Search Documents

By D E. Ralph, D-J Kim, G-J Ahn, Y-H Rhee

The amount of discarded dry batteries are presently found to be increasing globally and waste cathode active materials of the lithium ion battery industry are among them. Hydrometallurgical operations are being applied to recover the valuable metals from these waste batteries. To find an economic and environmentally friendly process, the bioleaching process was applied in the present investigation for recovery of valuable metals. Its principle is the microbial production of sulfuric acid and simultaneous leaching of metals. Bioleaching of spent lithium ion secondary batteries, containing LiCoO2, has been studied in this investigation. A new method for recovery of cobalt, potentially the basis of an economic and environmentally friendly process was examined. The present study has been carried out using chemolithotrophic and acidophilic bacteria Acidithiobacillus ferrooxidans, which utilises elemental sulfur and ferrous ion as the energy source to dissolve metals from spent batteries. Bio-dissolution of cobalt was found to be faster than lithium. The effect of initial Fe(II) concentration, initial pH and solid/liquid (w/v) ratio were studied in detail. Higher Fe(II) concentration showed a decrease in dissolution due to co-precipitation of Fe(III) with the metals in the residues. Similarly, at higher initial pH values and higher solid/liquid ratio (w/v) metal dissolution was found to be inhibited. The optimised conditions for bio-dissolution were solid/liquid (w/v) ratio û 10 g/L, initial Fe(II) concentration û 3 g/L, elemental sulfur û one per cent (w/v) and initial pH û 2.5. In the optimised conditions, cobalt dissolution was observed to be about 60 per cent, whereas that of lithium was ten per cent after 20 days. A first order kinetic model was derived to study the rate of dissolution of both the metals.

Jan 1, 2006

By A Turns

In a survey conducted by symplexi with underground miners in Australia; 78 per cent of participants believed that ‘safety’ is all about people. If ‘safety’ is about people, then is the mining industry focusing on the wrong thing? It would be fair to say that the mining industry is heavily systems focused. Companies develop a safety management system and use this to show regulators that they comply with legislation – however, that is only half of the picture.

May 5, 2022

By T Muri

The drying operation of materials from particulate solids, through slurries and suspensions, to continuous sheets represents an important part of several processes in the chemical and mineral industries. The increasing demand of high productivity at low cost and minimal environmental impact makes it complex to evaluate and choose the best available drying technology for each industrial application. The drying technologies are mainly characterised on the basis of how the wet product is related to the drying medium, namely: direct and indirect drying. In the direct drying method (convection drying), the product is brought into direct contact with the drying medium, which may be hot gas or air. Large quantities of gas are necessary for transfer of the required energy. A special case of the direct dryer is the fluid bed dryer, in which the product floats on a cushion of air or gas. The process air is supplied to the bed through a perforated distributor plate and flows through the bed of solids at a velocity sufficient to support the weight of particles. Very high heat and mass transfer values are obtained as a result of the intimate contact with the solids and the relative velocities between individual particles and the fluidising gas. In the indirect drying method (conduction or contact drying), the wet product is separated from the drying medium. The drying unit can consist of a rotor forming the indirect contact heating surface mounted in a stationary or rotating shell. The indirect method uses saturated or superheated steam resulting in low energy consumption and minimal environmental impact. In this paper, a review is given of the technologies available on the market based on different drying methods. The advantages and the disadvantages are summarised with respect to issues such as investment and operating cost, maintenance, product capacity, product handling and environmental impact.

Jan 1, 2006

By Reid A. F

Since early 1971 Western Titanium N.L. has been operating an ilmenite upgrading plant on a commercial basis at Capel, Western Australia. In their process ilmenite is pre- oxidized, then reduced in a rotary kiln to a mixture of metallic iron and titanium oxides. The iron is leached out by accelerated rusting in aerated water, leaving a product with titanium content, expressed as Ti02, of about 92%. Samples from different stages of the up- grading process, representing operations over the last two years, have been studied in detail by X-ray diffraction methods, and the sequences of phases and reactions occurring have been determined. Quantitative X-ray studies showed the ilmenite feed materials to consist of a mixture of ilmenite and pseudo- rutile. Pre-oxidation of the ilmenite at =1000¦C leads to the formation of rutile plus a Fe2TiO5-FeTi205-Mn2TiO5 solid solution. The final reduction product consisted of a mixture of metallic iron, reduced rutile and a FeTi05-MnTi205-Ti305 solid solution. The relative amounts of these reduction products were very sensitive to the initial concentra- tions of the minor constituents manganese and magnesium. The effects of variation of ilmenite feed rate, reducing atmosphere,- reduction temperature and controlled addition of magnesium were also studied.

Jan 1, 1973

By B C. Povey

HPGR technology has been used at a number of magnetite mines in the world and have significant energy advantages over SAG and AG technologies. The early design at Los Colorados in Chile has been in operation for more than 12 years - and operates very successfully though only reduces the feed size to -5mmThe Whyalla project magnet design pushed the concept to produce a preconcentrate of 80%-350micron - a significant reduction on previous plants though with some wear problems in the early years. The Karara design backpedalled slightly and will only crush to 80%-1.8mm.However, the design issues of using a HPGR to further reduce the feed size continue to be explored. The aim is to reduce the process risks associated with wear and also to reduce the complexity of the downstream process - with consequent benefits in terms of capital and operating costs.The designs are being developed for a couple of projects - one planned to produce 20Mtpa of concentrate with the potential to not only remove SAG and AG milling but also ball milling. The concept is to use multiple passing through the HPGR since, on the data available, the efficiency of the HPGR to reduce size does not significantly diminish as the feed size is reduce. This can be have benefits in both capital and operating cost.CITATION:Povey, B C, 2013. Pushing the use of high pressure grinding rolls in magnetite circuits, in Proceedings MetPlant 2013 , pp 176-189 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

Carbonation of reinforced concrete is a potential durability issue for vehicular tunnels. This is particularly the case where elevated carbon dioxide concentrations exist and when the design life is 100 years or more. The process of carbonation can result in loss of passive protection to embedded steel reinforcement and initiation of corrosion. Therefore, tunnel design needs to consider the potential for carbonation on internal surfaces and how design life can be achieved in severe environments. This paper examines methods for predicting carbonation and how deterioration can be mitigated through appropriate concrete mix design and construction practices.

Jan 1, 2008

It should be noted that with the passage of time all aspects of the mineral extraction process are becoming more sophisticated and complex. In order to deal with this, the education system should be geared to this continual technological advance.A new scheme is designed to attract high quality school leaven to take up courses serving the mineral industry. After graduation these students will play an important role in the areas of research and development which is essential for the growth of the Australian mining industry.

Jan 1, 1991

By Burchell S, McGregor K

The process of design, measurement and review is essential if blasting is to continuously improve to meet the increasing productivity goals of most mining operations. To achieve continual improvements, many operators are turning to contractors to provide the necessary technology. Under this arrangement, the contractor becomes the supplier of a service rather than products and assumes some of the risks associated with blasting by guaranteeing the end result. If contractors are to obtain significant productivity improvements they must continuously improve every aspect of their business.

Jan 1, 1994

The theme i wish to develop in this talk is how we might make use of the scientific and technological knowledge we now have ofextraction metallurgy to meet the present-day needs of the production industry.Before doing so, I would like to say a few words in tribute to Dr. G.K. Williams since he was a past master at precisely what I wish to talk about. I knew G.K., as everybody called him, during the time he spent at Avonmouth in the late 40's and in the 50's. Later, when he was ostensibly retired, I had the pleasure several times of lunching with him when I was visiting Melbourne.When G.K. was at Avonmouth, the Imperial Smelting Process was in that capricious adolescent stage in between the pilot plant and the full-scale commercial unit. G.K. was a great collector of process plant data which hung in cascades from the walls of his office and-from his hand-operated desk calculator. What G.K. understood very well were the basic metallurgical and engineering principles of what was going on in the sinter machine, the shaft furnace and all their ancillaries.

Jan 1, 1985

By Szpindler G

The results of pot-furnace tests with 35 bituminous coals from 20 seams in New South Wales and Queensland were used to establish the relationship between coal properties, as determined by standard laboratory tests, and the combustion process. The rate of combustion is influenced chiefly by the expansion of the fuel bed, but this cannot be accurately predicted from the crucible swelling number of the coal.The effects of various other factors, such as calorific value and ash yield, were investigated and statistical analysis of the results shows that the coals could be classified satisfactorily according to two experimentally derived parameters, namely heat-release rate at an air flow rate of 260 lb/sq.ft/hr and air flow rate giving stoichiometric combustion. The grouping obtained is shown to be related to ash yield and swelling number.INTRODUCTIQNThe rate of heat release from the fuel bed of a travelling grate stoker and the efficiency with which the heat is used depend upon the design and method of operation of the furnace as well as upon the properties of the fuel. It is difficult to draw general conclusions concerning the influence of fuel properties from tests on a single stoker installation. In the pot-furnace test, on the other hand, a part of the same combustion process as occurs on a travelling grate is carried out in isolation, uninfluenced by furnace design variables, and consequently the effects of coal properties and of the method of pretreatment can readily be demonstrated.While the combustion pot provides a rapid method of assessing the combustion characteristics of a fuel during the ignition and burn-out stages under standard conditions, and of predicting changes in performance with changes in fuel or in air flow rate, it is unable to simulate certain features of furnace design and operation. Data from combustion pot...

Jan 1, 1962

A practical approach has been developed for the design of both grates and pulp lifters. It is based on: an appreciation of the process interaction between grates and pulp lifters, an interpretation of mill charge structure as it relates to discharge through grates, and an analysis of pulp and solids flow in pulp lifter channels. This approach can be used to improve the overall discharge effectiveness of AG and SAG mills.

Jan 1, 2000

By Aziz NI, Bridgwood EW, Singh RN

One of the major impacts of using modern mechanised systems of mining is the production of large amounts of extraneous dirt intermixed with the Run of Mine output. The paper out- lines a proposed system of utilizing liquid tailings from coal mines to replace imported cementitious materials used in ground control and various other safety measures. A geotech- nical and cost assessment of the proposed system are also included. The paper concludes that it is possible to utilize processed tailings to cost effectively replace imported packing material for ground control.

Jan 1, 1986

By T Raynlyn, A Edenton, M Adam, R J. Holmes, J R. Manuel, N Ware, R Smyth

Due to ongoing demand and increasing depletion of high-grade iron ore resources from large deposits, Australian iron ore producers are developing smaller size deposits to maintain current export levels. The iron grade, mineralogy, chemical and physical characteristics of iron ore fines being mined from different deposits vary considerably. It is therefore imperative to develop long-term strategies to maintain the quality and consistency of iron ore fines while moving to a larger diversity of smaller deposits. Blending is a common practice in sinter plants as it is almost impossible to produce a high performance sinter mixture displaying the required characteristics from one single ore. Blending is also one of the most effective options being used by iron ore producers to ensure the long-term stability of their products while increasing production. When designing a blend, the blend components are selected to support each other to achieve the required overall balanced metallurgical performance of the final product at a relatively low cost. To do so, a fundamental understanding of the key characteristics of iron ore fines and their potential impacts on the iron ore sintering process and sinter quality are required. In this paper, the sintering process and sinter structure have been analysed and the key factors affecting the sintering performance of iron ore fines, including productivity and quality, identified. Under fixed sintering conditions, the granulation efficiency, nuclei stability and the volume and properties of the primary sinter melt are believed to have important impacts on both sintering productivity and sinter quality. Discussion is then focused on the effects of ore chemical, physical and mineralogical characteristics on the key factors identified and in turn the consequences for sintering productivity and sinter quality.

Jan 1, 2009

The process and control technologies incorporated into the coal preparation plant at Newlands were to be used for the first time in Australia. The commissioning organisation and procedures were set up on the basis that commissioning personnel, while being competent, would be unfamiliar with the equipment. In addition the commissioning process would have to be completed quickly. The organisation coped with all of these problems and more.

Jan 1, 1986

By H Jha, M C. Thomas, P Gupta, S K. Sit

The modern jig with a state-of-the-art control system is much more effective than its older version. This improved control system is used to modulate the amplitude and the frequency of the jig cycle. These two prime parameters are optimised with respect to feed characteristics for best jigging performance. Based on this understanding any jigging plant can be optimised. In addition to these established facts present study shows process efficiency improves further through optimisation of the feed quality.

Jan 1, 2007

The Golden Cross mine is a Joint Venture between Coeur Gold New Zealand Limited, as Manager, and Viking Mining Limited The mine is targeting Zero Lost Time Accidents as a goal. The Golden Cross operation produces gold and silver from both underground and open pit. The mine is based on an epithermal gold-silver deposit. Treatment of ore is on a campaign basis for each ore type (ie underground or open pit). Milling is conventional SAG Mill and Ball Mill grinding circuit followed by carbon in pulp recovery of gold and silver. All tailing materials are treated through the Cyanisorb process to reduce cyanide levels prior to being discharged into the tailings dam.

Jan 1, 1995

By D Kentwell

This extended abstract and associated presentation provide a series of real examples of the complex interactions between the numerous input parameters, both geological and mathematical, that are required for resource estimation. Many of these parameters can contain a large degree of uncertainty at the initial resource stage. The resource tonnages and grades at economic cut offs of some types of deposits are relatively robust to these initial uncertainties while others exhibit significant sensitivity. In some cases, changes in parameters can result in counter-intuitive outcomes. Grades and confidence levels are inseparable; as the parameters change the confidence changes and so does the grade estimate. The extended abstract and associated presentation also discuss the question of whether or not a single solution is still an acceptable outcome for an estimate or if even a set of simulations based on a single fixed set of parameters is acceptable.CITATION: Kentwell, D, 2018. Sensitive dependence on initial conditions in resource estimation, in Proceedings Complex Orebodies Conference 2018, pp 28–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Langberg D, Gray N. B

The flocculation of hydrophobic magnetite with gold was examined as a possible means of recovering fine (95 per cent were possible for 1.5 - 3.0 ¦m and 5.5 - 7.5 pm gold sizes. The effect of process variables on the flocculation process was explained by variations in the adhesive force between the gold and magnetite.

Jan 1, 1991

By N Bianco, D Drinkwater

The professional skills shortage is intensifying, and commentators are predicting a shortfall in supply of qualified professionals for the mining industry, ranging from thousands to tens-of-thousands by 2020 (Tuckwell, 2011; Scoble, 2011; Laurence and Hebblewhite, 2011). Human resources are already stretched, and university graduates arriving in the workplace are often moved rapidly into management positions where there is limited scope to develop their engineering proficiency. This process may well be developing excellent young managers, but our industry is producing fewer excellent young engineers (Munro and Tilyard, 2009). Many believe that it is engineering excellence that is likely to be the key to our industryÆs success in the decade to come. An innovative in-house graduate development program has been created by specialists at the JK Centre in partnership with two mining companies. This program, known as MetSkill«, has been running throughout 2012. Groups of graduates have had to identify a process plant optimisation opportunity and embark on a structured program of data collection and analysis, facilitated by a æteaching teamÆ of researchers and consultants from the Julius Kruttschnitt Mineral Research Centre (JKMRC) and JKTech. This group project culminates in a report-back session to senior company officials. Along the way, a series of short workshops and other activities provide opportunities to work on specialist skills, and support is also offered by senior technical specialists from the companies involved.This paper outlines key features of the MetSkill« program, along with a report-card on progress in 2012 and plans for further program development in 2013.CITATION:Drinkwater, D and Bianco, N, 2012. Developing minerals industry leaders by encouraging metallurgical excellence, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 287-290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By S J. Henderson

Over much of Australia, rainfall is highly seasonal and storm-driven. Consequently, operational mines often need extensive earthworks – drains, dams and levees – for protection during the occasional large floods and for water storage against the dry times; however, it has not been appreciated that many of these earthworks will need to function after mining has finished, sometimes, beyond a normal design life for engineered structures.While a mine is operating, standards for design and maintenance are dictated by regulation and risk assessment. For dams and levees – regulated structures – the standards imposed mainly relate to life-of-mine. The levels of risk and maintenance accepted by the mine operator may not be acceptable to another landholder in perpetuity. However, the Environmental Authority cannot be surrendered unless the landholder has accepted responsibility for any unrehabilitated regulated structures (Department of Environment and Heritage Protection (DEHP), 2016).In order for a future landholder to be willing to take responsibility for a dam or levee, the structure should be of value to the business of the property. In addition, its management needs must be consistent with that business; for example, it should be maintainable using skills, equipment and materials normally available to the business.CITATION:Henderson, S J, 2016. Earthworks or landforms? Designing for lease surrender, in Proceedings Life-of-Mine 2016 Conference , pp 151–153 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016