Search Documents

By M. Cross

INTRODUCTION The development of refining processes involving gas injection into liquid metals has seen the evolution of a variety of designs [I]. During the last few years or so the top, bottom and side blown processes have, essentially, been combined to produce a series of mixed gas blowing schemes (eg. the LBE [2,3] and LD-OB processes [4,5]). Although, a variety of mixed gas blowing processes have been carefully engineered and recorded operational experience now attests to their effectiveness, optimising their design and operational performance is another matter. Detailed process analysis of such operations is impeded by the complex nature of the physical and chemical processes involved: . fluid flow behaviour of the liquid metal and injected gases, . chemical reactions in the vessel, . mass and heat transfer within the fluid phases in the vessel, . influence of the geometry (eg. location of the tuyeres, etc.), . monitoring the operational performance. By and large, design and operating parameters evolve from a combination of laboratory scale experiments, pilot plant work and, of course, practical engineering experience. Conventionally, the gas-liquid system used to model the industrial process is air-water, for a number of valid reasons including – . visual demonstration plus geometric and (to some extent) dynamic similarity, . the fact that the system demonstrates, at least, qualitatively many of the complex features of gas injection - interaction between the gas and the liquid - the nature of the gas flow behaviour - qualitative indications of mass transfer rates Important experimental contributions to the understanding of gas liquid systems include the work of Brimacombe [6], Wraith [7], T.Robertson [8], D.Robertson [9], Guthrie [10] and Szekely [11] (these references provide starting points to identify the major published work in this area). Although air-water systems have been instrumental in providing a great deal of qualitative insight into the fluid flow behaviour of the processes, reliable quantitative predictions are more problematic. A number of workers (notably Brimacombe and colleagues [6, 12])have demonstrated that different gas-liquid systems can lead to wide variations in behaviour. Other limitations of physical modelling include the assumptions of isothermal flow, scale- up of turbulent flow behaviour and the inability to directly include the effects of chemical reactions. The above limitations in physical modelling, therefore, yield a natural role for mathematical modelling provided that it can be made comprehensive enough whilst remaining cost-effective. The major physical processes involved in gas injection systems may be summarised as . behaviour of the gas envelope structure in moving through the liquid metal . the global movement of the liquid metal . momentum interaction between the liquid metal and the injected gas . heat transfer and mass exchange via the chemical react ions. The behaviour of gas envelopes forming at a tuyere and then moving through the liquid has been investigated thoroughly by a large number of workers. Such models are generally based upon simple physic- al concepts derived from visual observation. An early model by Davidson and Schuler (DS), based upon a force balance between the liquid inertia and a combination of the bouyancy and momentum forces on the envelope, has proved to be a useful tool in predicting bubble volumes at detachment [13]. The DS model has been successfully modified in a number of ways [14-17] to cope with heat transfer and reactive transfer rates, etc. Furthermore, the basic ideas summarised above have also been confirmed on industrial converters by both Guthrie [I8] and Brimacombe [19]. Models have also been developed to predict the behaviour of the "chemical" component of some gas-liquid systems. However, one thing is clear; all gas-liquid reactive systems are governed by the degree to which effective mixing occurs. As such, the processes are dominated by the behaviour of the heat and mass exchange of the two phase fluid flow system. It is the pattern of movement of the turbulent liquid metal plus its interaction with the injected gas which must be predicted reliably, if sufficiently comprehensive comp-

Jan 1, 1984

By J. D. Alexander, W. L. Martin, J. N. Dew

This paper presents data obtained using a flood-pot technique to determine the fuel available and the corresponding theoretical air requirements for in situ combustion of crude oils. Since the technique is relatively quick and easy, it is a practical and convenient tool for evaluating reservoirs as fireflood prospects. It is also a research tool which facilitates systematic study of the variables affecting fuel availability and corresponding air requirements. The understanding of these variables is of prime importance to those concerned with the technical and economic development of in situ combustion as an oil-recovery process. The experimental results show conclusively that the fuel available for in situ combustion is not a constant but, rather, varies with crude-oil characteristics, porous-medium type, oil saturation, air flux and time-temperature relationships. Thus, the fuel availability for specified field applications should be determined using actual reservoir crude and core material and the process conditions expected during in situ combustion in the reservoir. INTRODUCTION In situ combustion is a thermal process for recovering crude oil from reservoirs. The thermal energy released during the combustion of a small amount of the oil in place aids in the displacement of the remaining oil. Numerous articles have been published describing the in situ combustion process giving detailed results of laboratory and field experiments.10 In order to engineer an in situ combustion project, a number of important factors must be considered and determined. These factors include: (1) the amount of fuel consumed per unit of reservoir volume swept by the combustion zone, (2) the composition of the fuel consumed, (3) the amount of air required to consume this fuel, (4) the portion of the reservoir swept by the combustion zone, (5) the appropriate air-injection rates and pressures, (6) the amount of oil that will be recovered, (7) the rate of oil production and (8) the operating costs. Nelson and McNiell1 recently have described a procedure which utilizes laboratory combustion-tube data as a basis for the calculation of some of these design factors. Various authors have attempted to describe the in situ combustion process mathematically, and considerable progress has been made. Analytical solutions to the problem of heat transfer from a moving combustion front have been obtained for linear and radial systems."-' All of the published results involve the assumptions that: (1) fuel concentration is constant throughout the reservoir, or that fuel concentration is inversely proportional to the velocity of the front for a given rate of oxygen consumption; and (2) the fuel reacts instantaneously with injected oxygen, while liberating a constant amount of heat per unit weight of fuel at all temperatures. It seems both desirable and reasonable to test the validity of these assumptions experimentally. This paper presents laboratory data which were obtained by means of a "fire flood-pot" method for determining fuel availability and composition, and the corresponding theoretical air requirements for in situ combustion of crude oils under variable conditions. The mechanics of the method are similar to a conventional tube-run experiment.' The important differences involve the size of the reservoir model used and the method for providing the experimental environment. The new method subjects conventionally-sized core samples or unconsolidated sands to a programmed environmental sequence similar to that experienced by a similar volume of rock during the approach and passage of a combustion front in a long tube or in an oil reservoir undergoing in situ combustion. Restored-state samples can also be used. The small samples and relatively simple techniques involved allow an experiment to be set up, run and calculated in about three 8-hour days. This is a considerable improvement over long-combustion-tube techniques which can require several days to run and several more work days to set up and calculate. All the runs presented were run at 40-psig injection pressure. Pressure was not considered as a variable for these experiments, since we previously had found that it had only a small effect on fuel availability up to 600 psig.APPARATUS AND MATERIALS APPARATUS The fire flood-pot apparatus consists of a consolidated

By Gerhard Derge

EXTRUSION processes are used in the commercial production of a wide variety of products, as indicated by the review presented a few years ago by D. K. Crampton.1 Most writers have confined themselves to a general description of the equipment and products and the engineer-ing aspects of the process. The few studies that have dealt with the metallurgical side of extrusion have been concerned primarily with an examination of the mode of flow of the metal during extrusion. This has been accomplished by the use of composite billets, by scribing grids on symmetrical sections of billets and observing the change of dimensions in the gridwork, or by examining microstructures in extruded sections.2-8 Another limitation of these original studies is that they were confined to the extrusion of very simple shapes, usually rods having a diameter of about one-fourth that of the billet. Tin is particularly well suited to the extrusion of collapsible tubes and similar shapes in which the extruded section is very small in comparison to the diameter of the billet or slug. In modern production, impact extrusion methods are generally employed, therefore the thickness of the slug is small compared to its diameter. Under these conditions the process differs considerably from the processes that have been most fully described in the literature, and it is known that the quality of the product is very sensitive to slight variations in any one of the many variable factors involved, such as composition and structure of the alloy, rate of extrusion, temperature, shape of punch and die. An exhaustive examination of all of the above-mentioned problems promises to produce so many data that it seems advisable to initiate the reports at this time, even though all of the factors outlined have not been examined fully, and to confine this paper to a description of the apparatus and method. Only tin and its alloys with small amounts of copper have been considered. These are the alloys most commonly used in this country for the production of the type of articles already described.

Jan 1, 1939

By Bradley Stoughton

As a part of the systematic study of the alloys of iron under the auspices of the Engineering Foundation, and preliminary to the commencement of comprehensive work on this larger subject, the authors have undertaken an investigation of the available literature dealing: with the alloys of iron and silicon. The purpose is to collect all the data in English and foreign languages and present them in two mono-graphs, one of a more scientific and the second of a more industrially useful nature. Of course, a great deal of information upon the constitution of the iron-silicon alloys was found specificially upon the changes of phase in the equilibrium diagram and the different phases present, such as solid solution, chemical compounds (iron silicides), etc. While no extended research was contemplated in the particular study undertaken, nevertheless the data collected proved to be so contradictory in many respects that a simple study of some of the outstanding problems involved in the constitution and equilibrium diagram was undertaken Because research was not a primary object of the work, and also because of the extreme industrial importance of the silicon alloys between 0.80 and 14 per cent. silicon, and finally because of the unsatisfactory state of knowledge existing as to these alloys, the experimental investigation was limited entirely to alloys with less than 10 per cent. silicon.

Jan 1, 1930

By Alfred Boyles

"HEREDITY"' in cast iron has been a subject of much discussion. Numerous experimenters have found that the properties of gray iron may vary greatly without corresponding variations in composition or thermal treatment. The main structural difference in such cases is in the size and distribution of the graphite flakes and the explanations given usually attribute this difference to some chemical element not shown by ordinary analysis or to some physical factor, such as inclusions in the melt. It cannot be said that any of these theories is completely satisfactory. Much remains to be learned about cast iron and for this reason a study of the material was undertaken as a part of the program of fundamental research at Battelle Memorial Institute. A review of the literature indicated that very little systematic work had been done on the mecha-nism of freezing in cast iron. The experiments described below are largely concerned with that problem.

Jan 1, 1937

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of April, 1913: BARNES, BLAKESLEE, Min. Engr Burrwood, La. BOYLSTON, HERBERT M., Cons. Met. Engr 26 Abbot Bldg., Cambridge, Mass. BUEHLER, HENRY A., State Geol Rolla, Mo. CASTO, WILLIAM H., JR., Mining Bonanza, Idaho. COHEN, MAXWELL B., Mill Operator Miami, Ariz. EVANS, MILTON R., Shop Draftsman 92 Division St., Kingston, Pa. HARPER, WALTER S., Asst. Treas 42 Broadway, New York, N. Y. JAMES. JAMES S.. Min. Engr Telluride. Colo.

Jan 5, 1913

By D. M. James, J. C. Martin

The results are presented of a study of the application of analytical methods to the solution of two-phase flow into single wells. Approximate analytical expressions for the pressure distribution in two-phase flow are found ;;; a number of conditions. The results obtained from the analytical solutions me found to be in good agreement with results obtained by finite difference techniques using a high speed digital computer. Mathematical solutions for four sets of boundary conditions are presented. All of these solutions are composed of a short-term transient plus a steady or quasi-steady state. The rates of decay of the short-lived transients are analyzed. It is found that the durations of the short-term transients may be characterized by a parameter defined as the time constant which can be determined from simple relations. It is shown also that if the outer radius is much greater than the radius of the well. the short term transients decay at rates which are proportional to the square of the exterior radius, and the rates of decay are only slightly dependent upon the radius ratio. Numerical solutions based on finite difference techniques are presented for a number of conditions. The numerical solutions are in good agreement with the predictions based on the theoretical analysis for small and moderate drawdowns. Examples involving large drawdowns indicate that the nonlinearities in the equations of flow do not appreciably alter the longevity of the short-term transients. In all cases the time required for the short-tern transients to disappear is predicted satisfactorily. INTRODUCTION The mechanism by which oil and gas flow into a single well is of vital interest to the petroleum industry. The fundamental equations of two-phase flow which describe this mechanism are nonlinear partial differential equations. Numerical solutions of these equations describing pressure transients have been obtained with the aid of electronic computers. Although solutions obtained in this manner take into account a large number of effects, the reduction of this information to useful generalities is difficult. One method of obtaining generalities is the use of linearized approximations of the nonlinear equations. Since it is possible to obtain explicit solutions of the linearized equation, general properties of the role of pressure in the flow mechanism may be ascertained. Results obtained from this approach are limited to some extent by the linearizing assumptions. The severity of these limitations may be evaluated by comparing solutions of the linear equation with numerical solutions of the more exact nonlinear equations of two-phase flow. In the past considerable amount of work has been devoted to studying pressure build-up using the single-phase flow theory. Unfortunate1y, most prep sure build-up tests involve multiphase flow. A small amount of work has been done studying pressure build-up where the flow is two-phase. The encouraging results of these studies suggest that useful results may be found from additional studies of not only pressure build-up, but also the rapid transients associated with placing a well on production. This paper presents the basic theory of the pressure transients associated with placing a well on production and with closing it in. The paper is concerned chiefly with two-phase compressible flow; however, the results also apply to single-phase flow. The results are based on analytical solutions of the flow equations, and they are verified by numerical solutions using finite difference techniques. Much of the previous work on compressible flow into wells has been confined to single-phase flow. Some work has been done on compressible two-phase steady state flow, and solutions of the equations of flow have been found by finite difference techniques using high-speed computers. Muskat1 presents some rather general solutions to the equations of single-phase compressible flow into wells. Much work has been done on pressure build-up in wells (see, for example, Refs. 2-6). Almost all of the work on pressure build-up concerns single-phase flow with the exception of Ref. 5 and part of Ref. 2. Some work has been done on pressure fall-off in injection wells.718 Muskat9 presents the solution of the equations for radial steady state two-phase compressible flow. Handyl0 extends Muskat's solution to obtain

By James Aston

INDICATIVE of the practical importance of the achievement of James Aston , recipient of the Robert W. Hunt Medal for 1930, is the following prosaic item from the financial columns of a recent issue of a New York newspaper. "According to private advices from Pittsburgh, production costs of the A. M. Byers Co. for 1929 were reduced about $5 a ton by the use of the Aston process for making wrought iron pipe. A greater saving is anticipated for 1930, when more of the company?s requirements will be produced by the new method."

Jan 1, 1930

By A. B. Parsons

AT the outset, the authors of this paper desire to file a disclaimer and an, explanation. They have no inside information from occult sources; neither of them feigns clairvoyant powers in the slightest degree. It is true that they have indicated on be graphs an approximate trend for the consumption of seven important mineral commodities up to the year 1954. At best this is a risky business; the figures do not pretend to be any- thing more than reasoned conjectures that are predicated on an attempt to evaluate some of the more obvious of the many factors that are likely to have a bearing on the future.

Jan 1, 1937

By W. O. Philbrook, H. E. Burner, F. S. Manning

The equation of continuity for the hydrogen reduction of hematite in a fixed bed of closely-sized particles is solved assuming a flat velocity profile, negligible temperature gradients, md negligible axial diffusion. A kinetic expression from the literature is used which assumes the reduction process is controlled at the oxide-metal interface. The integral fractional conversion is computed, and the importance of particle diameter, flow mte, temperature, bulk axial diffusion, and inter- and intra-particle mass trarnsfer is predicted. Comparison with experimental data suggests one or more additional undefined variable(s) is significant. Equipment modifications are suggested for fidture experimentcll work. WITH the increasing desire to "design" the ore feed of a blast furnace, it has become necessary to define more quantitatively the process variables and to evaluate the extent of their control upon the reduction process. The bulk of the work reported in the literature has centered about the reduction of single particles; however, the blast furnace process more closely resembles reduction of a fixed bed than that of single particles. To simplify this analysis, the isothermal reduction by hydrogen of a natural hematite in a fixed bed of closely-sized particles is examined. With appropriate modifications in the kinetic and flow rate expressions, the approach employed should be extensible to mixtures of carbon monoxide, hydrogen, and inert nitrogen, and to adi-abatic conditions, thus approaching the blast furnace process more closely. The fixed bed variables which are investigated in this study are particle diameter, flow rate, temperature, and bulk axial diffusion, as well as inter-and intra-particle mass transfer. Of particular interest is the effect of particle size upon fractional conversion for a bed operating under constant pressure drop. The constant pressure drop concept bears a close resemblance to the blast furnace process, where regions of larger particles may provide a greater permeability to divert most of the reducing gas flow from the regions of smaller ore particles. Under such conditions one would expect qualitatively that, for sufficiently small particle sizes where the flow rate is small and the total surface area is large, the reduction rate would be limited by the gas flow rate. Initially the gas entering the bed reacts very rapidly and the composition approaches the equilibrium conversion value a short distance from the reactor inlet. This concentration "wave-front" then moves up the bed as the flow of reducing gas is continued, leaving in its wake an ever increasing layer of reduced particles. Providing that the reducing gas leaves the bed at equilibrium concentrations, conversion is expected to increase with an increase in flow rate, and hence with an increase in particle diemater. Conversely, for sufficiently large particles the flow rate will be high but the surface area available for reaction will limit the reduction rate. Since the total surface area decreases with an increase in particle size, conversion, in this case, is expected to decrease as the particle diameter is increased. It is clear then that between these two extremes an optimum particle diameter must exist. THEORETICAL DEVELOPMENT Above the temperature where wiistite is stable (about 560°C) the reduction of hematite proceeds through the series Fe2O3/Fe3O4/FeO/Fe. On the basis of microstructural studies and earlier work, Edström1 has postulated a mechanism for the reduction of an ideal hematite lattice: 1) Iron phase formation at the boundary between wiistite, iron, and gas (for sufficiently porous iron). 2) Diffusion of iron across a wustite layer. 3) Phase boundary reaction of Fe3O4 to FeO. 4) Diffusion across a dense magnetite layer. 5) Phase-boundary reaction of Fe2O3 to Fe3O4. According to the mechanism postulated, gaseous reaction product has to be removed only at the boundaries between wüstite and iron or gas, the only possible exception being enveloped Fe3O4 specks. On this basis McKewan2,3 has proposed that one may consider the hematite reduction process as a simple two-phase system of oxide/metal. If, for FeO and Fe3O4 layers of negligible thickness, the hypothesis is made that the rate of formation of a

Jan 1, 1963

71 BROADWAY, NEW YORK, Sept. 22, 1913. CHARLES W. GOODALE, Chairman, . DARSIE C. BARD, ESQ., Secretary. Committee on Precious and Base Metals, Butte, Montana. Gentlemen The wonderful success of the meeting of the Institute held in Montana makes it necessary that some public acknowledgment should be made to those to whom this success is due. We are conscious that the securing of the great number of technical papers of lasting value and the carrying to success of most complete detailed arrangements for holding the meeting have called for several months of skilled effort on your part. The benefit of the meeting is very great and extends not only to those who were fortunate enough to be present, but to our four thousand absent members and their friends as well. To you and your associates on the Committee whose efforts have made this never-to-be-forgotten meeting possible we owe far more than can be expressed in votes of thanks. Very respectfully, CHARLES F. RAND, President.

Jan 10, 1913

By PAUL DYER MERICA

PAUL DYER MERICA, who has been awarded the James Douglas Gold Medal for his achievements in non-ferrous metallurgy, is a Hoosier, having been born at Warsaw, Ind., in 1889. His father, a clergyman and educator, was president of the University of Wyoming from 1908 to 1913. After graduating from the University of Wisconsin in 1908, young Merica (not yet twenty years of age) went to China, where he was professor of chemistry in Chekiang Provincial College, Hangchow, until 1911. He then went to Germany to s t u d y and was fortunate enough to receive his Ph.D. from the University of Berlin just a few months before the outbreak of the World War in 1914. Returning to America, his first position was as special investigator at the En¬gineering Experiment Station of the University of Illinois, but before the year was out he joined the staff of the U. S. Bureau of Standards as associate physicist. Since 1918, he has been superintendent of research for the International Nickel Co. His work during those years is excellently summarized in the following quotation from the statement of Zay Jeffries recommending him for the award.

Jan 1, 1929

By Y. Shimomura, M. Serizawa, Y. Takahashi, K. Miyagawa

The "semi-pellet" sintering method developed and currently being used at the Fuji Iron & Steel's Hirohata Works is discusssd. It is shown that the method makes fine-sized material easily sinterable and increases sinter production. The operation can be incorporated readily into conventional sintering plants. Sintering plant raw materials currently being used in the Hirohata Works consist of 40 pct pyrite cinder, 40 pct fines resulting from crushing and screening of imported ores, and 20 pct others, such as mill scale and iron sands. Pyrite cinder, a major component in the sinter feed, has been getting finer since 1952, due to the increased grinding required for the improvement of the results in the iron sulfide flotation and to the adoption of FluoSolid roasters in sul-furic acid plants; some fines pass 100-mesh sieve almost completely. Increased use of the fine-sized pyrite cinders in the sinter raw mix resulted in such difficulties as decreased bed permeability, uneven firing conditions, and low yield. In an attempt to study the cause and to find a remedy for this problem, a series of experiments were made, using an 80-kg experimental sintering pan. As a result it was established that, by rolling the fine-sized pyrite cinders into small balls of 10 to 3 mm diam (hereafter called semi-pellets) and mixing them into the sinter raw mix, the bed permeability was improved, the sintering time shortened, and the yield and production rate increased. It is proposed that this new method be called the semi-pellet sintem'ng. In recent years the pelletizing process has taken the spotlight in the agglomeration field for treating fine-sized ores here in Japan as well as in the U.S. and Europe. This process produces pellets suitable for the blast furnace charge as such, and consists of three major operations: fine grinding, balling, and firing. With regard to the firing technique, some problems still appear unsolved. In the semi-pellet sintering, however, several ad- vantages can be claimed: the balling operation is relatively simple because only small-sized balls are shown to be acceptable and the operation can be readily incorporated into the conventional sintering plant, since only balling, not grinding or firing, equipment is needed. Basic test work on the process was initiated in 1954 and favorable results were obtained. Accordingly a pilot plant was built in 1955 and the test work was continued. The semi-pellets thus prepared in the pilot plant were tested further by USing them in the actual sintering pan and their beneficial effects ascertained. In late 1956 a drum-type balling machine (2.4X4 m) was installed and it went into operation in April 1957 in conjunction with the Greenawalt sintering plant (8 pans having dimensions of 7.2 m in length, 3 m in width, and 0.3 m in depth). In October 1958 a cone-type pelletizer, with a 2.2 m diam, and later a disk-type pelletizer were further added in the plant. In the DL sintering plant (2000 tpd), newly built in July, 1960, four disk-type pelletizers (3.2 m diam, 10 tph capacity) were installed. By mixing the semi-pellets thus prepared with the feed, the sintering operation was found to be greatly improved. The results of the basic test work, and the equipment and operation of the semi-pellet sintering operation at the Hirohata Works will be described. ON THE SINTERING CHARACTERISTICS OF FINE SIZED PYRITE CINDERS To ascertain the effect of addition of fine-sized pyrite cinders on the sintering characteristics, a series of measurements on bed permeability was carried out by varying the size distribution of pyrite cinders. The composition of the raw mix used in the tests was fixed at 50 pct pyrite cinder, 20 pct Larap magnetite fines, 30 pct sinter return, and 5 pct coke; only the size distribution of the pyrite cinder was varied. Also the moisture content was changed at each size distribution. The results are given in Fig. 1. For all pyrite cinders tested the bed

Jan 1, 1961

By T. C. Boberg, R. B. Lantz

This paper presents a method for calculating the producing rate of a well as a function of time following steam stimulation. The calculations have proved valuable in both selecting wells for stimulation and in determining optimum treatment sizes. The heat transfer model accounts for cooling of the oil sand by both vertical and radial conduction. Heat losses for any number of productive sands separated by unproductive rock are calculated for the injection. shut-in and production phases of the cycle. The oil rate increase caused by viscosity reduction due to heating is calculated by steady-state radial flow equations. The response of successive cycles of steam injection can also be calculated with this method. Excellent agreement is shown between calculated and actual field results. Also included are the results of several reservoir and process variable studies. The method is best suited for wells producing from a multiplicity of thin sands where the bulk of the stimulated production comes from the unheated reservoir. The flow equations used neglect gravity drainage and saturation changes within the heated region. INTRODUCTION This paper presents a calculation method which can be used to predict the field performance of the cyclic steam stimulation process. The calculation method enables the engineer to select reservoirs that have favorable characteristics for steam stimulation and permits him to determine how much steam must be injected to achieve favorable stimulation. While the calculation represents a considerable simplification of physical reality and the results are subject to numerous assumptions which must be made about the reservoir, it has been found that realistic calculations can be made of individual well performance following steam injection. The duration of the stimulation effect will depend primarily on the rate at which the heated oil sand cools which, in turn, is determined by the rate at which energy is removed from the formation with the produced fluids and conducted from the heated oil sand to unproductive rock. A complete mathematical solution to this problem is a formidable task, and finite difference techniques would undoubtedly have to be used. The calculation method pre- sented here utilizes analytic solutions of simple related heat transfer and fluid flow problems. The method is sufficiently simplified that it can be used as a hand calculation, although the calculations are somewhat lengthy and laborious. For that reason, the analysis was programmed for an IBM 7044 digital computer. Well responses observed at the Quiriquire field in eastern Venezuela&apos; have been matched using this program after making suitable approximations for reservoir and wellbore conditions. One of the most valuable uses of this calculation method is to assess the effect of reservoir and proc-cess variables on the stimulation response. This paper contains results of several studies made of key reservoir and process parameters. Among the most important of these is the influence of prior wellbore permeability damage. If a well is severely damaged prior to stimulation, a higher stimulation response will be observed than if it is undamaged. If a portion of this damage is removed, a permanent rate improvement will occur. THEORY I)ES(:KJJ&apos;TION OF CALCULATION METHOD The process of cyclic steam stimulation is essentially one of reducing oil viscosity around the wellbore by heating for a limited distance out into the formation through the injection of steam. Suitable modifications of the calculation technique presented here can be made so that stimulation of wells by hot gas injection or in situ combustion can also be calculated. A schematic drawing of the heat transfer and fluid flow considerations included in the calculation method is shown in Fig. 1. In brief, the calculation assumes that the oil sand is uniformly and radially invaded by injected steam. For wells producing from several sands, each sand is assumed to be invaded to the same distance radially. In calculating the radius heated rn energy losses from the wellbore and conduction to impermeable rock adjacent to the producing sands are taken into account. After steam injection is stopped, heat conduction continues and oil sands with r < ra cool as previously unheated shale and oil sand at r > r, begin to warm. The effect of warming of oil sand out beyond r, has little effect on the oil production rate compared to the effect of cooling of the oil sand nearer the wellbore than ra. Thus, in computing the oil production rate, an idealized step function temperature distribution in the reservoir is assumed where the original temperature exists for r > rn and where an average elevated temperature exists for r < rn. The average temperature in the oil sand for the region r < rn is computed as a function of

Jan 1, 1967

By John M. Cummings, Warren. Harry V.

THE Geology Department of the University of British Columbia has undertaken the task of examining the ores from as many as possible of the gold mines of British Columbia. The object of this work is two- fold. First, it is known that detailed mineralographic studies are useful in attacking ore-dressing problems, and these studies are intended to be helpful to mill operators. Second, it is hoped that mineralogical and mineralographical studies will prove useful adjuncts to those of lithology and structure in throwing more light on problems related to the origin of the deposits. The paper shows that gold, for all practical purposes, is not present in an ore mineral in solid solution nor as a eutectic with any mineral; if the latter were true the gold particles would be distributed equally throughout that mineral. The gold occurs either as native gold or as a gold-silver telluride and is not distributed regularly through any mineral or minerals. The relationship between the gold or gold-bearing telluride and the associated minerals affords a means of classification that is not only simple but also appears to be directly related to the geological nature of the deposit, which may be summarized as follows: 1. Disseminated Gold Type.-Precious minerals in extremely small grains, which are distributed without regard to grain size, fractures or grain boundaries: (1) Hedley variety-gold in native form; (2) Surf Point variety-gold predominantly as telluride. 2. Veining Gold Type.-Precious minerals in grains of various sizes, which occur mainly along fractures and grain boundaries: (1) Cariboo gold quartz-goldin native form. (2) Waneta variety-gold as telluride. Application Te Ore Dressing These mineralographic studies have proved to be of value to mill operators, and future studies of a similar nature should prove increasingly useful because every year provides a further opportunity to correlate

Jan 1, 1937

By AIME AIME

FEW mining schools possess an art gallery and certainly none can equal the collection of paintings depicting the mineral industries now hanging in the comparatively new building of the School of Mineral Industries at The Pennsylvania State College. Dean Steidle, who conceived the idea, early this spring boasted of 55 paintings in the collection, by 24 different artists, the gallery being appraised at $18,000. Since then, eleven additional paintings have been added. Opportunity will he presented for an inspection at the meeting of the Industrial Minerals Division, to be held at the College, Sept. 24-26.

Jan 1, 1936

By E. O. Wagner, V. F. Parry, W. S. Landers

Development work has shown that the yield of primary tar from coal is proportional to the heat in the volatile matter of the coal and that the yield of tar from noncoking coals may vary from 10 to 45 gal per ton on the ash-free and moisture-free basis. Pilot plant operations have proved that 100 to 135 pct of the bench-scale carbonization-assay yield of tar can be obtained. FOLLOWING investigations by the Denver Bureau of Mines on drying fine coal in the entrained state,&apos;. &apos; Texas Power & Light Co. employed the fluidized technique to upgrade Texas lignite for use in power plants. Because of the rapidly rising cost of natural gas in Texas the company agreed to cooperate with the Bureau of Mines in studying further the upgrading of lignite by low-temperature carbonization, since potential value of the tar would help offset the cost of fuel. Considerable interest was aroused, therefore, when Aluminum Co. of America decided to use dried lignite in its 240,000-kw power plant at Rockdale, Texas, operated by Texas Power & Light. Carbonization of coal before burning in a power plant is not new. Plants in Germany have been operated for many years on carbonized brown coal and lignite briquets produced in large integrated plants. Large-scale experiments in carbonizing pulverized coal with hot flue gases were made 30 years ago at Milwaukee," and many inventors have proposed other processes. In the U. S., technical and economic problems have prevented successful operation of large plants on carbonized coal. but new techniques of handling solids in fluidized beds may overcome these difficulties, particularly if the higher volatile noncoking coals are used. Any bituminous material will decompose when heated to about 900°F to yield primary tar, gas, and char. The quantity of tar obtained from various coals depends on their rank and volatile content and to some extent on rate and method of heating. The liquid products derived from thermal decomposition of peat, brown coal. lignites, oil shale, and noncoking bituminous coals can be easily liberated by rapidly heating these materials in a fluidized bed at about 500°C (932°F). Since it takes only a few minutes to heat small particles of fuel to carbonizing temperature in a fluidized bed, processing plants can be built to handle up to 50 tph at relatively low cost. The pioneering development work being conducted at Rockdale, Texas, by Alcoa and Texas Power & Light will solve many engineering problems of such operations. The Bureau of Mines at Denver has studied the carbonizing properties of several hundred coals by small scale assay at 500°C, deriving a simple correlation between the potential yield of tar and the proximate analysis. This correlation, shown in Fig. 1, compares the heat in the volatile matter of the coal with the potential yield of primary tar. The yield of primary tar varies from 12 to 50 gal per ton of pure coal." About the same amount of heat is needed to * MAF equals moisture-and-ash-free basis. distil any dry coal at 500°C, and the time required to carbonize a given particle size is about the same for any coal. It is therefore obvious that coals rich in volatile matter will show the greatest profits when processed. Texas lignites are rich in volatile matter, which contributes some 5700 Btu per lb of MAF coal, and the potential primary tar and oil yield from this lignite averages 12 pct by weight or 27 gal per ton from the pure lignite. Texas lignites are considerably richer in potential tar than lignites of North Dakota and Montana. During 1950 the Bureau of Mines conducted many experiments on carbonizing fine dry coal in the entrained state, publishing a report4 n major features of pilot and commercial-size units required to carry out the process. Additional experimental work has been done at Denver and the pilot plant has been improved, particularly the facilities for studying removal of fine dusts from tar vapors and gases at high temperatures by electrostatic precipitation. A number of materials have been carbonized, including sawdust, peat, brown coal, Brazilian oil shale, lignites, and the lower rank bituminous coals having noncoking properties. Straight coking coals cannot

Jan 1, 1957

By R. B. Schluter, M. M. Fine

Processes for manufacturing prereduced pellets have heretofore required temperatures of 2100°F or higher. Sulfides will accelerate the liquid-phase sintering of metallic iron, yet do not deter the reduction of iron oxides. The sulfides may be introduced as gases to the kiln atmosphere or as solids in the re-ductants. The net result is that well metallized iron pellets with good crushing strength can now be produced at a little over 1800°F. One of the most persistent topics at technical gatherings and in the recent scientific press has been the reduction of iron ore. In May 1960, a symposium on the subject was sponsored by the Electrochemical Society. The proceedings, comprising two dozen papers, were later published.&apos; More recently, in November 1966, a similar gathering took place at Michigan Technological University, Houghton, Mich. The latest meeting was the International Congress on Production and Utilization of Reduced Materials at Evian, France, in May 1967. If the volume of literature, symposia and conferences is a measure of industry concern, then the current interest in reduction must be at a high level. Barrett,2 one of the early pioneers, stated some years ago that "The history of sponge iron has been so discouraging that many men in the iron and steel industry are violently opposed to giving it any further consideration." In spite of the "violent opposition" noted by Barrett, research people in and out of the industry continue to be attracted by the elusive prospect of uncovering a simple, viable means of direct reduction. Wild,3 one of the speakers at Evian, listed no less than 48 direct reduction processes (laboratory, pilot plant and commercial). Some of these were of historical interest only, but many others had resulted from developments within this decade. The previous big thrust into direct reduction occurred under the artificial impetus of a wartime economy (World War 11) and was largely an effort to provide more melting stock without coke ovens and blast furnaces. The present-day inquiry is proceeding at a more leisurely pace and the emphasis is different. For one thing, there is much less anxiety to circumvent the blast furnace. On the contrary, a whole new research endeavor has grown from the discovery that metallized burdens are exceptionally productive.4 Although the search for a melting stock

Jan 1, 1970

By F. H. Buttner, E. R. Funk, H. Udin

Gold wires, 5 mil in diam, are found to creep viscously up to approximately 5.5x106 dynes per sq cm around 1300°K. Beyond this point, an additional slip mechanism appears. The average coefficient in the viscous range at these temperatures is 18.9 ± 7x10 12 poises. This observation and other visual observations made during the experiments agree with Herring&apos;s predictions. EARLY creep studies by Chalmers on single crystals of tin produced some of the first experimental evidence to suggest that metals deform viscously under very light stresses. That is to say, over a small initial stress range up to 150 g per sq mm, the single crystals of tin elongated at a rate proportional to the stress. The proportionality constant between strain rate and stress is by definition the coefficient of viscosity. Chalmers named this range of proportionality the microcreep range. One of the first theoretical attempts to explain the microcreep phenomenon was given by Kauzman,&apos; who applied Eyring&apos;sQ eneral statistical mechanical theory of shear rates to creep data then available. From the rate theory, he deduced the general hyperbolic sine law for shear rate on the assumption that the distortion of the reaction path due to stress is negligible and that the system is an infinite continuum. In order to fit the available data to the equation, it was necessary to assume that creep occurs by shear of rather large blocks of material, rather than by an atomistic shear process as in diffusion. The size of the shear units was shown to increase with increasing temperatures and lower stress, or lower strain rates. In applying the hyperbolic sine law equation to the microcreep data of tin, it was shown by Kauzman that the unit shear blocks became quite small, which suggested to him that microcreep might be a self-diffusion process. Making this an assumption, Kauz- man reworked the rate theory and arrived at an equation where the shear rate is proportional to the stress. In the form of viscosity coefficient, the equation is: o- _ \LkT V = 2qAlA where u is the stress; S, the shear rate; X, the distance in shear direction moved by flow units relative to one another in the unit process; L, the distance between layers of units of flow; T, the absolute temperature; k, Boltzmann&apos;s constant; qAL, a constant proportional to the size of flow units; and kT A, the diffusion coefficient = ------kTe-Q/RT = K X2 h Kauzman applied the expression to molten lead with a fair degree of success, the calculated viscosity being low by a factor of four. For solid lead the result is 5000 times too high. Taking q = 1, and X = dA = L = 21 = nearest neighbor distance, Udin, Shaler and Wulff8 found the equation low by a factor of lo7 for solid copper. On the basis of the discrepancy in lead, Kauzman indicated that microcreep is probably not a simple diffusion process of molecular shear units, but one involving preferential diffusion paths, or even that diffusion in solids does not involve shear at all. Cottrell and Jaswon4 treat the microcreep phenomenon on the basis of slow moving dislocations and apply it to Chalmers&apos; data on tin with fair success. Nabarro Suggested a microcreep model in which mass movement in the direction of pull is effected by the diffusion of holes. The tension on the crystal effectively creates a greater hole concentration at regions near the crystal surfaces perpendicular to

Jan 1, 1953

By Amitava Gangulee, Michael B. Bever

The order-disorder transition in Ag-Mg alloys in the range 17 to 26 at. pct Mg was investigated and some thermodynamic, electrical and mechanical properties of ordered Ag-Mg alloys were measured. A modification of the phase diagram is proposed on the basis of measured transition temperatures. The stability of the ordered structure is analyzed in terms of the quasichemical theory. Kinetic aspects of the order-disorder transition were also investigated. The energies of ordering at 273°K of Ag-Mg alloys were measured by liquid metal solution calorimetry. The electrical resistivities and the tensile Properties of the ordered alloys were measured. The exothermic energy of ordering increased with magnesium concentration up to the composition Ag3Mg; it is discussed in terms of the quasichemical theory. Pronounced order hardening was observed and can be explained by several strengthening mechanisms, which are particularly effective because of a change in crystal structure associated with the ordering transition. IN silver-rich solid solutions containing approximately 17 to 26 at. pct Mg, long- range ordering may occur during appropriate therma1 treatments. Clare-brough and Nicholas1 first detected such long-range order in the solid solution of composition Ag3Mg and suggested that the unit cell of the superlattice contained 256 atoms. x-ray2 and electron diffraction3 investigations confirmed the occurrence of long-range order, but indicated a shifted Ll2-type structure. On the basis of recent X-ray measurements the crystal structure of ordered Ag3Mg has been confirmed as type D023.4 The present paper is concerned with the order-disorder transition in silver-rich Ag-Mg solid solutions and some thermodynamic, electrical, and mechanical properties of the ordered alloys. The effects of short-range order on the properties of silver-rich solid solutions containing up to 26 at. pct Mg are discussed in a concurrent paper.5 1) EXPERIMENTAL PROCEDURES 1.1) Preparation of Specimens. Specimens of Ag-Mg alloys containing from 18 to 26 at. pct Mg were prepared in the form of 1.0-mm-diam wires as described in Section 1.1 of Ref. 5. Disordered specimens were prepared by annealing at 773°K for 1 hr and quenching into iced brine. Ordered specimens were prepared by annealing at 773°K for 1 hr and slowly cooling to room temperature over a period of 15 days. The specimens were stored at 78°K. 1.2) Resistivity Measurements. Electrical resistivi- ties were measured by a potentiometric method.&apos; Equilibrium values were obtained at several temperatures. The kinetics of ordering were investigated by following the time-dependent changes of the resistivity of initially disordered specimens during annealing. The specimens were enclosed in copper capsules and immersed in salt pots; the heating up was accelerated by injecting preheated helium into the capsules. 1.3) Calorimetry. The energies of ordering of the alloys were measured in a tin solution calorimeter as the difference between the heat effects of additions of completely ordered and disordered specimens of the same composition. The procedure and the method of calculation have been described.6 Magnesium was used for thermal compensation in most calorimetric runs in order to improve the accuracy.677 1.4) Mechanical Tests. Tensile tests were carried out with wire specimens at room temperature as described in Section 1.5 of Ref. 5. Microhardness measurements were also made.? 2) RESULTS AND DISCUSSION The characteristics of the order-disorder transition of silver-rich Ag-Mg solid solutions will be discussed first. Some thermodynamic, electrical, and mechanical properties of the ordered alloys will then be considered and compared with the corresponding properties of dis-disordered alloys. 2.1) The Order-Disorder Transition. 2.1.1) Thermodynamic and Structural Aspects. The transition temperatures Tt were determined from discontinuities in the slope of the equilibrium resistivity vs temperature curves. Normalized curves for three compositions are shown in Fig. 1. The transition temperature increases with the magnesium concentration and reaches a maximum at the stoichiometric composition Ag3Mg. The transition temperature of the alloy Ag3Mg was measured as 665° ± 2°K and compares with published values of 660°,1 663°,8 and 66°k.3 In the slopes of the resistivity vs temperature curves of alloys containing 22.2 and 22.5 at. pct Mg, discontinuities were observed at two temperatures. Such upper and lower discontinuities indicate a two-phase field. A modified form of the published phase diagram9 is shown in Fig. 2. A two-phase field was found only on the low-magnesium side of the composition Ag3Mg. On the high-magnesium side, the existence of a two-phase field could not be established because of insufficient resolution, but such a field must be present. This part of the phase diagram can be made complete by a eutec-toid-type reaction a = (a&apos; + ß). The existence of a boundary between the two-phase fields (a + ß) and (a&apos; + ß) is also in accord with published lattice parameters.3 The crystal structure of ordered Ag3Mg (type Do23)

Jan 1, 1969