Search Documents

By T. L. Joseph

Sulfur balances calculated from operating data covering thirty-five blast furnaces indicate that approximately 92 per cent. of the total sulfur charged enters with the coke, 7 per cent. with the ore, and 1 per cent. with the stone.. Most of the sulfur is carried from the furnace by means of the slag, the total amount eliminated being the product of the slag volume and the percentage of sulfur it contains. Additional sulfur in the charge must be eliminated either by increasing the percentage of sulfur in the slag or the quantity of slag. From relations found between slag volume and coke consumption and sulfur in the coke and slag volume, curves have been prepared showing the relative value of blast-furnace coke as its sulfur varies from 1 per cent. CHARCOAL was the predominant blast-furnace fuel until 1838, when it was found, by the operation of a 2-ton experimental furnace, that anthracite could also be used. This information was a stimulus to the iron industry, particularly in eastern Pennsylvania where anthracite was available at low cost. The production of anthracite pig iron increased steadily and, in 1855, its tonnage exceeded that of charcoal iron. Of the 680 furnaces in operation in 1874, the 226 using anthracite produced nearly one-half the total tonnage. In 1869, the production of coke furnaces exceeded that of charcoal furnaces and, in 1875, coke surpassed anthracite as a metallurgical fuel. In 1907, the output of anthracite pig dropped well below a million tons and its present significance is largely historical. In recent years, the production of coke has gone hand in hand with the production of pig iron and it has gradually attained the position it now occupies as a universal blast-furnace fuel. Charcoal, however, has great merit as a blast-furnace fuel chiefly because of its freedom from ash and sulfur. The harmful effect of the latter and the necessity of keeping the percentage of this element in pig iron at a minimum are well recognized. Other contaminating elements can be reduced to specified limits in the steelmaking process, but the control of sulfur belongs essentially to the blast furnace. The purpose of this paper is to point out the distribution of this impurity in blast-furnace

Jan 9, 1924

By W. H. Emmons

MOST mineral deposits change as they are followed downward on their dips. Some of these changes are due to primary arrangement; different ores were precipitated at different depths when the deposits were formed. Other changes are due to weathering or secondary enrichment. The chief changes resulting from weathering, in the main, are understood and standard changes are recognized. The processes are relatively simple. They take place at ordinary temperatures and pressures and can be duplicated in the laboratories. Moreover, there are thousands of deposits available for study, because the processes take place near the surface where the development of mines is begun. The changes due to primary arrangement of the deposits of the metals are not so well understood. Deposition has taken place at higher temperatures and our knowledge of the chemistry of the processes leaves much to be desired. Very few experimental data are available. The deposits, moreover, offer fewer examples because many mines are not, developed to depths where the changes can be studied and a change to unprofitable material usually results in stopping work. Most, students of ore deposits now accept, as confirmed, the hypothesis that nearly all lodes and related deposits were formed by solutions originating in intrusive igneous masses. Outward from these masses, the deposits at many places are grouped in zones and the arrangement noted from the intrusions outward are commonly the reverse of the changes noted from the surface downward in a single lode. A study of the changes in groups of deposits, from the parent intrusion outward, will throw light on the changes to be expected in a single lode downward. Because the changes in series of deposits from the intrusive outward may all be observed near the surface, where more data are available, it is possible to increase the number of examples many fold and to apply the statistical method of study with greater confidence of avoiding error.

Jan 3, 1924

By Robert R. Walden, LaMont West

KENTUCKY'S first acid-grade fluorspar flotation mill, shown in Fig. 1, was placed in operation Aug. 1, 1952, by the Pennsylvania Salt Manufacturing Co. at Mexico, Ky. During 1951 a critical shortage of acid-grade fluorspar developed and it became necessary for the company to produce part of its fluorspar requirements. In 1951 the company purchased the Crider and Lennen metallurgical fluorspar mill and an adjacent stockpile of tailing at Mexico, Ky. The tailing, assaying about 26 pct calcium fluoride, originated from log washer and jig mill concentrators in the area. As the mill did not have a fluorspar dryer or convenient rail facilities, the company leased the Burleson concentrator at Marion, Ky., where these facilities were available. At Marion, Ky., on the Illinois Central Railroad, dry acid-grade fluorspar is transported direct to the company's Calvert City, Ky., hydrofluoric acid plant.

Jan 5, 1954

By R. E. J. Putman

Introduction Self-tuning regulators are a class of controllers built around the concepts of sampled data theory, and are especially suitable for implementation in a digital microprocessor or minicomputer control system. The algorithms used are distinctly different from those based upon analog control techniques and include automatic adjustment features which permit them to adapt to unmeasured changes (in, for example, ore grindability) or process nonlinearities (as exhibited by cyclone classifiers). They are also designed to handle transport lags in a simple manner, for example, anticipating the effects of a variable recycle rate on particle size distribution. The advent of distributed control systems will encourage the exploration of these techniques in the minerals processing industries, and particularly for improving the control of comminution circuits, which are especially energy intensive. This paper outlines some current work in progress on this topic. Background Those engaged in the practice of process control have long had two philosophical problems for which solutions have been actively sought - what is optimal control and how can we attain it in some heuristic fashion automatically. The basic analog controller can be represented by the differential equation: [V = Ko + K1 f y • dt + K2 dt(1)] where: v and y are the instantaneous values of output and error respectively and K0, K1, and K2 are tuning constants. The empirical rules for establishing the values of K0, K1, and K2, which provide stability, have evolved from the initial suggestions of Ziegler and Nichols(9) in 1942 and have served their purpose well. However, later analyses demonstrated that there are in fact many combinations of the values of K0, K1, and K2 which, besides being stable, behave better or worse in relation to other process control criteria; some examples are duration of error, amplitude of a damped response, magnitude or rate of movement of control valve or adjustment of speed regulator, etc. The definition of optimality had broadened. In 1964, Kalman(4) published his classic paper which tried to resolve these problems. He defined a

Jan 1, 1982

By L. Himmel, R. F. Mehl, C. E. Birchenall

The rates of self-diffusion of iron in artifically prepared wustites of various compositions have been determined using the decrease in surface activity technique. Similar measurements are reported for artificial magnetites of nearly stoichiometric composition and for natural hematite single crystals. These data, together with appropriate thermodynamic data derived from the present study or from the literature, are used to calculate the rates of oxidation of iron and its oxides, taking as a basis the theoretical rate equations developed by Wagner. The calculations are compared with experimental rate constant data for these same reactions and are shown to provide essential confirmation for the Wagner theory. For the most part, the results are also consistent with the previously proposed transport mechanisms in the oxides of iron. WHEN a metal is exposed to an oxidizing atmosphere at elevated temperatures, a superficial oxide layer is formed which then thickens according to some characteristic rate law. Provided that the oxide layer is dense and continuous and does not present any paths for gaseous diffusion, continued growth must inevitably involve the migration of the reactants—either the metal or oxygen or both—through the lattice of the solid oxide. This is true whether the reaction rate is controlled by the diffusion process itself or by a slow step in a reaction at one of the interfaces. If the overall rate is limited by diffusion, and if the concentrations or thermodynamic activities of the reactants at the boundaries of the oxide layer are independent of time, the familiar parabolic rate law is observed. Under these conditions, Wagner1 has shown that the rate constant may be expressed in terms of the mobilities of the reacting components and the appropriate concentration or activity gradients which are established across the growing oxide layer. In presenting the phenomenological basis for the theory, Wagner has emphasized the role played by lattice defects in diffusion processes in oxides. The essential validity of this theory has been confirmed by experiment for a number of simple systems including the growth of Cu2O on copper.'-' One of the objectives of the present study has been to extend the Wagner approach to the more complex process of the oxidation of iron and its oxides, and particularly to wustite, which is normally the major constituent of the oxide scales formed on iron at temperatures above approximately 570°C. For this purpose the rates of self-diffusion of iron in w?stite, magnetite, and hematite have been measured by tracer techniques and the necessary thermodynamic data have been obtained from equilibrium studies involving the oxides and their atmospheres. These data have subsequently been used to test the underlying assumptions of the Wagner theory as well as the detailed mechanism of the scaling of iron previously proposed by Davies, Simnad, and Birchenall.5 Lengthy treatments of diffusion and conduction phenomena in ionic crystals have been published." * The latest, by Jost,8 also summarizes much of the existing experimental data. In general, however, the oxides of iron have not been considered specifically and hence a brief review of the available

Jan 1, 1954

By C. D. Stahl, S. M. Farouq Ali

This investigation attempts to describe and simulate the alcohol displacement process by means of a cell model, as employed in chemical engineering practice. The proposed model is more simple than previously proposed models. and utilizes parameters chosen on a theoretical basis. The model successfully reproduced the formation of the stabilized bank and the breakthrough of alcohol, the latter depending on one of the model parameters, which may be correlated with the length of the porous medium. Moreover, the effects of the phase behavior of the liquid system involved, as observed in experimental studies, were reproduced. Several variations of the basic model were devised and tested on a digital computer. These included the cases in which: (1) the actual value of fractional flow was used in cell-to-cell computations; (2) the number of cells was varied within the same run; and (3) incomplete rather than complete phase equilibrium was assumed within each cell. The proposed cell model clarifies the basic mechanism of the process. Detailed concentration profiles obtained for each cell, for instance, showed the mechanism of bank formation in relation to the phase behavior characteristics. The results obtained indicated a varying degree of phase equilibrium concommitant with changes in the velocities of the phases in an actual alcohol displacement. This condition was approximated by changing the number of cells during the simulation. Interesting information was obtained on the influence of path length on the efficiency of alcohol displacement, which has been the subject of some controversy. Certain limitations preclude the use of the proposed model as a substitute for experimental studies. The results obtained were, nevertheless, of value in interpreting the experimental results. INTRODUCTION During recent years considerable effort has been directed toward an understanding of alcohol displacement, the process whereby oil and water are recovered from a porous medium by the continuous injection of a solvent. The complex nature of the physical process involved has so far defied a complete mathematical treatment. Other methods of approach, amounting to an overall material balance, have been proposed, yielding useful information on certain aspects of the process.1-3 Taber et al, in particular, defined the displacement mechanism in terms of the phase behavior of the alcohol-oil-brine system invoIved.2 Wachmann reported a mathematical treatment of alcohol displacement subject to certain simplifying assumptions? Donohue proposed the use of a "cell model" for simulating alcohol disPlacement.5 The nature of the assumptions involved limited the utility of the model. The present work attempts to examine the variables involved in the simulation of alcohol displacement and discusses several possible versions of the basic cell model. Under certain conditions the model results are similar to the experimental results. In particular, the spontaneous formation of of the stabilized bank and the effects of the system phase behavior were successfully reproduced. PREVIOUS WORK ON CELL MODELS Cell models and the theoretical plate concept are often used in solving chemical engineering problems in which an explicit mathematical solution may be difficult or impossible to obtain. Examples of such applications occur in distillation, gas-liquid chroma tography,6 reactor technology, absorption, etc. In petroleum engineering, such a model was used by Attra7 to describe non-equilibrium gas drive, and by Higgins and Leigh ton8 to calculate sweep efficiency in water flooding. Aris and Amundsen pointed out the equivalence between the diffusion model and perfectly mixed cells connected in series.9 Deans proposed a three-parameter cell model to simulate two-component

Jan 1, 1966

A New Process Builds An Industry

Jan 7, 1951

By Anthony Anable

THE definite trend to stricter specifications with respect to hydraulic concrete has become increasingly manifest in the last six years or so; but it remained for the vast reclamation projects of the Bureau of Recla-mation of the Department of the Interior of the last few years to focus attention on this trend, and to demonstrate how thousands of tons of concrete-making aggregates can be produced continuously and auto-matically with a control of fineness comparable with that obtained with small samples in well equipped private and governmental laboratories. Pioneer work in this direction was done, to be sure, by private com-panies, notably the Kaiser Paving Co. of San Francisco, prior to the present vast public works program. Then in 1931 came the first great, aggregates-preparation plant of the Six Companies, Inc. to supply construction materials for Boulder Dam' in Nevada, and now, in 1936, the aggregates plant of the Mason-Walsh-Atkinson-Kier Co., general con-tractors on the Grand Coulee dam in Washington. At Boulder dam and to an even greater degree at Grand Coulee dam, sand production is recognized as probably the most important single element affecting the physical characteristics of the concrete. For in the construction of dams accurate grading of the fine aggregate has consider-able bearing on the attainment of a uniform and homogeneous concrete of a high degree of workability and placeability and, at the same time, combining high density and low cement content. Low cement content is of value not only from the standpoint of economy but also because the use of an unnecessarily rich concrete causes certain undesirable characteristics to develop. This paper will relate how at Grand Coulee dam methods that are more advanced than ever before are producing four sizes of gravel and a sand having a fineness modulus of 2.5-3.0. The design capacity is 1000 tons an hour. Significantly, the methods and equipment employed are broadly those that have been used for a generation in metallurgical mills for accurately sizing and grading both precious

Jan 1, 1936

By L. K. Jetter, C. J. McHargue

The use of axis charts for representing the texture of cold-rolled thorium sheet was compared with conventional pole figures. Four texture components were deduced from the axis charts and shown to be consistent with the pole figures. It was shown that consideration of the pole figures alone could lead to an apparent component which is the average of two actually present. It was also shown that the spread about the "ideal" textures and the amount of material associated with each could be readily obtained Fom the axis chart method. BECAUSE of the crystallographic nature of the deformation mechanisms in metals, plastic flow results in the alignment of certain crystallographic directions with the primary flow directions. In the study of the "preferred orientation" thus developed, one wishes to discern the distribution of the crystallographic directions with respect to some reference direction, usually a direction related to the fabrication procedure, such as the rolling direction. The pole-figure method, introduced by ever,' involves the plotting of the distribution of the poles of some family of planes on a stereographic projection which places the reference direction(s) at the north pole and/or in the center. By noting the angles between the reference directions and concentrations of poles on several such pole figures, one can deduce the crystallographic directions which are aligned with the reference directions. If the preferred orientation is relatively simple and well-developed, one to three pole figures may be sufficient for obtaining the desired information; if there are several texture components, more pole figures may be needed. A significant improvement in the method of representing the textures in wires and rods resulted from the introduction of the "inverse pole figure" or axis-distribution chart by Harris.2 Such a chart gives directly the distribution of the reference axis relative to the standard stereographic projection. There has been widespread acceptance of this method for the representation of fiber textures, and methods have been proposed for converting observed diffraction intensities into axis densities.2-6 The suggestion by Mitchell and Rowland3 and Jetter, McHargue, and williams5 that sheet textures could be represented as distributions of rolling, normal, and transverse directions have been criticized on the basis that they offer no significant advantage over a combination of two ordinary pole figures and that it has not been proved that sheet textures can be treated as quasi fiber textures.6 If the purpose of a texture determination is to study some property which is related to the orientation of a particular crystallographic plane or direction, then conventional pole figures certainly are sufficient. For example, the distribution of the slip planes in face-centered cubic metals (the (111) pole figure) serves to indicate the variation in mechanical properties of sheet. On the other hand if the study is directed at an understanding of the factors influencing texture formation, it is desirable to know not only the preferred orientation but the kind and degree of spread from it and the relative amounts of material in each component, if there are more than one. Axis charts give this information as well as the orientation distributions. Consider the procedure for deducing a texture component from a pole figure for the (111) planes

Jan 1, 1961

By Peter G. Groer

Several methods1-3 are being used to determine the WL and individual Rn-daughter concentrations in uranium mine atmospheres. The best of these methods is the one given in Ref. 3. According to this method, the WL and the Rn-daughter concentrations are determined from the total a-counts observed during three consecutive time intervals. Its only disadvantage lies in the fact that rather involved calculations are necessary to convert the observed counts into WL or pCi/l (picocuries per liter). There are, however, counting intervals that give simple weighting coefficients for the observed counts. This fact makes it possible to convert from a-counts to WL or pCi/l with the aid of a graph. After some trial runs on a computer the following equations emerged as the basis for the most practical procedure: [ ] NA, N.., and & stand for the number of RaA, RaB, and RaC atoms per liter of air. C(t1,t2) denotes the counts observed from time t. to time t2 (in minutes) after the end of the 5-min sampling period. E is the detector efficiency and V is the flow rate in liters per minute. With an accuracy loss of less than -5% one finds from [Eq. 1] by adding the corresponding terms: If the WL would have been calculated according to [Eq. 2] instead of using the graph, the result would have been 0.31. Since the values used for C's under [Eq. 3] represent the exact number of counts from a Rn-daughter mixture in equilibrium with 100/3 pCi of Rn the exact WL of this mixture can be calculated easily. The exact value is: [ ] This shows that the method is quite accurate for the 0.3 WL domain. The precision of the method excluding errors made in reading the graph can be estimated with the help of the following formula: [ ]

Jan 1, 1974

By H. S. Price, J. C. Cavendish, R. S. Varga

This paper presents a new technique for solving some of the partial differential equations that are commonly used in simulating reservoir performance. The results of applying this technique to a simple problem show that one obtains accurate pressure values near wells, as well as accurate pressure pdients, which can be explicitly calculated. The method is completely rigorous in that convergence of the discrete numerical solution to the continuous solution for both pressure and pressure gradient is established. High-order, piecewise-polynomial approximations are used near the wells where pressure gradients are steep, while low-order, piecewise-polynomial approximations are used elsewhere to reduce greatly the calculation time. This combination is shown to give a uniformly good approximation to the solution. These approximations, obtained by using a Galerkin process with suitable Hermite subspaces, are shown to be theoretically and numerically superior to the usual approximations obtained from standard finite-difference techniques. Not only are much greater accuracies obtained, but computer times are also greatly reduced. The application of this technique to multiphase flow problems (e.g., single well coning problems) would have considerable practical interest, but such extensions of this technique with full mathematical rigor have not been made as yet. However, the numerical methods presented here are general, and in principle extend to multidimensional, multiphase flow. Moreover, the preliminary results given in this paper are sufficiently encouraging that we feel the effort in attempting these extensions is justified. INTRODUCTION The problem of obtaining accurate pressure distributions and pressure gradients around wells is of considerable importance in the numerical simulation of reservoir performance. The most common approach to solving this problem is to use finite difference techniques (see McCarty and Barfield9 or Peaceman and Rachfordl0). This approach, however, has many disadvantages, the major one being that many grid points are generally necessary for accurately describing the pressure distribution and the pressure gradient around wells. This need for a fine grid results in large computer times and often in prohibitively high costs. Besides investigating the method of finite differences, some authors, such as Welge and weber17 and Roper, Merchant and Duvall,13 have considered a combination of analytical and numerical techniques with some success. These approaches, however, are all nonrigorous and quite often cannot even be applied. In this paper, we present a numerical formulation of high-order accuracy, based on the Galerkin method, for solving this problem. We treat here only the partial differential equation that describes steady-state, single-phase flow. However, the methods presented are general and in principle extend to multidimensional, multiphase flow. Specifically we treat special cases of the problem in two dimensions described by: where G is a rectangle (with sides parallel to the coordinate axis) with boundary ?G, ?/?n denotes the outward normal, and y and B are non-negative constants such that y + B > 0.

Jan 1, 1970

By A. C. Stevenson

IN OUTLINING the various steps taken and the exigences met during the time of unwatering and rebuilding the burnt top equipment at the Hecla mine, the major portion of the detail is omitted and a general description of the experience only is given. All the electrical power lines were out of commission, as were the mine feeder cables. The first effort, there- fore, was to restore electrical connections. The Washington Water Power Co. immediately put a crew to work restoring the power line, it being necessary to rebuild about 4000 ft. of 66,000 volt transmission and about 2000 ft. of 2200 volt feeder. This work was rushed and power was again available at the mine sub- station about 26 hours after the fire. During the same time temporary lighting lines were strung and transformer equipment obtained, so that when electrical connection was resumed the lights were turned on and the dump well lighted that night.

Jan 1, 1924

By K. E. Manchester, A. H. Clark

Hall measurements have been made on three groups of silicon samples, which were implanted with boron, aluininunz, and phosphorus ions. Boron and phosphorus implants show essentially bulk properties when annealed under previously determined conditions, i.e., 15 min at 80O°C for boron and 10 mirz at 600°C for phosphorus. Bulk properties were also observed in alu?rrilzum-implanted samples when ion concentrations were below 1015 cm-'; however, strange low- terrzperalure behavior and a falloff in cavrier concenlralion was observed for sarnples with ion concenlration abozle loL5 ern-'. This can be attributed to solid-solubility effects since the average bulk concentration f0.r the sample exhibiting bulk properties was below the reported solubility limit for aluminum, while the other samples were above the limit. A detailed study of the annealirzg process indicates that mobilities reach bulk c~alues in phosphorus implants at 250DC, in alutninurn ivnplanls a1 500°C, and in boron implants at 700°C. A simple rnodel has been proposed to fit the annealing data. THE technique of semiconductor doping by direct injection of energetic ions is being actively investigated at this Center. Previously published results from this laboratory have been concerned with the investigation of implanted profiles in silicon and the electrical properties of the resultant p-n structures.1'2 Diode properties have been reported for junctions produced by implantation of boron ions and aluminum ions in n-type silicon and phosphorus ions in p-type silicon. Reverse current characteristics, as well as electron diffraction data, have indicated that the damage to the structure produced by the energetic ions during the stopping process can be minimized by a gentle anneal. The time-temperature conditions for this process have been determined by sheet resistivity studies.3 Electrical profiles of implanted phosphorus ions which have been determined by a differential sheet conductivity technique are based on the assumption that the carrier mobilities and activation energies for ionization are the same as in bulk silicon. These assumptions have been substantiated experimentally by measurement of Hall constants and resistivities of these implanted structures and the results are presented herein. After establishing the bulk property equivalence of the annealed layers, a more detailed examination of the annealing process was undertaken. The sheet resistivity technique initially used to determine anneal conditions has been broadened to include Hall constants and mobility behavior with anneal conditions. PROCEDURE The three groups of samples prepared for Hall measurements were implanted with mass-separated beams of boron, aluminum, and phosphorus ions. Ion concentrations are equivalent surface concentration and they have been determined from beam current measurements during implantation. Implant conditions for the samples are shown in Table I. In all cases, the samples had previously been angle-lapped on one edge and the junction delineated with an HF-copper sulfate solution. The surfaces of the implanted regions of the samples were exposed to the delineating solution and in the case of the "n"-type phosphorus-implanted areas it was later discovered that a finite amount of surface could be etched by this solution. This is discussed in the section on results. The implanted samples were ultrasonically cut into the conventional six-probe configuration shown in Fig. l.* In the annealing studies, for which the meas- urements were taken at room temperature, the sample holder was a Bakelite jig incorporating tungsten mechanical probes. The other measurements were taken using a conventional liquid-nitrogen cryostat, in which the temperature could be varied from 77" to about 400°K. For these measurements, 10-mil aluminum dots were evaporated onto the samples and alloyed with the silicon at 530°C for 15 min. The samples were then mounted in flat-packs, and gold wires were bonded to the aluminum dots. The electrical measurements were made with either a Leeds & Northrup K-5 Potentiometer, a Keithley 147 Nanovolt Null Detector, or a Keithley 601 Electrometer. No external bias was applied to the substrate. There is an inherent self-biasing arrangement at one or the other of the current contacts (depending upon the polarity), and this suffices to limit the current flow to the implanted layer. The magnetic field was generated by an A. D. Little electromagnet. Except for occasional checks of linearity of the Hall voltage with

Jan 1, 1969

By R. W. Newcomb

THE constancy of calibration, and to a great extent the life, of a thermoelement is dependent on the suitability of the primary protecting tube in which the wires are mounted, particularly when used at high temperatures. An ideal thermocouple protecting tube would be com-posed of materials that would not contaminate the thermoelement wires contained in it-one that would remain absolutely gas-tight ,it all temperatures of usage, that will not be attacked by gases, or other surrounding agencies, that is not destroyed by heat, that withstands sudden and extreme temperature changes, that affords a high degree of mechanical protection and does not deform at high temperatures, that is a good heat conductor and obtainable in small diameters so as to keep down lag factors. It has not yet been possible to produce tubes of any known mate-rials that will meet all of these conditions. In selecting protecting tubes, therefore, one should be chosen the characteristics of which best fit it to the particular conditions of usage. Frequently conditions are such that two tubes have to be used, a primary gas-tight protecting tube inside of a secondary protecting tube, because certain agencies will attack the primary gas-tight tube unless it is guarded by the outside tube.

Jan 9, 1919

By N. N. Breyer, W. R. Warke, S. Dinda

A model for the low-temperature peak, LTP, in fcc metals is presented. In high stacking fault energy metals, e.g., aluminum and nickel, it is proposed that a reversible dislocation glide and climb process might give rise to the observed high relaxation strengths and activation energies equivalent to volume self-diffusion values. In low stacking fault energy metals such as copper, gold, and silver, dislocation climb is energetically unfavorable at T < 0.5 Tm and the relaxation process is therefore mainly one of reversible glide. This model is used to explain the effect of a change in grain size and impurities on the LTP. THE low-temperature grain boundary damping peak, LTP, in spectroscopically pure aluminum,&apos; copper,17&apos; gold,2 nickel,3 and silver4 has recently been the subject of a detailed investigation by our laboratory. The main results are summarized in Table I. An empirical relationship was found between the peak relaxation strength, AE, and the width of the dissociated dislocation, do,* given by: do = µa2/24p? (Ref. 5) [I] where p is the shear modulus, y is the stacking fault energy,6-8 and a is the lattice parameter, Table 11. 4E is plotted against do in Fig. 1. Two regions are apparent: region (a)! which contains all but one of the metals, where AE decreases linearly with increasing do, i.e,, AE 1/do; and region (b), where ?E is approximately independent of do. A similar trend is observed when the ratio Qp/QL is plotted as a function of do, Fig. 2. (Qp and Ql are the activation energies for the peak and for lattice diffusion, respectively). In the past, when Qp and QL were found to be comparable, the relaxation peak was explained in terms of grain boundary sliding.10 The equivalence of Q, and Qb. the activation energy for grain boundary diffusion, prompted the suggestion that it was a consequence of reversible grain boundary migration on an atomic scale." A new model for the LTP, which is based on the experimental relationships in Figs. 1 and 2, is presented. In region (a) it is suggested that stress relaxation occurs through the reversible glide and climb of grain boundary dislocations; in region (b) only reversible glide can take place. The resultant effect on the grain boundary might be sliding or "a bowing out", but, since the total distance moved will be 50A, the atomic movements are considered of primary im- portance. It must be emphasized that this is only a qualitative model, but at the moment it appears the most likely way to explain the widely varying, but re-

Jan 1, 1969

By Frederick Laist

I AM APPRECIATIVE of the honor you have done me in electing me to membership in your Society. I value the contacts with men of imagination and ideals which this implies. I am grateful for the recognition of such small contributions as I may have made, or helped to make, to the vast fund of scientific and engineering knowledge. We like to think, as we grow older, that our lives have not been purely parasitical, and that through our efforts some forward step, however small, has been taken toward improving conditions under which we live and do our work. In these days of industrial depression, we hear much criticism of our "machine age." Modern engineering, mass production, the complexity of our lives, all come in for some share of blame. The farmer is said to have been spoiled by the tractor and the gang plow, the factory worker has become a slave of the assembly conveyor, the scientific worker is no longer free but has sacrificed much of his individuality to the research organization of which he is a part. We wonder whether our work as engineers has been worth while and whether our striving after more efficient ways of doing things has been a curse to mankind rather than the boon we thought we were conferring.

Jan 1, 1932

APPROXIMATELY 3500 people thronged the Hotel Statler from February 18 to 24 for the 173rd general meeting of AIME. It was a technical extravaganza in that 82 technical sessions were held, at which 500 authors presented some 350 papers. Fortunately, Jerry Peirce, outgoing President, didn&apos;t have, to preside at all the events although after his year&apos;s stint as President, he has more than a nodding acquaintance with some of the latest problems in the mining, metals, and petroleum industries. Although the Welcoming Luncheon on Monday noon was the official opening of the meeting, Local Section Delegates and the Board of Directors convened on Saturday and Sunday, respectively. The large attendance and business like demeanor of these two groups was in accord with the energetic and competent service they have rendered the Institute through the year. To the applause of engineers and their wives who thronged the grand ballroom of the Statler for the Welcoming Luncheon, President Peirce introduced Oliver B. Hopkins, president of the Canadian Institute of Mining and Metallurgy and C. Gerow, secretary of CIM. Dr. Hopkins brought greetings from the CIM and expressed his satisfaction in the splendid spirit of cooperation that exists between the two Institutes. Dr. Hopkins is president, Interprovincial Pipe Line Co., Toronto, and counts as a close personal friend M. L. Haider, who is the 1952 President of AIME and lately of Toronto where he was a director and general manager of Imperial Oil Ltd. Mr. Haider will be known shortly as Mike to thousands of AIME members as he makes his Local Sections presidential tour. There was a pause in luncheon proceedings when Judge Harold R. Medina arrived amid the applause of the audience and somewhat breathless from his trip via motorcade from an antitrust trial against investment bankers at the courthouse downtown. With the Judge at his elbow, President Peirce took the opportunity in his introduction to good humoredly chide the Judge for the vixenish habits of public servants in their treatment of astute businessmen. The successful inventor who patents his inventions is a monopoly; the copper manufacturer who buys his competitors a drink is in collusion; but the business failure need only look to the government for a subsidy, Mr. Peirce pointed out. Judge Medina, quickly captured the admiration of his listeners. He spoke about justice, deploring partisan deals on nominations for judge-

Jan 1, 1952

Organization Place Date 1917 Electric Power Club Hot Springs, Va. June 11-14 Society for the Promotion of Engineering Edu¬ cation Evansville,Ind. June 19-22 American Institute of Chemical Engineers Buffalo, N. Y, June 20-22 American Institute of Electrical Engineers Hot Springs, Va. June 25 American Society for Testing Materials Atlantic City, N. J. June 26-30 Mine Inspectors Institute of U. S. A. Indianapolis Ind. July 9-11 National Association of Stationary Engineers... Evansville, Ind. Sept. 10-15 National Exposition of Safety and, Sanitation .. New York City Sept. 10-15 American Iron, Steel & Electrical Engineers.... Philadelphia, Pa. Sept. 10-14

Jan 6, 1917

By C. C. Nitchie, G. S. Brooks

With the gradual depletion of the natural-gas pools of the Kansas district, together with the uncertainty of further cheap fuel developments, some of the western zinc companies turned to the coal fields, attracted by their permanency and the success of the Matthiessen & Hegeler Co. and the lllinois Zinc Co. Being then confronted with the problem of using a relatively high-priced fuel, although the ultimate supply was very great, the fuel economies of the kilns and furnaces became of far more importance, and the more modern equipments, as a result, embodied distinct gaias in this phase of the business. In addition, there have been some pronounced advances in the actual making of gas from these coals. Increased efficiency in gas making has contributed its hare to lowering costs and those plants located in the higher priced fuel districts have probably been obliged to study these economies somewhat more closely. Naturally, many beneficial changes have resulted in both practice and apparatus in these sections. On certain western coals, for instance, the actual saving in fuel consumption has been 50 per cent. By this is meant that, where about 1.75 tons were burned to smelt 1 ton of oxidized ore, 0.7 to 0.9 ton is now required. While comparisons by T. R. Ingalls1 of fuel economies in smelting in this country and Germany before the war may, in general, be correct, they do not appear to do justice to the more progressive American practice. It is doubtful whether German plants were substantially bettering these fuel ratios. Data furnished by Bender and Frams do not afford records averaging less than 0.9 ton coal per ton ore on materials from 40 per cent. to 50 per cent. zinc. Fuels As producer fuel, Illinois, Indiana, and Kansas coah offer a wide range of material, although varying much in their amenability to gasscation. The proper fuel for each plant can only be determined after com-

Jan 1, 1920

By M. G. Corson

THE theory of hardening by interference with slip which has been so clearly developed by Jeffries and his co-workers requires that an alloy to be amenable to age or heat hardening should contain among its components some that will stay in solid solution at high temperatures and precipitate as a secondary phase on cooling. This secondary phase may be either a more or less pure individual element (chromium in the case of copper, anti-mony in the case of lead), or some intermetallic com-pound. Those cases of hardening which depend on the precipitation of a compound are not only the most frequent, but are also far superior in the efficiency of hardening obtained. However, the slip interference theory as stated in its most general form is not sufficient to foretell new cases of this type of hardening and also will not explain some phenomena of a more intricate nature. It is not sufficient that a secondary phase might be absorbed by the main one at high temperatures and precipitated at the lower ones. The kinetics of this precipitation and the accompanying. physical phenomena of dimensional changes play independent and highly important parts. These kinetics, while not yet sufficiently studied to he formulated in the shape of physicochemical equations, might find their expression-in a qualitative systema-tization of the phenomena of precipitation according to two different viewpoints. To begin with, we encounter the question as to the velocities of the precipitation and of the growth of the phase precipitated. To harden a metal in an efficient manner we must be able to control the precipitation on one hand and also to bring the total of the secondary phase to such a number and size of the particles pre-cipitated as, will produce a desirable hardening effect under commercially feasible conditions of. age or heat hardening. From this viewpoint six different cases may be dis-cerned.

Jan 7, 1928