Search Documents

By D J. Williams

Tailings management is typically constrained by many factors that are taken as given. These include the tailings production rate that must be accommodated, the desire to deliver the tailings cheaply and easily as a slurry using centrifugal pumps, and a tailings footprint limited by the desire to minimise capital costs leading to a rapid tailings rate of rise and a low settled density. Other constraints include wall raises being delayed due to limited capital, inadequate tailings water and rainfall run-off management, and the net present value (NPV) approach to capital expenditure that puts off expenditure at the expense of performance. All of these constraints result in the tailings occupying much more volume than is necessary, being difficult to rehabilitate, and not being capable of supporting a beneficial post-mining land use or function. Ultimately, such constrained tailings storage facilities will assume very large dimensions, but each will typically be developed as a series of smaller storages that are filled rapidly and added to progressively. The optimal stage to efficiently recover process water is in the process plant, but this is limited by the desire to use centrifugal pumps rather than the more costly positive displacement pumps, which also require greater management of tailings deposition. Process water can also be recovered from the tailings storage facility (TSF) decant. Tailings water that is not recovered from the plant or the decant will be lost to entrainment within the tailings, seepage to the foundation or through the wall, or evaporation. However, tailings water is not always suitable for reuse in the plant, particularly when it becomes contaminated by the processing, and it may simply be stored on the TSF. This will exacerbate the seepage of contaminated water to the environment, and will limit the densification of the tailings that would otherwise occur due to desiccation of the tailings on exposure. If a larger tailings footprint were developed early, cycling of tailings deposition in thin lifts between a number of cells could occur, maintaining the dormant cells dry to enhance desiccation and densification, and ultimate rehabilitation. The end result would be a much reduced stored volume of tailings, the potential for upstream raising, and ease of rehabilitation to a high level. The higher initial capital cost would be overtaken by reduced ongoing capital, operating and closure costs.CITATION:Williams, D J, ?2014. An alternative whole-of-life approach to tailings management, in Proceedings Life-of-Mine 2014 , pp 285–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

DuPont is a chemical and energy multi-national of approximately 90,000 employees. Often regarded as the world leader in injury reduction and process safety management, DuPont operate 140 manufacturing sites around the globe. Conoco is a wholly owed subsidiary of DuPont which is involved in oil, gas and coal exploration.   Throughout this paper I will discuss DuPont statistics, developing a safety culture and training process as well as discussing possible short comings in the New Zealand safety focus. I will conclude with my recommended improvements and issues for New Zealand companies to focus on.   It is very difficult to compare DuPont and New Zealand statistics through lack of compatibility in recording methods and my ability to interpret ACC's Injury Statistics. However through considering DuPont's statistics, and comparing them to your own companies or departments, you will agree they are indeed impressive. I hope that by discussing DuPont's safety philosophy, and possible shortfalls within New Zealand Legislation many of you will find ideas and inspiration which will help you to further reduce your own injury rates.

Jan 1, 1997

By Bigdy D. N

The paper describes a system for providing mine management with a continuous indication of the effectivness of longwall coalface powered supports in controlling roof-to-floor convergence. The system comprises on-face instrumentation monitoring convergence and support leg circuit pressures, a means of transmitting the output of that instrumentation to the surface for collection, and software which presents both a condensed analysis for rapid review of the current state, and extended analyses from which remedial action can be recommended if a problem is identified. The results of a field trial are presented showing that meaningful results can be obtained.

Jan 1, 1988

By S K. Ray

Open fire in a mine gallery causes large-scale damage to property and sometimes precious lives. Such fires produce two distinct effects, the throttle effect and the buoyancy effect. These effects disturb the ventilation system of the mine. To understand the complex dynamic phenomenon of open fire and its effect on ventilation systems, a mine fire model gallery has been designed and constructed at Central Mining Research Institute, Dhanbad. Two sets of experiments at air velocities of 1 and 1.5 m/s were conducted in the gallery using coal samples from the Dobrana seam of the Raniganj coalfields. After about an hour of development of fully-fledged fire, heavy backlash, with smoke and fumes, was observed. At the time of backlash occurring the gallery was divided into two zones. In the region of the gallery from the base up to 1.4 m the airflow was normal, in the remaining upper portion the airflow was the reverse. Air quantity reduced substantially, while pressure dropped across the fire zone, the products of combustion (POC) and temperature increased during the period of the throttle effect. It has been revealed from these studies that with an increase in airflow, pressure drops across the fire zone, POC, temperature and reduction in airflow increases. This paper addresses the important design features of the gallery, the instrumentation system, the experimental procedure and assesses the effect of open fires on mine ventilation systems.

Jan 1, 2005

I offer some comments which might complement the valuable recent paper by De Angelis et al (1987), on the newly discovered nickel-copper deposit at Radio Hill.The authors have accepted subdivisions and correlations by Hickman (1977, 1983) although they are disputed (Fitton, Horwitz and Sylvester, 1975; Horwitz, 1979; Horwitz and Guj, 1986).Also, in my opinion, more plausible correlations of the Sholl Belt with Whim Creek Belt have been shown, but not discussed, in Hudson and Horwitz (1986, Figure 1). Our suggested correlations and subdivisions have appeared in publications and reports which are not readily available, but it is gratifying to note that many of the observations and conclusions of De Angelis et al are consistent with our conclusions of the Whim Creek Belt.The units of the Sholl Belt (of Hickman, 1983), between the Sholl Fault (Shear Zone) and the overlying Mt Bruce Supergroup to the south, equate well with units of the Whim Creek Belt. A basalt, characterised by an abundance of vesicles and similar in many ways to the Wararnbi Basalt of Fitton, Horwitz and Sylvester (I975), is well developed at the base of the succession, particularly in the southern part of the area (Figure 1). It is overlain by acid tuffs (locally metamorphosed, such as at Whundoo Mine) and associated acid and mafic lavas, similar to those of the Mons Cupri area. The mafics in the succession are marked by the absence of the numerous cherty sedimentary intercalations, such as the Marble Bar Chert, which occur in the Warrawoona Group; and they also lack the intense chertification that is prevalent in all parts of the proven areas of Warrawoona Group rocks.The Whim Creek Group is overlain, locally unconformably (two to three km east of Mount Negri), by the Negri Volcanics which include here the Louden Volcanics (unit Abu of Hickman, 1977), (Horwitz, 1979). The negri volcanics are an alternating sequence of variolitic and quench textured lavas not dissimilar to the highest units of the Sholl Belt (Figure 1). They range from high-Mg basalt to tholeitic andesites (Glikson et al, 1986, pp 79 and 84). The whole succession of the Sholl Belt is estimated to be of the order of four km in thickness, more consistent with the two km thick (Horwitz, 1979, Figure 1) Whim Creek area sequence than with the much thicker Warrawoona Group sequences. The Whim Creek Group (including the Negri Volcanics) is considered to be a widespread grouping (Fitton, Horwitz and Sylvester, 1976; Horwitz, 1979; Horwitz and Guj, 1986) which is prevalent in the northern part of the Pilbara Craton. It is considered by these authors to include the Mallina Formation turbidites of the trough area of Ryan (1965). One component, the Mons Cupri Volcanic, is about 2.95 Ga (Richards and Blockley, 1984). Between the Sholl Fault and Egina, the Whim Creek Group is intruded by large ultrarnafic to granophyric ills of the Millindinna Complex (Fitton, Horwitz and Sylvester, 1975), dated at 2.860 ± 002 Ga by Gulson and Korsh (1983) near the Sherlock River (south side of Caines Well Granite area). The Millindinna Complex has been equated to the same magmatic episode as the layered complexes of the Sholl Belt by Fitton, Horwitz and Sylvester (1975, p 20).

Jan 1, 1988

Sixty years after its inception, after an alternation of periods of admiration and rejection by the industry, Sampling Theory can now be seen as going through its golden age. A brief history of its successive transformations and progresses achieved by its author, Pierre Gy, and his followers, reveals the theoretical as well as practical difficulties that had to be vanquished to reach this point. Its current level of acceptance and corresponding trends are discussed and illustrated, with an insight on its increasing real role in the industry and future prospects for its further development.

Jan 1, 2008

By H Stedman

Integrating exploration and operational blastholes into one database significantly enhances geological modelling. Benefits include: improved coal predictions, stronger interpretation of structurally complex areas, detailed mapping of heat affected coal aureoles and additional roof accuracy for blast designs that deliver better coal protection.CITATION:Stedman, H, 2014. Integrating blastholes into exploration data to improve coal recovery and modelling, in Proceedings Ninth International Mining Geology Conference 2014 , pp 237–242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

The purpose of this paper is to explain the basic structure of how minerals are marketed, whilst highlighting the essential factors that mine management needs to be confident are incorporated into a mineÆs marketing strategy. The traditional mine management approach to marketing has been to defer its scrutiny to the marketing manager and take a largely passive role. It is this paperÆs assertion that mine management needs to become more proactive and provide greater strategic input into the marketing process. Irrespective of what mineral your mine produces, the key marketing principles remain constant and need to be understood and managed to extract the full benefit on behalf of the mining asset. From a mine management perspective, success is ultimately linked to understanding these marketing principles and ensuring that they are effectively addressed by your mineÆs marketing strategy. This paper will unashamedly attempt to simplify marketing by explaining how the basic fundamentals of supply and demand set market direction, the importance of a comprehensive marketing strategy, the importance of customer relationships and how contracts and prices are typically negotiated. This paper will use examples from the metallurgical coal (met coal) industry to highlight these points. The paper will also provide a template for developing the critical mine interaction that needs to exist between the marketing department and management to develop a æwhole of mineÆ approach to marketing. It is this core group that will be strategically responsible for delivering the commitments your mine has made to your customers. For mine management not to be actively involved in this process puts at æriskÆ the hard won production and cost efficiencies achieved at your mine and ignores the opportunity to maximise your current and future revenue streams. And whilst this paper recognises that is arguably unreasonable for mine management to become æmarketing expertsÆ, it also argues that it is unreasonable for a mine management to divorce themselves from the process.

Jan 1, 2006

The difficulty in screening of ores when the moisture contents reach certain critical levels has resulted in mining circuits using wet processes for screening. While this has been acceptable in past years it is no longer acceptable in certain countries and where the mining company is looking to reduce its impact on the surrounding environment.   Various mining companies have been looking at ways to remove the need of using water, with all its inherent drawbacks and to be able to produce its desired products in a dry process.   This would have the benefits of less environmental impact and cost, (due to not requiring wet processing equipment), less power consumption (reduced equipment needed), no corrosion issues, no contaminated waste waters and reduced maintenance activities.   Until recently this has proven elusive or with technical restrictions with current available acceptable technologies for high capacity plants.   One major mining company began seriously exploring ways to overcome this dilemma so that they did not replicate their current ways of operating for their new expansion plans.   They partnered with Metso Minerals to undertake extensive groundbreaking laboratory test work and provide potential solutions as to how to solve this. The laboratory test work proved interesting enough to design, manufacture and test on the actual mining site a prototype screening machine in the circuit.   This break through in screening technology reduces the environmental impact on the area in which the mine is located by: eliminating the storage and use of water, reduction in energy consumption due to having no pumps in the plant, reduction in plant costs and the upstream affects on the environment process used to manufacture and ship the materials the plant structure is built from, and no large tailings dams to take up land space and affect the environment through groundwater/ water table contamination and the negative effects on animals and ecosystems Laboratory test were conducted and a full size machine was installed at the plant site along side conventional machines. The screen size (2.4 m wide x 6.1 long double deck) was determined by the size of screens currently in operation at the mine. The parameters that were explored were: types of screen surface (polyurethane, woven wire etc), types of screen motion (linear, circular or elliptical), angle of motion ( 40,45,55,60 degrees etc), and throw (amplitude), speed and 'g' force.

Jun 1, 2010

By D E. Tennant

In the fields of geotechnical engineering and slope management, various software packages are used to assess the behaviour or propensity for a slope to fail. Traditional kinematic analysis calculates the probability of failure of design sectors with respect to dominant structural set orientations. A novel methodology is provided here to view potential hazardous slope behaviour in 3D, allowing engineers to make informed decisions regarding various pit slope geometries. Apparent dips are calculated for every point in space with respect to every slope orientation of the entire pit surface/design, specifically in reference to bench and inter-ramp planar failure mechanisms. Implementing a proactive approach to slope design will not only lead to early mitigation of risk but can also add direct value by enhancing or improving upon slope angles for earlier access to ore. From a safety perspective, identification of unfavourably oriented slope geometries can be dealt with before failure occurs. This methodology relies on a strong understanding of the existing rock mass anisotropy, particularly behind the face, thereby removing some of the uncertainty surrounding pit design as well as presenting engineers with an additional means to manage risk.

Nov 29, 2022

The link between exploration success and new ideas from research and development (R&D), although often assumed, is rarely well explained or well illustrated. One issue is understanding the role of innovative ideas in the exploration process, and another is determining the relative contributing factors to an exploration success. A useful measure of gold exploration success over an extended time period and geographic area is discovery rate (θ): Discovery rate θ = gold discovered/exploration expenditure (usefully expressed as tonnes of gold per $1 million). The total gold discovered is strongly leveraged to discovery rate, as any increase in θ typically has a positive effect on exploration expenditure. Hence, improving the discovery rate is a key driver for a sustainable mineral industry, especially for gold. There are very few ways to influence θ beyond innovative R&D ideas and breakthroughs, and well-motivated and trained staff. The Australian gold industry has experienced exceptional exploration success with 9956 tonnes of gold discovered from 1979 to 2003, inclusive. This equates to: Discovery rate θ = 0.9 t/A$1 M Two-thirds of this gold has been found in the Yilgarn craton of Western Australia (6265 tonnes Au). Without this exploration success, there would have been no platform on which to build the current gold industry and to take advantage of elevated gold prices and advances in mining and processing. Several causes of the Western Australian gold success have been proposed, and more than one may be correct. Gold price, and mining and processing advances have all had influence; but exploration success and discovery of gold were essential to add to the miniscule resource base of 1979. A comparison of the exploration methods used to search for gold in the Yilgarn craton in 1979, and 1990, highlights a small number of breakthrough ideas introduced to the industry during the 1980s, and in most cases emanating directly from local R&D. By the 1990s, these ideas were being used in most gold exploration programs in the Yilgarn craton, and are still used today. These six breakthroughs are: epigenetic timing of gold deposit formation (ie after formation of rock sequence), chemical and mechanical role of host rocks, relevance of carbonate alteration haloes, gold dispersion in the regolith, optimal sampling media, and appreciation of landforms in exploration program design. Interestingly, gold exploration science in Western Australia entered the 1980s period without rigid paradigms in place regarding gold deposit formation; there was a balance between descriptive and genetic models, there was scope to research gold deposits from microscopic to global scales and there were highly effective industry research uptake processes in place: it is suggested here that these favourable conditions contributed to the exploration success and industry growth.

Jan 1, 2007

By F Clark, B Catto

The Mako domain comprises the Mako lodes at Sunrise Dam Gold Mine, Western Australia. This domain was initially bulk or æbucketÆ domained for the open pit resource in 2000, due to complexity in defining the lodes as a result of low drill density. Negative ore tonnage and positive grade and ounce reconciliations were experienced during mining of the domain in the mega-pit, though only small volumes of the domain were mined. Significant amounts of exploration and underground grade control drilling has been completed since the initial bulk domain interpretation and greater geological understanding of the mineralisation controls and geology of the lodes now exists. Mako provides approximately 50 per cent of the ore tonnes and ounces for the North Wall Cut-back, the latest open pit phase of mining at Sunrise Dam. The importance of Mako to mill supply and life-of-mine planning, as well as past reconciliation performance necessitated a reinterpretation of the domain to increase confidence for mining. Historic exploration drilling, underground grade control drilling and detailed pit-wall mapping were used to build mineralised subdomains within the confines of the original domain. These reflect more closely the spatial extents and geological controls on the mineralisation. A new resource model using the multiple indicator kriging (MIK) technique was generated using the new domains. It resulted in a decrease in tonnes and ounces but increase in grade for the sum total of the new domains compared to the old æbucketÆ domain. This is attributed to the increased selectivity and structural constraints imposed by the new domains. A retrospective comparison of the Mako grade control from the mega-pit versus the new resource model was conducted, which æreconciledÆ 103 per cent tonnes, 106 per cent grade and 110 per cent ounces. This has provided confidence that the new model is a better estimate of the lodes. Qualitatively, the new model is a better representation of the geology and extent of the mineralised structures with significant areas of change identifiable. Grade-tonnage plots comparing the 2006 and 2008 models show that most tonnes have been shed from the low-grade û subeconomic grade cut-offs. This is mostly attributable to the volume reduction of æoreÆ in the 2008 model compared to the 2006 model, where the true mineralised zones are captured by the new domains. The reinterpretation and remodelling of Mako is an example of an evolved domain model and shows that mineralised zones need to be differentiated adhering to the geology and geological controls on mineralisation, which are understood largely due to increased drilling density coupled with mapping.

Jan 1, 2009

By Hagarty KA

At the northern margin of New Guinea there is a fundamental problem related to the relative timing of arc- continent collision(s) represented in the Papuan Fold-Belt (PFB) and backarc spreading in the Caroline basins. New fission track dates from basement and sediments within major anticlines of the PFB indicate that uplift occurred at 4.0 ¦ 0.5 Ma. The timing is consistent with the fold and thrust shortening (more than 100 km) of the PFB which occurred in the Late Miocene/Early Pliocene as evidenced by the deformed Miocene carbonates and Pliocene molasse deposits. However, in northern Papua New Guinea, earlier work has suggested that ophiolite emplacement and associated metamorphism occurred in the late Oligocene/early Miocene.The evidence suggests that the late Miocene/early Pliocene deformation was of considerably greater magnitude than the earlier obduction event. The Caroline Plate lying north of New Guinea has been interpreted as a backarc basin which commenced spreading in the Eocene and ceased spreading in the Late Oligocene (about 28 Ma). The remnant arc presently docked to New Guinea was active in the Eocene and Oligocene and is believed to be the arc related to the formation of the Caroline Plate. The cessation of spreading of the Caroline Plate has previously been interpreted to be due to arc continent collision during the Late Oligocene/Early Miocene, but such a collision is now known not to have occurred. In the Cretaceous and Palaeocene subduction was to the south beneath New Guinea, but "flipped" in the Eocene to give a north-dipping subduction zone far to the north of New Guinea, driving Caroline Plate backarc extension. This backarc basin reached a limiting size at about 28 Ma resulting in the end of subduction. With the continued northward movement of Australia, Mesozoic oceanic crust was obducted southward onto the New Guinea margin in the Late Oligocene/Early Miocene. In the Miocene south-dipping subduction beneath New Guinea commenced until the now extinct Caroline Plate arc collided with New Guinea in the Early Pliocene, causing extensive regional compression and sinistral strike-slip faulting. This new tectonic framework suggests that backarc basins reach a limiting ridge-trench distance of 1000-1500 knm, beyond which "subduction-pull" cannot drive further spreading so subduction and spreading are terminated.

Jan 1, 1987

By Dagbert M, Belisle J. M

Several packages for the estimation of porphyry type deposits exist and produce acceptable results. Recently, however, the need for really trying to obtain maximum information from drill holes has prompted the generation of geostatistical solutions to the problem of reserve calculation. It will be shown that an understanding of a few key points is necessary in order for these solutions (variogram analysis and kriging) to he really ptimal. The most important new fact to be ecognized in open pit ore reserve estimation is that block models do not give an accurate rediction of ore tonnage when a cut-off is pplied but often yield an overestimation of p to 25%. When checked against extensive roduction records, geostatistical methods provide a practical solution to this problem. t now seems that the model used here gives he best possible results. Inasmuch as all arge deposits present very similar geostatis- ical characteristics only a few days of work re necessary to produce a complete inventory f these. The techniques used will be demon- trated using examples from five deposits and pecial emphasis will be given to the accurate rediction of tonnages of ore and waste using he new "transfer function" technique of G.

Jan 1, 1977

By Robertson K. S, Hunter T. C

AEG-Elotherm's electromagnetic dosing channel, or Eldomet, is a recent invention enabling the transport and metering of molten metals. The development of a reliable refract- ory lining, and the use of suitable construct- ion and operating techniques has led to the successful application of the Eldomet for casting copper anodes at Copper Refineries Pty. Ltd.

Jan 1, 1974

The Kyaukpahto gold deposit is located at latitude 23¦ 47Æ 55" N and longitude 95¦ 56Æ 35" E in the Kawlin-Wuntho district, Sagaing Division, Myanmar. Gold mineralisation is hosted in sandstone of the Male Formation (Eocene) and occurs as stockworks and disseminations. The high-grade gold mineralisation is locally concentrated in a breccia zone. The gold deposit is closely associated with a NNE-SSW trending fracture system that forms tensional open fractures. These tensional zones are thought to be directly related to the Sagiang transfer fault system that experienced several hundred kilometres of northward dextral movement during the post-Upper Miocene. Major sulfide minerals are pyrite and arsenopyrite with minor galena, chalcopyrite and sphalerite. Gold mineralisation is associated with intense silicification, sericitisation and argillic alteration. Primary Type I fluid inclusions in the quartz from the mineralised zone are 5 to 15 ¦m across and yield homogenisation temperatures of 239¦ - 310¦C and salinities of 1.2 - 10.9 wt per cent NaCl equivalent. Laser Raman spectroscopic analysis indicates the presence of CO2 and CH4 in Type II fluid inclusions. Sulfur isotope analysis of disseminated pyrite in the ore zone by the laser ablation method indicates d34S values from -5.48ë to +5.53ë. The geology, alteration, ore mineralogy, fluid inclusion microthermometry and sulfur isotope data of the Kyaukpahto deposit are consistent with an epithermal ore deposit model for the deposit. However, the presence of CO2-liquid bearing fluids and the detectable CH4 in the gaseous phase of the fluid inclusions conflict with a typical epithermal origin for the Kyaukpahto deposit. The host siltstone and mudstone sequence, trace element geochemistry, and the disseminated nature of sulfide and gold mineralisation are also common characteristics of a sedimentary rock-hosted gold deposit, and these features may indicate a Carlin-like affinity. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By J Kleynhans, D Vermeulen, V Cogho

A number of rehabilitated open cast coalmines in SA are already decanting. The paper focuses on the situation at one of these mines where the following information exist: monthly decant rates and rainfall; sulfate concentrations of the decanting water; water level measurements inside the mine prior to decanting; ABA analyses; information about the rehabilitation (drainage slope, vegetation, soil used). A 2D-model was constructed for the mine and calibrated against six years of flow data. About 85 per cent of the decant outflow rate comes from direct recharge on top of the rehabilitated mine while the other 15 per cent is derived from lateral groundwater inflows. The estimated recharge value was 17 per cent of the rainfall. Measured sulfate values showed that the sulfate generation rate for the mine was in the order of 7 kg/ha/d. Conclusions from the study are:most of the water decanting from rehabilitated open cast coal mines is derived from recharge via rainfall; given a specific sulfate generation rate, then: the lower the recharge the less the decant rate but the higher the sulfate concentration of the decanting water and vice versa; future prediction of the decant rate must be stochastic according to expected percentile monthly rainfall values; and as a first assessment of the predicted sulfate concentration of decant water from rehabilitated open case mines, the 7 kg/ha/d sulfate generation rate can be used.

Jan 1, 2003

Traditionally mill operators have been employed with varying educational backgrounds with little if any formal training in aspects of mineral processing. Pasminco Mining-Rosebery, in line with other organisations, saw the need for a prerequisite entry level for operators to enter the industry. After initial discussions between various West Coast Mines personnel, union and government representatives, an industry working group was formed in 1989 with the aim of developing a traineeship suitable for the mineral processing industry. Training and technical representatives from four of the West Coast Mines and TAFE were commissioned with the curriculum development. The resultant course, which is recognised under the Australian Traineeship system, involved an integrated on and off-the-job training program, including 13 weeks of formal off-the-job instruction.

Jan 1, 1991

Acupan is considered to be an intrusive centre as several igneous phases have been emplaced in the vicinity of the mine over the past 8 Ma. They include the Lucbuban gabbro, Virac granodiorite, Ampucao dacite porphyry (ADP), Hartwell plug, Itogon plug and the multi-phase Balatoc diatreme. These intrusives have high-K calc-alkaline affinities and are grouped together as the Virac Complex.Porphyry-style mineralisation formed during the final crystallization of the ADP in the late Pliocene, with the deposition of two vein stages from high-temperature hypersaline magmatic-hydrothermal fluids. K-silicate alteration halos surround the first stage of veinlets (stage I); they are surrounded in turn by a propylitic assemblage. White sericite and/or intense propylitic halos envelop the second stage of veinlets (stage II) and grade into a weak nrnnvlitir accPmht o

Jan 1, 1990

The geochemistry of waste rock from mining operations is critical to the development of acidity-related environmental problems during mining operations, and following mine closure. Failure to recognise the potential for waste rock to produce acidic oxidation products may cause mobilisation of heavy metals into ground and surface waters, and create heavy metal levels in soils which are toxic to plants, causing the failure of revegetation programs. Although more usually associated with wet tropical environments, the potential exists for these problems to occur even in and regions such as the Eastern Goldfields region of Western Australia unless appropriate pre-planning is undertaken.Acidity-related mine waste problems can be extremely expensive to rectify, but can be avoided by waste rock characterisation, and pre-planning of waste rock deposition based on this information. Integration of knowledge of waste rock geochemistry with geotechnical engineering, and application to likely problems, is essential for the successful planning and implementation of cost-effective strategies to avoid problems occurring. Pre-planning to avoid problems is likely to be significantly less expensive in most cases than remedial actions to rectify problems after they have occurred, and in fact may involve no additional cost if it requires only rescheduling or redesign of existing or planned Activities.

Jan 1, 1993