Search Documents

By Davies B, Rogers A, Grainger A, Todd J, Brenman R, Jones L, Horton B, Eager L

Research into the control of diesel particulates (DP) has been. conducted by BHP Coal for more than 7 years. Personal monitoring of employee exposures (n = 480 full shift samples) conducted at nine underground coal mines has indicated that the exposure of the workforce ranges from less than 0.1 to 2.2 mg/m3 of DP dependent on job type and mining operation. Approximately 50% of the mass of DP captured is elemental carbon (EC) which is the species currently being considered by some international regulatory authorities as the exposure standard. Five technologies for controlling DP were investigated in a combination of studies conducted in an above ground simulated tunnel, in a special controlled section of underground mine roadway and validated by application in standard coal mining operations at Tower Colliery. Tests conducted under controlled conditions indicate that dependent on the type of fuel in use, the introduction of low sulphur fuels can reduce DP levels in return airways by up to 50% and in actual mining situations a reduction of 20% can be achieved in exposure of the workforce. In addition, subjective responses from the workforce indicate that exhaust emissions from low sulphur fuels provide lower irritation and a more pleasant aroma. The use of water filled scrubber tanks reduces the level of DP emissions by 25%. Chemical decoking of engines resulted in a reduction of 20% in DP in return airways. A commercially available non-flammable disposable dry exhaust filter constructed from synthetic organic fibres with an operational lifetime in excess of 20 hours was found to reduce DP exhaust emissions by 80%. Investigations have indicated that the use of increased ventilation to control DP levels particularly in multiple vehicle situations does not follow a simple dilution factor and in some instances compliance with current regulatory requirements may not produce the required reduced exposure levels. The results from single component control strategies provide considerable reduction in exposure to DP, however the most efficient and cost effective control methodology is the use of a combination of individual systems modelled to operations conducted at each mine.

Jan 1, 1998

By M Barley, C A. RosiFre, L Lobato

The Carajßs iron ore deposits contain approximately 17.5 billion tons of ore with >64 per cent Fe and occur in the eastern part of the Amazonas Craton. They are hosted by jaspilitic banded iron-formation (BIF) of the Carajßs Formation which, together with metavolcanic rocks, comprise the ~2.75Ga Grpo Parß Group of the Itacai·nas Supergroup in the ~1000 km long, E-W trending Carajßs Synclinorium. The Carajas Formation comprises discontinuous layers and lenses of partly dolomitised BIF (17 - 43 per cent Fe and 35 - 61 per cent SiO2) and lenses of high-grade iron ore, cut by mafic sills and dykes. The high-grade iron ores occur as large tabular bodies of friable (soft) hematite with smaller lenses of hard (compact) hematite. The hard hematite ores typically occur at the contact with the underlying volcanic rocks and are surrounded by an aureole of hydrothermal carbonate alteration. BIF that has been overprinted by dolomite and magnetite crystallisation has recently been discovered at depth in the N4E Mine. With increasing amounts of carbonate, the original lamination (microbanding) and other fine primary structures in the BIF have been progressively obliterated resulting in alternating carbonate and iron oxide mesobands. The friable hematite ore that is characteristic of the Carajßs deposits results from ongoing weathering and leaching of the carbonates from this type of altered BIF. The hard hematite ores probably result from more extensive early oxidation. The association of both carbonate-altered and jaspilitic BIF with the N4 Mine is similar to that observed at the Mount Tom Price deposit in Western Australia, where carbonate-altered BIF occurs below massive hematite ore with a jaspilitic halo developed above the orebody. This indicates that as at Mount Tom Price, hydrothermal carbonate alteration and associated loss of silica from BIF may be an important step in the formation of these giant hematite deposits.

Jan 1, 2002

The development of the Ballarat goldfield and of the city of Ballarat are a significant part of the history of the Australian mining industry. Important developments in technology, legislation and labour relations made their first Australian appearance in Ballarat. The growth of the city and its survival after the closure of the mines provide an interesting case study in the benefits flowing from a vigorous mining operation. The failure of the mines can be attributed to rising costs of materials and labour and declining manpower productivity at a time when the price of gold was not free to respond to changing market conditions. The curtailment of exploration programs and increasing labour unrest resulted from this situation, and made the closure of mines inevitable.

Jan 1, 1982

One of the most praninent Bouguer anomaly features in the Broken Hill District is the long wavelength high of 10-15 ngals above background which forms a northeast trending, oval zone sane 15 km by 45 km with Broken Hill on its northern gradient. Rock density measurements and modelling indicate that this anomaly can be explained by the presence of generally relatively higher density meta- sediments extending from the surface to a depth of about 2000 m. The regional Bouguer anomaly data show that the Willyama Block and Euriowie Block are mostly overlain by a fairly smooth Bouguer anomaly high in the range 5-15 mgals, whilst the surrounding younger sediment covered areas, including the Mundi Mundi Plain, Murray Basin fringe and Bancannia Trough, are mostly overlain by lows which range to minus 30 mgals. Thus in terms of the gravity pattern the Willyama and Euriowie Blocks form a fairly continuous and haogeneous entity. However, the 5-10 mgals relative low over part of the Torrowangee Synclinorial Zone indicates that the Adelaidean System metasediments are in aggregate slightly less dense than the Willyama Supergroup metasediments. The low can be modelled to indicate a basement link between the Broken Hill and Euriowie Blocks at 1000-2000 m depth.

Jan 1, 1983

By P Stoker

The need for quality assurance and quality control (QA/QC) in the sampling and assaying of minerals is fundamental to the reliability and confidence of a mineral resource estimate, reserve estimate and possibly profitability of a mine. In spite of this, QA/QC practices in the mining industry are commonly applied poorly, or misunderstood. As New Leaders, we should aim to correct the poor practices and become fully informed on appropriate procedures. This paper uses worked examples that show the usefulness and importance of best practice QA/QC procedures. Fundamentals of reviewing the performance of the laboratory by examining the results of client inserted standard reference material (standards), blank material and duplicate samples are discussed. To do this, three examples from Australian data sets have been used. For each example, simple and efficient plotting techniques are suggested with subsequent evaluations of each plot. The first case study compares the results of internal standards from a laboratory with blind standards (where the expected value is unknown to the laboratory) submitted by the client. It was demonstrated over time that the laboratory was unintentionally analysing the internal standards in a different manner to the remainder of the sample batch. In this example, not understanding the cause of a high negative laboratory bias could have led to poor understanding of the depositÆs grade and in the extreme a proposed mining operation may have reached operational stage with a subeconomic grade. The second case study discusses the quality of blank material submitted by a mining operation to monitor cross-contamination within the laboratory. The blank material contained background levels of the element under investigation. This created uncertainty in the assay results, which could have led to the need for additional assays and drilling programs. Finally, the third case study demonstrates the use of the relative paired differences (RPD) technique to cross-validate the results from duplicates and repeat analyses from two laboratories. The three examples given show either laboratory or operational error. If left undetected, each example could have had serious implications for the mineral resource estimate and ultimately, the mining operation. These examples are not isolated occurrences; poor QA/QC practices are an industry wide problem exacerbated by rapid staff turnover and increased contractor positions on-site. New Leaders must be equipped with a thorough grounding in QA/QC best practices to improve its application and confidence in the results of sample analysis.

Jan 1, 2009

By Miller RJ, Eager DT, Lama RD

For safe and efficient mining operations, it is essential that environment and equipment status be monitored. A system that gives quick access to status at any given time, and also permits quick analysis of their history, is required. Such a computer based monitoring system has been installed at West Cliff Colliery.The system is based on 2 super mini computers. Three major sub-systems monitor conditions in the longwall operations, environmental conditions in the intake and return roadways, status of the underground and surface installations, and mining and transport equipment.

Jan 1, 1985

An assessment has been made of six reported methods for the determination of the swelling of iron ore pellets on reduction. The methods are discussed on the basis of apparatus requirements, reduction conditions, sample requirements, measurement of swelling and reproducibility. It is concluded that the CNRM, LKAB, and Lurgi methods are the most satisfactory which presently exist for determination of the swelling of industrially produced, iron ore pellets.

Jan 1, 1974

SOME 70 miles south-east of the of Auckland lies the town of Waihi-the centre of the Waihi goldfield, at present the mining pride of New Zealand. That the glory of most mining camps is evanescent forms an axiom to which it may be expected Waihi will prove no exception. For the last fifteen years, however, Waihi has been an important gold-silver producer, with an annually increasing output, so that now the area ranks as one of the leading goldfields of the world.

Jan 1, 1911

The Late Permian intermediate to silicic talc-alkaline Drake Volcanics of New England, N.S.W., consist largely of shallow marine, redeposited volcaniclastic rocks which host epithermal Ag-Au deposits. Pervasive hydro- thermal alteration is widespread. The 200-300 m Cataract River Member includes several sedimen- tation cycles composed of massive pumice brec- cias, overlain by laminated sandstones and siltstones, interbedded with marine, fossil- iferous mudstones. Two distinct groups of cla- sts exist within the volcaniclastic beds: 1. Lithics of predominantly intermediate compos- ition lavas that have undergone subaerial epi- clastic erosion and transportation; 2.Pumice, quartz and plagioclase crystals which have not been reworked by epiclastic processes. The lithic clasts were derived locally in a sub- aerial environment within the Drake Volcanics, and pumice and crystal fragments from contem- poraneous centres of silicic volcanism else- where in New England, N.S.W. The latter group of clasts was transported to Drake by Plinian airfall or rafting, and fell and was washed on- to emergent portions of the Drake Volcanics, where reworked locally derived fragments occ- urred. Cold state subaqueous mass-flows, prod- uced by slumping, resedimented the mixed vol- caniclastic detritus into the marine basin in a series of cyclic units with massive lower parts, and laminated upper zones. Modern ana- logs of the palaeogeographic setting in New England, N.S.W., in the Late Permian are pro- vided by the Taupo Zone, New Zealand, and sou- thern Kyushu, Japan.

Jan 1, 1987

The discovery of minerals in any community, especially precious minerals, gives a sense of hope and optimism about development prospects within the community. However, the euphoria surrounding such a find could be short lived if the wrong perception is created at the inception of the project, that the exploitation of the mineral resource will pose a serious problem to the community. The socio-economic impact can be negative or positive but if not properly handled, the negatives will outweigh the positives. Illegal mining activity, popularly known as Galamsey in Ghana, is a typical example of the negative impact of the mineral industry. Galamsey activities have resulted in an increase in school drop-out rate, pollution of water bodies affecting entire communities bringing a lot of health problems, destruction of farm lands, destruction of rail lines resulting in transportation problems, armed robbery, prostitution, just to mention a few. The improvement of the water supply system in the surrounding communities, implementation of sustainable development programs, improvement in the infrastructure, are just a few examples of positive socio-economic impact.Factors responsible for the socio-economic and environmental impact include: the unwillingness of most companies to invest substantial resources to deal with environmental issues, lack of adequate professionals with the requisite appreciation for environmental issues related to their activities, realisation that support of surrounding communities is key to successful operations, the now globally accepted view that multinational companies should invest in the socio-economic lives of the surrounding communities, etc. In order to ensure the prevention of the negative impact of mining activities on local communities, there should be a paradigm shift in the way the training for the new crop of mining and metallurgical engineers have been structured in the past, social contract with the local communities must be drawn and implemented; it must not be an imposition on the communities but rather a contract arising out of extensive interactions between the industries and the local communities. Environmental awareness has reached a level where communities affected by the minerals industry, to a very large extent, know what they should tolerate and what they should not. There is therefore the need to ensure that effective systems are in place to exploit mineral resources without damaging the environment.

Jan 1, 2008

A review is given of progress made to- wards the development of personal gravimetric dust sampling for risk assessment on South African gold mines. The present strategy is critically examined on the basis of principles for assessing health hazard from dust exposure. Reasons are advanced for replacing the konimeter with a gravimetric system based on full shift personal sampling. Constraints imposed by local characteristics of gold mines are used to illustrate the difficulty in finding suitable instrumentation for measuring personal exposure to respirable silica.

Jan 1, 1988

Mine reconciliation is the practice of comparing the tonnage and grade of material processed by the mill with the tonnage and grade of ore in the reserve model of a deposit, and with the tonnage and grade in the grade control models used to de

Jan 1, 1998

MANPOWER RESOURCES The optimisation of human effort has been an ongoing and significant process in the coal industry since industrialisation as we know it began. The extent to which the changes sought have been achieved has, over the years, been in the main determined by the economic and political forces existing at that time and the determination and character of the individuals involved. The question of optimisation is therefore not new in our industry. Hopefully this presentation will demonstrate to the reader the effect of previous measures adopted by industry to optimise all facets of its operation and in particular that of the human Resource.

Jan 1, 1991

By Kapoor M. L

EMF measurements were performed in the temperature range of 933-1095 K to determine the thermodynamic properties of oxygen dissolution in liquid lead and lead-tin alloys with tin in the dilute concentration range of 0 to 6 atom per cent. The oxygen in the Pb-O system was varied by equilibrating with (PbO) slag, and that in the Pb-O-Sn system was varied with the addition of lead oxide. Wagner's interaction parameter approach was used to evaluate the self interaction parameter and ternary interaction parameters at different temperatures, to yield: E8(pb) = 97.35 - 113.27 x 103/t Eo(pb) = 139 - 20.616 x104/1' Quasichemical formulation was employed to yield Inf to reveal the effect of tin on oxygen in lead. Results have been predicted on the basis of classical models and those obtained using the QCT approach of Alcock and Richardson at Z=2 have been found to agree with the experimental Data.

Jan 1, 1992

By Pigdon SP, Anderson RM

The production of stabilised backfill at mine sites commonly uses Portland cement as the binder. Calcined gypsum has cementing properties and is cheaper to produce than cement. This paper discusses the strength of fills stabilised with calcined gypsum. Laboratory tests were carried out on specimens prepared from tailings obtained from four different sites to allow for the wide variety of tailings found in practice. The results show that the gypsum-based fills can achieve a strength of I MPa using around two and a half to four times the corresponding amount of cement.

Jan 1, 1998

Industrial and telecommunications organizations around the world are now turning to optical fibres to satisfy their growing needs for data, voice and video communications and to solve transmission problems in noisy and hazardous environments. Already, coaxial cables have been made obsolete for intermediate and long distance applications and fibres are making in-roads on other copper cable and microwave system techniques.The idea of optical fibres is not new, but techniques to manufacture the high quality cable and components required have only recently been developed. Nonetheless, the technology is now advanced, reliable and mature, and costs are plummeting with increased production and market competition.The mining industry has benefited greatly from developments in electronics and communications over the years. Optical fibres are to have a further significant impact and the time is now right for the industry to begin to exploit the many advantages of this new medium. Applications include data transmission, long distance telecommunications, measurement and control systems, surveillance, computer networks, etc.This paper briefly describes the characteristics of optical fibres, current status of the technology, applications and possibilities for future development.

Jan 1, 1984

The needs for improved technology for the mineral industry are widely recognised and a summary list is given. Ways in which technology has been introduced into the industry are discussed, as are the means by which the general process of technology transfer takes place. Some possible sources of improved and new technology are considered, together with the constraints to its introduction into the industry. Responses to recent external influences on the industry are discussed in relation to their effects on technology development.

Jan 1, 1986

By Nickelsen J, Theisen KG, Hansen PH

The use of stationary calciners in the processing of aluminium hydroxide has emphas- ized the importance of Bayer hydrate properties with respect to particle breakdown during calcination and subsequent treatment. Test results from calcination of several Bayer hydrates to sandy alumina in the FLS Gas Suspension Calciner (GSC) were obtained in a 250 kg/h pilot plant unit. Particle breakdown during calcination was influenced by content of solid sodium oxalate, trapped in the hydrate particles and operating gas velocities. Owing to the design and operational principles of the GSC it is possible to reduce particle breakdown to at least the same as what is found in long rotary kilns. Other major advantages reviewed are obtained through simplifications in plant design and operation, pointing to low specific power and heat consumption, and generally low production costs, thereby providing an attractive alternative to fluid-bed calciners.

Jan 1, 1981

By Cliff D, Harrison P. Hester C

During 1997 two different types of coal mine inertisation equipment were trialed in separate underground coal mines in Queensland.In April 1997 tests of the Polish developed GAG-3A inert gas generator were carried out at the Collinsville No 2 Coal Mine. These demonstrations indicated that the GAG-3A device was applicable in underground coal mines and that with respect to inertisation rate the device outperformed all other currently available techniques. The unit was assembled rapidly and operated safely during surface and underground trials and no mechanical problems were encountered with the device. The GAG-3A is not suitable for every fire scenario particularly if large volumes of fresh air are being drawn into the mine(where multiple units may be required), but with respect to the selection criteria developed by the Moura Implementation Process Task Group 5 criteria, the unit performed up to the specifications required.

Jan 1, 1998

By D Craw

A glasshouse experiment was set up to investigate arsenic uptake in rye corn grown in different arsenic rich substrates. Sods of material were taken from various locations and planted with rye corn seeds. The plants grew for 13 weeks after which time the above ground biomass was harvested. Analysis of the rye corn plants showed a narrow range of arsenic concentrations, which did not reflect the arsenic contents of the soil. Comparison of the results from this study with previous work showed the glasshouse rye corn to have lower arsenic concentrations in above ground biomass than rye corn grown in field conditions. The environmental conditions present on the tailings and water-rock interactions were considered the main factors involved with the difference in arsenic uptake between field studies and the glasshouse study. This suggests that bioavailability processes are influenced by a variety of factors and cannot necessarily be predicted by the use of soil factors or glasshouse trials alone as is often done when planning phytoremediation work and mine shut down.

Jan 1, 2007