Search Documents

By L Smith, R Beckie

An intermediate scale (8 m + 8 m + 5 m high) constructed waste rock pile experiment was built upon a contiguous grid of 16 gravity drainage lysimeters to investigate the flow of water in unsaturated waste rock. Average net infiltration to the uncovered waste rock pile is 55 per cent of precipitation. Large rainfall events have net infiltration of 55 per cent to 85 per cent. Net infiltration estimates range from 23 to 120 per cent of precipitation between lysimeters. Small-scale lysimeters of less than 4 m2 area are shown to be poor predictors of net infiltration for uncovered waste rock. The appropriate size for lysimeters increases with increasing flow rate. The residence time distribution has an estimated median value of 3.0 to 3.9 years under average infiltration conditions. Water flows within the fine grained matrix, within larger pores (macropores), and in matrix free areas of the pile. In situ tracer concentrations vary between pore sizes, and between spatially distinct areas of the pile, indicating water geochemistry may also be variable. Water samples collected from in situ soil water samplers are dominated by the most mobile water fractions. In situ measurements of water content and matric suction are compared to the measured outflow. The data indicate the focusing of flow in spatially distinct areas can make in situ instrumentation a poor (non-conservative) predictor of volumetric water flow.

Jan 1, 2003

Tasker (1985) has detailed the accepted practices for constructing polygonal blocks of influerrce in the estimation of ore reserves. Further he suggests that users might fall into traps such as omission or overlap when determining the area of influence for each sample point.As an example of these types of errors Tasker (1985) describes under "Coverage ofthe Area" how 25 per cent of the exploration area will not be included in an equiangular triangular grid where hexagonal blocks of influence are used.The introductory suggestion of Tasker (1985) of "incorrect procedure" by Rudenno (1983) (and Armstrong (1983)) reiterated around the Figure 2a of Tasker (1985), is based on the brief description of the polygonal area of influence by Rudenno (1983). That description is not too different from that given by King, McMahon and Bujtor (1982).

Jan 1, 1985

By S Hapugoda, H Han, L Lu

Sinter quality depends heavily on the mineral phases, textures and physical structure of the sinter, which are formed upon solidification of the sinter melt. The interaction of sinter initial melt with its surrounding materials will impact the properties of the sinter melt and consequently the solidified structure and quality of resultant sinter. Spreading and penetration are two important phenomena dictating the interaction of the initial melt with its surrounding materials, such as nuclei and adhering fines. In the present study, the penetration behaviour of an initial melt into various natural iron ore substrates of different ore types during sintering was studied using a laboratory scale penetration testing procedure. The penetration depth and width were found to increase with temperature and vary with the type of iron ore due to their unique pore structure and mineralogical texture.

Nov 8, 2021

Mining had a very considerable effect on the country's development. The visual evidence remaining is an integral part of New Zealand history. Early mining for manganese and copper in the 1840s was succeeded by alluvial gold rushes. These gave way to hard rock extraction, hydraulic elevation and dredging. Coal mining dating from the 1850s was fairly widespread. Other minerals were obtained on a small scale. Manufacture of mining' machinery stimulated industrial engineering enterprises. Schools of mines played a significant part in advancing technical skills and several remain as museums. Surviving mine structures and site relics are part of the industrial heritage signifying the technological and economic development of a small isolated nation. Some of these are described. Identification, recording and preservation where practicable is advocated.

Jan 1, 1990

By R Dimitrakopoulos, I Minniakhmetov

Geostatistical simulation techniques are used to quantify uncertainty of spatial attributes of interest describing mineral deposits, petroleum reservoirs, hydrogeological horizons, environmental contaminants and so on. The majority of existing methods consider second-order spatial statistics and Gaussian processes, while the more advanced multiple point-based simulation approaches are algorithmic and do not consistently account for the high-order spatial relations in data. Recently, simulation techniques for complex and non-Gaussian spatially distributed variables have been developed, based on high-order spatial cumulants, and make no assumptions on data distribution or require data transformations. In this paper, the previous developments are extended and a new approach for the joint simulation of multiple correlated variables using high-order spatial statistics is proposed. The technique is based on a new algorithm for the decorrelation of correlated variables into factors, using the so-termed diagonal domination condition of high-order cumulants. The decorrelated factors are then simulated using high-order simulation and back-transformed into the initial correlated variables. The decorrelation using diagonal domination of high-order statistics is tested with a data set from a multielement iron ore deposit, and then a fully known two-dimensional data set with two correlated variables is used to demonstrate the practical intricacies of the proposed method.CITATION:Minniakhmetov, I and Dimitrakopoulos, R, 2014. Joint simulation of correlated variables using high-order spatial statistics for orebody modelling, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 53–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

Applications of chlorine metallurgy to the extraction of metals often result in the production of volatile metallic chlorides, most of which condense directly to a solid phase at 1 atm pressure. A stirred-bed condenser suitable for the recovery of these materials is described.The unit, developed from the concept of a fluid bed condenser, has the advantages of versatility of operation and ability to control fog and dust formation. Test work using aluminium chloride vapour (as an example of a volatile chloride) gave recoveries approaching 100 per cent. The yield was dependent upon halide content of the vapour, flowrate, and, to a lesser extent, upon coolant temperature. Analysis of the heat transfer dataindicated condensation side coefficients in the range 10 to 30 B.T.U./hr sq. ft. 0p.

Jan 1, 1971

By Van Hoorn PD

For the development of BHP's Gregory open cut coal mine in Central Queensland a mini computer was successfully used to assist staff in the evaluation of the deposit and the planning of the mine. The Gregory deposit is essentially a single mineable seam deposit, however the systems developed may be applied to other coal deposits including multi seam occurences. The first phase of the Gregory computer evaluation and planning project involved the establishment of a borehole data base for the storage, retrieval and analysis of both strata and quality data. During the second phase a numeric block model of the coal deposit was created. Using this model reserve calculations were carried out by specifying the area with the aid of a digitizing tablet. The third phase involved the develop- ment of systems to simulate the dragline stripping operations including the rehandle percentage calculation, a dragline production schedule showing coal quantity and quality exposed, and a combined multi dragline operation schedule that can produce figures and graphs for up to 20 variables. A derivative of the operating plan was a programme that gave productioh cost estimates

Jan 1, 1978

By S Harvey

An inrush of water or mud into an underground mine, or sudden subsidence above mining voids represent low probability but high impact risks in underground mining. About two such incidents involving multiple fatalities or loss of production are reported each year worldwide. On average, Australia experiences one such incident every three to four years. This paper reports the development of a Standard that is intended to eliminate fatalities due to inrushes and subsidence.

Jan 1, 1998

By Keren Z, Huanguo G, Jlchuan Q

In this paper, the authors introduce a new flotation technique, a double collection flotation precess, which succeeds in separating feldspar from quartz effectively in weak acidic medium (pH = 5-6). In the presence of sodium hexametaphosphase(HMP), sodium oleate selectively improves the floatability of feldspar in the first collection step. Dodecyl amine- hydrochloride is used as collector in the second collection step to separate feldspar from quartz. The flotation tests with pure minerals as well as artificial mixture give out satisfactory results. The mechanism of reagent effect was investigated briefly, which is helpful for understanding the Process.

Jan 1, 1993

By Deutsch G. P

The output of an underground mine often depends entirely on the mine winding system. -Decisions made--at the design stage affect the economy and operation'of the mine'.througb -its entire life. A modern mine winding installation is an integrated system and its design requires a multidisciplinary approach including expertise in the-materials handling, mining, mechanical, civil, structural, electrical and control engineering fields. The paper-sets out the elements of typical mine wind- ing systems-and describes some of the more important decisions which must be made during the planning and design process, It is no longer.adequate to. base the choice of a system on the pre- ferences and experiences of individuals. Major Australian winding install- ations are usually designed on the basis of overseas experience and some of the detail design is often carried, out overseas. Differences in basic design criteria occur from country to

Jan 1, 1973

By A Purvee, M F. Lee, L J. Mollison

Oyu Tolgoi is a large Cu-Au porphyry deposit in the south Gobi desert, Mongolia. The first of several deep, large-diameter, concrete-lined shafts, Shaft 1, is nearing completion. It will have a finished depth of 1380 m at a diameter of 6.7 m. These shafts will provide access to and hoisting capacity for block caving of deep underground ore. Geotechnical site investigations, and associated predictions of stability and ground support requirements, are compared against actual construction performance. Routine mapping is essential, along with checks against predictions and informing the contractor of ground conditions and variances.Advance rates are compared against predicted rock mass quality. A reasonable correlation exists between Qwall and advance rate. Overbreak and concrete liner thickness is related to the blockiness quotient, RQD/Jn.A ætool-bagÆ of just a few support elements (chain-link mesh, fibrecrete and 2.4 m long friction anchors and resin grouted re-bar bolts) was able to cope with the ground conditions encountered. QA/QC procedures are essential from the factory, through site storage to installation.

Jan 1, 2008

By J Chen

Research conducted into backfill drainage at Mount Isa Mines since 1992 is described. Piping in draining backfilled stopes has been the primary cause of bulkhead failures and emphasis is placed on research into the piping mechanism. Laboratory and in situ tests aimed at understanding the piping mechanism have been conducted and the results are presented. A case history of piping in a draining bench stope fill mass is described and a technique for reducing the potential for bulkhead failures in bench stopes is presented. Hydraulic fill is produced by standard cycloning of tailings and the overflow (reject material) is sent to thickeners prior to placement in the tailings dams. Research into the partial introduction of thickener underflow into the backfill system and its influence on backfill drainage is also described.

Jan 1, 1998

By Dorricott M. G

Ballarat Goldfields NL is developing an exploration decline at Ballarat East using a Mitsui Miike S-125 roadheader. To-date, 530 in of advance has been achieved at an average rate of 16.1 m/week. Roadheader availability has averaged 94.3 per cent, and pick consumption has averaged 0.016 per m. Ground support has involved pattern rockbolting with split sets, 100 mm thick fibre reinforced shotcrete, and steel sets as required. The slower than expected advance rate has mainly been due to difficult ground conditions. It is expected that a further 970 in of decline will be mechanically excavated before a drill and blast system becomes more economical.

Jan 1, 1995

By J O. Watson, V S. Vutukuri

This paper presents results of an investigation on acoustic emission characteristics of granite, sandstone and rock-like material in the unconfined compression and tensile tests. Both the acoustic emission signature and stress-stain curve are analysed in the experiments.The experimental results show that different acoustic emission characteristics are observed at different stress and deformation stages in unconfined compression and tensile testing. Extensive and unstable acoustic emission changes may be interpreted as indicating failure of the rock.

Jan 1, 1999

By P Ritchie, E H. Briese, N A. Currey

Kidston Gold Mines, located in semi-arid North Queensland, Australia is currently in its closure phase. Highly innovative and comprehensive rehabilitation strategies were employed at the site, including the direct revegetation of the surface of the tailings storage; the construction of a tailings sediment entrapment pond; the construction of a spillway to drain large rainfall events from the surface of the tailings; the construction of store/release covers over the tops of the waste rock dumps; the sheeting with oxide waste rock of the waste rock dump slopes; the partial back-filling of the initial Wises Hill Pit with waste rock and thickened tailings produced from the subsequent Eldridge Pit; the partial flooding of Eldridge Pit following the end of mining; and the construction of wetland systems to treat contaminated tailings and waste rock dump seepage. These closure strategies involved the careful consideration of water management. Specific water management issues included understanding the water balance of the tailings dam; the operation of the tailings dam sediment entrapment pond and spillway; understanding the water balance of the store/release waste rock dump covers; the importance and sustainability of vegetation on the tailings, store/release waste rock dump covers, and on the sheeted waste rock dump slopes; the level and quality of water in the partially flooded Eldridge Pit; and the treatment of contaminated seepage in the constructed wetlands. The seasonal and highly variable rainfall experienced in this semi-arid climate posed a number of challenges for the management of water on the site post-closure. The paper details these challenges and highlights how they were resolved over the period leading up to and following the end of mining.

Jan 1, 2003

The mineral sands industry in Australia can contribute much more sig- nificantly to economic development beyond the year 2000 by increased production of constituent minerals such as ilmenite, zircon, rutile, leu- coxene and monazite from existing and new resources, and especially from downstream processing to intermediate and finished products based on these resources. The end-use areas for mineral sand-based products include those products whose demand is tied to general economic growth, such as paints and plastics, and refractory bricks for the steel industry. High techno- logy applications such as zirconia ceramics and super-magnets are indica- tive of new developments in technology which provide considerable scope for expansion at higher rates than overall western world economic growth. An optimistic outlook for the industry is outlined, based upon a brief review of opportunities.

Jan 1, 1988

By Zhou Y, Karmis M, Haycocks C

Hazard analysis utilizes interaction mecha- nisms in combination with geologic, structural and mining conditions to delineate areas of potential damage in seams subject to interaction. Using characterizations of conditions peculiar to multi- seam mining, such as innerburden thickness, geol- ogy and structures, initial interaction contour maps can be constructed. Geologic hazard analysis is then carried out on roof, pillar and floor condi- tions in the affected seam using lower seam rock properties and layout geometries in the overlying seam. Either safety factors or damage ratings can then be developed representing degree of hazard in the lower seam. The final hazard map shows both the aerial extent and magnitude of potential dam- age from interaction.

Jan 1, 1992

Author Biography William Poole was born in Sydney, NSW in August 1868. He was educated at Sydney Grammar School. William spent two and a half years as a cadet in the Railway Construction Branch of the NSW Department of Public Works doing office and field work. He then undertook a civil engineering course at Sydney University. Following this he was employed for six years as assistant and resident engineer at the Water Conservation Branch, NSW and was in responsible charge of various field operations, surveys, river gaugings and works of constructions including a large timber weir and also a concrete weir on the Macquarie River, NSW. He then undertook a mining and metallurgical course at Sydney University and became a graduate (BE) with honours in civil engineering, mining engineering and metallurgy. He then spent four and a half years with BHP Co, one and a half years at Broken Hill in the mining and concentration works and three years at the smelting works in Port Pirie, SA, in the latter case he was metallurgist and night superintendent and during that time had responsibility and control at night of the blast furnaces and, during the last 15 months, of the whole of these large works. The author left the Port Pirie, SA works to assume the position of Director of the State School of Mines at Charters Towers and had responsible control of the establishment and also lectured in mining, surveying and structure. William Poole was honoured to hold membership in the following organisations: Assoc M Inst C E, L S of NSW, M Aus Inst M M, Assoc Inst M & M (London).

Jan 1, 2006

By M Araos, I Onederra

A novel explosive formulation that substitutes the use of ammonium nitrate (AN) with hydrogen peroxide (HP) as the main oxidising agent has been developed and tested as part of an Australian Coal Industry Research Program (ACARP) project. The main objective was to provide a step-change solution that has the potential to completely eliminate NOx fumes in blasting. The development of this HP/fuel-based explosive started with a comprehensive detonation characterisation program, consisting of unconfined velocity of detonation (VOD) measurements of samples at different diameters, densities and void sensitisation techniques. VOD results showed that the HP/fuel-based explosive mixtures behaved similarly to non-ideal commercial explosives; in that way mixtures could be tailored to achieve specific detonation performance targets. The next stage of testing in this development involved preliminary confined tests to evaluate the rock breakage potential of the HP/fuel-based explosive mixtures. Fully instrumented single-hole tests were conducted in a limestone quarry. Results from these preliminary trials confirmed the rock breakage performance of HP/fuel-based explosive mixtures. The confined VOD measured in one of the tests was 5100 m/s in a 102 mm diameter blasthole at a density of 0.96 g/ml. The corresponding borehole pressure measurement of this HP charge was 2.61 GPa with a detonation temperature of 2921°C. Based on near-field accelerations, both HP and ANFO charges displayed similar attenuation characteristics in the test conditions. Post-blast observations indicated that the breakage performance of the HP mixtures clearly reflected the in-hole detonation performance measurements obtained, confirming the ability of these explosive mixtures to both fragment and effectively displace the rock mass under evaluation. Further research work continues with the future commissioning of a prototype mixing and delivery unit, the successful completion and analysis of data from multiple-hole trials, and further characterisation work associated with product stability, reliability and performance under different geotechnical conditions.CITATION:Onederra, I and Araos, M, 2015. Detonation and breakage performance of a hydrogen peroxide-based explosive formulation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 565–574 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Sasol Roche Blasting Services (SRBS) and its former owners have been in the process of developing and utilising low-density explosives over the last ten years. Many blasts have been fired in varying strata types in a number of mining operations. This has led to a good understanding of the product and the best methods to exploit its characteristics when designing blasts. Unlike some other low-density products, SoftLOAD« is a homogeneous mix that is easily handled and able to be loaded at high load rates. This paper discusses the physics of SoftLOAD« low-density explosives and how through correct utilisation, blasting outcomes can be significantly improved. It also touches on the various side benefits that can provide the blast designer with a more controlled blast.

Jan 1, 2004