Search Documents

By J Zhou, D M. Hunter, S M. Iveson, K P. Galvin

The REFLUX Classifier is used to perform particle separations on the basis of density utilising a set of parallel inclined channels positioned above a vertical fluidised section. In continuous mode, feed enters part way up the vertical section, while fluidisation water is introduced from below. Lower density particles are conveyed upwards and collected in an overflow stream, while high density particles segregate onto the inclined surfaces, settle to the base of the system and empty via an underflow stream. Pressure transducers are used to measure the suspension density in the vertical section. This suspension density is maintained by a pneumatically controlled underflow valve to maintain a target suspension density or ‘set point’.Previously, Galvin et al (2010) demonstrated the significant improvement achieved via a new laminar-shear separation mechanism, achieved by utilising closely spaced inclined channels in the REFLUX Classifier. For the separation of low-density coal particles from mineral matter, a channel spacing of 6 mm proved effective; however, for the separation of gangue minerals from much higher density minerals such as iron ore, the shear-induced lift needs to be even higher. In this paper, we examine the influence of two different channel widths on the continuous processing of an industrial iron ore feed in the REFLUX Classifier. It was found that when moving from 6.0 mm to 3.0 mm channels, the ability of the system to reject coarser gangue material and retain finer high density material across a particle size range from 0.125 to 1.0 mm was increased, resulting in a higher grade product.CITATION:Hunter, D M, Zhou, J, Iveson, S M and Galvin, K P, 2017. Influence of shear rate on separation of iron ore fines using the REFLUXTM Classifier, in Proceedings Iron Ore 2017, pp 205–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

This paper presents an overview of the current status of mine water management in South Africa. The regulatory framework within which mine water management operates is set out, based on the principles and policies embodied in the relevant legislation. The status of the gold and coal mining industries, with regard to water management, is presented on the basis of studies that have been undertaken to develop water and salt balances for these industries. While the data is not available to quantify the status of ARD in South Africa, the range of typical mine water quality problems faced by South African gold and coal mines is presented. The status quo, problems and challenges relating to mine water management are presented and discussed. It is shown that, while there have been major strides in the last decade, and mine water management and treatment in South Africa has moved onto the forefront of mine environmental management, important problems still persist. There is still a significant amount of improvement required, particularly in the field of prediction of water quality deterioration and the application of such predictions to the identification of management actions that can be applied to prevent or minimise mine water pollution in the shortmedium- and long-term.

Jan 1, 2003

By E Coffison, M Gibbs, C Bennett

The sustainable management of surface water associated with coal mining and coal seam gas projects is a considerable factor affecting the global competitiveness of these resource companies operating in Australia. Management of surface water can be costly, but effective water management and hence environmental stewardship enhances corporate social responsibility and the social license to operate. The surface water issues for the two industries are comparable, yet there is currently a lack of alignment between how Queensland, where the majority of AustraliaÆs coal seam gas projects are located, manages and regulates water on coal mine projects and coal seam gas projects.This paper provides a high level comparison of Queensland legislation and highlights the lack of alignment of this legislation regarding surface water management in these two industries. Through a case study, it looks at the surface water management process at a coal mine site based on the current legislation and principals of surface water management. QueenslandÆs lack of alignment in legislation regarding surface water management in these industries is understandable given the different development paths and time scales of the two industries. The coal mining industry has developed over a long period of time and the legislation has progressed in parallel, whereas, the coal seam gas industry is relatively new in Australia and the legislation has had to advance quickly. The lack of alignment between management of surface water for the two industries creates confusion among stakeholders and this adds complexity and additional transaction costs during the exploration, permitting and operational phases of projects, including landowners who may be affected.CITATION:Bennett, C, Coffison, E and Gibbs, M, 2013. Lack of alignment between regulation of surface water management in coal mining and coal seam gas, in Proceedings Water in Mining 2013 , pp 157-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

Conventional treatment of oxide and oxidised sulphide minerals by flotation involves the use of sodium sulphide for sulphidisation. Sodium sulphide is generally applied in a "slug" dosing fashion with manual regulation. However, it is recognised that "over addition" or "under addition" of sulphidising reagent can result in poor flotation recoveries. Thus, control of sodium sulphide additions is an important aspect of a sulphidisation circuit, both commercially and metallurgically. In any plant where the flotation feed is "constant" it is possible to operate at a constant rate of addition of sodium sulphide. In actual plant practice, however, it is difficult to maintain a truly constant feed for any reasonable duration because this implies not only a constant feed-rate, but also constant mineral composition and particle size range. These factors can vary significantly and ideally require corresponding variations in the additions of sodium sulphide to maintain optimum recoveries. To cope with variations in the feed, it is essential to have automatic rather than manual regulation of the sulphide reagent addition. The CPS process achieves this control by utilising a sulphide ion-selective electrode as a control instrument in sulphidisation. The CPS process which uses a selective electrode, enables the sulphide ion concentration in the flotation pulp to be monitored and controlled continuously throughout the stage of sulphidisation.

Jan 1, 1989

Enterprise Optimisation is a methodology for increasing the value of mining and mineral processing operations through better long-term planning decisions. It involves a combination of ten mechanisms which deal with decisions at different stages of the value chain. A decision made at any point in the chain potentially affects the decision for all other points in the chain. The key, therefore, is to optimise them simultaneously. The Enterprise Optimisation approach can be shown to produce increases of five per cent to 35 per cent or more in net present value (NPV), even when several optimisation methods have already been applied. This paper steps through an example case study, illustrating the effect of each mechanism and how they can work together to develop greatly improved results. This example results in a series of counter-intuitive outcomes, which challenges conventional management practices and typical organisational objectives based on organisational silos.

Dec 6, 2010

By E S. Weiss, S P. Harteis

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) has conducted full-scale explosion experiments, to evaluate the strength characteristics of various seal designs, used for safely isolating worked-out areas in underground coal mines. Large-scale explosion tests conducted within the multiple entry section of PRLÆs Lake Lynn Experimental Mine (LLEM) is currently the only accepted test method used by the Mine Safety and Health Administration (MSHA), for deeming a seal design suitable for use in American mines. These explosion tests are labour intensive, expensive to conduct, and can interfere with other critical underground safety and health research programs conducted by NIOSH. The PRL has developed an alternative seal evaluation method, based on a hydrostatic pressure loading concept, that can facilitate the in situ testing of seals in an operating mine. Two chambers within LLEM and one within PRLÆs Safety Research Coal Mine (SRCM) were used for hydrostatic pressure loading various seal designs. The results from these chamber tests compare favourably with those from the large-scale explosion tests in the multiple entries. In addition to testing seal designs at the required 20 psi static pressure level, the chamber test approach also allows for the determination of the sealÆs ultimate design strength. Size-scaling relationships for predicting the strength of seal designs as a function of entry size are also presented.

Jan 1, 2005

By Jardine G, Woodall C

The Henty Gold Mine, located in Western lasiuania use, uuiusatise solutions to effectively manage a mining operation in an environmentally sensitive setting and has been presented with several environmental awards. Fill is required as part of the mining method to provide passive ground support, minimise rock exposure and ensure maximum recovery of the small but high-grade orebody. The use of the whole portion of leach residue in the backfill reduces the surface tailing disposal requirements. Therefore, High Density Paste Fill (HDPF) has been selected as the most appropriate fill method to meet these objectives. Additional benefits include the minimisation of excess water from fill and the subsequent need for the collection and treatment of water and slimes. There are minimal equipment requirements during placement, thereby optimising mine resources for production. The initial paste fill design was based on the Bad Grund and Ranunelsberg Mines paste fill systems of Preussag in Germany and comprised pumping filtered tailings paste some 1.2 kin uphill from the mill to the mine portal, where cement was to be added before being distributed underground. The system was designed following initial testwork that was undertaken on a bulk sample of ore mined from the scar surface Sill Zone. Subsequently, during the mining of the Zone 96 orehody, it was found that there were significant mineralogical variations in the composition of the ore mined. Following processing, the resultant Icach residue caused significant changes in the paste rheology and therefore the pump and flow characteristics. An alternative solution was implemented that involved the use of agitator trucks to transport the cemented paste to the portal. This required modifications to the fill preparation system and also the underground distribution system. Laboratory strength tests of the HDPF using actual gold plant leach residue showed low early strengths were attained with HDPF containing only filtered leach residue. Therefore, high binder addition rates or an increase in the fill cycle time would be required to allow the fill to gain sufficient strength. A considerable amount of potentially acid generating waste rock also requires underground disposal. By blending the waste rock with the HDPF, the strengths were improved and the required cement addition rate reduced by about one-half. The potentially acid funning waste rock is encapsulated in the highly alkaline cemented paste, minimising the potential for acid generation.

Jan 1, 1998

By P J. Cullen, B P. Banerjee, S Raval

Continuous monitoring of mining impacts on the surrounding environment is a necessary sustainability criterion. Traditional monitoring approaches such as in situ sampling and airborne and satellite-based remote sensing have several limitations. Over the past few decades, unmanned aerial vehicles (UAVs) have evolved into popular platforms for remote sensing. UAV-based remote sensing has been successfully applied in different sectors, including agriculture, forestry, urban environments and disaster management. However, the potential of UAVs for mine environmental monitoring has not yet been fully established. This paper envisages the use of UAVs and sensor systems to monitor the environment of future mines.CITATION:Banerjee, B P, Raval, S and Cullen, P J, 2015. Unmanned aerial vehicles for mine environment monitoring, in Proceedings Third International Future Mining Conference, pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By R Lastra, Y Choi, C Hamilton, P Kondos

Hydroseparation (http://www.cnt-mc.com) was used to concentrate sized fractions (from <38 ¦m to 150 ¦m) of various ore products ahead of carbon-in-pulp (CIP)-treatment. The resulting size-by-size concentrates were mounted as monolayer polished sections and subjected to automated unattended precious metal searches by image analysis (see Lastra, Wilson and Cabri, 1999). Systematic variations in Au-deportment permit quantification of Au reporting as discrete grains from fresh-feed through to pressure oxidation (POX)- and CIP-feed. Application of hydroseparation, image analysis and assays to characterising tailings (from <10 ¦m to 106 ¦m) from four mine sites is also described. Results are encouraging enough to predict that the combination of hydroseparation (HS) and automated image analysis could become a standard methodology for study of precious metal ores and metallurgical products.

Jan 1, 2008

A brief history of the significant haulage truck feature changes and the factors that influenced those changes during the 60's and 70's provide a basis for forecasting the changes that can be expected in the 1980's. A review of the impact factors and changing requirements that currently exist that will create changes. Define the critical requirements of a successful haulage truck design and discuss the availability of bigger engines and better electric drive componetry to provide deeper pit capability and improve reliability. The Unit Rig Trolley Assist System to provide improved productivity and diesel fuel savings and an economic analysis to evaluate the Trolley System is covered. The Unit Rig Automatic Truck System for a driverless truck is covered in concept and discussed from the point of view of the experience in a test in a New Mexico mine. INTRODUCTION A good basis for trying to forecast what is going to happen in the future is to go back a little bit in history, to see what the influencing elements were in different periods of time as a foundation for the forecast. INFLUENTIAL FACTORS IN THE 1960'S If you look at the truck development that occurred in the 1960's, there were some identifiable factors that give us insight. (See Fig. 1) Several things happened at the beginning of the 1960's. Mechanical drive haulage trucks were introduced that were

Jan 1, 1982

Flotation testing has been done at laboratory scale on hematite mineral and ore samples using stage additions of various hydroxamates. Chemisorption of hydroxamate species onto the hematite surface was inferred from the results, possibly involving both the undissociated hydroxamic acid and hydroxamate ion as maximum recovery occurred close to the pKa of the hydroxamic acid. Flotation testing on a specular hematite ore containing 40 per cent Fe and 42.5 per cent silica gave highest iron grades in concentrate at pH 6, in contrast to published data which suggested pH 9 as the optimum value for ore processing. Using octyl hydroxamate, a rougher concentrate assaying 67 per cent Fe at 51 per cent recovery was obtained using four stage additions of 50 g/t at pH 6. For lower grade concentrates still meeting the chemical analysis for pigment grade micaceous hematite (minimum Fe assay 60 per cent) iron recoveries of 80 per cent were possible for stage additions of 50 g/t octyl hydroxamate in the pH range 6-8.

Jan 1, 1999

A new approach to resource estimation at the exploration stage is emerging, based on the application of simple software techniques. The techniques combine the power of interactive graphics with proven database, analysis and estimation tools. With effective use of these tools the geologist now has maximum chance of deriving a reliable structural and grade model from the limited exploration data. Unlike cutoff-based polygonal methods, the resultant geological model can immediately be used to evaluate any economic scenario.These modelling techniques are embodied in MINEX-3D, an Australian software system. With the emergence of the 386-based PC and high resolution (VGA or better) graphics, MINEX-3D makes the power of this new 'desktop geological modelling' accessible to most exploration geologists.

Jan 1, 1990

By Lock PR

The Silver Swan nickel mine is located at the Black Swan Nickel Project, 53 kin north east of Kalgoorlie, Western Australia. The Silver Swan orebody is a massive sulphide nickel deposit dipping 70¦ east with an average in situ grade of 14 per cent. Mining of the massive orebody is by Mechanised Ramp Cut and Fill (MRCF). A mining recovery of 98 per cent and minimising dilution are primary goals in extracting the high-grade ore. Placing a distinguishable marker bed (working platform) on rock fill was identified as a key method to achieving these goals. Gravel from a pit located onsite was considered the most suitable material for the marker beds. Research undertaken to design the marker beds using the gravel revealed conventional methods used in mining would not suffice, but that road stabilisation methods could be a viable alternative. Trials used a road recycler to mix cement and gravel in situ and several test beds were constructed on the surface to determine the final design. The trials attempted to replicate a marker bed's life cycle of construction and placement and mucking of ore from the marker bed.

Jan 1, 1998

By R Justa Cámara, L M. Pinillos Lorenzana

Barcelona Metro Line 9 (Line 9) is an essential infrastructure, improving the transversal transport in Barcelona by connecting the greater part of the currently existing radial lines. The purpose of Line 9 is to create a peripheral line surrounding the city of 1.6 million people (metropolitan area exceeds five million), and includes 52 stations, of which a total of 32 are deep shafts and 19 transfer stations in a densely populated area with several geographical constraints.The tunnel has an inner diameter of 10.90 m, bored with an earth pressure balance (EPB) tunnel boring machine (TBM) in soil sections with precast concrete lining type universal ring and segments 40 cm thick.A single tunnel solution was adopted, driven by functionality and costs savings. The internal tunnel section is divided into two levels to allow for one way rail transit including the platforms in each station on each level in order to optimise the space created by the TBM excavation and comply with the operational needs. The division in two areas of the tunnel was carried out through the construction of a horizontal slab resting on the tunnel segments with a constant thickness of 40 cm at the central part of the slab and supporting side walls.CITATION:Justa Cámara, R and Pinillos Lorenzana, L M, 2014. Two transit levels in one tunnel tube – an innovation in Barcelona Metro Line 9, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 387–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Principles of management in ore preparation before process of enrichment of chrysotile ores are discussed. The formulas, which were tested in industrial conditions, are offered, which may be used for averaging of chrysotile-asbestos fibres by content in ore and grade.

Dec 6, 2010

The importance of orebody definition and optimisation in project development cannot be overstated. Inappropriate orebody definition is the single most important reason for project under performance and/or failure. Without the firm foundation of good orebody definition, the structure of a project cannot be assembled reliably. Many factors need to be considered in the process of orebody definition. These factors are well summed up in paragraph 123 of The Institute's Code and Guidelines for Assessment and Valuation of Mineral Assets and Mineral Securities (Valmin Code). The factors range from the initial geological data through assaying, geotechnical and hydrogeological factors to mining and metallurgical considerations. There are other factors which also need to be considered including marketing and environmental factors. This paper briefly reviews some of these factors and their impact on project development. Three examples are presented where one or more of these factors have had significant impact on the development of the Project.

Jan 1, 1997

By D Craw, P Upton

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Southern Alps of New Zealand and the mountains of Taiwan are both young transpressive orogens characterised by rapid uplift and exhumation, high heat flow and vigorous surface processes. Comparing and contrasting the two provides an ideal framework through which to explore the structural and lithological controls on fluid and gold mobility during collisional deformation. Both have two fluid flow systems centred about their drainage divide with shallow topographically-driven meteoric water above a deeper flow system dominated by mineralising rock-exchanged fluids. Despite similar tectonic settings, the distribution of heat flow, hot springs and veins in the two orogens are different. Taiwan has higher heat flow, distributed hot springs and localised veining whereas the Southern Alps have a narrow heat flow anomaly, localised warm springs and widespread veining. We use three-dimensional numerical models to evaluate key parameters that affect fluid flow and gold mineralisation. Models show that differences in crustal strength and thickness affect the locus, scale and rate of crustal fluid flow and hence influence gold deposition at a variety of scales. We explore how surface topography can lead to localised changes in the stress state, facilitating the switching of principal stresses and hence vein orientations.CITATION:Upton, P and Craw, D, 2015. Modelling structural and lithological controls on the mobility of fluids and gold in orogenic belts – examples from New Zealand and Taiwan, in Proceedings PACRIM 2015 Congress, pp 189–192 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By L Jackson, A Parbhakar-Fox, N Fox

"Characterisation of sulfide minerals (eg pyrite, sphalerite) in historic tailings can assist in determining whether there are economic benefits of reprocessing such materials using modern metallurgical practices. In addition, there are associated environmental advantages if the historic tailings are actively generating acid and metalliferous drainage (AMD). At the Old Tailings Dam (OTD), Savage River, Western Tasmania, 38 Mt of pyritic tailings were deposited from 1967 to 1982; consequently it has been recognised as an AMD source. Long-term management options considered for this site have included the establishment of either a water, hard-engineered or vegetation cover. However, due to geotechnical challenges posed and the lack of success demonstrated by previous pilot studies, these strategies have not been implemented. Instead, resolving the pyrite chemistry can allow for a first-pass assessment of whether reprocessing these tailings is a feasible option as part of a long-term management strategy for this legacy site.Tailings samples (n = 144) were collected across the OTD from up to 2 m depth from five facies (A–E), and four zones (1 to 4; defined by hydrological regime and grain size). These materials were subjected to acid-base accounting (ABA) and mineralogical evaluations to determine their geoenvironmental characteristics. Following this, 26 samples were selected for in-depth laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) investigations to evaluate pyrite chemistry across different tailings facies. The results revealed enrichment of Co and Ni in these materials. Specifically, Co content was up to 3.0 wt per cent, particularly within facies C to E, and Zones 3 and 4. Cobalt is recognised as a critical metal, therefore, reprocessing should be considered as a future rehabilitation option for the OTD, pending resource definition using established codes and practices.CITATION:Parbhakar-Fox, A, Fox, N and Jackson, L, 2016. Geometallurgical Evaluations of Mine Waste – an Example from the Old Tailings Dam, Savage River, Tasmania, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 193–204 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By I R. F MacCulloch, K Jones

Pintail Systems, Inc, a Colorado USA based company has developed and commercially applied bioremediation processes for biological detoxification of cyanide compounds in mine waste. Site-specific microorganisms are isolated from spent ore, tailings or process solutions and augmented in the laboratory for cyanide oxidation, denitrification and metal biomineralisation. Biological processes typically treat complex contaminants (cyanide compounds, soluble metals and nitrates) in a fraction of the time of conventional remediation processes. Cyanide is used in microbial metabolic processes as a carbon or a nitrogen source. Biological detoxification processes applied at the end of mine life can end long-term liability and perpetual monitoring and containment. Case studies from commercial application and demonstration programs for the US Environmental Protection Agency will be presented in this paper.

Jan 1, 2004

The optimisation of a mining operation requires precise ore grade control, metallurgical accounting, and laboratory sampling protocols, which are implemented by using accurate and flawless sampling systems. Good sampling practices, and sampling technologies in these fields have been historically poor and too many existing sampling systems available on the market are flawed in many ways. This is mainly the result of a poor understanding of the Sampling Theory, and the natural result of international standards on sampling that fail to present the Sampling Theory in a logical way, that still promote non-probabilistic sampling, and that fail to address the important details that make a correct sampling system. Many standards barely mention the Sampling Theory in appendices when it should be clearly the main body of a reliable standard on sampling. As a result, many standards show only little expertise in the Sampling Theory. Conventional statistics should only be a scientific tool for the Sampling Theory to reach its height, which has always been well understood by its creators. Conventional statistics can indeed be addressed in appendices of standards in sampling, but not the other way around. Until the Sampling Theory is recognised as the main body of a standard on sampling, incorrect sampling technologies will plague the market, and make it impossible for mining operations to optimise their mining and metallurgical processes. This paper makes a short list of correct new sampling technologies that have been created with respect to the principles taught in the Sampling Theory. Also, suggestions are presented to create better international standards on sampling, which would provide a stronger incentive for manufacturers to build correct sampling systems, and for engineering firms to install only sampling systems that respect the rules of sampling correctness listed in the Sampling Theory.

Jan 1, 2004