Search Documents

By Robert M. Lewis

Can wet-ground mica be produced from mica schist ores, and if so, would its properties be comparable with products now on the market? This was the problem which prompted the development of a flowsheet for the beneficiation of mica schist. The fine-ground mica industry relies on weathered pegmatites and alaskite ores as sources of raw material. The mica concentrates obtained from these ores are relatively clean and require moderate beneficiation to meet color and bulk-density specifications. Mica obtained from mica schist is iron-stained and decrepitated and requires additional beneficiation to produce a wet-ground mica product. Despite these adversities, there are several advantages to be gained by mining and processing mica schist ores. The mica content of these ores is considerably higher than that of the pegmatites and alaskite ores now being mined, often containing in excess of 40% mica. This higher-grade mica feed should promote a lower mining and milling cost. The mica schist ores with their higher mica content would mean less tailings to handle; however, there would have to be a means for disposing of acid and sulfate wastes. A flowsheet was developed whereby mica could be recovered from mica schist ores and beneficiated in a way that would result in a high-quality end product.' The essential phase of the process involves using reducing reagents to increase the magnetic susceptibility of iron contaminants which then can be removed with a magnetic separator. General Treatment Procedure The mica is floated by either of two methods, an amine float in an acid circuit' or the U.S. Bureau of Mines (USBM) amine-fatty acid float in an alkaline circuit' The flotation mica is ground in a pebble mill to liberate contaminated particles and expose iron-stained surfaces. The concentrate is then conditioned with a reducing reagent and passed through a Frantz Ferrofilter for the removal of magnetic material. The nonmagnetic product is acid-leached to further reduce the iron contamination. The leached material is then ground to product size and checked for specifications. Discussion of Flowsheet and Its Development Flotation: The mica is concentrated by flotation using either of two methods: an amine float in an acid circuit, or the USBM amine-fatty acid float in an alkaline circuit.' The writer does not wish to elaborate on the relative merits of the two flotation procedures; however, after investigating ores from various localities, it was felt that the amine float in an acid circuit was more consistent when using a standard procedure. Iron Reduction and Magnetic Separation: This phase of the flowsheet may be considered the key to the process. It was developed when it became apparent that hot acid leaching had just about reached its maximum effective¬ness for color improvement. S. C. Sun and William Hirsh in "Hydrochloric Acid Leaching of Iron From Pennsylvania Aluminous Clays,"` reported iron extraction for -20-mesh minerals of 82.20% for hematite and only 33.46% for magnetite. The test procedure employs a 19% hydrochloric acid solution, 104°C temperature, and 10% solids. It was felt that magnetic removal of some of the iron contaminants before leaching therefore would be advantageous. Since the iron minerals present as contaminants vary in magnetic susceptibility, it was decided to experiment with reducing reagents as a means of influencing their magnetic properties. Zinc hydrosulfite or sodium hydrosulfite were the reagents used throughout the tests. The procedure developed consists of conditioning the mica concentrate in a closed container at approximately 5% solids with a reducing reagent. Approximately 10.0 lb of zinc hydrosulfite per ton of mica concentrate is used. The ferric iron is reduced to the ferrous state (magnetic) and oxidation is retarded by isolation from the atmosphere in a closed container. After the desired conditioning time has elapsed, the material is passed through a Frantz Ferrofilter where the magnetic particles are retained and discarded as

Jan 1, 1972

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Experienced mining. engineer, Columbia School of Mines graduate, practical experience in drifting, shaft sinking and development work, also in mining, operating and equipping iron, copper, and zinc properties. Married, age 32, available at once. Open for position as superintendent or assistant. No. 462. Member, age 33, married, desires position as mining engineer or engineering executive.- Twelve years experience as mining engineer, geologist, and chief engineer of iron and copper properties. Experience in United States, Mexico and South America. Fluent Spanish. Technical graduate. Minimum salary $3000. No. 466. Member, technical, general superintendent and mill superintendent: Well experienced in latest methods of ore reduction, especially on copper and complex ores. Draft exempt. Not less than $250 per month considered. No. 469. Consulting mining geologist, member of Geological Society of America and A. I. M. E., Professor of Geology and Mineralogy, Lawrence College, desires temporary position during summer in mine surveying, mining methods, expert mine valuation or any exploration work or mine development. Applicant has had nearly three years' experience in gold mining in Mexico and many years professional mine examination work in all regions of Western U. S. Terms reasonable. No. 470. Member, mining engineer, age 46, desires engagement as manager of mining properties, coal or metal mines. Education and 25 years experience in all branches of mining. Have been successful with labor in the management of large properties. No. 471.

Jan 8, 1918

By John V. Beall

Given: One large, but dated open-pit copper mine and processing plants, down about one third in production capacity in decade because of declining ore grade. Solve for: Restoration of former peak capacity without further losses during period of reconstruction. That is the problem that Kennecott's Utah Cop- per Division began solving in 1963. Most of the work went to a task force of engineers, several of whom were plucked out of line jobs and assigned to the so-called "Expansion Project" for the duration. There was no doubt from the beginning that effective cooperation between Expansion Project engineers and operators was critical to success, and personnel was chosen accordingly. This foresight paid off. The Expansion Project is all but complete, and the Utah Copper Division is returning to its rated capacity of 300,000 tons per year of copper metal.

Jan 6, 1967

By Jay A. Carpenter

IN six years the construction of Hoover Dam and the power plants probably will have reached the operating stage and this vast new source of power will then be continuously available for industry. The height of the darn will be 580 ft. and the average annual flow of the Colorado River is calculated at approximately 24,000 cu.ft. per sec. If this full head and average flow can be maintained the year round, about one million horsepower will be generated. The U. S. Reclamation engineers, taking into consideration the probable range in flow and head, have set the figure for power contracts at 660,000 firm horsepower, which can be assured at all times of the year. During the months of heavy run-off of water from the Colorado River Basin the power plants should be able to generate the full 1,000,000 hp. capacity of the power plants, so there will be 340,000 excess or secondary horsepower. The cost of firm power at the switchboard will be close to 2.15 mills per kw.-hr., equal to $14.05 per hp.-yr., and the cost of the secondary or off-peak power will be close to 0.8 mills per kw.-hr., or $5.22 per hp.-yr. In no place in the country can such cheap power be obtained today. The electrochemical industry is in a state of flux because the power costs from its old sources have increased so much (to $30 per hp.-yr. at Niagara) that the industries have had to seek new sources, so they have gone to Canada and Norway and built new plants.

Jan 1, 1932

By Joseph Singewald

INTRODUCTION FOR a number of years Russia, India and Brazil have outranked .all other countries as producers of manganese ores. During the 5 years immediately preceding the European war, the average annual production of Russia was 844,000, of India 694,000 and of Brazil 200,000 long tons. Since the outbreak of the war there has been a considerable falling off in the Russian and Indian production, particularly in the former, whereas the production of Brazilian ores has been greatly increased, amounting in 1914 to over 250,000 tons and in 1915 to nearly 350,000, with conditions favorable for a still larger production in 1916. Manganese is one of the few industrially important metals that are not produced in the United States in quantity commensurate with our needs, so that we have been compelled to import annually about 300,000 tons, having a value of over $2,000,000, and these ores have been obtained from the three countries mentioned above. Their rank as contributors to our imports of manganese ores was India, Russia, Brazil; and in 1913, Brazil contributed only one-fifth. During the past 2 years Brazil has furnished rapidly increasing quantities to this country, and, with the falling off of imports from India and Russia, has become our principal foreign source. In 1914, Brazil furnished two-fifths of the imports and more than India or Russia, and in 1915 over nine-tenths. The manganese ores of Brazil are consequently of more than usual interest to us at this time.

Jan 10, 1916

By O. O. Laudig

It is a well-established fact that some ores do not reduce as readily in the furnace as others, thus seriously affecting out-put, and consequently, cost of product. With the object of obtain ing some information upon this subject, the following experi ments were made in the laboratory of the Buffalo Furnace Company. Efforts were made to obtain, as nearly as possible, represent ative ores from some of the most important mining districts in the United States. The ores received were from the Mesabi, Marquette, Gogebic, Menominee and Vermilion ranges of the Lake Superior district and from Southwest Virginia. Requests

Jan 1, 1897

By J. P. Carson

THE Croton water-shed furnishes the source and storage of watersupply to both the old and the new aqueduct. The Croton river rises in the southern part of Dutchess county, about 68 miles from the lower end of New York city. Its three main branches, called the East, Middle and West branches, flow southward across Putnam county, joining, near its southern boundary, to form the Croton, which continues thence in a general southwest direction across Westchester county to the Hudson river at Croton Point, about 35 miles north of the city. The water-shed above the proposed site of the Quaker Bridge dam extends about 33 miles north and south, with an average width of 11 miles, making in all about 362 square miles, from which, by complete storage, an average daily supply of 250,000,000 gallons may be collected—sufficient for the needs of the city, probably, for the next fifteen years. The water-shed above the Croton dam is 23 square miles smaller, and furnishes the present daily supply of 100,000,000 gallons. By referring to the map it will be seen that the shortest approximately straight line between the proposed site of Quaker Bridge

Jan 1, 1891

By John C. Sawyer

A brief review is given to show that catastrophic oxidation of stainless steel in the presence of lead oxide is similar in many respects to catastrophic oxidation as caused by MoO3 and V2O5, Experimental data are presented to show that lead oxide accelerates the normal oxidation process of stainless steel by chemically altering the normally protective oxide film formed on the base metal. Data are given to show that similar reactions occur during oxidation of stainless steel in the presence of MOO3,and V2O5. THE mechanism by which pure metals oxidize at high temperatures has been the subject of intensive research for many years and much has been accomplished towards understanding the processes involved. The mechanisms by which alloys oxidize have also been investigated, but due partly to the fewer number of investigations and partly to the complexity of the oxide systems present, available knowledge is not as extensive as with pure metals. When oxidation processes are further complicated by atmospheres contaminated with sulfide, halide, or oxide vapors, the knowledge of fundamentals becomes meager or altogether lacking. Thus, it is not surprising to find that the catastrophic oxidation of stainless steels in metal oxide vapors of MOO, and V2O5 is not a well understood phenomenon despite the fact that a number of investigations have been undertaken. The literature in dealing with the subject of catastrophic oxidation is primarily concerned with the effects of MOO3 and V2O5, but does mention that other metal oxide vapors, one of which is lead oxide, appear to promote a similar type of accelerated oxidation. While this latter effect is virtually unknown, the deleterious effect of lead oxide is of considerable commercial importance, as it is believed to be one of the fundamental reasons for exhaust-valve failure in gasoline engines. For this reason studies have been in progress for many years attempting to better understand the mechanism involved. Modern exhaust-valve alloys"2containing 20 to 25 pct Cr plus nickel and/or manganese are in effect high-grade austenitic stainless steels exhibiting ex- cellent oxidation resistance in air at exhaust valve operating temperatures of 1100° to 1700°F; yet these same alloys are prone to corrode during engine service because of the conditions attending their operation. These conditions are such that the valves become coated with deposits of complex lead compounds mainly derived from gasoline additives of tetraethyllead, ethylene dibromide, and ethylene dichloride. Literature searches3-7 and discussions with various investigators show that considerable difference of opinion exists as to the nature of the lead-bearing deposits found on the surface of exhaust valves and the atmospheres to which they are subjected; yet, all seem to generally agree that corrosion, a gradual transformation of alloy to nonmetallic products of corrosion, is a consequence of the presence of lead compounds. This majority opinion seems to be substantiated by laboratory engine tests which show that corrosion does not occur to any appreciable extent when lead-free fuels are used. The first observations of catastrophic oxidation reported in the literature were probably made by pfeil,8 but it was Leslie and Fontana9 who undertook the first detailed study of the phenomenon. Their work was chiefly centered on the acceleration of oxidation which took place when stainless steels containing more than 3 pct Mo were heated in air with restricted circulation. These investigators reported that the presence of other oxides near the surface would further accelerate the rapid oxidation which occurred. While they recognized that the effect was attributable to the presence of molybdenum, it was Rathenau and Meijering" who emphasized the fact that the presence of molybdenum in the alloy was incidental to the presence of MOO3 vapor in the atmosphere surrounding the specimens. Evans,11 as well as Cunningham and Brasunas 12 studied similar

Jan 1, 1962

By A. J. Hendron, D. U. Deere, F. D. Patton, E. J. Cording

In the design of structures founded in the near-surface rock, a distinction may be made between those problems that are related to the strength of the rock mass, and those that are related primarily to the compressibility of the rock mass. The mining engineer deals almost exclusively with problems involving strength in the design of open-pit slopes and underground openings. The civil engineer is similarly concerned with strength problems in the design of vehicular and water tunnels; underground power plants; cut slopes in rock for highways, canals, and spillways; and in the study of the sliding resistance of the foundations of gravity dams and the abutments of arch dams. Moreover, the civil engineer encounters problems in which the compressibility of the rock becomes the key element in the design. These problems include settlement of heavy structures supported on rock, deformation of the abutments of arch dams, and deflection of pressure tunnel linings. The design problems listed above are still solved largely on the basis of experience and rule-of-thumb. However, recent developments in rock mechanics give promise of providing more realistic approaches to certain aspects of the design. This paper, presents some of the more important recent developments which contribute to an understanding of rock behavior and which aid in design of rock structures. Typically, four steps are involved in the design of a structure, whether it be a machine element, a structural member of a building, or a structure in rock. These steps are listed below:

Jan 1, 1967

By S. C. Hollister

An evaluation of the function of the engineer, so that means whereby education can best serve his needs can be adopted. THERE has been a steady increase in specialized branches of engineering during recent years. Some of these are simply specializations in the function of engineering, such as welding engineering, tool and die engineering, petroleum engineering, and refining engineering. Others are associated more closely with the basic sciences, as for example, geological engineering or engineering physics. Still others tend toward the border line of business, such as administrative engineering or general engineering.

Jan 1, 1950

By S. Roath, F. Paul, D. Melville

Several attempts have been made over the past 40 years to separate red blood cells from whole blood using a magnet. This has been achieved by the authors by using a high gradient magnetic field and " carrying " the red cells in a suitable reducing agent - the deoxyhaemoglobin so produced has 4 unpaired electrons per atom giving appreciable paramagnetic moment as opposed to the usual oxygenated form which is diamagnetic. Red blood cells so separated appear to be undamaged and can be reinjected into a donor animal where their survival is shown to be normal using an isotope tagging technique. Studies on function of the white blood cells and blood platelets also indicate that they are functionally unchanged by separation process.

Jan 1, 1980

By D. H. Newland

Certain observations from the field and laboratory suggest the need for recasting some of our ideas about gypsum as a rock-forming mineral and in relation to supplies for industrial use. Until about 25 years ago, the use of gypsum was confined almost entirely to agriculture. During the past quarter century, though, its usefulness has been greatly developed, particularly in the building trades, which now absorb most of the gypsum produced. In 1919, according to the U. S. Geological Survey, the output of crude gypsum was 2,240,163 tons, a gain of 912 per cent. in 25 years. About one-half of this production was mined in New York, Ohio, and Michigan, where the proved supplies can hardly be regarded as over-large when viewed in relation to the rapid expansion of industrial requirements. The occurrence of gypsum in the United States is treated by R. W. Stone and others.' The deposits of Canada are described by L. H. Cole. Several states, including Kansas, Oklahoma, Iowa, Michigan,and New York, have made special surveys of their gypsum deposits, but the reports, as a rule, refer to conditions as they existed from 15 to 20 years ago. Association of Gypsum and Anhydrite The two calcium sulfate compounds, gypsum (CaSO4.2H2O) and anhydrite (CaS04), are the more stable forms of a series which includes at least two other members, so-called half-hydrate (CaSO4.1/2H20) and soluble anhydrite (CaS04). Each of the latter readily takes up water to recrystallize as gypsum and consequently is incapable of existence under ordinary geological conditions; also each can be prepared from gypsum by the application of heat within certain temperatures, the process on which is based the manufacture of commercial plasters. If the temperature limitations are not observed, the result of the calcination process will be insoluble anhydrite which, compared with the soluble form, takes up water very slowly so as to be of no practical use, although actually it is soluble and in time is convertible into gypsum like the other forms.

Jan 1, 1922

By Ernest F. Burchard

A reconnaissance of the chrome and manganesel ore deposits of Cuba was made in the spring of 1918 by Albert Burch, representative of the U. S. Bureau of Mines, and the writer, representing the U. S. Geological Survey. The object of the study was to obtain authentic information for use of the United States Government as to the location, character, size, and availability of the Cuban deposits of the ores of these important steel-alloy metals. The Cuban Government courteously detailed Sr. E. I. Montoulieu, a mining engineer connected with the Treasury Department, to act as escort and associate throughout the work on the Island. Mr. George A. Wright, of Baracoa, Cuba, a minirng engineer especially familiar with the chromite deposits of Oriente Province, was a member of the party from Feb. 25 to Mar. 20. It was possible to visit most of the chrome-ore deposits that seemed to be of promise, but there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Furthermore, no attempt was made to examine the extensive chromiferous iron-ore deposits of the Mayari, Moa, and Cubitas districts, as these deposits cannot be regarded as sources of chromium except indirectly. At the close of the field work the essential data concerning the quantity and quality of ore probably available for shipment during 1918 and 1919, in the event of the continuation of the European war, and of the tonnage of ore in reserve, were furnished to such Government bureaus as were interested, including the Shipping Board and the War lndustries Board, and as soon as chemical analyses of the chrome ores could be obtained, a press bulletin on the subject was published by the Geological Survey. In the present paper the engineering data and tonnage estimates contained in the unpublished notes of Mr. Burch have been freely used, and their helpfulness is hereby gratefully acknowledged. Many thanks are due Senor Montoulieu and Mr. Wright for their valuable work in the field; to the officials of the Spanish American Iron Co. and of the various other companies; and to individuals holding chromite claims, for courteously facilitating the work of the party.

Jan 1, 1920

By H. R. Hanley

IN AS MUCH as the interesting changes in the economics of the zinc industry are covered nowhere else in this issue, and they are related to technological progress in the metallurgy of zinc, some reference to prices and production will first be made. The latter part of 1939 is outstanding in the large war demand for metals including zinc, whereas in the first eight months the demand for zinc was subnormal. The cause of the rapid in- crease in demand was the European war and hence the future is problematical. When the year began zinc was in the doldrums, with low prices, and continued thus until August when an advance in price started, reaching 6.5. per pound early in October. (Prime Western, St. Louis.) Rapid changes in the price of any metal are viewed adversely by the metal industry. The persistent low price for zinc of 4 to 49512 for about two years curtailed production and in one instance closed one large plant for a brief period.

Jan 1, 1940

By W. A. McCurdy, Joseph W. Leonard, T. S. Spicer

INTRODUCTION by T. S. SPICER and J. W. LEONARD Utilization from the Point of View of the Preparation Engineer The primary interest of the coal preparation engineer is process design, operation and maintenance to produce an acceptable product which can be sold at the greatest possible profit. Because of these interests, attention to the unrealized potential value of coal is sometimes neglected. The intent of this chapter is to alert the preparation engineer to the utilization possibilities of both the product as well as the tributary coal flow moving through a modem coal preparation plant. Thus, coal types having similar physical and chemical properties tend to become increasingly concentrated according to size, specific gravity and/or surface chemistry. The basis for any unrealized potential derives directly from the coal seam itself. Most coal seams consist of coal bands and benches which are sandwiched together in layers and which visually differ from each other by physical structure and luster. Randomly selected physical and chemical ranges determined from layers of coal in a single seam can easily differ by as much as 30 Hardgrove grindability indices, 0.30 of a specific gravity point, 20 percentage points of ash, six percentage points of dry volatile matter and 10 percentage points of total sulfur.1 Similar wide variations exist for calorific value, seam moisture content and undoubtedly, for any other conceivable coal test parameter which might be used for comparative purposes. These observations all point to the long established fact that coal is not homogeneous as conventional analytical methods might tend to indicate, but is instead a highly heterogeneous substance. Since both coal and associated minerals entering a preparation plant are highly heterogeneous, a multi-product potential beginning with certain flotation cell concentrates and ending with plant refuse may exist. Such a potential can and to a limited extent is achieved at some operations by drawing off coal according to size, specific gravity and/or surface chemistry differences from individual coal cleaning processes. Such a sequenced draw-off of coal of increasing ash increments could yield, among other products, chemical coals, coking coals, coals for pulverized fuel boilers, cyclone boiler coals, coals for cement plants, limestone, shale and clay. Basis for Coal Evaluation and Selection Despite the known heterogeneity of coal, the final analysis of a given coal product is customarily reported as a single average since coal has always

Jan 1, 1968

By W. C. Hayes

The site selected for the United States prototype pumped storage project of Union Electric CO. was Proffit Mountain, five miles from Taum Sauk, the highest point in Missouri. Factors influencing final location were: high local relief; satisfactory rock type and structure; and an economic location in respect to existing transmission systems. The upper reservoir was constructed by excavating rhyolite porphyry from the crest of Proffit Mountain and constructing a rock fill dike encircling the area to form a 4350-acre foot reservoir. A 6564-ft tunnel connects the upper reservoir with the generating and pumping facilities. A concrete gravity dam on the East Fork of the Black River forms the 6350-acre foot lower reservoir. Precambrian rhyolite porphyry forms the crest of Proffit Mountain and the floor of the upper reservoir. The tunnel was excavated in rhyolite prophpy, granite porphyry, dolomite, shales and conglomerate. Abutments and the foundation of the gravity dam are in rhyolite porphyry, and much of the valley floor of the lower reservoir is underlain by dolomite and shale. Core drilling provided data on soundness of rock type, structure, depth of weathered zone and potential water loss in the fractured igneous rocks. After a six-year study of pumped storage and cost comparison with alternate stream generating units, the Taum Sauk pumped storage project was authorized by Union Electric Co. on Dec. 11, 1959.' The site selected is located in the St. Francois Mountains of southeast Missouri approximately 90 miles south of St. Louis (Fig. 1). The lower reservoir was provided by damming the East Fork of the Black River, a small tributary of the Black River with a minimum flow of about 1 sec ft. Construction of the upper reservoir was effected by quarrying the crest of Proffit Mountain - five miles from Taum Sauk Mountain, the highest point in Missouri — to provide material for a rock fill dike surrounding the quarried area. This provided a 55-acre mountain top lake with a water depth of 92 ft (Fig. 2). A vertical shaft and tunnel connect the upper and lower reservoirs through the two reversible pump-turbine motor-generator units operating under 800 ft of hydraulic head (Fig. 3). The output rating of the plant is 350,000 kw with daytime generation of about 2.2 million kw-hr under normal use. Night pumping will replenish water to the upper reservoir in about 91/2 hours3. The automatic operation is remotely controlled from the Osage plant and from the dispatchers office in St. Louis. GENERAL GEOLOGY Mountains of the St. Francois area consist of Precambrian granites, granite porphyries, extrusive fel-sites and basic dikes. Basal conglomerates overlain by Upper Cambrian Bonneterre dolomites and shales onlap the exhumed Precambrian knobs and hills and are exposed in the narrow valleys. Cambrian and Ordovician residuum as much as 200 ft thick is present on the slopes of many hills. Proffit Mountain consists of rhyolite porphyry and granite porphyry. All excavation for the upper reservoir was in rhyolite porphyry, and the same rock is present under the Bonneterre at the plant site and under alluvium at the lower reservoir dam site. The region has been dissected to the stage of early maturity with only small upland flats remaining. Considerable local relief (a requisite for the project) approaches 1000 ft. Streams flowing across the Precambrian ridges have formed restricted narrows, termed shut-ins. A shut-in approximately two miles downstream from the plant site provides an excellent site for the lower reservoir dam. TEST BORINGS Preliminary to final approval of the project, 12 test borings were made to determine subsurface geologic conditions (Fig. 2). Drill hole No. 12 at the lower reservoir dam site showed 20 ft of alluvium over solid rhyolite porphyry. Drill holes No. 1, 2 and 3 were drilled in the tail race area to depths of 66 ft, 75 ft and 95 ft respectively, and all bottomed in Bonneterre. Drill hole No. 4 at the plant site provided NX core to a total depth of 98 ft in Bonneterre. Drill

Jan 1, 1965

By George W. Bain

Methods of mining building stone of any sort are planned to produce as few fractures as possible, and present a strong contrast to methods of mining metallic ores, which must be crushed eventually and have fractures produced in as great profusion as possible. Shocks transmitted to a stone invariably make it more porous and more permeable and reduce its effective life, therefore methods of mining building stone involve as This building illustrates the fine detail of workmanship, unprotected sharp corners and thin edges, and tall narrow columns characteristic of marble structures. These features require exceedingly coherent stone, and preservation of these features for decades or centuries demands many special quarrying precautions to keep absorption to 0.14 per cent or less, a detail not essential to stone for coarser architectural types. few shocks as possible. This is singularly true for marble because marble structures are intended to have long life, greater delicacy of line, more gracefulness and fineness of sculpture than those made from any other structural material (Fig. 1). So that delicate lines may remain in almost perfect preservation for decades, or even centuries, it is important

Jan 1, 1938

By George W. Bain

Methods of mining building stone of any sort are planned to produce as few fractures as possible, and present a strong contrast to methods of mining metallic ores, which must be crushed eventually and have fractures produced in as great profusion as possible. Shocks transmitted to a stone invariably make it more porous and more permeable and reduce its effective life, therefore methods of mining building stone involve as This building illustrates the fine detail of workmanship, unprotected sharp corners and thin edges, and tall narrow columns characteristic of marble structures. These features require exceedingly coherent stone, and preservation of these features for decades or centuries demands many special quarrying precautions to keep absorption to 0.14 per cent or less, a detail not essential to stone for coarser architectural types. few shocks as possible. This is singularly true for marble because marble structures are intended to have long life, greater delicacy of line, more gracefulness and fineness of sculpture than those made from any other structural material (Fig. 1). So that delicate lines may remain in almost perfect preservation for decades, or even centuries, it is important

Jan 1, 1938

By John R. Dyni

Colorado nahcolite deposits, estimated at 29 Gt, formed in an asymmetric permanent-lake basin whose waters were rich in algae and sulfate-reducing bacteria. Nahcolite (NaHCO3) occurs in oil shale of the Green River Formation (Eocene) as aggregates (62%), disseminated crystals (24%), and impure beds (13%). Because much of the nahcolite is nonbedded, it will be mined with oil shale and can be concentrated to marketable grade by crushing and screening. Impurities in nahcolite are kerogen, quartz, pyrite, and carbonate minerals. A promising new market for nahcolite is in the process of removal of sulfur dioxide from industrial stack gases. When heated, nahcolite reacts with sulfur dioxide to form sodium sulfate. Differences in thermally induced microporosity may explain why nahcolite is more reactive than trona, a Possible competitor with nahcolite for SO2 removal. Limited production of nahcolite at one or possibly two localities is expected in the next several years, but large-scale production is probably at least 10 years away.

Jan 1, 1982

The Institute is custodian of funds for support of numerous gold medals and prizes and has representatives on boards awarding still others. Details regarding the Institute Awards are given below. The Institute is represented on the boards of the John Fritz Medal, the Hoover Medal and the Washington Award, in connection with the three national societies of Civil, Mechanical and Electrical engineering; and, also, in the case of the Washington Award, with the Western Society of Engineers. Robert W. Hunt Medal and Prize THE partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes: first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the subcommittee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A subcommittee of three to five, including the Chairman of the Iron and Steel Division, shall be appointed by the Iron and Steel Division annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October meeting, and the award shall be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of .the Institute. 5. The recipient of the award shall be designated "The Hunt Medalist." Awards of the medal have been made as follows: 1920—-Robert Woolston Hunt. 192G—John A. Mathews. 1926—Charles Lewis Kinney, Jr. 1929—Edgar Collins Bain. 193G—James Aston. Awards of the prize have been made as follows: 1928—C. H. Herty, Jr. 1929—William E. Griffiths.

Jan 1, 1930