchers, 2) conveyor loaders, and 3) bucket-chain and bucket-wheel excavators (BWE). Surface mining is largely concerned with only the last two machines, although some of the conveyor-loader types are often used by contractors for large-scale earth moving, and the engineer should be aware of these applications. This chapter is restricted to discussing only the bucket-chain and bucket-wheel excavators, with special emphasis on the latter. Continuous digging with these machines is done with evenly spaced buckets on either an endless chain or on the periphery of a rotating wheel. The bucket-chain digger excavates and takes the material away from the face with the same machinery. In the case of the bucket-wheel machine, these two functions are separate. Material is excavated by the buckets and then flows in a continuous stream via a transfer to the conveyor system, which in turn transports it to the discharge point. The wheels are adjustable in rpm and mount 6 to 12 buckets of equal size. These are classed as celled, cell-less or semicelled. The digging ladders for both types can move simultaneously in the horizontal and vertical planes. Ladder control is similar to the operation of a bucket-line dredge. Some ladder-chain and all wheel excavators have the machinery deck and superstructure mounted on a 360° swing circle. Other chain diggers have a fixed machinery deck. Deep and/or high cutting models are available in either the chain or wheel excavator. Machines can be either rail or crawler mounted, but the trend is to crawlers. Many of the early ladder-chain, rail-mounted excavators have been converted to crawlers. These may be either of the single or bogie type, depending on the conditions. Large machines usually use the superior three-point crawler suspension.

Jan 1, 1968

By Oliver Bowles

WHILE vast quantities of limestone and dolomite. are used in metallurgy, the estimated production in 1926 being 23,860,000 tons, there are many problems connected with their use which have not received adequate study. The literature of metallurgy is notably lacking in comprehensive discussions of fluxing or furnace stone. Approximately 900 lb. of limestone is used for every long ton of pig iron produced in the blast furnace, but this important constituent of the charge receives little attention compared with the intensive study that has been applied to ores and fuels, the other important constituents of the charge. In an effort to elucidate some of the doubtful points, the writer has made a wide review of metallurgical literature, and has had the disappointing experience of finding not more than a paragraph or two on metallurgical stone' for each two or three thousand pages of literature reviewed. Furthermore, the limited information supplied is in some instances contradictory and even absurd. For example, a correspondent in a reputable metallurgical magazine classifies magnesia and silica together as impurities in flux "that must be melted and run off as slag." From the furnace operator's viewpoint it is desirable that as complete knowledge as possible be obtained concerning the effects of chemical composition and physical character of the stone on its action in the furnace and on the quality of the metal produced. A better knowledge of these features is advantageous also to the quarry operator in that it enables him to work more intelligently in producing stone that will best satisfy the metallurgists' requirements. The following pages comprise a brief compilation of data now available. Much of the information is well established and probably acceptable to most metallurgists. On some points there is room for debate, and the chief purpose in presenting a paper at this time is to arouse discussion which will throw more light on controversial points and thus assist the author in preparing a more comprehensive and accurate discussion of metallurgical limestone problems.

Jan 1, 1928

By F. F. Peng, A. D. Walters, M. R. Geer, J. W. Leonard

INTRODUCTION Washability characteristics derived from float-and-sink analysis in Chapter 4 demonstrate that coal is intrinsically heterogeneous, and this heterogeneity is also evident in the proximate, ultimate, and size analyses. A range of particles from high to low specific gravity is usually seen in the run-of-mine coal. One objective of coal preparation is to recover the high quality float material (the particles of lower specific gravity) such that the recovered product meets certain quality specifications, as well as to reject or recycle low quality particles of higher specific gravity. The maximum recovery of cleaned coal at the required quality is of major concern to plant operators. However, the quantity and quality of products of coal cleaning, determined in the operation of actual commercial cleaning plants and by theoretical calculation based on run-of-mine washability studies, are known to be different with each coal. Therefore, during the last half century, coal preparation engineers have repeatedly sought methods to predict the technical and economical efficiency of separation of cleaning equipment and systems. Many formulas have been proposed by international investigators to evaluate the efficiency of various coal cleaning operations, primarily based on the yield and/or ash of the various products of coal cleaning. Performance criteria in use today are capable of defining all of the important aspects of a given concentrating operation; however each criterion has certain restrictions or limitations. It is important, therefore, to understand how such formulas can be used and the problems involved in their construction. Technical Measure of Plant Performance Conventional means for evaluating a preparation plant's performance are generally approached through the use of equipment performance mea-

Jan 1, 1979

By Thomas Darlington

THE obligation of an employer to the State requires certain things of him as matters of good citizenship: for instance, that his workmen shall have a living wage, that child labor shall not be employed, that injuries from accidents shall not- make workmen a charge upon the State, and that the laborer's children shall have opportunity for education and to become good and useful citizens. Affairs of this kind are not taken up as philanthropy, for the officials of a corporation or a large manufacturing concern may not feel at liberty to spend the funds of their company as prompted simply by motives of kindliness; but they may spend company money on such matters because it is good business. For years, the poisonous effects of lead, phosphorus and dust have been emphasized in books on industrial hygiene and their elimination has been urged; but the more important and everyday physiology of the workman himself has been neglected. Part of my object in writing this paper is to show how our knowledge of physiology may be applied to working conditions in everyday life. In the interest of industrial laborers, accident compensation laws have been enacted in 33 States. This has been carried forward rapidly, because it has been shown that it pays both employer and employee. A further step is the recognition of sickness and disablement independent of accidents, not only because of their immediate cost to the worker and to the employer, but because continued efficiency in work and business depends largely upon health. Some measure of the importance of health in industry can be gained by the knowledge that records kept by some companies which now make this the subject of careful inquiry show that the time lost by employees, through illness; is several times as much as that lost as the result of industrial accidents. It is true that accidents frequently result in permanent disability or death, but it is equally true that illness is also a cause of permanent disablement or death. Thus the chief difference is that the loss to the employee through accidents occurring in the course of his employment is now generally recognized as a cost

Jan 2, 1918

By M. D. Hassialis, C. G. Myer

THE nature of a collector-coated mineral surface has been the subject of some experimentation and much speculation. Various aspects of the problem have been isolated and studied; it is probable, however, that there exist aspects as yet unrecognized, which are needed for a complete description of the system. The recognized elements of the problem are: 1—The nature of the chemical units comprising the film and the nature of the forces holding these chemical units to the mineral surface; 2—The orientation of the chemical units at the surface; and 3—The disposition of the collector units at the mineral surface. This report touches upon all three aspects of the broad problem; it deals, however, with a new and heretofore unrecognized element—the mobility of the collector units in the two dimensions of the solid-liquid interface. Regardless of the viewpoint adopted as to whether the chemical units comprising the collector film are collector ions or molecules, held either by chemical or physical forces, the writers on flotation theory are in apparent agreement as to the orientation of the chemical units at the mineral surface. Wark and Cox' showed that the contact angle at a stable collector-coated surface in a constant chemical environment is independent of the nature of the mineral and of any resurfacing agent; it depends solely upon the collector used. They showed further that the value of the contact angle increases with the number of carbon atoms in a homologous series of compounds. Taggart, Taylor, and Knoll2 postulated that the collector ion is oriented with the chemically reactive, polar end toward the mineral surface and the non-polar, hydrocarbon-like end toward the liquid phase. In support thereof they cited the abstraction of p-p1 dihydroxydiphenylthiourea and of glycol xanthate8 by galena without a concomitant increase in the contact angle above that of clean galena. It was argued that in these cases the water-repellent layer which normally would be presented to the liquid phase owing to the orientation of the collector ions is overlain by a layer of water-avid groups, the hydroxyl groups. Implicit is the analogous orientation exhibited by a monomolecular layer of an insoluble substance at an air-water interface. It should be pointed out that these facts also are consistent with the concept that the collector units be flat on the surface of the mineral and that the response of the surface to an air bubble is determined by the ratio of the area covered by water-avid groups to the area covered by water-repellent groups; the areas being weighted according to the relative watef-avidity or water-repellency of the groups involved. The disposition of the chemical units of the collector film at the mineral surface has not received the attention it merits. Taggart4 concluded from the observed stoichiometry of the ions entering and leaving a surface that the stoichiometry is obeyed in detail at the surface of the mineral. Thus, in the case of xanthate-coated galena, pairs of xanthate ions are attached to surface lead ions. In the case of chemisorption, Gaudin and Preller postulated an agreement between the atoms or ions of the substratum (the mineral surface) with those of the superstratum (collector film); in the case of the physical adsorption their position is not clear. In one place they state "the first type (physical adsorption) does not require any agreement between the atoms or ions of the substratum with that of the superstratum" and in another place that "It seems, in fact, as though some slight influence of the substratum is formed even in physical adsorption." The present work shows that in some cases of chemisorption the chemical units of the collector film are in constant surface-bound motion and may not be assigned to any site of the surface, hence there is no permanent association between the chemical units of the film and the atoms or ions of the solid. The physical property of the collector film that is of paramount importance is its surface energy. Although this property is not susceptible to direct experimental determination, the related contact angle is. Much of the knowledge of the properties of a collector film derives (by deductive and inductive reasoning) from the behavior of an air bubble thereat

Jan 1, 1952

By Walter H. Ortel, George B. Wallace

INTRODUCTION A greater understanding is required about the factors which control tunneling operations if we are to meet the expected demand for tunnels. Much of the needed information can best be achieved by the proper use of instrumentation and advanced engineering concepts. Tunnel measurements and their analysis may prove to be the key which will give the insight necessary to understand the relationship of rock, tunnel supports, and linings. There are three main areas which can be improved through the use of tunnel instrumentation. First, and of prime importance, is safety for men and the project. When unstable conditions occur, sets become distorted. Even without measurements, it is sometimes possible to tell when trouble is approaching. In effect, the set acts as a load cell. Distortions in the set indicate reinforcements may be required to maintain stability. Additional sets or rock bolts, if they are placed soon enough, may provide this stability. However, when large rock displacements occur in short periods of time, it could be too late. Figure 1 is an example of the difficulties encountered in stopping moving rock. To stop the movement and possible failure, large props were placed above the spring line and the massive concrete gravity buttress was constructed along the legs. Rock bolts from the buttress deep into the rock were also used in an attempt to stabilize the rock mass. However, this work is for a highway tunnel and eventually these props and buttresses must be removed.

Jan 1, 1971

By J. F. Wolff

EXPLORATION of Lake Superior iron ores is done principally by drilling. The soft iron ores are churn drilled and the harder ores are diamond drilled. In exploratory work in the harder formations, where the diamond drill is used, the sample comprises both core and cuttings. The care given in handling and preserving the core depends on the im-portance that may be attached to certain characteris-tic strata in different formations. The following instructions for the care of core samples are issued by the Oglebay Norton Co. for diamond drill work done for them on the Gogebic Range of Michigan: The driller shall be careful upon removing the core from the core-barrel to keep the core in exact order. Not only should the pieces of core be kept in exact relation to each other, but care should be used not to turn them end for end. Core should be placed in the core-box from left to right in each row. Each drill should be furnished with small, hinged cover core-boxes, and each drill should be well supplied with empty boxes. Core remaining at the drill when the drillers are not working should be locked up. The practice of picking sample pieces of core and carrying them away from the drill to be examined in better light, or shown to someone else, is unnecessary and prohibited. The reason for this is that these pieces are seldom returned to the core-boxes and valuable information or "markers" may be lost. If the inspector suspects that a critical point is reached in the drilling and he cannot determine at the drill, he should remove the entire core-box and see that the drill is immediately furnished with an empty core-box. It is customary to split the core longitudinally so that one-half may be ground to a pulp for analysis and the other half may be kept for future inspection. The core should be filed in permanent core-boxes, properly labelled, if the core is to be kept in exact order as taken from the core-barrel. Otherwise, it is often filed in tin boxes inn the way that sludge samples are filed. To obtain the average analysis, the core and cutting samples obtained in the same run are analyzed separately and the analyses are combined in the proper ratio.

Jan 9, 1922

Since 1571, when the Institute was founded, many of the most important papers in the English language, on the various phases of mining and metallurgy, have appeared as Institute publications. As members of the Institute regularly receive the publications in which they are interested, this discussion is primarily for nonmembers who wish to know of them. The Institute has several means of issuing papers which have been submitted and accepted. The monthly journal, Mining and Metallurgy, is the magazine of the Institute. In it appear notices and reports of official business as well as many papers and contributions which do not appear otherwise. The annual subscription price of the magazine to nonmembers is $3 per year; Canadian and foreign postage $1 extra; single copies 50 cents; back issues $1 each. Many papers are published separately each year. They are issued in one or the other of two numbered series; namely, Technical Publications and Contributions, and of the latter there are four forms: Preprints, Mimeographs, Reprints, and Unpublished Manuscripts. A Technical Publication or Contribution (in any form) is issued by the Institute when it is listed in Mining and Metallurgy. Technical Publications are sent automatically to members who have asked in advance for papers on a given subject. All members are entitled to a copy of every paper in either series, except when a Contribution is an Unpublished Manuscript. Con¬tributions in the form of Unpublished Manuscripts are filed in the Engineering Societies Library and copies of some of these papers may be found in a few selected libraries throughout the country.

Jan 1, 1933

By Gerald Sherman

(San Francisco Meeting, September, 1915) THE ore deposits of the Warren district, in which the mines of the Copper Queen Consolidated Mining Co. are situated, have been described in a number of technical publications, and will not be-discussed here in detail. Certain of their characteristics, however, control -methods of underground transportation and hoisting of ore. In the Copper Queen mine, the majority of the ore has occurred in a zone encircling the west boundary of the porphyry intrusion of Sacramento Hill. It has a width varying from 800 to 1,200 ft., and a thickness of about 400 ft. It reaches the surface in the older part of the mine to the northwest, but dips to the southeast, where it is reached at 1,400 ft. below the Czar collar, in its farthest extension at present developed on Copper Queen ground. There is one major extension from the northwest end of the zone toward the west along the Czar fault, and others of minor importance. Individual orebodies are scattered through the zone in an eccentric manner, only matched by their own irregularities of form and size. Their most general characteristics are the softness of the ore and their great horizontal rather than vertical extent. It has been estimated that the average vertical thickness of ore in the Czar and Lowell divisions is between 30 and 35 ft. It is calculated by assuming it to be uniformly distributed over its horizontally projected area. In this zone, and for some distance above it, the ground has been .subjected to intense alteration and intense but irregular oxidation. It has resulted in an enormous quantity of earthy or clayey material, which may be either ore or waste, which when wet is both heavy and tenacious. Below alteration, the ground is fairly hard, and the limestones contain primary ores differing from those heretofore considered typical of the camp, and which have not yet been thoroughly exploited. The mine production has been drawn from many orebodies spread . over a great area. A diagram map (Fig. 1), of haulage drifts and loading stations, illustrates the situation in 1914.

Jan 9, 1915

By Arthur Taggart

FLOTATION of ores is a practical utilization of the energy that resides in the surfaces of solids and liquids. The best known manifestation of this energy is called surface tension; an equally important, though less apparent, phenomenon is adsorption. This paper reviews some of the recent investigations of these phenomena, and gives the results of certain experiments performed by the authors. Surface tension is a manifestation of energy having its seat at the bounding surface between the adjacent phases of a multiphase system. Thus, at the interface between a liquid and a gas, or between two immiscible liquids, or between a solid and a gas or a liquid, there are forces capable of doing work, their magnitude depending on the nature of the adjacent phases and the extent of the bounding area. These surface forces are inappreciable when the ratio of surface to volume of the adjacent phases is small, but they become powerful when this ratio becomes large, as it does when one of the phases is highly dispersed. Froth flotation, which consists in buoying solids heavier than water to the surface of water by means of gas bubbles, utilizes the force of surface tension to attach the solid particles to the gas bubbles and again to maintain the floating mass of bubbles as a more or less persistent froth at the surface of a pulp for a sufficiently long time to allow its removal. It follows from the second law of thermodynamics that the potential energy of a system in equilibrium is a minimum. Therefore a multiphase system, tending toward equilibrium, will arrange itself in such a way that the total energy of the interfaces will be the least possible. This end can be accomplished in two ways: by a change in shape that will reduce the interfacial area; by a change in the nature of the surface layer in

Jan 8, 1922

By William E. Ford, Edward Salisbury Dana

436. Electrical Conductivity. - The subject of the relative conducting power of different minerals is one of minor interest.* In general most minerals, except those having a metallic luster among the sulphides and oxides, are non-conductors. Only the non-conductors can show pyro-electrical phenomena, and only the conductors can give a thermo-electric current. 437. Frictional Electricity. - The development of an electrical charge on many bodies by friction is a familiar subject. All minerals become electric by friction, although the degree to which this is manifested differs widely. There is no line of distinction among minerals, dividing them into positively electric and negatively electric; for both electrical states may be presented by different varieties of the same species, and by the same variety in different states. The gems are in general positively electric only when polished; the diamond, however, exhibits positive electricity whether polished or not. It is a familiar fact that the electrification of amber upon friction was early observed (600 B. C.), and indeed the Greek name

Jan 1, 1922

By John H. Ratcliffe, Hans T. Lundberg

In airborne gravity surveys effects of acceleration and irregular movements of the aircraft must be balanced out or overcome. The gradient of vertical gravity is recorded, therefore, by using two masses instead of one. As the amplitude variations are infinitesimal and difficult to measure accurately, at of gradient during flight is positive or negative. The positive portions of the pattern can then be indicated and contoured. Even with these simplifications, the source of energy must be exceptionally stable. General Principles: In the conventional gravimeter the weight of a standard mass is determined at a number of selected points within the survey area. In most systems weight is determined by comparing the gravity pull with extension or torque produced in a wire spring. The instruments employed are sensitive to the slightest movement; they cannot be used on a moving platform unless velocity is kept strictly uniform.

Jan 8, 1959

By J. H. Frye, R. M. Treco, J. W. Caum

IT has been suggested that: "Insofar as the hardening due to a solute depends upon the increase of lattice parameter produced by it, it is reasonable to suppose that this hardening might be related to the resistance which the pure solvent would offer to increase in its parameter."1 It was further suggested that this hypothesis might be examined by comparing the hardnesses of analogous silver and copper alloys, since the stress necessary to produce a given lattice expansion is quite different in the two metals. Suitable data 2,3,4 are now available on these alloys, and we shall proceed to an examination of the hypothesis quoted above. HARDNESS, LATTICE PARAMETER AND IONIC OVERLAP Increase in ultimate Meyer hardness has been plotted against increase in lattice parameter in Figs. I and 2, It is believed that most of the values are accurate within the limits indicated by the rectangles, These data are also presented in Table I. Ultimate Meyer hardness, Pu, is defined by the equation: [P" - D2] where L = load, D = diameter of an impression having the same diameter as the testing ball, which in this case is 4 mm. Increase in lattice parameter is defined as the difference between the lattice parameter of the solid solution and that of the pure solvent. The curves in Figs. I and 2 are based on equal solute concentration and an equal degree of plastic deformation pro¬duced by the testing ball. Hardnesses are corrected to a constant grain size for copper and silver alloys, respectively, and these two grain sizes are approximately equal. Furthermore, all solutes are from the same period of the B subgroup of the periodic table as their solvent. [ ] The question arises as to whether or not lattice parameter is the only factor controlling the hardness of these alloys. There

Jan 1, 1943

By Paul T. Allsman

1.1-1. Current Status. The history of surface mining is essentially that of mining coal, copper, and iron ores, and the nonmetallic minerals--clays, gypsum, phosphate rock, sand, gravel, and stone. Table 1.1-1 is a comparison of the estimated world production of crude metallic and nonmetallic ores and coal with that of the United States for 1964, in short tons. It includes an estimate of the quantity produced by surface mining methods. Two-thirds of the 8.8 billion tons are mined from surface, ranging from a third of the coal, half the metallic ores, and nearly all clays, stone, sand, and gravel. In the United States, production by surface methods parallels that of the world with two major exceptions: 74% of copper ore and 90% of usable iron ore are mined from the surface, whereas outside the country less than 40% of copper ore and only 50% of usable iron ore are mined from the surface. In surface mining of both metallic ores and coal, much waste is stripped, but in mining nonmetallics the ratio between waste and ore is small. Assuming that the stripping ratio for surface mining in the United States will apply equally to world production, it is estimated on a weighted basis that over 21 billion tons of waste, or a total of nearly 27 billion short tons of material, are mined annually in the world by surface methods. Data are not available to confirm the assumption for waste stripping outside the U.S., but the estimate expresses an order of magnitude that is worth noting. Table 1.1-2 shows the materials-crude ore, coal, and waste-mined by surface methods and the relation to total mined by both surface and under- ground methods in the United States during 1964. Eighty-two percent of all crude metallic and nonmetallic ores and coal was mined from the sur- face, including 82% of metallic, 96% of nonmetallic ores, and 35% of coal. Copper and iron ore comprise 83% of the metallic ores mined from the surface, and clays, gypsum, phosphate rock, sand, gravel, and stone

Jan 1, 1968

By M. R. Geer, J. D. Davis, H. F. Yancey

ALTHOUGH the mechanical cleaning of coal is carried out at plants on the surface, preparation is actually begun at the face in the mine. Here the character of the coal and the amount, character, and distribution of the impurities within the bed may be seen. Blasting methods, dust-allaying procedures, location of mining cut with respect to bands of impurity, and the practice of discarding segregated impurities underground, all have an important bearing on the successful operation of surface cleaning units. The most important single characteristic of both coal and its asso¬ciated impurities from the standpoint of cleaning is specific gravity. Other characteristics related in one way or another to the preparation of coal are rank, petrographic composition, structure and hardness, and friability. These and still other coal properties are discussed in the first section of this chapter and impurity characteristics in the second. COAL CHARACTERISTICS RELATED TO PREPARATION Rank As a result of work done over a period of several years by committees of the American Society for Testing Materials and the American Standards Association, standard specifications are now available showing the classification of coals according to rank and quality of grade.' The term "rank" expresses the degree to which the original coal-forming material has been changed by metamorphism through successive stages from peat to anthracite. Table 1 shows the classification of coals according to rank as devised by the committees of the organizations mentioned. The basic scheme of classification for the higher-rank coals is according to

Jan 1, 1943

By AIME AIME

NO ADEQUATE salary scale, at the present time, can ignore the increase in the cost of commodities 'during the last few years or- afford to assume that this increase is merely temporary. A study of the change in prices and wages during and after the Civil War is of interest in connection with changes that have taken place from 1913 to 1919. The curves on the accompanying figure, based on reports of the War Industries Board and Department of Labor, show these changes. During the Civil War retail prices rose to 164,2 per cent. of the prices of 1860, during the next 8' or 10 years. It is interesting to note that the rise in wages during the Civil War was almost simultaneous with the rise in the prices of commodities. During the World, War, the rise in wages has lagged about a year behind the rise in prices. Furthermore, in the period immediately, following the Civil War, wages continued to rise after prices started to fall, The present price level is not considered merely temporary by such of our Government agencies as the Department of Labor and the Federal Reserve Board or by such economists as Irving Fisher' and J. S. Holden.2 Sub-

Jan 1, 1920

By Roswell Johnson

ALL strata not yielding oil or gas in commercial quantities or a corresponding amount of water may be called dry in a wide sense. In petroleum geology,, however, we may exclude all sands of too low or fin porosity to yield gaseous or fluid contents to the hole drilled in the sand before any original pressure that its contents may be under is disturbed. Most rocks are of this class and they are not reservoirs in our definition; their "dryness" is wholly a matter of course. What are the contents of the pores or what is the exact porosity of such rocks is of almost no concern to us, for economically they are "dry." What does interest us is the content of a rock having sufficient porosity and the pores of sufficient size to yield oil or gas in commercial quantities, if they were present under original pressure: Dryness of these reservoirs is a matter of supreme practical importance. Three views current as to such dryness seem, to me, to apply in a few cases only. It is the purpose of this paper to give reasons for this position and for believing that, in ordinary sedimentary rocks, there is only rarely a reservoir of competent porosity and undisturbed pressure that is dry in the sense of not yielding water, oil, or gas when first penetrated. 1. Gardner1 writes of some Kentucky sands, "There has never been present any salt water or other water in the sand." Absence of water cannot demonstrate this position. It is necessary to show that the rocks were not laid down in water, but in air, and that they became so enclosed, while still above the water-table of the, ground water, that water has not been able to enter since. Most of these sands, and certainly the productive limestones, were deposited in water; and such sands as have been commercially productive show no reason for believing that the overlying shale or limestone was not laid down progressively from one direction and in water that would have flooded it. No adequate explanation has been offered for this hypothesis, which is so inherently improbable.

Jan 1, 1920

By Van Der Muelen P. A.

SOME time ago, the writer received from W. 0. Borcherdt, Manager of the, works of the Bertha Mineral Co. at Austinville, Va., several specimens of a dense yellowish slag-like material, containing cavities showing clear needle-like crystals, and representing a product formed by the fumes of zinc oxide and basic lead sulphate from the oxide furnace, attacking the firebrick lining of the flues. The matrix, which is of a greenish-yellow color, is made up chiefly of an amorphous glass, carrying numerous crystals, the latter being well-defined, clear, and transparent, but colored a very light yellow by small amounts of ferric oxide. A number of the crystals were carefully separated from the matrix and tested with the blowpipe. They have a fusibility of about 2, yield a globule of lead and a coating of lead oxide before the blowpipe on charcoal, and contain some zinc. Their hardness is 5 to 6. 1 Fig. 1. Under the microscope the crystals appear to be made up of a prism, with narrow faces, and a fairly large pinacoid, but unfortunately show no terminal faces (Fig. 1). Between crossed nicols they gave parallel extinction in. the three planes containing the crystallographic axes, and are therefore orthorhombic. The index of refraction is high. A number of the best crystals were measured on the reflection goniometer, the angles given below representing the average of measurements made on different individuals. mm = 46° 52' mb = 66° 34' a:b:c = 0.4334:1 :?

Jan 5, 1917

By Richard L. Gordon

Minerals long have been important commodities in international trade. As an inevitable result, the governments of the world have employed a wide variety of programs that affect the flow of trade. Roughly speaking, we may distinguish between the desire of more developed countries (MDCs) like the United States, western Europe, and Japan to control imports of minerals and the concern of less developed countries (LDCs), like India, about exploiting and exporting their minerals. The terminology used to describe different countries and the classification of specific countries into groups is unsettled and often changing. The poorest countries have been characterized as backward, undeveloped, underdeveloped, and developing. The problem seems to be in selecting a term that is both accurate and polite. Less developed seems, for reasons outlined by Hagen [pp. 51-57], the most convenient term. The borderline between an LDC and an MDC is always open to dispute. Objective measures are difficult to develop because of deficiencies in basic data, and enormous conceptual problems arise in making valid comparisons from even good data [see Hagen, pp. 7-28]. Thus, policies of the MDCs can be evaluated chiefly by using a few basic arguments for protectionist attitudes towards international trade. In dealing with the LDCs, a more far-ranging evaluation that covers general economic policy goals, the role of foreign investment, and the indirect effects of trade is required. This duality breaks down when trying to deal with the depressed areas in an MDC; here the issues are more akin to those associated with problems in an LDC. Similarly, variants of arguments used in LDCs appear in debates about foreign investments in MDCs. The whole discussion of minerals in LDCs, moreover, has obvious implications for MDCs like Canada and Australia. They, too, must face problems about the best utilization of their resources. THE RESTRICTION OF MINERAL TRADE BY DEVELOPED COUNTRIES[a] At least to some extent, the world's leading industrial nations have intervened to control the inflow of minerals. Such regulation is particularly pronounced for energy. Both the United States and western Europe employ

Jan 1, 1976

By Richard A. Busch, Roy L. Soderberg

Large, high, open stopes resulting from vertical crater retreat (VCR) and similar methods are usually filled with sand tailings to support the stope walls and make it possible to mine the pillars. The hydrostatic head resulting from these high stope fills demands extremely heavy bulkheads in the crosscuts to withstand the pres- sure. Occasionally, these bulkheads fail because there are no drains or the installed drains are inadequate. Costly flooding of the mine and loss of life result from these failures. With proper design of blanket drains and filters, the fill can be made failure-proof, requiring only a minimum bulkhead, designed specifically for zero water retention. The effectiveness of the blanket drains can be increased by laying perforated pipes on the bottom of the crosscut within the blanket drain. These drains can have a safety factor of 10 with minimal expense. When the water is properly drained, the hydrostatic pressure on the bulkhead is reduced to zero, leaving only the lateral pressure of the sand. This lateral pressure is partially dissipated by arching and shear against the crosscut walls and consolidation of the tailings as the water is drained. The bulkhead should be placed at least one cross-cut diameter back from the collar of the drawpoint.

Jan 1, 1983