Search Documents

By F. G. Jones, R. D. Pehlke, H. E. Gardner

The solubility of nitrogen in liquid Fe-18 pct Cr-8 pct Ni-0. 7 to 2.3 pct A1 alloys has been measured up to the solubility limit for the formation of aluminum nitride in the temperature range 1600° to 1700°C uszng the Sieverts' method. The solubility of nitrogen in 18-8 stainless steel increases with increasing aluminum content. Based on a nitride composition, AlN, the standard free energy of formation of aluminum nitride from the elements dissolved in liquid 18-8 stainless-steel alloys has been determined to be: ?G° = -42,500 + 20. IT in the range from 1600° to 1700° C. EVANS and pehlke1 have measured the equilibrium conditions for the formation of aluminum nitride, AlN, in liquid Fe-A1 alloys. The present study extends that work to the more complex solvent, liquid 18 pct Cr-8 pct Ni (18-8) stainless steel. Recent work by Small and pehlke2 has dealt with the effect of fourth-element additions on the solubility of nitrogen in 18-8 base alloys. They found the effect of aluminum additions, up to 0.74 pct, on the solubility of nitrogen to be small. The present study covered the range from 0.74 to 2.28 pct aluminum, and by extending the composition range may be used to better define the effect of aluminum on the nitrogen solubility in these alloys. EXPERIMENTAL PROCEDURE The Sieverts' method was used to measure the equilibrium solubility of nitrogen gas in liquid 18-8 stainless steel alloys containing 0.74, 1.49, 1.93, and 2.28 pct Al. The solubility was measured as a function of the nitrogen gas pressure at temperatures of 1600°, 1650°, and 1700°C. The apparatus used is the same as described by Small and Pehlke.2 The 100-g melts were made from Ferrovac-E high-purity iron, Crucible Steel Co.; 99.95 pct Cr, Union Carbide Corp.; 99.9 pct Ni, International Nickel Co.; and 99.99+ pct Al, Aluminum Co. of America. The aluminum was charged at the bottom of the crucible, surrounded by nickel and iron. The chromium was packed into the interstices to minimize vapor transport of the aluminum during initial melting. The hot volume of the system, measured for each melt with argon, ranged from 45 to 55 standard cu cm with a temperature coefficient of —8 x 10-3 cu cm per °C. The melt temperature was measured with a Leeds and Northrup disappearing-filament type optical pyrometer sighted vertically downward on the center of the melt surface. The temperature calibration of the system by Small and pehlke2 was assumed. Two problems are involved in determining the solubility product of a solid, metal nitride phase in liquid iron alloys. These are: 1) establishing the point of departure from Henrian behavior at the solubility limit of the metal nitride phase; and 2) determining the composition of the solid nitride which is precipitated. Determination of the solubility product of AlN was made by admitting small amounts of nitrogen into the reaction bulb until the deviation from Sieverts' law was clearly evident in the form of a pressure halt. To obtain the solubility product at several temperatures during one run the following procedure was used: 1) add increments of nitrogen to determine the Sieverts' law line at the lowest desired temperature; 2) continue to add nitrogen to precipitate a small amount of the nitride phase; 3) increase the melt temperature 50°C to dissolve the precipitated nitride; 4) repeat step 2 until either a nitride formed or the system reached ambient pressure; if a nitride formed at 1650°C, the sequence was repeated at 1700°C. The composition of the precipitated phase was checked by an X-ray diffraction pattern obtained from powder scraped from the surface of the solidified 1.93 pct A1 melt. RESULTS AND DISCUSSlON Solubility Measurements. Fig. 1 is a typical nitrogen-absorption curve obtained from measurements on a 1.93 pct A1 alloy. Since the initial absorption of nitrogen follows Sieverts' law the nitrogen solubility is plotted as a function of the square root of the pressure of nitrogen gas in the reaction bulb. The results of the solubility measurements for all alloys studied are summarized in Table I. The slope of the Sieverts' law line for each alloy was determined. Since this is also the solubility of nitrogen at 1 atm pressure of nitrogen gas, the latter designation is used for the data. It should be noted. however, that in most cases the value lies above the solubility limit for AlN. Fig. 2 shows the effect of aluminum on the solubility of nitrogen at this reference pressure and as a function of melt temperature. The solid portions of the lines represent attainable solutions; the dashed regions lie above the limit for precipitation of AlN.

Jan 1, 1969

By Charles A. Chase

This paper, descriptive of a single mine, is presented in the belief that it may furnish useful suggestions to mine-managers encountering similar problems; and it includes the details which will enable them to estimate the value of the methods employed—especially where these depart from common practice. Tt should be added, however, that this mine is not typical of the San Juan district, but differs markedly from neighboring mines in physical conditions and metallurgical requirements. The Liberty Bell mine is situated in San Miguel county, Colo., on the west front of the San Juan mountains, 2 miles north of Telluride. The vein was discovered in 1876 by Wm. L. Cornett, who, with subsequeilt locators, took up claims along the apex. A few hundred feet of development-work was accomplished, and a few? tons of ore were smelted or milled; but profitable working proved impossible under existing

Jan 1, 1912

By Leonard P. Skolnick

PROPERTIES of materials containing a hard con-stituent dispersed in a metallic matrix are dependent on the distribution of the hard phase.'-' The grain growth of titanium carbide in liquid nickel was studied in order to understand microstructural development in this and similar systems. Smith" has examined the influence of surface energy on the distribution of phases in alloys. The grain growth of tungsten carbide in cobalt has been the subject of many conflicting theories. Those prior to 1950 have been summarized by Goetzel.' Recently, Gurland and Norton3 and Gurland8 have indicated that growth occurs primarily by diffusion through the liquid phase in order to lower the inter-facial energy between the carbide and the liquid metal. In the development of the Ti-C-Ni ternary phase diagram, Stover and Wulff9 have shown that both eutectiferous dendritic titanium carbide, and primary titanium carbide which had developed crystals of cubic symmetry, were rounded by heating below the solidus, and that if primary carbide was already present the typical eutectic decomposition products were not formed. Experimental Procedure The infiltration technique was used to study the grain growth of titanium carbide in nickel. In contrast to sintering, infiltration more readily assures uniform dispersion of the two phases, and the problems associated with mixing by milling; i.e., mill contamination, breakdown of original carbide size in the operation, development of interfering surface films, etc., are avoided. In addition, the complicating effect of densification by shrinkage is eliminated. The titanium carbides used were commercial grades. Their chemical analyses, size distributions and shapes are summarized in Table I. Size analysis was conducted by microscopic count on a minimum

Jan 1, 1958

By Martin T. Broome

INTRODUCTION The Luanshya Mine is situated in the southern part of the Zambian Copperbelt. The copper ore deposit is stratiform, and is preserved in a synclinorium known as the Roan/ Muliashi basin. Roan shaft (formally called No.14 shaft) is located at the eastern end of the syncline and is theoldest of the presently operating hoisting shafts, being sunk during the 1930's. It presently hoists some 45 per- cent of the total Luanshya Mine production. A cross-section through the shaft is shown in figure 1. The ore formation on the south limb is unmined on this section because until recently it was believed that such mining might cause damage to the shaft. This paper examines the influences of adjacent mining on this so-called 'shaft pillar', and describes the mechanics of subsidence of the pillar itself. GEOLOGY AND STRUCTURE Figure 1 shows the general form of folding in the vicinity of Roan shaft. The north and south limbs of the main syncline approach parallelism, with the bottom of the trough fairly smoothly rounded. The axis of the - trough plunges to the west-north-west at 6° - l0°. A brief summary of the major lithologies present in the Roan basin is given in table 1, however, the performance of the overall structure during progressive mining of the ore horizon is controlled by the following features in addition to the mining method. Intraformational Contacts These are characteristically weak in most geological environments. The BC/RL7 contact is an unconformity between moderately weak quartz-biotite schists below (unconfined compressive strength 40 - 80 MN/M 2), and strong quartzites above (U .C .S. 170-200 MN/M2) Subsequent formations are conformable, and planes of weakness are generally the result of contrasting lithology (see below). Weak Interbeds The Rt7, RL6, RL5, RL3 and RU2 horizons consist predominantly of quartzitic rocks, i.e. conglomerates, quartzites and argillites, and as such are generally strong and considered suitable for the positioning of development. Between these however, lie two much weaker dolomitic horizons, the RL4 and RU1. The Rt4 is the main hangingwall aquifer, and must be drained prior to mining. Drainage results in an extremely weak, blocky cavernous horizon which usually requires support if exposed by development. Similarly, the RU1 formation is comprised mainly of dolomites and dolomitic arqillites which are weak and cavernous. In the eastern part of the Roan/

Jan 1, 1981

By H. R. Deeth, C. J. Koenig

ABOUT ten years ago nepheline syenite was introduced to the ceramic industry and the material has now found application in the various branches of the industry, namely, as a vitrifying agent in white-wares and as a source of alumina and alkalies in glasses, glazes, and porcelain enamels. Spence1 described the early mining and processing developments regarding this material. Since the time of his article many research papers have appeared relating to the usage of nepheline syenite but little has been published relative to subsequent mining and processing methods. A complete indexed review of the literature was issued recently by Ohio State University.2 Since "Lakefield" nepheline syenite from Blue Mountain, Ontario (Fig I); is the only commercial ceramic-grade nepheline syenite now being marketed on this continent, discussion is limited to this operation carried on by American Nepheline Limited, Lakefield, Ont., and its subsidiary in the United States, American Nepheline Corp. at Rochester, N. Y. THE DEPOSIT Blue Mountain is a long ridge rising to an elevation of about 350 ft at its highest point above the surrounding country and extending for about six miles in a northeasterly direction across Methuen township, Peterborough County. The rock of the Blue Mountain central alkaline intrusive is fine grained, light colored and of even granitic texture. The solidified mass consists predominately of the minerals albite, nepheline and microcline in order of abundance. The average mineralogical composition for the deposit obtained by a study of 112 samples taken regularly over the whole formation is as follows:3 [VOLUMETRIC MINERAL PER CENT Albite54 Microcline20 Nepheline22 Muscovite2 Mafics2 (Biotite, hastingsite, magnetite) Total100] The mineral nepheline (or nephelite) belongs to the feldspathoid group but is lower in silica content than are the feldspars. It is a silicate of soda, potash, and alumina (NaKAl2O32SiO2). Its presence with albite (Na2O A1203 6SiO2) and microcline (K20 A12O3 6SiO2) gives the Blue Mountain deposit an alkali content of 15 pct and an alumina content of approximately 24 pct. While this huge alkaline mass is somewhat variable mineralogically, it has a uniform chemical composition. When the iron, mostly in the form of magnetite, is removed during processing, a remarkably uniform finished product is obtained. Geological surveying has disclosed many million tons of nepheline syenite in the Blue Mountain deposit. Diamond drilling in the area where mining is now being carried out indicates a block of about one million tons.

Jan 1, 1947

By Alexander R. Troiano, Eugene P. Klier

Since the very early work on quenched structures, where the products of the martensite transformation had been recognizedl this transformation has provoked much interest and study. Theoretically it was desirable to account for the extreme changes in physical properties resulting from the formation of martensite, as that information might lead to results of practical importance. Desirable information, therefore, was on the kinetics of transformation from austenite to martensite as well as on the physical constitution of the martensite. It has been known for years that certain steels quenched to room temperature will contain persistent austenite as well as martensite. Other important and now well-established features of the martensite reaction are the Progress of the reaction on cooling only and the independence of Ar" with cooling velocities exceeding the critical velocity. These facts have been experimentally determined by various methods and investigators. Notable among the early investigators were Tammann and Scheill and Wever and Engel.2 Unfor- tunately, all investigators did not fully interpret their results, which, coupled with several investigations that yielde. conflicting resultsl caused a state of confusion that was not clarified until quite recently. X-ray investigations of martensite in steels3-6 indicate it to be a supersaturated solid solution of carbon in alpha iron. This supersaturation is evident from the appearance of a body-centered tetragonal structure with the addition of sufficient carbon. The dimensions of this tetragonal structure are a linear function of the carbon content within the limits of accuracy of the determinations. Slight tempering of tetragonal martensite leads to the destructi,, of the tetragonal structure, which is converted to a body-centered cubic strutture. This phenomenon has precipitated a controversy concerning the nature and mechanism of the tempering of martensite The facts in the case have been outlined by Epstein7 and more recently by Antia, Fletcher, and Cohen.8 The significance of Ar" on theoretical grounds is not clear, however, although considerable study has been devoted to its determination. The precise position of Art' aS a function of carbon content was first stated by Greninger and Troiano9 for steels covering a range of approximately 0.7 to 1.8 per cent carbon. The effect of alloying elements on Ar" has recently been the subject matter of investigation by various methods.

Jan 1, 1945

By E. N. Pennebaker

The concept of "unitization" comes from the petroleum industry. Of this, Campbell says: "Unitization is the process whereby the owners of adjoining properties pool their reserves and form a single unit for the operation of the properties. The revenue from operation of this unit is then divided in accordance with the basis established in the unit agreement. "The purpose of such an agreement is to produce the reserves more efficiently and thus to increase the profit to every participant."'

Jan 8, 1973

By C. E. Shoenfelt

There was very little oil activity in Utah in 1938. A few wildcat tests were drilled and the well at Cane Creek, started in 1937, was in active operation, but failed to reach its objective by the close of the year. The Clay Basin field in Daggett County, northeastern Utah, was extended about a mile east by the Mountain Fuel Supply Co. with the completion early in June of No. 3-D Murphy, NW. NW. SW. of sec. 23-3N-24 E. This well had an initial production of 16,000,000 Cu. ft. of gas a day under 2160 Ib. pressure, from Dakota sand at 5918 to 5925 ft. after plugging back from a total depth of 6035 feet. The Clay Basin field, in the few years it has been in operation, has developed into a gas field of major importance. Approximately 1300 acres has now been proved by development. Six wells are on production, five of which were completed in Dakota sand and the sixth in a sand in the Frontier formation. The field was connected to the Salt Lake line

Jan 1, 1939

By C. E. Shoenfelt

There was very little oil activity in Utah in 1938. A few wildcat tests were drilled and the well at Cane Creek, started in 1937, was in active operation, but failed to reach its objective by the close of the year. The Clay Basin field in Daggett County, northeastern Utah, was extended about a mile east by the Mountain Fuel Supply Co. with the completion early in June of No. 3-D Murphy, NW. NW. SW. of sec. 23-3N-24 E. This well had an initial production of 16,000,000 Cu. ft. of gas a day under 2160 Ib. pressure, from Dakota sand at 5918 to 5925 ft. after plugging back from a total depth of 6035 feet. The Clay Basin field, in the few years it has been in operation, has developed into a gas field of major importance. Approximately 1300 acres has now been proved by development. Six wells are on production, five of which were completed in Dakota sand and the sixth in a sand in the Frontier formation. The field was connected to the Salt Lake line

Jan 1, 1939

By J. L. Brimhall, R. A. Huggins

The structure of deformed internally oxidized alloys of siluer- cotztcrining magnesium and copper-containing aluminum in was studied by thin-film transrrzissiotz electron microscopy. With low to moderate amounts of stvain, the deformation structure in t11e dispersion-hardened alloys was found to consist of a high density of dislocations arranged it a random distribution or in a very fine, but poorly defined, cell stucture, depending on the fitness of the dbsbersion and amount of deformation. 112 contrarst, both pure copper and silver show relative1y Large, distinct cell structures. The particular structures in the alloys are believed to result from particles acting as both dislocaliot~ sources and deflector-s. The Inck of a pvorzolrr~ced deformation texture tr~ regiotzs qf' seoere loctll plastic curvature after heavy deformation can also be traced to the formation of clislocntions on many slip systemes and a lack 01 local concentrations of dislocations of predominantly one sign. THE presence of fine dispersions of a second phase has long been known to have a strong influence upon the mechanical properties of solids. Until recently, the influence of particles on the deformation mechanisms has been assumed to be solely that of barriers to dislocations. This is seen in the classic models of edge dislocations being restrained by the particles.1 4 There is, however, considerable evidence that this is not their primary effect, and that the particles can have a large influence on the defect structure generated by plastic deformation. The presence of particles causes changes in the surface topography observed after deformation. In overaged precipitation-hardened materials containing hard, noncoherent precipitates, fine intersecting slip lines are found after deformation of single crystals. indicating the activation of many slip systems. This has been extensively observed in the A1-Cu systen;, both by optical microscopy and replica electron microscopy.'"13 In some of the observations. the slip lines were seen to extend between the particles. Similar observations of extremely fine slip lines or the apparent absence of normal slip lines have also been found in A~-M~."

Jan 1, 1965

By Wayne D. Gould

Cities Service Co.'s Pinto Valley concentrator was designed to eliminate excess capital costs without loss of efficiency. The result is a workable plant with some important innovations. These innovations, the equipment used, and plant processes are outlined. Particular attention is paid to the work efficiency and wear of the six ball mills, the largest wet ball mills made. For experiment purposes, four designs of liners were installed. The effectiveness of each design is discussed.

Jan 1, 1977

By Leo F. Reinartz

This is the fourth and final installment of Leo Reinartz' summation of the steelmaking industry over the first one hundred years. ALTHOUGH basic open-hearth steel has been in the limelight for many years, it has had to share some of its glory with two lesser but nevertheless important rivals, one 50 years old and one a rejuvenated process. Electric steel Electric-steel manufacture began in a humble way in the United States in 1906, when the first heat was tapped from a 3-ton Heroult electric furnace at the Halcomb Steel Co., Syracuse, N. Y. During the intervening years, it has completely eliminated the crucible process. For many years electric melting furnaces were located predominantly in relatively small, nonintegrated plants, making all kinds of high-grade alloy steels. Most of these furnaces, with capacities ranging from 5 to 20 tons, had basic bottoms. During and after World War II, many large basic electric furnaces, some up to 200 tons in capacity, were installed in integrated plants to make commodity steels. There were several reasons for building electric furnaces. Capital investment per annual ton of capacity was low and furnaces could be installed quickly. Since these furnaces used mostly scrap iron in the charge, no extra expensive coke- and blast-furnace capacity had to be added. The perfection of the top-charging design, and the development of large transformers and furnaces, made possible tons per hour as high as from modern 350-ton. open-hearth furnaces. Electric furnaces have high availability and repair costs are low. The process is flexible. Alloy and plain carbon steels of high quality can be made. Where power costs are low, the operating cost can

Jan 1, 1961

By Walter R. Crane

PAGE I. Apparatus and Methods.......... 406 1. The Magnetic Circuit...........406 2. Apparatus Employed in the Traction-Method...... 406 a. The Coils............409 b. The Pole-Pieces..........409 3. Methods of Testing Fields Produced by Different Pole.Pices.. ..409 c. Testing with a Search.Coil........410 d. Testing with Iron-Filings and Glass Tube.. .. .410 4. General Forma of Pole-Pieces.........411 e. Flat Poles............411 f. Conical Poles........... 411 g. Spherical Poles...........411 h. Chisel-Edged (Chamfered) Poles.......412 II. Magnetic Fields...........412 5. Methods of Testinq for Magnetic Permeability...... 421 i. The Rod-Method..........423 j. Method Employed in These Experiments......424 k. Difference in the Results of the Two Methods..... 425 l. The Traction-Method.........427 m. Effect of Loosening the Charge.......430 n Corrections...........432 6. Theory.............433 o. Effect of Varying Weight on Tractive Force..... 434 p. Effect of Varying Pole-Distance.......436 q. Effect of Varying Magnetization.......436 T. Effect of Varying Size.. .......437 a. Summary,........... 441 III. The Relative Magnetic Permeability of Various Minerals,. 443 The form and strength of magnetic fields have attracted much attention. especially in connection with the designing of dynamo-electric machinery—an art which has been revolution-

Jan 1, 1902

By R. F. Davis

The evaluation and selection of coals for producing metallurgical coke is indeed a complex process simply because coal is a complex and variable substance which is sensitive to how it is treated from the time it is mined until it is transformed into coke. A review of some of the more common evaluation tests made on coal and how the test results are applied in commercial practice should be of interest. Parameters used to select coking coal blends for wet and preheated charges should also be of interest.

Jan 1, 1982

By Morris Muskat

ALTHOUGH the problem of well spacing is one of the most important involved in the production of oil, it must be considered at the present time as still subject to further development. The published literature on this question is so voluminous that we cannot enter here into a review of it, except to refer to the recent papers by L. L. Foley1 and E. A. Stephen-son,2 where other references are cited. However, a decisive and conclu-sive answer to the problem of well spacing in any general form does not seem to have been developed. And while we shall be unable to present the desired solution in the present paper, it is nevertheless felt that the material to be given here not only provides the physical ground work for the ultimate solution, but shows qualitatively the essential factors that enter the well-spacing problem. Field studies of the well-spacing problem, in which the ultimate recoveries from different fields with different well spacings have been compared, have generally suffered from the lack of knowledge as to the similarity of the inherent characteristics of the producing reservoirs being compared, such as the sand volumes, the sand porosities, the sand permeabilities, the original reservoir pressures, the presence or absence of gas caps, the presence or absence of effective water drives, and the economic limits of production rates at which the various fields were considered to have yielded their ultimate recoveries. Certainly no one who is evaluating originally the economic significance of any oil reservoir would deliberately ignore these phases of the problem. And it is equally certain that no one would reasonably expect the ultimate recoveries from two reservoirs, even with the same well spacing, to be identical regardless of these other factors. More reliable results might be expected from comparisons of the recoveries obtained from different leases with different well spacings, but producing from the same reservoir sand. Unfortunately, however, even conclusions for such studies may be subject to serious errors. The reason simply is that however much one may insist that an operator is entitled only to the oil immediately underneath his surface acreage he will nevertheless drain the surrounding properties as long as his reservoir

Jan 1, 1939

By Morris Muskat

Although the problem of well spacing is one of the most important involved in the production of oil, it must be considered at the present time as still subject to further development. The published literature on this question is so voluminous that we cannot enter here into a review of it, except to refer to the recent papers by L. L. Foleyl and E. A. Stephen-son,2 where other references are cited. However, a decisive and conclusive answer to the problem of well spacing in any general form does not seem to have been developed. And while we shall be unable to present the desired solution in the present paper, it is nevertheless felt that the material to be given here not only provides the physical ground work for the ultimate solution, but shows qualitatively the essential factors that enter the well-spacing problem. Field studies of the well-spacing problem, in which the ultimate recoveries from different fields with different well spacings have been compared, have generally suffered from the lack of knowledge as to the similarity of the inherent characteristics of the producing reservoirs being compared, such as the sand volumes, the sand porosities, the sand permeabilities, the original reservoir pressures, the presence or absence of gas caps, the presence or absence of effective water drives, and the economic limits of production rates at which the various fields were considered to have yielded their ultimate recoveries. Certainly no one who is evaluating originally the economic significance of any oil reservoir would deliberately ignore these phases of the problem. And it is equally certain that no one would reasonably expect the ultimate recoveries from two reservoirs, even with the same well spacing, to be identical regardless of these other factors. More reliable results might be expected from comparisons of the recoveries obtained from different leases with different well spacings, but producing from the same reservoir sand. Unfortunately, however, even conclusions for such studies may be subject to serious errors. The reason simply is that however much one may insist that an operator is entitled only to the oil immediately underneath his surface acreage he will nevertheless drain the surrounding properties as long as his reservoir

Jan 1, 1940

By Morris Muskat

Although the problem of well spacing is one of the most important involved in the production of oil, it must be considered at the present time as still subject to further development. The published literature on this question is so voluminous that we cannot enter here into a review of it, except to refer to the recent papers by L. L. Foleyl and E. A. Stephen-son,2 where other references are cited. However, a decisive and conclusive answer to the problem of well spacing in any general form does not seem to have been developed. And while we shall be unable to present the desired solution in the present paper, it is nevertheless felt that the material to be given here not only provides the physical ground work for the ultimate solution, but shows qualitatively the essential factors that enter the well-spacing problem. Field studies of the well-spacing problem, in which the ultimate recoveries from different fields with different well spacings have been compared, have generally suffered from the lack of knowledge as to the similarity of the inherent characteristics of the producing reservoirs being compared, such as the sand volumes, the sand porosities, the sand permeabilities, the original reservoir pressures, the presence or absence of gas caps, the presence or absence of effective water drives, and the economic limits of production rates at which the various fields were considered to have yielded their ultimate recoveries. Certainly no one who is evaluating originally the economic significance of any oil reservoir would deliberately ignore these phases of the problem. And it is equally certain that no one would reasonably expect the ultimate recoveries from two reservoirs, even with the same well spacing, to be identical regardless of these other factors. More reliable results might be expected from comparisons of the recoveries obtained from different leases with different well spacings, but producing from the same reservoir sand. Unfortunately, however, even conclusions for such studies may be subject to serious errors. The reason simply is that however much one may insist that an operator is entitled only to the oil immediately underneath his surface acreage he will nevertheless drain the surrounding properties as long as his reservoir

Jan 1, 1940

By F. Keller, A. H. Geisler

Some of the important changes that take place in the structure of aluminum alloys are largely submicroscopic in character. This is especially true of the changes that accompany age-hardening and recrystallization. Although improved metallographic practices have been helpful in indicating some of these changes indirectly, results are limited by the resolving power of optical microscope lenses. The electron microscope, however, provides a new and important means for investigating the fine structure of metals in a range not possible heretofore. It is anticipated that this microscope will yield new and useful information to metallurgists when suitable techniques are developed to utilize its very high resolving power. Several unique methods have been devised to permit the examination of the structure of opaque samples by the electron microscope. These are all based on the principle of producing a very thin film that represents the prepared surface of the opaque metal sample, which can be examined in the transmission microscope; however, the available methods fall into three categories, depending on the manner in which the film is obtained. With the oxide-film method developed by Mahl3-17 a very thin surface layer of the metallographic sample is converted into oxide by a thermal, chemical or anodic treatment. After removal from the metal sample by one of the special techniques described by Evans,19 this oxide film is examined in the electron microscope, and is found to portray the structure of the original metal surface. Films formed on aluminum,8,17 nickel,7 iron 3,8,9 and a nickel-beryllium alloy" by heating; films formed on iron 8.9 by chemical action; and films formed on aluminum3-16 by anodic oxidation, have been examined. The other two are more recent methods developed principally in this country; they consist in making the thin film in the form of a mold or replica of the surface contour of an etched sample. With the negative replica method the thin film is made directly on the sample; with the positive replica method it is made on a negative reproduction of the sample. With both methods, variations in the contour of the metal sample, caused mainly by etching, produce variations in the thickness of the surface replica. Because of the direct dependence of the amount of scattering of the illuminating electrons upon the thickness of the film penetrated, only the variations in thickness of the replica are responsible for tones in the electron image. Negative replicas are made by forming a thin film of some suitable material directly on the polished and etched metal sample, and derive their name from the fact that after removal from the sample they have the high and low points in the sample reversed, as shown in Fig. I. Nega-

Jan 1, 1944

By E. Marburg

Most ingots complete solidification vertically rather than transversely. This conclusion is based on complete solidification patterns of big-end-up and big-end-down ingots developed from dumped and split ingots. New mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon adequate width of vertical core. A LTHOUGH it has long been recognized that the A internal soundness of ingots is principally been recognizedthatthedependent on the process of solidification, knowledge of this process is still only fragmentary. The mechanisms causing the several types of segregation in ingots, which mechanisms are necessarily related to the solidification process, are not well understood. In absence of a better conception of the solidification process, it seems hardly surprising that mold design varies widely. Guiding principles for mold design are needed. At stake in the improvement of ingot quality are not only improved properties of steel but also appreciably higher yields of sound steel, which would considerably decrease manufacturing costs. In the present study, following a general description of the several types of segregation in ingots, Fig. 1, complete solidification patterns of a big-endup and a big-end-down ingot, including the zones of accelerated solidification, have been reconstructed. In both ingots, a core of vertical solidification extends from the base cone to the hot-top junction. Based on the finding that ingots complete solidification vertically rather than transversely, as has been previously assumed, new mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon the width of the vertical core, which in turn depends principally upon the width to height (w/h) ratio of the ingot. Solidification patterns of ingots are of three general types: 1—those in which vertical solidification does not reach the top, 2—those in which vertical solidification just reaches the top of the ingot, and 3—those in which vertical solidification reaches the top some time before transverse solidification would reach the middle of the ingot, so that a vertical core of definite width at the top of the ingot is developed. Axial defects vary characteristically with the solidification pattern. Examples of ingots of each type are presented. Dumped ingot data reported by Nelson' have been used in developing families of curves of transverse and vertical solidification, and in deriving the effect of the w/h ratio upon the solidification pattern. Photographs of many ingots split at Homestead and at Duquesne Works, United States Steel CO., as well as those published by the British Iron and Steel Institute,' have been studied and analyzed. In the interest of brevity, only typical ingots of each type or classification from the above sources have been reproduced. Segregation in Ingots Segregation in ingots falls into three principal classifications: 1—lamellar segregation, as revealed in sulphur prints (Figs. 2 and 3); 2—zone segregation, or broad variations in composition; and 3— interdendritic, or microsegregation. The last class, of minor importance, is not considered here. When liquid metal cools, according to the theory of differential or selective solidification,2 metal of relatively high purity selectively solidifies first. Liquid segregates (principally carbon, phosphorus,

Jan 1, 1954

By Frank E. Caropreso, William P. Badger

A hydrogen peroxide precipitate process has been adopted by Atlas Minerals for the recovery of uranium oxides from sodium chloride strip solutions. Adoption of the process was based on laboratory and plant tests comparing hydrogen peroxide with other precipitants. Plant operation has demonstrated that the hydrogen peroxide process consistently yields uranium concentrates of high purity and barrens of low uranium content. Increased U3O8 concentration in the product, reduced levels of impurities which incur penalties, and higher product density have produced economic advantages.

Jan 1, 1974