Search Documents

By Franz Posepny

CONTENTS. Introduction. Part I. General Facts And Theories. [ ]

Jan 1, 1902

By D. K. Bose, C. K. Gupta, K. U. Nair

A new approach to processing an indigenously available low made molysulfide concentrate by chlorination with elemental chlorine in presence of oxygen is reported. Recovery of nickel and copper values associated with the sulfide concentrate by suitably treating the residue obtained after chlorination is also reported.

Jan 3, 1978

By J. A. Hren, G. Thomas

A high-temperature stage has been used to study precipitation and dissolution in thin foils of Al-20pct Ag alloy directly in the electron microscope. The results show that the aging characteristics are similar to those observed for bulk materials, and in addition, direct evidence is presented for clustering at the solid solution temperature. The limit of solubility of G. P. zones is-350°C. The heterogeneous precipitation, the growth and dissolution of ?&apos;have been studied in detail. Growth of ?&apos; parallel to the basal planes, occurs by continuous motion of inter -facial partial dislocations. Growth stops at intersecting particles due to formation of sessile a/6 <110> interfacial dislocations. Growth normal to the habit plane occurs by the spontaneous nucleation of partial dislocations on alternate (111) planes and the thickening rate is --10-3= times the lengthening rate. The precipitates dissolve in layers and the final product is a whole a/2 <110> dislocation . The nucleation -growth -dissolution processes are thus completely reversible. Kinetic data obtained from the dissolution rates of ?&apos;particles enable the diffusion coefficient to be determined and the activation energy is found to be 37.5(±4) kcal mol-1, which is that expected for dzffusion of silver in aluminum. The velocity of the interfacial dislocations is thus dependent solely on the rate of diffusion of silver atoms. RECENTLY it was demonstrated that a high-temperature stage could be effectively used in the electron microscope to follow directly the processes of precipitation and dissolution in thin foils of A1-4 pct Cu alloy.&apos; These experiments also provided kinetic data which enabled the diffusion coefficient to be estimated. This new development of electron metallography opens up many fruitful areas of research and it was decided to investigate the aging behavior in thin foils of A1-20 pct Ag alloy, particularly the mechanism of heterogeneous precipitation (i.e., precipitation on lattice defects). This system was chosen because the aging characteristics of bulk specimens are now well known,2"7 and because we wished to obtain more details of the role played by partial dislocations and stacking faults in the nucleation growth and dissolution of the hcp ?&apos; phase. This is of interest for the general case of fcc-- hcp transformations. Part of the A1-Ag phase diagram is shown in Fig. 1. The use of a high-temperature stage also enables a study to be made of the clustering process (formation of G. P. zones) and to determine the structure of the solid solution prior to the usual quenching and aging procedures. It is also possible to obtain kinetic data from measurements of the rates of dissolution of precipitate particles. Unlike the results of previous experiments on A1-4 pct CU 1 where much of the initial precipitation occurred on the foil surfaces, the results on the A1-20 pct A1 alloy were identical to those reported for bulk specimens6,7 and no surface precipitation was ever observed. Thus, it was possible to follow the aging sequence: G.P. zones — ?&apos; — ? directly in the thin foils. This paper is concerned with the formation and dissolution of zones and the ?&apos; phase, and no attempt has been made so far to follow the mode of discontinuous precipitation of ?. I) EXPERIMENTAL DETAILS The high-purity A1-20 pct Ag alloy was prepared by the Aluminum Co. of America in the form of 0.001-in.-thick sheets. These were cold rolled with intermediate anneals to a thickness of 0.0004 in.,

Jan 1, 1963

C. N. FEnner, New York City (communication to the Secretary) : A possible explanation of some of the&apos; phenomena of amalgamation cited by Mr. Bayliss and others has occurred to me. We know that if, to a quantity of mercury, gold and silver are added until a putty-like paste is formed, and if this mass is spread on a flat surface and pressure is applied, a more fluid portion of the mercury will be squeezed out from the rest, carrying gold and silver with it. The proportion of gold to silver will depend, I think, upon various causes and conditions—the relative chemical affinity which gold and silver have for mercury; the amount of pressure used; the presence of other metals:

Jan 1, 1898

By J. L. Wyatt

THE smelting of ilmenite to produce a slag rich in titanium, with pig-iron as a byproduct, introduces new concepts in electric smelting metallurgy. Titanium slags are characterized by low electrical resistance, thereby requiring a different type of electric furnace operation, and power supply sources substantially different from those encountered in normal steel melting and siliceous ore smelting furnaces. This paper describes special apparatus for determining specific electrical resistivity of titanium slags, and reports the values obtained on slags encountered in the process of smelting ilmenite ores. In an induction furnace under conditions approximating normal furnacing operation, 25 general heats and 6 special standardization and comparison heats were run. Results indicate relatively low resistivity. Resistivity depends primarily on slag composition, and, to a lesser degree, on temperature. During the summer of 1947 a cooperative project between the National Lead Co. and the Bureau of Mines was conducted at Boulder City, Nevada, in the Electrometallurgical Laboratories of the Bureau. The project involved smelting of ilmenite ores in electric furnaces, and has been reported in detail.&apos; The author participated as a member of the staff of the National Lead Co. during the entire campaign. One outstanding characteristic of the titaniferous slags, their apparently excellent and variable electrical conductivity, was considered sufficiently important to warrant further study. Although little electric smelting of iron ores has been done in the United States, a certain amount of information is available for comparative purposes. Personal experience in smelting siliceous iron ores in electric furnaces furnished further information for comparison. In general, silicate slags are relatively poor conductors of electricity. Current flow during smelting operations may be maintained through a floating layer of coke on top of the slag bath, or through a bath of molten iron, beneath the slag. Silicate slags are not sufficiently conductive to furnish a path for current passage when normal furnace voltages are used. Experimental smelting of a silicate iron ore was undertaken for comparative purposes. A fluid melt was not obtained until the FeO content was reduced to 15 pct. The resistivity increased as the FeO content decreased, FeO compounds being the most conductive of the various oxides in such a normal slag system. The converse appears to be true in slags containing large percentages of TiO2. It has been found that titanium slags become molten with FeO percentages in excess of 30 pct, and that the conductivity becomes generally better as the FeO con-tent of the slag diminishes. This phenomenon was demonstrated in the furnacing operations at Boulder City. During the initial smelting period furnace electrodes could be held immersed several inches in the slag, with tap selectors set for a no-load voltage of 70 v. As the FeO content decreased, the furnace electrodes would "walk up," until at one point in the process the tips would break the surface and arc on top of the slag. This was undesirable since direct arcing caused losses of important flux additions. The slag compositions under study at that time were such that losses due to surface arcing sometimes caused viscous slags to be formed. Forcing the electrodes into the slag bath by manual control to prevent surface arcing resulted in excessive power input and lack of control. Suitable low voltages were not available. Measurement of the electrical resistivity of titanium slags at various operating temperatures and slag compositions was undertaken. It was believed that this information would be of use in the design of electric furnaces suitable for smelting ilmenite, with voltages, electrode sizes, and electrode spacing adapted specifically to titanium slags.

Jan 1, 1951

By Peter F. Weiss

INTRODUCTION Austro-American Magnesite Co. of Radenthein, Carinthia, Austria, is a wholly owned subsidiary of General Refractories Company, Bala Cynwyd, USA, and has been incorporated since 1908. The raw material basis is the magnesite mine on Millstatt Alp, located in the mountains near Radenthein at an altitude of 1500 m above sea level. The mined crude magnesite is crushed in a surface crushing plant to minus 35 mm and consequently hauled to the processing plant in the valley by means of a cable conveyor of 7.5 km length. The annual production of 350,000 mt is accomplished with 20 supervisors and 122 workers (of those 60 are in the mine). The labor requirement for block caving is 0.2 man hr/mt, corresponding to an output of 40 mt/man/ shift. GEOLOGY The rock in this area mainly consists of crystalline type schist. There are mostly coarse crystalline garnet mica schists with varying mineral concentrations, and to a lesser degree, some deposits of amphibolite and marble. This petrographically rather homogeneous rock is divided into numerous different tectonic units (covers and scales). The magnesite deposit itself is a foreign body that also has been tectonically inserted. The ore body has a length of 600 m, is 450 m deep, and has a thickness of 60 m on average, varying substantially however, The contact with the accessory rock is very precise. The deposit 1 = ore body, 2 = previous open pit, 3 = caved in area, 4 = block under excavation, 5 = land slide consists of coarse crystalline magnesite in excess of 90 per cent. The few impurities consist of dolomite and talc. The lower part of the deposit is inclined parallel with the schists at approx. 40 degrees. In profile it can be seen, however, that the upper part of the deposit has been tilted over. This is a result of a post-glacial land slide reaching from the bottom of the valley at 1400 m above sea level to the peak of the mountain at 2100 m above sea level. Due to this land slide, with horizontal movements of up to 100 meters, as well as older tectonic events, the rock was crushed to a vast extent. Through mining, the land slide was reactivated; about 40 million cubic meters of rock slowly flow downhill almost like a plasticized mass. Near the surface, the rock is completely crushed and resembles a glacier rupture zone. This renders the originally impermeable rock completely water permeable so that practically all of the annual quantity of 1000 to 1100 mm of precipitation permeates the rock and flows down into the mine. The carbonate rock turns into the preferred aquifer. From 1700 to 2600 cubic meters of water have to be pumped from the mine daily. On one hand, additional problems are caused by the water in the mine, on the other hand we have learned to make use of the down- hill pressure forces to improve the crushing process during block caving. The boundary of the downhill shearing zone moves downward as mining goes deeper.

Jan 1, 1981

By H. F. Johnson, C. S. Harloff

The Nichols series system of electrolytic copper refining has successfully maintained its strong competitive position in the copper-refining industry of today; therefore the improvements made in accomplishing this result are of interest. While additional interest would lie in specific comparisons of results obtained in series operation with those in multiple, we have refrained from such a comparison because it can be fair to both only when they are operating under similar conditions on the same grade of materials. Historical The Nichols Copper Co. started a small refinery at Laurel Hill, using its present system, about 1892. The details of the process in its early stage of development were kept strictly secret, so that no information was published or interchange of ideas permitted with the staffs of other copper refineries, where the multiple system was being developed at the same time. However, the fundamentals of the process and type of cell used today differ very little from their earliest form. All operations including loading and unloading of tanks, and all transportation as well, were carried on by hand. The plant remained in this condition with a gradual expansion taking place until the World War forced such a rapid development that little time or thought could be devoted to modernization or mechanical improvement requiring careful design or detailed planning. Considerable progress was made, however. (1) Large refining furnaces were developed. (2) The old expensive air-lift type of circulation was abandoned in favor of the present system. (3) Operating technique was gradually developed to a high point of efficiency. (4) Tank construction and lining were greatly improved, the first concrete tank being installed in 1915. (This tank is still in operating condition.) (5) A new power plant was constructed. (6) Fuel oil was substituted for lump coal on the refining furnaces. (7) Mechanical casting of the finished product was accomplished. During this entire period the plant was particularly fortunate in receiving only high-grade, clean copper bullion coming principally from the Phelps Dodge mines in Arizona. This, together with the lack of

Jan 1, 1934

Admissions: Joseph C. Gordon, Chairman K. F. Anderson Allen B. Gibson H. J. Gruy R. F. Madera Dan H.-McLendon K. W. Robbins Aurel E. Smith W. F. West Advertising: John. D. Wisenbaker, Chairman Bernard F. Klein Henry N. Lyle R. E. Howard Clark R. Edgecomb, Jr. [ ]

Jan 1, 1961

By Robert D. Pehlke, Arden L. Bement

A mass transfer coefficient for the removal of hydrogen from liquid aluminum by inert flush degassing has been determined experimentally at 700°C. A mathematical model has been derived, assuming transport control, which adequately describes the experimental data. The removal of hydrogen is shown to increase with decreasing bubble size, and with increasing flow of flushing gas. The presence of hydrogen in liquid metals in amounts which exceed the solid solubility at one atmosphere hydrogen pressure is highly undesirable, causing unsound ingots or castings, or resulting in difficulties during further fabrication. The removal of hydrogen from liquid metals can be accomplished by several methods, the principal two being vacuum treating and inert flush degassing. The design of a process involving either of these techniques is based on the mass transfer coefficient for hydrogen between the liquid metal and a hydrogen-dilute gas phase. In an effort to extend our knowledge in this area, an investigation of the rate of removal of hydrogen from liquid metals by inert gas flushing was undertaken. In view of the difficulties encountered with gas porosity in the casting of aluminum and aluminum alloys, and because of certain experimental advantages, liquid aluminum was selected for the study. PREVIOUS INVESTIGATIONS The removal of gases from liquid metals, particularly steel, has received considerable attention in recent years, The first definitive work of a theoretical nature was presented by Geller1 who considered the case where equilibrium exists between purging gases and metal bath during flushing, and also deviations from this ideal case. Hulme2 has surveyed a number of experimental studies and discussed some of the practical limitations of removing dissolved gases from molten metals. More recently a number of studies have been reported on degassing of steel melts by flushing with an inert gas.3&apos;4 Considerable work has also been reported on aqueous and organic liquid-gas systems, and an excellent summary prepared by Hovis.5 The treatment of liquid aluminum by a flushing gas to remove dissolved hydrogen has been known for several decades.6 A number of gases have been used for this purpose, including nitrogen, argon, and chlorine, or mixtures of these gases. Tikkanen and Erkko7 have studied the relative density changes of aluminum castings poured from melts degassed with chlorine, nitrogen, and mixtures of the two gases. Their

Jan 1, 1962

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members) Members and guests who called at Institute headquarters during the period Feb. 10, 1917 to Mar. 10, 1917: F. H. Armstrong, Vulcan, Mich. G. Komar, Staten Island, N. Y. Franklin Bache, Philadelphia, Pa. H. M. LaFollette, LaFollette, Tenn. R. A. Bingham, W. Orange, N. J. H. Mortimer-Lamb, Montreal, Canada. G. S. Blair, Pittsburgh, Pa. J. S. Lane, New York, N. Y. Graham Bright, Pittsburgh, Pa. D. H. McLaughlin, Cambridge, Mass. C. A. Burdick, New York, N. Y. F. J. McMahon, Wilkes-Barre, Pa. Frederick P. Burrall, Dawson, Y. T. F. Oskar Martin, San Francisco, Cal. William Campbell, New York, N. Y. C. Mentzel, New York, N. Y. G. L. Carlisle, Jr., New York, N. Y. T. C. Merriman, New Haven, Conn. J. Murray Clark, Toronto, Canada. K. -A. Pauly, Schenectady, N. Y. Wayne Darlington, Philadelphia, Pa. , Francis R. Pyne, Elizabeth, N. J. Ralph W. Deacon, Elizabeth, N. J. C. S. Robinson, Youngstown, O. P. St. Jon Dixon; So. Porcupine, Canada. W. A. Scheuch, New York, N. Y. A. E. Drucker, New York, N. Y. Jesse Scobey, New York, N. Y. Lucien Eaton, Ishpeming, Mich. Dunbar D. Scott, Rochester, N. Y. W. E. Goldsborough, New York, N. Y. W. C. Smith, Elizabeth, N. J. C. Marshall Gravatt, Port Royal, Va. Charles Spearman, Mt. St. Patrick, Can. C. N. Hickok, Cleveland, O. . - Harold C: E. Spence, Duncan, Ariz. C. Vey Holman, Rockland, Me. M. M. Thompson, Morsemere, N. J. W. F. Jahn, Kirkland Lake, Canada. Benjamin F. Tibby, Salt Lake City, Utah. F. E. Johnesse, Boise, Ida. J. S. Unger, Pittsburgh, Pa. E. C. Johnson, Chicago, Ill.

Jan 4, 1917

By David A. Thomas, John F. Peck

Fibrous microstructures and their development have been studied by metallography and by hardness and quantitative metallographic measurements. Thin, curved grains were observed in transverse sections of commercial tungsten wire and were developed in laboratory-drawn iron wire at reductions greater than about 70 pct. The unusual grain shapes are attributed to the nonuniform mode of deformation of the grains associated with the characteristic [I101 preferred orientation that develops in bcc metals during drawing. Transverse sections of heavily swaged iron wire showed a ospiral nebulao structure that appears to result from the elliptical shape of the cross section of the swaging dies and their rotary motion. Hardness and quantitative metallographic results show unusual trends that parallel the changes in microstructure. Other phenomena are considwed in light of the results, including the strength of fine wires of bcc metals, ocylindricalo textures, and the ductility of fibrous tungsten. 1 HE microstructure of tungsten wire in a longitudinal section shows grains highly elongated in the working direction, giving the appearance of a bundle of parallel fibers, Fig. l(a). Wires of tungsten and other bcc metals show a pronounced preferred orientation in which a [I101 direction is parallel to the wire axis.l The microstructure and texture of tungsten develop during warm working (working above room temperature but below the recrystallization temperature) into wire by swaging and drawing. Fibrous tungsten so produced has limited but useful room-temperature ductility, whereas annealed tungsten is brittle at room temperature. During an investigation of the effect of recovery annealing on the substructure of commerical 0.030 in. diam tungsten wire, it was found that transverse sections of the as-received material showed thin, curved grains, Fig. 1(b), instead of the expected equiaxed grains. The fact that Figs. l(a) and (b) show different sections of the same material at the same magnification is at first disconcerting, because the long dimension of the curved grains in the transverse section is several times the average fiber width in the longitudinal section. However, a longitudinal section cuts most of the curved grains across their narrow dimension, giving the appearance of a multitude of narrow fibers. On the other hand, the plane of a longitudinal section occasionally includes a long dimension of a curved grain, resulting in a broad ofibero, such as A in Fig. l(a). EXPERIMENTS AND RESULTS To investigate the origin of fibrous microstructures and particularly the unusual transverse-section structure of tungsten, rods of iron (also bcc) were drawn and swaged in the laboratory. One rod of annealed Ferrovac E was drawn in six steps to a total reduction in area of 87 pct (0.10 to 0.036 in. diam), and a second rod was swaged to the same reduction, using approximately the same reduction steps. Longitudinal and transverse sections of the swaged and drawn iron wires are shown in Fig. 2, for reductions in area of 39, 73, and 87 pct. A fibrous microstructure in longitudinal section is first evident at 73 pct reduction, and it is further developed at 87 pct reduction. The grains in transverse section remain equiaxed until about 73 pct reduction, when they become somewhat elongated and curved. At 87 pct reduction, the drawn wire shows thin, curved grains in the transverse section, similar to those observed in tungsten. The transverse sections of the iron wires swaged 83 and 87 pct reduction in area show the striking ospiral nebulao structure in Fig. 2(d). This struc-

Jan 1, 1962

By Forbes Rickard

Gilpin County, the cradle of mining in Colorado and the Cornwall of North America, is too well known to need much introduction; get, for the benefit of those not familiar with the district, it may be well to premise that it comprises a tract of country of about 122 square miles, lying between the counties of Jefferson, Boulder and Clear Creek, and hounded on the west by the main range of the Colorado Rockies. It is located centrally in the State, 40 miles west from the city of Denver. During the 38 years since the first gold-discovery, Gilpin county has contributed about eighty million dollars in gold and silver to the world&apos;s supply of these metals. Many mining districts have had their rise and decline in half this time; but, very far from being exhausted, this mining district is still in the ascendant; its output is increasing (it was $3,600,000 for the year just closed), and it was never more prosperous nor productive than to-day. Taken generally, there does not exist anywhere in the world so great a number of permanent veins within so small an area as in this district. Gilpin is practically a " poor man&apos;s camp." Its veins, with few exceptions, outcrop at the surface. In the oarlier---days of the camp these outcrops were worked in many instances by sluice-mining; particularly is this the case with regard to the veins of the Russell gulch. Discoveries are still made in the heart of this district, and the productive area is every year extending its limits. The districts of Yankee Hill, Hawkeye and Pine Creek, which used to be isolated, are now part and portion of the one gold-field of Gilpin county. Within the last year sensationally rich gold-discoveries have

Jan 1, 1899

By D. A. Augenstein, L. V. Amundson

Operators of coal preparation plants use equipment such as large-capacity dump trucks and bulldozers to haul, spread, and compact refuse material to conform to federal and state regulations governing the disposal of solid waste. For example, federal regulations require that refuse be spread and compacted in layers not more than 0.6 m (2 ft) thick. If the refuse layers or piles have poor load-bearing characteristics, movement of equipment over them becomes extremely difficult. The increasing cost and limited space for the construction of settling ponds extensively used for fine refuse disposal are leading to the growing practice of dewatering the fine refuse by means of vacuum disk filters and combining the resulting filter cake with coarse refuse for waste bank disposal. However, this filter cake usually contains more than 25% moisture. Therefore, when it is combined with coarse refuse, the moisture level of the total refuse may become high enough to impair the load-bearing strength of the refuse. Precisely this problem and the attendant difficulties of moving heavy equipment arose when vacuum disk filters were installed at a preparation plant in West Virginia. Combining the moist filter cake with the coarse refuse generally results in a 12% moisture level for the total refuse at this plant. At this moisture level, the refuse can still be handled with some dif¬ficulty by the equipment. However, the problem has frequently been compounded after rains. The experimental program described in this paper tested the following methods of improving the load-bearing properties of coal refuse: moisture reduction, addition of crushed coarse refuse, addition of fly ash, addition of lime, and addition of a mixture of lime and fly ash. In terms of a balance between economic and technical considerations, the most effective method was demonstrated by laboratory and plant tests to be a 2% to 5% addition of lime. Test Program During formulation of a test program aimed at improving coal refuse stability, a number of treatment techniques were selected for evaluation of their effect on refuse load-bearing characteristics. The reduction of refuse moisture was the first technique considered, since moisture content plays a key role in the bearing strength of a bulk solid. The reasoning was that a very small reduction in refuse moisture, provided it could be accomplished with minimal effort and cost, would be sufficient for eliminating refuse disposal problems most of the time. At the same time, it was recognized that periods of rainy weather would offset moisture-reduction measures. Other techniques selected for evaluation because of their potential for improving refuse-bearing strength at reasonable cost were: addition of crushed coarse refuse, the addition of fly ash, and the addition of lime. A simple one-dimensional laboratory compaction test was designed for evaluating the effect of each of these techniques on refuse-bearing strength. Those techniques that gave best results in the laboratory would then be tested in the preparation plant in West Virginia. Laboratory Tests The laboratory test for evaluating each of the techniques involved the application of weight to a load module placed on a refuse sample in a container. The distance the load module sank with an increasing amount of applied weight was measured, and the relationship between module displacement and loading was obtained. The refuse container was large enough to minimize the influence of wall effects, and to decrease the effect of the container bottom, a test was terminated when the load module sank to about three fourths the depth of the container. Initially, an attempt was made to conduct compaction experiments with samples of total plant refuse. However, the presence of + 0.13 m (+ 5 in.) material in the refuse interfered with the mechanics of the test, and the large amount of material required for a representative sample made testing extremely tedious and time-consuming. To avoid this problem and because it was believed that only the fine components of the refuse were the major cause of the stability problem, tests were conducted with 13 mm X 0 (1/2 in. X 0) material from the total plant refuse. The equipment consisted of a 0.46 m (18 in.) cubic container, a loading module with 62 cm2 loading area, weights totaling 450 kg, and a portable concrete mixer for combining water and additives with the refuse. Refuse samples of about 110 kg dry weight were used for each test. Experimental compaction test data were evaluated by plotting the linear displacement of the load module vs. loading. During compaction tests, the vertical displacement of the load module was measured at each loading value. The plot of

Jan 1, 1980

By I. J. Hegyi, J. J. Tietjen, H. Nelson, J. I. Pankove

The fabrication of p-n junctions in GaAsl-,P, alloys by a vapor-phase gowth technique has for the first tirne resulted in room-temperature injection lasers capable of operating over a broad range of wavelengths extending into the visible region of the spectrum. The shortest wavelength achieved to date is 6750A at room tetnperature. In addition, at 78°K the threshold current density values for these lasers are generally the lo~vest reported, and the emitted radiation extends to the lozc,est wavelength ever attained (6350A). With lasers fabricated from material containing 14 pct Gap, quanticm efficiencies of 26 pct and peak power outputs of 25 zu were obtained at room temperature. ALTHOUGH room-temperature operation of GaAs injection lasers has been well-documented,&apos;-5 the operation of GaAsl-,P, (x > 0) laser diodes has been restricted to relatively low temperatures.8-&apos;0 This has been previously attributed5, 7, 10-12 partially to the difficulty of preparing single-crystalline GaAsl-& alloys having a high degree of chemical homogeneity and purity. Also, with these materials it has been difficult to prepare high-quality, abrupt p-12 junctions by diffusion techniques; and, in turn, this has made it difficult to obtain optimum electrical properties for room-temperature operationL3 in the resulting laser diodes. As a result, GaAsl-,P, laser diodes have not been efficient enough to permit operation at room temperature. For example, using diffused structures, only a few diodes were obtained which could be operated even close to room temperature (255K)." Recently, a vapor-phase growth method of preparing epitaxial deposits of GaAsl - .P, alloys has been described,14 and the high-purity and homogeneity of these materials has been previously demonstrated. Of special significance, with this technique, n- or p -type doping can be initiated or discontinued at any time and at almost any rate during the crystal growth so that the donor and the acceptor concentrations can be easily controlled to obtain desired impurity profiles. This permits high-quality, abrupt p-TZ junctions to be vapor-phase grown entirely during the crystal growth process, so that diffusion or other p-n junction fabrication processes are unnecessary. After growth, the device does not have to be heated to elevated temperatures, which avoids the possible unwanted introduction and motion of both impurities and lattice defects. Using the vapor-phase growth method cited above, over 300 room-temperature injection lasers have been prepared from GaAsl-,P, alloys having compositions in the range of 0 5 x 5 0.41. These lasers have emitted cohe~ent radiation in the spectral range of 8350 to 6350A at 78°K or from 9000 to 6750A at room temperature. The threshold current densities of the best lasers are independent of the alloy composition over the range 0 < x < 0.2 and compare favorably with values for good GaAs lasers.&apos; MATERIAL PREPARATION Multilayer, epitaxial deposits of GaAsl-,P, alloys are prepared by a vapor-growth technique described elsewhere.14 With this technique, the individual layers which comprise the multilayer structure are prepared sequentially in the deposition apparatus without interrupting the crystal growth. The epitaxial layers are deposited on GaAs substrate surfaces oriented normal to the ( 100) direction. The substrate wafers employed in this study were usually doped with tellurium to an electron concentration of approximately 2 x 10" per cu cm. To avoid strains, the first 10 to 15 p of the deposited material is uniformly graded from pure GaAs to the specific GaAsl- ,P, alloy composition of interest. The GaAsl - ,P, alloy growth is then continued to form a layer of constant composition having a thickness in the range of 25 to 75 p. Both the graded region and the layer of constant composition are doped with selenium to an electron concentration of about 2 x 10" per cu cm. The p region of the diode is then incorporated in the crystal by abruptly changing the dopant concentrations in the vapor phase to facilitate doping with zinc. This layer has a hole concentration of approximately 3 X 1019 per cu cm and typically is 50 p thick. DEVICE FABRICATION In general, the GaAs substrate and the region of graded composition are removed. Ohmic contacts are made to the n-type side by tin evaporation and to the p-type side by an electrodeless nickel deposition. This is followed by an electrodeless deposition of gold on both sides. The crystal wafer is then cleaved along (110) planes and sawed into rectangular parallelepipeds. Typical dimensions are 100 by 300 for the junction area and 100 µ for the diode height. The diodes are either soldered to a copper stud or pressure-mounted in a copper clip. RESULTS AND DISCUSSION Approximately 400 laser diodes having compositions in the range of 0.41 have been prepared by the method described above. Each laser was routinely tested at liquid-nitrogen temperature. The lasers were operated with l-psec current pulses at a repetition rate of 60 pulses per sec. The parameters of greatest practical interest are the photon energy or wavelength of the laser output and the threshold current density. Fig. 1 shows the variation of photon energy with alloy composition at 78°K. The composition was determined from the lattice constant of the material obtained by X-ray back-reflection measurements. Although there

Jan 1, 1968

By D. M. McFarland

A FEW years ago a novel electric detonator known as the split-second or millisecond delay electric blasting cap was introduced for use in quarry blasting. Regular electric blasting caps fired in series may be depended upon to fire within a millisecond or so from the first to the last in a series. Regular delay electric blasting caps are provided that fire one period after the other period in intervals of 1/2 to possibly 1 1/2 sec. Most split-second or millisecond delays are designed to fire one period after the other period in possibly 25 to 50 millisecond intervals. The ear is not capable of detecting time intervals of this magnitude. The primary thought at the time millisecond de- lays were introduced was to investigate the results on rock breakage by firing a line of holes in a quarry face.so that charges in adjacent holes would not be detonated simultaneously. This could not be accomplished satisfactorily with regular delays. The time interval between successive periods of $5 to 1 sec was sufficient to permit considerable movement of the burden. If the burden of one hole was reduced to a great extent by the firing of an adjacent hole, the firing of the hole with the reduced burden would likely reveal this lack of confinement by a terrific report and wild throw of rock.

Jan 1, 1950

Meeting of April 24, 1914.-President Thayer announced the appointment of the Committee on Safety and Sanitation. The Committee on Nominations for officers for 1915 was appointed, as follows: William J. Cox, Chairman; H. Poster Bain, Joseph Daniels, Charles E. Mills, R. V. Norris, E. Gybbon Spilsbury, and Herbert A. Wheeler. The request of twenty residents of Salt Lake City and vicinity for permission to establish the Utah-Nevada Local Section was granted and R. C. Gemmell was appointed Chairman of the Committee on Organization. The following resolution was adopted: Resolved: That under authority of Article V, Section 7, of the Constitution, a special Committee be and hereby is appointed, to consist of the President and six other members of the Institute, to be named by him, Who shall be authorized to appear before the proper authorities at Washington and urge that Mining Engineers be appointed upon the proposed Commission for revision of the Federal Mining Laws. Further Resolved: That the activities of this special Committee be restricted to the authority given in this resolution.

Jan 6, 1914

Adams . Bernard . Student. South Dakota School of Mines .Rapid City . S . D . Ahlskog . Harold A. Student. Washington State College Pullman. Wash . Aldridge. John. Student. New Mexico School of Mines Socorro. N . M . Almstrom . Adne A .. Student. Met . Engrs.. Washington State College ..... .Pullman. Wash . Ancell . Virgil F.. Student. Missouri School of Mines Rolla. Mo . AnkudinoE. N., Mill Draftsman. Arthur G . McKee & Ch., 2422 Euclid Ave., Cleveland. Ohio . Avablaea . Salvador C.. Student. Univ. of California Los Angeles. Cal. Armstrong. Robert E .. Student. Lafayette College .Easton. P a Armstrong . Thomas E.. Student. Univ . of California Los Angela. Cal Aud. Robert A .. Student. Lafayette College Easton. Pa .

Jan 1, 1929

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman. PERCY E. BARBOUR, Vice-Chairman. A. D. BEERS. Secretary, 55 Wall St., New York. N. Y. C. A. BOHN, Treasurer. Boston Meets first Monday of each winter month. C. C. EUSTIS, Chairman. R. L. AGASSIZ, Vice-Chairman. E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology, Boston, Mass. ALBERT SAUVEUR, H. L. SMYTH. Columbia Holds four sessions during year. Annual meeting in September or October. STANLY A. EASTON, Chairman. FREDERIC KEFFER, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2164, Spokane, Wash. C. LIVINGSTON. FRANK A. ROSS.

Jan 6, 1916

By GEORGE W. HARHIS

IN the earlier period of anthracite-ruining, much coal was wasted, both underground and in the culm-banks on the surface. Such waste is common in the development of new mining districts, in which, as a rule, only the richest material can be profitably treated. In the anthracite-region, special causes operated to increase this evil. The mines were generally operated under 20-year leases, and royalties were paid upon such coal only as was actually marketed. The lessees consequently cared for immediate profit only. They were- not bound to win all the coal they exposed, or to leave it in such condition that their successors could win it. Nor was it their interest or duty to educate consumers in the use of their product. The market called for coal of large sizes ; and such coal they furnished, throwing away the rest. Any pains taken by them to bring about a more rational use of coal by their consumers would have borne fruit, after their leases had expired, to the benefit of somebody else. A full statement of the situation wits given in 1893, in the report of the State Commission, appointed in 1889 to investigate the subject.` That body included the names of Heber S. Thompson, William Griffith and the late Eckley B. Coxe.2 Its report gives special attention to the utilization of the old culm-banks.

Nov 1, 1905

By W. P. Frey

The briquet plant of the Lehigh Coal and Navigation Co., at Lansford, Pa., has previously been referred to.&apos; It has passed the stage of experiment and now rests on a foundation practically and financially sound. The purpose of this&apos; paper is to explain how success has been attained, and to set standards for the development of hard-coal briquetting which may eliminate future failures. All the conclusions are based on actual results, avoiding speculation and theory. Up to three years ago, the L. C. & N. Co. used coal-tar pitch as a binder in making hard-coal briquets. The plant operated with a monthly output of 300 to 600 tons and was unable to meet its own expenses. Naturally, no one was satisfied, especially as the ideals of a smokeless briquet were still unrealized. Then came the Dutch oil process, introduced in this country by the General Briquetting Co. of New York. This process uses as binder a small percentage of heavy residue of petroleum, which, being liquid, permits great economy of handling; it also did away with the most objectionable fumes of the former briquets. This oil2 is not absolutely smokeless; heating the fresh fuel to red heat liberates some low-volatile hydrocarbons, yielding a white smoke which is not objectionable. On the other hand, this oil adds to the briquet about 7 per cent. of volatile matter, giving the product a heating capacity equal to that of the best free-burning anthracite coal. The average silt used in the manufacture of these boulets averages 16.5 per cent. chemical ash, corresponding to 12,000 B.t.u. per pound of coal. The Hydrolene used as binder runs about 17,500 B.t.u. per pound, and approximately 7 per cent. of it enters into the mixture, hence 12,000 X 0.93..........................11,160 B.t.n. 17,500 X 0.07.......................... 1,125 B.t.u. Total.....................................12,385 B.t.u. per pound of briquets

Jan 1, 1918