Search Documents

By James E. Lawver

A SURVEY of Minerals Beneficiation Div. membership indicated genuine interest in automatic process control, but revealed that the average mill is operating with a minimum of self-regulating devices. Apparently, the mill operators are content to continue without controls until the practicality of self-regulating devices is more generally accepted, or, in the opinion of the writer, until automatic controls become a necessity to meet economic demands of product quality and cost. Both to stimulate interest in control, and to solicit publication of technical know-how by members and equipment manufacturers, this paper presents a cross section of control problems in two general categories: (a) Control problems that can usually be solved by reference to the literature, i.e. controls that have proven successful in the mineral or chemical industries; (b) Problems that are troublesome and frequently unsolved due to unavoidable adverse conditions in the mill circuit to be controlled.

Jan 10, 1953

By G. R. Leverant, C. P. Sullivan

Re crystallized TD-nickel mi-2Th0,) in both coated und uncoated conditions was fatigued at 1800°F at total strain ranges varying .from 0.2 to 0.75 pct. The fatigue life of uncoated inaferal, Nf, was related to the total strain range, ?eT, by (2Nf/021AeT = 0.014. A duplex Al-Cr pack coating increased the fatigue life by about a factor of two. The cracks that led to failure in both coated and uncoated material were initiated at the outer surface, indicating that the mechanical properties of the surface layers were important in determining fatigue life. Crack propagation and subsurface crack initiation in the TD-nickel occurred preferentially at grain boundaries with cavitation at thoria particle-matrix interfaces an integral part of the grain boundary fracture process. The importance of both the grain morphology developed during thermome chanical processing of TD-nickel and the distribution of thoria particle sizes to fatigue resistance are discussed. THE fatigue properties of only a few dispersion-strengthened metals have been studied at temperatures 0.5 Tm;1,2 among these have been lead and aluminum containing oxide dispersions. TD-nickel is a material of interest for application in aircraft gas turbine engines, but little fundamental information is available on its behavior under cyclic loading conditions. In this study, the low-cycle fatigue properties of TD-nickel were determined at 1800°F with emphasis on the 101-lowing; 1) the relation of the grain morphology produced during thermomechanical processing to crack initiation and propagation; 2) the role of thoria parti-cles in the fracture process; and 3) the effect of an oxidation resistant coating on fatigue life. I) MATERIAL AND EXPERIMENTAL PROCEDURE The TD-nickel was supplied by DuPont as a 5/8-in. thick plate which had been subjected to a proprietary series of thermomechanical treatments with a final anneal at 2000°F for 1 hr in hydrogen. The composition of the material is given in Table I. At the test temperature of 1800°F, the 0.2 pct offset yield stress was 15,000 psi, and the elongation and reduction in area were 4.6 and 3.0 pct, respectively. The microstructure of this material has been previously described.&apos; Briefly, it consists of an array of lath-shaped grains, about 0.15 mm in thickness, with the long dimension of each grain parallel to the primary working direction, Fig. 1(a). The presence of very small annealing twirls, Fig. l(b ), together with the absence of extensive dislocation networks, Fig. L/C), indicated that the material was in the recrystal- Table I. Composition of TD-Nickel ThO2 2.3 vol pct C 0.0073 wt pct lex 0.01 wt pct Cr 0.01 wt pct Cu 0.004 wt pct S 0.001 wt pct Ti <0.001 wt pct Co <0.01 wt pct Ni bal lized condition. Commercial TD-nickel sheet has a similar grain size and shape, but unlike the present material is not recrystallized as evidenced by the absence of annealing twins and the presence of a well-developed dislocation substructure.4 The plate material had Young&apos;s moduli in the rolling direction of 22 x 106 psi and 13 x 106 psi at room temperature and 1800°F, respectively, indicating a texture with a strong {100}<001> component in agreement with previous observations on recrystallized TD-nickel sheet.596 The 2.3 vol pct of thoria particles were uniformly distributed although some clustering and stringering of larger particles was occasionally seen. The average diameter of the particles was 450 and the calculated mean planar center-to-center spacing was 2100Å. Two specimens were coated with a duplex A1-Cr pack coating. The coating was somewhat nonuniform from one position to another along the gage length. An area of the coating after testing is shown in Fig. 2. Electron microprobe analysis revealed the following zones in the various lettered regions indicated in Fig. 2: A) a bcc matrix of B-NiA1 with some chromium in solid solution along with a fine dispersion of a chromium-rich second phase which was probably precipitated during cooling from the test temperature to room temperature; B) fcc y&apos;-Ni,Al with some chromium in solid solution; C) porosity; D) a two-phase mixture of a chromium-rich solid solution containing nickel and aluminum and a small volume fraction of a nickel-rich solid solution having approximately the same composition as the immediately adjacent portion of region E, E) the TD-nickel substrate containing chromium in solid solution to a depth of 5 to 10 mils. As expected from the nature of the diffusion processes involved,7 the thoria particles were present only up to the layer of porosity, region C, Fig. 2. The measured thickness of the coating proper, zones A to D, after testing was 1 to 2 mils. The specimen design and testing techniques have been previously discussed.&apos; Stressing was axial and parallel to the lath-shaped grains (i.e., parallel to the rolling direction). The total strain range was controlled between zero and a maximum tensile strain varying from 0.2 to 0.75 pct. (The test at 0.2 pct total strain range was switched to load control at 1030 cycles at which point the peak tensile and compres-

Jan 1, 1970

By Rex B. McLellan

Studies of the eyuilibrzum between ferrite and austenite with gas mixtures (CO + CO2 and H2 + CHe) have been used as a means of deducing the energy and vibrational entropy of carbon atoms in dilute interstitial Fe-C solutions. A simple model for dilute interstitial solutions is given which enables a solubility equation for the equilibrium between the gas mixtures and the solid to be deduced. This solubility equation is used to estimate the partial In this work measurements of the equilibrium between dilute solid solutions of carbon in iron and gaseous mixtures of CO2 + CO and CH4 + Hp have been analyzed using theoretical solubility equations deduced from a knowledge of the thermodynamic parameters of the gas mixtures and an appropriate model for the solid solution. The solubility equations are deduced by equating the chemical potential of carbon atoms in the gas thermodynamic functions of dilute Fe-C solutions from the measured equilibrium between the solid and the gas mixtures. It is shown that the vibra-tional entropy of a carbon atom in a and y iron is smaller than the corresponding entropy 01. a nitrogen atom in solid solution inferrite or austenite and that there is little difference between the vibrational entropies of both nitrogen and carbon atoms in ferrite and austenite. and solid phases. The chemical potential of carbon in the gas is found from a simple statistical mechanical analysis of the gas mixtures utilizing spec-troscopic data while that for carbon in the interstitial solution is found from a model in which the carbon atoms act as bound oscillators distributed in a random fashion in the solution. The solid solution is dilute enough to enable solute-solute interactions to be ignored. Thus the configurational entropy of the solution is ideal but the mixing entropy contains additional excess terms due mainly to the vibrational changes occurring on solution formation. The partial excess entropies (and the partial energies) do

Jan 1, 1965

This brief resume of events, transpiring in Mexico, culled from the daily New York newspapers, since the last Bulletin went to press, does not indicate any degree of improvements in the situation. GENERAL ALVAREZ COURTMARTIALED AND SHOT General Francisco Alvarez of the anti-Government forces was captured in the battle in which General Aureliano Blanquet, Minister of War in the Huerta Cabinet, was killed, and was sentenced by a courtmartial and shot in spite of a specific order of the Supreme Court in Mexico City that the execution should not take place. General Alvarez was a member of the staff of Felix Diaz, and was a veteran of the old regular army of Mexico. MEXICO WILL NOT RECOGNIZE MONROE DOCTRINE Failure of the Allied Powers to invite Mexico to participate in the conference of neutrals at Paris aroused President Carranza to bitter resentment, which was enhanced by the incorporation of recognition of the Monroe Doctrine in the covenant of the League of Nations without consultation with Mexico. Statements were issued by the Mexican Foreign Office disavowing adherence to the Monroe Doctrine and announcing the withdrawal of the Mexican representative in France. Carranza had been awaiting an opportunity to get his agent away from Paris for the real reason that he had been unable to secure recognition from either the French or the British Government. Mexico announces, says the New York Times editorially, that "she has not recognized and will not recognize the Monroe Doctrine." "Nobody has asked her to recognize the Monroe Doctrine," continues the editorial. "The enforcement of the principles enunciated by President Monroe does not depend upon Mexico, upon anybody&apos;s recognition or non-recognition. The countries concerned in the Monroe Doctrine are the United States on the one hand, and countries not of this hemisphere on the other."

Jan 6, 1919

[Aase, Qlenn D., (Junior Member &apos;40) Jr. Met.. American Smelt. & Refin. Co., Selby. Calif. Abadie, Henry G., (Junior Member &apos;43) Petr. Engr.. Avenal, Calif. Abbott, Clarence E., (Member &apos;04) Civil En=.. V.P.. Tennessee Coal. Iron & R.R. Co., 1542 Brown biarx Bldg.. Birminpham, Aln. Abbott. Fred E., Jr., (Member &apos;44) Petr. Engr., C/O Arabian Anierican Oil Co.. A.P.O. 816. c/o Postmaster, New York, N. Y. Abel, Raymond L., (Member &apos;28) Chem. Engr.. C. O., Pittsburgh Chem. Warfare Procurenlent Dist.. American Bank Bldg., Pittsburph. Pa. Abel, Walter D., (Member &apos;32) Min. Engr.. Supvr. Engr.. RFC, Los Angeles, Calif.]

Jan 1, 1946

By J. M. Floyd

The theory, construction and applications of oxygen sensors employing high-temperature electro- chemical cells with solid electrolytes are briefly reviewed. The application of disposable probes to measurement of the oxygen potential in matte and slag baths in tin, copper, and nickel smelting operations is described. Examples discussed include end-point determination in smelting and slag-cleaning operations, pilot-scale investigations of process chemistry to assist in the development of smelting strategies, and measurements in operating smelters to improve the efficiency of operation.

Jan 1, 1984

[Secretary&apos;s Note.—The following official tables, prepared by the government of the State of Nuevo Leon, and presented to the Institute at the fifth seseion of its Mexican meeting, held at Monterrey, November 26, 1901, present in compact form a general summary of the mineral and metallurgical industry of the State for the preceding calendar year, together with a statement of the railway-shipments of ores from January 1 to October 31, 1901, which, in the absence of direct official mining and metallurgical statistics (not yet available for that year), clearly indicates an increased activity and productiveness of these industries. In other words, the mines are reported to have yielded in 1900 a total product of 83,960,169 kilos of ore; whereas, the railway is reported to have carried, in 10 months of 1901, a total of 108,318,647 kilos of ore. At this rate, the railway-shipments for 1901 mould amount to nearly 130,000,000 kilos. It is, of course, possible that the railwaystatistics include other freight than ores, or that they include duplications, such as would be involved in the record, first of certain ores transported, and afterwards of the " base bullion " produced therefrom. An accurate comparison is therefore impossible ; yet, after making all reasonable allowances for such items as have been named, it seems safe to infer that the mining and metallurgical industry of this State accomplished in 1901 a substantial progress.]

Jan 1, 1902

Herewith are transmitted the joint report of the Treasurer and Finance Committee for 1934 and the reports for the same year of the Chairmen of the following Committees: Admissions, Membership, Papers and Publications, Library, and MINING AND METALLURGY. TO these reports you are referred for details of the year&apos;s activities. Finances.-Income for 1934 from all sources totalled $134,967 com- pared with $121,689 in 1933. The increase is accounted for principally by four items: $6000 increase in initiation fees and dues of new members; $1800 in current dues; $4000 in "back" dues; and $2800 in the sale of publications, including TRANSACTIONS volumes and technical papers in the form of "separates." In passing, it may be remarked that income from back dues during 1935 will be less than in 1934, for the obvious reason that the total amount of dues in arrears has shrunk and consequently there is less to draw from. Income from

Jan 1, 1934

By David A. Rice

This note describes a simple, rapid technique for measuring the apparent volume and density of individual bits of porous materials such as iron ore pellets or pieces of coke. The method consists of determining the weight recorded on a balance when a particle is depressed below the surface of mercury, and calculating the apparent volume from the known density of mercury. The apparent density is calculated after weighing the particle in air. The method is particularly well suited for applications where a great number of determinations are to be made. An additional benefit is the minimal handling of the mercury. In any event, the usual recommended safety precautions should be adhered to.

Jan 1, 1982

By William E. Ford, Edward Salisbury Dana

URANINITE. Cleveite. Broggerite. Nivenite. Pitchblende. Isometric. In octahedrons (o), also with dodecahedra1 faces (d) ; less often in cubes with o and d. Crystals rare. Usually massive and botryoidal; also in grains; structure sometimes columnar, or curved lamellar. Fracture conchoidal to uneven. Brittle. H. = 5&apos;5. G. = 9&apos;0 to 9&apos;7 of crystals; of massive altered forms from 6&apos;4 upwards. Luster submetallic, to greasy or pitch-like, and dull. Color grayish, greenish, brownish, velvet- black. Streak brownish black, grayish, olive-green, a little shining. Opaque. Comp. -A uranate of uranyl, lead, usually thorium (or zirconium), often the metals of the lanthanum and yttrium groups; also containing the gases nitrogen, helium and argon, in varying amounts up to 2&apos;6 p. c. Calcium and water (essential?) are present in small quantities; iron also, but only as an impurity. The relation between the bases varies widely and no definite for- mula can be given. Radium was first discovered in this mineral and it has been shown that it and the helium present are products of the breaking down of the uranium.

Jan 1, 1922

By David B. Reger

The year 1935 was mostly quiet in West Virginia, and devoted to routine drilling in old pools and extensions. A notable exception to this general rule, however, was the further development and proving of a field of gas discovered in 1930 in the deep Oriskany sand (L. Dev.) in Kanawha County, as later discussed. No new pools of oil were found and little or no attempt was made to search for them. No new pools of gas were recorded but various extensions of old pools were made. There were no new pipe line extensions of consequence, either for oil or gas. Operating technology was much the same as in recent years, there having been some further advances in repressuring oil wells and in the use of acid for treating small wells in calcareous formations, and some change in the technique of shooting gas wells. Financially, there has been a full market for all crude oil produced and a fair market for gas. There have been occasional transfers of producing oil or gas properties, mainly between established companies. Most of the attempts made to finance mergers and new developments have failed largely because of difficulties encountered under the Federal securities act. This situation has prevented the normal turnover of properties by small operators who frequently desire to sell partly developed interests and then step out into new ventures. New Development In 1935 the State issued 569 permits for drilling and records the same number of completions. One trade journal records 533 completions and another 483. A running record kept by the writer accounts for 713 completions, with 156 oil wells, 417 gas wells and 140 dry holes (Table 3). Some of these completions may be old wells drilled to deeper sands. Some, apparently, have been drilled without legal permit. Extensions of Producing Areas Ritchie County has again led all others in new drilling, with 137 completions as compared to 74 in Calhoun and 61 in Cabell. This Ritchie County drilling was done mainly to extend or further develop old pools

Jan 1, 1936

By David B. Reger

The year 1935 was mostly quiet in West Virginia, and devoted to routine drilling in old pools and extensions. A notable exception to this general rule, however, was the further development and proving of a field of gas discovered in 1930 in the deep Oriskany sand (L. Dev.) in Kanawha County, as later discussed. No new pools of oil were found and little or no attempt was made to search for them. No new pools of gas were recorded but various extensions of old pools were made. There were no new pipe line extensions of consequence, either for oil or gas. Operating technology was much the same as in recent years, there having been some further advances in repressuring oil wells and in the use of acid for treating small wells in calcareous formations, and some change in the technique of shooting gas wells. Financially, there has been a full market for all crude oil produced and a fair market for gas. There have been occasional transfers of producing oil or gas properties, mainly between established companies. Most of the attempts made to finance mergers and new developments have failed largely because of difficulties encountered under the Federal securities act. This situation has prevented the normal turnover of properties by small operators who frequently desire to sell partly developed interests and then step out into new ventures. New Development In 1935 the State issued 569 permits for drilling and records the same number of completions. One trade journal records 533 completions and another 483. A running record kept by the writer accounts for 713 completions, with 156 oil wells, 417 gas wells and 140 dry holes (Table 3). Some of these completions may be old wells drilled to deeper sands. Some, apparently, have been drilled without legal permit. Extensions of Producing Areas Ritchie County has again led all others in new drilling, with 137 completions as compared to 74 in Calhoun and 61 in Cabell. This Ritchie County drilling was done mainly to extend or further develop old pools

Jan 1, 1936

By Stuart E. Buckley, C. R. Hocott

The viscosity of the oil in the reservoir is one of the properties that influence its movement through the sand to producing wells. Measurements of viscosity, therefore, are pertinent to problems associated with well behavior and with the estimation of recoveries, and afford an indirect means for partial evaluation of various methods of controlling reservoir behavior. The effect of dissolved gases on the viscosity of crude oil has been determined,ls2 but no data have been published on the viscosity of representative samples of reservoir oils. This paper describes a simple instrument that has been used to determine the viscosities of a number of subsurface oil samples at the temperatures and pressures existing in the reservoirs, and presents the results of the determinations for typical fields. Construction oF the Apparatus The principal requirements of any instrument used for the examination of subsurface samples are that it be strong and simple both in design and in method of operation. Accuracy beyond that of the degree of reproducibility of subsurface Sam-~les from various wells in a reservoir or exceeding that of the common measure-merits of reservoir temperatures and Pressures is not required. Because of the expense of procuring subsurface samples, it is necessary also that the instrument operate on a relatively small fraction of a sample, leaving the remainder for other tests, and that there be few or no failures of the equipment to cause undue delay or loss of a sample. After preliminary experiments with a falling bullet, the results of which were not satisfactory, a simple viscosimeter was built of the rolling ball type first proposed by Flowers3 and later used by several investiga-tor. 5.8 The apparatus consists essentially of a removable, accurately bored cylindrical barrel of 1/4-in. nominal internal diameter, 8 in. long, in which a closely fitting steel ball rolls through the oil with the barrel inclined at a definite angle. The ball makes contact at one end of the barrel with ail insulated electrode, closing an electrical circuit, which actuates a buzzer. The meas-urements consist essentially in determining the time required for the ball to travel the length of the barrel. The details of the construction are shown in Fig. I. The barrel in which the ball rolls was made from a section of 25-caliber blank rifle barrel, specially bored to an exact uniform diameter and polished. The barrel slides snugly into a hole bored in a solid stainless-steel cylinder, an upper external shoulder of the barrel compressing a small spring, and is held in place by a hollow nut. The spring prevents the barrel from seating against the bottom of the bored hole in the cylinder, while narrow external longitudinal slots in the barrel permit fluid to flow around it and through the bottom. The upper part of the recess in the steel cylinder is enlarged to form a tapered chamber, which acts as a reservoir for the oil and affords space for agitation to ensure

Jan 1, 1941

By C. R. Hocott, Stuart E. Buckley

The viscosity of the oil in the reservoir is one of the properties that influence its movement through the sand to producing wells. Measurements of viscosity, therefore, are pertinent to problems associated with well behavior and with the estimation of recoveries, and afford an indirect means for partial evaluation of various methods of controlling reservoir behavior. The effect of dissolved gases on the viscosity of crude oil has been determined,ls2 but no data have been published on the viscosity of representative samples of reservoir oils. This paper describes a simple instrument that has been used to determine the viscosities of a number of subsurface oil samples at the temperatures and pressures existing in the reservoirs, and presents the results of the determinations for typical fields. Construction oF the Apparatus The principal requirements of any instrument used for the examination of subsurface samples are that it be strong and simple both in design and in method of operation. Accuracy beyond that of the degree of reproducibility of subsurface Sam-~les from various wells in a reservoir or exceeding that of the common measure-merits of reservoir temperatures and Pressures is not required. Because of the expense of procuring subsurface samples, it is necessary also that the instrument operate on a relatively small fraction of a sample, leaving the remainder for other tests, and that there be few or no failures of the equipment to cause undue delay or loss of a sample. After preliminary experiments with a falling bullet, the results of which were not satisfactory, a simple viscosimeter was built of the rolling ball type first proposed by Flowers3 and later used by several investiga-tor. 5.8 The apparatus consists essentially of a removable, accurately bored cylindrical barrel of 1/4-in. nominal internal diameter, 8 in. long, in which a closely fitting steel ball rolls through the oil with the barrel inclined at a definite angle. The ball makes contact at one end of the barrel with ail insulated electrode, closing an electrical circuit, which actuates a buzzer. The meas-urements consist essentially in determining the time required for the ball to travel the length of the barrel. The details of the construction are shown in Fig. I. The barrel in which the ball rolls was made from a section of 25-caliber blank rifle barrel, specially bored to an exact uniform diameter and polished. The barrel slides snugly into a hole bored in a solid stainless-steel cylinder, an upper external shoulder of the barrel compressing a small spring, and is held in place by a hollow nut. The spring prevents the barrel from seating against the bottom of the bored hole in the cylinder, while narrow external longitudinal slots in the barrel permit fluid to flow around it and through the bottom. The upper part of the recess in the steel cylinder is enlarged to form a tapered chamber, which acts as a reservoir for the oil and affords space for agitation to ensure

Jan 1, 1941

By William P. Blake

Copper Basin in Yavapai county, Arizona Territory, about twenty miles southwest of Prescott, is well named. It is a depressed area, and a region of cupriferous impregnation.* The geologic conditions are simple. The foundation rock is a coarse-grained granite and gneiss, in which soda feldspar predominates. There are also dykes of porphyritic rock, and a large quartz vein containing pyrites. Superimposed on this crystalline foundation, we find heavy beds of mechanically formed rocks, conglomerates, breccias, and sandstones, in horizontal layers cropping along the bed of a creek, and apparently the remnants of a much more extended formation, now denuded and largely carried away by gradual atmospheric erosion. The heavy beds of conglomerate are in many places much broken and tilted up, even standing on edge in large blocks, as if they had been lifted by some great convulsion; but the cause is much more simple, being merely the removal by gradual disintegration and erosion of the softened and decayed granitic rock below. The materials of these sedimentary beds are chiefly fragments of granite, gneiss, and plutonic rocks loosely mingled. They are the chief repositories of the copper-ore, which forms the cementing substance. This copper-ore is the blue and the green carbonate, azurite and malachite, and the ore is so generally spread through the mass of the beds that the blue and the green croppings can be seen at a great distance, particularly after or during a shower of rain, when the colors are extremely brilliant and beautiful. The copper carbonate is not only a matrix and a cementing material for the fragments of rock, but it invests and covers these fragments so that only malachite and azurite are visible. The beds are from three to ten feet or more in thickness, and, although seemingly solid carbonate of copper, rarely contain over 12 or 15 per cent. of that metal. Some portions of the conglomerates are much more highly charged with copper than others, and in places the beds are almost without copper. If a lump of the coarse sandstone

Jan 1, 1889

By Winston A. Wong, John J. Jonas

Commercial purity aluminum was deformed by extrusion over the temperature range 320° to 616°C and the strain rate range 0.1 to 10 per sec. Flow stresses and strain rates were calculated from the experimenLa1 ram pressures and speeds. The stress-strain rate-lemperature relationship in extrusion was found to be similar to that in creep. Extrusion, torsion, compression, and creep data extending over ten orders of magnitude of strain rate and over two orders of magnitude of stress were correlated by a single creep equation. It was concluded that hot-working is a thermally activated process, in which the rate-controlling mechanism is either the climb of edge dislocations or [he motion of jogged screw dislocations. The microstructural changes observed during extrusion were consistent with the proposed deformation mechanisms. ALTHOUGH great progress has been made in understanding the technology of extrusion, very little is known about the actual deformation mechanisms operating during flow. Previous accounts describing extrusion have indicated that the relationship between ram speed (V), pressure (P), and temperature (T) can be given as follows:1 V = apb and P = A&apos; exp(-AT). In these equations, a and b are constants which depend on temperature, A&apos; is a constant which depends on ram speed, and A is a "coefficient" with a different value for each metal. Although these equations have fairly wide application, they do not contribute much to a fundamental understanding of the deformation. Furthermore, extrusion has not hitherto been considered as a thermally activated rate process. This lacuna is surprising because hot-working is similar to high-temperature creep in several respects. There is, in fact, a fair body of experimental evidence suggesting that the material response under hot-working conditions is similar to that occurring under creep conditions, in spite of the many orders of magnitude difference in strain rate.2"4 Since creep has been extensively analyzed in terms of dislocation mechanisms, the comparison of hot-working to creep is useful, for it can suggest the possible deformation mechanisms operating during hot-working. In this paper, the hot extrusion of aluminum will be examined from the point of view of thermally activated deformation mechanisms, such as operate during creep. EXPERIMENTAL PROCEDURE The experimental procedure consisted of extruding commercial purity aluminum* over a range of ram velocities and temperatures at constant die reduction by the direct method. Details of the experimental equipment have been published elsewhere.5 Extrusion was carried out at each of the following billet temperatures: 320°, 376°, 445°, 490°, 555°, and 616°C at the following constant ram speeds: 0.002, 0.008, 0.02, 0.1, and 0.2 in. per sec.* All results were obtained using a square-shouldered die with an extrusion ratio of 40:1, giving a reduction in area of 97.5 pct. The ram force was the dependent variable, and was measured by means of strain gages on the ram and was plotted as a function of ram travel. The sequence of events before making an extrusion was duplicated before each run so as to minimize as much as possible variations in experimental conditions. For example, after the equipment had been assembled, the billet was allowed to heat up to temperature inside the insulated container. Once the container attained the desired temperature, a period of 1/2 hr was allowed to elapse before the extrusion was made. This time was found to be required to allow the billet to reach a steady-state temperature, as determined from previous tests. When all was ready, extrusion was carried out without interruption; that is, the billet was upset and extruded in one operation. EXPERIMENTAL RESULTS AND DISCUSSION The two usual experimental approaches for investigating high-temperature deformation exhibit an important common feature. In the first approach, which corresponds to creep, a constant stress (or load) is applied to the material at constant temperature and the resultant strain is recorded against time. After an initial transient stage, a state of constant strain rate exists (secondary creep), in which a steady-state condition is established which is sensitive to variation in either applied stress or temperature. In the second approach, a constant strain rate is applied and the resultant flow stress is recorded. This corresponds to the situation in hot torsion or hot compression, where it is observed that, for a constant test temperature, there is an initial rise in stress to a steady value which is maintained up to very high strains. In tests of this type, a steady-state region is also established in which the stress is sensitive to variation in either the strain rate or the temperature.3,4,6-16 In both types of tests, therefore, a steady-state region is established after an initial transient. In the case of hot-working this region may be called steady-state hot-working, and it is analogous to steady-state creep with which it has many common features. Stress Dependence of the strain Rate in Extrusion. In order to assess the stress dependence of the strain rate under extrusion conditions, and to compare it to that of creep, as well as of hot torsion and hot compression, the extrusion data were analyzed according to power, exponential and hyperbolic sine creep equations.

Jan 1, 1969

By Francis Foley

IN examining steel under the microscope, one is constantly confronted with structures that are difficult to interpret. Recently, in a collection of samples for exhibition purposes, the writer found apiece of open-hearth runner metal, 2 in. (50 mm.) in diameter, that had been fractured for use as a sample of cast-steel structure. On polishing and etching a section for the purpose of photographing a field to typify the microstructure of steel in the "as cast" condition, a variety of structures was found (Fig. 1) so arranged as to arouse interest at once. For a distance of about 0.065 in. (1.6 mm.) from the skin of the runner, normal ingot structure was found (Fig. 2); this was followed by a zone, about 0.215 in. (5.5 mm.) wide, of considerably lower carbon content in which occurred a most pronounced Widmannstättian structure (Fig. 3); from this point on to the center of the runner, the metal was again of normal ingot structure (Fig. 4). Representative samples taken from the metal in the three zones showed the following analysis: C Ni Cr Metal from skin 0.34 1.26 0.63 Widmannstättian zone 0.21 1.18 0.63 Metal from center 0.34 1.32 0.67

Jan 7, 1919

By Robert D. Pehlke, Kazuhisa Okajima

The activity of zinc in dilute liquid lead alloys containing small additions of silver and gold has been measured using a multielectrode galvanic cell with a fused chloride salt electrolyte. The range of temperatures studied in the Pb-Zn-Ag system was 550" to 670°C and in the Pb-Zn-Au system was 680" to 800°C. The interaction parameters between zinc and the precious metals in the respective temperature ranges are ThE lead-rich corners of the Pb-Zn-Ag and Pb-Zn-Au ternary systems are of considerable industrial importance. The use of zinc additions for the desilvering The results of this investigation have Provided a senzi-quantitative determination of the liquidus phase boundaries in the lead-rich corner of these ternary diagrams. of liquid lead either by the Parkes process or by the more recent Williams continuous process is an important refining phase of lead production.1 Several in-ve~ti~ations~-~ have been carried out on the Pb-Zn-Ag system with the hope of improving the efficiency of refining lead in this manner. The addition of zinc also provides a means for separating gold from lead. Since gold is eliminated more easily than silver, a two-stage removal of gold and silver is possible.8&apos;7 The thermodynamic interactions between zinc and these precious metals in dilute solution in liquid lead

Jan 1, 1968

THE decision of the lower court (United States District Court for the Southern District of New York) in the suit of the Dwight & Lloyd Sintering Co., vs. John E. Greenawalt has been affirmed by the United States Circuit Court of Appeals for the Second Circuit. In the original suit, infringement of seven patents was alleged, these covering the process of producing a sinter .out of finely pulverized metalliferous ores as practised in shallow pans operating intermittently in distinction to the Dwight 6: Lloyd continuous machine. The court found that the long delay in bringing suit precluded any recovery of profits from the defendant under the basic down-draft sintering patent, although Dwight & Lloyd are recognized as the inventors of this&apos; contribution to the art and its .importance is acknowledged.

Jan 1, 1928

By Laurence Pellier

Electron microscopical studies were made of the effect of sensitization at 1200oF on a Type-.104 stainless steel with high carbon and low nitrogen and oxygen contents, after solution annealing and after cold working. The loci of the carbide precipitates in the early stages of sensitization were followed in dry stripped plastic replicas. Some observations were made by direct electron transmission on thinned films. Intragranular dislocations showed a high degree of stability through the annealing necessary to produce sensitization. I HE present work was undertaken to determine the effect of sensitization, at 1200°F, for 1/2 hr, on the electron microstructure of a Type-304 stainless steel with high carbon, and low nitrogen and oxygen contents, after solution annealing and after cold working. Many electron microscopical studies of sensitization of 18-8 stainless steels have already been made. Most of them utilized extraction replicas, from which the morphology and composition of the precipitated carbides could be established.&apos;-" ry stripped replicas were seldom used for such studies, although it was demonstrated that they are applicable, in general, to EurveYs of the general microstructure of many alloys&apos; and, in particular, to the observation of precipitated carbides in austenitic stainless steels.3

Jan 1, 1963