Search Documents

By G. H. Billings

The following data were collected some years since in the course of a series of experiments with oil as a substitute for coal in puddling, the earlier form of the Archer apparatus being employed. While I am not at liberty to give the name of the works at which the tests were made, I can personally warrant the accuracy of the record, and feel justified, therefore, in making this contribution to a discussion in which all trustworthy figures are likely to be helpful. Oil in Puddling. Starting with everything cold, we used 3518 pounds of oil to get the furnace in condition to charge a heat. After charging, we ran until we took out 13,340 pounds of puddled-blooms, using 8437 pounds, or 1333 gal1ons of oil. At 49 cents per gallon, the cost for oil per gross ton of blooms was $10.91; with coal at $4.871/2, and a consumption of 1.5 tons per ton of blooms (the usual quantity is ton for ton), the cost for coal is $7.31. The quantity of oil consumed in heating the furnace to the proper temperature and to make the bottom, is not included in the oil consumption stated. The quantity used was 3518 pounds of oil. Usually, the furnace need only be lighted, but in this case it had been repaired, and it was necessary to make a new .bottom. This required the quantity of oil necessary to make three heats of blooms, or 2109 pounds. Deducting this from the 3518 pounds leaves 1409 pounds of oil as the quantity consumed every week in lighting up.

Jan 1, 1889

Paper withdrawn from publication September 8,1977, after book was printed. Pages 258.272 are therefore omitted.

Jan 1, 1977

Jan 1, 1936

By C. E. Arnold

THE CHAIRMAN (PERCY G. BECKETT, Globe, Ariz.).-When you are at Miami tomorrow, you will see a very interesting comparison on the surface of the two mining methods that are being employed there largely. In the case of the surface over the Inspiration mining method, you won't see very much left of the surface. Everything has gone down. In the case right at the line of the Inspiration ground and the Miami, you will see that the surface over the top slicing which the Miami company has been doing in that country has been riding down evenly and uniformly; and it gives a very marked comparison of the two types of mining, and, to a certain extent, of the different degrees of waste dilution. I would ilke to hear from Mr. Maclennan on this subject. F. W. MACLENNAN, Miami, Ariz.-A paper based on percentage extraction by shrinkage stoping is a difficult one to discuss for the reason that it is hard to arrive at extraction figures until a section has been completely mined out. In the Miami mine we are using a method of shrinkage stoping with narrow stopes and pillars. This ore has been completely broken up and we have started in at the far end to draw off the ore mass maintaining the top of the broken ore dipping at an angle of 60° away from the direction in which we are retreating. A very important point I think about drawing a large. mass of ore down at an angle rather than trying to maintain the top of the ore more or less horizontal is that drawing at a steep angle has a tendency to create a horizontal movement in the ore mass as well as the vertical movement of the ore traveling down to the drawing off chutes. We know that this takes place, on account of the horizontal movement of marked

Jan 12, 1916

Jan 1, 1911

[ ]

Jan 1, 1938

New Products Equipment

Jan 8, 1951

By R. B. Sosman

INTRODUCTION WE have shown in the preceding paper that practically all natural oxides of iron contain a determinable percentage of ferrous iron, and in many cases the percentage approaches that in magnetite itself. Some of these oxides are true homogeneous solid solutions. Others are not homogeneous, and can be separated magnetically into fractions. The nature and cause of this inhomogeneity in certain special cases form the subject of the present paper. MAGNETIC FRACTIONATION OF OXIDES OF IRON The magnetic fractionation of a sample of oxide can be conveniently carried out by powdering the material very fine, and exposing it at various distances from the poles of an electromagnet. The magnet that we used was specially designed 1 to give a strong field together with a steep gradient outside of the poles. It is set in a frame, with the pole pieces directed downward. A glass plate can be adjusted at various distances beneath the poles. If the fine iron oxide powder is placed just beneath the glass plate, successive portions of the powder are picked up by the magnetic attraction and are caught against the glass plate, the most magnetic portions being taken up at the greatest distance from the poles. Some natural oxides can thus be separated into several-fractious of different magnetic susceptibilities. Among other natural iron oxides, we examined the powder obtained by crushing some crystals of hematite from Elba.2 We found that

Jan 6, 1917

By C. T. Malcomson

An elaborate series of experiments has been conducted during the past three years at Irvington, N. J., which has resulted in the perfection of a process for the manufacture of smokeless fuel from high-volatile coals, and for the recovery and refinement of the coal-tar products derived therefrom. These experiments have been financed by Messrs. Blair & Co., of New York, and were conducted under the direction of Charles H. Smith, a member of this Institute, and the inventor of the process. The low-temperature distillation of coal has interested investigators for many years. Sporadic attempts have been made to solve the mechanical problems, but until the Smith process was developed, they were not carried to conclusions of economic value. The present coal shortage and the increasing demand for smokeless fuels make this subject one of timely interest. DescRiption of Plant The following equipment was installed and operated during the experimental period: Four horizontal and two vertical units of commercial size for the low-temperature distillation of the coal; two vertical, two horizontal, and two inclined benches for distillation of the briquets at medium and higher temperatures; presses and auxiliary equipment necessary for making briquets; and a complete byproduct recovery and tar-refining plant. This commercial equipment is provided with gas and electric meters, pyrometers and other apparatus for recording accurately the results of all experiments. There is, in addition to the commercial equipment, a complete chemical laboratory with distillation and recovery apparatus, including facilities far refining and cracking the tar and measuring the yields and calorific value of the gas. This apparatus makes possible a study on a small scale, of the various problems involved in the process. Description of Process Mr. Smith's experiments have resulted in the production on a commercial scale of: 1. A fuel, called Carbocoal, which, for convenience in handling, is prepared in briquet form.

Jan 1, 1920

Jan 1, 1937

By L. P. Teas

The year 1932 has been one of exceptional significance for the Gulf Coast. Because of many new oil fields found, the most outstanding of which, Conroe, has assumed national importance, and because of new prospective areas extending through Montgomery, Polk, Tyler and Newton counties into Louisiana, there has been a stampede of operators to the Coast. During the year, development and discoveries have shown a marked trend away from the shallow or intermediate depth type of salt dome fields, with their treacherous flanking sands, to the deep-seated type of domes with their more continuous blanketing sands. The potency of some of the deep-seated domes such as Thompsons and Conroe, in Texas, and Iowa in Louisiana, has for the time at least, dispelled the disappointment of such deep-seated domes as Mykawa or Sheppard's Mott. Whether the newer deep-seated prospects, as yet little developed, will prove Conroes or Mykawas remains to be seen. In any event there is much for us yet to learn of the Coast. During 1932 a total of nine new oil fields and four new gas areas were discovered, which compares with seven new fields in 1931 and three fields in 1930. Of the nine new oil fields two were in Coastal Louisiana. This is the largest number of new oil fields found on the Coast in a single year since 1929, when 11 new fields were discovered. Not only because of the number of new fields has 1932 been notable but also because these new fields represent new productive areas that total 16,000 acres or more, or over 70 per cent of the total productive area known on the entire Coast at the beginning of 1932. In addition to the fields discovered in 1932, four new areas, or extensions around domes or fields already producing, and at least 11 new oil sands and three new gas sands have come to light. We may well say that 1932 has been the banner year for the Gulf Coast, in spite of depressed economic conditions and continued and more emphatic restriction of production. With the exception of 1901, when oil was discovered on the Coast and 1924, the year in which geophysical prospecting was in:lugurated, 1932 has been its most outstanding year.

Jan 1, 1933

By Raja V. Ramani, Jan M. Mutmansky, Ralph W. Barbaro

This paper discusses the effect of the computer revolution on Penn State's facilities and personnel and provides a short history of computer applications in mining in the Department of Mineral Engineering. The computer era began in 1955 at Penn State when the engineering faculty built a sizeable vacuum-tube computer. Since that time, a succession of machines has introduced many changes and presented a variety of opportunities and problems to the university's computer personnel and to the community of users. This paper discusses both the changes in computers and the accompanying problems that occur in a university computing environment. A historical summary of computer simulation programs developed within the Department of Mineral Engineering is presented along with information on computer applications in ventilation, statistics, mathematical programming, coal preparation, and other areas. Finally, computer plans for the future are discussed in terms of the develop- ments in the Charles B. Manula Computer Library and in terms of ongoing and future computer-related research projects.

Jan 1, 1983

By Frank Foote

PRECISION lattice-constant measurements have been widely used in the study of cubic solid solutions but as yet have been rarely applied to noncubic solid solutions. (See, however, references I and 2.) With the high precision at present attainable in the measurement of lattice constants, the X-ray method should be readily applicable to noncubic solid solutions. In the work reported here, hexagonal close-packed magnesium was used as the solvent and either lead, bismuth or gold as the solute. In the magnesium-lead and mag-nesium-bismuth systems the a and c lattice constants were determined as a function of composition, densities were calculated from these lattice-constant data, these theoretical densities were compared with those directly measured and the solid solubility limit was determined on quenched specimens over a considerable range of temperature. In the magnesium-gold sys-tem, the solid solubility is very small but we have obtained an indirect check on the solubility limit previously reported.

Jan 1, 1940

By W. T. Bishop

FOR many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. HISTORY The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and coat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree-rosin and turpentine-but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is, supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores" industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.1 In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1946

Jan 1, 1924

By F. M. Yans, A. D. Donaldson, A. R. Kaufmann

Beryllium was mixed by powder. metallurgical techniques with copper, nickel, iron, and chromium, respectively, to form beryllium -rich binary alloys which Mere then extyuded and rolled transtverse to the extrusion direction. The effect of each alloying element was determined by tensile testing. In solid solution, small amounts of iron and nickel had an embrittling effect, while copper in solution increased the strength but had no effect on ductility. The effect of chromium was complicated and not readily explainable. Observations concerning the planes and modes of fracture were made. BERYLLIUM possesses some very attractive properties for general design applications, especially its strength to weight ratio which is approximately twice that of aluminum and three times that of stainless steel. Equally significant, however, is its combination of high moduli , high strength (approximately 70,000 psi tension and 40,000 psi shear), and low density (0.0658 Ib per in.3), which has made it a potentially important structural material for use in high-speed aircraft and missiles. The main attractions of beryllium are most marked when compared to other constructional alloys now in use. For example, while its density is approximateiy that of magnesium, its modulus of elasticity is approximately seven times that of magnesium, three times that of titanium, four times that of aluminum, and 1 1/3 times that of steel. Furthermore, its relatively high strength and high melting temperature permit design for service temperatures to about 1100°F. It is felt by the aircraft industry in general,' that the high cost of beryllium can easily be amortized by the savings in fuel costs, and increases in aircraft payload and range. The only factor which has prevented the use of the metal in structural applications is its lack of sufficient ductility. It is this property that has retarded the development and utilization of beryllium. Beryllium's modes of deformation, Fig. 1 indicate that the main fracture planes at room temperature in a randomly oriented sample are the (0001) basal planes; the (1150) prism planes are the planes of secondary fracture.' Klein, Macres, Woodard, and Greenspan3 obtained elongations of up to 40 pct in beryllium sheet rolled above 700°C when the (0001) basal planes were oriented parallel to the plane of the sheet (see Fig. 2).

Jan 1, 1962

By A. D. Hughes

A relatively small area in Malaya, about 200 miles long by 40 miles wide, is the most important source of tin in the world. Some tin is recovered in other parts of the peninsula. Of the tin mined, 98 pct is recovered from alluvial deposits. From 1935 to 1941 the average annual world production of tin was 190,000 tons. The average annual production from Malaya during the same period was 62,000 tons or about one third of the total. Other producing countries, in order of importance, were the Netherlands East Indies 34,000 tons, Bolivia 30,000, Belgian Congo, Nigeria, Siam, Burma, China, and a few others with smaller amounts. The serious shortage of tin during the war period was due to the fact that the Japanese were occupying Malaya, Netherlands East Indies, Siam, Burma, and China which, together, formerly were producing 65 pct of the world supply.

Jan 1, 1949

YEAR OF ELECTION 1913. FRANK DAWSON ADAMS, Montreal, Canada. 1922. FEDERICO GIOLITTI Torino, Italy. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER Washington, D. C. 1941. DANIEL COWAN JACKLING San Francisco, Calif. 1939. HENRY KRUMB New York, N. Y. 1921. C. McDERMID London, England. 1913. EZEQUIEL ORDONEZ Mexico City, Mexico. 1935. ROBERT PEELE New York, N. Y. 1938. A.M. PORTEVIN Paris France 1937. JOHN V.W. REYNDERS, New York, N. Y. 1937. GEORGE S. RICE Washington, D. C. 1911. ROBERT H. RICHARDS Cambridge, Mass. 1934. T.A. RICKARD Victoria, B.C., Canada

Jan 1, 1942

1913. FRANDKA WBONA DAMS Montreal, Canada. 1921. WILLIAM CUTHBERTB LACKETT Sacriston, Durham, England. 1923. GELASIOC AETANI. Rome, Italy. 1929. TAKUMAD AN Tokyo, Japan. 1920. HENRYS TURGISD RINKER. Merion Station, Pa. 1922. FEDERICGIOO LITTI. Torino, Italy. 1906. SIR ROBERTA . HADFIELD. London, England. 1928. JOHNHA YSH AMMON.D. New York, N. Y. 1921. FRANKW ILLIAMH ARBORD London, England. 1917. HERBERTH OOVER. Washington, D. C. 1906. HENRI LECHATELIER. Paris, France. 1900. WALDEMAR LNDGREN Cambridge, Mass. 1879. JOHNM ARKLE .New York, N. Y. 1921. C. MCDERMID London, England. 1913. EZEQUIELO RDONEZ Mexico City, Mexico. 1909. ALEXANDRPEO URCEL Paris, France. 1911. ROBERT H . RICHARDS Cambridge, Mass.

Jan 1, 1929

By David K. Hylbert

This study investigated roof falls in room-and-pillar drift coal mines in eastern Kentucky and utilized geologic methods for predicting roof conditions in advance of mining. In the Highsplint mine, the roof was classified in four categories or conditions: Condition A and B (Laminated Shale); Condition C (Rolling Sandstone with Shale in Pockets); and Condition D (Zone of Major Sandstone Roll(s)). Structure contour and isopach maps of the Darby coal bed and associated immediate roof rocks were wed to project axial trends of the sandstone roof. Trend mapping in the mine and on outcrop provided more detailed control for roof projections.

Jan 12, 1978