Search Documents

By B T. Qin, C Zhu, Y W. Jia, Y Lu, F L. Li, Q L. Shi

Air leakage through rock fractures in coal mining is a major cause of coal spontaneous combustion. In order to overcome the deficiency of the existing fire control technology and prevent coal spontaneous combustion by isolating coal from oxygen, the article proposes a novel technology of inorganic solidified foam (ISF) with high expansion to fill fractures effectively. ISF consists of fly ash, cement, setting accelerator, redispersible polymer powder, water and aqueous foam. For preparing homogeneous and stable ISF, a preparation system with a pore type foam generator, a mixer device installed with a hollow shaft and helical blades, air compressor, slush pump and monitoring instruments was developed, and the working principles of key devices were elucidated. Based on a series of experiments on the different ratios of each component material and technological parameters of the preparation system, ISF with a foam expansion ratio of 8~10 and dry density of 250–400 kg/m3 was prepared. The relationship between elastic compressive strength, modulus of elasticity and density was summarised. Based on the injection experiment for fracture of loose coal pile with high temperature, the characteristics of sealing air leakage, compressive strength, thermal insulation, flow and cooling of ISF in the fresh state were investigated, indicating that ISF can effectively cut off the air leakage and cover the coal sample to reduce the temperature in the earlier stage, and ISF can remain stable and not crack. The ISF was applied to Luwa coalmine to seal small coal pillar pressure fractures and loose coal fractures in goaf. After press-casting the ISF in Luwa coalmine, the pressure-difference of inner-outer increased, meaning the effect of external conditions on the pressure-difference decreased, showing that it could plug the air leakage effectively.CITATION:Qin, B T, Shi, Q L, Lu, Y, Zhu, C, Li, F L and Jia, Y W, 2015. The novel technology of inorganic solidified foam with high expansion for preventing coal spontaneous combustion, in Proceedings The Australian Mine Ventilation Conference, pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J Joy, A Bye, G V. Kizil

This paper presents an application of the newly developed risk-cost-benefit (RCB) framework to support risk management decisions for the selection of wall monitoring technologies at an open cut mine site. The RCB framework quantitatively assessed the risk of unstable slope-induced wall failure and its impact on both loss of life and coal recovery. The RCB framework was utilised in the selection of an optimum group of risk-controls to effectively manage the risk of wall failure to ensure safety and optimal production occurred. The RCB framework incorporates mathematical modules that integrated RCB calculations and risk-control effectiveness assessments to determine the risk reduction and financial impact of the examined safety initiatives.This paper provides an overview of the five-staged RCB framework, incorporating the RCB decision support tools, RCBGEN (Risk-Cost-Benefit Generator) and RCEMETHOD (Risk-Control Effectiveness Method), and demonstrates its application to slope stability risk management at the case study site. The RCB charts are designed to display a balance between risk, cost and benefit for easy interpretation by decision makers to support the objective selection of an optimum suite of risk-controls. The RCB analysis revealed that a combination of ævisual inspections, automatic extensometers and radarÆ for fast- and slow-wall failures with structure were sufficient to reduce the probability of loss of life (PLoL) to the æModerateÆ zone as defined by the Australian Geomechanics Society (AGS, 2007) for the case study site. The new framework presented in this paper provides a method to effectively determine the suitability of risk-controls and supports industry efforts to reduce risk to as low as reasonably practicable (ALARP).CITATION:Kizil, G V, Bye, A and Joy, J, 2012. Risk-cost-benefit analysis of early warning technologies impact for wall failure risk management in surface mines, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 55-64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By Paine GG

The in-situ retorting of shallow oil shale deposits is an attractive alternative to the material handling problems of conventional open pit mining techniques, which involve removing overburden, fragmenting and transporting the shale to a fixed retort, and finally disposing of the hot spent shale.For in-situ retorting to be successful, the oil shale has to be fractured and the fragmented rock expanded into a void, to allow controlled propagation of a flame front through the in-situ retort. The principles of cratering with explosives have been used to develop a process for the in-situ fracturing of a thin oil shale deposit overlain by a formation of porous rock. The overlying porous rock formation is first compressed by explosive charges to create voids in the porous rock. The oil shale is then fragmented and pushed in to the voids with separate explosive charges. This paper discusses methods of creating voids in porous rocks with minimal surface disturbance, and then methods of obtaining the most uniform fragmentation of the shale. The whole process can be completed, in practice, in one blast. The results of an experimental blast are presented, and possible modifications are then discussed.

Jan 1, 1985

A survey of leaching systems for the dissolution of gold has been undertaken and their advantages and disadvantages evaluated both from their effectiveness at leaching and their compatibility with carbon- in-pulp (CIP) and resin-in-pulp recovery. In the near future it is almost certain that cyanidation in some form will remain the leaching system of.choice although economic and environmental pressures could see the introduction of other leaching systems particularly for treating refractory gold ores. The most likely alternative leaching systems appear to be acid chlorine, acid thiourea and ammoniacal thiosulphate. INTRODUCTION High grade reserves of readily recoverable gold ores are gradually being depleted which, inevitably, must create a greater awareness amongst gold producers, of the efficiency and, in some cases, the suitability of present day metallurgical processes for treating low grade, complex and refractory deposits. One of the key steps in the extraction of gold is the dissolution of the metal using chemical reagents which, ideally, should be cheap or recyclable, selective, non-toxic and compatible with down-stream recovery processes. In practice, meeting all these critera is difficult - if not impossible - particularly in view of the stringent environmental impact requirements which must be met Nowadays.

Jan 1, 1982

By R Hargreaves, T Elkington, W J. Shaw, G W. Booth

Every day, around the world, thousands of tons of ore are loaded onto ships completing the miningproduction process and starting a multimillion-dollar economic transactions process. These transactions are based on the supply of tons of a commodity with certain specifications of assays of the main element (or physical properties) and concentration of contaminants, which are finally verified and evaluated by buyers, and also are considered ‘as true’ during Reconciliation process. On Sample Stations, this ‘true’ is based on a few kilograms of sample, often representing thousands of tons, that are sent to laboratories for further sample preparation and chemical analysis, where finally assay information is obtained from a few grams of pulverised sample, and are used for further production, planning, operational and financial-marketing decisions. Different International Standards (depending on the commodity) are used to establish the methodology to be followed, to set-up and obtain samples from the Sample Stations, and the specifications are visually inspected to give an estimation on the performance of the sampling point. This paper seeks to highlight with examples, the importance of the implementation of a continuously monitored Quality Program (QAQC and QM) on Sample Stations, focused on the parameters that directly affect the quality and representativeness of the samples. By this implementation, a proactive approach and better-informed decisions can be taken for mining companies to: a) quantify/improve production and reconciliation results, and b) to supply the right specifications of shipped ore, increasing the value of the Resources. Finally, laboratory results are normally used as an indication of the quality of the information applied for the economic transaction, but it should be considered, clarified and highlighted that the laboratory will only process and analyse a sample obtained from a Sample Station, and potential problems on bias or precision may occur in stages prior to the laboratory reception. Hence the importance of the implementation of a quality assurance program that protects multi-million dollar decisions.

Mar 22, 2022

By Romanovsky N. P

The Pacific Mobile Belt (PMB) is characterized by old origin and complex evolution both in time and space. As the global structure, the PMB is a narrow tectonic region dividing two plan-etary hemispheres, viz. the Pacific and IndoAfro-Atlantic ones, the relative shifting of which defines the character of many geodynamic processes in this belt. The PMB features inhomogeneity of structure, special matter composition characteristics, sharply broken-out topography, and intensive fields. Generalized anomalies of the gravitational field closely correspond to the PMB boundaries defined by the real features, i.e. the andesite line and distribution areals of Mesozoic-Cenosoic granitoids. The belt boundary position is controlled also by seismic velocity anomalies at a depth of down to 200 km. The modern PMB deformation is defined by the left-hand equatorial shift and rotation of the Pacific Ocean counterclockwise. This rotation is non-uniform in time and of an oscillating character. The motive forces of the phenomenon are considered.

Jan 1, 1990

Two independent sets of observations from rifted con-tinental margins suggest a way to reach a quantitative under-standing of how the topography of rifted margins erodes. First, a prominent erosional escarpment, which demarcates an elevated, inland region of low relief from rugged, deeply-incised terrain on the seaward side, is the main feature of the geomorphology of many rifted continental margins. Second, apatite fission track ages from the southeast Australian and southwest Saudi Arabian margins scatter about constant Paleozoic ages over the higher elevations inland from the escarpment, but decrease systematically seaward of the escarpment to near-rifting ages approaching the coastlines. We have developed erosion models based on conservation of mass principles to explain these observations. These models seek to explain the "rejuvenation" of erosion at the time of rifting, initiation of the observed erosional escarpment, and its migration inland with time at a rate on the order of 1 km/10 yr. We find from the modeling that erosion at rift flanks and passive margins is fundamentally a non-linear pro-cess. The erosional development of passive margin topogra-phy has much is common with travelling wave solutions to non-linear diffusion-type problems, and to self-similar sto-chastic processes, such as diffusion-limited aggregation. We suggest that the fission track data record the thermal effects of erosional unroofing at rift flanks and passive continental margins. Models intended to explain the erosional develop-ment of continental margins must explain both the geomor-phology and the fission track observations as well.

Jan 1, 1990

By C Lower

An unprecedented, quantitative, deposit-scale understanding of major clay mineral distribution throughout the Yeelirrie uranium deposit has been achieved by adapting the existing HyLogger™/HyChips™ analytical technique to measure resource assay pulps. Spectral analysis via HyLogger™ and HyChips™ systems has previously been used as a small-scale geometallurgical research tool, but never before has it been quantitatively applied to an entire resource sample population for the purpose of developing stand alone block models for major clay minerals. Economic uranium mineralisation within the thin but extensive Yeelirrie?palaeochannel?primarily exists within the transition zone between a groundwater-derived calcrete and the underlying clay-quartz regolith. Early geometallurgical investigations identified that certain clay minerals could be deleterious to the efficiency of the uranium recovery process. Accurate calculation of clay mineralogy from resource assays proved too difficult due to chemical similarities between co-existing kaolinite, smectite and magnesium carbonate minerals. A relatively low-cost, efficient and accurate method of quantitative clay mineral analysis was required to measure over 70 000 resource assay pulps. After initial testing and comparison with QXRD, the HyChips™ 3-1 spectral logging system was implemented as a primary method of clay mineral analysis for the Yeelirrie uranium deposit. The resultant spatial data set allowed the interpretation and geostatistical analysis of geometallurgical domains across the deposit. Clay block models were generated and used in geometallurgical resource calculations to benefit the mine planning process.

Sep 5, 2011

By N Cann

In the 10 years from 1998 to 2008 the annual number of fatalities in the Australian mining industry has plateaued (MCA, 2007-08 and abc.net.au website). Despite significant efforts to eliminate fatalities, this is not a comfortable statistic in this very public performance indicator.GHD has been working with the mining and minerals processing industry to identify the key risks that lead to fatalities utilising a semi quantitative risk assessment technique (SQRA®), initially developed to assist Major Hazards Facilities prepare Safety Cases (OH&S, 2007-08) in response to the Longford Incident in 1998 (Dawson and Brooks, 1999).Workshop cross functional teams are assembled from the sites and led by the GHD facilitators to identify the incident types that can have fatal consequences, the causes of those incidents and the controls that are utilised (or could be utilised) to reduce the risk. The risks for each incident type are quantified to produce a risk profile for the facility and the critical controls – the controls that have the greatest impact at reducing the risk of fatality – are selected. These controls are assessed for their adequacy and improvement actions are identified. Prioritisation of the actions is achieved by re-estimating the incident risk profiles.A review has been undertaken using a small sample from the more than 100 individual studies that GHD has completed at mining and minerals processing sites. The five most significant risks reported by sites are:1. Fall from Heights,2. Vehicle/ Vehicle and Vehicle/Pedestrian interactions,3. Entanglement,4. Molten Metals and Materials, and5. Electricity.The most significant reductions in risk identified were found to be by implementing engineering controls. Examples include:1. Chutes to contain splashes and spills of molten materials,2. Redesigning instrument and equipment layouts to take personnel away form high risk areas,3. Designing remotely operated equipment to remove personnel away from high risk areas,4. Proper fire fighting equipment provisions such as deluges around flammable materials, and5. Adequate risk assessment to ensure equipment is designed to handle the real situations and not a design case to meet an arbitrary specification.All of these cases and many of the actions identified in the studies could have been handled through better design and construction early in the life of a project rather than retrospectively fitted after operations have begun.

Aug 8, 2011

This paper discusses the recently com- pleted TBM-driven pressure tunnel at the Sand Bar Hydroelectric Power Project. The Sand Bar Project is a diversion scheme situated on the middle fork of the Stanislaus River in the Western Sierra Nevada, California, U.S.A. As part of the project, a 5.6 km long and 3.71 m diameter unlined pressure tunnel was bored by a Jarva TBM at the average rate of .37.5 m/ day. This report deals with construction aspects of the tunnel, including TBM performance, lining design, and remedial support measures. Correlations between TBM performance, geologic conditions, and rock properities are made, and the Contractor's mode of operations are discussed. Advance rate prediction, and the impact of these excellent advance rates attainable in hard rock using the new machines are discussed.

Jan 1, 1987

By S Robinson, A Turner, R Dale, C Butler

"Sandfire Resources NL- (‘Sandfire’) DeGrussa definitive feasibility study (DFS) identified geometallurgy as a major factor in achieving optimum plant performance at the DeGrussa mine. A geometallurgical initiative was created to proactively investigate this issue, and a key initial achievement was the 2013 paper by Condon et al (2013) on developing a working geometallurgical model from first principles. Significant advancements in Sandfire’s geometallurgical understanding since that publication now shape how information is presented and communicated.The main geometallurgical parameters so far identified as critical factors affecting plant performance are Cu:S ratio, iron sulfide mineralogy, talc carbonate content and sphalerite content. Apart from specific mill strategies, geometallurgical issues have been managed through communication between departments and strategic run-of-mine (ROM) pad management.This paper uses the current theories of geological evolution of the volcanogenic massive sulfide (VMS) deposit at DeGrussa, to discuss the variability between the orebodies C1, DeGrussa (sea floor mounds) and C4, C5 (sub-sea floor replacement) to highlight the different issues each orebody is expected to encounter when processing.A zone of altered low-grade mineralisation surrounds the main orebodies at DeGrussa, referred to as a halo. Talc minerals are often patchy within this halo and often cause significant recovery issues during processing. This halo has been successfully modelled using MgO as a proxy. The ability to model the talc material assists with both identifying potentially problematic zones for processing and geological interpretation of the ore deposits evolution.Early in geometallurgy studies at DeGrussa it became apparent that it would be useful to identify processing performance prior to mining. This necessitated the incorporation of specific sulfide species into the mining block model. These attributes are interpolated from the logged sulfide estimates allowing a clear picture of the abundance of each mineral type within a defined area.In conjunction with the block model a geometallurgical factor (GMF) graph was developed, identifying sulfide mineralogy based upon mineral assays. These two recent additions to the model provide a clear picture of the nature of the ore sources that will be presented to the processing plant.The future of geometallurgy at DeGrussa will see these tools used to aid mine scheduling with a view to further improve processing recoveries.CITATION:Butler, C, Dale, R, Robinson, S and Turner, A, 2016. Geometallurgy – Bridging the Gap between Mine and Mill: a Case Study of the DeGrussa Geometallurgy Program, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 77–88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By J Loeb, R Ramanathan, H Ingham, P Cameron

Most mining operations, including iron ore, maintain a focus on continuous improvement and asset optimisation in their operations. As all the unit operations in the Mine-to-Mill value chain are interdependent, available technologies that address efficiencies across the value chain are once again in the spotlight as companies are driven to improve productivity and maximise mine site profits to increase return on capital invested. Core to continuous improvement is the need to understand the baseline and impact of changes to the process. In this paper, we discuss some of the critical attributes in the Mine-to-Mill process, including their influence on productivity and cost, the need for direct measurement and areas where they should be applied. Many initiatives can be considered to improve Mine-to-Mill processes. Mining operations are planned and executed based on designs and models to achieve the operation's objectives. However, there are many variables in the different parts of the value chain, such as blasting, material handling, crushing and screening. Therefore, measurement of the key attributes establishes the baseline for Mine-to-Mill (or Pit to Plant) performance, which is necessary to understand the impact of any proposed improvements to the process design and execution and monitor the outcomes on an ongoing basis sustain the improvements that have been implemented. This paper focuses on two types of measurement – blast movement and particle size of materials through the Mine-to-Mill process. Several innovative technologies and control loops are readily available to measure these attributes and assist operations to improve productivity and mine site profits. The size of the tangible benefits, which can flow from measuring and optimising fragmentation and blast movement, provide a remarkable return on the investment. Realising these benefits needs a focus outside conventional operation silos as a successful Mine-to-Mill project requires a multidiscipline approach across all the silos in the value chain. Required technologies are available; adding the necessary ingredients of communication and co-operation by all concerned across the silos will ensure the benefits are realised.

Nov 8, 2021

Filter Presses are used in a wide range of process industries where high quality filtration at elevated pressure is required. This is mainly due to the fact that modern presses are fitted with polypropylene filter plates which combine excellent corrosion resistance with high mechanical strength. Filtration pressures of 15 Bar at ambient temperatures are common ensuring low residual moisture content and easily manageable filter cakes. Recessed polypropylene chamber plates have been in use for the last 15-20 years and have replaced plates and frames almost entirely. The latest development in plate technology is the polypropylene membrane plate. These provide lower moisture content cakes at significantly higher capacity than recessed chamber plates. Because of their stayboss-free construction, membrane plates provide excellent cake washing facilities which make them suitable for a wide range of process applications. Membrane plates are available both as fixed and exchangeable membrane types. Overhung membranes can be fitted to existing plates manufactured in cast iron or plastic to enhance the performance of existing presses.

Jan 1, 1989

By Rowe J

The case study is based on the largest ore deposit at Mt. Lyell; the Prince Lyell deposit, comprising a regular lensoid mass of dissemina- ted and vein pyrite-chalcopyrite mineralisation. Reserve estimation employs conventional techniques, based on diamond drill hole and relevant development sampling data. Probable ore reserves are estimated using the contouring (isoline) method an longitudinal projections for ore thickness and accumulation (m %Cu) at a '0.8% Cu' cutoff. Final stope and pillar res- erve estimates (proved ore) are derived from designed ring tonnages and contoured accumula- tion for individual mining units, following more intensive sampling. Systematic grade control procedures have been adopted and individual stopes and pillars reconciled against mill production. The proved ore estimates have been found to com- pare favourably with the reconciled production.

Jan 1, 1979

By B J. Beven, A Vatandoost, J Young, S Campbell-Hardwick

The intrinsic value of iron ore depends on its physical and chemical characteristics. For example, silica and alumina are unwanted elements, downgrading iron grade and adversely affecting high temperature processing, attracting penalties in smelter contracts. For this reason, an informed knowledge of processing characteristics and product quality of the ore is valuable and cost effective during mine planning and processing.Ore variability is a significant factor that affects metallurgical behaviour and efficiency of ore processing equipment. Ore of sufficient chemical and physical quality needs to be modelled, mined, processed and usually blended. Feed and product assays are commonly used to assess potential ore upgradability. However, assays alone cannot be all informative of actual processing response given the variability of the physical properties of the ore.This study investigates the potential benefit of implementing a geometallurgical approach during the commissioning stage of the Kings deposit, part of the Solomon Iron Ore project in Western Australia. Kings drill hole database information, ie geological, textural and geochemical data, together with the results of metallurgical test work were used for geometallurgical analysis and modelling. Three main ore types were identified at Kings, namely channel iron deposit (CID), bedded iron deposits (BID) and Detrital Iron Deposit (DID). Additional classifications were utilised to better characterise these units in terms of their physical properties.Bulk sampling for each ore type was carried out across the deposit for metallurgical testing. Multivariate statistical models were developed for prediction of product quality for each geometallurgical unit. A new approach for modelling yield based on ore upgrade factors is introduced. These models were then applied to the Kings regularised mining model to assess product quality across the mining blocks and to plan product stockpiling and blending strategies.CITATION:Vatandoost, A, Beven, B J, Campbell-Hardwick, S and Young, J, 2013. A geometallurgical approach for iron ore product evaluation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

The paper will review the marked upsurge in the installation of new continuous metal coating lines, both hot dip and electrodeposition. Although some of this new capacity has been replacement for obsolete facilities or directed at traditional markets, eg building products, consumer durables etc, by far the major portion is targeted at the automotive industry. The reasons for the rapid growth of coated automobile panels are discussed. A comparison of the installed capacity with projections for this market indicate that a severe over-supply situation has arisen. Many coatings are now available for the automotive industry, each with their own strengths and weaknesses, but none as yet wholly satisfactory. Coating development has mainly been cost driven. This favours hot dipped coatings, providing surface quality and pressing problems can be overcome. The high cost per unit thickness of electrodeposited coatings has also seen pure zinc coatings being replaced by thinner, more corrosion resistant alloy coatings such as zinc-nickel and zinc-iron. Recently resin overlays have been introduced to improve the performance of electrodeposited coatings. Developments in coatings for the more traditional markets will be described. The fastest growing market in the last decade has been prepainted product for the building industry. This has led to the installation of extra painting capacity and again it appears an excess capacity situation has occurred. Over the same period the traditional zinc coatings have continued to lose market share to the zinc/aluminium alloy coatings, Galvalume and Galfan. These have been joined recently by '1'aiyo Crack-Free which has been taken up by some metal coaters. Galvalume is now widely accepted as being the best available coating for unpainted applications. It is also suggested that 'spin-off' coatings from automotive developments might find a niche in the consumer durable market. The end users of coated products, particularly the automotive industry, have demanded improvements in quality, such as surface smoothness, formability, etc. At the same time the new coating lines have to process wider strip and run at faster speeds. To reconcile these somewhat incompatible needs has required numerous process improvements, many of which need in-line instrumentation and computer control. The more important of these changes are discussed briefly. Finally the paper will describe the recent developments which have occurred in continuous galvanising in Australia and put them into context with the rest of the world.

Jan 1, 1993

By Andersen AK

As part of a research program sponsored by Continental Copper and Steel Industries, Inc. (cos), investigations have been conducted by the Colorado School of Mines Research Foundation, Inc. to study the effect of high current densities on electrolytic processes. The importance of high current densities has long been recognized, particularly in the deposition of copper, and the results of considerable research on the subject have been reported in recent years (19 29 39). This is not surprising because, besides plant capacity, current density is the other major factor which will determine the process economics. In the production of electrolytic copper, current efficiency, steam consumption, number of cells, building area, metal inventory, cathode purity, and power consumption are all affected by current density. The ability to maintain a high current efficiency and satisfactory cathode purity while increasing the current density to twice or three times that commonly practiced could result in considerable saving of capital investment and reduce the operating cost per ton of metal produced. The optimum current density i.e., that current density of which production cost would be at a minimum, can be established from an analysis of the various inter- relating factors (49 59). A review of.all operating electrolytic plants (electrowinning and electrorefining) will indicate that most of these plants are operating at 50% or less of the optimum current density (6). One of the reasons for not using the optimum current density may be attributed to the fact that conventional electrolytic tank- house equipment does not perform satisfactorily at high current density operations. Various investigators (19 79 8) have attempted to overcome this limitation by modifying the design of the electrolytic cell, virtually unchanged since it was first introduced in the late 1800's. Previously, these attempts have not resulted in,a cell design suitable for commercial application. However, recently, a cell has been designed which performs efficiently under such conditions. This is a CCS development (patents applied for).

Jan 1, 1969

By M Wen, J Gerit, C A. Pelletier, D Muggli

On-land waste rock dumps at BHP Billiton Base MetalsÆ Island Copper Mine (ICM) near the northern end of Vancouver Island, B.C. continue to discharge ARD. These waters, which amount to approximately five million cubic metres each year, are injected into a three-layer, meromictic pit lake for treatment. The top layer is brackish water, replenished by each yearÆs rainfall (amounting to nearly 2 m/year). This top layer of water must meet effluent permit limits for heavy metals. This water eventually exfiltrates through a æbeachÆ waste rock dump, which is 93 per cent submerged along the north shore of Rupert Inlet. The middle and bottom layers of the Pit Lake are saline and currently oxic (2 mg/L dissolved oxygen) and anoxic (0.03 mg/L dissolved oxygen), respectively. Spreading of a liquid fertilizer every ten days throughout the top layer results in plankton and bacterial blooms that scavenge zinc, copper and cadmium out of this layer eventually to become mineral sediment in the bottom of the pit lake. Adsorption on planktonic skeletons and mineral precipitates also scavenges these dissolved metals from the middle and bottom layers to form bottom sediment. Sulfate reduction has recently begun in the bottom sediments. Diagenetic processes in the bottom sediments will eventually transform most of the dissolved heavy metals into insoluble sulfides. Cycling of ferric iron between the sediment and the water column and back seems to contribute dramatically to the biogeochemical metal removal processes. This biogeochemical system serves to maintain the top-layer water well within permit limits for discharge to the environment.

Jan 1, 2003

By Moritz P

Thiourea has been recognised for a long time as an acid-stable complexant for gold. Generally, the use of thiourea has been shown to exhibit enhanced leaching kinetics compared to cyanide but suffers the disadvantage of excessive reagent consumption. Thiourea leaching is particularly com- patible with the extraction of gold from refractory ores. This is due to the need for an oxidative pretreatment to liberate the gold. Such pretreatments typically result in the production of an acidic residue. The application of novel thiourea leaching technologies to the extraction of gold from a bioleached pyrite concentrate was investigated. The interac- tion of leach variables with thiourea consumption and gold extraction was established. An economic assessment of thiourea leaching was compared with conventional cyanidation. The results indicated that gold leaching of the bioleached residue using thiourea compared very favourably with cyanidation.

Jan 1, 1991

By M Haest, S Sandler, R Botha, H Lang, K Hume

Benchmark practices in the mining industry include the establishment of Quality Programs — Quality Assurance and Quality Control (QAQC) — to monitor the correct execution of sampling protocols and control each stage of the ‘Sample Cycle’: Sample Collection, Preparation (comminution) and Analysis. QAQC reports commonly include statistical-numerical results that quantify performance of QAQC controls (field duplicates, preparation duplicates, blanks, standards etc). Graphics such as scatter plots, QQ plots, histograms and cumulative frequencies are used to represent the results. Statistical values including relative difference, absolute difference, relative variance, averages, T-test, and Zscores are used to quantitatively express the relationship between duplicate pairs ... but is an effective quality program just a statistical exercise? This paper aims to highlight the concept of ‘Quality Management’ (QM) as the precursor of continuous monitoring (ideally in real time) of QAQC results on Exploration, Production, Processing and Port samples, determined by trend analysis performed on a time and/or grades basis. Currently, there is a paradigm in the process of quality assurance that if individual data points fall within a predetermined acceptance limit then they are ‘acceptable’ and therefore suitable for informing operational and investment decisions. However, what is stated with respect to QM is that sometimes results found within the acceptance limits can indeed be internally biased, or show material deviations over a period of time, thereby impacting reconciliation results and/or potentially creating discrepancies with the final buyers. QM refers to the proactive detection of these ‘anomalous tendencies’, the approach and communication with the source of the information, the understanding of the reasons that cause the deficiencies, and the generation of agreed action plans to remediate the situation and ensure the consistency of results, in other words: continuous improvement on proactive manners.

Mar 22, 2022