Search Documents

By P. Shahinian, H. H. Smith, M. R. Achter

Crack growth rates are measured at elevated temperature in a resonant fatigue machine from vibration frequency decreases calibrated in terms of crack depth. Crack growth rates in Type 316 stainless steel at 500º and 800°C show a sharp increase with oxygen pressure in an intermediate pressure range and little or no change at high and low pressures. At 500°c, I torr of oxygen reduces the fatigue life by almost a factor of 100 in comparison to that in vacuum and raises the growth rate of shallow cracks by the same At At 800°C the effects are smaller. Changes in slope in the crack growth rate curves are discussed in terms of a model in which rates of surface production and of surface coverage by gas are compared. The use of a calculation method in which the surface exposure time is equal to X/v, where x is the interatomic spacing and v is the growth rate, makes it possible to obtain order of magnitude agreement at 500°C between the observed pressure and the predicted pressure at these slope changes. At 800°C oxidation becomes a .factor and the data cannot be treated by simple adsorption theory. THE decrease in the fatigue life of metals as a function of gas pressure usually follows a stepped curve with virtually all of the decrease concentrated in a sharp drop in a transition zone at intermediate pressures and little or no change at low and high ranges. A number of models, differing in the details of the mechanism, have been offered to explain the shape of the curve. Measurements of crack growth in aluminum as a function of gas pressure by Bradshaw and Wheeler' and Hordon2 demonstrated opportunities for quantitative comparison to evaluate the proposed models. Since comparable data were lacking at high temperatures, in the present work rates of crack propagation were measured in Type 316 stainless steel at 500" and 800°C as a function of oxygen pressure. Choice of this material was dictated by two considerations; it is stiff enough at these elevated temperatures to resonate with the regenerative drive on our fatigue machine and it is known to display a large effect of environment. A new method of calculation is described to predict the gas pressure at the critical point. EXPERIMENTAL PROCEDURE Because of the difficulty of measuring crack depths directly at high temperatures, an indirect method was developed based on the decrease in the resonant frequency with the growth of a crack. A reversed bending, constant amplitude fatigue machine, described previously,3 vibrates a specimen at its resonant frequency, automatically records any changes in it and shuts itself off after it has reached a preset value of frequency decrease. The record of frequency change is used to determine the rate of crack growth. Sheet type specimens of Type 316 stainless steel, Fig. 1, incorporated a sharp, shallow notch to localize the formation of a single crack. After machining, they were annealed in a vacuum of l0-6 torr either at 1066" (lot A) or 871°C (lot B) and then electropolished in an acetic-chromic acid solution. Bending strains were measured at 500" and 800°C by an optical technique4 and reported as total strain without correction for the notch. At 500°C, the 0.141 pct strain was 0.085 pct elastic and the remainder plastic. At 800°C the 0.062 pct strain was all elastic. To convert frequency decrease to crack length, calibration curves were obtained by interrupting the vibration at stated intervals of frequency decrease. The crack depth was measured microscopically at a magnification of X400 and reported as the average of the measurement on each edge. Some specimens were sectioned for crack measurement while others were returned to the machine and fatigued further. There was good agreement between the two methods. Before beginning the vibration, the vacuum chamber was first evacuated cold to 1 x 1O-6 torr, then heated to the operating temperature and held there until the pressure was again reduced to 1 x10-6 torr at which time oxygen was introduced to the desired pressure. In this investigation the vibration frequency was nominally 10 cps and a decrease of 0.6 cps was taken as the failure point. The choice of the frequency decrease to represent failure has no appreciable effect on the fatigue life because the crack is growing very fast at this point.

Jan 1, 1970

By David Keys

THE actual procedure in estimating depth of overburden from mag-netic observations made on the surface will vary with the form of the deposit and any theoretical discussion will apply only so far as the form of the deposit conforms to the mathematical premises on which the theory is based. Since the shapes of natural deposits in the field cannot be expressed rigorously in mathematical form, the best that can be done is to assume some simple form and deduce results. Fortunately many small variations in form produce only slight changes in the estimated depth of overburden, therefore the methods have a definite practical value. For the theoretical treatment, magnetic ore deposits may be divided roughly into three classes, depending upon whether the magnetic anom-alies may be considered to arise from (1) a single magnetic pole, (2) a dike or (3) a magnetic doublet. Particular cases, falling under one or other of these classes, have been discussed by different authors.1-4 In general, it may be stated that when the magnetic effects as measured on the surface are due only to one pole of the body, the other pole being so remote that its effect may be neglected, the resultant anomaly F at any point will vary as the inverse square of the distance r of the point from the pole, which may be expressed mathematically by F = k/r2, where k is a constant. When the deposit occurs in the form of a long, thin dike, the resultant anomaly will be of the form F = k'/r and when the deposit is in the shape of a lens, so that both poles have an appreciable effect on the surface, the result will be similar to that caused by a magnetic doublet, and the form will be F = k'/r3. The particular class under which a deposit falls may be deduced from the results of the magnetic survey. The second class is readily found, but there may be difficulty in deciding between the first and third. Isody-namic contours of both the vertical and horizontal anomalies will often be a good guide in making a correct decision.

Jan 1, 1937

By Fred Jones

The Cripple Creek district is in Teller County, Colo., about 18 miles in an air line west of Colorado Springs and at an elevation of 10,000 It. A line drawn through Colorado Springs and Pikes Peak will, if continued, about pass through the district. The character of the country generally is rolling, with few trees and little snow fall. The annual precipitation is about 20 in. All the water used by the mines is supplied by the Altman Water Co., which pumps from the west slope of Pikes Peak. Gold was discovered in 1891, since which time the district has produced $411,000,000. The peak of production was reached in 1900 and amounted to $25,000,000. At present the production amounts to about $400,000 per month. Geology In general, the geology of the district is simple; ash veins and dikes traverse a volcanic plug of breccia. The ore occurs as enriched spots along these dikes and veins. The dikes represent the most recent extrusions and consist of basalt and phonolite. (For a complete geological description reference is made to Professional Paper 54, 1906, of the U. S. Geological Survey.) The ore consists of small parallel seams of high grade. In only a few cases is the gold disseminated through the rock; much of the gold in the broken ore is found in the fines. The wall rock is hard blocky granite or breccia. About 25 per cent. of the rock mined is shipped as ore to the Golden Cycle mill at Colorado Springs. The height of an ore deposit is usually several times its length. Few flat oreshoots have been found. The veins are all steep and have a dip of 70 to 80°. Development The claims are all 300 by 1500 ft. and are held by location or patent. All mining is done through shafts, one of which has reached a depth of 2600 ft. The main working shafts are 41/29 by 1335 It. and are made up of three compartments, each 4 by 41/2 ft. in the clear. They are timbered with 10-in. Oregon posts and plates and 8-in. spreaders. Two compart-

Jan 1, 1925

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The microhardness of single crystals of tungsten disilicide has been investigated by the Knoop method. The average random room-temperature hardness of the WSi, matrix was 1350 kg per sq mm. Hardness crnisotropy was noted with respect to plane and indenter orientation as determined by single-crq.stal X-rny studies. Annealing at 1600" and 1800°C decreased the average hardness to 1310 and 1230 kg per sq tnm, respectively, and produced a second phase identified by X-ray diffraction and electron-microprobe analysis to be wSio.7. Ball-impact experiwzents produced rosettes at 850°C. Optical and electron microscopy showed evidence of slip and cross slip and twinning produced by microhardness indentations. Prismatic (100), [001] slip was found and cor~elated with hardness data. THE present study was undertaken to investigate the hardness anisotropy of as-grown and annealed single crystals of tungsten disilicide. The existence of the silicide WSiz in the W-Si system has been well-established and its structure thoroughly investigated zachariasen2 found WSi, to have a tetragonal C type of structure, similar to that of MoSi, with lattice parameters a = 3.212A, Kieffer et al. studied the W-Si system and measured the density and microhardness (at a 100-g load) of both polycrystalline WSi, and WSi,.,. The values found were 9.25 g per cu cm and 1090 kg per sq mm for WSi,, and 12.21 per cu cm and 770 kg per sq mm for WSi0.7, respectively. According to Samsonov et a1.5 the microhardness of polycrystalline WSi2 is 1430 kg per sq mm (at a 120-g load). EXPERIMENTAL The WSi, single-crystal boules investigated in this paper were grown by a Verneuil-type process using an electric arc by the Linde Division of the Union Carbide Corp.6 The largest specimens were 8 mm in diameter by 16 mm long. The crystals had an average density of 9.01 g per cu cm with a tungsten • silicon content of 99.9 wt pct. The major impurities were: 87 ppm O, 41 ppm N. 54 pprn C, 500 ppm Zr, 50 ppm Na, and 50 ppm Mn. The crystals were silicon-poor, the average silicon content being 22.20 pct (stoichiometric value is 23.40 pct), and tungsten-rich, the average tungsten content being 77.70 pct (stoichiometric value is 76.60 pct). As-received single crystals were ground and analyzed by powder X-ray diffraction technique using Cu Ka radiation. Laue and layer line rotation patterns were obtained on cleaved sections of WSi, single crystals. Electron-microprobe traverses of representative crystals were done using a Phillips-AMR electron microanalyzer. Carbon replicas were used to prepare electron micrographs. This work was done with a JEM-6A electron microscope. Prior to the metallographic examination, the specimens were mounted in Lucite and then polished for short times on polishing wheels using 9-, 3-, and 1-p diamond-grade pastes. Finally they were fine-polished with Linde A powder for 24 hr on a Syntron vibratory polisher. The samples were etched with 4H 2 O:1HF:2HNO3, which is a medium fast-acting etchant. The combination 1HF:2HNO3:5 lactic acid is also a satisfactory etchant. Annealing runs for selected specimens were made at 1600" and 1800°C for 3 hr at 1.0 to 3.0 x 10-5 mm Hg. A Brew tantalum resistance furnace with WSi2 powder for setters was used. The WSi2 powder was the same as that used for the crystal growth. Temperatures were measured with a calibrated W, W-26 pct Re thermocouple and a microoptical pyrometer. Powder X-ray diffraction, emission spectrographic, and electron-microprobe analyses were done after the annealing runs. For microhardness measurements a Tukon Microhardness Tester Type FB with a Knoop indenter was used. Although measurements were taken at loads ranging from 25 to 1000 g, the 100-g load was chosen as the standard load. All measurements were taken at room temperature. Only indentations of cracking classes 1 and 2 were considered.' DISCUSSION OF RESULTS Powder X-ray diffraction analysis showed the as-received crystals to be single-phase WSi2. Laue and layer line rotation patterns obtained on cleaved sections of WSi2 single crystals proved them to be tetragonal WS 2 2 The results also indicated that the c axis of the crystal was oriented parallel to the boule or growth axis. Electron-microprobe traverses across the matrix of the as-grown crystals showed them to be homogeneous WSi,. Optical and electron microscopy of etched crystals, however, revealed that they contained minute amounts of the "golden" and the "blue" second phases as opposed to the "white" or WSi2 phase. These two second phases were concentrated in inclusion and etch-pit

Jan 1, 1965

By Y. A. Chang

Heat content values of tantalum monocarbide and tungsten monocarbide have been determined from 325" to 985°K by means of a drop-type diphenyl ether calorinzeter. Based on the values obtained in the present study and those available in the literature, best values lected and computed from 298. 15°K to temperatures close to their respectiue melting points. At temperatures higher than 1700°Kfor TaC and 27000 K for WC, values of Cp and related thermodynamic quantities were extrapolated based on the two Debye parameters: one corresponds to the metal sublattice and the other to the carbon sublattice. The contrzbutzon In the total specific heat due to lattice dilation was evaluated using the Nernst-Lindemann relalionship. The calculated values of Cp were in good agreement with the In view of their refractoriness, tantalum monocar-bide (TaC) and tungsten monocarbide (WC) are of con- experimentally determined ualues. Furthermore, the calculated values of the absolute entropies at 298.15"K were 5.03 and 4.15 in comparison to the experimental values of 5.05 and 4.15, all expressed in the unit of cal per degg-atom. Using the same Debye parameters, values of the linear coefficients of ther mal expansion for TaC and WC were calculated from absolute zero to their respective melting points using the Grüneisen equation. The calculated values are in excellent agreement with the experimental values available in the literature. Finally, the values of the bulk modulus of TaC from room tenzperature to temperature near its melting Point were also calculated using the equation recently derived by Anderson. No cot~ipari-son between the calculated and experimental values can be made due to lack of experimental data. siderable practical interest. In order to completely define these materials, it is necessary to know their thermal properties as a function of temperature. Tantalum rnonocarbide having a NaCl structure (B-1 type) melts congruently at 4250PK,1 while tungsten monoearbide with a simple hexagonal structure (Bh type) melts per itectically at 3049°K into melt and graphite.2 In the present study, the heat content values (from which

Jan 1, 1968

By P. K. Foster, A. McNabb

A consideration of the literature shows the inadequacy of Fick's Laws to describe the diffusion of hydrogen in steels below 400°C. These laws are modified an the assumption that hydrogen is delayed at fixed sites in the lattice. Approximate and exact solutions of the resulting nonlinear system are derived for simple geometrical shapes. The results qualitatively account for the observed anomalous behavior. Experimental methods for verifying the theory are suggested. 1 HIS paper presents a new analysis of the diffusion behavior of hydrogen in steel based on a physical model which supposes that hydrogen atoms wander in a random manner through the crystal lattice, but tend to get trapped or delayed at certain fixed sites uniformly distributed throughout the metal. These sites, which will be called traps, are regarded merely as potential wells of significantly greater depth than those encountered in regular regions of the crystal lattices and no assumptions are made concerning their nature or origin. The results of experimental studies of the diffusion of hydrogen in iron and steel have usually been reported in the literature in terms of a diffusion constant D derived under the assumptions that the hydrogen concentration C is governed by Fick's laws.1 Fig. I is a composite of published graphs of the man. ner in which the values of D, so derived, vary with temperature. It is convenient to consider this material in two categories; the high temperature results above 400°C, and the results at lower temperatures. The graphs 2, 3, 4, 5 in the first class lie within a factor of three of each other and are relatively consistent compared with the low-temperature values. There is an increasing divergence in values of D with decreasing temperature till at room temperature they are spread over three orders of magnitude. Small values of D have been obtained for work-hardened specimens.' It is evident that D is a function of other variables besides temperature in this range and that these neglected variables are in some way connected with the work hardening experienced by the specimen. In view of evidence for an interaction between hydrogen in solution and dislocations9'10 and adsorption on crack surfaces,' some doubts must be entertained about the validity of Fick's laws and their associated physical model of noninteracting particles in random motion through the medium. More direct evidence of their inapplicability to the diffusion of hydrogen in steel was first produced by Darken and smith." Consider the permeation of hydrogen through a plate of thickness a under a boundary concentration Co at the ingoing, and zero at the outgoing, face. If Fick's first law1 is valid, the steady state flux P, through unit area is DCo/a. In addition, the concentration C varies linearly throughout and Qo, the mean quantity of hydrogen in the medium, is co/2. Compare Qo with Q1 the mean quantity required to saturate the same specimen to a uniform concentration G. In this case Ql = Co and hence the ratio

Jan 1, 1963

By R. W. Coughlin, W. U. Ault

Experiments in laboratory and mine have clearly demonstrated the usefulness of radioactivity detection for directly measuring the potassium content of potash ore as mined. This paper presents the results of these tests and documents the design of a system for automatically grading and sorting potash ore on the basis of radiation detection. It is shown how the experimental results in the subject mine lead directly to the design of this kind of an automatic control system. The system is capable of grading the ore with an accuracy of approximately ±2% K20 content or better. Due to the usual stratification of the ore body, mining potash seldom presents an extreme problem of gangue separation. Nevertheless, it is frequently necessary to transport within a potash mine and even hoist to the surface considerable quantities of halite and other valueless materials. Up to recent times it has been customary to recognize and route these materials by simple visual and manual techniques. However, the work reported here clearly demonstrates that it is now practical and economical to improve upon these techniques by continuous measurement1 of the naturally occurring radioactive isotope, potassium-40. It was the purpose of the work reported here to investigate this technique and assess its applicability. LOCALE OF EXPERIMENTS The work described here was carried out in a potash mine in Carlsbad, N.M. At the working face of this mine the potash ore is freed by blasting; it is then transported a short distance by shuttle car to a moving-belt system which conveys it to the main shaft where it is hoisted to the surface. Quantities of gangue which are also produced in the mining operation are disposed of in mined-out sections of the mine where possible. Otherwise, this material which contains only a small percentage of potassium (as K2O) must also be transported by the conveyor-belt system to the main shaft and then hoisted to the surface and discarded. With this situation, any measuring device for automatic control purposes must be capable of clearly distinguishing between gangue containing insignificant amounts of K2O and ore containing larger percentages of the same mineral. The conveyor-belt system transports the material from the mine face to a rotary crusher and then to temporary storage pits at the main shaft. This is shown in Fig. 1. Upon leaving the conveyor belt the material enters either one of the two storage pits according to the position of a manually operated gate. It was decided that all experiments should be carried out at the conveyor belt between the crusher and gate with a view to the possibility of providing a signal which could operate the gate automatically. THEORETICAL BASIS AND LABORATORY EXPERIMENTS In principle it is possible to grade potassium-bearing ore on the basis of radioactivity. Natural potassium contains 0.012% K40, which is radioactive with a half-life of 1.3 x 10' years. Although about 89% of the K40 disintegrates to Ca40 by beta decay, the other 11% changes to Ar40 by electron capture and the emission of gamma rays. Unlike the ß-rays which are readily absorbed in the first few millimeters of ore surrounding the disintegrating nucleus, the y-ray photons will escape from an ore sample several inches in size. A detector rigidly mounted under a conveyor belt loaded with potash ore will intercept some constant fraction of all the photons emitted from the ore within its field of view. Under these

Jan 1, 1968

By V. R. Garfias

A survey of the resources of mineral fuels, coal, petroleum and natural gas presupposes a clear distinction between the known amount underground and the "proven reserves"; the'portion that can be economically brought to the surface and made available for utilization. Only a fraction of the coal and petroleum in producing fields is or can be economically brought to the surface and not all of this is economically utilized; also, although practically all the natural gas can be economically recovered and utilized, in actual practice a large part of the total volume that reaches the mouth of the wells is wantonly blown into the air and wasted. It is thus estimated that of the total amount of coal underground about 40 per cent remains unrecovered, or is otherwise wasted, before it reaches the consumer; that only some 25 per cent of the petroleum in proven fields is actually brought to the surface; and that even if practically the entire volume of natural gas can be economically utilized, in actual practice close to 25 per cent of the total produced is now absolutely wasted. And the dissipation of this gas, unwarranted as it is, not only diminishes the gas supply but diminishes also the proven reserves of petroleum from such fields as the Panhandle of Texas, where petroleum and natural gas are produced simultaneously. Many factors affect the estimates of the proven reserves of mineral fuels, such as the capacity and nature of the reservoir, its depth, the quality of the product, the efficiency of recovery, the price of the fuel and its byproducts, etc., etc., but superseding at times all of these in connection with petroleum and natural gas deposits is the effect of "subsoil ownership" on the rate and methods of exploitation of the deposits. As a result it should be a comparatively simple matter to eliminate waste and overproduction, and thereby increase the proven reserves of petroleum and natural gas, in Russia, Iran and Iraq, where the subsoil rights are nationalized, or in any country in which there is or can be quickly established an effective legal control of the underground deposits and the manner of their exploitation. It has been and it is now, on the other hand, almost an impossible undertaking to intelligently regulate the petroleum and natural gas production in the United

Jan 1, 1935

By William P. Blake

THE phenomena of concentric arrangement of minerals in rock-masses, generally known as "orbicular structure," have of late received much attention from investigators. Lawson, of the University of California, has described the orbicular gabbro at Dehesa, San Diego county, Cal. Kessler and Hamilton, of Stanford University, working independently upon the same subject, published their descriptions,2 giving also a list of many other localities in Europe and America where orbicular rocks are found, adding copious references to the literature of the subject. The orbicular diorite of the type locality in Corsica., familiar to mineralogists and petrologists under the name "Napoleonite," was described by Vogelslang in 1862.3 Chrustschoff, of St. Petersburg, has also given much atten¬tion to the subject, and is the author of a classification of the various known forms of orbicular structure.4 No complete and satisfactory explanation of the origin of or¬bicular aggregations in rocks has yet been offered. The patent fact is generally recognized that the constituent minerals have crystallized from a more or less molten or plastic magma, but why these minerals should be arranged in concentric spheres or crusts has not been clearly shown. Vogelslang, for example,

Jul 1, 1905

By E. O. Kirkendall

The investigation reported herein was undertaken to obtain data to supplement those presented in an earlier paper,l particularly for longer times at a higher temperature. This information may further develop our knowledge of the mechanism of diffusion in substitutional solid solutions. Diffusion of solute atoms interstitially dissolved is not difficult to visualize: it can take place without much disturbance of the solvent atoms. The mechanism of diffusion of solute atoms substitutionally dissolved is not so easily understood. Many theories have been advanced. Rosen-hain,2,3 Frenkel,4 Smekal,5 Langmuir,3,6 Steigman, Shockley and Nix,' and Johnson8 all proposed theories to explain diffusion. Langmuir's proposed mechanism consisted of a simple cyclic interchange of atoms involving an interchange in lattice positions of four or more atoms. This mechanism, accepted by the author at the time of his previous publication,1 and apparently quite generally accepted, required a net exchange in positions of both solute and solvent atoms in equal numbers. In other words, the rate of diffusion of the solvent and solute atoms would be the same. That this cyclic interchange in lattice positions of solute and solvent atoms in equal numbers is the only true mechanism of diffusion is denied by the evidence presented in this paper. Experimental Procedure This modification of similar procedure1 will be outlined briefly. The method consisted of the following steps: I. A pure Muntz metal (60.6 per cent Cu, 0.1 per cent total impurities) that was almost all beta brass at 780°C. was chosen. 2. The brass was turned between centers in a lathe to a diameter of 0.5965 inches. 3. After the brass was cleaned, it was electroplated with pure copper to a diameter of about one inch. 4. The sample was heated slowly to 400°C. under reduced pressure and held at that temperature for 4 hr. to remove occluded gases. It was then cooled to room temperature. 5. The sample was heated to 780°C. ± 3°C. and held at that temperature for different lengths of time; then quenched. Samples were cut off each time after quenching. Metallographic samples 1/4 in. thick were removed at I hr., 6 hr., 24 hr., 96 hr. and 701 hr. After 96 and 701 hr. samples of about I in. were removed for X-ray analysis. 6. The metallographic samples were polished on the cross section and photomicrographs were taken. 7. The I-in. samples were polished and etched on both ends. With the aid of a microscope each was carefully mounted in a four-jaw chuck in a lathe, so that they could be accurately bored for an arbor. 8. Turnings were taken for each X-ray sample. After each set of turnings, the sample was heated in an oil bath for about 1/2 hr. at 300°C. It was then etched in 25

Jan 1, 1942

By E. O. Kirkendall

The investigation reported herein was undertaken to obtain data to supplement those presented in an earlier paper,l particularly for longer times at a higher temperature. This information may further develop our knowledge of the mechanism of diffusion in substitutional solid solutions. Diffusion of solute atoms interstitially dissolved is not difficult to visualize: it can take place without much disturbance of the solvent atoms. The mechanism of diffusion of solute atoms substitutionally dissolved is not so easily understood. Many theories have been advanced. Rosen-hain,2,3 Frenkel,4 Smekal,5 Langmuir,3,6 Steigman, Shockley and Nix,' and Johnson8 all proposed theories to explain diffusion. Langmuir's proposed mechanism consisted of a simple cyclic interchange of atoms involving an interchange in lattice positions of four or more atoms. This mechanism, accepted by the author at the time of his previous publication,1 and apparently quite generally accepted, required a net exchange in positions of both solute and solvent atoms in equal numbers. In other words, the rate of diffusion of the solvent and solute atoms would be the same. That this cyclic interchange in lattice positions of solute and solvent atoms in equal numbers is the only true mechanism of diffusion is denied by the evidence presented in this paper. Experimental Procedure This modification of similar procedure1 will be outlined briefly. The method consisted of the following steps: I. A pure Muntz metal (60.6 per cent Cu, 0.1 per cent total impurities) that was almost all beta brass at 780°C. was chosen. 2. The brass was turned between centers in a lathe to a diameter of 0.5965 inches. 3. After the brass was cleaned, it was electroplated with pure copper to a diameter of about one inch. 4. The sample was heated slowly to 400°C. under reduced pressure and held at that temperature for 4 hr. to remove occluded gases. It was then cooled to room temperature. 5. The sample was heated to 780°C. ± 3°C. and held at that temperature for different lengths of time; then quenched. Samples were cut off each time after quenching. Metallographic samples 1/4 in. thick were removed at I hr., 6 hr., 24 hr., 96 hr. and 701 hr. After 96 and 701 hr. samples of about I in. were removed for X-ray analysis. 6. The metallographic samples were polished on the cross section and photomicrographs were taken. 7. The I-in. samples were polished and etched on both ends. With the aid of a microscope each was carefully mounted in a four-jaw chuck in a lathe, so that they could be accurately bored for an arbor. 8. Turnings were taken for each X-ray sample. After each set of turnings, the sample was heated in an oil bath for about 1/2 hr. at 300°C. It was then etched in 25

Jan 1, 1942

By J. A. Thompson, M. A. Mayers

IN recent years, the problem of damage to coke-oven walls by expanding coal charges undergoing carbonization has engaged great attention on the part of research workers in this field, and has led to the development of many devices for estimating these pressures.1-14 Only in Russell's method11 and in the Koppers ovens7 are conditions quite similar to those in commercial ovens. Tests even in these ovens are empirical because no information has been published to permit an evaluation of "scale effects." Owing to the relatively large wall area in these test ovens, the average wall pressure determined may be lower than that existing in localized areas. This factor may be compensated for in part by the testing of coal charged into the test oven at a bulk density that is as high as the highest that is believed to exist in commercial ovens. Both of these lacks might be filled by the development of an adequate gauge for the direct measurement of wall pressure exerted by the charge in commercial coke ovens in normal operation. Previous attempts to elaborate such instruments7,15 have resulted in units which, because they had to be water-cooled, probably produced changes in the conditions of carbonization, and which had to be removed from the oven before carbonization was complete, to avoid their destruction. Late in 1941 the Coal Research Laboratory undertook to develop such a gauge, in which gas pressure was balanced against the charge pressure and which thus would not require water cooling, on a suggestion made in 1937 by one of the present authors and William B. Warren, a former member of the Laboratory staff. The gauge heads themselves were to be simple and cheap enough so that they might be discarded after each run if seriously damaged. This would permit them to be left in place throughout the carbonizing period, when they could be pushed out with the coke. The basis of the design, of which the latest exemplification is shown in Fig. I, was that as the internal gas pressure within a flexible metal envelope was increased, the flexible wall would move away from a stop when the gas pressure just overbalanced the charge pressure. If the stop were an insulated electrical contact, the point of balance could be indicated by the breaking of an electric circuit. It was anticipated that, while the instrument must operate at high temperature, the presence of a strongly reducing atmosphere throughout the carbonizing period would so reduce-the danger of scaling that mild steel could be used for the gauge. This expectation has been justified. Danger of attack on silica oven walls by the steel gauge body can be eliminated by cementing asbestos paper or an alundum or silica plate to the back of the gauge body. The gauge head itself has a relatively heavy mild-steel body, A, into which standard ¼ in. pipe B is screwed to conduct gas and electrical leads. The body is closed by a single bellows C. consisting of two annuli of 0.011-in. (0.28-mm.) cold-rolled shim-steel spot-welded together at their outside edges. The lower one is

Jan 1, 1944

By W. Hurst, A. F. van Everdingen

A distillate-bearing sand complex is often made up of sand stringers of different permeabilities. In order to take into account the influence of the different permeabilities, "parallel flow" is defined, and this concept is used to compute the recovery efficiency of recycling such a sand complex. In the first approximation the position of the wells with respect to one another is not considered. In order to compute the effect on the recovery efficiency of the position of the wells, the area of a field is considered to be made up of rectangles; each rectangle containing one input well in the center and two producers located symmetrically with respect to the input well. Formulas are given from which to obtain the pressure and streamlines in a steady-state flow. A method is devised to compute rapidly the successive positions of the dry gas front. If the field is irregular in shape, pressure and streamlines can be obtained by a potentio-metric electrical model study. By using the concept of "parallel flow" and the results obtained by mathematical analysis or by electrical model study for a homogeneous formation, the effects of different permeabilities and of the location of the wells can be established. From these studies it is apparent that the efficiency of recycling can be profoundly influenced by differences in permeability among the various parallel strata. Introduction With the discovery of an increasing number of gas-distillate fields in the Gulf Coast, engineers have had occasion to give more thought to the performance of these reservoirs, as evidenced by the literature published in recent years. In the majority of studies published so far the formations are considered to consist of uniform, homogeneous sand. In this paper the authors wish to bring out the effect of variations in the permeability of the formations on the over-all recovery efficiency of wet gas in cycling operations. The importance of the permeability profile is clearly indicated by the fact that in gas cycling, highly permeable stringers in an otherwise tight sand can allow complete displacement of wet by dry gas in these stringers long before the wet gas in the tight portions of the sand is displaced. This by-passing will be reflected by a reduction in the condensate content of the production sooner than can be anticipated from a mathematical analysis or an electrical model study on uniform sands. Electrical model studies or mathematical analyses cannot take into consideration the manifold variations of permeability within the reservoir. Experimental as well as analytical difficulties make it necessary to consider the prototype for either of these studies as a perfectly uniform sand. Mathematical analyses are applicable only when a reservoir can be divided into units of simple geometrical form, of uniform thickness throughout. Electric model studies are capable of giving information on reservoirs of any shape or thickness, but it is essential that the sand be considered homogeneous, so that three-dimensional flow can take place. The method of approach in the following

Jan 1, 1946

By W. Hurst, A. F. van Everdingen

A distillate-bearing sand complex is often made up of sand stringers of different permeabilities. In order to take into account the influence of the different permeabilities, "parallel flow" is defined, and this concept is used to compute the recovery efficiency of recycling such a sand complex. In the first approximation the position of the wells with respect to one another is not considered. In order to compute the effect on the recovery efficiency of the position of the wells, the area of a field is considered to be made up of rectangles; each rectangle containing one input well in the center and two producers located symmetrically with respect to the input well. Formulas are given from which to obtain the pressure and streamlines in a steady-state flow. A method is devised to compute rapidly the successive positions of the dry gas front. If the field is irregular in shape, pressure and streamlines can be obtained by a potentio-metric electrical model study. By using the concept of "parallel flow" and the results obtained by mathematical analysis or by electrical model study for a homogeneous formation, the effects of different permeabilities and of the location of the wells can be established. From these studies it is apparent that the efficiency of recycling can be profoundly influenced by differences in permeability among the various parallel strata. Introduction With the discovery of an increasing number of gas-distillate fields in the Gulf Coast, engineers have had occasion to give more thought to the performance of these reservoirs, as evidenced by the literature published in recent years. In the majority of studies published so far the formations are considered to consist of uniform, homogeneous sand. In this paper the authors wish to bring out the effect of variations in the permeability of the formations on the over-all recovery efficiency of wet gas in cycling operations. The importance of the permeability profile is clearly indicated by the fact that in gas cycling, highly permeable stringers in an otherwise tight sand can allow complete displacement of wet by dry gas in these stringers long before the wet gas in the tight portions of the sand is displaced. This by-passing will be reflected by a reduction in the condensate content of the production sooner than can be anticipated from a mathematical analysis or an electrical model study on uniform sands. Electrical model studies or mathematical analyses cannot take into consideration the manifold variations of permeability within the reservoir. Experimental as well as analytical difficulties make it necessary to consider the prototype for either of these studies as a perfectly uniform sand. Mathematical analyses are applicable only when a reservoir can be divided into units of simple geometrical form, of uniform thickness throughout. Electric model studies are capable of giving information on reservoirs of any shape or thickness, but it is essential that the sand be considered homogeneous, so that three-dimensional flow can take place. The method of approach in the following

Jan 1, 1946

By H. Landsberg

In a previous report1 it was pointed out that a successful attack on roof troubles has to be preceded by extensive scouting. As Lord Kelvin once said, scientific progress can be made only if accurate data are available: "unless you measure, you do not know." The Convergence Recorder For the observation of roof movements in mines the convergence recorder has shown that it will enable us to get some of the necessary information. Results with convergence recorders were first published by Winstanley and other English investigators for rapidly moving longwall faces. In their investigations the speed of work and the heavy overburden produced a considerable amount of absolute values of convergence in a short time. Under the conditions frequently encountered in our investigations in Central Pennsylvania, under shallow, overburden and in mines with slowly proceeding extraction, the movements observed were much less in absolute value, for an equal interval of time. This mas partly because the mines in which our studies were carried on frequently had idle days, sometimes four or five in succession. Therefore continuous records were not employed and a simple convergence gauge was built. In its first models, it consisted only of two telescoping tubes pressed against roof and floor by a coil spring. At the side of the lower tube a rule divided into 1/2-mm. divisions mas fixed and a knife-edge, which was attached to the upper tube, mas slid over the scale in case of convergence between roof and floor. While the larger motions could be read on this device, it seemed to be desirable to increase the accuracy by inserting between the two tubes a dial meter reading in 1/1000 in. Such a gauge was first built in April 1937 and installed for experimental purposes in a bituminous coal mine in Pennsylvania (Fig. I). It was read at least once daily, 24 hr. apart, and if feasible at shorter intervals. After several months of experience it can be said that this type of gauge answers the scientific as well as the practical needs. It is easier to handle than the recorder; no clock is used, there are no pen troubles. The price of

Jan 1, 1938

By H. Landsberg

In a previous report1 it was pointed out that a successful attack on roof troubles has to be preceded by extensive scouting. As Lord Kelvin once said, scientific progress can be made only if accurate data are available: "unless you measure, you do not know." The Convergence Recorder For the observation of roof movements in mines the convergence recorder has shown that it will enable us to get some of the necessary information. Results with convergence recorders were first published by Winstanley and other English investigators for rapidly moving longwall faces. In their investigations the speed of work and the heavy overburden produced a considerable amount of absolute values of convergence in a short time. Under the conditions frequently encountered in our investigations in Central Pennsylvania, under shallow, overburden and in mines with slowly proceeding extraction, the movements observed were much less in absolute value, for an equal interval of time. This mas partly because the mines in which our studies were carried on frequently had idle days, sometimes four or five in succession. Therefore continuous records were not employed and a simple convergence gauge was built. In its first models, it consisted only of two telescoping tubes pressed against roof and floor by a coil spring. At the side of the lower tube a rule divided into 1/2-mm. divisions mas fixed and a knife-edge, which was attached to the upper tube, mas slid over the scale in case of convergence between roof and floor. While the larger motions could be read on this device, it seemed to be desirable to increase the accuracy by inserting between the two tubes a dial meter reading in 1/1000 in. Such a gauge was first built in April 1937 and installed for experimental purposes in a bituminous coal mine in Pennsylvania (Fig. I). It was read at least once daily, 24 hr. apart, and if feasible at shorter intervals. After several months of experience it can be said that this type of gauge answers the scientific as well as the practical needs. It is easier to handle than the recorder; no clock is used, there are no pen troubles. The price of

Jan 1, 1938

By A. T. Aldred, K. M. Myles

The vapor pressure of chromium over solid V-Cr alloys has been measured by the torsion-effusion method in the temperature range 1450" to 1650°K. The chemical activities as well as the free energies, entropies, and enthalpies of formation of the alloys have hem computed from the vapor-pressure data. The activities of both chromium and vanadium exhibit fairly small negative deviations from Raoult's law over the entire composition range. The values of the excess entropies and the enthalpies of formation found at 1550°K are considered in terms of the changes in the clzaracteristic properties of vanadium and chromium that occur upon alloying. RECENT interest in the theory and properties of transition-metal alloys has shown the need for relevant thermodynamic data. The present investigation of the V-Cr system was undertaken as part of a more general study of thermodynamic properties of transition-metal alloys. The system was chosen because of the reported complete solid solubility of the components at all temperatures1 and because the difference in magnitude of the vapor pressures of vanadium and chromium allowed a simple effusion technique to be used. The torsion-effusion method was employed to minimize compositional changes in the alloys during the experiments. EXPERIMENTAL Equipment. The torsion-effusion apparatus, shown diagrammatic ally in Fig. 1, consists of a torsion system suspended inside a vertical vacuum chamber whose lower end is surrounded by a high-temperature vacuum furnace. An auxiliary optical lever and screen are used to determine the angle of rotation of the effusion cell. The torsion fiber is an annealed, high-purity, tungsten wire usually between 0.003 and 0.007 cm in diameter and about 43 cm long. The wire supports a concave mirror and a rigid tantalum connector tube. The effusion cell is fastened to the lower end of the connector tube by a dovetailed yoke and har- ness arrangement. The cells, which are 1.27 cm in diameter and 4.4 cm long, were made by electron-beam welding tantalum endcaps onto a 0.025-cm-wall tantalum tube. The two orifices, formed by drilling, have similar areas ranging from 0.011 to 0.031 sq cm. The noninductive sheath-type furnace consists of a single-phase tantalum heating element 6.35 cm in diameter, 15 cm high, and 0.013 cm thick; the element is completely surrounded by radiation shields in an evacuated chamber. The power system includes a 17-kva self-saturating saturable core reactor with an integral magnetic amplifier and a water-cooled, 15-kva, step-down power transformer with a multitap secondary. Temperatures are controlled to within ±1/2o at 1600°K by means of a unit that includes a reference voltage source, a dc electronic null detector, a current-adjusting proportional band relay, and the self - saturating reactor. At 1650°K the temperature variation within the cell, vertically and horizontally, is 3/4oK. Unwanted motions of the torsion system are damped by the movement of an aluminum vane, which is mounted on the connector tube, between the poles of an electromagnet. When not in use the magnet is withdrawn and rotated 90 deg to prevent its interaction with the rotation of the system. Measurements. The vapor pressure, p, is re-

Jan 1, 1964

By Foster Fraas

MOST commercial electrostatic separators utilize the electrical property of conductivity, but although based on the same principles, they are constructed in a variety of forms, a common one being the simple roll type. Some information obtained during an investigation of that type of separator, and which indirectly is applicable to other types, is presented here. NUMERICAL RELATIONSHIP In Fig. I material discharged from hopper 6 is fed onto grounded rotating roll 2. Electrode 3 is at a high electrical potential with respect to roll 2, and any conductive particle in contact with roll 2 therefore acquires an electrical charge of such polarity that, when present in the electrical field, the force on it is in the direction of electrode 3. A detailed description of the charging by conductance as utilized in electrostatic separators may be found in a previous publication.1 As a result of this force, the path of the projected particle is changed in increasing amounts in the direction toward region C as the magnitude of the charge is increased. With the dividing edge 4 the projected particles may be divided into two fractions -those in region C designated as "deflected" or " deflectant " and those in region B designated as "residue." [ ] When material is passed over the roll only once, a complete separation is seldom obtained, therefore most commercial separators contain several roll-separator units in series, and some practical machines use as many as 12. In this paper a "pass" means the passage of material over a single-roll unit. The procedure is to repass either residue B with a low potential on electrode 3 or deflectant C with a high potential on 3. Most electrostatic separations follow a flowsheet of roughing and cleaning either the concentrate or the tailing, on both. In a specific instance, a dry, heated mixture of wet cleaned chromite and garnet from an

Jan 1, 1942

By Alan Morris

THE investigation of the hot-working properties of metals and alloys furnishes a problem which has been attacked in many ways. Tensile, impact and hardness tests on heated specimens have furnished interesting data, but in most cases either the tests are difficult to make or the results hard to translate into terms of practical value. Some investigators have used the drop hammer to advantage. It furnishes a rapid and simple method of comparing the plasticity of metals at elevated temperatures. The indications obtained by its use are of value only in so far as their significance is understood and they can be intelligently used to predict the behavior of a given metal under given hot-working conditions. The work reported here was undertaken not only to add-something to the existing volume of such data but also to contribute to our understanding of the results. Doerinckel and Trockels1 used cylindrical specimens and determined the work required to reduce the specimen to one-half the original height. Ellis2 studied the effect of constitution on the malleability of steel at high temperature. His method and that of Kent3 were similar to the one used in the present work. The tests described by Kent were made on samples of tin, zinc, aluminum, copper, lead, 70:30 and 60:40 brasses, with and without a small quantity of lead. He concluded that the test would "indicate whether a material can be forged at a given temperature without cracking." This interpretation must be used with caution. While it is probably true within limits, one must consider the severity of the forging operation. Again, it will not apply strictly to forms of hot working other than forging. For instance, an alloy running 61.0 per cent. copper, 3.25 per cent. lead, remainder zinc, will crack badly in the test, yet it is extruded commercially. When the possibility of hot-working a new alloy is being considered a study of its drop-hammer test should help

Jan 1, 1931

By W. F. Boericke

THE recent completion by the United States Aluminum Company of a $4,000,000 addition to its plant at Massena, N. Y., consisting of a large blooming mill and structural mill, gives this organization, a subsidiary of the Aluminum Company of America, the distinction of possessing the largest aluminum rolling mill in the world, as well as the first mil1 in this country to roll aluminum exclusively. The plant is located near the international boundary line between Canada and the United States, about 3 miles from the St. Lawrence River, to take advantage of the development of cheap hydroelectric power which is needed not only for the manufacture of structural shapes from the ingots, but in the reduction of alumina to the metal by the well-known Hall process as well. A power canal from the St. Lawrence River to the power house on the Grasse River at the plant provides for the waterflow, which, coupled with a drop of 47 ft. in 2% miles, generates 80,000 hp. through vertical turbines. An additional 60,000 hp. is purchased.

Jan 1, 1930