Search Documents

The paper continues an account, begun in a previous paper, of experimental work carried out by the author whilst a member of the metallurgical staff at the Cockle Creek Works. The general method of the description of the plant and works practice adopted previously has been followed.The paper is a short account of the methods used in and the results of an investigation of the fume losses from the various parts of the plant.MEASUREMENT OF VOLUMETwo independent methods were used. The first depended on a number of pitot-tube measurements of velocity. These readings were taken in the stacks leading from the various furnaces at a considerable height above the ground so as to obtain as regular conditions as possible at the points where the readings were taken.Three openings were made in each stack and the pitot tube inserted into each opening in turn and readings taken at the centres of imaginary areas of equal size. The average velocity in the stack was thus obtained.After four tests had been made at the smelter stack, which removed the gases from all blast furnaces in use, the centre of velocity of the gases for each test was calculated and was found to be practically constant in position. The previous procedure was varied in subsequent tests on this stack by taking a succession of readings at the centre of velocity instead of at various points...

Jan 1, 1925

During the past three years Lurgi's Circulating Fluid Bed (CFB) technology has been successfully applied to roasting of refractory gold ores and con- centrates. In comparison with the so-called Stationary Fluid Bed roasting systems, a considerable improvement of gold recovery, to around 95 per cent, has been demonstrated and achieved on many occasions in pilot CFB units and in commercial CFB roasting plants as well. The major reason for such improved gold recoveries is the excellent controllability of the roasting process in the CFB reactor system. Here, temperature, gas atmosphere and solids residence time are more precisely controllable at optimal values during roasting operation in order to achieve the highest possible gold recovery in the subsequent leaching process step. Further dominant benefits of CFB roasting systems are their flexibility with regard to feed material, throughput capacity, dry or slurry feed, almost unlimited oxygen enrichment, direct fuel addition and in situ capture of SO2 in the presence of limestone and dolomite. The system will accept 50 per cent turndown ratio, large variations in feed composition and particle size, as well as a variety of different fuel types. The commercial applications of CFB roasting systems for gold con- centrates have been realized so far at Fimiston, Kalgoorlie/Westem Australia and for whole ores at Cortez, Nevada/USA.

Jan 1, 1991

By J H. J Holtzhausen

Never has there been more focus on the health, safety, and well-being of our employees at the workplace. Ever evolving expectations of individuals, companies and clients are shaping regulatory reviews and advancing standards across the world in the drive to zero harm. The technology is advancing at a rapid pace, which is now allowing continuous real-time monitoring of contaminants to take place in the harshest of environments.

Oct 12, 2022

By P C. Hagan, J Chen, S Saydam

Fully grouted cable bolts have been used in underground mining industry for more than 40 years and are becoming more and more popular especially when severe geological conditions are encountered, such as high stresses and large cross-section excavations. The axial performance of cable bolts are mainly relied on the load transfer process between the cables themselves and surrounding rock masses via grout annulus. Therefore, the selected grouts play a significant role in determining the reinforcement quality for underground openings. In order to better understand the mechanical properties of Stratabinder HP grout, which is one type of cementitious grouts commonly used in Australian underground coalmines, plenty of unconfined compressive tests are conducted on it. Following diverse standards, two different kinds of samples are prepared and tested with the w/c ratio ranging from 0.35 to 0.45. During the test important mechanical properties including uniaxial compressive strength (UCS) values, Young’s modulus, Poisson’s ratios and so forth are recorded. Based on experimental results, the effect of w/c ratio on the mechanical properties of Stratabinder HP grout is studied. Beyond that, influences of sample size on the failure mode, peak strength as well as residual strength of this kind of grout are summarised and analysed.CITATION:Chen, J, Hagan, P C and Saydam, S, 2014. Mechanical properties of cementitious grout serving in fully grouted cable bolting systems, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 269–276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By M Yvon, S Parkes, K P. Galvin, P Wang

Mineral liberation is critical to maximise the grade and recovery of nickel, however this objective is challenged considerably by the poor flotation kinetics, especially that of ultrafine particles (Kelebek and Tukel, 2018; Multani and Waters, 2019). High recoveries demand long cell residence times and hence a large flotation capital expenditure (Wills and Finch, 2016). However, this leads to excessive entrainment of gangue minerals, thus negating efforts to depress its recovery. This study aimed to investigate new hydrodynamic approaches to improve nickel flotation, focusing primarily on unrecovered nickel from a Western Australian tailings stream. Mechanical cell flotation experiments were conducted to understand the flotation kinetics, covering different size ranges. A novel Reflux Flotation Cell (RFC) was also used to improve the nickel recovery and reject the silicates. Future work aimed at applying the RFC to different size portions is also outlined.

Aug 24, 2022

By S Hancock, B H. Brady, H Muhlhaus

The aims of this paper are to present the governing science, verify the performance and demonstrate the potential engineering applications of a computational simulator for in situ leach mining of non-ferrous minerals. Assuming that the target mineral is deposited either uniformly within rock matrixes (matrix-hosted) or on fracture walls (fracture-hosted), in situ leaching can be treated as reactive flow and transport in geological media (porous media for matrix-hosted ore deposits and fractured media for fracture-hosted ore deposits). Under this treatment, the processes of in situ leach mining for non-ferrous minerals can be quantified through several sets of equations and these coupled equations have been numerically solved. The computational simulator has been applied to the simulations of one-, two-, and three-dimensional in situ leaching cases. The computational simulator, together with laboratory and in situ leaching tests, can be used to:optimise the leaching chemistry; optimise the in situ scale mining operations; scale up the in situ scale test operation to a full-scale mining operation; and evaluate the post-mining environmental restoration plan.

Jan 1, 2000

The long-term outlook Tor Australla's traditional mining products is for flat demand and continuing low prices. This has come about because of three far-reaching changes since earlier boom days: 1. Continuing declines in intensity of usage of basic mine products; 2. The failure of newer western and third world developing countries to realise growth expectations; and 3. Continued production pressure from third world countries (and first-world primary producers) in an effort to earn foreign exchange and rectify trade balances. These trends have led to a general situation of excess supply and weak demand. In this environment, the prerequisites for survival in the mining sector are first-class mines, modern and efficient production methods, low unit costs, aggressive marketing, and products with reasonable operating margins. Many of Australia's mines meet these prerequisites. Following the A$ depreciation and widespread unit cost reductions, most of these mines will be moderately profitable at current depressed commodity prices. They are well placed to benefit from price rises if these eventuate. A new generation of mines is concentrating on a more profitable product range (gold, diamonds, uranium, mineral sands). Australia's balance of trade remains firmly dependent on the primary mining and agricultural industries (Fig. 1). Despite optimistic talk of high-tech developments, tourism and a resurgence of manufacturing, these will remain a small component of Australia's export structure.

Jan 1, 1987

By Y K. Leong

Occasionally additives are used in the wet processing of iron ore tailings and slurries, for examples, in the thickening of tailings with flocculant to recover process water, and in the smooth pumping of concentrated slurries. They can mitigate slurry behavioural issues that could significantly affect the plant operation and production. The nature of iron ore business requiring the plant to have a high throughput to be economical, large amounts of slurries are therefore processed every day. The quantity of additives needed will correspondingly be large and so are the associated costs. This could have a significant impact on the plant profitability. If additives are used they must be very costeffective. NaOH is among the lowest cost chemicals available, at ~US$400 per ton. In this paper we will look at use of composite additives involving phosphate compounds with NaOH added to reduce the cost, for the control of iron ore slurries rheology. The NaOH worked synergistically with the phosphate compounds. The effectiveness of these composite additives in viscosity reduction can be neutralised by another cheap additive such as lime or a Ca(II)-based salt turning the slurries back to being a paste. Tailings paste is an ideal material for safe storage in the dam. These composite additives can also be used to facilitate the recovery of iron ore at commercial grade from tailings (Leong, 2020a, 2021a).

Sep 18, 2023

By Recepoglu O, Tolun R, Yavasoglu N, Bulutcu AN

Scheelite was floated from a low-grade (0.28 per cent W03) calcitic (96.30 per cent CaCO3) scheelite ore using oleoyl sarcosine as collector and alkylated 8-hydroxyquinoline as modifier. Compared to oleoyl sarcosine alone, the grade and the recovery of scheelite concentrate were increased from 8.07 per cent to 33.54 per cent and from 55.1 per cent to 73.4 per cent, respectively. Infrared studies with pure calcite and scheelite minerals showed that while alkyl oxine is adsorbed on the scheelite surface, it is not adsorbed on the calcite.

Jan 1, 1993

By A M. Ebbels

"Underground mine scheduling decision-making has been based on production requirements, equipment productivities and the mine planner’s instincts on the best scheduling strategy for the mine to optimise the net present value (NPV) of a project.In the last few years, innovative software has been developed to optimise underground schedules based on NPV. The schedule optimisation tool (SOT) allows the user to set up scenarios based on grade, metal content, capital and operating costs.This paper discusses the results of two case studies undertaken using the SOT software to optimise the NPV of the projects.In each case study, the SOT software has been applied in two ways:using the original mine planner’s scenario and determining whether the NPV could be improved by changing resource capacitieschanging the scheduling goals to determine whether a different mining strategy would have a better NPV outcome.The outcomes of the case studies demonstrate that the mine layout and design were contributing factors to the overall improvement of the NPV and that SOT has a more noticeable impact on the NPV of projects where less sequence constraints are required, such as geotechnical sequencing and access development.CITATION:Ebbels, A M, 2016. Optimising underground mining strategies, in Proceedings Project Evaluation 2016, pp 60–65 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By A Golsby

Both primary and secondary ventilation is important in underground mining. Secondary ventilation refers to the provision of ventilation to development ends, stopes and services facilities, which constitute secondary circuits tapped off the primary circuit or main through flow of air.An unbalanced primary and secondary combination can cause re-circulation, which is inefficient and potentially hazardous. These inefficiencies extend into operational and other considerations, such as power.Most cost justification analysis covers capital and physical consumables. These analyses are often not comprehensive or holistic. This case study is an example of ‘how to holistically justify’ a secondary ventilation circuit and optimise it to meet all stakeholder needs.This paper particularly addresses the following:how to account for all stakeholders in a secondary ventilation cost justificationthe secondary ventilation componentsthe cost justification outcomes and how to measure themsome of the sensitivitiesthe stakeholdershow to present the justification to meet the stakeholder needssecondary ventilation cost justification.CITATION:Golsby, A, 2015. Secondary ventilation as a value proposition – a case study, in Proceedings The Australian Mine Ventilation Conference, pp 49–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D Giddings, S A. Silvester, S Pickerin

Underground fires represent a constant threat to the safety of underground personnel. Miners in the immediate vicinity may face intense heat, blinding smoke, toxic fumes, fall of ground and other direct effects of a fire. However, the vast majority of victims never actually see the fire, and are overcome either by deadly fumes in the ventilating current or by asphyxiation. The mine ventilation system, which maintains a sustainable atmosphere to the working places, can transport products of combustion with equal efficiency. Miners who are remotely situated from a fire may be forced to evacuate considerable distances, through dense smoke and fumes, or even become cut-off from escape. Additionally, miners may become confused by unfamiliar ventilation characteristics caused by fires. Conveyor belts are widely used for transporting minerals in mines as well as in many other industrial situations. Because they contain large amounts of polymeric materials their use in certain environments, especially coal mines, but also in steel works, power stations and other enclosed areas must be controlled to minimise the fire risk. Over last nine years there have been 60 fires in underground mines in the UK alone and that of these, half have been associated with conveyors. This paper summarises the results obtained from a recent research project that has developed a preliminary computational thermal and fluid dynamic model to represent the spread of flame along a typical conveyor belt used in UK deep coal mines. The results of these models have been calibrated against a series of experimental tests performed within a surface fire test gallery. An improved knowledge of the burn characteristics and rate of release of the products of combustion from conveyor belt fires will assist in the development of better fire detection and fire fighting techniques.

Jan 1, 2005

By F Carrick, W A. Ellis, D R. Mulligan, S I. FitzGibbon

"One of the major environmental impacts of mining is the destruction of habitat. The koala (Phascolarctos cinereus) is an iconic Australian marsupial that has been severely affected by land clearing and its decline is continuing. This has placed pressure upon mining companies and government agencies to ensure koalas are managed throughout the life-of-mines - from land clearing through to rehabilitation of post-mining landscapes. This paper reports on the æKoala VentureÆ research partnership between The University of Queensland and Rio Tinto. As part of the Koala Venture program we examined koala use of two types of restored environments: rehabilitated mined land (20 sites) natural regrowth forests (six sites), at Blair Athol Coal Mine in Central Queensland, Australia. Searches for koala scats revealed evidence of koalas in ten per cent of rehabilitated sites (2/20) and 33 per cent of natural regrowth sites (2/6). Two factors were identified as being of greatest importance in facilitating koala recolonisation of restored habitats. Firstly, all recolonised sites were located close to native forest occupied by koalas (mean 135 m ¦ 52). Proximity to source animals is considered crucial to recolonisation of suitably restored habitats. Secondly, three of the four recolonised sites were dominated by koala food trees, most of which were large enough to be utilised by koalas. Availability of suitably abundant food resources is, therefore, also considered crucial. The requirement for these two factors, in combination, is highlighted by the absence of koalas at several sites that contained abundant food trees, but that were distal to areas with source animals, and vice-versa.Our research demonstrates the enormous potential for restoration of wildlife habitat on post-mining lands, even for species with specific requirements such as the koala. Consideration of the ecological requirements of wildlife during rehabilitation planning is critical to enhancing the likelihood of recolonisation.CITATION:FitzGibbon, S I, Ellis, W A, Mulligan, D R and Carrick, F, 2012. Rehabilitating post-mining landscapes for wildlife - A case study from the Koala Venture research program in Central Queensland, in Proceedings Life-of-Mine 2012, pp 319-324 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By M I. Pownceby, N A. S Webster, A J. Studer, I C. Madsen, J A. Kimpton, M J. Fisher-White, L Lu

In situ synchrotron X-ray and in situ neutron diffraction-based experimentation have been implemented to characterise the formation of the complex calcium ferrite iron ore sinter bonding phases silico-ferrite of calcium and aluminium (SFCA) and SFCA-I. Experiments were carried out using fine-grained (<20 ¦m) sinter mixtures containing ~77 wt per cent Fe2O3, 14 wt per cent CaO, 3.5 wt per cent SiO2 and 5 wt per cent Al2O3, with diffraction data collected during heating until 1300 - 1350¦C, which was enough to ensure complete melting of the SFCA phases. In the case of the in situ synchrotron experimentation, results showed that altering the nature of the starting sinter mixture (ie substitution of goethite for hematite; substitution of an amorphous Al2O3-based mineral for gibbsite) did not have a significant effect on the thermal stability range of the SFCA phases. It did, however, have a profound effect on the formation and rate of consumption of the calcium-rich ferrite phases C2F and CF, and on the formation mechanisms of SFCA and SFCA-I. The in situ neutron diffraction experimentation is the first described in the context of iron ore sintering, and the observation of both SFCA-I and SFCA formation in the in situ diffraction data represents the first step in achieving the goal of charactering iron ore sinter phase formation in large volumes of industrial sinter starting materials with a wide range of particle sizes (up to 6.3 mm).CITATION:Webster, N A S, Pownceby, M I, Madsen, I C, Studer, A J, Lu, L, Manuel, J R, Kimpton, J A and Fisher-White, M J, 2013. In situ x-ray and neutron diffraction studies of silico-ferrite of calcium and aluminium iron ore sinter phase formation, in Proceedings Iron Ore 2013 , pp 487-494 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By K Esmaeili, S Aziznejad

Impact-induced rock fragmentation is a mechanism that is commonly used for rock breakage in drilling and crushing. Additionally, rock fragmentation by blasting is frequently used in rock excavation operations. Experience shows that the presence of discontinuities can significantly influence the impact-induced damage and fragmentation of rock. Quantification of the response of jointed rock masses to impact loads is complicated by the fact that the available laboratory tests are mainly designed for aggregates or intact rocks. It can be argued that neither of these tests adequately represent a jointed rock mass. This paper presents the results of a series of numerical simulations used to investigate the influence of pre-existing discontinuities on the impact-induced fragmentation of rock masses. The methodology includes determination of the static and dynamic mechanical properties of a rock unit by conducting a series of laboratory tests on intact rock samples collected from a quarry in Canada. A 2D distinct element code, Particle Flow Code, was used to generate a bonded particle model in order to simulate both static mechanical properties (uniaxial compressive strength, elastic modulus, Poisson’s ratio and indirect tensile strength) and dynamic mechanical property (drop weight tensile strength) of the intact rock. The calibrated numerical model was then used to construct large-scale synthetic rock mass samples by incorporating discontinuity networks of different intensity into the bonded particle model. Finally, the impact-induced fragmentation inflicted by a rigid projectile particle on the jointed rock mass samples, simulated by a synthetic rock mass model, was determined. More fragmentation was observed for the rock mass samples with higher joint intensity.CITATION:Aziznejad, S and Esmaeili, K, 2015. Effects of joint intensity on rock fragmentation by impact, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 377–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R N. Humphries

The aim of this paper is to question the need to develop bespoke monitoring and assessment methodologies and criteria, thereby ‘reinventing the wheel’, when designing and assessing the success of important natural habitat and ecosystem restoration schemes at mine sites in the UK and Australia. It draws attention to the existence and applicability of the Phase I Habitat, National Vegetation Classification (NVC) and Condition Monitoring methods in the UK and similar approaches used in Australia. These are long accepted established methodologies and have published accounts for describing, assessing and managing natural vegetation communities, habitats and ecosystems. They are often used at the environmental impact stage, but seemingly rarely, if at all, in restoration design and management at mine closure. Their application to mine restoration and closure is illustrated and discussed by reference to a surface coalmine in South Wales, UK.It is concluded that the application of a combination of the Phase I Habitat, NVC and Condition Monitoring methods is highly relevant to the expectations of the Convention on Biological Diversity (CBD) and its implementation in the UK, and probably in Australia too. The methodology and criteria described could be incorporated into the guidance and specified in the mining permits so that there is clarity as to the expectations and requirements for monitoring and assessment for bond release. Their use could be of wider application where there is a requirement to assess the success of restored CBD assets and ecosystems.CITATION:Humphries, R N, 2014. Why reinvent the wheel when there are established methodologies to aid the design and assessment of restored natural ecosystems on mined land?, in Proceedings Life-of-Mine 2014 , pp 675–692 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Toro HCH, Von Borries GH

A brief description of the semi-autogenous grinding (SAG;) facilities of Compania Minera Disputada de Las Condes is given. A data-logging and computer system was connected to the plant inter facing the existing analog control system in a supervisory s, control philosophy. The development of a control straiov,v t,) maintain maximum power of the SAG mill atsubjected to process restrictions is shownThe present control scheme is discussed inalgorithm was designed based on correlations onLween vartaoles. Associated with this, a direct level of control was developed be, on classical control algorithms, process inter-active tuning has been included. Also, an algorithm to prevent overloading of the is discussed. Control scheme tests are presented in comparison t manual operator control under the same conditions. It is shown t the control strategy gives a more stable operation and a higher plant throughput.

Jan 1, 1985

By Griffin PT, Espinosa-Gomez R, Jameson GJ

Two major issues are to be addressed in the Copper Concentrator of Mount Isa Mines Limited. The first of these is the need to increase concentrator flotation capacity to increase copper recovery, while the second is the need to reduce the iron sulphide dilution to meet future smelting requirements. Extra capacity in the cleaner and retreatment sections of the concentrator have been identified as key target areas, with additional copper recovery of at least one per cent identified from plant trials. Extensive pilot plant tests have been undertaken to evaluate the performance of the Jameson cell compared to conventional mechanical cell and column circuits. This work has shown that Jameson cells present an opportunity to achieve the desired grade and capacity specifications at lower capital cost than available alternatives. This paper outlines metallurgical results of work undertaken in the Copper Concentrator, together with a summary of pertinent Jameson cell operating parameters investigated during the period.

Jan 1, 1993

By C M. Stewart, P Bowen

McArthur River Mine, in the Gulf Country of the Northern Territory, exploits one of worldÆs largest deposits of zinc, lead and silver. It was officially opened in September 1995, 40 years after its discovery in 1955. This paper describes the geological, engineering and metallurgical assessments which made up the feasibility study. It then relates how these study components compare with the first two years of operation. The challenges that had to be overcome before the McArthur River Mine became economically viable included the metallurgical problems associated with extremely fine grained ore and the development of an effective mining process.

Jan 1, 1998

By F Saloojee, F K. Crundwell

Refractory ores need to be pretreated prior to cyanide leaching for acceptable gold recovery. Pressure oxidation is one method of rendering the ores more suitable for cyanidation. The focus of this work is optimisation of autoclave configuration for pressure oxidation. An autoclave for the pressure oxidation of a feed containing pyrite and arsenopyrite was modelled, using the population balance framework. The autoclave model takes into account feed particle size, reaction kinetics and retention time. Mass balance calculations were incorporated into Cycad Process« software. This allowed for the investigation of different circuit configurations. The base case model consists of a single autoclave. The feed was then doubled and additional autoclaves were added to provide the same residence time as the base case. Four different configurations for the additional equipment were simulated. These were parallel, series, series with inter-stage thickening and parallel-series circuits. The options are compared in terms of extraction and productivity. The parallel circuit behaves similarly to the base case. The series and series-parallel circuits have higher recoveries and productivities than the base case. The series circuit with inter-stage thickening provides the highest extraction and productivity. This is because the thickening reduces the slurry volume and increases the residence time of the solids in the downstream autoclave.CITATION:Saloojee, F and Crundwell, F K, 2013. Optimisation of circuits for gold pressure oxidation, in Proceedings World Gold 2013 , pp 181-188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013