Search Documents

By James H. Bechtold

The yield strength of annealed tungsten was found to have a strain rate exponent 12 times as great as that of low carbon steel. The effects of temperature and strain rate could be correlated through the Zener-Hollomon parameter with a heat of activation associated with yielding of 32,000 cal per g-atom. This heat of activation is independent of strain although both the temperature and strain rate dependence of the yield strength vary with strain. MOST metals have mechanical properties that are relatively insensitive to strain rate, especially at temperatures below that at which creep is important. In iron and molybdenum," however, relatively large strain rate effects are observed in the temperature range where the rapid increase in yield strength occurs which leads to the ductile to brittle transition. In this temperature range Zener and Hollomon' have suggested that the effects of strain rate and temperature T on the yield strength could be correlated through a single parameter, P, in the following manner where Q is a heat of activation characteristic of the metal and associated with some unspecified relaxation process. They also observed that if the temperature is restricted to a relatively narrow range— below room temperature for steel—that the logarithm of the yield strength could be expressed as a linear function of the logarithm of P. From this relation the logarithm of stress should be a linear function of the logarithm of the strain rate at constant temperature: where r will be referred to herein as the strain rate exponent. At a constant strain rate the logarithm of stress should be a linear function of l/T, ay(e = C) ~ eT [4] where q = Qr [5] and is referred to herein as the temperature exponent. These equations have been found to relate the effects of temperature and strain rate on the yield strength of molybdenum in the temperature range wherein the ductile to brittle transition occurs, —75° to +150°C.2 Bechtold and Shewmon3 have shown recently that the ductile to brittle transition in annealed tungsten occurs in the temperature range +150° to +350°C. In this temperature range the yield strength in-

Jan 1, 1957

By J. R. Linney

APPROXIMATELY 5,788,000 long tons of crude ore was produced by the Eastern magnetite industry in 1946, or a drop of 26 per cent compared -with 1945. Decrease in production -throughout the industry varied from :8 per cent for the mine with the lowest reduction to 49 per cent for the mine -with the highest reduction. At the Chateaugay mine, operated by :the Republic Steel Corp. at Lyon Mountain, N. Y., 426,900 long tons of crude ,ore was produced, yielding 129,500 long tons of concentrates or a reduction of 46 per cent compared with the previous year. Owing to a strike the mine was closed down from Jan. 21 to July 29. At the Mineville mines, also operated by Republic Steel, output was 755,000 long tons of crude ore or a reduction of 49 per cent compared with 1945. The yield from the crude ore production consisted of 51,500 long tons of lump ore and 380,000 long tons of concentrates. The Mineville plant did not operate from March 17 through July 28, on account of the strike. The Fisher Hill mine, which produced 93,000 long tons of crude ore, included in the above figures, has not operated since March 17, 1946.

Jan 1, 1947

By Arthur A. Center

AT the beginning of 1944 it was expected that the production of metallic zinc in the United States from domestic and foreign concentrates would exceed the 1943 figure though domestic production of concentrates was expected to drop below the 1943 rate, mostly in the Tri-State area. Imports of concentrates were estimated to more than take care of such deficiency. North American concentrate production, available for import to the United States or elsewhere during the year, was estimated at over 200,000 tons recoverable zinc content; South American at about 65,000 tons; Australian at about 50,000 tons. Production of both concentrates and metal in the United States, however, did drop, attributable in considerable part to man-power shortage in the industry. However production exceeded consumption, which fell off, and stocks of metal increased. These stocks have increased since the middle of 1942 but production and consumption are coming nearer to a balance. The A, B, and C premiums, which have played an important part in keeping up domestic production of concentrates, extend only to the middle of 1945 by present legislation. Congress is being asked for their continuance during the war and

Jan 1, 1945

By M. S. Klima, P. T. Luckie

Interfacing new or improved unit operations SUBMODULES with the EXECUTIVE of a macro analysis simulator usually requires modification of the input data. For example, particle processing SUBMODULES that are sufficiently general in nature to provide useful predictions require input data for rather narrow size fractions. Such data is not always available for the EXECUTIVE and must therefore be generated by the SUBMODULE. A successful interface to allow incorporation of a new SUBMODULE for comminution and one for classification in a general stream state flowsheet simulator is presented. The general nature of the SUBMODULES, as well as the logic of expanding and contracting the required data input is discussed.

Jan 1, 1983

By George Newton

When Mr. Bailey asked us to present a paper describing our new BOF shop, he requested that we avoid a presentation heavily laden with detail and statistics. Not only have we attempted to do this, but also we have prepared a number of colour slides which, hopefully, will provide you with a graphic conception of the facility. The installation of the BOF facility at the Steel Co. of Canada's Hilton Works was delayed many years because of the remarkable production growth of the oxygen open hearth furnaces in No. 3 shop. However, in mid-1960 it became strongly evident that not only would increased ingot capacity be required, but also that N0.2 shop - with vintage non-oxygen open hearth furnaces - would have to clean its stacks in the near future, or be closed down. A decision to embark on the BOF facility was made in 1967 after an extended period of in-depth planning and assessment of industry trends.

Jan 1, 1972

By J. B. Agan, R. J. Fernandes

This paper utilizes the layered-system approach, modified to include areal sweep efficiency, to determine the miscible-slug size required and to predict the perfort7zance of a miscible-slug process in a highly stratified reservoir having a permeability variation of 0.76. The slug size in each layer was determined from theoretical calculations and laboratory data which showed that, to maintain miscibility in the reservoir, the slug size had to be 8.2 per cent of the floodable hydrocarbon pore volume. Economic considerations, however, such as the value of the miscible product injected, the cost of injection and the cost of reprocessing the miscible product, limited the amount of miscible product which could be injected into the lower-permeability layers. This resulted in subjecting only 60 per cent of the reservoir to a slug size sufficient to maintain miscibility. Utilizing the relationship of producing gas-oil ratio and areal sweep efficiency as a function of pore volume injected (as obtained from data published by Dyes, Caudle and Erickson2), the theoretical performance was determined. This prediction is compared with actual performance to date. Actual performance reflects an increasing percentage of tniscible product in the produced fluid to a particular level, which remains static for a short period and then increases again to a higher level. This performance suggests that the reservoir has performed as a layered system. It is concluded that the layered-system approach can be used to predict performance in a highly stratified reservoir and that economic consideration is a limiting factor in determining the amount of the reservoir which can be miscibly swept. INTRODUCTION The Paloma zone in the Paloma oil field, Kern County, Calif., is comprised of several sand members separated by siltstone, shale and/or cherty sections. Rapid facies changes within the zone indicate that the sediments were deposited in a "near shore" environment. As a result, the Paloma sands have a high permeability variation, and the Paloma zone is comprised of several sand reservoirs. Since one of the sand reservoirs containing crude oil was not receiving the benefits of gas injection, consideration was given to recompleting certain wells to isolate the sand in order to perform a miscible-phase injection project and, thereby, to increase its ultimate oil recovery. Before proceeding with the project, a review of the literature was made to determine the miscible-slug size that would be required to maintain miscibility throughout the displacement process. Although the review showed that considerable information was available for homogeneous systems, insufficient information was available to determine slug-size requirements and to predict performances for a highly stratified reservoir. This paper has been prepared to describe the method used to determine the miscible-slug-size requirement and to predict the performance of the miscible-phase injection project initiated in the Paloma oil field. Although the Paloma project has only been in operation since Aug., 1958, sufficient production history has been obtained so that a comparison can be made with the predicted performance. DESCRIPTION OF RESERVOIR The reservoir in which the miscible-phase project was initiated in the Paloma field is shown on Figs. 1 and 2. Reservoir properties are as follows: average sand thickness, 43 ft; porosity, 19.1 per cent; water saturation, 47.2 per cent: oil viscosity, 0.328 cp; reservoir temperature, 250°F; reservoir pressure, 3,500 psi: gas saturation, 21.2 per cent at time of miscible product injection; and total net hydrocarbon pore volume, 19,993,000 reservoir bbl. LIMITATIONS The method described herein utilizes a layer-system approach, where injection into and production from each layer is assumed to be proportional to the layer's fractional capacity. The effects of increased fluid mobility on injection and production rates, in layers which have had breakthrough, are not reflected in this method. There has been considerable controversy over the slug size necessary to maintain miscibility throughout the displacement process. In this method, the slug-size

AT the Tulsa meeting of the A. P. I., the following reso-lutions, expressive of the policy of that organization, were among those adopted: RESOLVED, That we endorse the conclusion of the Federal Oil Conservation Board in its report of September, 1926, that the prevention of the waste of gas incident to the pro-duction of oil is of paramount importance in the conserva-tion and economical production of oil, and the president of the Institute is requested to appoint a committee of seven to devise and suggest to this board, or the executive com-mittee, such measures as will enable the industry, while continuing to meet the consumption requirements for pe-troleum and its products, to conserve in its natural state such reserves of petroleum as may not then be required for consumption. RESOLVED, That the president of the Institute appoint a committee of seven to formulate and recommend to this board or its executive committee, at the earliest practicable date, a program of legislation; Federal and State, to be advocated by the Institute giving sanction and effect to agreements by oil producers for the curtailment of produc-tion in pools where and during periods when there is over-production, having for their purpose the economical and orderly production of oil.

Jan 1, 1927

By Vassiliki G. Stavropoulou

Although plane-strain is the preferred method of analysing many rock mecahnics problems, little is known about the behaviour of rock under this loading condition. A simple and inexpensive apparatus has been built for laboratory testing of rocks in plane-strain conditions. A thorough .investigation of the specimen geometry and the friction end effects showed that the results can be considered as reliable. The behaviour of a brittle sandstone in the simplest plane-strain condition [(03 = 0)] is significantly different than that of the uniaxial compression [(02 = U3 = 0)]. The plane-strain values of the Young's Modulus and the Poisson's Ratio are decreased in comparison to the corresponding uniaxial values. Dilatancy is also reduced in plane-strain, whereas the pre-failure brittleness of the rock increases. The most dramatic effect of the plane-strain condition is that on the strength of the sandstone, which increases by 49 per cent in comparison to its uniaxial compression value.

Jan 1, 1982

The following is an incomplete list of members and guests who called at Institute headquarters during the period Feb. 10, 1918 to Mar. 10, 1918: W. G. Anderson, St. John, N. B., Canada. Charles E. Locke, Boston, Mass. L. M. Banks, Camp Meade, Md. E. T. Lednum, Joplin, Mo. P. E. Barbour, Albany, N. Y. C.' K. McDonald, Washington, D. C. Alan M. Bateman, New Haven, Conn. C. T. Malcolmson, Chicago, Ill. Graham Bright, Pittsburgh, Pa. Stuart B. Marshall, Badin, N. C. J. F. Callbreath, Washington, D. C. T. C. Merriman, New Haven, Conn. J. E. S. Clark, Riverside. Cal. Arvid E. Nissen, Gary, Ind. G. H. Clevenger, Palo Alto, Cal. Herbert G. Officer, Conway, S. C. George C. Crossley, Trenton, N. J. J. E. Parker, Bulawayo, Rhodesia, S. Afr. R. H. Eagles, Palmerton, Pa. Francis R. Pyne, Elizabeth, N, J. Charles Enzian, Pottsville, Pa. Alfred Hull Ramage, Joplin, Mo. Albert H. Fay, Washington, D. C. H. H. Stoek, Urbana, Ill. David B. Gemmill, Crown King, Ariz. G. M. Taylor, Colorado Springs; Colo. Ronald Harris, London, Ont., Canada. Charles Tubby, St. Paul, Minn. Wm. J. Hayes, Colombia. So. America. J. B. Tyrrell, Toronto, Canada. B. B. Hood, Chrome, N. J. Edmund W. Westervelt, Ymir, B. C. 0. P. Hood, Pittsburgh, Pa. Carl Zapffe, Brainerd, Minn. H. M. LaFollette, LaFollette, Tenn. W. S. Boyd, formerly superintendent of mines of the Ray Consolidated Copper Co., has been appointed assistant general manager. William Campbell, Professor of Metallurgy, at Columbia University, is acting as metallurgist at the New York Navy Yard.

Jan 4, 1918

By J. P. Morris

PREVIOUS investigations1,2 have shown that alloying elements in liquid iron influence the thermodynamic activity of sulphur and thereby affect the partition of sulphur between metal and slag in the desulphurization process. For example, the greater efficiency of desulphurization in the blast furnace as compared to the open hearth can be attributed in part to a higher level of sulphur activity in blast-furnace metal due to the higher concentration of carbon and silicon. In the present investigation, a short study was made of the influence of manganese on the activity of sulphur in liquid iron and iron-carbon alloys. In contrast to carbon and silicon, manganese was found to decrease the activity coefficient of sulphur; and in iron-carbon alloys it counteracts to some extent the influence of carbon. However, at manganese concentrations normally present in the blast furnace or open hearth, the effect of manganese is small. Since manganese sulphide has a limited solubility in iron, manganese can act, under certain conditions as a desulphurizing agent. Considerable data on the manganese-sulphur product in carbon-saturated melts were obtained in the investigation and have been included in this report. The experimental procedure was the same as that used in the earlier investigations on the effect of silicon' and carbon' on sulphur activity. Briefly, the method was as follows: The molten alloy, contained in a graphite or sintered alumina crucible, was brought to equilibrium at a constant temperature with a mixture of hydrogen and hydrogen sulphide of constant composition by bubbling the gas through the metal. Samples of' the melt were taken for analysis at regular intervals by suction through a 2 to 3 mm bore silica tube dipped into the metal. The experiments were run in a graphite spiral resistance furnace with melts weighing 50 to 60 g. The gas bubbling tubes were made of sintered alumina and were 5/16 in. OD, 1/16 in. ID, and 24 in. long. Equilibrium was assumed to have been attained when the sulphur content of the liquid metal reached a constant value. During an experiment there was a rapid loss of manganese from the melt by volatilization. To offset this loss, small additions of manganese were made periodically. The rate of manganese addition needed to maintain a constant manganese concentration was determined in preliminary tests. In all of the experiments, deposits of manganese sulphide formed above the melts in a cooler region of the furnace. Apparently, these deposits resulted from a reaction between manganese vapor and hydrogen sulphide in the gas. To prove that manganese sulphide did not volatilize from the melts to a measurable extent, an experiment was run in which helium was bubbled through liquid iron containing both manganese and sulphur. Although manganese volatilized rapidly in this test, there was no appreciable loss of sulphur. Volatilization of manganese sulphide from a melt would have led to an apparent equilibrium condition in which the sulphur content of the metal was lower than the true equilibrium value. The experimental results are shown in the first seven columns of Table I. The data in the last two columns were obtained from the previous work on the effect of carbon' and show what the results would have been in the absence of manganese but with temperature, gas composition, and carbon content of the metal remaining the same. Comparison of the last four columns show that, in the presence of manganese, the sulphur content of the metal increased at equilibrium and the activity coefficient of sulphur decreased. However, the results show that, for manganese concentrations below 3 pct, the effect of manganese is small. The values for activity coefficient of sulphur given in Table I were calculated from the following relations: S (in liquid metal) + H2 (gas) = H2S (gas) [l] K ph2s/?s X %S X phg = 0.00251 [2] where K is the equilibrium constant for the reaction, PH2S and ph2 are the partial pressures of hydrogen sulphide and hydrogen, respectively, and ?s is the activity coefficient of sulphur. The standard state for sulphur was taken to be a 1 pct solution of sulphur in pure iron. The numerical value for K at 1600°C was determined in the earlier work. For the purpose of showing graphically the results of the tests run at 1600°C, the activity coefficients of sulphur were recalculated so as to correspond to a manganese concentration in the metal of 2 pct in each case. In the calculation it was assumed that the increase in sulphur content of the metal at equilibrium caused by the presence of manganese

Jan 1, 1953

By John D. Morgan, Sylvain J. Pirson

AN instantaneous and continuous analysis of a mineral suspension should be of great value in controlling various mineral preparation processes. Described herein is a method of analysis based on the use of high-frequency alternating current, which, under certain restrictive conditions, could be of use. THEORETICAL CONSIDERATIONS In a suspension of conductive minerals, the electrical effect primarily responsible for the variations in electric conductivity is the capacitance. In Fig Ia, let an alternating voltage E be applied across two electrodes F and F', between which are two rows (S and T) of mineral particles, all of approximately the same size, immersed in a fluid. Let the number of rows of particles between the electrodes be R and the number of particles in each row be N. If A is the area of a particle, D is the distance separating two particles, and K is a constant depending on the fluid, the capacity, Co, of the particle system will be given by: [KRA C0 ND] Referring now to Fig Ib, let R, the number of rows, be held constant, but let N, the number of particles in each row (S and T), be increased X-fold. The capacity, C1, of [ ]

Jan 1, 1947

By Roy G. Mead

BECAUSE of its magnitude, and the type of occurrence, the deposit of boron minerals in the Kramer district, Kern County, California, is unlike any other in the world. Discovery of this vast deposit has brought about many changes in the borax industry, so a discussion of the geology, and the occurrence, would not be complete without a brief history of the development of the borax industry. Until the discovery of boron minerals in the desert regions of California and Nevada some seventy years ago, borax was imported from Tibet and India, principally for medicinal purposes, at almost prohibitive prices. Following the discovery of commercial deposits of boron minerals in California and Nevada, and the subsequent development of new uses for borax and boric acid, the consumption has steadily increased until today borax is used in some form or other in every household.

Jan 1, 1933

By ROBERT E. CROCKETT

MAGNETITE mining and milling in New York, New Jersey and Pennsylvania continued to remain comparatively inactive during 1933, owing to the low rate of output of the steel industry and also to unrestricted importation of foreign ores. However, some improvement over conditions existing in 1932 was noticeable, particularly in New Jersey, where one plant, that of the Washington mine of the Alan Wood Mining Co., at Oxford, went on full production in August. At Lyon Mountain, N. Y., the Chateaugay Ore and Iron Co. resumed mining and milling operations in October, on a reduced scale, principally to provide employment during the winter months. The Chateaugay company produces a special low-phosphorus pig iron. During the year they obtained a contract to supply their product for use in the manufacture of the suspension cables of the New. Golden Gate Bridge.

Jan 1, 1934

By AIME AIME

LOCAL COMMITTEES. EXECUTIVE.-W. A. Lathrop, Chairman; R. V. Norris, Secretary; S. D. Warriner, Treasurer; Irving A.. Stearns, W. J. Richards, H. S. Drinker, C. D. Simpson. GENERAL RECEPTION.-Irving A. Stearns, Chairman. Archibald, James, Jr., Pottsville. Lawall, E. H., Wilkes-Barre. Ashley, H. H., Wilkes-Barre. Lentz, W. 0., Mauch Chunk. Ayres, WV. S., Hazleton. Lewis, Albert, Bear Creek. Beard, J. T., Scranton. Loomis, W. H., Jeddo. Bridgman, J. C., Wilkes-Barre. Markle, Alvan, Hazleton. Bunting, Douglas, Wilkes-Barre. Markle, John, Jeddo. Chase, F. M., Wilkes-Barre. Neale, J. B., Minersville. Coroner, Eli T., Scranton. Norris, R. V., Wilkes-Barre. Cote, E. B., Jr., Drifton. Oliver, Paul A., Oliver's Mills. Davies, W. H., Hazleton. Owens, W. D., Pittston. Davis, H. G., Dorranceton. Pardee, 1. P., Hazleton. Dodge, W. F., Wilkes-Barre. Quin, R. A., Wilkes-Barre.

Jul 1, 1911

By A. E. Gorum, I. Cornet

Fatigrle of ionic crystals has been studied primarily in magnesinm oxide. under cyclic stress dislocations move irrreversibly; they multiply; slip bands form and grow; cracks mucleate and propagnte, and failure occurs. The use of ionic crystals such as MgO is advantageorus in such investigations because they are optically transparent. Individual dislocation Intersections with {100} surfaces may be observed with a standard microscope, using etch-pit techniques. Slip, deformation, crack .formation, and fracture in MgO crystals under cyclic stress are compared with cotrresponditzg processes in metals. ThE effect of cyclic loading in metals has been studied for many years. The appearance of slip lines is readily observed and the ensuing fracture may also be seen. From these observations it is possible to predict the behavior of a material and make an educated guess as to what is happening internally, but the actual changes taking place within the structure are not readily apparent. If one could obtain a material in which the individual glide components could be observed, it would be invaluable in determining the actual slip distribution resulting from cyclic loading as well as the distribution of slip in the neighborhood of a growing crack. Such a material is magnesium oxide. Dislocation arrays may be observed by means of etch pits

Jan 1, 1961

MISSOURI SCHOOL OF MINES The Missouri Mining Association has enjoyed a very good year. Last October the society was reorganized and the following officers elected for the year: E. Ross HOUSHOLDER, President, ORE N. MANESS, Vice-president, WILLIAM REBER. Secretary, RUAL CHAVEZ, Treasurer. The head of our mining department, Prof. C. E. Forbes, is now serving as a Major in the United States. Army. We were fortunate in having. Prof. Chas. E. Locke, of Boston, with us for part of the winter to take charge of the senior mining work. During the autumn and winter months we had a number of informal smoker lectures in Norwood Hall. Among the speakers at these meetings were: H. A. Buehler, Missouri State Geologist; Chas. E. Locke, Boston, Mass.; V. H. Hughes, Tulsa, Okla.; Dorsey Lyon, Washington; D. C.; Prof. G. H. Cox, Professor of Geology, Rolla, Mo.; together with a number of returned alumni.

Jan 8, 1918

By Michael Bradbury

INTRODUCTION A major change in financing exports in recent years has been the decreased importance of subsidized export credits, following the commitment of the OECD countries to eliminate the subsidy element. Subsidized export credit rates are now often more expensive than market rates as the financing for exporters has decreased in volume and importance. The forfait market, in recognition of this decreasing importance, provides a rapidly expanding source of nonrecource finance for exporters. The following is a step by step guide to what it is, how it works, its benefits and problems. WHAT IS FORFAITING? Forfaiting is not new. It has been used in Europe for about 25 years to provide export finance for both capital goods and commodities without recourse to the exporter. Although long the preserve of exporters in Germany, and more lately Italy, forfaiting is now used increasingly by exporters in Great Britain, the United States, Canada and Scandinavia. It is a fairly simple operation with easy straight-forward documentation. The transaction involves the purchase by the forfaiting bank of a bill of exchange or a series of bills without recourse to the exporter. These bills will have been drawn by the exporter, accepted by the importer, and will usually bear the unconditional guarantee of the importer's bank. They are normally drawn payable at intervals during the credit period agreed between importer and exporter and are purchased at a discount by the forfaiter. The exporter thus obtains his cash payment and the importer receives his credit period. The forfaiter collects the amount of the bills as they mature directly from the importer. Credit periods vary, depending upon the type of goods and the country and commercial risk of the importer. The period is generally between one and five years with six monthly maturities. The usual forfait currencies are US dollars. Deutschmarks and Swiss francs and others, such as sterling, French francs, and the Scandinavian currencies are being used more frequently. CHOOSING FORFAITING Most types of financing require the continued involvement of the exporter in the financial side of the transaction during the credit period. Forfaiting has certain comparative advantages. In particular, it is possible to forfait 100 percent of the risk without recourse to the exporter, unlike government sponsored export finance schemes, where some retention of the risk by the exporter is required. In addition, exports from country sources do not present problems and forfaiting can also cover trade within the EEC. Other benefits for the exporter are: (a) The exporter's balance sheet is improved; debts are turned into cash thus improving the liquidity of the company and enhancing its cash flow. And there are no contingent liabilities for bills of exchange. (b) If the sales contract is in a foreign currency forfaiting removes the risk to the exporter of adverse movements in foreign exchange during the credit period. (c) Fluctuations in interest rates during the credit period can be ignored since in forfaiting the transaction is usually done on fixed interest rate terms on a discount basis. (d) The political and transfer risks are taken by the forfaiter. (e) The commercial risk is taken by the forfaiter. (f) The costs of administration and collection etc. during the credit period are removed.

Jan 1, 1985

By Terry E. Perkins, Len Marnewecke

Installation of a relatively simple, low-cost analog mill control system at Amax Lead Co. of Missouri's Buick concentrator has paid off handsomely. The system, which provides the capability of handling mill circuit upsets and ore changes while maintaining a desired particle size, is expected to generate annually a return on investment of several times its capital cost. In addition, the system stresses simplicity of field instrumentation and control strategy, leading to better operator acceptance and understanding, and its capital cost makes it very attractive for the specific installation when compared to more complex schemes using mass flow measurement and computers for calculating circulating load to infer particle size. This system has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value.

Jan 2, 1978

By S. F. Ravitz, S. R. Zimmerley

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine. THE existence of the cobalt-copper deposits in the Blackbird district, Lemhi County, Idaho, has been known for many years. However, these deposits have not yet been exploited successfully because of the low grade of the ore, absence of information on ore reserves, and lack of feasible methods for concentrating and recovering cobalt from the ore. In 1941, when it appeared that World War II might interfere seriously with imports of cobalt from overseas, the U. S. Bureau of Mines started an extensive mining and metallurgical investigation of the Blackbird deposits. Exploration by trenching and drilling1 indicated that ore reserves were adequate to warrant consideration of large-scale exploitation. A process for producing high-grade cobalt concentrates from the ore was developed at the Salt Lake City Station of the Bureau,2 and hydrometallurgical procedures for producing cobalt metal or oxide from the concentrates were developed at the Boulder City Station.3 The Howe Sound Co., through a subsidiary, the Calera Mining Co., carried out further exploratory work, which increased probable ore reserves to a tonnage commensurate with a large investment in mine, mill, transportation facilities, and refinery. Simultaneously, the metallurgical staff of the company, working in cooperation with the Bureau of Mines, further investigated the metallurgical problems. It was the opinion of both groups that pilot-plant testing was required to translate laboratory results into plant operation. In general, the Blackbird ore has a high content of pyrite and some pyrrhotite and contains 0.5 to 1 pet cobalt and 1 to 2 pet copper, which are present essentially as cobaltite and chalcopyrite. The copper can be recovered readily as a high-grade concentrate by selective notation. The cobalt then can be recovered as a bulk sulphide concentrate assaying 4 to 5 pct cobalt, but no satisfactory procedure for separating the cobalt from the pyrite and pyrrhotite directly by flotation had been found. The method developed by the Bureau for producing a high-grade cobalt concentrate is essentially an application of the old Horwood process of selective roasting.4 The bulk sulphide concentrate is roasted to form an oxide coating on the iron mineral particles, and the calcine is then treated by flotation. The oxide coating prevents the iron minerals from floating so that it is possible to obtain a high recovery of cobalt in concentrates assaying more than 20 pct cobalt. Laboratory tests by metallurgists of both the Bureau and the Howe Sound Co. had indicated the optimum roasting temperature to be 425° to 450°C. At lower temperatures the rate of oxidation of the iron minerals is too low, whereas at higher temperatures substantial quantities of cobalt are rendered water-soluble. Because of its high sulphur content (35 to 40 pct), the bulk concentrate tends to continue to burn after it has reached the optimum roasting temperature. Although excessive temperatures could be avoided in the small-scale laboratory furnaces, there was considerable doubt that the temperature could be controlled properly in industrial equipment. To provide material for the pilot-plant tests, the Calera Mining Co. installed a small, temporary flotation mill at the Blackbird property and treated

Jan 1, 1951

By S. R. Zimmerley, S. F. Ravitz

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine. THE existence of the cobalt-copper deposits in the Blackbird district, Lemhi County, Idaho, has been known for many years. However, these deposits have not yet been exploited successfully because of the low grade of the ore, absence of information on ore reserves, and lack of feasible methods for concentrating and recovering cobalt from the ore. In 1941, when it appeared that World War II might interfere seriously with imports of cobalt from overseas, the U. S. Bureau of Mines started an extensive mining and metallurgical investigation of the Blackbird deposits. Exploration by trenching and drilling1 indicated that ore reserves were adequate to warrant consideration of large-scale exploitation. A process for producing high-grade cobalt concentrates from the ore was developed at the Salt Lake City Station of the Bureau,2 and hydrometallurgical procedures for producing cobalt metal or oxide from the concentrates were developed at the Boulder City Station.3 The Howe Sound Co., through a subsidiary, the Calera Mining Co., carried out further exploratory work, which increased probable ore reserves to a tonnage commensurate with a large investment in mine, mill, transportation facilities, and refinery. Simultaneously, the metallurgical staff of the company, working in cooperation with the Bureau of Mines, further investigated the metallurgical problems. It was the opinion of both groups that pilot-plant testing was required to translate laboratory results into plant operation. In general, the Blackbird ore has a high content of pyrite and some pyrrhotite and contains 0.5 to 1 pet cobalt and 1 to 2 pet copper, which are present essentially as cobaltite and chalcopyrite. The copper can be recovered readily as a high-grade concentrate by selective notation. The cobalt then can be recovered as a bulk sulphide concentrate assaying 4 to 5 pct cobalt, but no satisfactory procedure for separating the cobalt from the pyrite and pyrrhotite directly by flotation had been found. The method developed by the Bureau for producing a high-grade cobalt concentrate is essentially an application of the old Horwood process of selective roasting.4 The bulk sulphide concentrate is roasted to form an oxide coating on the iron mineral particles, and the calcine is then treated by flotation. The oxide coating prevents the iron minerals from floating so that it is possible to obtain a high recovery of cobalt in concentrates assaying more than 20 pct cobalt. Laboratory tests by metallurgists of both the Bureau and the Howe Sound Co. had indicated the optimum roasting temperature to be 425° to 450°C. At lower temperatures the rate of oxidation of the iron minerals is too low, whereas at higher temperatures substantial quantities of cobalt are rendered water-soluble. Because of its high sulphur content (35 to 40 pct), the bulk concentrate tends to continue to burn after it has reached the optimum roasting temperature. Although excessive temperatures could be avoided in the small-scale laboratory furnaces, there was considerable doubt that the temperature could be controlled properly in industrial equipment. To provide material for the pilot-plant tests, the Calera Mining Co. installed a small, temporary flotation mill at the Blackbird property and treated

Jan 1, 1951