Search Documents

By J. E. Harris

By elimination of other possible nucleation processes, it has been demonstrated, for commercially pure magnesium and a Mg-Al alloy, that at stresses less than that necessary for triple-point cracking creep cavities are most probably nucleated heterogeneously at second-phase particles. Evidence for the existence of such particles is presented and the role of grain boundary sliding in the nucleation process is examined quantitatively. DURING creep deformation of polycrystalline magnesium and its dilute alloys in the temperature range 0.45 to 0.7 Tm (Tm = absolute melting temperature) cavities form mainly along grain boundaries oriented normal to the stress axis and failure eventually occurs by their growth and impingement.' The possibility of low-ductility creep failure of magnesium-alloy reactor cans during service has prompted a number of studies of cavity formation in these materials.2-5 In this paper divergent theories of cavity nucleation6-10 are examined critically and conclusions drawn regarding the most probable mechanism of formation of cavities in magnesium. The paper is divided into two parts. The first section consists of the review and quantitative assessment of the possible role of grain boundary sliding in the nucleation process. In the second part an experimental program is described where an electron-microscope technique has been used to determine if second-phase particles exist in as-received commercially pure magnesium and in a magnesium alloy 1) THEORETICAL REVIEW Possible nucleation sites for creep cavities are: a) high-angle grain boundary triple points,11-14 b) subboundary/grain boundary intersections,15-18 c) ledges in the grain boundary, 19-25 d) second-phase particles. 9,26-30 Each of these possibilities is now considered with special reference to deformation of magnesium. 1.1) Triple-Point Cracking. The stroh31 condition to nucleate fracture is: " > vr [1] where ss = applied shear stress, ? = surface energy, C = shear modulus, L = length of sliding interface. This relationship is independent of the nature of the interface and it is possible to calculate the stress concentration at the end of a sliding high-angle grain boundary and thus deduce, approximately,* the minimum applied stress necessary to nucleate triple-point cracking. Such theoretical predictions for Nimonic alloys have been made by McLean13 and found to agree quite closely with the minimum stress determined by experiment. Stresses capable of nucleating triple-point cracking should also be sufficient to nucleate fracture at a grain boundary due to intragranular slip, for the lengths of sliding interface in the two cases are approximately equal. Thus the minimum stress for triple-point cracking should represent a demarcation between failure due to general "cracking" and that due to cavitation. Hauser, Landon, and Dorn32 have demonstrated that for polycrystalline magnesium in the temperature range 78° to 298°K the fracture stress is inversely proportional to the square root of the mean grain diameter. As pointed out by stroh31 this result indicates that Eq. [I] describes the fracture characteristics of magnesium at low temperatures. Heal3 has reported that for rapid deformation (112 pct hr-1) of polycrystalline magnesium the transition from cracking to cavitation occurs in the temperature range 175" to 275°C. He also presented the fracture-stress values for the same material tested under similar conditions. From Eq. [I] taking G = 1.3 x 10" dynes , ? = 600 ergs . cm-2,33 and L = 0.017 cm, a Stroh-McLean13,31 tensile stress of -266 kg. cm-2 is calculated, corresponding to a transition temperature of -190°C; this is in

Jan 1, 1965

By L. R. Jackson

It is convenient to have a consistent system of notation that will allow the representation of the entire range of complex stresses from hydrostatic compression to hydrostatic tension on plastic flow in a single diagram. Such a system is provided by making use of the fact that any complex stress system can be resolved into a hydrostatic tension or compression and a pure shear. Consider a stress system having the principal stresses This system can be resolved into a new system consisting of the three components and three pure shears. If Sm is positive, the net stress effect is hydrostatic tension; if it is negative, the effect is hydrostatic compression. In order to produce a systematic notation, a quantity that will be referred to as the "triaxial ratio" will be defined by the equation _ Sm Tr = Sm - Sm is given by Eq. I and Sl is the absolute magnitude of the largest principal stress without regard to sign. Table I lists the triaxial ratios for various common systems. Table i.—Triaxid Ratios for Various CommonSyslems Triaxial Ratio Stress System Tr Hydrostatic compression — SI - —St - -S³............................... -1 Torsion or shear -SI - S². S² = O..... O Simple tension SI. SI = SI = 0......... +0.33 Biaxial tension SI = S² S³ - 0......... +0.66 Hydrostatic tension +SI - +S³ = +S³. +1.00 Representation of Strains Strains will be plotted as "true" strains according to the system proposed by Ludwik.1

Jan 1, 1945

By Richard D. Call

Predicting the performance of a waste embankment requires an estimate of the properties of the waste and foundation materials. The performance characteristics and the associated material properties are: [ ] Methods for obtaining estimates of the material properties include: laboratory and field testing, back analysis, and indirect estimates from other material properties. The most critical technical need is the development of indirect methods for use in feasibility studies and mine planning, prior to production when actual samples of waste material are not available. Material properties are not unique, single values; they are probability distributions. There are two components to these distributions: the uncertainties in testing and the inherent variability of the material. The objectives of a material properties evaluation should be to obtain an unbiased estimate of the property distributions rather than the average or the minimum value. Whether the current trend to a probability design analysis is followed or a simple sensitivity analysis is conducted, the unbiased probability distribution is preferable to single values.

Jan 1, 1985

By A. F. Taggart, F. E. Beach

The flotation process for the concentration of ores is a method by means of which one or more of the minerals in the ore (usually the valuable ones) are picked up by means of a liquid film and floated at the surface of a mass of fluid pulp. Here they are separated from the other minerals, which remain immersed in the body of the pulp. In general, the minerals which are floated are sulphides of metallic luster, but some other minerals of metallic luster such as graphite and some sulphides with adamantine luster, such as sphalerite and cinnabar, are amenable to treatment by the process. The importance of flotation lies in the fact that it is primarily a "slimes process" by means of which the particles of valuable mineral, too fine for efficient gravity concentration, are saved with a high percentage of recovery. Recoveries in the mills treating low-grade copper sulphide ores have been advanced 10 to 20 per cent. by the installation of the process and similar increased savings have been accomplished by the same means in mills treating sulphide ores of zinc and lead. When finely ground ore containing sulphides mixed with a siliceous or earthy gangue is brought gently onto the surface of a body of water, in a direction forming an acute angle with the surface of the water, a considerable portion of the sulphide constituent of the ore floats on the surface of the liquid, while the gangue sinks. This is the so-called film flotation, exemplified by the Wood and Macquisten processes. When gas bubbles are introduced into a fluid pulp composed of finely ground ore and water, to which has been added (1) a small amount of certain oils, or (2) a small amount of certain acida or acid salts, or (3) a small amount of certain alkalis or alkaline salts, or (4) a small amount of a mixture of oil with acid or alkali, the sulphide particles in the ore are brought to the surface on the gas bubbles. These collect in a froth

Jan 1, 1917

By H. L. Hollis

The paper read by Mr. George J. Snelus, in 1894, before the Iron and Steel Institute of Great Britain* so fully and ably described the Walrand-Leghisel process that there remains very little to add beyond recording some changes in practice, made since that date, and observed by the writer last summer, at several continental works, and the further fact that the process has now been for some time in successful operation in this country. Briefiy stated, the Walrand-LegBnisel process is an addition to the Bessemer operation, with the object of obtaining quiet and more fluid steel, and consequently sound castings and ingots. This is achieved by adding ferro-silicon at approximately the time of flame-drop in the ordinary Bessemer operation, and making an after-blow. The high calorific power of silicon is well known, and the rapid combustion of it immediately before

Jan 1, 1897

By Alfred R. Powell

FOR the purposes of this discussion, the direct gasification of coal means the of hydrogen and carbon monoxide by the well-known water-gas reaction. Chemicals or other synthetic products may be made from these constituents of the gas and under such circumstances the gas is called synthesis gas. Or, if the same gas is used as a fuel, it is called blue gas or water gas. This type of gas has usually been made from coke, especially in this country, and has been used both for fuel purposes and for manufacture of chemicals. Recently, natural gas has gained the ascendancy as a source of synthesis gas for manufacture of chemicals because of its relative cheapness. As natural gas becomes less readily available and more expensive, coal will take its place as a raw material for the preparation of synthesis gas. This substitution will probably take the form of direct gasification of the coal rather than the present two-step procedure of carbonization of the coal followed by gasification of the coke. The chief reason for this probability is the intensive research now being carried on by several organizations to develop successful and economical processes for the direct gasification of coal, which is a considerably cheaper fuel than coke. In the following pages an attempt has been made to predict the chemicals that will result from this future production of synthesis gas by the direct gasification of coal. CHEMICAL REACTIONS OF SYNTHESIS GAS Given the proper conditions, there are many chemical reactions leading to production of useful products that can be carried out with this mixture of hydrogen and carbon monoxide. These many reactions may be grouped into three classes: (1) interaction of hydrogen and carbon monoxide, possibly with addition of other reactants; (2) reaction of hydrogen with various substances; (3) reaction of carbon monoxide with various substances. Thus sometimes hydrogen and carbon monoxide are utilized together in the same chemical reaction while in other instances only the hydrogen or only the carbon monoxide is required as a reactant. Fortunately, practical methods are available for securing either hydrogen or carbon monoxide from synthesis gas, some of which are also applicable for changing the ratio of these two constituents in the gas when that is desirable.

Jan 1, 1953

By C. E. Mills

STUDIES of ground movement and subsidence resulting from mining operations cover a broad field. It is also a very important consideration and one that eventually affects nearly every mining operation of any extent. The damage to surface buildings, removal of mine surface plants and replacements of main hoisting shafts must reach an astounding expenditure were these cost figures available over a period of years. Were the subject one of mathematical formula and dependent only on the angle of draw of the walls or country rocks, the problem would be relatively simple. Consideration must be given to depth and extent of workings; structural conditions of the orebodies and enclosing country rock; physical properties of these same rocks, including schistosity, bedding, jointing, slips, dikes, faults, and other structural weaknesses. The method of mining, extent of openings, supporting pillars, and amount of moisture or water underground are other pertinent factors. With such a large number of variable factors, it is apparent that the subject of subsidence is one that must be based largely on experience and results at other mines where conditions are somewhat comparable. In presenting this paper, it is the intent to describe the progressive results of past ground movements at the United Verde, to bring out physical conditions largely responsible for this movement, but to refrain from theorizing on the ultimate extent of subsidence resulting from future mining operations.

Jan 1, 1934

By William Glenn

The taking of proper samples of crude ores seems to he less thoroughly understood, or less carefully practiced, than its impor tance requires. We all know how often we encounter the reports of very accurate assays and analyses, the weight of which as evidence wholly depends on the method of obtaining the sample, and is very probably nil, because there has been no proper sampling. Pissages might be cited from technical books, and from current technical literature (all the work of writers whom we delight to honor) to show that even among high scientific authorities there is too little acquaintance with the practical art of the sampler. There is no metallurgical or chemical establishment which does not frequently receive samples truly representing nothing. They consist usually of bits of ore, or what not, selected because they are worse or better than the average of what they are meant to represent. And they are worthless, no matter who made the selection. Where conscious choice is permitted to enter into the operation, a fair sample will not result, unless by a miracle. The work of sampling is often looked upon as within the realm of boys and of pensioners only. At least, though the manual labor be left to subordinates, the principles on which it is conducted and the safeguards with which it is surrounded are not unworthy of the study of experts; and experts should he ready to teach these principles and enforce them in practice. For exact sampling is the indispensable first step towards learning the value of any boxful, carload or shipload of ore. I propose to give a simple account of the method of sampling by hand, such as I have always pursued. There is nothing new about it. So far as I know, it is the immemorial old method, as old at least as Cornish copper-mining. Perhaps my fellow-members in the Institute may suggest improvements in it. If not, it will constitute a record in our Transactions to which laymen and beginners may be referred.

Jan 1, 1892

By Thomas C. Baker

The Fresnillo unit of the Mexican Corporation, S. A., is situated at the old historic mining town of Fresnillo, Zacatecas, Mexico, 33 miles north of the city of Zacatecas and 750 miles south of El Paso, Tex. It is connected with the Mexican Central Railroad by a broad-gage spur 5.5 miles long, belonging to the company. Fresnillo is surrounded by a broad semi-arid valley on the Mexican plateau at an elevation of 7300 ft. The monotony of the valley is broken by a number of low hills. Near the town of Fresnillo is the " Cerro de Proano," an elliptic-shaped hill of gentle slope, rising out of the plain to a height of 325 ft.; the base has a major axis of 4500ft. and a minor axis of 3000 ft. In this hill is the silver-bearing mineralized zone, which comprises past and present mining operations. (In this paper money values are expressed throughout in American currency and the dry short ton of 2000 lb. is used.) The discovery of ore at Fresnillo is credited to the Spaniards, soon after the conquest of Mexico. There are, however, no authentic records to show the amount of work done by them. In 1832, the State of Zacatecas took possession of the property and operated it. Evidently the rich ore above the horizon of the plain had been fairly well exhausted, as an old record states that thirty shafts were used for unwatering, requiring 300 men and 1500 animals. The cost of pumping alone amounted to $150,000 a year. In spite of the fact that cheap convict labor was used, mining costs were reported as $20 and treatment charges as $20 per ton. In 1835, the state was obliged to seek foreign capital, and a company formed in London secured a controlling interest in the property. This new organization sank two shafts, one 11 by 19 ft. and the other 10 by 15 ft., to unwater the mines and extract ore. Large Cornish pumps were purchased in England and hauled overland from Vera Cruz; engines also were installed to operate the arrastres (grinding mills) in the patio process of ore treatment. Substantial buildings were erected and operations were conducted on a large scale, for that period. The patio, the largest in Mexico, was 1150 ft. square. The costs for 1850 were:

Jan 1, 1925

By W. B. Humes

The use of high vacuum on a large industrial scale in the ferrosilicon process for the production of magnesium marks the coming of age of an important new metallurgical technique. The economical production of reactive metals, such as magnesium, which combine with all the well-known furnace atmospheres, has until recently been successfully carried out only by electrolytic methods. It is now apparent that, through the use of high vacuum, the distillation or sublimation of many metals can be done industrially at much lower temperatures, and hence in much simpler equipment, than heretofore has been thought possible. At the beginning of the present emergency, when the ferrosilicon process of producing magnesium was brought to the fore, little was generally known about vacuum engineering, practices, and techniques. In a comparatively short time, the available equipment has been adapted, new equipment designed and built, and a fund of know-how evolved to make possible the production of thousands of pounds of magnesium per day at pressures less than 1/ r0,000 of an atmosphere. Pilot-plant operations have been consistently maintained at pressures even as low 2s one micron (0.001 mm.). These low pressures, which previously were regarded as prohibitively costly or impossible to attain, have been demonstrated as economically feasible on an industrial scale. Necessity for Vacuum The main function of vacuum in the ferrosilicon process, and hence in most vacuum smelting processes, is to lower the temperature at which the metal may be distilled or sublimed from the reduction mixture. A secondary function is to protect the distilled metal from attack by the furnace atmosphere and to permit the formation of a dense condensate. In the ferrosilicon process, magnesium is formed by the reaction between dolomite and ferrosilicon: 2(Mg0-Ca0) -\- HFeSU / t=> aMg + MFe + (CaO)2-SiO2 The metal is distilled from the pelleted charge at a free air pressure of about 0.100 mm. of mercury (100 microns). This low pressure is not needed for the reaction, but rather serves to protect the metal vapor from the oxygen or nitrogen of the atmosphere and permits the formation of a condensate free of pyrophoric material. The reaction proceeds at air pressures as high as several millimeters of mercury, and evidence has been offered to show that the actual equilibrium pressure of magnesium at operating temperatures of 2I50°F. is somewhat higher. Experimentation indicates that the yield begins to decrease at pressures above 500 microns. While no real operating data are yet available on the relationship between

Jan 1, 1944

By John R. Green

ROTARY kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary according to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. MEASUREMENTS OF KILN TEMPERATURE The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records or automatic control are desired, while optical pyrometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. I shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected from puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly 0° to over 200°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without effect of the flame temperature. There should be some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors Influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and comments on the possibility of measurement and control. Of greater number and of varied influence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1941

By Joseph C. Mead, Alan Stanley

The MacIntyre Development of the National Lead Co. is located at Tahawus, N. Y. The operations involve the mining and concentrating of a titaniferous iron ore to produce an ilmenite concentrate and a magnetite concentrate. Construction of the MacIntyre plant was commenced during the summer of 1941,when world conditions threatened to cut off the supply of Indian ilmenite. An open pit mining operation was developed and the crushing and milling equipment put in operation in July 1942. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. The metallurgy of the mill operation was described by Mr. Frank R. Milliken,* Plant Manager, National Lead Company, MacIntyre Development, and presented at the AIME New York Meeting, February 1948. The magnetite concentrate produced in the milling operation was too fine (minus 20 mesh) to be used directly in iron blast furnace operation, and most of the magnetite had to be stockpiled in 1942 and 1943. In 1943, the Defense Plant Corp. built a Greenawalt sintering plant at Tahawus, N. Y., to put the magnetite concentrate in a more suitable form for use in the iron blast furnace. The Greenawalt sintering plant consists of three 10 by 25 ft sintering pans designed to produce 1800 gross tons of sinter per 24 hr. The vacuum to each pan is produced by two Greenawalt fans in series, pulling approximately 30,000 cu ft of air per minute at 50 in. water gauge vacuum. The plant started operation in August 1944. The present plant production averages 25 tons per operating pan hour (approximately 224 lb per operating hour per square foot of grate area) of plus 1 in. sinter. Raw feed to the plant consists of 61 pct magnetite, 4 pct anthracite coal culm, and 35 pct minus 1 in. return fines which are conveyed to a pug mill where the materials are mixed thoroughly and water added to give the mixture 5.5 to 6 pct moisture. The mixed prepared feed is conveyed to two 4 by 10 ft vibrating screens where the minus 1 in. plus 5/8 in. return fines are screened out and discharged into a surge bin for use as a hearth layer. The minus 5/8 in. prepared feed is discharged into another surge bin for use as prepared feed. A charge car, electrically operated, having a capacity of one charge of prepared feed and several charges of hearth layer, lays a thin layer of plus 5/8 in. return fines and 9½ in. depth of prepared feed into the pans. A fluffing roll and a vibrator on the car fluffs and spreads the prepared feed into the pans. An ignition car, electrically operated, ignites the top of the bed with a 30 sec flash burn. The 9½ in. bed sin-ters in approximately 13 min. Dumping the pan, and recharging and igniting the bed requires 2 min. To improve the quality of the ilmenite concentrate produced in the mill and to reduce the amount of titanium dioxide lost in the mill tailings and in the magnetite product, extensive research work and pilot plant operations have been done on grinding the crude ore to minus 65 mesh size (rather than to minus 20 mesh) and concentrating it by a combination of magnetic separation (for magnetite recovery) and flotation (for ilmenite re-covery). These tests have proved successful in increasing ilmenite re-covery and grade. With the development of the ilmenite flotation process to a stage where a full scale flotation plant was in the design stage, the problem arose of handling the 65 mesh magnetite concentrate that would be produced. In order to study and solve the problems of handling and sintering the 65 mesh magnetite in the sinter plant, a pilot sinter plant was secured from John E. Greenawalt. The effect of using 65 mesh magnetite in the sintering operations was then studied on the 2.4 sq ft test pan, operating under conditions as similar to the large plant as could be set up in the laboratory. A series of tests were run in the test pan on present sinter plant feed that had been mixed in the plant pug mill. An average production and an average quality of sinter produced in this series

Jan 1, 1950

By W. E. C. Coxe

Many of you who are interested in the manufacture of iron and steel, have no doubt heard of the "Wheeler process for combining iron and steel." Mr. Wheeler has formed a company, styled the "Combination Trust Company," whose business is to grant licenses for the use of this patent process in producing what he calls "iron-clad steel." It has been proposed to apply it in the manufacture of car or wagon axles, also to shafting, having steel cores or centres covered with iron; to tubes of steel with an inner and outer skin of iron ; to structural purposes, such as girders and beams; bridge and tie-bolts, where the strength of the iron and the rigidity of the steel would be desirable. In answer to a request from Mr. Wheeler, permission mas accorded him to make some experiments at the rolling mill of the Philadelphia and Reading Coal and Iron Company, at Reading, Pennsylvania, with a view to manufacturing some steel-headed rails. In making this kind of a rail two difficulties are encountered. If the iron is brought to the requisite heat to weld properly, the steel is likely to be burned; if the steel is cared for, to prevent burning, the several layers of iron are not brought up to the proper welding heat. Mr. Wheeler claimed that the steel slab covered with iron which he furnished for the head of the rail could net be injured by any heat to which it might be subjected in the ordinary course of heating the rail-pile. He claimed, also, that by this method the porosity, which he thought was characteristic of all solid rails of Bessemer steel, would be overcome. Four steel slabs were furnished for this experiment, being Bessemer steel of .61 carbon, made at the Edgar Thomson Steel Works, and covered with iron in one of the Pittsburgh mills. The slabs were in section seven inches wide by three inches thick, and the iron covering was one-eighth to three-sixteenths inch thick. Each slab was placed on a pile of iron made up in the ordinary way for a rail fifty-six pounds per yard and thirty feet long. The heating was under the personal direction of Mr. Wheeler, and

Jan 1, 1879

By F. R. Archibald, C. M. Nicholson

THE present paper may be considered complementary to an earlier contribution on the same subject by F. R. Archibald and C. F. Jackson.1 It is particularly concerned with engineering and technological aspects of the operations at the Harleyville Alumina Plant during its period of operation from January 1945 to July 1946. The plant was built for and operated by Ancor Corporation, at Harleyville, South Carolina, as part of the government sponsored wartime program related to alumina production from domestic raw materials. The main purpose of the program was to secure technical and engineering data, based on actual plant experience, that might serve as a foundation for large scale production of alumina from raw materials other than bauxite. The Harleyville plant was directed specifically to treatment of clays found in very extensive deposits in the Carolinas and Georgia using the lime-sinter process developed by Ancor Corporation. It is considered that the purpose stated above has been served and this paper is to record and discuss some of the more important findings. The main factor in location of the plant at Harleyville was the presence in that locality of a rather remarkable deposit of high calcium limestone. The clay mining operation was centered near Aiken, S. C., and although a rail haul of ninety miles was involved there were, at the time, factors favorable to the Harleyville location offsetting, in part, the cost of transportation of clay. There are, no doubt, locations in the general area where clay and limestone deposits may be found in closer proximity but they had not been proven up when the project was undertaken. Availability of power from the Santee-Copper development whose high tension line skirted the property; ready access to rail and highway transportation; the promise, realized in actuality, of ample supply of soft water; and availability of labor supply were other factors of importance. Moreover, the general area has the decided advantage, for this type of operation, of a mild climate. Construction was begun in August 1943, and although stopped for a time pending review of the general situation that fall, it was resumed, albeit with less urgency, and substantially completed by the end of 1944. The total capital cost was approximately $3460,000. The first alumina was turned out in April 1945 and from then until the plant was closed down in July 1946, the operations followed a succession of periods of production alternating with periods in which minor alterations were made in conformity with experience. Steady improvement was made and at the time operations were discontinued it was considered that experience and the necessary engineering were in shape for removal of the remaining bottlenecks and a somewhat major revision in one section of the plant. Unfortunately this could not be carried out and it was necessary to discontinue the

Jan 1, 1948

By Archibald Macmartin

THE Königin-Marien-Hütte is the only works in Germany where the Bessemer process is carried on by the direct method. The Besserner plant there, is arranged after the true English type, and the only resemblance to the Swedish mode of procedure is the dispensing with the use of spiegeleisen at the end of the "blow." In a new department of the establishment, started within three years, each of the converters is turned by means of a very neat and compact reversible engine, the steel shaft of which is an endless screw, which turns against the oblique cogs of a large wheel attached to the shaft of the vessel. An advantage which this arrangement possesses over the ordinary English hydraulic arrangement, is the fact that the endless screw suffices to turn the vessel, in either direction, any number of complete revolutions; while even the latest American improvements, so clearly explained to us by Mr. Holley at the opening session of this meeting, do not secure even one complete revolution without changing the angle of inclination of the hydraulic piston. In the endless screw arrangement, there being no limit to the working of the motor in either direction (no return-stroke necessary), the vessel can always, unless outside reasons demand the contrary, be turned around to any desired position by the shortest cut, whether backwards or forwards. Also, the diameter of the cog-wheel attached to the vessel can be made sufficiently great to avoid all unevenness of motion. In the old department the motive-power still continues to be hydraulic. If reports be true, the new department produces spiegelized steel, for the manufacture of all-steel rails. But the old department is still,' as from the beginning, devoted to the production by the direct method of steel for steel-headed rails. The most remarkable fact connected with this direct steel is the ease with which it welds to the iron' of the rail-packets, although no borax or other fluxing agent is used to facilitate the welding. It is very rarely that an exception occurs, and an ingot or a charge is discarded by the rail-mill. The mixture of pig-iron used for the production of this steel is melted in cupolas of very interesting construction (not to be de

Jan 1, 1874

By W. R. Clark, W. W. Cotter

Jan 1, 1946

By W. W. Cotter, W. R. Clark

Jan 1, 1946

By John R. Green

Rotary kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary accorcling to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. Measurements of Kiln Temperature The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records ox automatic control are desired, while Optica1 pyometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. 1 shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected From puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly 0" to over zoo°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without effect of the flame temperature. There should some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and comments on the possibility of measurement and control. Of greater number and of varied influence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1942

By John R. Green

Rotary kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary accorcling to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. Measurements of Kiln Temperature The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records ox automatic control are desired, while Optica1 pyometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. 1 shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected From puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly 0" to over zoo°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without effect of the flame temperature. There should some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and comments on the possibility of measurement and control. Of greater number and of varied influence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1942

By E. S. Greiner

STUDY of the plasticity of germanium or other semiconductor crystals affords unusual opportunities to extend our knowledge of deformation mechanisms. Crystals are available having extraordinary perfection and very high purity. They deform by slip on the systems {111} <110>,1-3 as do crystals of the simple face-centered-cubic structure. Dislocations generated in them during slip are easily revealed in the form of etch pits on either (111) or (100) surfaces.4,5 This fact alone makes possible more detailed studies of mechanisms than is usually the case with metals but, even further, the effect of deformation on their electrical conductivity is very large compared with metals. This comes about not only because the mobility of the charge carriers is reduced, as in deformed metals, but also because the number of these carriers is greatly altered. This latter effect seems closely related to the formation of both line and point imperfections during deformation and thus provides a needed tool for the study of the kinds and distributions of these imperfections. Other investigators have deformed germanium at elevated temperatures by bending,1, 6-8 compres-sion,6, 0,10 tension,2,3,6,11,12 torsion,23 and indentation." Wang and Alexander" have also reported successful indentation at room temperature. Dislocation etch pits consequent to deformation have been observed and studied.7,8,10,18,14,20 The experiments to be de- scribed here include principally the compression and the subsequent annealing of germanium with concomitant studies of etch pits, microstructures, and electrical properties. Both single crystals and heavily twinned specimens were used. Some indentation studies are included. Experimental Methods Plastic compression was effected in the apparatus shown schematically in Fig. 1. It consists of two tantalum platens contained in a helium atmosphere and so arranged that pressure can be applied by a hydraulic press. The specimen between the platens is heated by the surrounding furnace. The specimen is usually a small crystal cube about 0.30 in. on an edge. A control specimen is always inserted so, that it is subject to the same thermal cycle as the one being deformed. This serves to detect any impurity contamination that might accompany the thermal treatment. For high temperature work, where such impurity contamination often occurs, the specimens were first plated with gold whenever subsequent electrical properties were to be determined. This method" is effective in preventing significant contamination of germanium up to temperatures at least as high as 750°C, as evidenced by the constancy of the electrical conductivities of control specimens subjected to the same heat treatments. The total range of temperature used for deformation was from 375°C, the lowest at which significant flow was observed, up to 900°C. Microscopic examination was made after mechanical and chemical polishing and etching. Dislocation pits were revealed with CP-4 etchant by the tech-

Jan 1, 1958