Search Documents

By K Le Bron

Fatalities that occurred because of rock falls in off-reef excavations (excluding shafts) over the last three years range between ten per cent and 20 per cent of the total number of fatalities that have occurred due to rock falls in the South African mining industry. These rock falls, mostly exacerbated by blasting practices, occur because of failure on discontinuities within the rock mass. Among other reasons of their occurrence is insufficient support installation or the incorrect assessment of rock mass conditions. This report presents qualitative analysis intended to outline rock stability conditions in tunnels subjected to dynamic loading. Seismic waves including those created by firing an explosive charge in tunnel rocks are considered. The rock behaviour is monitored using geophones and extensometers variably installed to record the near and far effects of roof bolt support units on a dynamically loaded rock. The paper discusses the results of field investigations.

Jan 1, 1999

The originally estimated mine life at Kidston (starting 1984) was 12 years. Through a continuing process of re-evaluation and improvement in the operation and by expanding the geological knowledge in the region, the mine life has been considerably extended. With falling grades and harder ore, the additional reserves have come with increasing risk - not only in an economic sense associated with diminishing profit margins but also operationally, requiring innovative milling technology and geotechnical designs to provide a lower cost environment for continued profitable mine production.

Jan 1, 1994

The working of alluvial deposits has from all times been a popular form of mining, not only from the simplieity of its operations, but also, in its more primitive stages, from the possibility of carrying it on without large capital, without skilled lahour, expensive plant, long terms of preparatory work, or, in fact, any other requisite than a shovel, a dish, and a stout pair of arms. It is possibly one of the oldest industries, and probably, also, it has been one of the most profitable.In tbe Australian States the happy days of rid alluvial deposits, when gold was to be hltd for the shovelling, are now almost over. The lust for gold has caused almost every corner of the world to be ransacked, and the more easily earned wealth to he exhausted: for the most part there remain now those deposits only which are too poor to be profitably worked by means of the implements and methods of old times. But, though the deposits have become poorer, the keen inventiveness of man has devised means whereby such large quantIties can be treated at a cost so low that he can still make a profit out of them. In this article, out of the many means devised, three only will be referred to-viz., hydraulic sluicing, bucket dredging, and hydraulic dredging. All mining may be divided into three principal operations-1st, the breaking down and conveying of the ground to where it is to be treated for the recovery of the metallic values, 2nd, the treatment of the material for the recovery of those values; and, 3rd) the removal of the worthless material or tailings. In all mining the object is to effect these three processes for the least expenditure of money commensurate with the highest degree of efficiency.

Jan 1, 1907

By Fountain C. R

In April 1987, Mount Isa Mines Limited (MIM) commissioned an ISASMELT reactor to smelt 15t/h of copper concentrate at the Mount Isa Copper Smelter. This unit was based on the Sirosmelt lance technology and incorporated features proven in the Lead ISASMELT plant which has been operating in the MIM Lead Smelter since 1983. From April 1987 to June 1989, the copper smelting plant treated 167000 tonnes. Concentrate, coal and fluxes are fed continuously to the furnace. Oxygen enriched air is injected through a lance which is submerged in the slag bath. Matte and slag are tapped together through a single taphole into a reverberatory furnace, and from there are treated with normal reverberatory furnace production. Advantages of the process include its ability to eliminate most lead and arsenic in feed, its flexibility with respect to feed composition, sizing and moisture, and the plant's low capital cost. Acceptable refractory life has also been demonstrated. The commissioning of a 70 t/day oxygen plant has rerated the plant from 15t/h to 18t/h while allowing a reduction in fuel usage of one third. A trial using 150 t/day oxygen was carried out in May 1989, and showed that the furnace could treat 48 t/h chalcopyrite concentrate while maintaining a very low fuel requirement. The oxygen trial results have given considerable confidence for plant scale-up. Detailed project evaluation is currently underway for the replacement of the roaster and reverberatory furnaces at Mount Isa with a single 110 t/h ISASMELT reactor.

Jan 1, 1989

By M P. Schwarz

In recent years, computational fluid dynamic (CFD) modelling of mechanically stirred flotation cells has been used to study the complexity of the flow within the cells. In CFD modelling, the flotation cell is discretised into individual finite volumes where local values of flow properties are calculated. The flotation effect is studied as three subprocesses including collision, attachment and detachment. In the present work, these subprocesses are modelled in a laboratory flotation cell. The flotation kinetics involving a population balance for particles in a semi-batch process has been developed. From turbulent collision models, the local rates of bubble-particle encounters have been estimated from the local turbulent velocities. The probabilities of collision, adhesion and stabilisation have been calculated at each location in the flotation cell. The net rate of attachment, after accounting for detachments, has been used in the kinetic model involving transient CFD simulations with removal of bubble-particle aggregates to the froth layer. Comparison of the predicted fraction of particles remaining in the cell and the fraction of free particles to the total number of particles remaining in the cell indicates that the particle recovery rate to the pulp-froth interface is much slower than the net attachment rates. For the case studied, the results indicate that the bubbles are loaded with particles quite quickly, and that the bubble surface area flux is the limiting factor in the recovery rate at the froth interface. This explains why the relationship between flotation rate and bubble surface area flux is generally used as a criterion for designing flotation cells. The predicted flotation rate constants also indicate that fine and large particles do not float as well as intermediate sized particles of 120 - 240 ¦m range. This is consistent with the flotation recovery generally observed in flotation practice. The magnitude of the flotation rate constants obtained by CFD modelling indicates that transport rates of the bubble-particle aggregates to the froth layer contribute quite significantly to the overall flotation rate and this is likely to be the case especially in plant-scale equipment.

Jan 1, 2005

Just as Australia is part of the Pacific Rim, so the Pacific Rim should be viewed as part of the whole world. That applies in particular to that scarce commodity û money. There are five main factors of production in any mining development û mineralisation, materials, manpower, management and money. LetÆs focus on the upstream input û mineralisation, and the downstream input û money, especially in the area of communications. Unknown to many, the Competent Person reporting on Mineral Resources and Mineral Reserves has a direct and unavoidable impact on the companyÆs financial statements û the profit and loss account and balance sheet. With respect to reporting of the major asset of most mining companies û the resources/reserves û investors are getting a better deal now than at any time in memory as regards flow and adequacy of information. Australia has been a world leader in this regard. The outlook is for even more informative and useful reporting. The more rigorous reporting requirements for Exploration Results and Mineral Resources/Reserves, which have become a worldwide phenomenon over the last five years, will continue. This will be positive for the mining industry as a whole and for Australia in particular. However competition for the scarce investment dollar will also increase. Put simply, mining has many competitors, unconnected with mining, for the capture of the investment dollar. It behoves all participants to recognise that there are three investment factors which influence strongly the willingness of investors to put money into mining. These are Confidence, Credibility and Consistency. AustraliaÆs investment image stands high in these three respects, but the competition will continue to grow. AustraliaÆs lead must be maintained. However, some investment decisions should not necessarily be based on fundamental, quantifiable facors. Some of these are outlined.

Jan 1, 2004

The process of mine planning at AnacondaÆs nickel and cobalt laterite operation located at Murrin-Murrin in the Northern Goldfields of Western Australia is carried out in a number of stages in an endeavour to determine the optimum mining sequence in order to maintain supply to the 4 Mtpa plant subject to operational constraints. The 296 Mt @ 0.99 per cent Ni and 0.064 per cent Co ore reserve (based on a cut-off grade of 0.8 per cent Nickel) is spread geographically widely over three regions comprising Murrin North (15 km + 15 km), Murrin South (7 km + 16 km) and Murrin East (5 km + 13 km) (refer Figure 2). The nickel mineralisation has been broken up further within each region into 18 separate manageable block models representing the 32 different deposits. The models are based initially on the 50 m + 50 m resource drilling for long term planning and updated with 12.5 m + 12.5 m grade control drilling prior to mining. Each of the individual block models are optimised using Whittle 4X software to provide the shells used as the basis for each of the 126 pit designs. The pits are generally nested with starter pits targeting the higher value shells with subsequent pits incrementally cutting back ultimately to the life of mine shells. A series of steps including: the coding of the individual pits into the block model; data export; TCL scripting (to calculate additional economic and tracking information); importing; and re-blocking; completes the transfer of the data into a MineMax (mixed integer linear programming schedule optimising software) model. Using MineMax and the application of operational and production constraints allows the optimisation, assessment and economic evaluation of alternative scenarios in order to determine the optimum life of mine plan and schedule.

Jan 1, 2003

Solid EnergyÆs project evaluation process utilises a standard staged gate approach, with five levels leading ultimately to project execution (level 6). For a project to progress through each level, specific financial criteria need to be satisfied. Solid Energy primarily use value based (discounted cash flow) metrics to support investment decisions. Within this approach Solid Energy utilise a number risk-based techniques to quantify project uncertainty. This includes the use of risk-based probabilistic analysis using Monte Carlo simulation and probability-based scenario analysis. Figure 1 shows the net present value (NPV) cumulative probability. Project risks are identified through comprehensive risk workshops. The output of these workshops (list of key risks, ranges of uncertainty and probability of occurrence), is quantified within the financial models. Incorporating this risk information on a probabilistic basis allows an investment decision to be made with a robust knowledge of the range of possible project outcomes along with the likelihood (probability) of those outcomes occurring, for example 80 per cent confidence that the project value will be greater than NZ$10 M, 50 per cent confident it will be greater than NZ$50 M and ten per cent confident it will be greater than NZ$70 M. Incorporating risk implicitly into the financial analysis allows the business to easily evaluate/measure projects with different risk profiles. The detailed risk analysis does away with the complexity of arbitrary risk-based hurdle (discount) rates, as projects can be evaluated based on their specific risk characteristics. Whether a project will progress to the next level of investment and ultimately into implementation depends firstly on the value assessment in comparison with the associated risk/uncertainty, and secondly matching this with the businesses appetite for risk. At Solid Energy standard criteria are used for specific project evaluations, but in addition projects are considered on a portfolio or strategic basis also. Solid Energy attempts to maintain a mix of low risk (low value) projects with some high risk (high value) opportunities. The mix of projects must remain in line with the shareholdersÆ risk appetite. One of the keys to a successful investment decision is ensuring that the appropriate information is available to decision-makers so that they may proceed with a comprehensive understanding of the risks and impacts associated with the decision.

Jan 1, 2007

By C J. Stanley

Reflected light optical microscopy, or epimicroscopy, is one of the oldest techniques of modern mineralogy. At a relatively low capital cost, it is also very resourceful, and the analytical choice for the identification of most ore minerals. In ore mineralogy, reflected light optical images have the potential to overcome the main limitation of backscattered electron images from scanning electron microscopes, namely contrast of mean atomic number  below the spectral resolution of the backscattered electrons detector. This is the case for relevant ores, like iron (haematite-magnetite) and copper-zinc ores (sphalerite-bornite), but for both cases the pairs of minerals are easily discriminated in reflected light. The improvements in optics and electronics also made microscopy a powerful source of digital images, suitable for automated analysis for minerals processing, as the determination of liberation spectra. The drawback, however, has always been the impossibility to recognise the transparent minerals, which account for most of the gangue phases in ores, from the embedding resin, usually epoxy. In order to determine if there was any possibility to separate quartz from epoxy resins, reflectance spectra have been acquired for quartz and some commercial epoxy resins (Araldite, BuehlerÆs Epothin and Epocolor, Araldite spiked with fluorochrome from Struers), from 380 to 720 nm in 5 nm intervals. Reflectance of quartz and epoxy is very similar over the whole visible light range, and varies from 4.5 to five per cent. Epocolor, a red-dyed epoxy, reflects slightly more above 560 nm, as does Araldite spiked with the fluorochrome from 460 to 570, but for both the reflectance is still very close to that of quartz, under 5.1 per cent. This data set is final, and precludes the application of reflectance in light optical image analysis for assessment of liberation, phase quantification, or any other signal that requires separation of resin from transparent minerals.

Jan 1, 2008

By M T Roche

The Cannington deposit is one of the largest accumulations of silver-lead known. Located 135 km southeast of Cloncurry in North West Queensland (Figure 1), Australia, the deposit is currently in the feasibility stage of its development. The deposit is named after the nearby Cannington Pastoral Property which runs some 25 000 sheep on 'downs' country. The investigations of the Cannington deposit are carried out under the authority of Mineral Development Licences 139 and 144 and Exploration Permit for Minerals 6788, Answer Downs. Exploration for Broken Hill Type (BHT) silver-lead-zinc deposits in the Mt Isa region has been undertaken by The Broken Hill Proprietary Company Limited's Minerals Division (BHPM) since the early 1980s following in-house research which showed that the Eastern Succession of the Mt Isa Block exhibits characteristics which were favourable for hosting BHT

Jan 1, 1994

By C Nucifora, M Landers, J Jones, G Maddocks, K Mandaran, A Forbes, W Wilson, S Newman

Glencore’s Mount Isa Mines Limited (MIM) operates the Mount Isa open cut and underground copper (Cu) and zinc-lead (Zn/Pb) mines near Mount Isa in Queensland, Australia. Tailings from processed Cu and Zn-Pb ore is contained in a 1,315 ha shallow (< 35 m deep) multi-cell valley fill tailings storage facility (TSF). Static geochemical testing conducted by MIM over the life of mine (LoM) verifies that the Cu, and Zn-Pb tailings has a wide range in sulfide content and diverse mineralogy with significant acid neutralising capacity (ANC) in some samples. The tailings are predominantly classified as potentially acid forming (PAF) using static analytical methods. Kinetic leach testing using free draining columns and humidity cell tests simulating tailings placed on the surface of the TSF suggest that the tailings samples are likely to remain non-acid forming (NAF) for 10 to 40 years under aerial exposure, and much longer than this under saturated conditions within the TSF. During this period of weathering, as ANC is depleted, the neutral pH drainage may contain elevated concentrations of some elements including sulfate, manganese and zinc. Only when the ANC is depleted would the tailings then begin to produce acid drainage. CITATION:Mandaran, K, Jones, J, Nucifora, C, Maddocks, G, Landers, M, Forbes, A, Wilson, W and Newman, S, 2018. Mount Isa Mines Rehabilitation Materials Sampling and Analysis program for closure planning, in Proceedings Life-of-Mine 2018, pp 138–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By J Gutzmer

The Kalahari Manganese Deposit in South Africa accounts for 80 per cent of the worldÆs land-based mineable Mn reserves. Although the ores are primarily mined for export, South Africa is the worldÆs third largest producer of ferromanganese and ferrosilicomanganese alloy, both of which are derived from the smelting of these ores. Mineralogical analysis has traditionally been forsaken for bulk chemical assaying in quality control of smelter feeds, principally because quantitative data could not be easily produced. Yet, mineralogy plays a vital role in determining smelting behaviour, which in turn has economic implications when aspects such as energy and reductant consumption are considered. Smelting is an endothermic process, and the amount of energy input required is dependent on the minerals present in the ore, as well as their relative proportions. Further, knowing the bulk Mn oxidation state in the ores allows for calculation of the amount of oxygen that must be driven off to produce alloy, and hence the amount of reductant required. Additionally, certain minerals can be correlated with potentially deleterious elements, so that ore mineralogy can indicate penalty element distribution. Mineral abundance analysis was conducted on ores from the Kalahari Manganese Deposit using quantitative X-ray powder diffraction. Rietveld refinement using a fundamental parameters approach was applied to micronised ore samples. The mineral percentages obtained were validated using mineral chemical data together with bulk major element data derived from ICP-OES. Bulk oxidation state partitioning was then carried out knowing the Mn valence in the minerals. The results show potential for implementation of the proposed method on a smelting plant, where ore blending could be then implemented to achieve consistent feed compositions to smelters. Selective mining could also be undertaken to obtain desirable ore compositions for domestic or international markets.

Jan 1, 2008

By Luke K. A

Pressure on production at New Zealand China Clays has led to the development of a dewatering control loop for fine halloysite china clay. The development was based on the analysis of data from the automation of plate and frame filter presses. The analysis of the data has led to process changes, and the ability to quickly solve dewatering problems. As a result of control in the dewatering circuit press times have reduced on average 117% and output has increased proportionally.

Jan 1, 1989

Syferfontein Colliery, part of the Sasol group of companies which specialises in the field of petro-chemical production, was established in 1990. The mine is situated about 150 km east of Johannesburg, South Africa. Two coal seams are mined, utilising two 75 m3 draglines, shovels and a fleet of 177 ton rear dump trucks. The mine will reach its full production capacity of seven million tonnes per annum in 1992. During the planning period, prior to the establishment of the mine, management were confronted with the unstable socio-political environment in South Africa which could jeopardise the eventual success of the mine. They consequently conducted a strategic planning exercise to determine guidelines for mine planning to improve the chances of success in this unstable third world environment.The strategic guidelines formed the basis for specific actions taken during the planning and commissioning of the mine. Specific actions were taken in the field of operating cost, labour relations, working environment, logistics and the general environment. First results indicate that these actions have played a major role in the success of the mine to-date. This process can be utilised by others facing similar or even totally different uncertainties.

Jan 1, 1992

By N Trabelsi, D Bakun-Mazor, Y Ben-Ari

As part of a comprehensive project to develop a remote sensing tool for evaluating the mechanical properties of rocks, one must obtain a rapid indication of these properties using conventional field methods. A common method for evaluating the mechanical properties of rocks in the field is to use a Schmidt hammer, a portable device that measures the rebound (R) of a spring-loaded mass impacting against the rock surface. Since the 1960s many studies have been made to find empirical correlations between the R value measured by the Schmidt hammer and mechanical and physical properties such as uniaxial compressive strength (UCS), elastic modulus, density, and porosity. Despite the existing correlations in the literature, this work is required to establish detailed empirical relationships for the carbonate rock units in Israel. To do so, 150 rock samples were collected from 38 different outcrops of carbonate rock units. In each outcrop, 20 impacts were made using a Schmidt hammer at different but adjacent points. The impacts were done horizontally perpendicular to the vertical rock walls. In the laboratory, we measured the density, effective porosity, water absorption, UCS, and elastic modulus. The rock samples we selected contained a wide range of UCS: from 7 to 270 MPa. Our empirical correlations indicate an exponential relationship between R and UCS and the elastic modulus, and linear relationships between R and density, porosity, and water absorbance. The most reliable index is the average of the five maximum impacts out of the 20 made in each rock outcrop. The correlation equations obtained from this work will make it possible to effectively evaluate the mechanical properties of the intact rock in the field, thereby aiding development of advanced tools for rock mass characterisation by means of remote sensing.

Nov 29, 2022

Hamersley Iron Pty. Limited has maintained an interest in the screening of iron ore fines (nominally -6 mm). However, no dry screening process had successfully demonstrated acceptable separating efficiencies at high tonnage rates, low operating costs, and mechanical reliability when screening iron ore fines (containing up to 6% free moisture) at sizes of around 1 to 2 mm. A new type of vibrating inclined screen has recently been developed which is claimed to have a non-blinding screening surface. It was decided to test a pilot scale unit in an existing pilot plant located at Hamersley's facilities at Dampier, Western Australia. The appropriate operating parameters such as vibration speed and feed rate were determined using one fine ore type. Mats with different aperture sizes, and different feed moisture contents were also tested. Trials were then conducted on various fine ore types to indicate the effect of different size distributions on separating efficiencies. The effects of feed moisture content were determined with these ore types, and a blend of lump (nominally -30+6 mm) and fines was tested to compare the screen's performance with that of the bottom deck of the minesite product Screens.

Jan 1, 1991

By A Torpy, N C. Wilson

Improvements in electron optics, field emission gun design, and X-ray detector technology have led to the development of a new class of microanalysis tools. By combining multiple wavelength dispersive (WD) spectrometers, spectral energy dispersive (ED) spectrometers and cathodoluminescence (CL) data sets, a wealth of information can be collected during routine electron beam mapping and analysis. In this paper, data collection on a field emission electron microprobe equipped with five wavelength dispersive, two silicon drift energy dispersive X-ray spectrometers and a wavelength dispersive linear array optical spectrometer has been automated with the optical, electron and X-ray signals being collected in parallel. To analyse the large hyperspectral data sets we have implemented an autoclustering strategy that can be used to produce a quantitative chemical phase map. The cathodoluminescence spectra can be deconvoluted to produce peak intensity maps, which are then converted into elemental speciation images with quantitative sensitivity down to parts per million levels. Both methods are illustrated using typical mineral processing examples, firstly a Ni-laterite sample is investigated with the fine-scale distribution of Ni examined in detail. Secondly, a scheelite sample with rare earth zoning in mapped and rare earth levels quantified.

Jan 1, 2008

The explosion of a charge in a drillhole sets the surrounding rock mass into vibrating stress wave motion. Except in the immediate vicinity of the drillhole, the dynamic stresses associated with this motion do damage only to pre-existing joints, cracks, or other weak planes, not to the rock material in between these. The joints are weak in tension, therefore the damage occurs as a result of tensile stresses. The initial damage process in the rock mass that ultimately breaks loose in front of the hole is similar to that in the remaining rock behind the drillhole. Recorded or calculated values of the vibration velocity and frequency contain a wealth of information about the combination of stress and strain that causes the damage. This paper outlines a new technique by which the peak strain energy derived from measured or calculated vibration velocity records is used to determine the local fragment size distribution. It combines two previously known and well tested techniques, namely the Holmberg-Persson calculation of the peak vibration velocity generated by an extended charge and King's calculations of the fragment size distribution as a function of the strain energy in rock crushing. Both of these calculations are based on experimental data and have been tested and found to agree well with actual conditions in their respective fields. Holmberg-Persson's calculated peak vibration velocities have been used successfully to predict and control damage to the remaining rock in cautious blasting, while King's calculation successfully describes the comminution of rock in mechanical crushing. Preliminary predictions of fragmentation in two types of rock blasting, a large hole open pit mining blast and a tunnel round, indicate that the new technique for fragmentation prediction has the potential for predicting fragment size distributions within the rock removed by the Blast.

Jan 1, 1995

One of the responsibilities of the Melbourne and Metropolitan Board of Works is to provide a sewerage system for the metropolis of Melbourne which now contains over 2.5 million people. In providing this sewerage system it was necessary for the Board to embark on a large tunnelling programme some 20 years ago. As a result of this extensive tunnel construction programme, tunnel boring machines and shaft sinking methods have been developed to cope with the soft ground and soft to medium rock found in the southern and eastern areas of Melbourne where the majority of the recent tunnelling has been carried out. While in the last few years radical changes in construction methods have not been made, development has continued and improvements have been made, which have enabled the Board to extend the limits of the ground conditions in which it can efficiently construct shafts and also tunnels with boring Machines.

Jan 1, 1976

This paper cites selected, prominent examples of current, major projects in Southern Africa in both the mining and civil fields. Differences and similarities in the life cycle of mining and civil projects are discussed. A closer relationship between the mining and civil fraternities is beginning to develop and should be encouraged because of the resultant exchange of experience and technology which benefits both disciplines. An attempt is made to assess future potential for new, major projects and trends in the implementation thereof.

Jan 1, 1999