Search Documents

By D J. Williams, S Islam

Fine-grained coal tailings slurry undergoes only limited settling and self-weight consolidation, and tends to remain slurry-like and unsuitable for conventional laboratory consolidation testing. In addition, constant rate of loading consolidation testing is more representative of the continuous disposal of tailings slurry into a tailings storage facility (TSF) than conventional step loading. The laboratory consolidation testing of coal tailings slurry under a constant rate of loading has been carried out in a purpose-built, large-scale, slurry consolidometer, instrumented with load cells and pore water pressure (PWP) transducers. In the slurry consolidometer, the rate of loading may be varied to represent the actual rate of rise of the tailings in the TSF. A slow rate of loading increases the test duration, while too fast a rate of loading may build up very high excess PWP, without achieving significant consolidation. For the particular fine-grained coal tailings slurry tested, the rate of loading in the slurry consolidometer is varied to access its effect on the development and dissipation of excess PWP. The resulting consolidation parameters are evaluated and explained using the recorded settlement and PWP data.CITATION:Islam, S and Williams, D J, 2018. Optimisation of constant rate of loading slurry consolidometer testing of fine-grained coal tailings, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 72–80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By T Craske, J Sykes, T C. McCuaig, M Jessell, A Trench

The prevalent strategic approach in the mining industry is one of planning. However, it is widely recognised that planning does not work in complex and uncertain situations (Mintzberg, 1994), such as those associated with ‘above ground’ non-technical orebody complexity (Trench, Packey and Sykes, 2014). Mintzberg, Ahlstrand and Lampel (2009) suggest the focus instead should be on strategic ‘thinking and doing’ and using the many ways to think about strategy to make sense of complex, uncertain, and unique situations. They therefore place great value in cognitive flexibility. Scenarios development utilizes several different thinking styles and thus assists with this type of flexible strategic thinking (Figure 1). The ‘Centre for Exploration Targeting (CET) Scenarios’ were developed with the ‘Oxford Scenario Planning Approach’ (OSPA) (Ramírez and Wilkinson, 2016). The OSPA aims more to improve the thinking skills of decision makers, rather than forecasting per se (Wack, 1985a, 1985b). As such, this paper focuses less on the content of the scenarios and instead on the practical value of scenarios in strategizing. CITATION: Sykes, J, Trench, A, McCuaig, T C, Jessell, M and Craske, T, 2018. Strategic thinking about long-term ‘above ground’ orebody complexity using scenarios, in Proceedings Complex Orebodies Conference 2018, pp 60–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By D Anderson, W Timms

"A geotechnical centrifuge can characterise and model the interaction of tailings and fluids over very long time periods by accelerating drainage and consolidation processes. This technology can be considered an environmental ‘time machine’ for designing and evaluating tailings storage projects and verifying numerical models. The Broadbent G-18 geotechnical centrifuge (2 m diameter, up to 875 rev/min) and associated equipment is a unique facility commissioned in 2011 at UNSW Australia for applied research in low-permeability materials such as mine tailings. Two centrifuge modules are available: the permeameter module for characterisation and physical modelling and the strongbox module for physical modelling.This paper presents examples of geotechnical centrifuge applications for the: consolidation of slurries and dewatering design of earthen barriers compatible with tailings chemistry prediction of contaminant mobility. The specifications and capability of the UNSW Australia geotechnical centrifuge and associated instrumentation is also presented, along with preliminary analysis of the confidence intervals associated with permeability testing of a set of samples of varying heterogeneity. Drainage velocity through a mine tailings sample increases linearly with g-level in the centrifuge permeameter until tailings consolidation occurs. Alternatively, geotechnical centrifuge experiments can be designed to limit consolidation so as to quantify permeability changes that may occur with geochemical interactions between fluids and mine tailings or earthen containments. Reactive solute transport through mine tailings can be simulated at realistic solid:liquid ratios when chemical equilibrium is maintained during geotechnical centrifuge testing. Carefully designed physical models of tailings disposal tested at accelerated gravity can therefore provide a realistic evaluation of tailings consolidation and drainage and the potential for subsurface migration of contaminants from mine tailings over long time periods.CITATION:Timms, W and Anderson, D, 2015. Geotechnical centrifuge technology for characterising the interaction of tailings and pore water over decadal time periods, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 247–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By J G. Shellnutt, Y Iizuka, T W-Y Hsia, T-C Liu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of magmatic oxide ore deposits hosted in chemically-evolved layered gabbroic intrusions is attributed to a variety of petrological processes, but there is little to no consensus on the general applicability of each model. Complicating the matter further is that many layered gabbroic intrusions are spatially and temporally associated with alkaline A-type granites, suggesting that there is a petrogenetic relationship between the two types of chemically different rocks. Our experimental results show that petrological modelling using a starting composition of high-Ti basalt from the Emeishan large igneous province can produce evolved silicic liquids that resemble the compositions of microgranular enclaves from the syenitic unit of the bimodal, oxide ore-bearing Baima igneous complex. The experimental results confirm that bimodal gabbro-granitoid complexes can form from a common parental magma and that early crystallisation of Ti-rich magnetite can explain the formation of the oxide ore deposits in the lower parts of the layered gabbroic intrusions. We conclude that crystallisation of a typical high-Ti basaltic parental magma can produce world-class giant magmatic oxide ore deposits and that the occurrence of some alkaline granites may be an indicator of their presence.CITATION:Shellnutt, J G, Hsia, T W-Y, Liu, T-C and Iizuka, Y, 2015. Cogenetic formation of the peralkaline syenite and oxide ore-bearing layered gabbroic intrusion of the Baima igneous complex, Emeishan large igneous province, south-west China , in Proceedings PACRIM 2015 Congress, pp 317–324 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By R Steven

"Surveying, and as a result, surveyors, have been around since the start of time, and it has been said that so has their methodology!The theodolite and tape have been the backbone of a time-tested practice that has led to ground breaking advancements such as electronic distance measurement (EDM), global positioning system (GPS) and positional laser scanning. However, it was the introduction of the unmanned aerial system (UAS) that has allowed mine sites such as St Ives to take the next step towards truly turning survey data into metadata.This paper will explain how the unmanned aerial vehicle (UAV) was adapted to meet the requirements of a mine site supporting a major open pit operation, and how the open pit mining team adjusted their planning and production processes to maximise use of the extra data and information available to them.The advantages of the system include point cloud surveys with corresponding large-scale up-to-date photography and computer generated high detail contouring of mined areas that are then incorporated into the mine plan. All the while, the use of the UAV must be tailored to each specific problem encountered and a solution then matched.Citation:Steven, R, 2016. Trials, Tribulations and Triumphs of Unmanned Aerial Vehicle Surveying at St Ives Gold Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 170–184 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By M Zanin, E Chan, D Xu

An experimental design has been developed to investigate the relative influence of distinct pulp and environmental properties on froth stability in the flotation of a typical porphyry copper ore. In particular, factors such as frother and collector type, feed particle size (P80), solids per cent, composition (chalcopyrite and pyrite content), as well as grinding environment (mild steel versus stainless steel, high and low pH) have been varied in a controlled manner, and the resulting froth stability evaluated. A previously developed froth stability column, based on the Bikerman approach, was used to measure the froth height and half-life in each test. The relative effect of each factor is presented here on a comparative basis. It is shown that frother type is the most important factor, with marked difference in froth stability when switching from methyl isobutyl carbinol (MIBC) to glycol based frothers. Solids per cent and particle size also play a significant role. The grinding environment had lesser effect on the resulting froth stability, although mild steel grinding gave higher froth stability compared to stainless steel grinding. The experimental evidence supports the hypothesis that in porphyry copper flotation the grinding environment influences surfaces oxidation, pyrite activation and the extent of hydrophobic particles reporting to the froth phase. This has an indirect effect on the resulting froth stability, which is however small if compared to the other factors. This work is still in progress, and extension to other mineral systems is planned. However, some insights are offered to operators on the parameters which are more likely to have an impact on froth stability in copper flotation plants.CITATION:Zanin, M, Chan, E and Xu, D, 2014. Empirical evaluation of factors affecting froth stability in copper flotation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 193–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By J White

The Eyre Peninsula (EP) has been known for its iron ore for more than a century. Edward John Eyre noted the ironstone outcrop at what is now Iron Knob in the 19th century. Sir Douglas Mawson visited and reported on the geology of the lower EP in 1906, noting the widespread presence of iron stone and the likelihood of copper being associated with the iron stone. Despite this knowledge there has been only one successful iron ore mining region developed on the EP and that is Iron Knob and the Middleback Ranges which have been mined continuously since 1899. The Middleback Ranges can justly lay claim to be birth place of the Australian iron ore and steel industries.The discovery of large scale haematite resources in Western Australia meant that there was no need to seek out iron ore that needed benefi ciation. The low price of iron ore precluded further development of the EP and many other areas in Australia and overseas. This situation changed rapidly in the mid-2000s with the emergence of China as the world’s industrial power house and the soaring demand and price for many resources including iron ore. This triggered a flurry of activity across Australia and led to the rapid exploration and drives to develop the EP iron ore. A brief examination of the magnetic maps of the EP shows the wide spread presence of magnetite and associated smaller haematite deposits. A closer look reveals the magnetite deposits to vary in formation style and host rock lithology as well as being significantly altered by regional metamorphism. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011

By D E. Thorp

The mining and concentration operations of New Zealand Steel have been carried out initially from the Waikato North Head (WNH) deposit since 1969 and subsequently from the Taharoa deposit since 1972. Over the years the WNH operation has produced about 1.2 million tonnes of concentrate which has been converted into steel, while total exports to the Japanese Steel Industry from Taharoa reached five million tonnes in February of this year. Recent expansion plans both in domestic steel production and in the ironsand concentrate export market have made it necessary for the company to look closely at, among other areas, the mineral processing of the titaniferous ironsands in both deposits. This paper deals with the recent test work carried out at WNH and Taharoa on the use of the cone concentrator unit as a primary gravity concentrating unit ahead of the magnetic separation stages and as a cleaner concentrator following the primary magnetic separation.

Jan 1, 1977

By É Lèbre, G Corder

The circular economy concept, as defined by the Ellen MacArthur Foundation (2015) and quoted by the recent International Council on Mining and Metals (ICMM) Guide to Responsible Sourcing, calls for shifting industrial systems from a linear take-make-waste model to a circular model (ICMM, 2015). In this model products are designed to optimise product and material recovery and reuse, and by-products of one system are used as inputs into other product systems. While the mining industry to date has made a limited contribution to the circular economy, the current market conditions, which are prompting calls for greater innovation, make the timing right for the industry to boost its contribution by utilising and generating value from mining waste, or making it available as a feedstock from which other industries can harness value.The first part of this extended abstract discusses the way the circular economy concept can be adapted to metal mining activities, contributing to a more sustainable resource extraction at the mine site level. The second part of this extended abstract presents a circular economy based framework revolving around non-renewable resources conservation. The third and final part examines the application of the framework to the Mount Morgan mine in Central Queensland.CITATION:Lèbre, É and Corder, G, 2016. Utilising mineralised mining waste – contributions to the circular economy, in Proceedings Life-of-Mine 2016 Conference, pp 132–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

By A B. Jahed, Ö Aydan, T Ito

In this study, the authors compiled some case history data and present some typical examples of rock slope stability issues in Afghanistan with a special emphasis on Kandahar region and categorise rock slope failures according to the principles of modern rock slope engineering. The slopes considered involve rock-cut, natural rock slopes mainly. The effect of structural geology and discontinuous nature of rock mass on both slope-cuts and natural rock slopes is taken into account and some preliminary assessments on the stable and unstable rock slopes are presented. Furthermore, the seismic effect on their stability is also considered. It is also pointed out that similar issues could be observed in open pit mines, which may be exploited in years to come.

Nov 29, 2022

By S Pradhan, A Kuras, R Mahajan

This paper describes the design of the precast concrete segmental lining for the 13.1 m internal diameter and 450 mm thick, 2.4 km long mainline tunnels for the Waterview Connection project in Auckland for the New Zealand Transport Agency.The design and detailing of this segmental lining presented some noteworthy challenges, including an alignment that has sections of low cover in soft ground. Key points of interest are that this precast segmental lining is the largest to ever include steel fibres as the primary method of reinforcement and the lining includes cams on circumferential joints to control ring deformation.The paper describes some of the key design decisions that were made in a collaborative manner with the construction team, tunnel boring machine manufacturer, segment manufacturer and the designers.CITATION:Mahajan, R, Kuras, A and Pradhan, S, 2014. Design of segmental lining for Waterview Project, Auckland, New?Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 289–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The discovery since 1990 of four major orebodies in the Mt Isa Inlier - Century Zn-Pb, Osborne Cu-Au, Cannington Pb-Zn and Ernest Henry Cu-Au - only serves to enhance the already high stature of the Inlier in world mining importance. Currently the known mineral resources of the Inlier represent about 11 per cent of the world's Pb-Zn resources, five per cent of the world's Ag resources, and one per cent of the world's Cu resources. More can be expected to be added to these impressive figures given that two-thirds of the Inlier remains obscured by younger cover. Individually, projects such as Century and Cannington may ultimately achieve `world's best' status; Century's proposed production of 450 000 tpa of Zn metal would rank it close to number one with Cominco's expanded Red Dog project in Alaska. Cannington, with projected production of 660 tpa Ag, could become the world's biggest producer of silver. For comparison, Mt Isa produced 170 000 t of zinc metal and 335 t of silver in 1995. The apparent physical diversity of deposits in the Mt Isa Inlier is matched by a great diversity of opinion as to their origins. Because Ernest Henry is hosted by `porphyries', it is described by some as a porphyry copper deposit, despite mineralisation age possibly post-dating volcanic age by 200 Ma. Cannington Pb-Zn could be a Broken Hill-type (BHT) exhalitive deposit, or a late epigenetic replacement `regional skarn'. Mt Isa - Hilton Pb-Zn deposits appear to have experienced all deformational events and he syn-diagenetic in origin, or may have experienced little of the above and be epigenetic replacement deposits formed late in the major Isan orogeny, some 150 Ma after deposition.

Jan 1, 1996

By T Walsh, S R. Mudnuru

The development of lithium-ion batteries, coupled with the global trend towards electrification of transportation, has led to a dramatic increase in the demand for lithium. The production of lithium from hard rock ores is increasing, and flotation has proved to be an effective means for the beneficiation of many pegmatitic lithium ores. Clariant Mining Solutions has developed a range of novel collectors for the flotation of spodumene and other lithium ores, and this paper presents examples of some of the most recent developments. Fatty acids are the typical collectors for lithium flotation, however the grade and recovery achieved with these collectors is often below the desired level. There are also some significant drawbacks associated with the use of fatty acid collectors, such as the formation of calcium soaps which give rise to filtration problems and the need for acid washing. Several FLOTINOR products have been developed as alternatives to fatty acids. These products offer equivalent or better metallurgical performance at significantly lower dosages than fatty acids. This offers benefits to the flotation circuit as well as potentially reducing the issues associated with downstream processing of the concentrate.

Aug 24, 2022

By H R. Pein

"The Corridor Sands deposit is situated approximately 190 km north east of Maputo, Mozambique adjacent to the paleo-mouth of the Limpopo River. This deposit is one of the worldÆs largest known economically viable resource of titanium, accounting for approximately one third of the global resource. As part of the pre-feasibility and feasibility study for development of the Corridor Sands project, various geological and geotechnical investigations were undertaken, selected results of which are presented in this paper. These investigations have enabled a detailed understanding of the material characteristics of the orebody as well as the tailings materials, such as the fines, to be developed. These material characteristics have had a significant impact on the selection of the mining and disposal methods currently being implemented."

Jan 1, 2001

By L Basnayaka, N Subasinghe, B Albijanic

"It has been recognised that the presence of clay minerals in ores adversely affect flotation performance. In this study, changes in rheological properties of the flotation pulps under normal operating conditions were studied with additions of bentonite and kaolinite clays at various concentrations. Zeta potential measurements were also carried out to determine the changes in surface charge due to adsorption of clay particles. The results showed that bentonite clay adversely affects floatability of pyrite while kaolinite clay had a lesser influence on flotation of pyrite. The addition of Ca2+ ions to the pulp containing bentonite modified the rheological characteristics and in turn improved the pyrite flotation. It was also observed Ca2+ ions suppressed the swelling properties of bentonite and altered surface charge properties of bentonite clay particles. It has been shown that the flow index affected the ultimate recovery and it may provide a means to monitor flotation performance in routine plant operations.Citation:Basnayaka, L, Subasinghe, N and Albijanic, B, 2016. Effect of Clay Rheology on Flotation of a Refractory Gold Ore, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Q Fan

The steelmaking desulfurisation plays an important role in coal-based steelmaking route of blast furnace and BOF converter within the flow sheet of BF-deS-BOF. With the advent of H2-based ironmaking and steelmaking process, the transition flow sheet of DRI-Smelter-BOF has been assessed and developed by the steelmaking industry. What is the role of deS in H2-based route of DRI-smelter-BOF? This paper will present the influence of sulfur-containing iron ore on steelmaking desulfurisation and the leading role of EAF-smelter played in H2-based steelmaking route. The sulfur contents of iron ore vary considerably around the world and lower-grade iron ores with high sulfur are likely to be used for H2-based route, a considerable amount of sulfur that comes from DRI will report to the melt of EAF-smelter and the operating conditions of EAF-smelter also impact the sulfur content of the hot melt for steelmaking deS. The EAF-smelter of H2-based route is the focus of the steelmaking industry at moment, unfortunately, an industrial-scale EAF-smelter has been the missing link of the flow sheet of DRI-Smelter-deS-BOF, despite similar EAF-smelters being used for various applications of Fe-Ti and Fe-Ni processes. The latest progress is that several pilot-scale and industrial-scale EAF-smelters with reducing capability are planned for construction within next several years and low-grade Australia iron ores are certainly to be employed as basic feedstocks for H2-based route of DRI-Smelter-deS-BOF.

Sep 18, 2023

By A Duran

When dealing with rocks in the geotechnical profession, a common activity involves providing an estimate of the intact strength. The tactile approach and descriptions of strength that apply to soils is well documented, can be readily checked through the use of a pocket penetrometer and are known to provide reliable estimates of strength. Moreover, although different soil strength classification systems are present, the bounds between classification classes are compatible across almost all documented classification systems. However, this is not the case for rock strength materials. There are numerous systems within the literature, some with different concepts, and almost all have different bounds to each strength classification. In this paper, the author presents seven classification systems for estimating intact rock strength and highlights issues in their implementation. Example cases are presented to discuss the typical concerns confronting field strength estimates.CITATION:Duran, A, 2014. Comparison of field estimated strengths, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 101–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By W Y. Kim, Y B. Kang, Y J. Park

The phase equilibria in the Al2O3–TiOx system were investigated in wide ranges of temperature and oxygen partial pressure: 1300~1600°C and 10-16.6~10-8 atm, respectively. The equilibrium phases and their compositions were identified using X-ray diffraction (XRD) and electron probe microanalysis (EPMA), respectively. Most noticeably, a wide range of pseudobrookite solid solution was found in equilibrium with almost pure alumina. At each temperature, the cationic ratio expressed as RTi = nTi/(nAl + nTi)) of the pseudobrookite solid solution showed a noteworthy dependency on the oxygen partial pressure. This resulted in the formation of a broad range of pseudobrookite solid solutions, ranging from Al2TiO5 (RTi = 1/3) to Ti3O5 (RTi = 1.0). Complete miscibility within the pseudobrookite solid solution was observed at 1600°C, with only a minor miscibility gap becoming evident below 1500°C. Based on the results obtained in the present study, the behaviours of Al2TiO5 pseudobrookite have implications in two key domains: (1) understanding changes in the physical properties of the materials, and (2) elucidating the evolution of Al–Ti complex oxide inclusions in liquid steel which can deteriorate the steel cleanliness.

Aug 21, 2024

By P Swart, A Fletcher, P D. Erskine

Glencore Coal Assets Australia (GCAA) operates five coalmines in Queensland and has rehabilitated thousands of hectares of mined land across these sites. Accordingly, GCAA seeks to continually improve rehabilitation outcomes over time and work towards progressive rehabilitation sign-off. The ultimate test of rehabilitation success is the attainment of an agreed land-use target, whether for biodiversity conservation or some type of agricultural production, and the ability of the rehabilitated landscape to resist degradation and retain desired functions (eg biodiversity protection or grazing productivity). However, success must be based on documented evidence that can demonstrate adequate progress towards rehabilitation targets and is assessed at appropriate intervals. To assist this task, a stepwise decision guide for the GCAA monitoring program was developed to ensure consistent monitoring data is collected across the range of sites. This presentation will discuss some of the processes that were followed to allow GCAA to identify appropriate metrics to assess rehabilitation success efficiently over thousands of hectares.CITATION:Erskine, P, Fletcher, A and Swart, P, 2016. Preparing for progressive mine rehabilitation sign-off in Queensland, in Proceedings Life-of-Mine 2016 Conference, pp 148–150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016