Search Documents

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion, balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck .ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum, gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928

By Shiou-Chuan Sun

THE presence of an excessive amount of tough froth in the flotation of minerals, particularly coals, may create trouble in dewatering, filtering, and handling. Froth is also a nuisance in many chemical industries.1 This paper presents a study on the destruction of extremely tough froths with intense high-frequency sound. The data indicate that sound waves can be employed for continuous and instantaneous defrothing. A powerful high-frequency siren was used in obtaining the data. Also tested was an ultrasonorator of the crystal type with a frequency range of 400, 700, 1000, and 1500 kc per sec and a maximum power output from its amplifier of 198 w. The results, not presented, indicate that as now designed this machine is not suitable for defrothing. Although the sound generators of the magnetostriction type 2 3 and of the electromagnetic type 4 5 were not available, it is believed they are capable of producing the required sound intensity for defrothing. The use of ultrasonics for defrothing was suggested by Ross and McBain 1 in 1944. Ramsey 6 reported in 1948 that E. H. Rose mentioned a super-sonic device that broke down flotation froth but with low capacity. The writer has not been able to find any published literature containing practical experiments.

Jan 10, 1951

By Y. Kondo, S. Yamazaki, Z. Asaki

Thermal deco7nposition of Pyrite particles in a fluidized bed with inert gas stream was studied. Assuming that heat transfer from the surroundings to the fluidized particles controls the overall decomposition rate, rate equations for the batch process and for the continuous process were derived. In the batch experiment, a linear rate equation satisfies the experimental results and the overall heat transfer coefficient calculated from the rate constant agrees fairly well with that obtained by Leva.l1 For the continuous process, two rate equations were derived, one on the assumption of complete mixing of particles and another on the upward piston flow of particles in a fluidized bed. The former holds for a bed containing a higher fraction of decomposed pyrite realized at lower feeding rates. The latter can be applied for a bed at higher feeding rates. Thus, segregation of particles in the fluidized bed was indicated at higher feeding rates. Bed temperatures also correspond to these conditions. ThERMAL decomposition of pyrite may be represented by Eq. [I]. The pressure of diatomic sulfur gas reaches 1 atm at about 690°C. The thermodynamics,' kinetics,2'3 composition, and properties3-5 of decomposed products of such a reaction have been studied. Pyrite is a very common sul-fide mineral and is often accompanied with other sul-fides. It is of basic interest in nonferrous metallurgy to clarify the behavior of pyrite in the pyrometallur-gical processes of sulfide minerals of metals such as copper, lead, zinc, nickel, and so forth. Interest in this reaction increased recently because of possible elimination of arsenic from pyrite in processing highly purified iron oxide pellets. Producing elemental sulfur from pyrite, instead of sulfuric acid, also aroused interest in this reaction. It is indicated that the thermal decomposition of solid particles, such as calcium carbonate, proceeds through three major sequential steps: heat transfer, interfacial chemical reaction, and mass transfer.637 It is known that the decomposed product of pyrite is very porous2, 3 and the diatomic sulfur gas evolved can easily escape through this layer of decomposed product. It depends upon the circumstances, therefore, whether the heat transfer to the interface within particles or the chemical reaction at the interface determines the overall decomposition rate. The enthalpy change in the decomposition of pyrite is about 33 kcal per mole FeS2 which is comparable to that of calcium carbonate. The decomposition of calcium car- bonate becomes more and more dependent on the rate of transport of heat when reaction temperature increases, such as occurs in a fluidized bed.6'7 It is reasonable to presume, therefore, that the thermal decomposition of pyrite, an endothermic process, carried out in a fluidized bed may be analyzed according to the heat transfer controlling model. This work intends, first, to propose a mathematical model that determines the overall rate in a fluidized bed for the decomposition process and, second, to investigate a few characteristics of the fluidized bed based upon the experimental results obtained. KINETICS OF THERMAL DECOMPOSITION IN A FLUIDIZED BED It is intended in this section to obtain rate equations for thermal decomposition of pyrite in a fluidized bed by assuming that the overall rate is determined by heat transfer from the surroundings to the particles. Both batch and continuous processes are considered. 1) Batch Process. To obtain the rate equation in the batch process, the following two additional assumptions are made. First, the temperature of preheated inert gas, tg, blown into the fluidized bed is assumed to be the same as the temperature of the fluidized bed, tf. Thus, no heat exchange occurs between the gas and particles in the bed and only the heat transfer from the reactor wall kept at tw to the particles is to be considered. Second, the decomposition is assumed to start at the outer surface of the particles and to proceed toward the center. At any given time during decomposition, undecomposed pyrite remains in the tori at a temperature: td. The decomposed shell is composed of FeS1+x whose outer surface is at tp Diatomic sulfur gas evolving at the interface is heated to tf during its escape through the decomposed shell. This is illustrated in Fig. 1. With the above-mentioned assumptions of heat transfer, we have:

Jan 1, 1969

By W. F. Sullivan, J. R. Coleman

The use of radioisotopes in obtaining basic information on large scale industrial processing is illustrated with two examples. The first is concerned with the operating characteristics of a kiln scrubbing tower and the second with those of a Hardinge ore mill. The examples show the advantages associated with the industrial use of tracers as well as the limitations. The Atomic Energy Commission regulations governing the use of radioisotopes in this manner are also discussed. The nuclear properties of radioactive isotopes have provided a new technique for obtaining basic information on large scale industrial processing. A small portion of the process stream is made radioactive by mixing with a suitable radioisotope or by irradiation in a nuclear reactor. The "tagged" portion is then part of the normal process stream and can be followed by detection and measurement of the associated radioactivity. The advantages of radioactive tracing over other forms of tracers are well known, and include such factors as chemical similarity, capability of precise determination of very small quantities due to the high sensitivity of detection apparatus, and the absence of foreign element contamination of the final product. This report will illustrate two applications of the use of radioactive tracers in large scale industrial processing which have provided information that would have been hard to obtain by other means. The first is concerned with the operating characteristics of a kiln scrubbing tower and the second with those of a Hardinge ore mill. ATOMIC ENERGY COMMISSION REGULATIONS Atomic Energy Commission approval can be obtained by qualified personnel if the proposed quantity of radioactivity does not exceed AEC's standards for

Jan 1, 1965

By Charles A. Thomson

RECENTLY a prominent Brazilian' doctor wrote to an American friend: "I feel that cultural relations between the American and Brazilian people could be promoted in a very speedy and effective way by establishing contacts between men of the same professions. . . . A Brazilian mechanical engineer could be immediately interested in relations with American colleagues, even if he had never heard of Longfellow and was not interested in Stokowski's orchestra. . . . A large number of cultural ties could be established between specific groups of men who have already some common interest, and who, whenever they meet, can do something that naturally brings them closer, that is, `talk shop."' In appointing a committee on Inter-American Engineering Relations to cooperate with the Department of State in its program of fostering cultural relations with the other republics of this hemisphere, the American Engineering Council has taken a step which should lead to a greater sense of unity and fraternity among engineers of the Americas. That such unity and fraternity are part and parcel of the moral defense of the hemisphere is obvious. For years engineers of the United States have been traveling South and South-east to construct roads and bridges, dam rivers, harness waterfalls, build ports, install and operate mining equipment, and erect buildings and plants, often at the risk of life. Those in the teaching profession in this country have had as pupils a growing number of students from our neighboring republics whom they have sent back home trained in the most efficient engineering methods. In a sense, however, these relations with the other nations on this side of the globe have been haphazard and left to chance. Personal acquaintance among engineers has played its role but no organized attempt appears to have been made to take advantage of the natural relationship which geographical and historical factors should encourage.

Jan 1, 1940

By Murray F. Hawkins, Marion L. Kimmel

sage' appears to have been the first (1933) to design a rolling ball viscosimeter for the express purpose of measuring the viscosity of oils with natural gas in solution, i.e., under reservoir conditions. In 1940 Hocott and Buckley' further refined the rolling ball instrument in both design and method of operation, and their instrument, known as the Humble type, was the forerunner of present day viscosimeters used in petroleum production and research laboratories. They also initiated the technique of charging the viscosimeter with a sample directly from a bottom hole sampler. In 1948 the committee on engineering research 01 the Petroleum Division of the AIME in Part 3 (1) of

Jan 1, 1955

By Gernot Kostorz

In a recent paper, Raffo and itcheell1 compared solid solution hardening of various bcc alloy single crystals at room temperature and concluded that the expression for localized elastic interaction between dislocations and solute atoms2 that gives the critical resolved shear stress (CRSS) 7,: to = Z . µE3/2 C1/2 where c = concentration, e = misfit parameter, (µ = shear modulus, Z = numerical constant Fig. 1—The slope dT0/dc1/2 for niobium alloy single crystals deformed at 570°K plotted against the misfit parameter € = In' I + 1616 I. from Ref. 6, •estimated from Ref. 7. Table I. Plateau Hardening and Alloy Parameters for Niobium Alloys dT0/dc1/2, kg/mm2 Solute Ref. 6 Tantalum 3.7 ± 0.3 1.9 0.73 + 0.06 9 0.0 ± 0.5 15 Vanadium 16.1 ±1.4 - 0.69 i 0.01 9 -7.4 ± 0.5 16 Tungsten 12.5 ? 1.5 20.9 0.92 i 0.05 10 -5.0 t 0.4 17 Rhenium - 25.9 1.24 11.12 -8.5 ± 0.4 I5 Molybdenum - 14.6 1.04 13,14 -4.6 s†±?˜µ?fF?? 0.5 17 Hafnium - 13.9 0.37 12 4.8 ± 0.5 17 Table 11. Solid Solution Hardening and Alloy Parameters for Tantalum Alloys i)' dTo/dc1/2 kg/mm2, dTp/dc1/2 kg/mm2, Ref. 22 1006 Solute ˜570°K Ref. 7 See Text Ref. 25 Rhenium 44.3 32.5 0.65 -8.5 Tungsten 32.1 24.3 0.34 -4.6 Molybdenum 29.3 19.1 -0.19 -5.9 Niobium 5.8 5.5 -0.43 0.I

Jan 1, 1970

[FUQUA, H. B. and Thompson, B. E.: Oil and Gas Development and Production in North Texas for 1933, 107, 320; for 1934, 114, 417 Oil and Gas Development in West Texas 114, 438 FURMAN, W. F.: Heat and Corrosion-resisting Alloys. Printed in Oil & Gas Jnl., June 13, 1935 Furnace-bottom sand, uniformity, 73, 390 Furnace control, Isley apparatus, M27, 502 Furnaces (See also Holt-Dern; Blast Furnaces; Roasters; Wirebar, etc.): annealing: electric, 89, 424 gas-fired, 89, 425 gas vs. wood for nonferrous metals, 89, 422]

Jan 1, 1936

By A. Poll, J. E. Stantan, L. J. Jolley

THE basic problem in the generation of water gas from carbonaceous fuels and steam is the supply of the heat of reaction, and in general the source of this heat is the combustion of a further quantity of carbon with oxygen. Existing and proposed processes for complete gasification differ in the methods employed for transferring this heat to the fuel, and involve one or other of the following alternatives: 1. Use of a steam-oxygen mixture as the gasifying medium, so that the combustion and gasification reactions are combined. 2. Alternate passage of air and steam through a fixed bed, as in conventional water-gas production. 3. Cyclic passage of fluidized fuel through combustion and gasification zones. 4. Intense preheating of steam and of a portion of the gas made, and recirculation of this mixture through the fuel bed. 5. Supply of heat to the fuel bed through an externally heated wall. Except for the conventional water-gas process using large coke or low- volatile coal, only processes in the first group, operating with steam and oxygen, have proved practicable with fuels other than brown coals and lignites. A possible exception, which has not so far reached a commercial scale, is the moving-burden process developed by Imperial Chemical Indus- tries, Ltd. The cost of industrial oxygen is so high that its use can probably be justified only if it is attended by substantial savings in other directions; for instance, the use of cheap fuel. In the United Kingdom, no very cheap solid fuels are available, and it is unlikely that an oxygen-gasification process could compete economically with conventional production of blue water gas from coke. Hence particular interest attaches to all possibilities of making water gas without using oxygen, if any possible saving in fuel or other costs is involved. The cheapest and most abundant coals in the United Kingdom are the low-rank noncaking bituminous coals in small and ungraded sizes, typically those from the East Midlands coal field, and-fines of high ash content produced in coal-cleaning operations. A process capable of gasifying

Jan 1, 1953

By J. H. Nead

Discussion of the paper of J. H. NEAD, presented at the New York meeting, February, 1916, and printed in Bulletin No. 108, December, 1915, pp. 2341 to 2357. E. D. CAMPBELL, Ann Arbor, Mich.-Any one at all familar with research work can at once see that Mr. Nead has condensed into his tables and curves the results of a carefully planned set of experiments which must have involved a great amount of work on his part. He deserves much credit for the way in which he has carried out these experiments, for it is to the results of such systematic experimentation that we must look for further knowledge of the underlying causes which determine the physical properties of steel. It will probably be many years before we have sufficient knowledge of all the factors of the problem of the constitution of steel, but every set of carefully carried out experiments such as Mr. Nead has made adds something to our knowledge and brings us a little nearer to the final solution of the problem.

Jan 5, 1916

By Paul F. Kerr

QUARTZ of a certain kind, is one of our strategic minerals, and Brazil is probably the one important available source. Crystals of quartz of suitable size and perfection for piezoelectrical application are rare; their most outstanding use is in radio work. Clear quartz, or "crystal," free from twinning, cracks, foreign particles of other disturbing lines of growth, and gaseous or liquid inclusions, is cut into plates which provide excellent control of frequency in broadcasting. The squares or rectangles are less than a millimeter in thickness and ordinarily on the order of 1 in. along each side. They are cut at definite angles with respect to the axes of the crystal, and ground with opposite surfaces parallel. Each small slab must be a section of one crystal, uniform throughout in atomic alignment. The thickness of the chip controls the frequency of a broadcast and it is most important to have the plates oriented and ground with utmost precision. Opposite surfaces are parallel to within 0.001 mm. and expansion or contraction due to the temperature is limited to one part in a million.

Jan 1, 1942

By J. K. Stanley

Knowledge of the diffusivity of carbon in the low temperature form of iron (alpha iron existing below 910°C) is at the moment of considerable interest in the study of the decomposition of austenite and martensite, the elastic after-effect,123 the magnetic after-effect4 and the decarburization of steel below 910°C. Information on the solubility of carbon in iron, and to a lesser extent its diffusion, is also important in consideration of such phenomena as blue-brittleness, temper-brittleness, "magnetic" aging, quench-aging, strain-aging, and possibly the yield point. In order to obtain more information on these subjects more fundamental knowledge is necessary. It is the purpose of this work to present data on the diffusion and solubility of carbon in the alpha iron. The high temperature form of iron (gamma; face-centered cubic) existing above 910°C is capable of dissolving relatively large amounts of carbon, up to 1.7 pet at 1130°C, while the low temperature form (alpha, body-centered cubic) existing below 910° dissolves only a limited maximum amount of less than 0.02 pet carbon at 725°C, according to data obtained here. Since the solubility of carbon in the face-centered or gamma iron is large, relatively speaking, no great analytical difficulties have been encountered in the determination of the solubility lines5 or of the diffusion of carbon.0 The limited solubility of carbon in alpha iron offers difficulties because experimental procedures and analytical methods for low carbon contents below say 0.01 pet have to be more refined than techniques used for work with gamma iron. Because of the difficulties of applying conventional methods to the determination of the diffusion of carbon in alpha iron, virtually no work has been done on this subject. However, by proper refinement of the analytical method for small amounts of carbon, the determination of the diffusion coefficient can be made readily using modified procedures. The solubility of carbon in alpha iron has been determined over a temperature range by various investigators, but the agreement among them is poor. The present investigation establishes the limits quite accurately. Information of this kind is useful in establishing the correctness of equilibrium diagrams but, more significantly, such information on maximum solubilities, especially when extended to alloyed ferrites, should be extremely important in the study of aging and related phenomena. Literature The literature existing on the diffusion, in particular, and on the solubility of carbon in alpha iron is not extensive. The data which exist are not of a high order of accuracy, much of them being in the realm of conjecture. THE DIFFUSION OF CARBON IN ALPHA IRON Whiteley7 made the qualitative ob- servation, using metallographic techniques, that the rate of diffusion of carbon at the A1 (725°C) point was very rapid and that its diffusion was still rapid at 550°C. Snoek,4 studying the magnetic aftereffect in high purity iron, arrived at the conclusion that the after-effect could be explained by the presence of small amounts of carbon diffusing under the influence of magnetostrictive strain (lattice distortion due to magnetic interaction). In later work, Snoek8 made an estimate of the ratio of carbon diffusion in alpha to its diffusion in gamma iron, and concluded that for a temperature of 910°C the ratio of Da/D? was 2600. Polder,9 basing his calculations of D on relaxation phenomena in the elastic after-effect, estimated that Da is about 1/3 of D? at 910°C (1183°K) and is about 1/12 of Dy at 727°C (1000°K). Polder's equation for the diffusion of carbon in alpha iron was calculated to be 18000 D = 5.2 X 10-4 e-RT cm2 per sec Ham10 obtained data for the diffusion and solid solubility of carbon in alpha iron at two temperatures by using one technique similar to that employed in this study. He found a D of 8.0 X 10-7 cm2 per sec at 702°C and of 2.7 X 10-7 at 648°C. THE SOLUBILITY OF CARBON IN ALPHA IRON Although pearlite is absent in steels containing 0.06 pet,11 0.05 pet,12 or 0.045 pet C,13 it appears that the carbon in these steels cannot be in solution in ferrite. The solubility of carbon at the A1 (725°C) point was first determined by Scott14 on the basis of cooling curves, and was found to be between 0.03 and 0.04 pet C. Tamura15 by interpolating between the solubility of carbon in delta iron at 1400°C and in alpha at room temperature (assuming zero solubility) ar-

Jan 1, 1950

By J. M. Seeman, R. A. Dodd

If some solution-quenched supersaturated aluminum solid solutions, e.g.., Al(Cu), are plastically deformed at room temperature and then aged at 200oC, the hardness may first decrease before increasing in the usual manner ' A similar transient softening is observed, even in the absence of plastic deformation, when a thin foil or small-diameter wire Al(Cu) specimen is rapidly quenched from the solution-treatment temperature and then aged.' Also, some solution-quenched and neutron-irradiated alloys undergo an initial hardness decrease during subsequent aging.3 The usual explanation of the transient softening in the above examples involves the effect of vacancies introduced by plastic deformation, rapid quenching, and neutron irradiation, respectively However, the mechanism of softening is not unequivo-cably established. In the first-noted case, Gane and parkins' observed that the softening was approximately proportional to the difference in the atomic diameters of solute and solvent, and it was argued that, if a large relative difference in atomic diameter promoted vacancy-assisted room-temperature solute diffusion to dislocations, dislocation climb occurring during subsequent aging at 200°C could cause transient softening. Some substantiation of this theory was offered by the additional observation that discontinuous yielding of solution-quenched polycrystalline Al(Cu) tensile specimens was suppressed by interrupting the test for a short aging treatment at 200°C. Of course, reversion (resolution of GPI) at 200°C would also cause softening, and Sil-cock4 expressed the opinion that the softening in the case of Al(Cu) must be partly associated with reversion. Also, Hirsch5 commented on the possibility that, if jogs cause hardening, an anneal at 200°C should straighten the jogged dislocations and result in softening. However, parkins' has re-expressed his belief that these mechanisms are not entirely consistent with the observed serrated stress-strain curves. Experimental. New data has now been obtained for Al(Cu), Al(Ge), Al(Mg), and Al(Zn) primary solid-solution alloys. These alloys were prepared from metals exceeding 99.99 pct purity, and specimens 4 by 4 in. diam were solution-treated, quenched, deformed 10 pct in compression at room temperature, and aged at 200'C in a cottonseed oil bath for various times. Generally, these operations could not be carried out in rapid succession, so the alloys were stored in a freezer between treatments to minimize aging. The variation in hardness with aging time, Figs. 1 to 4, was determined by microhardness testing with a 3.0-kg load. At least five readings were averaged to obtain each data point, and all measurements were taken about the center circumference of each cylinder (region of maximum deformation). Each specimen was used to obtain only one data point, i.e., specimens were not replaced in the aging bath after measurements were made. In

Jan 1, 1968

By A. B. Wilder

We study the past Because it is a guide to the present and a promise for the future. The struggle for a better world is strengthened By the hopes, ambitions, and deeds Of those who were before us. As we look backward Our attention is directed forward. ONE hundred years ago, the manufacture of steel from molten pig iron without the use of fuel first began. In the earlier part of the nineteenth century the crucible process was the principal steelmaking method. It was a costly process, producing only a few pounds of steel at a time; so, most of the ferrous metal output was in the form of wrought or pig iron. With the perfection of the converter technique it became possible to produce low cost steel by the ton, thereby completely changing the structure, not only of the ferrous metal industry, but also of industrial production in general. This was the turning point from the Iron Age to the Age of Steel. William Kelly (Fig. 2), Sir Henry Bessemer (Fig. 1), and Joseph G. Martien experimented with the process before 1856. William Kelly began in Eddyville, Ky., in 1847 and has been given credit for first discovering the principle of the pneumatic converter process. Several years later in England Henry Bessemer independently conceived a steelmaking process similar to Kelly's. Bessemer made public his invention at the annual meeting of the British Association for the Advancement of Science held at Cheltenham, England, August 1856. As a result of his paper, "On the Manufacture of Malleable Iron and Steel Without Fuel," and his progressive leadership in the years to follow, the process became permanently identified with the name, Bessemer. Credit for the commercial adaptation of the process must be given two additional persons. Robert Mushet (Fig. 3) in 1856 in England recognized the necessity of deoxidation and recarburization of the converter product and evolved the technique for adding high manganese iron following the blow. In Sweden, in July 1858, G_ F. Göranson [ ]

Jan 1, 1961

Jan 1, 1911

By Frederick Jr. Prime

THE first catalogue of Geological Reports of the United States was prepared by Prof. O. C. Marsh, and published in the American Journal of Science and Arts for 1867, vol. xliii, second series. Since then the list has more than doubled, and it was thought that the publication of a new catalogue, brought down to date, would be useful to many of the members of the Institute of Mining Engineers. The compiler will be most thankful to have any omissions or inaccuracies in the list sent to him, to be published as a supplement in the next volume of the Transactions. Especially to have the correct title, number of pages, plates, and maps of any volume on the list to which an * is prefixed, as he has been unable to personally consult such works. A preliminary list was issued last February, which has been almost doubled by the kindness of many friends. The writer desires more especially to express the obligations he is under to the following gentlemen The Chief of Engineers, U. S. A.; Principal Dawson, Mr. G. M. Dawson, Drs. B. J. Harrington and T. Sterry Hunt, of Montreal; Mr. H. Engelmann, of La Salle, Ill.; Dr. F. V. Hayden and Prof. J. W. Powell, U. S. Department of the Interior ; Prof. E. W. Hilgard, University of California; Prof. Henry Y. Hind, Windsor, N. S.; Prof. C. H. Hitchcock, of Dartmouth College; Mr. Henry A. Holmes, State Librarian, Albany; Maj. Jed. Hotchkiss, Staunton, Va. ; Prof. W. C. Kerr, Raleigh, N. C.; Dr. J. S. Newberry, of Columbia College ; Prof. W. H. Pettee, of the University of Michigan ; Dr. Samuel H. Scudder, Prof. N. S. Shaler, and Prof. J. D. Whitney, of Harvard College ; Mr. Sanderson Smith and Prof. J. J. Stevenson, of New York ; Mr. Addison Van Name, of Yale College, and Lieut. Geo. M. Wheeler, U. S. Engineers. PHILADELPHIA, 907 Walnut Street, October 1st, 1879.

Jan 1, 1879

By R. Hadfield

Last year this institute was good enough to accept some remarks by the writer regarding sound steel, entitle Plant for Hadfield Method of Producing Sound Steel Ingots…

Jan 1, 1915

By David R. Mitchell

IF you are the owner of a mine, or a mine executive, or just an ordinary miner, and have a son about to go to college, do you urge him to take up mining engineering or do you try to dissuade him from such a course? If you live in the East, or the Middle West and your interest has been in coal rather than metal mining, the chances are that your young hopeful will be urged to do almost anything else rather than follow in father's footsteps.

Jan 1, 1939

By M. D. Banus, M. B. Bever, A. K. Jena

The heals of formation at 78", 195, and 273°K of the ternary compound h3SbTe2 based on the elements and based on the binary compounds In Sb and [inTe have been measured. The heats of formation at these temperatlcres of the binary compounds In Sb and In Te based on the elements have also been determined. Heal contents and free energies of the three compounds have been calculated from 0° lo 80I)°K. The free energies of joyrrzalion, heats of formations, and entropies of formation at 298°K have also been calculated. The results shown that the tertnary compound is metastable with vespecl to InSh and ln Te below 696 °K. bul is slable above that temperature. The weaker bonding of results in a positice entropy of formation which with incrensirzg temperature makes increasing negative conlvihtclions to the free energy and above 696°K renders the compound slable. THE ternary compound In3SbTez occurring in the quasi-binary system In Sb- In Te' forms on cooling at 829°K by a peritectic reaction.' Observations at 673" and 573 K have shown that this ternary compound decomposes slowly into the binary compounds InSb and1n~e.l'' It has not been possible to analyze the metastable behavior of the ternary compound because up to the present time data on its thermodynamic properties have been lacking. Some information on the binary compounds, however, is available. The heat of formation of InTe at 273°K and its free energy at 673°K are kn~wn.~'~ The heats of formation of InSb at 78", 273', 298", and 723°K have been measured5-' and its heat capacity between approximately 12" and 300"Kg9l0 is also known. In the investigation reported here the heats of formation at 78% 195% and 273°K of the ternary compound In3SbTez have been measured. The heats of formation of the binary compounds InSb and InTe at these temperatures have been obtained by combining new calorimetric results with previously published data. The heat contents and free energies of the three compounds at various temperatures from 0" to 800°K have been calculated. Against the background of this information, the metastability of the ternary compound will be discussed. 1) EXPERIMENTAL 1.l) Preparation of Specimens. The materials used consisted of the elements indium, antimony, and tellurium, the binary compounds InSb and InTe, and the ternary compound In3SbTez. The elements, obtained from American Smelting and Refining Co., had a nominal purity of 99.999+ pct. The compound InSb was Cominco semiconductor grade; the compound InTe was prepared from the elements by melting under a vacuum of 10-h m Hg followed by slow cooling. Three batches of specimens of the compound In3SbTez were used. One batch was prepared by melting appropriate amounts of the elements in an evacuated and sealed Vycor tube. The melt was held at approximately 100°K above the liquidus for about 8 hr, shaken repeatedly, and quenched into a mixture of ice and water. The specimen was annealed in vacuum at 760°K for 4 weeks. In preparing a second batch, a mixture of the component elements was melted and quenched in water. The resulting ingot was powdered. The powder was pressed into pellets, which were annealed in vacuum at 748" to 773°K for 4 weeks. A third batch was prepared in the same manner as the second, except that the starting materials were InSb and InTe rather than the elements. Metallographic examination of samples of the three batches and X-ray diffraction examination of a sample of the second batch did not reveal evidence of microsegregation or a second phase. The results obtained with the three batches showed no systematic differences. 1.2) Calorimetry. The calorimetric method has been described in detail." Samples of the compound In3SbTez, mechanical mixtures of InSb and InTe in the proportion of 1:2, and mechanical mixtures of indium, antimony, and tellurium in the proportion of 3:1:2 were added to a bismuth-rich bath at 623°K in a metal-solution calorimeter. These additions were made from 78°K (liquid nitrogen), 195°K (dry ice and acetone), and 273°K (ice and water). The heat effects of the additions were measured. The difference in the heat effects of the additions of a compound and the additions of the mixtures of its constituents, adjusted for differences in the concentration of the bath, is the heat of formation of the compound. In the concentration range not exceeding 1.5 at. pct solute, the heat effect of the additions was a linear function of concentration. The heat of formation refers to the temperature from which the additions were made, namely, 78", 195", or 273°K. Several calibrating additions were made in each calorimetric run. The calculated heat capacity of the calorimeter and hence the calculated heat effects of the additions of samples depend upon the values adopted for the heat contents of the calibrating substance. In this investigation bismuth at 273°K was used and a value of 4.96 kcal per g-atom was taken for (HGZ3"k . 2) RESULTS AND DISCUSSION 2.l) Heats of Formation. The heats of formation of the ternary compound In~SbTez from the component elements indium, antimony, and tellurium and from

Jan 1, 1968

NEW MEMBERS The following list comprises the, names of those persons who became members during the period June 10 to July 10, 1914: Members ALDRICH, HAROLD W., Supt. of Leaching Plant, Washoe Red. Wks., Anaconda Copper Co., Anaconda, Mont. AYER, FRANK ASHTON, Mine Foreman.. ..Detroit Copper Co., Morenci, Ariz. BELL, ARTHUR F. L., Chief Engr., Associated Oil Co.., 817 Sharon Bldg., San Francisco, Cal. BERGMAN, JULIUS GUSTAF, Mech. Engr., Chief Draftsman, Arizona Copper Co. Morenci, Ariz. BURT, CURTIS F., Min. Engr., Pittsburg-Dolores Mining Co., Rockland, via Yerington, Nev. CALLAWAY SCOTT DAVID, Chem La Harpe Smelter Co., La Harpe, Kan. CAMPBELL, W. C., Min. Engr 4 Princess St., Roodeport, Transvaal, So. Af. CARROLL, GEORGE A., Genl. Mgr Kildare Min. Co., Manson, B. C., Canada. CARUTHERS, JOHN LYTLE, Min. Engr., Asst. Engr., St. Louis, Rocky Mountain & Pacific Co.. Raton. N. M.

Jan 8, 1914