Search Documents

By Donald W. Scott

Generally speaking, there is nothing very difficult about taking good microgrztphs of photogenic thin sections or grains with a petrographic microscope-camera setup. However, sometimes it is desired to show some detail that cannot be illustrated satisfactorily by the usual micrographs taken with parallel polarized light, with crossed nicols, or even with two micrographs. A simple procedure giving good results has been used at Battelle Memorial Institute for subjects falling into this classification, and it is believed to be of interest, especially to research people who must sell a point to executives through the medium of well-illustrated reports. The following problem illustrates a typical application: It is desired to photograph a thin section of an iron ore to illustrate the character and association of the iron oxides and the individual quartz crystals. A magnification of 75 dia. is acceptable. A micrograph of the field in question (Fig. Ia) was taken with parallel polarized light. Due precaution was taken to provide critical illumination, correct exposure, a sharp focus, a good darkroom technique, and other essential conditions. It illustrates correctly the iron oxides, but it fails to show the individual quartz crystals. A micrograph of the identical field (Fig. Ib) was taken under the same precise conditions, but with crossed nicols. It gives a better idea of the character of the individual quartz crystals but is likely to be misinterpreted unless accompanied by a lengthy descriptive note. This micrograph suggests that the centrally located, large black area is composed entirely of iron oxides. That this' is an incorrect interpretation is evident by reexamining the micrograph of Fig. Ia. The correct interpretation is that the dark area contains quartz crystals oriented with their optical directions parallel to, or nearly parallel to, the vibration directions of the polarizer and analyzer of the microscope. Thus, the executive, or anyone who had not done the work personally, would get no more than a fair interpretation, even if two micrographs were included; and in the interests of both brevity and clarity, one micrograph usually is more desirable. Exactly how many quartz crystals occur in this region cannot be told from the two micrographs, and a printing of the two negatives in register would likewise not show the detail desired. Thus, it is evident that some subjects cannot be satisfactorily illustrated by the usual procedures. In photographing Fig. Ic the light was subdued and, during the entire exposure of 75 sec., the analyzer nicol was rotated uniformly in its mounting from a crossed position to 45° uncrossed position to introduce the desired amount of contrast in the various individual quartz crystals. The true reproduction of the character and association of the iron oxides, and the additional structure and detail in the quartz areas, is apparent. It might be

Jan 1, 1949

By Donald W. Scott

Generally speaking, there is nothing very difficult about taking good microgrztphs of photogenic thin sections or grains with a petrographic microscope-camera setup. However, sometimes it is desired to show some detail that cannot be illustrated satisfactorily by the usual micrographs taken with parallel polarized light, with crossed nicols, or even with two micrographs. A simple procedure giving good results has been used at Battelle Memorial Institute for subjects falling into this classification, and it is believed to be of interest, especially to research people who must sell a point to executives through the medium of well-illustrated reports. The following problem illustrates a typical application: It is desired to photograph a thin section of an iron ore to illustrate the character and association of the iron oxides and the individual quartz crystals. A magnification of 75 dia. is acceptable. A micrograph of the field in question (Fig. Ia) was taken with parallel polarized light. Due precaution was taken to provide critical illumination, correct exposure, a sharp focus, a good darkroom technique, and other essential conditions. It illustrates correctly the iron oxides, but it fails to show the individual quartz crystals. A micrograph of the identical field (Fig. Ib) was taken under the same precise conditions, but with crossed nicols. It gives a better idea of the character of the individual quartz crystals but is likely to be misinterpreted unless accompanied by a lengthy descriptive note. This micrograph suggests that the centrally located, large black area is composed entirely of iron oxides. That this' is an incorrect interpretation is evident by reexamining the micrograph of Fig. Ia. The correct interpretation is that the dark area contains quartz crystals oriented with their optical directions parallel to, or nearly parallel to, the vibration directions of the polarizer and analyzer of the microscope. Thus, the executive, or anyone who had not done the work personally, would get no more than a fair interpretation, even if two micrographs were included; and in the interests of both brevity and clarity, one micrograph usually is more desirable. Exactly how many quartz crystals occur in this region cannot be told from the two micrographs, and a printing of the two negatives in register would likewise not show the detail desired. Thus, it is evident that some subjects cannot be satisfactorily illustrated by the usual procedures. In photographing Fig. Ic the light was subdued and, during the entire exposure of 75 sec., the analyzer nicol was rotated uniformly in its mounting from a crossed position to 45° uncrossed position to introduce the desired amount of contrast in the various individual quartz crystals. The true reproduction of the character and association of the iron oxides, and the additional structure and detail in the quartz areas, is apparent. It might be

Jan 1, 1949

By D. A. Elgillani, M. C. Fuerstenau

In this paper, oxidation potentials measured in the presence of various concentrations of cyanide, ferro-cyanide, and ferricyanide and ethyl xanthate at various values of pH are related to flotation response. Eh-pH diagrams are presented to show that the formation of surface ferric ferrocyanide is probably responsible for depression when cyanide is added. The influence of cyanide on the depression of pyrite with xanthates as collector has been the subject of a number of investigations,'-6 and several theories on the mechanism of depression have evolved from these studies. Wark and Cox7 and Gaudin8 have suggested that the depressing effect is due to a competition of cyanide ion with xanthate ion for the surface. Cook and his colleagues9-11 have explained this phenomenon in terms of competition between hydrocyanic acid and xanthic acid. Sutherland 12 has shown that although both of these theories accurately describe the relation between pH value and cyanide addition at constant collector addition, they fail to describe the relation between pH value and the amount of collector required to cause flotation. Taggart 13 suggested that depression in these systems is due to the formation of a reaction product between ferric ion at the pyrite surface and ferrocyanide ion derived from solution. Majumdar4,6 has attempted to prove this hypothesis by measuring the contact angles of pyrite in the presence of 25 mg per liter ethyl xanthate and different concentrations of potassium ferrocyanide and ferricyanide. In all cases the contact angles were quite high up to pH 10. These results indicate that pyrite should not be depressed by either potassium ferrocyanide or ferricyanide. In view of these facts, Majumdar has assumed that the compound Fe(CN)2 forms at the surface. Gründer and Bornl4 have stated that depression may be due to the formation of the compound K2Fe(II)Fe(CN)6 at the pyrite-solution interface. This compound is thought to be an interaction product between the K2Fe(CN)6-2 ion from solution and the Fe++ ion at the pyrite surface and, accordingly, K4Fe(CN)6 should depress pyrite at least as effectively as KCN. This was proven experimentally, but there was no simple relation between the depression of pyrite and the concentration of either KCN or K4Fe(CN)6 in solution. In view of the many mechanisms that have been proposed for pyrite depression by cyanide, it is apparent that a clear understanding of the phenomena occurring in these systems is lacking. One reason for this may be the fact that the species responsible for pyrite flotation in the presence of xanthate is not the xan-thate ion but rather dixanthogen.15 Since the oxidation of xanthate to dixanthogen is dependent on the oxidation potential of the solution, it would seem that knowledge of these potentials would be a requisite to understanding the pyrite-xanthate-cyanide system. It is the object of this paper to measure both the oxidation potential and pH of the pyrite systems in the presence of various concentrations of cyanide, ferrocyanide, and ferricyanide and xanthate and to relate these values to flotation response. EXPERIMENTAL MATERIALS AND 'TECHNIQUES In the experiments discussed here, pure potassium ethyl xanthate was used as collector, and reagent grade potassium cyanide, potassium ferrocyanide, and potassium ferricyanide were used as depressants. Reagent grade HC1 and KOH were added for pH adjustment. Conductivity water, made by passing distilled water through an ion exchange column, was used in all experimental work. Two natural samples of pyrite were used in the investigation. Sample preparation for flotation included dry grinding with a mortar and pestle and sizing the product to 100 x 200 mesh. Prior to flotation, a 0.75-gm sample of pyrite was added to a solution containing a known amount of depressant at the desired pH value, and the system was conditioned for 4 min. Following this, a known amount of collector was added and the system was conditioned for another 4 min. The pH — termed flotation pH - was measured; the pulp was transferred to a Hallimond cell, and flo-

Jan 1, 1969

By J. S. Aronofsky, R. Jenkins

A simple means of predicting the flowing well pressure history in a natural gas reservoir has been developed. The differential equation for unsteady radial flow of gases through porous media was solved by numerical methods using electronic punch card machines. The results obtained from these calculations are presented in a generalized form which is believed to be most convenient for engineering use. These results are compared with those presented in a paper by Bruce, et al4. An effective radius of drainage has been defined which permits the equation of steady state gas flow to be used easily to predict well pressures in gas reservoir depletion. An equivalent effective radius of drainage is defined for liquid flow systems and a comparison is made of the gas solution to the liquid solutions. INTRODUCTION This paper presents a numerical method for describing the transient flow of gases radially through a porous medium from which the production rate is specified. The results obtained from these calculations are presented in a generalized form which is believed to be the most convenient for engineering use. The principal application of these calculations should be to flow in natural gas reservoirs, in the interpretation of pressure drawdown tests, in the estimation of reserves, and in calculation of injection pressures required in gas injection and cycling operations. The evaluation of natural gas wells is based upon back-pressure tests in which measurements of production rate and flowing well pressure are made for periods of one, two, or more days. The flow is assumed to have stabilized at this time, and the observed values of pressure and production rate are used with standardized formulae to determine the well's allowable production rate. Furthermore, the results obtained from such a test of short time duration are extrapolated in such a manner to allow a prediction of what the well pressure will be at some future time for a specified (but possibly untested) flow rate. The manner of conducting such back-pressure tests suggests several questions as follows: 1. 'What is the definition of stabilized flow and what factors determine the length of time required for the flow to become stabilized? 2. How may the recorded values of pressure and rate be utilized? 3. As the well is produced and the reservoir pressure falls, how will the flowing well pressure change? Can this flowing well pressure be predicted from the back-pressure test? 4. Are the results obtainable from the test influenced by a particular procedure used in obtaining the results? 5. Is it possible to estimate the gross reservoir permeability from back-pressure data? It is not within the scope of this paper to provide solutions Or even to discuss adequately all the above questions. However. in considering such matters, the

Jan 1, 1955

By R. B. Schluter, M. M. Fine

A process for winning copper from pelletized chalcocite concentrate without matte smelting and converting is under development at the Twin Cities Metallurgy Research Center of the U.S. Bureau of Mines. The new procedure includes a two-stage fluid-bed treatment in which the pelletized concentrate with 33% Cu and 7% S is first desulfurized to about 0.5% S in an oxidizing atmosphere, and then metallized by reduction with hydrogen. The reduced product is melted with flux to separate metallic copper from the gangue. The metal must be refined to remove residual sulfur and iron. The pelletizing of the fine concentrate into mini-pellets prior to fluid-bed treatment is an important feature of the process, because it permits shorter reaction time, decreases dusting, and facilitates subsequent processing.

Jan 1, 1972

By John L. Lamont, Walter Crafts

AN investigation has been made of the multiplying factors for some of the more common alloying and deoxidizing elements for use in calculating hardenability of steel according to Grossmann's method.1 The factors for manganese, silicon, and aluminum that were reported in an earlier communication2 have been confirmed by microscopic determination of the half-martensite structure rather than on the basis of an empirically determined hardness corresponding to a half-martensite structure. Measurement of ideal critical diameter by microscopic examination was found to he necessary for other alloying elements, and multiplying factors for nickel, chromium, molybdenum, zirconium, vanadium, titanium, and boron have been determined. The nature and order of magnitude of the multiplying factors reflect the effect of the alloying elements on the structural character of the steel. Except for nickel and vanadium, the multiplying factors agree fairly well with previously published results. Good correlation between actual and calculated ideal critical diameters has been found in developing the multiplying factors and in checking the results against fairly simple steels. However, some discrepancies have suggested the need for a more thorough study of low-carbon and complex steels. TESTING PROCEDURE The investigation was conducted principally on steels made at the Union Carbide and Carbon Research Laboratories, Inc., in high-frequency induction furnaces using Armco iron and standard alloying materials. However, a few open-hearth steels were used in establishing the effect of nickel, and the hardenability factor for boron was based primarily on open-hearth steels. All bars were normalized prior to the machining of Jominy hardenability specimens. The Jominy test was carried out under conditions standard for the test.3 Austenitizing temperatures judged to-be-appropriate for the composi¬tions of the steels were used., Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Residual amounts of phosphorus, sulphur, nickel, chromium, molybdenum, and copper were determined on only one heat of each group made with the same materials during the same period. "Acid-soluble" aluminum and zirconium rather than total amounts were determined, as it is considered probable that the acid-soluble amount is more representative of the effective alloy. As tin was present to the extent of only 0.002 per cent, its effect was neglected. The method used to determine boron in the steels shown in Table 9* was developed by Galen Porter, Vincent Napoleon, and Thomas R. Cunningham,of the Union Carbide and Carbon Research Laboratories, Inc., and is. a modification of J. Naftel's procedure for boron in soils

Jan 1, 1944

By M. Muskat, H. G. Botset, R. D. Wycoff, M. W. Meres

The subject of the flow of homogeneous fluids—gases alone or gas-free liquids—through porous media may be considered at the present time to be fairly well completed. That is, analytical, graphical, numerical, or experimental methods are now available for obtaining detailed descriptions of the behavior of such homogeneous fluid systems of any reasonable geometry. Thus, satisfactory empirical techniques are now well established for the determination of the permeability of porous media for homogeneous fluids, the numerical magnitude of this permeability uniquely and completely describing a porous medium as a carrier of a homogeneous fluid. Considering this constant as known, the treatment of a wide variety of specific problems involving either the flow of gases or liquids has been carried through to satisfactory conclusions. Beginning with the simple case of strictly radial two-dimensional flow of a liquid or gas into a well under steady-state conditions, generalizations have been developed to apply for systems where the flow is not strictly radial, due either to a lack of uniformity in the reservoir pressures at points distant from the well or deviations from circularity of the external boundary whereby the fluid is being supplied, and finally, to the lack of complete penetration of the well into the producing strata. Satisfactory descriptions are now available for cases where gravity is acting as the driving agent inducing the flow of liquid into the well, either alone or as a supplement to the effect of pressure. The effect of acid treatment on limestone wells has been given a reasonable interpretation on the basis of the fundamental theory of the flow of homogeneous fluids through sands, as have the important features of the problem of water-coning. Then, too, systems in which the outlet of the fluid from the underground reservoir is of a predominantly multiple character may be now considered as in the domain of

Jan 1, 1937

The production of petroleum in India (including Burma) increased from 334,811,624 gal.' ill 1936 to 350,322,222 gal. in 1937, the highest figure in the history of the industry. The increase in 1937 was clue to an increase of some 20 million gallons from Singu, 51/2 million gallons from Attack, 11/4 million gallons from Thayetmyo, and 1 mi1lien gallons from Digboi, accompanied by decrcases of 91/2 million gallons from Yenan-gyaung and 2 million gallons from Yenangyat,. The amount of gasoline produced from natural gas during the year was 10,616,313 gal. in Burma and 456,780 gal. in the Punjab. Yenangyaung Field.—The Yenangyaung field maintained its reputation of being one of the most wonderful oil fields in the world. The total production during 1937 was less than in the previous year but the resources of the field as a whole are sufficient to ensure an adequate supply of oil for many years. At the end of 1037 there were 2910 wells producing in the field. Besides a large number of ells drilled to shallow sands, this total includes 180 hand-dug wells, whose continued existenice is one of the interesting features of the field. During the year the deep drilling activities of 1936 in the southern part of the field died down, owing to the disappointing results obtained. On the eastern flank the limit of present economic extension of the oil sands was approximately demareated. Satisfactory results continue to be obtained from gas drives in the leased blocks; gas is also injected for repressuring and storage. Casing policies continue to be carefully designed to protect the oil sands against the danger of flooding by water and, in general, production methods throughout the field are characterized by a realization of the importance of the conservation of oil and gas and the prevention of waste, whether simple or underground. Singu Field.—-In 1937 the increase in the output from the Singu field was continued. This increased production was due not only to the rapid development of the valuable area in the southern part of the field but also to the successful results obtained from the first wells to produce from behind the practically completed river training wall of the Burmah Oil

Jan 1, 1939

The production of petroleum in India (including Burma) increased from 334,811,624 gal.' ill 1936 to 350,322,222 gal. in 1937, the highest figure in the history of the industry. The increase in 1937 was clue to an increase of some 20 million gallons from Singu, 51/2 million gallons from Attack, 11/4 million gallons from Thayetmyo, and 1 mi1lien gallons from Digboi, accompanied by decrcases of 91/2 million gallons from Yenan-gyaung and 2 million gallons from Yenangyat,. The amount of gasoline produced from natural gas during the year was 10,616,313 gal. in Burma and 456,780 gal. in the Punjab. Yenangyaung Field.—The Yenangyaung field maintained its reputation of being one of the most wonderful oil fields in the world. The total production during 1937 was less than in the previous year but the resources of the field as a whole are sufficient to ensure an adequate supply of oil for many years. At the end of 1037 there were 2910 wells producing in the field. Besides a large number of ells drilled to shallow sands, this total includes 180 hand-dug wells, whose continued existenice is one of the interesting features of the field. During the year the deep drilling activities of 1936 in the southern part of the field died down, owing to the disappointing results obtained. On the eastern flank the limit of present economic extension of the oil sands was approximately demareated. Satisfactory results continue to be obtained from gas drives in the leased blocks; gas is also injected for repressuring and storage. Casing policies continue to be carefully designed to protect the oil sands against the danger of flooding by water and, in general, production methods throughout the field are characterized by a realization of the importance of the conservation of oil and gas and the prevention of waste, whether simple or underground. Singu Field.—-In 1937 the increase in the output from the Singu field was continued. This increased production was due not only to the rapid development of the valuable area in the southern part of the field but also to the successful results obtained from the first wells to produce from behind the practically completed river training wall of the Burmah Oil

Jan 1, 1939

By E. S. Bumps, M. Baeyert, W. F. Craig

SOME time ago during a study of impact properties of tempered martensite,1 it was postulated that the consistently good ductility of tempered martensite might be caused by its relatively small and peculiarly shaped ferrite grains. The fer-rite grains of tempered martensite have approximately the same size and shape as the martensite "needles." Thus they form an interlocking mass of needle-shaped grains quite different from equiaxed or lamellar ferrite grain structures. When the common mechanical test methods are applied to steel, variations are often observed in the ductility of specimens that have closely similar hardness and tensile strength values. The ductility so measured appears to be structure dependent. When steel from the same heat has been heat treated to produce different structures with the same hardness, the elongation and reduction of area values from the tensile test and the transition temperature determined by the notched-bar impact test vary according to whether pearlite, tempered martensite, or other structural constituents were produced by the heat treatment. It has been widely recognized that tempered martensite gives a consistently good performance, when tempered to the same hardness as many other structures with which it has been compared. In recent years the isothermal transformation of austenite to specific structural products and the quantitative evaluation of the character of these products with respect to their nature and response to deformation has received considerable attention. The objective of the present study was to pursue somewhat further the dependence of ductility upon structure; specifically, it was desired to ascertain whether ferrite grain structure, including both shape and size of the grains, can account for the consistently good performance of tempered martensite in the notched-bar impact test. It was thought that a simple experiment would indicate whether the ferrite grain structure plays any part in the good ductility exhibited by tempered martensite in contrast to other steel structures with different types of ferrite grains. By determining the impact transition temperature, it was proposed to compare spheroidites having similar carbide particle size and spacing but obtained in such a manner that their ferrite grain structures would be very different. Spheroidite obtained by tempering martensite, with its small, needle-shaped grains, was to be compared with spheroidite from pearlite. If the latter is produced by sub-critical annealing, the ferrite grains correspond to the pearlite colonies. Thus, if the pearlite was not too coarse, the ferrite grains of spheroidite from pearlite are equiaxed in contrast to the needle-shaped grains of spheroidite from martensite. It was thought that the ferrite grain structure of spheroidite from martensite might depend to some extent upon the grain size of the prior austenite. The austenite grain boundaries limit the maximum attainable size of the martensite needles and thus of the ferrite grains in the derived spheroidite. In order to evaluate any possible influence of prior austehite grain size, spheroidites were to be prepared from martensites that had been formed from fine-grain austenite and also from coarsened austenite. As the carbide particle size and distribution were to be essentially alike in the various spheroidites, the difference would be in the ferrite grain size and shape. Thus any marked difference in transition temperature could be attributable to the character of the ferrite grain structure. There are certain considerations in assuming that these spheroidites would be equivalent in all respects except ferrite grain structure, and an attempt was made to take them into account. One of the considerations was the choice of the carbon content of the steel. An approximately eutectoid steel was selected for two reasons. First, the pearlitic structure would contain no proeutectoid ferrite which might complicate the picture by producing a non-uniform ferrite grain structure in the resulting spheroidite. Then, too, the high-carbon content would inhibit ferrite grain growth during the sub-critical treatment. Another factor to be taken into account was the choice of an alloying element to assure a martensitic structure throughout on quenching the impact specimens. Nickel was chosen, because it is a common alloying element and resides in the ferrite both upon its formation from austenite and throughout tempering. The formation of alloy carbides, or even a large solubility of the alloying element in cementite, would have complicated the interpretation by changing the composition of the ferrite .during spheroid-ization. The possibility of temper brittleness was minimized insofar as possible by using a tempering temperature as high as consistent with the 1 pct of nickel in the steel, namely, 1150°F. While it certainly is not claimed that no difference other than ferrite grain structure could exist between the spheroidites, nevertheless, reasonable precaution has been exercised within the limits of steel metallurgy. It is believed that any large difference in transition temperatures would reflect the difference in ferrite grain structure and that relatively good ductility in the spheroidites from mar-

Jan 1, 1951

By John B. Cook

Most of today's open pits take the form of conical-shaped excavations in the relatively flat or undulating terrain surrounding them. Ore is usually hauled uphill from the pit bottom by truck, rail, or skip to crushing, beneficiation, railroad loading, and stockpiling facilities near the edge of the pit. There are, however, a few orebodies whose locations in mountainous terrain causes special problems that generate different technical solutions. LAMCO's 10.5 million metric tons per year high-grade iron mine in the Nimba Range in tropical Liberia is probably one of the most extreme of these exceptions (Fig. 1). At Nimba there is a 2,000-ft difference in elevation between the upper- most levels of the orebodies and the start of the railroad below at the foot of the mountain. Haulage to the crusher is usually downhill at grades of up to 12% dictated by the topography of the rugged terrain. Ore is transported from the crusher down the mountainside by a conveyor sys- tem 10,096 ft long, whose average grade is 18%. The belt is braked by asynchronous generators, feeding power into the local network. The original crusher must be relocated at a lower elevation outside the final pit limit to allow that part of the mountain on which it now stands to be excavated. HISTORY The LAMCO Joint Venture is owned 75% by the Liberian-American- Swedish Minerals Co. (LAMCO) and 25% by Bethlehem Steel Corp. LAMCO is comprised of a 50% interest by the Liberian Government and 50% interest by Liberian Iron Ore Ltd (Fig. 2). This joint venture was launched to develop the high-grade iron ore deposits of the Nimba Range.

Jan 1, 1969

By C. P. Mangelsdorf

The roof truss as a means of secondary or supplemental mine roof support has enjoyed increasing acceptance in recent years, particularly in bituminous coal mines. In those entries where long life is required or doubtful performance from other forms of support seems likely, trusses in many cases have provided the necessary protection for continuing operations. Although relatively expensive and time-consuming in their installation, trusses, particularly with the new resin point anchor system, appear to be justifying their higher premium. It seems inevitable that techniques and equipment for installing them within the cycle will soon be developed. The actual mechanism by which trusses contribute to the stability of a roof is, as yet, poorly understood, and it may be that more than a single mechanism is involved. There are, however, a number of useful observations which can be made concerning the structural behavior of the truss itself, based solely on the mechanics of rigid and deformable bodies. The purpose of this article is to present some of these observations, particularly relating to friction in the system. A few speculations concerning the roof must, of course, be made. From a knowledge of the structural behavior, some insight into the truss-roof interaction may be gained. The concept of the truss is quite simple. As shown in [Fig. 1], it consists of two inclined chords (usually at 45') anchored in holes drilled in the roof over the ribs. A horizontal chord is formed connecting the exposed ends of the inclined chords, either with a third piece or by bending extensions of the inclined chords until they meet in the middle. A distinction can be made between active and passive chords of a truss depending upon the manner of installation. If the inclined chords are fully grouted and the horizontal chord is merely attached to them, it may reasonably be assumed that no significant forces exist in the truss until the roof begins to work. Such would be a completely passive system. On the other hand, if the inclined chords are anchored only at their upper extremities and the horizontal chord is formed in such a way that all three chords can be pretensioned to a significant portion of their tensile strengths then the truss may be regarded as fully active. Combinations of active and passive chords are also possible. * The discussion here is confined to the fully active truss such as the Birmingham steel rod system or the Galis wire rope truss. In both cases, pretensioning is accomplished by tightening of the horizontal chord, some of which tension is transferred to the in-

Jan 1, 1981

By Robert H. Leach

SILVER the whitest of all metals, has been used for thousands of years. Students of antiquity agree that silver, gold, copper, and their alloys were the first metals discovered by man and they have all played an important part throughout the advance of civilization. Native silver has been found in different parts of the world in varying form and size, such as clusters of fine wires in rock cavities, thin sheets along cleavage planes in veins of rocks, and pieces of irregular shape that vary in size from extremely small particles to masses weighing many pounds. Nearly pure silver is found in, the native state but the native metal is more likely to contain copper or gold. Some of the natural alloys closely approximate the compositions of synthetic alloys that are used in the arts at the present time. As these native silver alloys usually are malleable and ductile, it is evident that prehistoric man was provided by nature with metals that he could work, with the crude tools at his command, into simple ornaments or other articles. The relative scarcity of silver combined with its resistance to attack under ordinary atmospheric conditions have been important factors in determining the purposes for which man has used it. Its scarcity and indestructible character have made its possession particularly desirable, and from the earliest times its principal use has been as a measure of wealth and a medium of exchange. The comparatively high value of silver in relation to other commodities makes it possible to transport a large amount of wealth in small bulk, and silver has traveled back and forth over all parts of the world. Even when made into ornamental pieces, such as bracelets,

Jan 1, 1953

The Pinson Mining Co., which will start production in very early 1981, is the fourth Carbon-In-Pulp plant to be put into operation in the United States. The property is located in Humbolt County, Nevada, 38 km (24 miles) northeast of the town of Golconda. The famous Getchell Mine was also near Golconda and was the site of one of the early Carbon-In-Pulp plants in the 1940s. The deposit was discovered in 1971 by Reno based Cordilleran Explorations, which is founded by a consortium of Canadian mining companies. Cordilleran is a partnership consisting of John Livermore and Peter Galli. In 1972 a second but smaller deposit, called "Preble", was discovered at a location 15 miles south of Pinson. During 1980, a decision was made to place the Pinson deposit into production and Pinson Mining Company was formed. Ownership of Pinson is vested in Lacana Mining Inc. , Rayrock Mines, Inc. , Siscoe Metals, Inc., John S. Livermore, Peter E. Galli and Donald M. Duncan. Three distinct but connected ore zones occur at Pinson. Combined reserves of milling ore total 3, 200, 000 tons at an average (undiluted) grade of 4. 12 g per mt (0. 12 oz per st) Au. Initial mining will be from "A" zone which contains 1, 500, 000 tons with an average (undiluted) grade of 5. 8 g per mt (0. 17 oz per st) Au. An additional 5, 500, 000 tons of low grade ore will be mined from the Pinson deposit and processed by heap leaching. Mining reserves at Preble total at least 1, 500, 000 tons grading 2. 7 g per mt (0. 08 oz per st) Au. Production plans for the Preble deposit have not been formulated at the date of writing. Gold mineralization at both deposits is finely disseminated as sub micron sized particles. The ore at Pinson is structurally controlled and occurs in an Ordovician limestone-siltstone unit. Much of the ore has been silicified to a jasperoid. The ore zones have been entirely oxidized. Preble ore occurs in the Cambrian formation in a carbonaceous, limey shale. Only the upper part of the Preble is oxidized and amenable to conventional cyanide leaching. The Pinson ore body is adjacent to the mouth of Granite Creek in the Osgood Mountains at an elevation of 1, 615 m (5, 300 ft) with the mill being 1. 2 km (3/4 mile) from the mine at an elevation of 1, 495 m (4, 900 ft). Mine development work began in May of 1980 with ore being stockpiled for later processing. Pertinent factors affecting

Jan 1, 1981

By John Roberts

THE Federal income tax law permits as a deduction in determining net income "in the case of mines, . . . a reasonable allowance for depletion and for depreciation of improvements, according to the, peculiar conditions in each case, based upon cost, including cost of development not otherwise deducted: Provided, that in the case of such properties acquired prior to Mar. 1, 1913, the fair market value of the property (or the taxpayer's interest therein) on that date shall be taken in lieu of cost up to that date." The law provides for a reasonable allowance but the regulations provide for a definite method of computation that possesses more the virtue of simplicity than that of reasonableness. Article 210 of Regulations 45. reads: "When the cost or value as of Mar. 1, 1913, or within 30 days after the date of discovery of the property shall have been determined, and the number of mineral units in the property as of the date of acquisition or valuation shall have been estimated, the division of the former amount by the latter figure will give the unit value for purposes of depletion, and the depletion allowance for the taxable year may be computed by multiplying such unit value by the number of units of mineral extracted during the year." This is simple, but is it reasonable? The intent of the law is clearly that the cost of the ore in the ground shall be considered as part of the cost of the same ore when removed and sold. The regulations fail to carry out that intent, because of the unwarranted assumption that all the ore in the mine cost the same amount per ton. This is what gives the Treasury Department's method its simplicity, but at the same time robs it of its reasonableness because the assumption is contrary to fact.

Jan 1, 1921

By A. T. Shurick

THE present economic crisis in bituminous coal is substantially the most insidious, and critical, in the modern history of the industry. The large consumption deficit that has gradually developed (almost unawares), has culminated in a situation that has forced home the urgent necessity for prompt and radical remedial measures, such as the various mergers now in course of negotiation. Conditions today are sufficiently comparable with those in the iron and steel industry, preceding the formation of the United States Steel Corpn., to suggest the possibility of a sweeping super-consolidation, that all but staggers the imagination. The important function of the banker in this, and lesser projects, is too well known to require comment, and it is important that we understand clearly just what these functions are. Certain features in banking practice came up for consideration in connection with a rather exhaustive economic study into the prospective future of the coal industry, upon which I was recently engaged for an Eastern bituminous interest. This survey was made for the purpose of effecting a decision on certain pressing questions of policy, involving considerable capital expenditures, that would be compatible with the flattening out in the curve of production in recent years. An examination of the TRANSACTIONS, and the coal literature generally, failed to disclose any pertinent, and authoritative data, on this subject. This was more or less characteristic of the whole survey, which had involved a large amount of original research, and measures were taken to procure the required information. The following notes have been compiled largely from the data thus collected, supplemented with material, suggestions and criticisms, by several of the larger banking houses active in coal, together with personal memoranda of my own.

Jan 1, 1928

By C. A. Pierce

STUDIES of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its com-mercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft. in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft, of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding for-mations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresses."1

Jan 1, 1938

EVERY English-speaking mining, engineer or geologist knows that some terms used by his profession are not rigid but vary regionally; for example: what is called a vein by some, is called a lode by others and is known as a reef to their Australian colleagues. There are parallels in, the German language. Since, in addition, the meaning of some words may change considerably in 450 years-and other words may disappear completely-and not only the terminology but the concepts of a science are subject to drastic changes over such a long period of time, translating the Bergbüchlein posed some interesting problems. Old German texts and glossaries such as C. T. Delius' Anleitung zu der Bergbaukunst (1773), Minerophilus' Neues and Curieuses Bergwercks-Lexicon (1730), and H. Veith's Deutsches Bergwörterbuch (1871) proved useful sources of information when defini¬tions of obscure terms were needed. The task of translating was made even more challenging by the author's personality. As Ulrich Rülein von Kalbe was primarily a physician, his information must have been mostly secondhand. Since the nomenclature of the miners of Saxony, where he gathered his material on silver ores, undoubtedly varied from that of the German miners in Hungary, for instance, who probably supplied him with data on gold ores, it is not astonishing that he is not consistent in his use of some expressions. To give an example: there is every indication that Flöz and schwebender Gang (see footnote p. 21) are used interchangeably in spite of his occasional disapproval of such usage. It is obvious that he was an educated man with a questing and active mind and, although he apologizes-not wholly sincerely, one might suspect-for the simple

Jan 1, 1949

By D. G. Swarthout, J. W. Savage, R. W. Guard

The Nb-N constitution diagvam has been examined from 1100° to 1450°C at 1 atm N2 pressure. On the basis of- our work plus that of Brauer and coworkers the stable nitvide Phases are: a) a solid solutlion, basic niobium (bcc) with nitrogen contained interstitially; NbN,, x = <0.40; b) ß NhNx,x = 0.39 to 0.45; hexagonal (W2C type) (NbzN); a =3.058A,c = 4.961 + 0.001A c) y NbNx x = 0.75 to 0.80; tetragonal (distorted NaCl type) (Nb4N3); a = 4.386A,c = 4.332 + 0.001A; d) 6 NbN,, x = 0.88 to 0.91; cubic (NaCl type); a = 4.3885 + 0.0007A; e) E NbNx x = 0.92 to 1.00; hexagonal (Tip type); a = 2.958A, c = 11.272 * 0.0015A. In addition, a metastuble transition phase 6&apos; has been observed and occurs only during the transition 6 — E. 6&apos; NbN has these distinguishing parameters: NbNx,x = 0.96; hexagonal (anti-NiAs type); a = 2.94A, c = 5 .46A. The high-temperature phase fields in the system are governed by two reactions: a) 6 + Y + E, a entectoid reaction occurring at 1270" ± 20° C; b) o + N2 = E, a 2 012 1 reaction occurring at 1370" ± 20° C. As part of a study of the electronic low-temperature. properties of transition metal nitrides, a number of specimens of niobium nitride were prepared. Preliminary observations on these specimens showed several points of disagreement with data already in the literature. It was, therefore, decided to determine the constitution diagram for the Nb-N system between 1100" and 1450°C. The objective of this research was to define the temperature and composition regions of stability of the various phases and to explain the differences among previously proposed diagrams. Review of Previous Literature. The research on the Nb-N system to 1964 has been summarized by storms.&apos; Although he does not present a phase diagram, his review covers the research on the system thoroughly. One of the earliest works on NbN is that of Ascher-mann and coworkers2 who studied the superconductivity of the cubic 6 NbN. Subsequent work by Horn and ziegler,3 Cook, Zemansky, and Boorse,1 Rögener:5 Schroder6 and sellmaier7 has qualitatively confirmed the first results on superconductivity, although their methods of preparation differed considerably. The constitution diagrams proposed for the system by Brauer and Esselborn8 and Elliott9 are shown in Fig. l(a)and (b). The diagram in l(a) has been modified by more recent results in Brauer&apos;s laboratory (private communication). Although 6&apos; is shown on this diagram, Brauer has indicated that he now believes 6&apos; to be a metastable phase in the temperature range shown. The diagram of Elliott, Fig. l(b), is based primarily on the results of Elliott and Komjathy10 on ni-trided niobium strip or rod specimens examined by X-ray diffraction and metallography. It will be noted that these proposed diagrams are in conflict with respect to the temperature and composition ranges of

Jan 1, 1968

By R. A. Salathiel

A new synthetic material has been developed which is highly effective in treating drilling muds to reduce filtration rate. The material is the soluble salt of a very high molecular weight condensation product of sulfonated phenol and formaldehyde (SPIF). Laboratory tests show that SPIF is effective in muds of all salinities varying from fresh water to saturated salt water. Alkaline materials. such as soda ash or caustic and quebracho, may be used in combination with SPIF to advantage, and are essential in muds containing saturated salt water. In a field test where the water used in the mud had a salinity of about one-half that of sea water, SPIF in combination with caustic and quebracho made a very satisfactory mud. SPIF does not ferment. but due probably to additional polymerization a slight decrease in effectiveness is found when it is subjected to high PH and high temperature for a long time. INTRODUCTION Drilling mud is essential in rotary drilling. The influence of variations in the different properties of a mud on its ability to perform the various functions in drilling of wells is thoroughly understood in some cases and poorly understood in others. For instance, the function of mud density in restraining high pressure fluids is simple and well known. On the other hand. while the value of low filtration is widely recognized, it is seldom possible to determine precisely what filtration rate is required for the mud to perform its functions properly. Filtration rate is important because it influences the ease of moving tools in or out of the hole. Filtration rate also affects the stability of the bore hole walls, which are subject to softening and degradation by aqueous filtrate. Difficulties in rotary drilling are often avoided by using low-filtration muds. Treatment of fresh-water muds to provide moderately low filtration rates usually consists of adding chemicals to improve the dispersion of the clays. To provide very low filtration rates, organic colloidal materials are added. Among the materials hat are used in this way are starch, natural gums, and altered celluloses. In muds that contain large amounts of salt or calcium or magnesium ions, the clays are coagulated and, as a consequence, the filtration rate is undesirably high. In such muds organic colloids are of great importance. LIMITATIONS OF PRESENT FILTRATION ADDITIVES Starch and water-soluble gums are widely used as filtration control agents. Starch is the most important material of this kind being used. It has the advantage of relatively low cost. It is effective in promoting low filtration rates, not only in fresh water muds, but also in muds containing large amounts of salts. However, both starch and natural gums are subject to fermentation and must be preserved from damage caused by microbiologic attack. Also, both starch and natural gums tend to increase the mud viscosity undesirably. Furthermore, the quantity of material required may be quite large. This is especially true when substantial amounts of salts are present. In such a case small addition* of starch may increase rather than reduce the filtration rate of the mud. Carboxy-methyl-cellulose, a chemically altered form of cellulose, has some advantages over starch. It is effective in smaller concentrations and does not increase the viscosity as much as

Jan 1, 1952