Search Documents

By R. E. Old

Through the use of pressure and production records, formation properties and bottom-hole sample data, the performance of an oil reservoir may be studied analytically to define and evaluate the natural forces acting on and within the reservoir. Use is made of material-halance methods and the equations for natural water encroachment. to estimate reserves. Methods for calculation of pressures are given. A study of the Jones sand, Schuler field, Arkansas, has been made and is given here to illustrate the value of the methods discussed. Introduction With the decreasing rate of discovery of new oil reserves, attention is necessarily focused on the efficient development, evaluation, and production of existing reserves. From the nation's viewpoint, the necessity of conserving resources is obvious. From the operator's viewpoint, the problem is to lengthen the period of profitable operation, in an attempt to increase the return on his investment. To do this the operator must take advantage of the natural forces acting on and within the reservoir. Natural water encroachment, the nemesis of profitable operation in the past, can be and is being harnessed to produce a greater oil recovery during the stage of flowing production. Proper evaluation of water encroachment rates and a fuller under- standing of reservoir behavior dictate the appropriate production procedures. Complacency in hit and miss production is obsolete. Oil production must and will approach the efficiency of other businesses, such as manufacturing. A manufacturer will not place an article on the market until he has fully investigated the processes involved, additional investment in equipment, costs of production, and expected profits. These may be modified by actual experience at a later date, but at least he begins with an idea of expected return. It is just as logical that an oil operator should investigate these same factors during the development and the early period of production of an oil reserve. The complexity of the problems existing in oil reservoirs should not be underestimated. Conversely, they should not be regarded as insoluble. Many completely defy solution, but there are others that can be solved completely or attacked intelligently to yield approximate results. The petroleum engineer has many tools, both figuratively and literally, at his disposal. Physical data such as core analyses, electrical logs, bottom-hole sample analyses, and bottom-hole pressures are accumulated extensively. Advances in the analytics of fluid flow have kept pace with the advances in measurement of physical data. It is the purpose of this paper to show how some of these records may be analyzed to define certain phases of reservoir behavior.

Jan 1, 1943

By Pervez Patel, Martin G. Frohberg, Demetrios Papamantellos

Model experiments were carried out on the mass transfer of iodine between n-hexane and a 4 2 X 10-3 M aqueous sodium hydroxide solution. The influence of mechanical stirring by means of small gas bubbles (ca. 0.01 ml in volume) on mass transfer was examined in independent experiments. The results were described with the help of the penetration theory and in the case of bubble stirring with the help of a mathematical model based on this theory. S LAG-METAL reactions, especially those in steel-making processes, often occur under conditions where gas is evolved in the form of bubbles that break through the slag-metal interface. It is known that stirring by means of bubbles increases the mass transfer coefficient, but there has been very little quantitative work done in this field. Because of the difficulties that attach to experimental work at high temperatures this study was confined to model experiments at room temperature. EXPERIMENTAL APPARATUS The transport of iodine from an n-hexane layer into a weak sodium hydroxide solution was studied a) with stirring by means of bubbles and b) with mechanical stirring. The apparatus for the experiments with bubbles consisted of the cell, two Dreschel bottles filled with hexane in order to saturate the nitrogen flow, one flow meter, and a nitrogen gas cylinder fitted with a fine-regulating valve. Fig. 1 shows the cell consisting of a glass cylinder 33 cm in height with an overall diameter of 7.5 cm embedded in a copper flange. The flange is connected to a Plexiglas plate and to the gas inlet. The Plexiglas plate has holes of 0.2 mm diam bored into it which are spaced 1 cm from each other. For the experiments with mechanical stirring the bottom of the cell was sealed off by a Plexiglas plate. The upper layer was stirred by means of a glass stir-rer and the bottom layer with the help of a magnetic stirrer in a counter rotatory direction. Both stirrer speeds could be varied continuously. EXPERIMENTAL PROCEDURE Iodine dissolves in n-hexane producing a stable violet color thus enabling the iodine concentration in

Jan 1, 1970

By Byron M. Bird

JIGGING is the stratification of a mass of solid particles in upward pulsations of water or in alternating upward and downward pulsa¬tions. The stratification usually is effected in a rectangular open¬top container having a perforated bottom through which the pulsations of water are applied to the materials to be separated; in separating coal, to a mass of coal and refuse. Jigging usually is a continuous process involving three steps: (1) the reception of the raw coal, (91) the stratification of the coal and refuse so that the refuse settles to the screen plate, and (3) the overflow of the cleaned coal and the withdrawal of the refuse collected on the screen. The jig is the most universal washer ever devised. It is handling in practice a wide range of closely sized coals and ores, mixed sizes of coal from 8-in. to 0 through %-in. to 0, and mixed sizes of ores down to %3 O-in. to 0 and even smaller. It is treating materials ranging in specific gravity from that of gold at 19 to that of coal at 1.30. It is handling feeds in which the proportions of high-gravity materials range from 90 per cent or higher, as for some iron ores, to 10 percent or less for some coals. It is handling feeds containing all shapes of particles-round, rectangular, and flat. It is handling simple separation problems and difficult separation problems. Thus, it is an almost universal separating device. One might add that it has been one of the most misunderstood types of washers, from both a theoretical and a practical point of view. Although con¬siderable progress has been made in coal jigging in the past 10 years, the jig probably has more unexplored possibilities than any other type of washer. In this chapter the object has been to treat the jigging process in a practical manner and to give information that will help the reader to improve his particular operation. Inasmuch as performance data from operating plants would contribute little of value, none has been given. Instead, the emphasis is upon jigging principles as a foundation for attacking the problems that arise. These principles are in reality tenta¬tive conclusions from research in the field of jigging during the past 10 years and most of this chapter should be regarded as a progress report on an investigation still under way.

Jan 1, 1943

By David Baker

IN a paper presented to the American Institute of Mining Engineers, September, 1904, entitled ? Improvements in the Mechanical Charging of the Modern Blast-Furnace,"' I showed the great fault of mechanical charging-devices to be that the materials charged by the dumping of the skip were separated, the coarse materials having high velocity, and the fine, low-thus giving paths of low resistance through the stock in the furnace, which resulted in unequal distribution of the furnace gases, unequal reduction, slips, scaffolds, irregular cutting of the. inwall, " off " iron, and increased fuel-consumption. I showed how this could be prevented by rotary distribution, through which the irregular distribution in one layer charged is compensated by charging the subsequent layers from successively varied positions of the charger, and becomes practically eliminated when the angle between two successive positions is a little more or less than an even fraction of a full circle. Of all the devices then on the market, the nearest approach to the ideal arrangement was found in the Brown distributor, a full description of which was given. The one defect pointed out, however, was the difficulty of maintaining so much mechanism on the top of a blast-furnace. Since the presentation of that paper, I have designed a very simple form of rotary distributor, which may be applied to any form of double-bell charger, retaining the perfect gas-seal, which is so admirably obtained by that construction. In seeking protection for this invention, I found no similar distributor on record in the patent offices of the various countries where application was made; but an application show-

Jul 1, 1906

By D. K. Crampton

ON giving thought to the subject of this paper, my first reaction was that many and striking changes have come about as a direct result of the war. However, more careful analysis indicates that few, if any, of these changes can be wholly attributed to it. The actual situation is that all these changes were conceived and most of them at least partially executed in re- cent prewar years, it remaining the role of war to achieve results in a fraction of the time that might normally have been taken, lacking its driving impulse. The further discussion will therefore be with the premise that the individual changes have been greatly hastened rather than directly and primarily caused by any war conditions. Co-operation among copper alloy producers on production problems is agreed to be much worth while. The industry was too long noted for jealousy and secrecy as to equipment, methods, and even materials produced. Gradually, a more open and co-operative policy evolved but even just prior to the war the interchange of ideas was relatively cautious and limited. The need for a great increase in production in record time fostered a more co- operative attitude; exchange of ideas and experience concerning all phases of production increased tremendously to the benefit of the individual participants and thus the war effort, too. This more united effort has undoubtedly led to many specific improvements in process or equipment and these in turn to more rapid and economical operation than could have taken place on an each-for-himself basis.

Jan 1, 1944

By Frederick G. Clapp

SINCE oil journals commenced to feature the progress of Iraq pipe-line developments and since newspapers undertook to follow the discussions between a certain large oil company and an Asiatic nation, I have repeatedly been asked questions that are only answerable by setting forth the essential geographic and historical facts of concessions in that part of the world. In so doing effort will be made to correct erroneous statements made in various quarters: and mistakes herein are being kept as low in number as possible. Perhaps the best-known concession in the Middle East is the one of the Iraq Petroleum Co., covering the greater part of the portion of the kingdom of that name- lying east of the Tigris River. West of the stream is the concession of the British Oil Development Co., which takes in all presumed petroliferous areas in western Iraq. No other important oil concessions exist in that country, except for the lands of the Khanikin Oil Co., which operates in "Transferred Territories" on the border of Persia. East of and continuous with the Iraq fields are those of Persia where the Anglo-Persian Oil Co. holds the well-known D'Arcy concession comprising three-quarters of the country, omitting the five northern provinces. This is the only valid existing concession in Persia, so far as known, except certain old firmans that permit development at Semnan in central Persia and possibly also certain regional grants to a French banking syndicate in eastern Mazanderan Province.

Jan 1, 1933

By HENRY M. HOWEL

1. Introduction.-The first part of this papers treats of the causes and the restraining of piping in steel ingots; the second& considers the causes and the restraining of -segregation; and the third proposes certain precautions in engineering specifications concerning these two defects. Into their causes I have looked carefully, with the purpose of arriving at rational methods of restraining them, and at efficient ways of detecting. and measuring the harm which they cause, so as to benefit the public by reducing this harm at once effectively and with the least expense to the manufacturer, and therefore in the end with the least expense to the consumer. In Part I., I infer that the pipe is chiefly due to what I, call the virtual expansion of the outer walls of the ingot in the early part of the freezing. I find that the upper and smooth-faced part of the pipe probably forms while the interior is still molten, but that the lower, steep, and crystal-faced part probably forms in metal which is already firm. Of the five causes which may co-operate to limit the depth of the pipe, I find that three-blow-holes, sagging, and the progress of freezing from below upwards-are usually effective. I find that the pipe may be lessened by casting (1) in wide ingots,; (2) in sand molds, especially if these are pre-heated (this is rarely expedient); (3) at the tops instead of at the bottom; (4) slowly; (5) and with the large end up; (6) by the use of a sinking-head or other means of retarding the cooling of the top; (7) by permitting blow-holes to form; and (8) by liquid compression.) Most of these I consider in some detail, and in particular I dwell on the advantages of casting with the large end up, and I propose certain administrative arrangements to permit this.

Mar 1, 1907

By Frank G. Breyer

THE .following developments in the zinc field during 1935 are listed in the order of their importance. Each will he amplified in later paragraphs. In the field o f Metallic Zinc: (1) Construction of further continuous vertical retort smelting capacity in the United States and Germany. (2) Expansion of fractional distillation capacity in the United States. (3) Great expansion in the zinc-base die-casting industry in the United States and abroad. (4) Wide acceptance of heavy galvanizing by the steel industry. (5) Construction of the first commercial wire electroplating plant for putting on heavy coats of pure zinc. (6) Firm establishment and appreciable expansion of the practice of using zinc dust as a reducing agent in the organic chemical industry.

Jan 1, 1936

By Joseph A. Holmes

I. INTRODUCTORY. THE plans for the investigation of fuels and structural materials now being conducted by the Technologic Branch of the United States Geological Survey were, before being decided upon by the Director of the Survey, submitted for consideration to the National Advisory Board, upon which there are nine representatives from the membership of the American Institute of Mining Engineers, viz.: Messrs. John Hays Hammond, Robert W. Hunt, B. F. Bush, and E. V. d'Invilliers (representing the Institute); Messrs. Julian Kennedy and C. S. Robinson (representing the Iron and Steel Institute); Dr. Charles B. Dudley (representing the American Society for Testing Materials); Mr. F. H. Newell (representing the U. S. Reclamation Service); and Dr. Richard Moldenke (representing the American Foundrymen's Association). It seems fitting, therefore, that a report of these investigations of the past three years should be submitted to the Institute for publication in its Transactions. The above, together with other representatives of the national engineering societies and allied organizations, were invited by President Roosevelt to serve, along with the Chiefs of the several Government Bureaus who have charge of public works and large. fuel purchases, on the National Advisory Board to give advice concerning these investigations. The appointment of this National Board grew out of a wish on the part of the President, the Secretary of the Interior, and the Director of the Geological Survey not only that the appropriations for these investigations be expended in a manner most beneficial to the several branches of the government

Jan 7, 1908

By Cecil H. Desch

THE progress of metallurgical practice and the demands made by the engineering industry on our foundries and mills have made the crystalline structure of metals a subject of far more than academic interest. Metals and alloys are made up of crystals. Even if we accept the view, so ably maintained by some metallurgists, that the crystals are separated from one another by an amorphous layer, it remains true that all but a very minute fraction of any metallic mass is crystalline. The conditions which affect the growth of crystals are therefore of importance in metallurgy. It is not only castings whose properties depend on the arrangement of their crystals, for the more we learn of the behavior of forged, rolled and drawn metals, the more certain it becomes that it is profoundly influenced by the size and arrangement of the crystals in the original ingot, deter- mining a structure which may persist in a modified form through a long series of mechanical operations and annealings. This is mainly due to the concentration of much of the impurities in the last portions of the liquid to freeze, so that the boundaries between single crystals or groups of crystals are marked out by a zone of segregated material, differing in properties from the mass, and offering a barrier to diffusion and equalization of composition throughout the whole. The importance of this fact has been fully recognized by steel manufacturers, who have to deal with ingots which are sometimes very large, and are cast at a high temperature, containing impurities which have a marked effect on the properties even when present in very small quantity. For this reason the Iron and Steel Institute has set up a committee to examine the whole question of the heterogeneity of steel ingots,(l)f and a report has been issued, containing an account of the structure of 16 ingots, ranging in weight from 15 cwt. to 172 tons, each of which was sectioned and examined by chemical analysis and by etching. A valuable body of data concerning segregation has thus been collected. The work of the committee is being prosecuted with great activity, and at the same time researches are in progress to determine the physical

Jan 1, 1927

By R. P. Carreker, J. C. Fisher

Cheep tests are normally constant load tests. Such tests approximate some types of service conditions and therefore are justified from the engineering point of view. Coupled with this consideration is the advantage of simplicity inherent in constant load tests, as contrasted with the comparatively complex requirements of a constant stress test. It is not surprising that the vast majority of creep tests reported are of the constant load type. Despite the enormous amount of accumulated creep test data, plastic flow is by no means completely understood. The widespread use of constant load tests is at least partly responsible for this lack of understanding. Any attempt to analyze deformation must involve the more fundamental quantity stress, rather than load. It is possible to predict constant load behavior from known constant stress data, but the reverse is much more difficult. When a metal specimen elongates, as in a creep test, the cross section decreases, maintaining constant volume. Thus For a constant stress test the force on the specimen must be decreased as the cross section decreases, that is, this force must be inversely proportional to the elongation of the specimen. An-drade has described three methods of obtaining the constant stress condition,l-3 each of which is relatively complex. The most recent proposal,³ suggests a major simplification which maintains the simplicity of the constant load test while approximating quite closely the desirable condition of constant stress. Andrade's device is admittedly more accurate but the method described below has definite advantages Consider a specimen in the form of a "V" supported at its ends. If a weight be applied at the vertex of the angle, the stress in each leg of the "V" If this stress causes an elongation ?1 in each leg of the "V," the angle decreases from a. to a smaller angle a1. The quantity sec — thus decreases with specimen elongation while the quantity 1/A increases. By selecting proper initial conditions it should be possible to hold S/So very nearly constant at unity. The proper initial conditions are realized when a0 is made equal to approximately 90°. Fig 1 compares the ratios of S/S0 for a0 = 85, 90, 95, 100°, with a0 = 0, that is, a straight speci- men, for true strains up to e = 0.10. It may prove convenient to measure X, the movement of the vertex, rather than the true elongation 1. Contour lines of X/lo are also plotted in Fig 1. The method for obtaining constant stress described above is especially suited to the testing of small wires, but may easily be extended to rods of any diameter through the use of a suitable grip which serves as the vertex joining two identical rods forming the legs of the "V." References 1. E. N. da C. Andrade: On the Viscous Flow in Metals, and Allied Phenomena. Proc. Roy. Soc., A, 84, 1, (1910-11). 2. E. N. da C. Andrade and B. Chalmers: The Resistivity of Polycrystalline Wires in Relation to Plastic Deformation, and the Mechanism of Plastic Flow. Proc. Roy. Soc., A, 138, 348, (1932). 3. E. N. da C. Andrade: A New Device for Maintaining Constant Stress in a Rod Undergoing Plastic Extension. Proc. Phys. Soc., 60, (3). 304, (March, 1948).

Jan 1, 1950

By A. E. Chute

The shortage of sulfur is not only continuing but appears to be worsening, attended by steadily rising prices. At the same time emphasis on air-pollution abatement is also increasing. These two factors, a rising market and the growth of environmental attention, have encouraged producers to carefully review all possible sulfur sources. As a result, production of sulfur from hydrogen sulfide occurring in petroleum is receiving greater attention than ever before. Until about a decade ago, the practice of recovering sulfur from hydrogen sulfide separated from gases (either found naturally or generated in desulfurization of liquid petroleum) was wide1y recognized but contributed little to total free-world sulfur production. However, during the past ten years, the production of sulfur from this source has increased so rapidly that it now accounts for a substantial portion of total production. This trend shows no signs of slackening, and current forecasts predict that recovered sulfur may become the dominant source of supply within ten years, exceeding mined sulfur production. This paper is intended to list sulfur sources and relationships, and to discuss the potential of producing sulfur from petroleum. The processing involved, in addition to product storage and transportation will also be discussed along with important economic aspects of sulfur recovered from hydrogen sulfide. For many years, most of the world's elemental sulfur has been produced from salt domes, predominantly by the Frasch process. During the past decade, however, another production source has developed so quickly that it is expected to surpass the Frasch production sources within a short time. This new source lies in the petroleum gases and liquids from which dramatically increasing quantities of elemental sulfur are being recovered. In the phraseology of the trade, the sulfur so obtained is know as "recovered sulfur," a term which does not, as one might expect, include sulfur recovered from other sources such as smelter gases. The growth rate of recovered sulfur compared to that of Frasch sulfur, total elemental sulfur, and total Free World sulfur in all forms is shown in Fig. 1 Since 1963, sulfur consumption has exceeded production,with the natural result that the price of sulfurhas continually increased. The posted price reported for f.o.b. Port Sulphur, La., has risen from as low as $18 per ton in 1962 to $32.50 per ton in mid-1967. With freight and other charges, delivered prices have of course run much higher, amounting to $45 or $46 per ton on the east and west coasts. In some cases, spot sales for as much as $60 have been reported. Although it is playing an ever-increasing role in the sulfur market, recovered sulfur was originally a by-product of the removal of hydrogen sulfide from natural and petroleum refinery gases. Today, however, it is often the most valuable product of a multi-product processing facility. Since there are two major sources of recovered sulfur—production and refining processes —natural gas is included with liquid petroleum for purposes of this discussion. Sulfur from these sources is produced in the form of gaseous hydrogen sulfide which is removed from a gas stream and converted to elemental sulfur. Gases in which hydrogen sulfide occurs naturally are natural gas and the gas produced from a high=pres-sure crude=oil or condensate field.

Jan 1, 1969

By K. K. Landes

The north central and northeastern states supply over 50 pct of the chemical and metallurgical limestone produced annually in the United States, and Ontario is the leading source of this material in Canada. About three fourths of the chemical and metallurgical stone produced in this area comes from Michigan, Pennsylvania, Ohio, and Ontario. The specifications, physical and especially chemical, for chemical and metallurgical stone depend upon the end use, but in general the tolerance for impurities is so low as to rule out most limestones and dolomites. Both high calcium limestone and dolomite are used in the metallurgical and chemical industries. The principal metallurgical use is as a flux in iron ore blast furnaces and open hearth steel furnaces. The major chemical uses are in lime burning and soda-ash manufacture. Other important uses include glass manufacture, in making calcium carbide, and in sugar factories. All deposits of high quality carbonate rock are definitely finite. Invariably and inevitably they diminish in either thickness or quality laterally so as to become unworkable as chemical and metallurgical stone. The size of these high quality lenses ranges from a few thousands of tons to hundreds of millions of tons. The best hunting for new supplies is in the geologic formations known to contain premium quality deposits. However, because of high transportation costs, carbonate rocks, to be workable, must be close to market, dollarwise. Definitions: Chemical stone is limestone or dolomite used as a raw material by the chemical industry. The major chemical uses are in lime burning and soda-ash manufacture. Other important uses include glass manufacture, making calcium carbide, and in sugar factories. The specifications for chemical stone depend entirely upon the end product. Some uses require dolomite, some require high calcium limestone; in a few instances, notably in lime burning, either type of carbonate rock can be used as raw material. As a general rule, a fairly pure stone is necessary and for certain particular uses the tolerance for some elements such as sulfur, iron, and phosphorus may be extremely small. Metallurgical stone is used as a flux in furnace operations, especially in the blast furnace where iron ore is converted into pig iron and in the open hearth furnace where pig iron is made into steel. Either limestone or dolomite can be used in the blast furnace, but only high calcium stone is charged in the open hearth (except for rice-size dolomite used as a refractory). There are no rigid chemical specifications for blast furnace stone, but low silica, alumina, sulfur, and phosphorus are desirable. For open hearth use, in addition to low magnesia, a very low sulfur content is also specified by many furnace operators. For furnace use, fluxstone also must be sufficiently shatter resistant that it will remain in lump form during transport and charging into the furnace. Commercial stone is the term applied in the trade for crushed stone used for roadstone and in concrete aggregate. Many of our best chemical and metallurgical limestones are too soft to qualify in the Los Angeles abrasion test for use as commercial stone. However, some limestones, and a higher proportion of dolomites, do qualify for commercial stone and so can be sold to either market. Place Value: Even the highest grade limestone is still a bulk commodity with a relatively low value per ton. As a matter of fact there is very little difference in the average price per ton between high grade chemical and metallurgical stone and crushed limestone used commercially. Most high quality stone is produced in large operations with consequent low cost per ton whereas most commercial stone is produced in relatively small local quarries. As in the case of other bulk commodities most limestone buyers pay more for transporting the raw material than the cost of the stone at its source. For this reason steel furnaces and chemical plants

Jan 1, 1961

By AIME AIME

HARVEY MUDD, mining engineer and distinguished citizen, has achieved that balance between professional and civic activities for which many of us strive but few attain. His able direction of mining operations is known to many Institute members but perhaps few know that he was in 1936 recipient of the annual award given by the City of Los Angeles to that citizen who contributed the most valuable and unselfish service to the community. Mr. Mudd was born in Leadville,

Jan 1, 1944

By J. S. Owens, R. W. Marsden, J. W. Emanuelson, R. F. Werner, N. E. Walker

The iron ores of the Mesabi Range occur in a 340 to 750-foot thick, Precambrian cherty iron formation termed "taconite." For about 65 years, extensive natural iron ore bodies were mined, and the ores either shipped as a direct ore or processed by gravity methods to a shipping grade iron ore. Since 1956, magnetite taconite ores, occurring in magnetite-rich horizons in the Biwabik iron formation, have been commercially concentrated and agglomerated. The transition from natural ores to concentrating-grade ores is progressing rapidly so that, in the near future, a major percentage of the iron ore shipped from the Mesabi Range will be as iron ore pellets produced from taconite. Natural iron ores of the Mesabi Range occur in the Biwabik formation as trough ore bodies in elongated channels and as irregular and tabular deposits in fractured areas associated with faults and folds. Ore bodies range in size from a few thousand tons to hundreds of millions of tons and may occur in any part of the iron formation. In some areas of strong ore development, ore was formed from the hanging-wall argillite to the footwall quartzite. The natural ores and beneficiating-grade natural crude ores were formed by the oxidation of the iron minerals, magnetite, greenalite, stilpnomelane, minnesotaite, and siderite, to hematite and goethite and by the removal of much of the silica in the cherty quartz and in the associated silicates by leaching. The ores are believed to have formed by the oxidizing and leaching action of surface waters. Magnetite taconite ores occur as stratigraphic zones in the Biwabik formation where it contains sufficient magnetite to be concentrated profitably, by magnetic methods, to give a magnetite concentrate that is agglomerated into a high quality product. Unoxidized taconite has an extensive distribution away from and between channels of oxidation and leaching but only a part of the unoxidized taconite is of ore grade. Two general types of magnetite taconite ore occur: ( 1) magnetite taconite of the Main Mesabi Range, generally west of Mesaba, which is composed of magnetite associated with cherty quartz, greenalite, stilpnomelane, minnesotaite, and carbonates and (2) magnetite taconite of the Eastern Mesabi, generally east of Mesaba, composed of magnetite associated with quartz, cummingtonite, actinolite, ferrohypersthene, hedenbergite, fayalite, hornblende, pyroxene, garnet, and biotite. The Mesabi taconite is a metasediment derived from an iron- and silica-rich chemical sediment that has been regionally metamorphosed and, on the eastern end, additionally metamorphosed by the Duluth Gabbro Complex.

Jan 1, 1968

By D. W. Brunton

Discussion of the paper of D. W. Brunton, presented at the Spokane meeting, September, 1909, and published in Bulletin No. 33, September, 1909, pp. 837 to 855. WILLIAM' KENT, New York, N. Y.:-The Institute may congratulate itself on the opportunity of reading the splendid address of President Brunton. It is au admirable summary of the progress that has been made in the mining and metallurgical arts in recent years. The paper rightly give's the chief credit for this progress to the aid which has been rendered to these arts by the advances in mechanics, chemistry, and electricity. It is notable that most of the headings in Mr. Brunton's address refer to the work of the mechanical engineer, the electrical engineer, and the chemist, rather than to that of the specialist in mining-operations. It seems that. the most successful mining engineer of the present day is the one who makes the most intelligent application of the inventions and designs of engineers and others who are not directly engaged in mining. A tabulation' of the headings of the address, grouped as below, shows this most clearly. Work of the Mechanical Engineer-Rock-drills, hoisting-machinery, tramming, pumping, ventilation, dredging, sampling, concentration, briquetting, fume-recovery. Work of the Electrical Engineer-Electric machinery for hoisting, pumping, tramming, lighting and signaling, electric . transmission, electric smelting. Work of the Chemist and Metallurgist-Explosives, chlorination, cyanidation, roasting, lead-smelting, and copper-smelting. Work of the Geologist-Economic geology. Work of the Mining Engineer-Mine-mapping, surface-mining, timbering, tunneling; and planning and supervision of the work in general. The mining engineer of the present day, who is in responsible charge of a large plant, finds his chief work not in doing

Jan 1, 1910

By AIME AIME

FORMATION of a new company through the union of two familiar names in the mining and metallurgical world has just been announced. J. V. N. Dorr and E. L. Oliver have united the businesses and assets of The Dorr Company and Oliver United Filters, Inc., of which they are the respective heads, by the formation of the Dorr-Oliver Corporation under their joint management, and stockholders have approved the merger.

Jan 1, 1931

By John T. Norton

N order to attempt to arrive at a better under-Jl standing of the whole basic problem of sintering, these remarks will serve as an introduction for discussion that is included and will, perhaps, help to isolate specific questions which need to be answered or to suggest some definite avenues of investigation which should be followed. To bring some sort of logical order into the presentation, I will consider the various types of interaction between the metal to be sintered and the atmosphere which surrounds it, depending upon whether the phenomena are essentially chemical or physical in nature. For example, when the only necessary criterion for the satisfactory sintering of a certain powder is the removal of an oxide skin, then the problem of choosing a suitable atmosphere is primarily chemical; however, if a special surface condition as a consequence of the oxide skin removal is necessary for particularly effective sintering, then the problem becomes a physical one. Of course, the two aspects overlap considerably, but it may be possible to make a distinction in principle if not in practice. The chemical characteristics of the phenomena will be emphasized, since these are the better known. Metal-gas reactions involved in sintering are controlled primarily by the thermodynamics of the processes involved. In which direction will a reaction go and how far before it stops? The answer is to be found in the magnitude of the free energy change associated with the reaction. If a constituent is to be removed from the specimen as completely as possible or if a constituent is to be formed in the specimen as completely as possible, then one chooses conditions which are far from equilibrium so that the reaction is driven toward completion. On the other hand, if the composition is to be maintained at a desired value, then conditions are adjusted as closely as possible to the equilibrium point. This aspect of the problem is susceptible to quite precise analysis, provided, of course, that the significant reactions can be recognized and the required thermodynamic data are available. Conversely, if one asks how fast the reaction goes or how far it proceeds in a given time, the answer is frequently much more difficult to answer in quantitative terms. Yet the rate-con trolling factors of the reactions may be of primary importance in the success of a particular operation, especially where competing processes are at work. Both equilibrium and rate factors must be understood if a clear picture is to be obtained. For instance, in a process for carburizing titanium dioxide, is the difficulty of obtaining a stoichiometric Tic due to a true limitation of the equilibrium or simply to a very slow rate of reaction? An example of this appears in the work of Kalish and Mazza.' They showed that the oxygen content of sintered iron compacts was lower when sintered in pure hydrogen than in the case where the hydrogen was diluted with either argon or nitrogen. The equilibrium oxygen content of the iron would be the same in the two cases, since it is determined by the ratio of the partial pressures of water vapor and hydrogen and this pressure ratio is unchanged by dilution. The rate of oxygen removal, however, under the conditions of a constantly replaced furnace atmosphere, depends upon diffusion and thus upon the concentration of hydrogen in the furnace atmosphere. Possibly the clearest way to illustrate the interplay of these two factors is to consider in more detail some of the typical metal-gas reactions. Adsorbed Gases It is common experience that fine metal powders with their very large surface areas often contain large quantities of gas. This gas, which results from exposure to air or perhaps from some step in the

Jan 1, 1957

By Paul H. Lu

Methods and results of measuring three basic parameters for ground stability control, ground pressure, strata movement, and geomechanical properties of mine rock are presented in this paper. It is found that these parameters can be measured in situ by simple and practical techniques with nonsophisticated and inexpensive instruments. Specifically, a drillhole dilation technique employing a cylindrical hydraulic borehole pressure cell (CPC) was used to determine the modulus of rigidity. Premining ground pressures were determined by pressure convergence tests with a combination of one CPC and two pre-encapsulated flat hydraulic borehole pressure cells (BPC) installed in a single drillhole. Abutment pressures and pillar loading were monitored with BPC's. Differential strata movements and bed separations were measured with self-recording 10-anchor-point extensometers. Roof-to-floor convergence was measured with self-recording convergence meters. Some applications of these in-situ-determined parameters to mine design and ground stability control are also discussed.

Jan 1, 1984

Pulverized Fuel Combustion The apparatus shown in the illustration is a complete equipment f r supplying coal to boiler and metallurgical furnaces, cement and lime kilns, dryers, and to all furnaces requiring a temperature and quality of fame under prompt and easy control. It is claimed that the Aero Pulverizer makes practicable the highest efficiency obtainable from burning coal. It makes coal burn like a gas, a flame, the physical and chemical character of which is regulable- a flame that may be elongated or shortened, thus placing the zone of highest temperature where needed- a flame that may be made oxidizing, reducing, or neutral, as occasion may require. The coal is burned as pulverized, and there is no storage of the powder with its attendant hazard. Artificial drying before pulverizing is not necessary if the coal supply be sheltered from rain and snow. Where the Aero is used, it is wholly a furnace question whether a dryer should be installed; it is not at all a pulverizing or storage question. Labor is reduced to a minimum. Slack coal at low cost yields its last B.T.U.

Jan 11, 1915