Search Documents

By B. H. Kear, B. J. Piearcey

The orientation and temperature dependence of the tensile and creep propevties oj Mav-M200 crystals halle been determined. Crystals oriented for single slip exhibit ,maximum ductility, minimum work hardening, and least creep resistance, whereas crystals in multiple slip orientations show nzinimu~n ductility, strongest work hardening, and greatest creep resistance. At 1400" and 1600°F there is a marked improzlenzent in creep strength for orientations approaching [001] and [111], indicating that interactions between dislocations gliding in intersecting octahedral slip systems play an important role in creep resistance. At 1800°F the creep strength is much less dependent on orientation, which is rationalized in terms of slip in cube planes as well as octahedral A frequent mode of failure in high-strength cast nickel-base superalloys is by intergranular fracture, particularly along those grain boundaries oriented transverse to the major stress axis. VerSnyder and ~uard' demonstrated that this problem could be overcome by eliminating transverse grain boundaries through unidirectional solidification. Piearcey and versnyder2 made use of this principle in the development of unidirectionally solidified gas turbine blades and vanes, where the growth direction of the columnar grain structure coincides with the axis of principal stress under operating conditions. The present investigation was undertaken to determine if further improvement in properties may be obtained by eliminating grain boundaries altogether, so as to take advantage of the well-known dependence of mechanical properties of single crystals upon the orientation. 1) EXPERIMENTAL PROCEDURE Single crystals of Mar-M200* were grown from the melt under vacuum by a modified Bridgman method. The melt was poured into a preheated alumina mold, and crystal growth was promoted from one end by appropriate gradient cooling. Tensile and creep specimens (2 in. diam by $ in. gage length) were prepared by a series of operations involving electrical discharge machining, precision grinding, and electropolishing. The orientations of the specimens were determined by the Laue X-ray back-reflection method. Tensile tests were carried out in aWiedemann machine with furnace attachment, using a strain rate planes. In all orientations imzpvouement in the strength charactevistics of the material can be induced by heat treatment. Creep ad stress rupture data for (001) oriented crystals are compared with similar data obtailted previously joy random polycvystalline material, and also columnar grained material having a prejevved (001) orientation. The single-crystal )material exhibits both longer rupture life and lower minimum creep rate at all temperatuves, and the rupture elongation is comparable with that in the columnar grained material. From these results it is concluded that single crystals should and useful application in gas-turbine blades and tanes. The optimum orientation for a blade is considered to be with its axis of principal stvess parallel to (001) ou (111). of 0.0001 sec-'. Load and extension were recorded directly on an X-Y recorder. The strain measuring device consisted of extension arms attached to the grips at one end and leading out of the furnace to an LVDT (linear variable differential transformer) at the other. Creep tests were performed using a standard constant load creep frame. 2) DISCUSSION OF RESULTS 2.1) Structure of Alloy. The structure and segregation in as-cast and heat-treated Mar-M200 has been described in detail else where.~ The main features are as follows: the as-cast material is heavily cored, due to pronounced dendritic segregation during solidification; the dendrites are rich in tungsten and cobalt whereas the interdendritic regions are rich in chromium, titanium, nickel, and carbon. The structure consists of -60 vol pct coherent precipitate of y', basically Ni3(A1,Ti), in a matrix of y (nickel-base solid solution), interspersed in the interdendritic regions with minor MC carbides and -y' eutectic. The y' particles, and y-y' eutectic, contain more titanium, aluminum, and nickel, and less tungsten, cobalt, and chromium than the y matrix. Heat treatment partially removes segregation, eliminates the eutectic, refines the y' dispersion in y, and gives additional partially coherent M23Cs carbide. An as-cast crystal, therefore, is composed primarily of two oriented phases (y + y'), whereas the normally heat-treated crystal consists of three oriented phases (y + y' + MZ3Cs). Typical electron transmission micrographs of the y + y' structure are shown in Fig. 1. Crystals grown in the (100) orientation develop a simple unidirectional dendritic structure, Fig. 2, since (100) happens to be the preferred direction of growth for dendrites in this material. Crystals grown in the {110) and (111) orientations, however, tend to promote equal growth, generally in separate colonies, in the two and three geometrically favored (100) growth directions, respectively. In other orientations of growth, a single (100) dendrite direction generally pre-

Jan 1, 1968

By Reynold Q. Shotts

INTRODUCTION THE small domestic underfeed stoker as now designed is unusually sensitive to the coking and plastic properties of coals, and when the attempt is made to burn the high rank coking and caking coals of the Appalachian fields, serious trouble may occur. Part of the trouble may be caused by the ash content and clinkering characteristics of the particular coal in use, but more often it is the result of an excessive accumulation of coke in the form of "trees" or masses in the fuel bed. Often the zone of burning becomes so restricted that the fire goes out, and in extreme cases the fire may be lifted completely out of the fuel bed and away from the air ports. Even if the fire is preserved, excessive coking may cause response to subsequent heat demand to be slow and irregular. Coke trees seem to grow. most readily during periods of hold-fire operation, so that in order to preserve the fire in mild weather it is often necessary to set the timer for such a long operating period each hour that much unneeded and unwanted heat is developed, causing discomfort. During demand periods the fire may pick up so slowly that the intense burning which develops just before stoker cut-off causes a serious overshooting of the thermostat. Stoker coal performance tests which have been made in a number of laboratories 1, 2, 3, 4, 5 are one method of approach to the problem of selecting stoker coals. As yet these tests have not been standardized and they are expensive and time-consuming. The value of the results probably increases with the length of the test. Sherman and co-workers at Battelle Memorial Institute believe that even a one-week test is not too reliable a trial2 and it is quite likely that others will agree. A great advantage of such tests is that characteristics of coals, other than the tendency to form coke masses, may be evaluated from them. The selection of stoker coals would be greatly facilitated if there existed some simple measure of the tendency of a coal to form coke in a fuel bed. Although possessing all of the disadvantages of any small-scale laboratory test, the test for the free-swelling index of coal has been found useful for evaluating the probable effects of swelling properties upon combustion. 7 Ostborg, Limbacher and Sherman, have shown that the test can predict, roughly, the tendency of coke to accumulate in the fuel bed of a domestic stoker. They also gave instances of its value in predicting combustion behavior in some large installations. The use of the test for free-swelling index has become well established and has been adopted as a standard by the American Society for Testing Materials.8 When domestic stoker coal investigations began at the State Mine Experiment Station in the summer of 1944, it was decided

Jan 1, 1948

By Carter S. Cole

Mr. Chairman, Fellow Members and Guests, our chairman this morning got over into the geneological field, so perhaps I may be pardoned if I revert to some of my ancestral training and give you a text. I always like to talk about some special little text that may illustrate what we want to say. So the text that I will take for this afternoon is a very simple one, "Win the War." That is the guide for all of our actions, or should be. We should question everything we do to see what it does to contribute to winning the war. If we fail to do that, nothing else is going to count. On the wall of the office of one of the branch chiefs in the Copper Division in Washington there is a little slogan which I think we should take very deeply to heart, "The difficult we do right away. The impossible takes a little longer." I think that is a very good guide for us to follow in the work that lies ahead of us in the metallurgical field and in the handling of these secondary metals and the things that result therefrom. My subject is "Conservation and Specifications." Some people would wonder just where that fits in, and how you might define "conservation." One very good definition would be "the utmost use of our resources." If you will pardon my going back to some of my earlier experience for a little simile, those of you who know me know that for ten years after the last war I was in the railroad business. If we are with the engineman in a cab, and we have a green signal ahead of us, that is a clear signal and tells us to proceed at full authorized speed. Now suppose we come to a yellow signal that is caution, slow down to one-half authorized speed and be prepared to stop. Now if you do slow down, the chances are that that obstruction that was ahead of you will move out of the road, and you may get another yellow or caution signal at the next block, and be able to keep going at a slow speed. As of the date of Pearl Harbor our tin supply took on a very yellow tinge, and it threw the caution sign right in our faces. If we had not heeded that sign, and cut down our consumption of tin, we would not have any today; but because we have done so we are in a much better position today than we were a year ago, that is comparing our visible supply with our present rate of consumption as contrasted with the visible supply a year ago and our then rate of consumption.

Jan 1, 1943

By AIME AIME

THE STANDARD herewith submitted is the result of several years of research and consideration by the A.I.M.E. Technical Committee on Milling Methods. In the early work of this committee it was found necessary to undertake the development of a standard laboratory method for screen testing of ores. During the research stages the desirability of having this standard, when completed, approved as American Standard was brought out. In accordance with this idea, its initiation as a project of the American Standards Association (then the American Engineering Standards Committee) was approved by the latter body and the A.I.M.E. designated as sponsor. In 1929, the A.S.A., on recommendations of its advisory committee, the Mining Standardization Correlating Committee), authorized the A.I.M.E. to be sole sponsor for this project. The personnel of the Institute's Committee on Milling Methods was then increased to make it thoroughly representative of all diversified interests in the mining field. Two years ago the standard was circulated and has been given wide distribution. Early in 1932 the committee voted unanimously, with 38 affirmative votes, that the standard be recommended to the Board of Directors of the Institute for submission to the American Standards Association for approval as American Recommended Practice. This was accordingly done, at the Feb. 1.6, 1932, meeting of the directors, and the American Standards Association approved the standard on July 6; 1.932, designating it as ASA M5-1932.

Jan 1, 1932

By Ernest A. Hersam

The rate of output of a rock crusher is based upon a certain space relation, the calculation requiring that the size and position of the jaws, the principle of motion, and the speed of the machine be known. The result is a calculated maximum output. The purpose of this paper is to develop a method of calculating this maximum output, to judge the general applicability or utility of such a calculation, and, so far as possible, to lecord calculated values as a basis for the comparison of actual results, or for estimating the capacity of a new crusher or of a standard crusher working under new conditions. A method for calculating the capacity of crushing rolls, which has been in common use for a long time, is well presented by R. H. Richards.' The output is conceived as a ribbon of rock, of which the breadth, thickness and length are governed respectively by the width of the rolls, the space between them, and their peripheral velocity. The weight of the rock thus crushed in a given time can be calculated from its specific gravity, after applying a factor representing the percentage of voids in the hypothetical ribbon. The calculation of crusher capacity is made in a somewhat similar manner. While the action of rolls is simple, with few irregularities in operating conditions, in rock crushers the material advances intermittently, usually under the force of gravity alone, and is subjected to a variety of variable conditions. The effect of these variable influences upon the calculation of capacity is now to be shown. In this paper, capacity will be discussed quite apart from any consideration of mechanical efficiency; that is, results will be stated not in terms of output per horsepower, but of output for a given machine when operated at a known speed, constructed and adjusted to receive material of a known size, and to yield a product having a definite maximum coarseness.

Jan 1, 1923

By Ernest A. Hersam

The rate of output of a rock crusher is based upon a certain space relation, the calculation requiring that the size and position of the jaws, the principle of motion, and the speed of the machine be known. The result is a calculated maximum output. The purpose of this paper is to develop a method of calculating this maximum output, to judge the general applicability or utility of such a calculation, and, so far as possible, to lecord calculated values as a basis for the comparison of actual results, or for estimating the capacity of a new crusher or of a standard crusher working under new conditions. A method for calculating the capacity of crushing rolls, which has been in common use for a long time, is well presented by R. H. Richards.' The output is conceived as a ribbon of rock, of which the breadth, thickness and length are governed respectively by the width of the rolls, the space between them, and their peripheral velocity. The weight of the rock thus crushed in a given time can be calculated from its specific gravity, after applying a factor representing the percentage of voids in the hypothetical ribbon. The calculation of crusher capacity is made in a somewhat similar manner. While the action of rolls is simple, with few irregularities in operating conditions, in rock crushers the material advances intermittently, usually under the force of gravity alone, and is subjected to a variety of variable conditions. The effect of these variable influences upon the calculation of capacity is now to be shown. In this paper, capacity will be discussed quite apart from any consideration of mechanical efficiency; that is, results will be stated not in terms of output per horsepower, but of output for a given machine when operated at a known speed, constructed and adjusted to receive material of a known size, and to yield a product having a definite maximum coarseness.

Jan 1, 1923

By C. D. Woodward

THE subject of electric signals for the despatching off mining cages through shafts has received cousiderable attention recently from various mining companies. The Anaconda Copper Mining Co. has found it necessary to develop a system that is reliable, safe and simple in operation, and easy to repair. The movement of all mine cages or skips is under the direction of a station tender, who rides on the cages when men or supplies are being lowered or raised. When ore is hoisted, he is stationed at a skip pocket for loading and despatching the skips. For the station tender's use, two signal systems are installed in each hoisting compartment, and he is the only employee authorized to use them. One system is known as the "AC" or Station bells, as it is operated from the 110-volt, 60-cycle, power service; the other system, called the "DC" or shafts bells, takes its energy from closed-circuit primary batteries. As a supplement to the two main signals, a buzzer system is installed. The general arrangement is similar to "the main signal, except that there is a mine buzzer at each station. When a signal switch connected into the buzzer system is pulled down, all buzzers are operated, thus notifying the station tender that he is wanted at some particular level. Placed on the station posts, and within easy reach of the men on the cages, are the signal pull switches for the main signals. The station, or "AC," pull switches are furnished with a short rope as shown in Fig. 1, while the shaft, or "DC," pull switches are equipped with ropes that extend down the shaft past the next station. To avoid all confusion in the use of the three signal systems, a standard arrangement has been adopted in all mines for the location of the pull switches. Fig. 2 illustrates the position of the pull switch at the various mine stations for the main signal systems, but it does not show the buzzer pull switch; this is fixed to the roof timbers about 25 ft. back from the shaft. If the skip pockets are a considerable distance below the station, a pull switch for each main shaft compartment is connected to the "AC" system and placed at this point. However, if the distance is short, a light cord is attached to the station pull switches and dropped down to the skip pocket.

Jan 2, 1922

By Constantine Michalopoulos, Roger C. Van Tassel

Commercial demand for gold in the United States is important. It has a large impact on the total world commercial and overall non-monetary demand. Given the present free market price and our need to import gold, it has a substantial adverse effect upon our international payments position. But, according to most recent estimates, the United States demand is perhaps no more than 20% of the world as a whole. In 1971, United States consumption was estimated at 215.6 tons out of a total of 1,412.1 tons 1. This figure is very close to the 16% figure developed by Consolidated Gold Fields as the average for the years 1968-1970.2 Surveys of both production and use of gold on a world-wide basis are not new. With the bulk of gold production in only a few countries, it has been possible to develop fairly reliable series on gold output. Estimates have been developed on the known reserves of gold and probable output at various prices.3 On the demand side, figures have been somewhat less complete and reliable. The Bank for International Settlements and the Director of the United States Mint have regularly published estimates of commercial use in major industrial countries. The IMF has issued an increasingly comprehensive survey in its Annual Reports. The IMF has attempted to cover all nations-not restricting its efforts to major industrial nations-and has tried to estimate both gold taken for commercial uses (Estimated Industrial and Artistic Use) and for private hoarding. Their method is to begin with data on free world output plus any net sales by the Soviet Union, subtract any additions to world monetary stocks (or add to available supply for any net reductions in world monetary stocks), subtract estimates for commercial demand and have left as a residual an estimate for private hoarding. The method is straightforward and simple but the quality of the data is suspect. Industry sources tend to believe the figures as biased on the low side because of a persistent tendency to underreport gold movements.4

Jan 3, 1974

By E. S. Machlin

The wzodel of Blandin and Diplunt;, generalized to include a phase factor, is applied to the carbon-carbon interaction in iron. Darken&apos;s "energetic" model is generalized to include not only first neighbor interactions but further neighbor interactions as well. On the bases of these generalized models relations are derived for the activity of carbon in both austenite and ferrite in terms of the carbon-carbon Pair interaction energies. A single function then yields the pair interaction energies consistent with the experimental activities of carbon in both ferrite and austenite. Thus, a simple explanation is given for the observation that the nearest-neighbor interaction between carbon is repulsive in austenite and attractive in ferrite. Certain consequences of this approach are explored. OnE object of the present paper is to attempt to take into account the consequences of electrostatic contributions to the carbon-carbon pair interaction energy for carbon as a solute in iron. Friedel&apos; has shown that oscillations in electrostatic potential are to be expected about a solute atom in a metallic solution. Blandin and 6lant6&apos; have shown that such oscillations yield an interaction energy between pairs of solute atoms that obeys the relation: W{ = A cos(2ftFri + 4>)/(kFri)3 [l] where kF = Fermi wave vector, ri = distance between solute atoms comprising the pair7 <p = phase factor dependent only on electronic nature of solute and solvent, A = coefficient dependent only on electronic nature of solute and solvent. Machlin3 found that Eq. [I] accurately described the pair interaction energy derived from short-range order measurements based on field ion microscope observations of dilute alloys of platinum. He also found that the value of the phase factor $ derived from residual resistivity measurements agreed well with that obtained from the analysis of the short-range order data. Harrison and paskin4 were able to predict the long-range ordering energy of 0 brass using Relation [I] and residual resistivity values to predict the value of the phase factor $. Machlin5 has repeated their analysis and applied it to the prediction of the long-range ordering energy in AgZn and AgCd with excellent agreement between prediction and experiment. Both A and $ are independent of the crystal structure. The Fermi wave vector depends uniquely upon the conduction electron concentration per unit volume in the spherical approximation of the Fermi surface. Thus, Eq. [I] is expected to apply to both fer- rite and austenite with only one set of values of A and $. Mossbauer studies6 yield the result that iron has one 4s electron. We shall make an assumption found to hold previously for platinum3&apos;7 and nikel, which is that only the s electrons are involved in shielding the perturbing potential of carbon. With this assumption, kF = 1.35 A-l. Although A and $ may be obtained from certain mdels&apos;&apos;&apos; we shall take A and $ to be empirical constants in the spirit of Kohn and osko.&apos; Thus, Eq. [I] involves two adjustible parameters. Consequently, two independent relations in A and $I are required in order to evaluate them for carbon as a solute in iron. We may use a recent analysis of Aaronson, Domain, and poundg who showed that Darken&apos;s energetic model,1° as well as others, can be used to describe the activity-temperature data for carbon in iron in both the aus-tenitic and ferritic phases. Darken&apos;s model takes into account only first neighbor pair interactions. For our needs, all neighbor pairs need to be taken into account. It is convenient to generalize Darken&apos;s model. The result for the partition function for austenite is: over the temperature range 800" to 1200°C and where the uncertainty corresponds to one standard deviation. Eq. [4] effectively yields only one relation. Another relation is required to obtain unique values for A and $. One property of Eq. [4] is that it is independent of crystal structure. Hence, data for a iron can be used to obtain another relation. To arrive at this relation we must generalize Eqs. [2] and [3] so that they may be applied to the bcc a iron. The result is that:

Jan 1, 1969

By W. D. Robertson

The effect of a tensile stress in accelerating the corrosion-cracking of certain alloys of aluminum, magnesium and iron is widely recognized. The literature is extensive and it is only necessary to cite the recent ASTM—AIME Symposium,l There are, however, no experimental data conclusively showing the effect of an applied compres-sive stress. It has been inferred, from the generally accepted mechanism postulated for the acceleration of corrosion by an applied tensile stress, that a compressive stress would inhibit corrosion. Furthermore, it is observed that corrosion cracks invariably start on the tension side of a specimen bent as a simple beam. This observation has led to the suggestion that shot-peening of the surface would inhibit or eliminate stress-corrosion cracking in magnesium alloys and aluminum alloys. However, the degree of inhibition produced by shot-peening does not appear in the literature except for the above qualitative references which are unsupported by experimental data. Moreover, while peening undoubtedly imposes a surface compressive stress, the alteration of the surface by the severe cold-working involved complicates the interpretation of the results with respect to the effect of a compressive stress alone. If corrosion proceeds along preferential paths produced by precipitation from solid solution, it is easily understood how a component of tensile stress normal to these paths will accelerate the corrosion and lead to ultimate failure. On the other hand, if the metallurgical conditions are such as to create preferential corrosion paths, then it is difficult to understand how a compressive Stress, produced by shot-~eening Or any other method, can inhibit corrosion except in the sense that the accelerating factor is removed. Thus, if the basic corrosion mechanism remains unaltered, there should be little or no inhibition resulting from the application of a compressive stress if inhibition is defined as the reduction of the degree of corrosion below that experienced in the unstressed state. The experiment described below was performed to isolate and evaluate the effect of a compressive stress on the corrosion and stress-corrosion cracking of a high strength aluminum alloy (24-S); and, by a Comparison of the corrosion rate of &apos;pecimens subjected to an applied tensile stress, compressive stress and in the unstressed state, to clarify the role of stress in intergranular corrosion. Experimental Procedure The experiment was conducted with the aluminum-copper-magnesium alloy known as Duralumin 24-S.* Specimens, 0.064-in. thick, in the form of I-in. wide strips sheared parallel to the rolling direction,

Jan 1, 1949

By J. A. Herbst, A. L. Mular

Digital simulation is defined and simulation techniques are re- viewed. Typical methodology involves the selection of models, the adjustment of raw data, the selection of a fitting strategy, the assessment of model accuracy in a statistical sense, and the development of an executive simulation structure. Simulations serve as aids for process engineers in evaluating the feasibility of a proposed flowsheet and the effect of a modification to an existing flowsheet. In addition, simulation plays an important role in off-line optimization and in the evaluation of alternative circuit control strategies. Several examples are presented to illustrate these uses for simulation including applications in crushing circuits, grinding circuits, and flotation circuits. It is the opinion of the authors that, within the next decade, mineral processing plants will be studied routinely via digital simulation during the preliminary design stage. Simulation will constitute an important component of the design decision making process.

Jan 1, 1978

By B. M. Larsen, K. Heindlhofer

THIS paper describes a relatively simple electrical apparatus that, through the close analogy between the flow of heat and of electricity, enables one to solve quickly and with satisfactory accuracy many complex problems in heat flow. This device, developed in 1935, has proved especially useful in the solution of certain practical problems relating to the design and efficiency of regenerators for an open-hearth furnace or coke oven, yielding within a few hours information that would take weeks or even months to acquire by mathematical1.2 or experimental3 methods of comparable accuracy. Its description now is prompted by growing interest in such analogues, as shown by several recent papers.4.5 The analogy between flow of heat and of electricity appears to have been recognized first by Maxwell who, in his famous Treatise on Electricity and Magnetism (1881) says: The analogy between the theory of the conduction of electricity and that of the conduction of heat is at first sight almost complete. If we can take two systems geometrically similar, and such that the conductivity. for heat at any part of the first is proportional to the conductivity for electricity at-the corresponding part of the second, and if we also make the temperature of any part of the first proportional to the electric potential at the corresponding point of the second, then the flow of heat across any area of the first will be proportional to the flow of electricity across the corresponding area of the second. .. Thus, in the illustration we have given, in which flow of electricity corresponds to flow of heat, the electric potential to temperature, electricity tends to flow from places of high to places of low potential, exactly as heat tends to flow from places of high to places of low. temperature He noted, however, that this analogy is restricted: ... there is, however, one remarkable difference between the phenomena of electricity and those of heat. Suspend a conducting body within a closed conducting vessel by a silk thread, and charge the vessel with electricity. The potential of the vessel and of all within it will be instantly raised, but however long and however powerfully the vessel be electrified, and whether the body within be allowed to come in contact with the vessel, or not, no signs of electrification will appear within the vessel, nor will the body within show any electrical effect when taken out. But if the vessel is raised to a high temperature, the body within will rise to the same temperature, but only after a considerable time, and if it is then taken out it will be found hot, and will remain so till it has continued to emit heat for some time. The difference between the phenomena consists in the fact that bodies are capable of absorbing and emitting heat, whereas they have no corresponding property with respect to electricity. According to this statement the application of the analogy would be limited to problems of steady flow that do not involve heat-capacity effects. In spite of this

Jan 1, 1945

By J. S. Bryner

In the study of metallographic specimens in the electron microscope, there is need for a method of locating the same field in both the light microscope and the electron microscope. This need arises chiefly from the fact that in the electron microscope the magnification and degree of resolution are so much higher, and the field so much smaller than in the light rnicroscope that it is often difficult, if not impossible, to identify positively what is being observed. The difficulty is increased by the fact that, because a transparent film replica of the metal surface must be used in the electron microscope, micro-constituents can be identified not by their color but only by their texture and contours. For these reasons it is desirable to obtain a series of photographs showing the same field in both microscopes in order that the appearance of common microstructures and micro-constituents in the electron microscope may be identified and catalogued for future reference. The need for a method of locating the same field in both microscopes arises also when it becomes desirable to enlarge in the electron microscope for more detailed study a particular interesting structure observed in the light microscope. Using the standard polystyrene-silicalJ replica technique, in which the silica film replica is fished from the ethyl bromide on a 1/8 in. diam zoo-mesh specimen screen, the possibilities of locating a particular area on the film in the electron microscope are rather remote. The desired structure may be obscured by the wires of the specimen screen or unrecognizable at the high magnification. A solution to the problem would be provided if a specially designed specimen screen, containing an opening which could be absolutely identified and quickly located in the electron microscope, could be fastened to the silica film replica in such a position that the desired field on the specimen would be located at the identifiable opening in the specimen screen. The design for such a specimen screen, a method for producing it, and a technique for fastening it to the silica film replica are described below. Description OF Method The Specimen Screen A simple design for a specimen screen containing an opening easy to identify and locate in the electron microscope is one with two lines of openings at right angles in the form of a cross. Such a screen is shown in Fig I. The opening at the center of the cross is identified easily and can be located quickly in the light microscope and in the objective image of the electron microscope. The specially designed specimen screens for this work were produced in quantity by electroforming. On both sides of a polished strip of copper I X 3 X 1/8 in., twenty patterns of the cross of openings were punched with a diamond point micro-hardness tester, using a load of magnitude

Jan 1, 1949

By A. C. Heath, E. H. Dix

The importance of aluminum-silicon alloys in thc light alloy field is now generally recognized. Where silicon was once considered detrimental to the properties of aluminum, useful alloys now contain as much as 13 per cent. Furthermore, silicon is present as an impurity in aluminum of even the purest grades. Iron is another important impurity in aluminum and likc silicon is found in small quantities in the purest aluminum available today. The manner of occurrence of iron and silicon in commercially pure aluminum and many of its alloys exerts a very pronounced influence upon their properties. The effect of large quantities of iron in aluminum-silicon alloys is so detrimental that it has been found necessary to limit the allowable maximum percentage to as low a figure as is consistent with quantity production and satisfactory physical properties. The intimate relation existing between iron and silicon in aluminurn and alurninum alloys makes necessary a more complete knowledge of this ternary system. This paper is divided into two principal parts, dealing respectively with aluminum-silicon solubility equilibria and the constitution of aluminum-iron-silicon alloys. Part I.—Aluminum-silicon Alloys The early work on this system was largely confined to determining the general form of thc diagram and in this respect the results are in good agreement. Briefly, alulninunl and silicon form a simple eutectifcrous series without compounds. Until recently the solid solubility of silicon in aluminum had not been accurately determined. Ipraenkell (1908) stated that aluminum will retain 0.5 per cent. silicon in solid solu-t&apos;ion. Rosenhain, Archbutt and Hanson2 gave the maximum solubility as about 1.50 per cent. and added that "this solubility docs not appear

By D. L. McElroy

It is too broad a statement to say that the mine car is the most important unit in a haulage system, but almost every mining man will admit that it is one of the most important. The mine car is to the mine haulage system what the railroad car is to the railroads; the main purpose in each instance is to move the greatest number of ton-miles of material at the least cost. The data presented in this paper are taken from a study of mine haulage conducted by the School of Mines of West Virginia University at 42 mines in 8 coal fields of Wrest Virginia. The study was made possible by a graduate fellowship of the School of Mines and the cooperation of the mining companies of the state. Three important factors in the use of mine cars in West Virginia are: (I) the number of mine cars in use per loader; (2) the capacity of mine cars; (3) the distribution of mine cars. ("Loaders" in this paper refers to all men loading coal, whether manually or mechanically.) During the World War many mine managers were annoyed by the reduction of efficiency and production caused by railroad-car shortages. Today relatively little complaint is heard about a shortage of mine cars, yet possibly 50 to 75 per cent. of the mines in West Virginia are suffering from this cause of reduced production and increased costs. The railroads have solved their car shortage by placing in service more cars of larger capacity and better design. Many coal mines in West Virginia should solve a part of their cost problems by the same simple procedure. Such a procedure requires an initial outlay of capital, but there is little doubt that this will be repaid, with a good return on the investment. Determining Number of Cars Needed There can be no mathematical rule to determine the number of cars which should be in use per loader in a coal mine, because numerous factors such as concentration of mining, system of haulage, car capacity, speed of haulage, distance of working places from tipple, and so forth, affect materially the number of cars in use. These factors in turn are more or less determined by height of bed, character of roof and coal,

Jan 1, 1931

By E. A. Nesbitt

The important permanent-magnet alloys 15 years ago contained carbon and depended upon it for their permanent-magnet properties. In recent years great advances have been made in a number of new alloys substantially free of carbon. These include Remalloy,&apos; an alloy of iron, cobalt, and molybdenum, the various iron-nickel-aluminum alloys of the Mishima2 type, and the more recent Alnico V3 in which the best properties are developed by heat-treating in a magnetic field. The Mishima and the Alnico types of alloys are very brittle and after casting must be ground to size. This article describes a permanent-magnet material4 that can be machined as cast, and when handled with some care can be rolled to thin sheet and drawn to fine wire. Optimum magnetic properties are developed by a simple heat-treatment, and at this time the ductility of the alloy disappears. If the cast alloy is heat-treated without cold-working the mag netic energy product is about 1.0 X 106. This material is called Vicalloy I (pronounced vicalloy, V for vanadium, I for iron, and C for cobalt). When the alloy is first hot-worked and then considerably reduced in area by cold-swaging, drawing or grooved rolling, it is found that after heat-treatment the magnetic energy product measured in the direction of previous extension can be increased to 2.0 to 3.5 X 106. These higher values have been obtained only after reductions in area of 75 to 95 per cent, and since the material hardens considerably during working, the reduction ordinarily can be accomplished only in fine wires, although larger sizes can be reduced by the use of powerful machinery. When the material has been cold-worked in such a manner as to improve its energy product substantially, it is called Vicalloy 11. Commercial use of Vicalloy has been made in the recording of speech. Tape 0.002 by 0.050 in. has been found superior in quality to all others tried, and is now used in the Western Electric Mirrorphone 5 In a variety of forms Vicalloy I or I1 is useful in many laboratory instruments, and in experiments in which the sizes and shapes required cannot be obtained with the other more brittle permanent-magnet materials. In 1936, during a study of other age-hardening magnetic systems, it occurred to the author that some of the iron-cobalt-vanadium alloys might be suitable for permanent magnets. The proportions of iron, cobalt, and vanadium were varied and a range of alloys of particular interest was found, as shown by the indicated area in Fig. I. The limits of this range of composition are 30 to 52 per cent iron, 36 to 62 per cent cobalt, and 4 to 16 per cent vanadium. The compositions indicated by points outside this area were also tested. Preparation and Properties OF Vicalloy I The alloys were usually cast in graphite molds into bars 3/4 in. in diameter and

Jan 1, 1946

By E. A. Nesbitt

The important permanent-magnet alloys 15 years ago contained carbon and depended upon it for their permanent-magnet properties. In recent years great advances have been made in a number of new alloys substantially free of carbon. These include Remalloy,&apos; an alloy of iron, cobalt, and molybdenum, the various iron-nickel-aluminum alloys of the Mishima2 type, and the more recent Alnico V3 in which the best properties are developed by heat-treating in a magnetic field. The Mishima and the Alnico types of alloys are very brittle and after casting must be ground to size. This article describes a permanent-magnet material4 that can be machined as cast, and when handled with some care can be rolled to thin sheet and drawn to fine wire. Optimum magnetic properties are developed by a simple heat-treatment, and at this time the ductility of the alloy disappears. If the cast alloy is heat-treated without cold-working the mag netic energy product is about 1.0 X 106. This material is called Vicalloy I (pronounced vicalloy, V for vanadium, I for iron, and C for cobalt). When the alloy is first hot-worked and then considerably reduced in area by cold-swaging, drawing or grooved rolling, it is found that after heat-treatment the magnetic energy product measured in the direction of previous extension can be increased to 2.0 to 3.5 X 106. These higher values have been obtained only after reductions in area of 75 to 95 per cent, and since the material hardens considerably during working, the reduction ordinarily can be accomplished only in fine wires, although larger sizes can be reduced by the use of powerful machinery. When the material has been cold-worked in such a manner as to improve its energy product substantially, it is called Vicalloy 11. Commercial use of Vicalloy has been made in the recording of speech. Tape 0.002 by 0.050 in. has been found superior in quality to all others tried, and is now used in the Western Electric Mirrorphone 5 In a variety of forms Vicalloy I or I1 is useful in many laboratory instruments, and in experiments in which the sizes and shapes required cannot be obtained with the other more brittle permanent-magnet materials. In 1936, during a study of other age-hardening magnetic systems, it occurred to the author that some of the iron-cobalt-vanadium alloys might be suitable for permanent magnets. The proportions of iron, cobalt, and vanadium were varied and a range of alloys of particular interest was found, as shown by the indicated area in Fig. I. The limits of this range of composition are 30 to 52 per cent iron, 36 to 62 per cent cobalt, and 4 to 16 per cent vanadium. The compositions indicated by points outside this area were also tested. Preparation and Properties OF Vicalloy I The alloys were usually cast in graphite molds into bars 3/4 in. in diameter and

Jan 1, 1946

E. R. JETTE*—The way this ternary was developed there are two directly determined points on each of the iso-thermals except the 700° isothermal, where I believe there is only one. How were the end points determined, and what was the basis for it? Whose work formed the basis for the silver copper line ? M. B. BEVER †—At most temperatures the authors determined three points of the isothermal line. For example it can be seen from Fig 3 and 4 how three points for the 600°C contour line were obtained. The authors took two additional points for each temperature from the copper-silver binary diagram contained in Hansen&apos;s volume on constitution diagrams. It is correct that the 700°C contour line is based only on one point in the ternary field which was found by a slight extrapolation of Fig 4. R. I. JAFFEE*—Are the tie lines representing phases in equilibrium parallel to the silver-copper boundary ? M. B. BEVER—Are you asking that as a matter of principle ? R. I. JAFFEE—I assumed that would follow from principle. I wonder if that is in accordance with the authors&apos; ideas too. M. B. BEVER—I do not believe the authors obtained any information on the tie lines in the two-phase field. Of course, in the limiting case of very low gold contents the tie-lines approach to the silver-copper boundary, but generally in the two-phase field I do not think that the tie-lines have to be parallel to the boundary. E. R. JETTE—1 am quite sure they do not have to be parallel. You cannot tell from this work in which direction they go. E. A. GULBRANSEN*—Were any pycnometric measurements made to check the lattice parameters of the alloys ? M. B. BEVER—I did not hear any-

Jan 1, 1950

By R. F. Mehl, C. S. Barrett, A. H. Geisler

THE mechanism by which the super-saturated solid solution of 20 per cent silver in aluminum decomposes has been reported in two previous publications. 1,2 The analysis of streaks in Laue photograms showed that thin platelike particles (the so-called Guinier-Preston aggregates) form upon {111} matrix planes in the early state of decomposition.1 The size of these particles is larger, the higher the temperature at which they form in accordance with nucleation theory;3 at all temperatures they increase in size with aging.2 When they have grown thick enough to afford three-dimensional diffraction, powder X-ray photograms show that the structure is not that of the equilibrium precipitate y but that of a transition lattice ?&apos;. Since this is also platelike in shape and also lies upon the {111} matrix planes with the {110} direction in the matrix parallel to the {11.0} direction in ?&apos;, it seems likely that the original platelet particles are merely ?&apos; in an early stage of formation, and thus finely dispersed. The atomic spacing and pattern on the {00.0} plane in ?&apos; are identical with those on the {111} matrix plane to which it lies parallel, and since comparable directions in the two planes are parallel, the lattices are thus coherent at the interface; an analogous coherence has been found in aluminum-copper alloys.3 The structures ?&apos; and y are both close-packed hexagonal and are oriented alike; they differ only in interatomic distances. Consequently, ? &apos; is regarded as y strained from its ordinary dimensions by the lattice coherency between it and the matrix.2 The lattice movements that transform the matrix to the equilibrium precipitate appear to be very simple.2 The mechanism of precipitation in this system is simpler and is more precisely known than that in any other system,2,4 hence the system should be a profitable one for the difficult task of correlating property changes with structural alterations. The present report provides additional studies on powder X-ray diffraction from alloys of 10 per cent, 20 per cent and 30 per cent Ag, and presents the correlation of crystallographic changes with changes in microstructure, Brinell hardness and electrical resistivity of the three alloys. PREPARATION OF SAMPLES AND EXPERIMENTAL PROCEDURE The preparation of the 20.2 per cent Ag alloy has been described.2 Alloys containing 9.9 and 29.7 per cent Ag were prepared from 99.97 per cent Al and 99.99+ per cent Ag using a similar procedure. Rolled

Jan 1, 1943

By Harry K. Ihrig

THE hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1/8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was, necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes Co. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.11 The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 DESCRIPTION OF TEST METHOD The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1945