Search Documents

By A. Perry Thompson

I- GeneRal Distribution, AppeaRance, and Relations ........ 563 11. Data fRom MicRoscopic Examination............... 568 1. Criteria for Distinguishing Primary from Secondary Minerals...... 568 2. The Leonard Vein Filling..................... 574 Quartz............................ 575 Pyrite............................ 575 Enargite............................ 576 Covellite............................ 578 Bornite............................ 581 Chalcocite........................... 583 Chalcopyrite.......................... 586 3. The Fault-Vein Covellite..................... 587 The Speculator Ore........................ 587 The East Gray Rock Ore.....,.............. 589 4. Other Occurrences of Covellite.................. 591 111. Conclusions........................... 592 1. The Replacement of Minerals..................592 2. The Character of Mineralizing Solutions .............. 594 I. General Distribution, Appearance, and Relations Mining in Butte has seldom encountered covellite in commercial quantities. The notable occurrences, extending vertically and laterally perhaps several hundred feet, presented scattered, bladed lenses of this mineral in a matrix of quartz, pyrite, enargite, bornite, and chalcocite. But under the microscope covellite is seen to be widespread in the Butte ores, though in such small quantity that megascopic examination will not discover it. In early mining operations covellite was found in the Gray Rock vein, a member of the Blue vein system. As described by Sales,' it persisted as an occasional ore mineral, associated with quartz, pyrite, tetrahedrite, bornite, chalcocite, and minor amounts of sphalerite, from the 700-ft. to the 1,200-ft. level of the East Gray Rock and Diamond mines. Crushed quartz-monzonite and later quartz completed the vein filling between

Jan 1, 1916

By Chester Wells Purington

Situation.—The Camp Bird mine is in Imogene basin† (Fig. 1) at the head-waters of Canon creek, a branch of the Gunnison, in the southern part of Ouray county, Colorado, towards the northern edge of the region known as the San Juan mountains, and about 10 miles W. of the continental divide. It is 8 miles by wagon-road from Ouray, the terminus of a branch of the Rio Grande' Southern railway. The distance from Denver to Ouray is 387 miles by rail. In an air-line, the mine is 190 miles SW. of Denver. The altitude of the town, tunnel and buildings is 11,200 ft., and level No. 2 is 11,500 ft., and No. 1 is 11,670 ft., above sea-level. The lowest point of the lode-ontcrop, which crosses the basin E. and W., has an elevation of 11,850 ft., and that of the highest point, on the divide between Imogene and Tomboy basins, is 13,250 ft. On the eastern slope of the Imogene basin (towards Ironton) the vein is less clearly defined on the surface. Ownership and Extent.—At the time of the writing of this paper, the property is owned by Mr. Thomas I?. Walsh, and operated under the management of Mr. J. W. Benson. It

Jan 1, 1903

Jan 1, 1881

By George M. Fowler, Joseph P. Lyden

PaGE Scope of this Report.................................................... 206 Production of Tri-State District.......................................... 207 Historical Sketch....................................................... 207 Location and Topography............................................... 211 Geology............................................................... 212 The Tri-State District.............................................. 214 Stratigraphy........................................................... 217 General Geological Section in Tri-State Region....................... 217 Stratigraphic Section of Mineralized part of Boone Formation........... 218 Stratigraphic Section Bird Dog Well.................................. 219 Metamorphism........................................................ 220 Structure............................................................. 225 Regional.......................................................... 225 Due to Metamorphism.............................................. 229 Ore Deposits.......................................................... 231 Types............................................................ 232 Hard-ground Deposits.......................................... 232 Brecciated................................................. 232 Stratified............................................ 232 Sheet Ground............................................. 232 In Dolomite............................................... 233 In Shale.................................................. 233 Soft-ground Deposits.......................................... 233 In the District as a Whole....................................... 233 Ore Minerah and Analysis......................................... 233 Paragenesis....................................................... 234 Conclusions........................................................... 236 Structure.......................................................... 236 Genesis of the Ore.................................................. 237 Future of the District............................................... 239 Acknowledgments..................................................... 239 Discussion............................................................ 239 Scope of This Report The Tri-State district. as outlined in this paper. refers to the entire mineralized area in sout'hwestern Missouri. southeastern Kansas and

Jan 1, 1932

By J. O. Edstrom, G. Bitsianes

Parabolic rate constants were determined for the formation of wiistite by the solid state reaction between magnetite and iron. The reaction was diffusion controlled and inert marker studies indicated that the mass transport through the wiistite layer was accomplished by means of iron migration. Relationships between rate constants and self-diffusivities are discussed. The transport capacity for iron through dense wustite layers was found to be sufficient to carry on reduction, even in gaseous reduction processes. REDUCTION of iron oxides has been the subject of many investigations. Most of the work, however, has been done on rather crude material and there have been difficulties in correlating the data on a quantitative basis. The reverse process of the oxidation of iron has been studied more thoroughly and usually by starting from the pure metal. As a result, the mechanisms of oxidation are now fairly well known.It has generally been found that the oxidation of metals follows the so-called parabolic 1aw;Q hat is, when the oxides are formed as dense layers, their thicknesses are proportional to the square root of the reaction time. This parabolic law follows directly from Fick's first law of diffusion The flux, J, is defined as the quantity of diffusing substance passing per unit time through unit area of a plane at right angles to the direction of diffusion. This flux is proportional to the concentration gradient of the diffusing substance, and the factor D, known as the diffusion coefficient, is introduced as the proportionality factor with dimensions of (length)'/time. If the flux is measured as the increase of thickness of the oxide layer (Ax) per unit time (t) and the assumption is made that the concentrations of the reactants at the phase boundaries of the layer are independent of time, Eq. 1 reduces to Integration of this expression yields the parabolic function ax = k . t. [31 The product of the diffusion coefficient and the concentration difference across the oxide layer is included in the constant k. When iron is exposed to a highly oxidizing atmosphere, the oxide phases are formed normally in a topochemical fashion, i.e., the interfaces between the phases maintain parallel positions to the original surface of the specimen. Above 570°C, the phases are orientated usually in the order of iron, wiistite, magnetite, and hematite, a condition in conformance with the requirements of the Fe-0 system. Below 570°C, the wiistite phase is unstable and has not been found as a normal constituent in the oxidation products of iron. There is a strong probability that continuous layers of the solid oxides are formed as the specific volumes of the phases increase in direct order from iron to hematite.' , ' Regarding mass transport through dense solid oxide layers, Wagner' has postulated that diffusion in oxides generally may be interpreted as migration processes of ions and electrons. There must be normally a concentration gradient across the growing oxide layer for diffusion to occur. This condition requires that there be deviations from the ideal stoi-chiometric composition of the oxide and accordingly deviations from the strict order of an ideal lattice. Such "lattice defects" include interstitial ions, cation and anion vacancies, quasi-free electrons, and electron holes and are decisive for all migration processes.' Cations, anions, and electrons all may have some mobility in the oxides but the movement of one of the particles generally far exceeds that of the others. Previous work', 1,2,7 has shown that during the oxidation of iron the migration through the wiistite layer, and probably also the magnetite layer, is confined to the movement of iron ions. Migration through hematite, however, has been found to take place by oxide ion movement. These behaviors are in direct agreement with the type of vacancies present in the respective oxides. Reduction of Iron Oxides The gaseous reduction of iron oxides, like the oxidation of iron, takes place in a topochemical fashion at distinct interfaces between the appearing phases."-'" Porosities might be expected in these reaction products, since their specific volumes are less than that of the starting material. Frank and van Der Merwe" have shown, however, that it is theoretically possible for nonporous layers to form if the degree of misfit in specific volume is less than about 15 pct. These aspects on porosity formation

Jan 1, 1956

ST. LOUIS SECTION EUGENE MCAULIFFE, Chairman, J. N. HOUSER, Vice-chairman, VICTOR RAKOWSKY, Vice-chairman., H. G. WASHBURN, Vice-Chairman, W. E. MCCOURT, Sec'y-Treas., Washington University, St. Louis, Mo. H. A. BUEHLER, G. H. COx, L. C. GLENN, E. A. HOLBROOK, W. E. NEWNAM. The eighth meeting of the St. Louis Section was held at the Mercantile Club on Apr. 15, 1918. ,, The meeting was preceded by a dinner, at which 51 members and guests were present, and at which T. T. Brewster presided. Bradley Stoughton, Secretary of the Institute, and Major J. R. Fordyce were the guests of the Section. A number' of the Joplin members were obliged to leave before the close of the dinner, in order to make train connections. The Vice, chairman, therefore, called on Victor Rakowsky, who brought a message of greeting from the Southwest district. At the close of the dinner, the Vice-chairman, T. T. Brewster, introduced Bradley Stoughton, who talked on various subjects of interest to members of the Institute, especially the affiliation of local sections with those of other national engineering societies. The minutes of previous meetings were read and approved-and-the Treasurer presented a financial report covering the previous year.

Jan 6, 1918

By Maxwell Adams

CONSIDERABLE interest has recently been developed in sage-brush oil because of its possible utilization as a flotation agent in the mining industry. A list of some of its physical properties, together with the method used in its extraction, may prove of interest at this time. Something over a year ago, a study of the essential oils in desert plants was begun in the Chemical Laboratory of the University of Nevada. None of the oils so far studied possess properties of special interest to engineers, except the oil of sage, Artemesia tridentate, which has exceptional power as a flotation agent. This plant, known as common sage brush, also called black sage, is widely distributed over the semi-arid West, being found quite generally on most of the dry plains and mountains west of Missouri. The method of extracting the oil followed in these experiments is very simple. The leaves, twigs and small branches are placed in an airtight drum, having a capacity of about 27 cu. ft. Steam is admitted through a number of small openings at the bottom of the retort, and the pressure maintained at 20 to 25 lb. per sq. in. for 3 hr. The escape of the steam from the retort is regulated by allowing it to pass through a stop-cock into a condenser. The water in the receiver is drawn off from time to time and the oil, which is insoluble and floats upon the water, is thus collected. At the end of 2 hr. most of the oil has been driven out, though traces continue to come over for a much longer time. By raising the pressure, the time required could probably be shortened and the yield increased, but the lack of laboratory equipment has prevented the carrying out of this experiment.

Jan 9, 1916

By AIME AIME

DONALD K. CRAMPTON, present Chairman of the Institute of Metals Division, A.I.M..E., is well known by nonferrous metallurgists in all countries for his research work on the fabrication and properties of copper and its alloys including investigation of season- and stress- corrosion cracking. He is also well known, at least by many metallurgists in the United States for the proficiency with which be carries on his hobbies, in i:lrlditlg photography. gardening, and golf

Jan 1, 1941

Iowa State College Ames, Iowa Iowa State Mining Society CARL S. NELSON, President NORMAN S. GEIST, Secretary K. A. PHILLIPS, Faculty Sponsor C. G. DRESSER, Counselor University Of Kansas Lawrence, Kansas University of Kansas Student Chapter of A.I.M.E. WALTER CROOK, President EDWARD C. MISHOU, Secretary E. A. STEPHENSON, Faculty Sponsor GEORGE M. FOWLER, Counselor K. A. SPENCER, Counselor .

Jan 1, 1942

By E. M. Wise

IN a previous communications the improvement in strength, harden-ability and color, occasioned by replacing gold in a typical gold-silver-copper alloy by various amounts of platinum, or palladium, was discussed. In the present paper the results of further studies upon the constitution and the nature of the hardening transformation in these alloys are pre-sented. This research may be summarized as follows: 1. The liquidus and solidus have been determined for the alloys of the palladium and platinum series. Cooling curves were utilized for deter-mining the liquidus of the palladium alloys but this method proved unsuitable for the platinum alloys so that a, novel quenching method was utilized for the latter. Both the liquidus and solidus of the palladium alloys increase steadily with the palladium content. The liquidus of the platinum alloys increases rapidly with the platinum content, while the solidus temperature increases with the platinum content up to about 14 atomic per cent platinum, but suffers no further increase with additional increments of platinum up to 20 atomic per cent at least, owing to a peritectic reaction. 2. Palladium, and even more effectively platinum, reduces the rate of grain growth. Owing to this fact and to the increase in the solidus temperature, "overheating" does little or no damage to alloys containing reasonable quantities of these elements. This is confirmed both by tensile tests and metallographic examination. 3. The excess phase present in one of the high-platinum-content alloys has been isolated and chemically analyzed and was found to consist almost wholly of platinum, gold, and copper, evidently derived from the compound AuCu, by the partial replacement of gold by platinum.

Jan 1, 1933

By G. Sachs, A. W. Dana, C. C. Chow

A great number of the investigations on the plastic flow of metals have been concerned with the establishment of a "universal" stress-strain relation. In such a relation some stress function when plotted against a strain function should yield identical curves for the various stress states. In the first investigation of this type, Ludwik and Scheu1 plotted the maximum shearing stress as a function of the maximum principal strain. Later Ros and Eichinger2 introduced two universal stress-strain relations, the one relating the maximum shearing stress to the maximum shearing strain, and the other relating a stress invariant, suggested by von Mises and Haigh, to the corresponding strain invariant. (In more recent investigations the stress and strain invariants are frequently supplemented with some factor to render their meaning more lucid.) A further suggestion which has not attracted appreciable attention is that by Baranski³ who used stress and strain deviators. The most common means of experimentation to determine the relation between stress and strain consists in subjecting thin walled tubes to combined internal pressure and axial tension.4a,4b,4c This method allows the study of plastic flow under stresses which are variable in two directions. However, the plastic flow which can be obtained in this manner is comparatively small, being limited by either tension failure or instability. For copper,'. only the relation between maximum shearing stress and maximum shearing strain yielded good agreement. On the other hand, tests on a stee14b and on an aluminum alloy4c. resulted in systematic deviations if any of the discussed universal stress-strain relations were used. It would seem, therefore, that the agreement mentioned above for copper is only incidental and explained by its high rate of strain hardening compared to that of other metals. Much larger strains than experienced in the tube tests can be obtained by subjecting a thin membrane of a ductile metal, which is restrained at its periphery, to a uniform hydraulic pressure. The thin sheet forms a deep bulge before it fails. The stresses and strains in such a bulge increase with increasing distance from the edge of the clamping "die," the maximum stresses and strains occurring at the pole (crown) of the bulge. While the stress and strain states are determined by the contour of the bulge, the absolute magnitude of the stresses and strains depends upon the hydraulic pressure. The bulge contour is in turn correlated with the geometry of the die opening. The deformation and fracture characteristics of circular bulges, that is, bulges formed with circular clamping dies, have been the subject of numerous experimental and analytical investi-gations.5,6,7 It has been shown that plastically deformed circular bulges develop large and comparatively uniform strains before failure by instability"6b,6c,6d and closely assume a spherical shape.6d Also the distribution of strains across the contour of the bulge is dependent on the metal being investigated and is correlated with, but cannot be predicted from, the metal's stress-strain characteristics. On the other hand, oblong or elliptical bulges, that is, bulges formed with elliptical clamping dies, are not as susceptible to analytical analysis and have not been investigated to the extent that circular bulges have. The few available data6c,7c indicate that stress states are obtained at the poles of the bulges, varying between plane strain and balanced biaxial tension, depending upon the geometry of the die opening. In this paper, the strain state and curvatures exhibited by three bulge shapes, a circular and two elliptical bulges, Fig 1, are analyzed experimentally using methods described in previous publications.6a,6c An attempt is made to derive the stress-strain relations for these bulges, which represent strain states in which the ratio of the two positive principal strains varied between 1.0 and 0.35. In addition, tension tests yielded data for a value of —0.5 for this strain ratio. Such an analysis should indicate the applicability of the various laws correlating stress with strain to the stress and strain states occurring in bulged shapes. Definitions and Nomenclature The definitions of the major stress and strain quantities used in this paper are as follows: s1, s2, s3 = principal normal stresses Sl > s2 > S3 t = shear stress e = conventional (unit) strain e = In (1 + e) El, E2, E3 = principal natural strains 7 = shear strain The maximum shear stress: , _ S1 — S3 lmax = 2 Frequently, the flow stress, s1 — s3 = 2lmax rather than the maximum shear stress is used.

Jan 1, 1950

By L. H. Robinson

Triaxial compression tests on Indiana limestone indicate that chemical additives in the pore fluids can increase or decrease the strength in plastic failure but not in brittle failure. Tests using a series of the sodium salts of dicarboxylic acids show that odd-number carbon-atom chains decrease the yield strength as much as 3.0 x 10 3 psi, and even-number carbon-atom chains increase the yield strength as much as 9.0 x 102 psi. ,The most effective chemical (sodium citrate) decreased the yield strength of Indiana limestone from 16.0 x 103 to 12.0 x 103 psi. The chemical additives investigated have no influence on microbit drilling rate when drilling with zero differential pressure. However, when drilling at a 2.0 x 103-psi pressure differeniial and using an odd-number carbon chain compound as the circulating fluid, the roller bit drilling rates were slower than with water whereas the drag bit drilling rates were faster. One even-number carbon chain compound added to the circulating fluid produces the opposite effect: the roller bit drilling rate is slightly faster than with water and the drag bit slower than with water. INTRODUCTION A Russian book by Rehbinderl published in 1944 generated much interest in the possibility of aiding and accelerating the destruction of solids by the action of a liquid in which the solids are deformed. This book describes a process in which microcracks are generated during elastic deformation. To describe this process, the rock is divided into three zones: (1) the zone in which the destruction takes place, (2) the predestruc-tion zone (an affected area immediately below the destroyed zone) and (3) the undisturbed specimen. Consider a load applied normally to a surface of an infinite slab of rock. Immediately below the point of application of the load, the rock is destroyed by compression or shear forces. Below this area of destruction, because of a great number of discontinuities ranging from defects to weak points in crystals of discontinuities in crystal latices, very small cracks are created in or between the crystals (often referred to as microcracks). Upon removing the load, the broken rock in the destroyed zone could be removed. In the lower predestruction zone, however, the microcracks in and between the crystals could disappear by the process of rehealing, i.e., the molecular attraction from one side of the crack to the other side being sufficient to completely eliminate the crack. Thus, a large number of these microcracks possibly exist only for a relatively short period of time. The concept of small cracks being generated within the crystals of a rock is not unreasonable. If the rock matrix is deformed below the yield point, some of the defects present within the crystalline structure could start small cracks through the interior of the grains. Upon removal of the load, these microcracks reheal (or the newly generated surfaces come back together) so that all evidence of cracks completely disappears. Under various types of loading, and in various types of fluids, the rehealing of these cracks would be time dependent. If a liquid adhered to the surface of a rock, it could penetrate into the microcracks and thus delay or prevent the rehealing process. This suggests that the prevention of healing of the microcracks may be dependent upon the wetting characteristics of the solid. Thus, rocks which are water-wet should be more easily destroyed in water than in nonpolar hydrocarbon liquid. Adsorption of a liquid could also reduce the free surface energy which could explain the decrease in strengths of materials under nonrepetitive-type loading. Rehbinder's work prompted Boozer, Hiller and Serdengecti 2 to examine the effects of pore fluids on the deformation of rocks subjected to triaxial compression over a range of confining pressures, temperatures and strain rates. Fluids which strongly adsorbed on the rock grain surfaces decreased the strength of sandstone and limestone, which deformed plastically. For certain strain

By Paul B. Barton

Unconventional mineral deposits are those that differ significantly from productive deposits in mineralogy, grade, or geologic setting. Thus, the initial representatives of each deposit type are, by definition, “unconventional” until they are exploited. The “unconventional” status changes to "conventional" because of economic shifts (e.g., bulk silver ores), because of technological innovations (e.g., froth flotation), or simply through the recognition of, and production from, novel mineral concentrations. Heretofore the discovery of new deposit types has been almost entirely accidental, but the long- established concept of the geochemical cycle provides a nearly untouched opportunity and challenge for the application of geochemistry in predicting novel, potentially economic, mineral concentrations.

Jan 1, 1983

New York Holds monthly meetings, except June, July and August J E SPURR, Chairman A D BROKAW, Vice-chairman SIDNEY ROLLE, Vice-chairman M H MERRISS, Secretary-treasures, Nichols Copper Co, 25 Broad St, New York M F CHASE KARL HOFFMAN Boston Meets first Monday of each winter month C R HAYWARD, Chairman E C GEITHER, Vice-chairman D H McLAUGHLIN, Secretary-treasurer, Rotch Bldg, Harvard Univ Cambridge, Mass GEO H GILMAN GEO A PACKARD

Jan 1, 1923

By Clarence Zener

Theoretical considerations by one of the authors have ledl to the prediction that the dynamic internal friction of annealed metals has a broad maximum at a certain grain size. This prediction they have verified2 for alpha brass. In the present paper the theory is extended to include the precise manner in which the internal friction varies with grain size on either side of the maximum. New experimental data are presented to test this extended theory. The physical basis for the type of internal friction that is being investigated lies in the interplay between stress and temperature. Just as local fluctuations in temperature give rise to local fluctuations in stress, so likewise fluctuations in stress give rise to fluctuations in temperature. But temperature gradients give rise to necessarily irreversible thermal currents, and hence to internal friction. The theory for this type of internal friction has been developed quantitatively,³ and has been experimentally verified,4,5 for the particularly simple case of the transverse thermal currents accompanying transverse vibrations. Of more fundamental importance are the intercrystalline thermal currents accompanying all types of vibration. The variation in stress across grain boundaries arises from the elastic anisotropy and at least partial random orientation of the individual crystallites. An exact quantitative treatment of the internal friction due to these thermal currents is of course out of the question. However, much information can be obtained from general arguments.1,6 Thus when the frequency of vibration f is low, or when the grain size d is small, adjacent grains remain nearly in thermal equilibrium, and vibration proceeds isothermally with little internal friction. Again, when the frequency is high, or the grain size large, the heat flow per cycle is small, the vibration proceeds adiabatically with little internal friction. The internal friction will become a maximum in the transition region. The degree of adiabatic-

Jan 1, 1940

By Clarence Zener

Theoretical considerations by one of the authors have ledl to the prediction that the dynamic internal friction of annealed metals has a broad maximum at a certain grain size. This prediction they have verified2 for alpha brass. In the present paper the theory is extended to include the precise manner in which the internal friction varies with grain size on either side of the maximum. New experimental data are presented to test this extended theory. The physical basis for the type of internal friction that is being investigated lies in the interplay between stress and temperature. Just as local fluctuations in temperature give rise to local fluctuations in stress, so likewise fluctuations in stress give rise to fluctuations in temperature. But temperature gradients give rise to necessarily irreversible thermal currents, and hence to internal friction. The theory for this type of internal friction has been developed quantitatively,³ and has been experimentally verified,4,5 for the particularly simple case of the transverse thermal currents accompanying transverse vibrations. Of more fundamental importance are the intercrystalline thermal currents accompanying all types of vibration. The variation in stress across grain boundaries arises from the elastic anisotropy and at least partial random orientation of the individual crystallites. An exact quantitative treatment of the internal friction due to these thermal currents is of course out of the question. However, much information can be obtained from general arguments.1,6 Thus when the frequency of vibration f is low, or when the grain size d is small, adjacent grains remain nearly in thermal equilibrium, and vibration proceeds isothermally with little internal friction. Again, when the frequency is high, or the grain size large, the heat flow per cycle is small, the vibration proceeds adiabatically with little internal friction. The internal friction will become a maximum in the transition region. The degree of adiabatic-

Jan 1, 1940

IRON AND STEEL COMMITTEE ALBERT SAUVEUR, Chairman A. A. STEVENSON, Vice-Chairman HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge,- Mass. Guilliaem Aertsen, Robert W. Hunt, E. Gybbon Spilsbury, John Birkinbine, J. E. Johnson, Jr., J. S. Unger, William H. Blauvelt, Charles Kirchhoff, Felix A. Vogel, Charles A. Buck, Richard Moldenke, Leonard Waldo, F. D. Carney, Charles F. Rand, William R. Walker, James Gayley, Joseph W. Richards, William R. Webster, Henry D. Hibbard, . C. F. W. Rys, . Frederick W. Wood. Henry M. Howe, Messrs. Guilliaem Aertsen, C. A. Buck, and F. D. Carney have accepted membership on the Committee.

Jan 3, 1914

CARL A. WENDELL, New York, N. Y. (written discussion*) .-I have never seen in print anything that even remotely has approached this article in clearness and important conclusions in conjunction with work done on the sink-and-float test. I have had many hundreds of these tests made and on different specific gravity solutions and the resultant product analyzed, but I have never grasped nor been able to show what this article sets forth. This article brings out one factor very clearly to my mind; what is to take the place of the solutions of different specific gravities used to obtain the laboratory results, when it comes to washing on a large scale, since water has one constant weight only? The answer is, sizing of coal. And as we know the importance of size versus specific gravity of the material to be washed, perhaps defined (practical) lines can ultimately be gotten up so that the sizing, if any, may be determined at the same time as the laboratory work on the coal is being done. G. R. DELAMATER, ? Steelton, Pa. (written discussion?).-The authors' deductions are well founded and although they disclaim any wide experience in commercial coal washing, practically all of the data presented are applicable to coals of all parts of this country. The paper clearly sets forth the great necessity of careful preliminary investiga-tion of each contemplated washery undertaking and contains the follow-ing very true statements. "It is not safe to assume that any coal which can he successfully washed on coarse coal jigs can be cleaned more com-pletely by washing at a finer size on tables," and "The effect of finer crushing upon the completeness with which impurities may be separated from coal depends upon two opposing tendencies. First, that the more finely a raw coal is crushed, the more completely will the particles of impurities be detached from the particles of clean coal. Second, the finer a coal is crushed the more difficult it becomes to separate the pieces of clean refuse from the pieces of clean coal."

Jan 12, 1919

By Stanley D. Michaelson, Norman Weiss

This was a year of realization. Some years are for planning and development, some for designing and building, others for fulfillment. With greater hopes and plans for the future than ever before, the year 1954, nevertheless, will be remembered principally because of project completion. Among copper mines, for example, there were Silver Bell, Copper Cities, Bisbee, Yerington, and White Pine. In iron, there were the Humboldt, Coleraine, Cerro Bolivar, and Eagle Mountain. In asbestos, Johns-Manville's new mill at Asbestos, Que. In uranium, completion of the ninth mill on the Colorado Plateau-Kerr-McGee's at Shiprock, N. M. In research, 1954 marked the completion of Kennecott's Research Center in Salt Lake City, one of the historic forward strides in the science of minerals beneficiation. The year was fruitful in other directions as well. Investigations of a fundamental nature were on the upswing, and pilot plant projects have also increased in size and number. Progress in new reagents and equipment was greater than normal. It can already be conservatively predicted-from the technological point of view-that 1955 and 1956 will be tremendous years.

Jan 3, 1955

By F. E. Bash

IN recent years, there have been a number of experiments conducted to determine the rates of heating and cooling of various sizes and shapes of steel ingots. Up to date, however,-most of the published data has dealt with small sized ingots, the largest being an 18-in. (46 cm.) cube, the data on which was presented before the Iron and Steel Institute in May, 1918, by E. F. Law. It is due to thus lack of information on the rate at which large ingots absorb heat and come to temperature that the heating- practice varies so widely in different plants. One of the questions over which there is much debate is the proper rate of heating of large ingots for forging and the time actually required for the center of a mass of steel to come to forging temperature. As a continuation of experiments described by M. E. Leeds1 and at the request of Mr. G. R. Norton of the Sizer Forge Co. and Mr. R. C. Drinker of the Emergency Fleet Corpn., the test described in this paper was carried out on a 24-in. (61 cm.) round ingot and the rate of heating and cooling determined under regular production conditions. The ingot had been partly forged at one end but, on developing a flaw, had been scrapped so that it was available for test. The size and shape of the ingot and its position in the furnace are shown in Fig. 1.

Jan 9, 1919