Search Documents

By Gregory M. Dexter

Recent litigation in Pennsylvania between three coal-mining companies and a private water company resulted in the payment by the coal companies of the equivalent of about $500,000 to buy a new water supply to replace that which had been damaged by acid drainage from strip mining. An investigation of the relevant facts indicates that the water could have been treated by spending about $40,000 on equipment and $15,000 yearly for chemicals, labor, and power until the contarnination could be reduced about 80 pct. The water company's supply, furthermore, had deteriorated largely by reason of dry weather before stripping was begun by the coal companies. Payment to the water company should not have exceeded $300,000 and could have been as low as $100,000. Strip mining of coal is common in Pennsylvania. The most important objection to it in Pennsylvania is generally acid pollution of runoff water. An outline of the methods, therefore, that could be used to reduce such pollution, to compare acid-contaminated waters. and to treat such waters to make them satisfactory for public and industrial use is worth-while. The watershed of the West Penn Water Co. covers about 4.5 square miles, 20 miles west of Pittsburgh, and has two 90,000,000 gal reservoirs supplying about 1,300,000 gal daily for public and industrial use of which 450,000 gal daily are for two railroads. The pollution arises from weathered derivatives of typical'" Coal Measures"' rocks, the principal source being pyrite (and marcasite) in Pittsburgh and Rooster coals. Springs and seeps on hillsides issue from sandstone and limestone formations intersecting shale or clay land surfaces, or from perched water tables. The two reservoirs create an artificial permanent water table. Soap-hardness tests on three seepage samples taken in a dry summer ranged from 150 to 500 ppm. Water sampled came from aquifers above Pittsburgh and Rooster coals, obviating the possibility of contact with pyrite-containing coal. Since acid contamination of mine waters is the result of chemical reactions of oxygen and water with pyrite, it will be reduced by the exclusion of either air or water. The Sunnyhill Coal Co. has applied this principle in its "contouring" method of strip mining by burying contaminated coal-waste material under a compact, smoothed-up surface of top-soil, gravel, clay, and sand at a cost

Jan 1, 1950

By C. J. Osborn

In oral discussion at the Columbus midyear meeting, September 26, 1949, these pertinent questions were asked: Was a satisfactory separation of metal and matte obtained? The matte was quite fluid and in most cases the separation was satisfactory. Were the mattes chlorinated after aging? The mattes were stored in sealed glass mason jars, and chlorina-tion experiments made after standing for several weeks gave satisfactory results. Was ferric chloride volatilized? Most of the iron content of the matte was converted to ferric chloride. However, because of the low chlorination temperatures used (150" to 250°C) the major part of the ferric chloride remained with the residue. Undoubtedly, some ferrous chloride was also formed, because of the reducing conditions within the reaction vessel, but no effort was made to separate it from the ferric chloride. Could the reaction be stopped before making metallic iron? No attempt was ever made to stop the reaction before making metallic iron. Generally, 20 to 60 pct of the iron in the charge was obtained as metallic iron which could be readily separated from the matte. In certain cases, metallic iron was dispersed through the matte in the form of globules, which could be removed by magnetic separation. Could other sulphides, i.e., calcium sulphide or sodium sulphide be used in place of iron sulphide? No other sulphides were investigated. It was felt that titanates of calcium and sodium would be formed should these sulphides be used to replace the pyrite. What were the sulphur volatilization losses during matte smelting? In the course of this laboratory investigation, a rather wide variety of variables was introduced from highly oxidizing to reducing conditions and various ratios of pyrite, rutile, and coke. These and other factors all have a definite bearing on the sulphur losses. In general, the higher the sulphur in the charge the higher were the sulphur losses and the percentage of titanium in the matte decreased. With sulphur additions more nearly the theoretical amount, the sulphur losses averaged approximately 10 to 15 pct. With a higher percentage of sulphur on the charges, the losses were in the order of 15 to 30 pct.

Jan 1, 1951

By D. C. Seidel, E. F. Fitzhugh

Nickel sulfide ores lend themselves readily to concentration before smelting or pressure leaching, but neither of the major oxidized ore types-the iron-rich laterites and magnesium-rich, soft silicates-has been directly concentrated. Upgrading of crude ore in current practice is limited to cobbing lumps of the harder, lower grade rock (protore) from the softer, enriched silicate ore, because only a small percentage of the nickel in these ores occurs in discrete, contrasting mineral particles. There is no apparent mineralogical contrast in the superficial, iron-rich lateritic ores and, in fact, there is no firm assurance that the nickel atoms are within the lattices of the limonite minerals, or else irregularly adsorbed on the limonite. Within underlying, "rotten rock" silicates, occasional veinlets of garnierite and related nickeliferous silicates are found.1 The garnierite veinlets are only incidental, and the majority of the nickel atoms occur as erratic replacements of magnesium atoms in the micaceous chlorites of the ore mass.

Jan 4, 1968

By Norman Hedley, George Barsky, S. J. Sawinson

The cyanidation of precious-metal ores is a complex chemical process. Numerous reactions occur, some of which cause an undesired consumption of alkali and of cyanide. A knowledge of these reactions, their products, and the factors that influence the rates at which they proceed should be of value in working out the most economical conditions for cyanidation; but at present, much of this knowledge is lacking. This paper is confined to a study of some of the fundamentals of cyanidation. At the start of such an investigation it is necessary to simplify the problem under consideration by eliminating as many variables as possible. The results are then, of course, not immediately applicable to practice, but it is hoped in further work to round out the information and thereby make it of more practical value. For convenience in presentation, the paper has been divided into two parts, one devoted to a study of the reaction between cyanide and gold or silver, the other to a consideration of the factors that determine the rate of dissolution. I. REACTIONS INVOLVED IN DISSOLUTION OF GOLD AND SILVER IN DILUTE CYANIDE SOLUTIONS Ever since the cyanide process for gold and silver extraction was introduced there has been discussion of the equation representing the reactions involved. In undertaking a detailed study of these factors, it was felt that the most logical first step was to determine, if possible, what reactions could theoretically take place when gold and sill-er are dissolved by dilute cyanide solutions. It is possible to determine whether or not a given reaction will theoretically take place by calculating the free energy of the reaction. This free-energy value for any given reaction is the algebraic sum of the free energies of formation of each of the reactants and products, and, if these values are known, the calculation is simple. (A chemical change always involves an energy change and the amount of energy change involved is the factor determining whether a given reaction will take place or how far it will go. In chemistry we consider what is known as the "free energy"; that is, the maximum amount of energy that can be utilized as

Jan 1, 1935

By G. B. Walker

THE sink-float methods designated by heavy-media separation processes were pioneered by C. Erb Weunsch for the treatment of base metal ores as an improvement over jigs. The work of Weunsch was further developed by Victor Rakowsky and The American Zinc, Lead and Smelting Co. Early in the development of the processes, the inherent unsuitability of galena as the solid constituent of the medium was recognized and ferrous media amenable to magnetic recovery and control were developed. The high efficiency and low cost of magnetic recovery and cleaning of ferrous media regardless of particle size, slime contamination, or surfacial oxidation had led to the adoption of ferrous media by all of the sink-float plants operating under the heavy-media separation processes patents controlled by American Zinc, Lead and Smelting Co. Approximately 2,000,000 tons of base metal and nonmetallic minerals are treated each month by these methods.

Jan 1, 1949

By J. Brian Eby

As is generally understood, the word geophysics means literally ?the physics of the Earth? and the science of geophysics is therefore that which treats of the study and measurements of the various physical properties of the Earth. The broad and general study of the elastic, the gravimetric. or the magnetic properties of the Earth as a whole belongs to the general science of geophysics. The detailed application of this science to rocks of shallow depth and in small areas for the purposes of ascertaining data on their character and structural attitude gave rise to the present well-known science of ?applied geophysics.? Since the discovery of enormous new quantities of oil, gas, and sulphur has been by far and wide the principal benefaction of geo-physics in the United States, this paper will refer only to geophysical methods employed in the search for these particular minerals. The application of methods and appliances originally used for geophysical research to the solution of the practical problems of finding new oil-fields, plus the counterflow or new and highly refined techniques and Instruments from the company and consulting geophysical research laboratories and into non-economic geophysical research, has provided another case of that gen-eral cycle of events which is familiar to all scientists. That this closed-circuit flow or scientific current has been tremendously important to the whole science of geophysics is probably well known to all members of this audience, but the gen-eral status of the exploratory geophysical arts as now used In the search for new oil-fields, the scales on which different methods are being used, the magnitude of the costs involved, and the far greater magnitude of the practical results achieved may not necessarily have come so directly to your attention. It is, I understand, for this reason that this paper has been sug-gested, and I shall seek to provide the information requested by using as case-illustrations those changes in the oil-reserve picture for the United States as a whole, and for the Gulf Coast, California, and Illinois Basin regions in particular, which have occurred in the period of the past 17 years, during which time oil-field discoveries have proceeded at a rate which served to build up known and readily-available (or proven) oil supplies to a reasonable figure, and have dispelled the fears of a serious oil shortage during any period for which valid fore-casts can be made. Not that geophysical-prospecting methods have alone been responsible for this transformation, but they have an indispensable and leading part in the picture of exploration and production-to which geophysics, geology, engineering, and general technical progress have jointly made contribution. So far as the United States as a whole is concerned, its total proven, probable, and possible oil reserves (discoverable and recoverable by then-known methods) were estimated at about nine billion barrels in 1920, whereas proven reserves alone are now com-puted at about 16 billion. In 1920 the driller in ?wild-cat? territory was faced with the knowledge that for every new oil-field opened by a successful well, from 20 to 100 unsuccessful wells would have to be drilled and, in some territories, that the chances for a discovery were really less than one in 100 for new drilling, in contrast to which may be cited the record for the past year in parts of Louisiana where the 67 wells drilled opened 16 new oil-fields, that is to say, where the score of hits to misses was increased to approximately one out of four.

Jan 1, 1940

By J. S. Marsh

TUESDAY, Feb. 16, was no day for strolling along the cold sidewalks of New York, and a large number of metallurgists sat down with pleasure to the warming task of wiping a few soldered joints. Presented by a joint-wiper of the modern school, G. M. Bouton, of the well-known team of Schumacher, Bouton, and Phipps, the initial paper brought into focus the theme of conservation of strategic metals and described the technique of making the fillet-type joint now employed by the Bell System. Using an over-all average of only 40 per cent of the solder formerly used by the conventional method. this important development bids fair to stick when the war is over. D. L. Martin and E. R. Parker then described the embrittling effect of hydrogen on silver previously heated in oxygen and the less serious but troublesome result obtained under the converse conditions. An interesting example of grain growth restriction created additional material for the lively discussion that ensued among those who have encountered one or another of these phenomena in silver and copper.

Jan 1, 1943

By E. Posnjak

IT is rather the general belief that acidified, solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as. cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by passing air for 3 hr.. through solutions of Mohr's salt acidified with sulfuric acid." While this statement will bee proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2 His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 12, 1926

By T. I Harkins, J. Brian Eby

This paper outlines the geophysical investigation of the area covering the Darrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The Darrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook1 and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outline and comes to within about 4625 ft. of the surface. At this depth the diameter of the salt plug is approximately 4800 ft. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field's production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company's Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The line showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable. Surveys with Refraction Seishograph and Torsion Balance A reported oil show in a water well drew attention to the lands of the Belle Helene

Jan 1, 1943

By J. Brian Eby, T. I. Harkins

This paper outlines the geophysical investigation of the area covering the Darrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The Darrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook1 and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outline and comes to within about 4625 ft. of the surface. At this depth the diameter of the salt plug is approximately 4800 ft. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field's production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company's Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The line showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable. Surveys with Refraction Seishograph and Torsion Balance A reported oil show in a water well drew attention to the lands of the Belle Helene

Jan 1, 1943

By Paul H. Johnson

Chemical mining may be defined as the use of chemicals in extracting metal values from in situ broken or unbroken ores within a mine. The present means for the generation and regeneration of sulfuric acid or sulfuric-ferric sulfate solutions are inadequate for most applications. This report describes a pressure oxidation process for the generation and regeneration of these solutions from pyrites and spent iron sulfate leach liquors. While recent mining developments such as solution injection, caving, and conventional and nuclear blasting, have provided new and better means for the per-colation of leach solutions through rock masses, little has been done to reduce cost and improve the quality of the leach solutions that are required. A leach solution for chemical mining should meet certain requirements. It should be 1) inexpensive on either a small or large tonnage basis, 2) capable of selectively leaching the desired ore minerals contained in a particular ore, 3) of the proper strength or quality to do the job of leaching in an underground environment and 4) amendable to simple and inexpensive metal recovery steps. It is also important that the capital investment be low for the solution generation and; or regeneration plant.

Jan 8, 1965

D. M. Riordan has been appointed a member of the Institute Com¬mittee of the Engineers' Reserve Corps movement. Our Committee, therefore, now consists of Henry S. Drinker, Chairman, Messrs. Arthur S. Dwight, Warren A. Wilbur and D. M. Riordan.

Jan 1, 1916

Jan 1, 1948

Jan 1, 1948

By H. P. Allen

THE Achotla mill of the Cia. Minera de Pe[n]oles is of special interest in that it is one of the few still employing the chloridization process. The ore milled comes from the Suriana mine and consists of both oxide and sulphide, from neither of which can the gold or silver be extracted by a simple cyanide treatment. The mill was built in 1927, after several years of study in the development of the process1, and operated from December of that year until October 1930. Operations were resumed in February 1935, and have been continuous since, treating approximately 5000 tons per month, while the mine is getting up to full tonnage of 6500 tons per month. Transportation Of Supplies The property is in Guerrero, Mexico, some 175 km. by airline southwest of Mexico City. The mill site is at Temisco (Fig. I), 8 km. from the Balsas River and 4.8 km. by aerial tram from the mine. At Temisco are the general office, shops, warehouses and laboratory serving both mine and mill. Here sufficient water is available either from a small creek running through the property or from the Balsas River, also convenient and ample storage space for the tailings. With the exception of the mine timber and a few native building materials which may be obtained locally, all supplies for both mine and mill are brought down the Balsas River from Balsas, the terminal of a Mexican National Railway line out of Mexico City. The method of transportation on the river is interesting. Rapids with very fast water are numerous, prohibiting the use of mechanically propelled boats. Those used resemble large, flat-bottomed rowboats some 22 ft. long by 8 ft. wide (Fig. 2). They are manned by two oarsmen sitting in the bow, each handling one large oar, and usually another man in the stern who, with his oar, assists in steering the boat, especially when the rapids are run. From 3 to 7 tons of freight are carried on each boat, depending upon the stage of the water, which governs also the time

Jan 1, 1937

By H. E. Rorschach

Oil-field activities in Oklahoma made 1936 the best year since 1930. Approximately 2800 wells were completed, an increase of about 20 per cent over 1935. Purchasers' reports filed with the Corporation Commission showed a total of 200,240,252 bbl. of oil purchased from leases in 1936. The assembly of a complete table of the oil fields of the state was not achieved, as many of the early records of operators and pipe-line companies are not complete, and data for the older fields will perhaps never be fully tabulated. Table 1 includes all of the new fields and most of the important fields of the State of Oklahoma. The outstanding developments of the year were: the discovery of rich Wilcox-sand production in the Moore pool; the spectacular drilling campaign in the Capitol or Mansion extension in the Oklahoma City pool; the surprising extension of the Olympic pool and the Hunton lime zone in the Fitts pool; and the failure to find more Ordovician production in southern Oklahoma. Wildcat discoveries, which were on a par with 1935, resulted in the discovery of such promising pools as Billings-Wilcox, North Bethel, North Earlsboro and North Lucien. The Fitts-Upper Simpson, Edmond, Jesse, Keokuk Falls and South Burbank pools underwent considerable development. Fitts Pool.—The Fitts area in Pontotoc County was greatly extended during the year and was the leader in drilling activity in the state. The producing limits were pushed to the east and north and the development of the Hunton lime horizon was outstanding. In the Upper Simpson zone 162 wells were completed; 137 in the Hunton lime zone and 26 in the Wilcox zone. The Oil Creek zone, a sand body below the Wilcox member, was discovered by the Magnolia-Statler No. 3 well located in the 1/4. 1/4 of sec. 28-2N.-7E. Moore Pool.—The Moore pool, in Cleveland County, which was opened in 1935 by the Sinclair Prairie-Franklin Community No. 1 well, surprised the oil industry when the Sinclair Prairie-Marvel No. 1 well, on Apr. 1, 1936, discovered a rich body of Wilcox sand below the distillate

Jan 1, 1937

By George Krauss, M. Cohen

The reverse martensitic transfomzation (i.e., the conversion of martensite to austenite on heating) was investigated in Fe-Ni alloys containing 30.5 to 33.5 wt pct Ni. The reversed austenite was found to be sufficiently distorted to exhibit marked differences in mechanical properties and to undergo recovery and re crystallization on further heating. In particular, the yield strength of the reversed austenite was as much as 2.5 times higher than that of the virgin austenite: with five cycles of the direct and reverse martensitic transformation, the yield strength was 2.6 times higher. There was an accompanying decrease in strain-hardening capacity and in stable ductility or uniform elongation. The recrystallization was observed to follow sigmoidal kinetics, but was characterized by an abnormal1y large temperature dependence which was evidently due to carbon segregation at the migrating grain boundaries. Upon recrystallization, the strength Properties reverted to those of the virgin austenite, but the ductility did not fully recover until the annealing temperature was further raised to dissipate the carbon segregation at the grain boundaries. The transformation of reversed austenite to produce second-generation martensite resulted in an unusually imperfect structure, thereby leaditg to additional strengthening. Horlleuer, the martensitic phase was much less responsive in this respect than was the austenite. MOST martensitic transformations are capable of undergoing a reverse transformation back to the austenitic phase on heating.&apos; This reaction, like the direct transformation to martensite on cooling, is usually athermal. In analogy with the Ms andMf temperatures for the martensitic transformation (where M, > Mf), the reverse transformation is characterized by the As andAf temperatures (where As<Af). It is well-known that the finish (Af) of the martensite-to-austenite reaction on heating may occur at a temperature where austenite is not stable relative to other phases in the equilibrium diagram.&apos; Reverse martensitic transformations have been found to influence the properties of the parent austenitic phase in a number of ferrous alloys. The austenite thus produced after one or more reversals is significantly altered in strength, microstruc-ture, diffusivity, and annealing characteristics compared to well-annealed, virgin austenite. The first detailed observations of such phenomena were made by Wasserman3 on an Fe-30 wt pct alloy. He found that the reversed austenite (i.e., austenite formed by the reverse martensitic transformation) was much stronger than the original austenite, and the second-generation martensite (i.e., martensite produced from the reversed austenite) was somewhat stronger than the first-generation martensite. On heating the reversed austenite, recrystallization occurred in a manner similar to that of a cold-worked metal; the Laue spots sharpened and the strength decreased.4 In recent years, Russian workers have shown considerable interest in these reverse martensitic transformations. Most of such investigations5-10 have been concerned with the stabilization of reversed austenite relative to subsequent martensitic transformation, and because of its unusual nature, this phenomenon will be discussed in detail elsewhere." On the other hand, the annealing behavior of reversed austenite and the attendant variation in properties have received little attention beyond the experiments of Wasserman.3,4 Gridnev eta1.,8 in one of the few such studies. followed the hardness change of reversed austenite as a function of time at three annealing temperatures. The marked strengthening of austenite achieved by the reverse martensitic transformation has been referred to as "transformation strengthening" by Wasserman3,4 and as "phase hardening" by Malyshev et a1.7,9,10 to differentiate it from hardening produced by cold working. Both groups of investigators noted that further strengthening of the austenite could be attained by repeated or cyclic transformations, but the first cycle resulted in the most pronounced effect. Evidence of the altered microstructure of reversed austenite has been reported by Maximova and Nikonorova6 and by Edmonson and KO.12 The former found that reversed austenite was much more sensitive to etching than the original austenite, and the latter authors observed a (&apos;ghost" structure resembling martensite in certain areas of the reversed austenite. Enhancement of the self-diffusion rate in reversed

Jan 1, 1962

By Laurence Delisle, Arron Finger

The alloys formed by the addition of nickel to iron by conventional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.$ owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect coulcl be obtained in alloys of iron and nickel prepared by powder metallurgy technique. Procedure Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating Co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, o.oo15; lead, 0.035; tin> 0.025; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A repre-sentative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 325-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the sur-faces of the particles. The reduced pow-ders, slightly caked, were ground in a mortar and screened again through a 325-mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hy-draulic presses. The pellets were com-pacted in a cylindrical die, 34-in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specified for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By Arron Finger, Laurence Delisle

The alloys formed by the addition of nickel to iron by conventional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.$ owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect coulcl be obtained in alloys of iron and nickel prepared by powder metallurgy technique. Procedure Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating Co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, o.oo15; lead, 0.035; tin> 0.025; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A repre-sentative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 325-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the sur-faces of the particles. The reduced pow-ders, slightly caked, were ground in a mortar and screened again through a 325-mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hy-draulic presses. The pellets were com-pacted in a cylindrical die, 34-in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specified for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By J. P. Hirth, C. S. Hartley

A simple graphical technique is presented for rapidly determining the ratio of resolved shear stress on slip systems in single crystals to the applied stress (Schmid factor) for various simple states of stress. Master plots are presented which, when used in conjunction with an appropriate stereo-graphic projection, allow one to determine the Schmid factor for all slip systems in a crystal of given orientation. It is shown that one such plot suffices for simple tension or compression, flex-ural bending, and biaxial compression, while a combination of two different plots must be used for torsion and simple shear. STUDIES of the deformation behavior of single crystals are most valuable when the applied stresses are resolved onto the various slip systems of the crystal. A careful study of the available slip systems and proper selection of the state of stress used and the specimen orientation can then yield quantitative information about the probability of specific dislocation reactions, the strength of barriers to plastic flow, and the mechanisms of yielding and flow in general. It is the purpose of this work to analyze some common states of stress used in deformation studies and to present a simplified way of determining for these cases the ratio of the resolved shear stress on the slip systems to the applied stress (Schmid factor). I) CALCULATIONS We first define two orthogonal coordinate systems: one based on the specimen geometry (a right circular cylinder of radius, R, is considered here) and one based on the particular slip system of interest. The unit vectors and angles specifying the two coordinate systems and the relationship between them are listed in Table I. The relationships among the various angles and unit vectors are shown on a stereographic projection in Fig. 1. The transformation matrix between the (XI X2 X3) and (x&apos;1 x&apos;2 x&apos;3) system is x1 x2 x3 X&apos;1 a11 al2 a13 x&apos;2 a21 a22 a23 x&apos;9 a31 a32 a33 where in this case the direction cosines aij are given by a11 a12 a13 aij = a21 a22 a23 a31 a32 a33 sin 0 cos F cos 0 sin F cos 9 = -cos 0 cos F sin 0 sin F sin 6 [1] 0 -sin F cos (p In terms of Eq. [I.], the stresses sij, referred to the slip system, are determined from oij, referred to the specimen axes, by1,2

Jan 1, 1965