Search Documents

By F. G. Miller

The washabilities of typical bituminous coals are discussed in an effort to illustrate the importance of determining, by a complete washability study, the sulfur forms and their distribution in a coal. This study will then show the extent to which the sulfur can be removed. It should be emphasized that each potential application requires a thorough study because of the varying amounts of sulfur in different coals. It is not the intent of this paper to show the best results that flotation can produce, but rather to illustrate the potential of this process and point out the importance of improved flotation techniques where sulfur reduction is involved. It is generally accepted that sulfur exists in coal in three forms: (1) pyritic, (2) organic, and (3) sulfate sulfur. Sulfate sulfur usually makes up less than 1% of the total sulfur content. Pyritic and organic sulfur make up almost all of the total sulfur content, occur in varying amounts in different coals, and can vary greatly in coal of the same seam. Pyritic sulfurs of 20% to 80% of the total sulfur have been reported. Other authors have shown that it is not possible to remove the organic sulfur without chemically altering the coal. Chapman and ones' state: "Organic sulfur, unlike pyritic sulfur does not exist as discrete particles, but is intimately associated with the coal structure, and as such it is not possible to remove it or reduce its concentration by physical means." Any success in removing sulfur has come about by removing pyritic sulfur by physical means; therefore, removal of sulfur in the pyritic form is the subject of this investigation. The extent to which any impurities can be removed from a particular coal can be determined by a washability study. Outside of crushing coal to finer sizes or chemically altering the coal, there are no known methods of changing this inherent washability characteristic. The efficiency of various methods used to remove impurities can be determined by comparison of results produced at a yield to the results as shown by a washability study. In recent years heavy media processes have proven their ability to wash plus 28 mesh coal and nearly produce results shown to be theoretically possible by the washability study. Therefore, it is the objective of this paper to show various methods of treating the finer fractions of the coal, in the hope of developing

Jan 1, 1964

By A. F. Meger

REPRESENTED here are the ideas and varied experiences of many people in the Hanna Coal Co. who have helped develop, over a number of years, an efficient and flexible method for spraying con- trolled amounts of oil on coal. Since the George- town preparation plant began operations early in 1951, oil treatment of coal has received special attention. It is believed that oil treating will satisfy present customers and also attract new markets. The first step in developing the new method of oil spraying was the construction of a dust cabinet for testing 50-lb samples of treated coal with the available oil sprays on the market. Tests results were tabulated for both indoor and outdoor storage.

Jan 7, 1954

By Roswell P. Angier, Herbert S. Kalish, Henry H. Hausner

POWDER metallurgical methods as applied to zirconium are of great interest because they permit not only the fabrication of parts directly to shape with a minimum loss of material but also the utilization of scrap, and the metal may be processed at temperatures well below the melting point. There are two difficulties involved in the melting of zirconium: 1—High vacuum is necessary for melting, and 2—zirconium reduces nearly all oxides so that it is difficult to find a suitable crucible material. The purest material, zirconium crystal bar, is expensive, and the methods of subsequent fabrication are limited. Cold rolling or extrusion of zirconium crystal bar is suitable for making certain shaped parts, but where melting is involved, the purity of the metal is invariably decreased, and a method of casting to a definite shape does not seem to be feasible. Where it is necessary to hot roll, zirconium must be covered with a steel or copper jacket to protect it from the air. This is necessarily a costly operation. Where annealing of zirconium is necessary it must be conducted in a high vacuum. In an investigation of powder metallurgical methods for zirconium, the zirconium powder used should be characterized by the following properties: 1— Highest degree of purity, 2—uniformity in particle shape and particle size distribution, 3—low compression ratio, and 4—satisfactory strength of the compacted powder (green strength). Zirconium powders have been made by two methods: By the reduction of zirconium tetrachloride (ZrC1,) with sodium,2' *•B "nd by the reduction of zirconium oxide with calcium and calcium chloride." The first method represents one of the earliest attempts to make pure zirconium metal, and the sintered product from this powder is extremely brittle. The second method of making zirconium powder is far more successful, but the powder made in this way has an extremely low apparent density and, therefore, a high compression ratio which makes it difficult to use it for powder metallurgical purposes. For these reasons the above-mentioned zirconium powders were not used in this investigation. To obtain sintered zirconium compacts of highest 'purity and good ductility, it was first necessary to produce a suitable powder. Pure zirconium has been made chiefly by two methods. The iodide method, from which the product is "crystal bar" zirconium, was developed first.'." By this purification process very soft, pure, and ductile zirconium metal can be produced. The second method, developed by the U. S. Bureau of Mines, is the reduction of zirconium chloride with magnesium." The sponge zirconium thus produced is also soft, pure, and ductile.

Jan 1, 1952

By James Boyd

As our society grows in complexity, it becomes more urgently incumbent upon scientists and engineers to bring their experience to bear on the solution, not only of technical problems, but also on socio-economic difficulties. It is to this field that I have directed a large part of my energies. Raw Materials Basic to the Economic Process There are certain premises, frequently overlooked, which bear emphasis. As economics concerns the production, distribution, and consumption of goods, so our whole society is based on raw materials. Without the basic extractive industries of agriculture and mining, there would be no economic problems with which to deal. This principle has been expressed as: "All productivity is based on three factors: (1) natural resources, whose form, place, and condition are changed by the expenditure of (2) human energy (both muscular and mental), with the aid of (3) tools."*

Jan 3, 1967

By R. E. Somers

I. Introduction...........................604 1. Location, Topography, and Climate...............604 2. Scope of Work and Acknowledgments...............606 3. History and Mining......................606 11. General Geology.........................609 1. Introduction...........................609 2. Granite. :..........................610 3. Quartz Porphyry......................... 612 4. Monzonite........................... 614 5. Volcanic Breccia........,................ 618 6. Gravels............................. 619 111. Economic Geology......................... 619 1. Introduction........................... 619 2. Mineralogy........................... 619 3. Occurrence of the Ores...................... 622 4. Oxidation and Downward Enrichment............... 630 5. Rock Alteration........................639 6. Genesis of the Ores........................ 643 I. Introduction 1. Location, Topography, and Climate The Burro Mountains are located in the southwestern part of New Mexico, in Grant county. The group is made up of two distinct mountain masses, known as the Little Burros and the Big Burros, the former lying about 6 miles southwest of Silver City, and the latter about 9 miles farther in the same direction. They are separated by the valley of the Mangas River, a tributary of the Gila, and a stream only in name, except after a heavy downpour of rain. The Little Burros attain an elevation of 6,625 ft. above sea level, and the Big Burros 8,054 ft., with the surrounding country averaging about 6,000 ft. To the south of these mountains stretches the desert plain, while to the north are the more frequent elevations of the mountainous country.

Jan 1, 1916

By Alfred Weiss

Over the past 25 years hard-rock mining companies have developed a number of profitable computer applications which appear applicable to operations in the coal industry. The evolution of these applications are described and the most profitable discussed. The basic nature of these systems is that they must cut across organizational boundaries. While technological advances contributed significantly to the successful implementation of computers within mining, the human aspects related to organization, management and control of systems projects remain as key to future success in coal as they were and still are in hard-rock mining.

Jan 1, 1983

By H. H. Podgurski, H. E. Knechtel

Annealed Fe-Al alloys do not react readily to form AlN when held at 500ºC in NH3-H2 gas mixtures, but do so upon the introduction of dislocatims. Nuclea-tion of the nitride phase occurs on dislocation sites. In turn, the growth of the aluminum nitride particles causes the ferrite phase to yield plastically, generating more dislocations for the nucleation process. The nitride phase extracted from an Fe-2 pct A1 alloy nitrogenated at 500°C was identified as stoichio-metric aluminum nitride with a hexagonal crystal lattice. THIS investigation reveals the role that dislocations play in initiating and sustaining the nitriding reaction in Fe-A1 alloys. As early as 1931 the work of Meyer and Hobrock1 suggested that the initiation of the nitriding reaction could involve a nucleation controlled process. Recently Bohnenka2 depicted the gas-phase nitriding process below 600°C as one of mixed control limited by nitrogen penetration through the surface, by nitrogen diffusion, by aluminum diffusion, and by nucleation of the nitride phase, Fig. l(a). In our research in a comparable alloy (0.57 pct Al) at 575ºC, we have observed a nitrogenation which we feel is better described by Fig. l(b). In the case of a 2 pct-A1 alloy partially nitrided at 500°C we propose the profiles shown in Fig. l(c). For a complete and accurate description of the process, a concentration profile of the dislocation density in the test specimen would be needed. EXPERIMENTAL Nitrogenization was conducted between 500" and 575°C in a variety of NH3-H2 gas mixtures on three Fe-A1 alloys: 1) zone-refined iron + 0.16 i 0.2 pct Al—levita-tion melt, 2) zone-refined iron + 0.57 0.02 pct Al— levitation melt, 3) plastiron + 2 pct Al—melted by induction heating. To demonstrate the effect of dislocations on reactivity, both cold-worked and annealed samples were investigated. All nitrogenation rate studies were conducted gravimetrically with a gold-plated invar balance4 contained in a gas-flow system. To avoid contamination of the specimens in the reaction zone of the system, the reaction chamber was constructed of high-purity dense alumina. The activity of nitrogen was fixed by specific NH3-H2 gas mixtures whose compositions were continually monitored by calibrated thermal conductivity gages and checked by chemical analysis. Variations of ± 0.1 pct NH3 could easily be detected by both methods. Throughout this paper the activity of nitrogen is defined as PN3 /PH23/2 , where PNH3, and Ph2 are partial pressures in atmospheres. Electron transmission, density measurements, and chemical analyses were made on specimens before and after nitrogenating in order to reveal structural and chemical changes. Similar studies as well as X-ray diffraction studies were conducted on nitride extractions from the nitrogenated 2 pct-A1 alloy. These extractions were obtained by the use of an anhydrous bromine-methyl acetate solution which dissolves the iron and leaves the insoluble nitrides as a residue. Hardness profiles were obtained on cross-sections of partially nitrided specimens to demonstrate the extent of nitriding through the thickness of the specimens. RESULTS AND DISCUSSION The nitrogen activity in the NH3-H2, atmospheres was never allowed to reach a level capable of producing iron nitride (Fe4N). Hence, the term nitriding as used in this paper refers only to the formation of aluminum nitride whereas nitrogenation refers to the total uptake of nitrogen regardless of how it is distributed throughout the alloy. The weight increases observed during the initial stage of a nitrogenating treatment are due primarily to the solution of nitrogen in the ferrite phase, particularly when starting with annealed specimens. Because this initial nitrogenation rate in the case of the 0.57 pct A1 alloy, see Figs. 2 and 3(a), was most rapid the weight change that occurred thereafter might be attributed to the nitriding reaction with the exception of a small weight increment due to the irreversible pickup of oxygen by aluminum. The oxygen (<70 ppm) came from traces of H2O and 0, in the hydrogen and ammonia gases. On the basis of discrepancies between total weight increase and the increase in the nitrogen content of the sample as determined by chemical analysis, it was estimated and later established by activation analysis, that as much as 200 ppm of oxygen were taken up by a fully nitrided Fe-0.57 pct A1 specimen at 575°C. Most of the oxygen could have been picked up from the nitriding atmosphere on the surface of the samples during cooling to room temperature. Even 50 ppm of water in the gas phase will become oxidizing to iron before the sample has cooled to room temperature. The lack of reactivity* of these alloys in the annealed

Jan 1, 1970

By J. Murray Riddell

The method of treating hazards wherein value is decreased, is cited by R. D. Parks. Quite properly, the theory of probabilities is made use of when multiple hazards are under consideration. E. F. Fitzhugh, Jr. $ deals with the enhancement phase graphically and uses percentage of expectancy as derived by a study of conditions and the selection of a chance factor. It is believed that both of the authors referred to fully recognize the part which human judgment plays, and as coupled with experience, training, and the application of the theory of probabilities; in that respect the composer of this paper is in accord. Within the past year, the task of arriving at a mathematical method for handling the enhancement phase, and, additionally, coupling the negative and positive phases, was explored. In citing the hazard, or negative phase, reference is made to the text by Parks. Types of Items far Consideration On the hazard, or negative, side some of the common items to be considered are: 1. Subsidence and resulting damage. 2. Flo wage of water above that anticipated. 3. Geological. (a) Decline in quality of probable ore, and/or (b) Decline in quantity of probable ore. 4. Depressed economic conditions. 5. Litigation. Similarly, on the enhancement, or positive, side common items to be considered are: 1. Flo wage of water below that estimated. 2. Geological. (a) Increase in quality of probable ore, and/or (b) Increase in quantity of probable ore. 3. Elevated economic conditions. 4. Litigation. 5. Technological advance in the art. Tn all of the above items no consideration is given to placing a value on, or giving consideration to, possibilities. For example, referring to Table 1, the estimated normal present value (Vp) of a property, exclusive of risk consideration, is taken as $100,000. If subsidence affects the usefulness of the shaft, the present value of the property will decrease to $60,000, and it is judged that there is a 1 in 4 chance that the shaft will be impaired;, consequent.ly, if subsidence took place, the present value would be reduced ($100,000-$60,000) $40,000, but since the chance is 1 in 4, the allowable reduction would be only one-fourth of $40,000, or $10,000, or a discount of 10 pct (hazard factor) of the original value; the related safety factor is taken as unity minus 0.10, or 0.90. Thus, the original Vp, $100,000, multiplied by the safety factor ($100,000 X 0.90) gives $90,000, which is the adjusted present value of the property in this single instance. Additionally, there is a water hazard, which, if encountered, will reduce the present value to $85,000. The chance is 1 in 3. Following through with the same reasoning as shown above, the derived safety factor will be 0.95. To arrive at a single multiplying factor which will express the combined risks, the two safety factors are multiplied together, 0.90 X 0.95 = 0.855. That factor when multiplied by the origirial Vp will give the adjusted, and

Jan 1, 1950

By Y. Zimmels, I. J. Lin, I. Yaniv

The potential application of magnetic and electric separation techniques in beneficiation of fine-particle feeds are reviewed. Special features of these techniques are considered and compared with a view to increased amenability of such feeds to separation in electro- magnetic fields. The following techniques are discussed, with reference to those already developed and in use to-date: - Differential-susceptibility separation (DSF). - High-gradient differential-dielectric separation (HGDDS). - High-gradient magneto-gravimetric separation (HGMGS). In this context the new approach - whereby selectivity of solid- solid separation processes, in wet high-gradient magnetic and electric separation, can be improved - is described, including experimental results from DSF and HGDDS tests.

Jan 1, 1980

By Shawn T. Sorrell, Carl Hrovatic

Original by Carl Hrovatic and Shawn T. Sorrell Revised by Carl Hrovatic Land is a precious resource and should be treated as such by all members of our society. The soil covering this earth is only a very thin outer layer, varying in thickness from a few inches to a few feet and covering the rocks and minerals lying beneath the surface. The wise use of this valuable commodity is the responsibility of everyone. Many everyday activities disturb the earth&apos;s surface. Examples are highway construction, housing and commercial developments, agriculture, and various types of mining. This chapter discusses the relationships of the environment to land as it applies to surface operations in the coal industry. Mining by surface methods disturbs, for a brief period of time, thousands of acres of land annually. In addition, refuse piles, slurry ponds, abandoned mine structures, unprotected mine openings, and unsightly cleaning plants can also adversely affect land unless properly handled. ACTIVE SURFACE MINING OPERATIONS Mining by surface methods includes rock quarries; sand and gravel pits; huge open pits to extract iron, copper, phosphate, and other ores; and coal mining. Production of coal by surface methods is now approaching 408.2 Mt/a (450 million stpy), amounting to almost 60% of the total coal output. Surface coal mining can be classified into the following five broad categories : Open-pit mining is practiced where coalbeds are extremely thick, as in some western states, or where coalbeds are sharply pitching, as in the anthracite region of the eastern United States. A typical open-pit mine, with coalbeds of 3.05 to 30.5 m (10 to 100 ft) or more thickness and a

Jan 1, 1981

By E. R. Dean

A wire-feed mechanism has been employed to fabricute metal alloy film resistors to various sheet resistivities on oxidized silicon substrates. The effect of several thousand hours storage in air at elevated temperatures on the resistance and temperature coefficient of resistance is presented. Unprotected films of- sheet resistivity between 100 and 500 ohms per sq fabricated at 300°C substrate tenzperatures were unstable when stored at 150°Cfor extended periods. The higher sheet resistivity films exhibited the greatest instability; however, even the 100 ohms per sq films drijted excessively for device application. When stored at still higher temperatures, the normalized resistance increases to maximum, then decreases until a minimum value is obtained, then finally increases in resistance until open. The use of a protective overcoating of SiO has had considerable benejicial effects on the film stability, so that 250 ohms per sq films deposited on 300°C substrates are now stable after 1000 hr storage at 250°C and possess a temperature coefficient of resistance less than 200 ppm per C. The use of a low substrate temperature during depositon (100°C) enables the preparation oj resistors with very low tenperature coefficients of resistance (10 to 20 ppnl per &apos;C). However, these films are less stable than their higher substrate temperatuve counterparts. During extended storage, the resistance of the protected films always decreases with lower substrate films exhibiting larger normalized resistance decreases. This resistance decrease is accompanied by a linearly related increase in the temperature coefficient of resistance. The electrical behavior of these films may be explained by postulating That the structure of the films is in the transition region between thick continuous films and ultrathin island structure films so that the conductivity is the restlt of both electron scattering and tunneling-activated charge carrier creation between neighboring grains. The annealing behavior when thermally aged is the result of defect anneal, grain growth, and selective oxidation. TheRE is a considerable interest in thin metallic films for use as resistor elements in microelectronic circuits.1,2 These resistor films must be stable when exposed to elevated-temperature storage or operating ambient, possess low temperature coefficients of resistance (hereafter referred to as T.C.R.), and be of a high enough sheet resistivity to be useful. The resistivity and T.C.R. of a thin metallic film are determined by the structure and thickness of the film. Hence the stability of the film when exposed to stress would depend on the stability of the structure. The resistivity of a thin film is the result of the electrons&apos; interaction with the lattice vibrations (electron-phonon scattering), scattering of electrons due to impurities, defects, and grain boundaries and specula reflection from the film surfaces.3&apos; All of these effects serve to reduce the electron mean free path and result in a resistivity higher than the ideal bulk. In ultrathin films possessing essentially an island structure consisting of a planar array of aggregates separated by a few to a few tens of angstroms, conduction is dominated by a combination of tunneling and activated charge carrier reation. Thin films would be characterized by relatively low resistivity, positive T.C.R., and reasonable structure stability whereas ultrathin films possess unstable structures, negative T.C.R., and exhibit high resistivity. Feldman6 has investigated films intermediate between the two regions and postulates that the resistivity of a film in the transition region is composed of two linearly additive parts: that due to the resistance of the grains and that due to the gaps. The grain resistivity would represent the scattering of the conduction electrons by defects, surfaces, and phonon interaction while the gap term represents the tunneling contribution. For gold and platinum films, he found as the film structure becomes progressively less continuous, corresponding to thinner films, the absolute value of the T.C.R. becomes progressively smaller until negative values are observed with respective zero T.C.R.&apos;s at about 35 and 150 ohm per sq, respectively. Recently the author7 investigated the behavior of a multicomponent alloy of nickel, chromium, and iron and found the T.C.R.&apos;s of these films decrease with decreasing substrate temperature during deposition. The lower T.C.A. associated with lower substrate temperatures was attributed to an increased contribution to the total resistivity from the negatively temperature-dependent gap tunneling since it is well-known that thin films deposited on low-temperature substrates consist of a higher density of smaller grains than the same sheet resistivity films deposited on higher-temperature substrates. Under conditions of thermal anneal, the author found that, when various sheet resistivity films fabricated at 300°C substrate temperature are exposed to extended storage in air at 300°C, the thinner films increase in resistance until open, while the thicker films

Jan 1, 1967

By George W. Harris

In the earlier period of anthracite-mining, much coal was wasted, both underground and in the culm-banks on the surface. Such waste is common in the development of new mining-districts, in which, as a rule, only the richest material can be profitably treated. In the anthracite-region, special causes operated to increase this evil. The mines were generally worked under 20-year leases, and royalties were paid upon such coal only as was actually marketed. The lessees consequently cared for immediate profit solely. They were not bound to win all the coal they exposed, or to leave it in such condition that their successors could win it. Nor was it their interest or duty to educate consumers in the use of their product. The market called for coal of large sizes; and such coal they furnished, throwing away the rest. Any pains taken by them to bring about a more rational use of coal by their consumers would have borne fruit, after their leases had expired, to the benefit of somebody else. A full statement of the situation was given in 1893, in the report of the State Commission, appointed in 1889 to investigate the subject.&apos; That body included the names of Heber S. Thompson, William Griffith and the late Eckley B. Coxe.2 Its report gives special attention to the utilization of the old culm-banks.

Jan 1, 1906

K. T. Aust and J. W. Rutter (General Electric Research Laboratory)—We find it difficult to reconcile the activation energies determined by Gifkins with his general conclusion that "migration during both creep and grain growth can thus be treated on the basis of the same model" (that of Lucke and Detert). Gifkins finds the activation energy for grain boundary migration during creep to be 24.5 kcal per rnol and that for grain boundary migration during grain growth to be 7.5 kcal per mol. The calculation carried out by Gifkins of the activation energy for grain boundary migration during grain growth, using the Lucke and Detert model, gives a value of 20 to 24.5 kcal per mol, rather than his experimental value of 7.5 kcal per mol. The theory of Lucke and Detert was developed to account for the rates of migration of grain boundaries in the presence of impurities during grain growth. The theory does not take into account the effect on the boundary migration of another, simultaneous process such as creep deformation and would be expected, therefore, to be applicable only to migration during grain growth. The fact that Gifkins measured a different activation energy for boundary migration during grain growth (7.5 kcal per mol) from that during creep (24.5 kcal per mol), although the specimens were of the same composition, shows clearly that such an effect exists under his experimental conditions; the presence of a simultaneous creep deformation markedly affects the boundary migration process in comparison with what would be observed under the same conditions but without the creep deformation. The failure of McLean&apos;s equation (Eq. [4] of Gifkins&apos; paper) to give a satisfactory dislocation density difference for boundary migration during creep is not surprising, since the activation energy which must be used in this equation refers only to the elementary atom transfer process of grain boundary migration. This activation energy value is approximately 6 kcal per mol for zone-refined lead, as determined in both the grain boundary migration experiments of Aust and Rutter31, 32 and the grain growth experiments of Bolling and Winegard.33 Using this activation energy value, McLean&apos;s equation gives reasonable agreement with observed migration rates for grain boundaries moving free of the influence of impurities.31, 32 The value of 24.5 kcal per mol is probably associated with the presence of impurity atoms, as Gifkins suggests. It should be noted, however, that this value was obtained using lead of only one composition and measurements at only two temperatures. The work of Aust and Rutter3"&apos; on the effects of tin, silver, and gold on grain boundary migration in zone-refined lead in the temperature range from 320" to 200°C, as well as the work of Bolling and Winegard34 on the effect of silver and gold on grain growth in zone-refined lead, shows that the measured activation energy is markedly dependent upon the kind and amount of solute present. Gifkins&apos; work does not permit evaluation of the effect of the 8 ppm of impurities other than oxygen present in his specimens. One incidental point: the symbols used to designate the experimental points of Fig. 6 appear to be in incorrect order in the figure caption. As the caption is printed, it would indicate that larger grain sizes were obtained after annealing at 47°C than at 100°C, which does not agree with the text (point M, p. 1019). Finally, it seems clear from Gifkins&apos; results that any serious attempt to determine whether grain boundary migration and grain boundary sliding during creep occur with the same activation energy, as Gifkins suggests and McLean rejects, must take into account the effects of impurities on these two processes, Although the work of Weinberg35 indicated that adding small amounts of copper, iron and silicon to aluminum did not affect the grain boundary shear behavior, it should be noted that his starting material contained approximately 60 ppm of impurities. Gifkins&apos; results indicate impurity effects at an impurity level of 8 ppm, suggesting strongly that the most significant impurity range to be investigated lies substantially below that value. R. C. Gifkins (author&apos;s reply) — As Drs. Aust and Rutter suggest, the results under discussion may have to be reinterpreted in the light of their own work on grain boundary migration, which was not available to me when the paper was written. Because of their work, Aust and Rutter attach more importance than I did to the activation energy for grain boundary migration during annealing (7.5 kcal per mol) obtained from a "direct" plot of log-rate against the reciprocal of absolute temperature. At the time it was obtained, this value seemed rather low, although it was similar to the value obtained by Bolling and Winegard.36 It was then, and still is, difficult to accept this value because of the low value of the index in the power law for grain growth, which seemed to indicate the influence of impurities. It was also concluded that the low value of the activation energy might have arisen from the manner of selecting rates of grain growth which were truly comparable at the two temperatures. There were many other indications in these experiments and those on recrystallization during creep3? that an impurity, probably oxygen, was of importance. The model for grain-boundary migration which Lucke and Detert had proposed was an obvious possibility and its use yielded an activation energy for boundary migration during annealing of 20 to 25 kcal per mol.

Jan 1, 1961

By W. G. Woolf, E. R. Crutcher

The electrolytic zinc plant of the Sullivan Mining Co. is in Government Gulch, at Silver King, Shoshone County, Idaho, in the Coeur d&apos;Alene mining district, about one mile from the Bunker Hill smelter and about three miles from Kellogg. The Sullivan Mining Co., which owns both the zinc plant and the Star mine, is itself owned jointly by the Bunker Hill & Sullivan Mining & Concentrating Co, and the Hecla Mining Company. The Tainton high-density, high-acid process is used at this plant, therefore some parts of its flowsheet differ markedly from those of electrolytic plants using the low-density process. While it is a custom plant and has treated a variety of zinc concentrates originating from various sources in a number of states, it has obtained its main supply of zinc concentrates chiefly from the zinc-bearing ores of the Coeur d&apos;A1ene mining district, of which the principal important sources have been the Bunker Hill and Star mines. Thus the main feed has been zinc concentrates obtained from complex lead-zinc-silver ores. For the year of 1935 the concentrates had the following composition: water, 9.5 per cent; Zn, 50.6; Pb, 3.3; Fe, 9.4; S, 31.0; Cu, 0.2; insoluble, 2.9. Flowsheet The concentrates are delivered to the plant in railroad cars, which discharge into storage bins directly under the track. Bottom-dump cars are dropped directly into the bins while a slip scraper, pulled by an air tugger hoist, is used to empty box cars. There are five storage bins for concentrates, each of approximately 300 tons capacity. At the bottom of each bin there are individual belt feeders that discharge onto a common conveyor belt, which in turn discharges to another belt that carries the concentrate onto a weightometer belt for weighing. Immediately after the weighing, the crushed oversize return from the roasters is added to the load on the belt and then the ground-up sweepings, lumps and roaster cleanings. An electromagnet at the end of this conveyor removes tramp iron from the feed. The belt discharges to a set of 30 by 12-in. rolls, which break up lumps or frozen chunks of concentrate, etc. Beneath the rolls there is a screw conveyor, which conveys the roll discharge to a

Jan 1, 1937

"Minerals in Transition" is the timely theme of this year&apos;s SME-AIME Fall Meeting and Exhibit, to be held September 10-12 at the Salt Palace, Salt Lake City, Utah. Approximately 2000 members and guests are expected to attend the meeting, which will include 117 technical papers, presented during 27 sessions. To complement the technical program, a record number of mining manufacturers and suppliers will be on hand to exhibit the latest in equipment innovation and professional services.

Jan 8, 1975

By D. N. Hedges

This paper discusses the actual recovery and installation of a longwall in a bituminous coal mine in western Pennsylvania. The coal bed mined is in the Lower Freeport seam, which averaged 1.07 m (42 in.) in height locally. Drainage from the mine is about 13.25 ML/day (3.5 million gal per day) of water. This water deteriorates the mine&apos;s predominately fire clay bottom making it extremely difficult to move equipment. Support removal is accomplilshed by pulling the 5.44 t (6 st) shields out under their own hydraulic power and transporting them by track 8.05 km (5 miles) to the next longwall panel. This paper also discusses the changes that will be made to aid in the succeeding longwall recoveries and installations.

Jan 1, 1985

By M. J. Greaves, Alan English

Pelletizing on a commercial scale is only 10 years old; yet in this period more than 150 million tons of pellets have been produced. Instrumentation and controls have played an important part in the development of an entirely new industry in almost unprecedented time. Initially, most control circuits used in the pelletizing industry were manually operated, since the confidence factor in instruments and controls was quite low at that time. This changed considerably in recent years and improvements in the use of instruments and controls have probably developed more rapidly in pelletizing than in any other metallurgical process. Now, within a decade of the start of commercial operations, the use of manually operated controls has changed and consideration is being given to the utilization of computers for data logging and control purposes.

Jan 7, 1965

By H. E. Rorschach

Activity in Oklahoma oil fields made 1937 one of the best years since 1926. During the year, 3454 wells were completed, an increase of about 25 per cent over the year 1936. Purchasers reports filed with the Corporation Commission of the State of Oklahoma showed a total of 221,842,-788 bbl. of oil purchased from leases in 1937, an increase of about 10 per cent over 1936. The assembly of a complete table of all of the oil fields in Oklahoma has not yet been achieved. Many of the early records of operators and pipe-line companies are incomplete. Table 1 includes all of the new fields, and this year there has been added work done covering pools discovered in previous years, so that most of the important fields in the state of Oklahoma are included therein. The outstanding development of the year was the discovery of the producing horizon classified as the Wilcox in western Payne County by the Mid-Continent Petroleum Corporation on a unitized block in sec. 18, Tp. 18 N., R. 2 E. This block is operated hy the Mid-Continent and owned in conjunction with the Carter Oil Co., Transwestern Oil Co. and Sinclair-Prairie Oil Co. Another important development of the year was the extension of the deep zone in the old Fox-Milroy area of Carter and Stephens Counties. Some of the other discoveries made during the year 1937 are South Cromwell, discovered by Sinclair-Prairie Oil Co.; Cromwell extension of the Fitts pool in Pontotoc County; discovery of the Langston area in Logan County; discovery of the Sporn area in Lincoln County by Skelly Oil Co. and the discovery of the North Wellston area in Lincoln County by Standard Oil & Gas Co. Table 2 shows the new oil areas discovered in Oklahoma during the year 1937 and areas that were discovered in 1936 but developed in 1937. Fox-Milroy Area.—Three wells were completed to the deep producing zone during the year. One of the wells completed in the early part of the year uas the Carter Oil Company&apos;s No. 1 Harley in sec. 24, Tp. 2 S., R. 4 W., 3 1/2 miles northwest of the original discovery well, the Ruth

Jan 1, 1938

By Douglas A. Anderson

We have instrumented well-controlled free-face blasts with six- component borehole strain gages, in order to determine the complete strain tensor as a function of time due to explosive loading. The strain tensors have been diagonalized to determine the principal strain time-histories, and further processed to determine the octahedral shear strains as a function of time. Principal strain time-histories, when compared with a computer model, indicate the arrival of various direct and reflected phases. Strong shear strains coincide with the expected arrival time of shear waves. These shear waves are probably instrumental in the fragmentation of confined rock due to explosive loading, and should be incorporated in models of the fragmentation process.

Jan 1, 1984

By Ronald Gibala

THE Au-Ni alloy system is one of many binary systems in which the supersaturated solid solutions may exhibit a multistaged precipitation behavior during aging. In addition to the equilibrium phase separation, which was studied extensively years ago in the range 400" to 600",&apos; there exists at least one earlier stage of precipitation, i.e., preprecipitation, which occurs below 300°C in quenched alls.-This note reports on some effects of composition on the preprecipitation in Au-Ni alloys as determined from resistivity measurements. The kinetics of the preprecipitation were studied in alloys of 15 to 85 at. pct Ni which were water- were found in alloys which after various quenching-and-aging treatments were slowly heated and cooled (1Z"C per hr) between room temperature and about 300°C. Two such heating-cooling curves for a 40 pct Ni alloy are shown in Fig. 2. Similar effects were observed in other 15 to 50 pct Ni alloys. These curves are characterized upon heating by two changes in slope indicated by A and B in the figure and upon cooling by a resistivity hysteresis of approximately the size of the original decrease in resistivity after the aging treatment. The inflection at B generally falls at about the same temperature for all heating curves for a given alloy and appears to be a critical temperature (T,) for the preprecipitation for that alloy. The values of T, for most of the 15 to 50 pct Ni alloys fall in the range 200" to 220°C. The position of the inflection at A depends upon the heat treatment prior to the heating-cooling run and perhaps the heating rate, which was held constant in these runs. The preprecipitates grown in by the appropriate aging treatments seem to decrease in size as the alloys are heated from A to T,, dissolve at T,, and do not reappear after cooling below T,. When similar heating-cooling treatments were performed on 60 to 85 pct Ni alloys, an entirely different behavior was observed. Typical results are shown in Fig. 3 for an 85 pct Ni alloy. In these

Jan 1, 1964