Search Documents

A newly developed damage model was used in the study of rock fragmentation mechanisms involved in crater blasting. Simulations show that at the detonation of the explosive charge, a crushed zone around the explosive charge is formed due to compressive failure and then a strong pressure wave is sent out forming a pressurized ring that propagates at the dilatation wave velocity. As the pressurized ring leaves the crushed zone, two tensile stress components perpendicular to the radial stress are developed in response to the action of the radial pressure, causing tensile failure and forming a damage zone around the charge. The formation of this damage zone is quite independent of the depth of the explosive charge provided there is no interference by the reflection from the free face. When the pressurized ring reaches the free face, it is reflected there and causes rock failure on the ground surface that forms another damage zone. Under the simulation conditions, it is revealed that the depth of charge is a factor controlling the relationship between the two damage zones. At a depth smaller than the optimum, the two damage zones coalesce into one and there is excessive rock breakage; otherwise, the two damage zones tend to isolate from each other with the increase in the depth of charge. Calculations of fragmentation indicate that the average fragment size increases and the uniformity of fragments decreases when the depth of charge increases as observed in practical blasting.

Jan 1, 1998

By Doug Russell

Natsource: At a Glance l 160 employees l Global reach ? New York, Washington, Calgary, Ottawa, Toronto, London, Tokyo l Major Environmental Commodity Broker ? Rated as Top GHG Broker (Environmental Finance Magazine Survey, Dec. 2000 & 2001) ? Leading RECs Broker ? Large Broker of SO2, NOx l Large Energy Broker ? One of Highest Volume Gas Brokers ? Major Electricity Broker Overview l International Market l Implementing the Rate-Based Proposal l Assessment and Management of Risk from GHG Emissions Limitations

Nov 1, 2002

By M. A. Halim, V. I. Lakshmanan

Recycling is one of the key elements for sustainable process development for the recovery of value-added products and reducing environmental impact. Process Research ORTECH Inc. has developed several innovative and sustainable technologies, which minimizes the use of water, and chemicals for the recovery of gold, vanadium and gallium from secondary sources by maximizing the recycling of reagents, and reuse of water from process effluents.

Jan 1, 2015

By F. J. Reichhardt

Abstract -The Molopo Farms Complex is a major, layered ultramafic/mafic, early Proterozoic intrusion which is totally covered by sediments of the Karoo and Kalahari Formations and situated in southern Botswana and northeastern South Africa. The approximately 3000 m thick, generally fine- to medium-grained ultramafic and mafic cumulates are intrusive into equivalents of Transvaal Supergroup sediments and lavas. Multiphase deformation resulted in tilting and segmentation of the Complex into individual tectonic blocks. Sr isotopes document at least two chemically distinct parental liquids which interacted in a complex manner to form an approximately 1000 m thick rhythmically layered succession which straddles the ultramafic/mafic boundary. Repeated mixing resulted in a complex cryptic layering pattern and numerous sulfide-enriched layers which contain significant PGE +Au concentrations.

Jan 1, 1994

By I. Demers

The abandoned Manitou mine site covers an area of approximately 190 ha near Val d?Or, Quebec. This old site has been generating acid mine drainage for several decades. In 2006, a partnership was established between the Quebec Ministry of Ressources Naturelles (MRN) and Agnico-Eagle Mines to reclaim the Manitou site using tailings from the nearby Goldex mine. These neutral tailings were to be deposited on top of the Manitou site. An extensive study was performed to evaluate specific reclamation scenarios to control acid mine drainage using Goldex tailings as cover material. The article first describes the global approach used for this evaluation, which includes in-situ hydrogeological monitoring, tailings characterization, laboratory column tests, and numerical modelling. Of the thirteen column tests, three were conducted to evaluate the parameters affecting the performance of covers made of Goldex tailings placed over the spillage area of the Manitou site. Geochemical and hydrogeological parameters were assessed during the leaching column tests for almost two years. The tests aimed at evaluating the effect of water table level and monolayer cover thickness on the overall performance. The testing procedure involved monthly leaching and measurement of geochemical parameters. Results indicate that water table position is the most important factor affecting the monolayer cover performance to control AMD. Based on these results, it was established that the water table must be located near the interface between the Goldex and Manitou tailings to effectively reduce AMD generation. Cover thickness also has an impact on cover performance, which is however less significant than the water table position. The testing scenario with a water table located at the interface with a one-meter Goldex tailings cover showed progressive improvement in effluent quality.

Aug 1, 2013

By James Kear, Romain Prioul, Robert G. Jeffrey, Andrew P. Bunger, Dimitry Chuprakov

"Unconventional gas and geothermal reservoirs are typically naturally fractured and therefore the challenging problem of hydraulic fracture (HF) growth through naturally fractured rocks is an important issue especially for the development of accurate predictive HF models. This paper presents results from laboratory experiments in which HFs have been created in both sandstone and crystalline (gabbronorite) rock specimens such that they impinge either orthogonally or at an oblique angle on an unbonded, machined frictional interface. Depending on the conditions of each experiment, the fractures either cross or are blunted at the interface. The growth behavior was ascertained for these experiments based on a synthesis of the injection pressure record, active ultrasound monitoring, and direct post-experiment inspection of fractured specimens. From these experiments we observe: 1) A contrast between direct crossing and crossing with an offset for orthogonal and oblique intersection, respectively, 2) Apparent independence of crossing/blunting behavior on the friction coefficient for orthogonal intersection, 3) Dependence of the stresses required to promote crossing on the intersection angle between the HF and NF, 4) Existence of cases in which the hydraulic fracture crosses but then essentially ceases propagation such that all fluid is diverted to the interface. INTRODUCTIONHydraulic fracturing is a vital technology used to increase the productivity of oil, gas, and geothermal wells. Predicting hydraulic fracture (HF) growth is, in turn, critical to design of hydraulic fractures that grow to the desired length, accept the desired amount of proppant, and remain contained in the reservoir without unwanted height growth into surrounding layers (e.g. Economides and Nolte, 2000). The importance of HF modeling has prompted 6 decades of research during which simulators have become more efficient, more accurate, and have addressed a growing range of complexities (see review of e.g. Adachi et al., 2007).One of these complexities is the interaction between HFs and mechanical discontinuities such as natural fractures (NFs). Efforts in this area have been mainly driven by development of unconventional (i.e. low permeability) oil and gas resources because essentially all viable low permeability reservoirs, including shale gas/oil reservoirs, are naturally fractured to some degree (King, 2010). One of the most important questions for developing effective HF stimulation strategies in these reservoirs is whether the hydraulic fracture(s) is/are expected to be single-stranded or whether interaction with the NFs will lead to network-like growth. The basic building block for numerical simulators that can address this question (such as Kresse et al., 2013 and Weng et al., 2014) is whether an HF that intersects an NF will cross the NF or whether its growth will be captured by the NF so that additional fluid injection pressurizes the NF but does not generate ongoing growth of a new HF. These scenarios, including subcategories such as crossing with an offset, have been recognized for several decades (Daneshy, 1974; Warpinski and Teufel, 1987, and as recently reviewed and expanded by Chuprakov et al., 2013)."

Jan 1, 2015

RÉSUMÉ L’estimation la plus précise possible des coûts de minage est d’extrême importance pour les études de préfaisabilité afin de diminuer les risques financiers des projets miniers. Les méthodologies existantes d’évaluation des coûts de minage ne permettent pas de les évaluer avec des marges d’erreur acceptables tout au long de l’évolution des projets miniers. Elles visent à évaluer les coûts unitaires de minage des études préliminaires de faisabilité, pour les principales méthodes d’exploitation, en prenant pour l’hypothèse que ces coûts dépendent principalement du taux d’extraction journalière. Si cette hypothèse peut être justifiée pour l’évaluation du coût d’opération, elle est fort discutable pour l’évaluation des coûts de minage. Pour démontrer que cette hypothèse est inadéquate nous avons analysé la méthode d’exploitation la plus populaire sur le continent nord-américain c’est à dire celle par chambres vides avec retrait horizontal (Hr – Horizontal retreat), ou « Longhole » et celle avec retrait vertical (VCr - Vertical Crater retreat). Il ressort de cette analyse que les coûts unitaires de minage dépendent principalement des conditions géotechniques du massif rocheux et de la largeur du gisement et non pas du taux d’extraction journalière du minerai.

Jan 1, 2010

By P. Sauriol

This work addresses the design challenges and demonstrates the capabilities of a novel water transfer factor measurement apparatus. Several measurement concepts were screened on the basis of their water transfer factor accuracy using Monte-Carlo generated virtual experiments. The most promising measurement concept was assembled and tested to assess its actual measurement accuracy. For these concept validation experiments, the polymer electrolyte membrane fuel cell was simulated by adjusting the water injection rate to corresponding levels. Combining the anode and cathode measurements, the water transfer factor accuracy was typically better than 0.01. Real-time measurements of the water transfer factor on both anode and cathode sides of a polymer electrolyte membrane fuel cell were achieved. The anode and cathode side measurements were in good agreement with each other; however the anode side measurements were generally more reproducible. A parametric study showed that stream humidification plays an important part in the water transfer across the membrane electrode assembly. Finally the water transfer factor along the channel of a 300cm2 co-current fuel cell was obtained by using a series of six 50cm2 sub cells. The results were in good agreement with predictions from a recently proposed model.

Jan 1, 2005

By Taisuke Sakakibara, Shinya Suzuki, Tatsuya Kato, Chiharu Tokoro, Kenichi Muto

Surface complexation using a diffuse layer model were constructed for arsenic (As(V)), zinc (Zn(II)) and silicate (Si(IV)) for aluminum hydroxide in the co-precipitation process. From experimental investigations using isotherms, zeta potential measurement and XRD analysis, it was confirmed that co-precipitation involved not only surface complexation but also surface precipitation. However, surface complexation was major mechanism for As(V), Zn(II) and Si(IV) removal under the target removal level of the Japanese effluent standard. In surface complexation modeling, exchange capacity of aluminum hydroxide was determined from specific surface area obtained from experimental measurement and site density obtained from reference. Surface complexation coefficients were determined by fitting the removal property and sorption isotherm obtained from co-precipitation experiments. These parameters were in agreement with the numerical parameters found by Karamalidis and Dzombak (2010) who reported a database of adsorption equilibrium constants for gibbsite. The surface complexation models constructed in this study were applied to neutralization process of an actual AMD treatment. Our model could successfully represent the pH edges for As(V), Zn(II) and Si(IV) in the neutralization of AMD.

Jan 1, 2015

By J. Stiksma, R. Kalanchey, M. J. Collins, G. Owusu, R. Raudsepp, K. R. Buban, L. A. Barta, I. M. Masters

This paper describes the results of testwork for the treatment of Ambatovy laterite ore by a pressure acid leach process, with recovery of the soluble nickel and cobalt values as mixed sulphide intermediate by precipitation with hydrogen sulphide, and subsequent refining of the mixed sulphide to nickel and cobalt metals. These process development studies were carried out primarily in 2004, as part of a bankable feasibility study for the Ambatovy Nickel Project. The Ambatovy orebody is located in Madagascar. The mini pilot plant testwork was carried out in the Dynatec metallurgical laboratory in Fort Saskatchewan, Alberta. The results of the testwork were very encouraging, including nickel and cobalt extractions in the range of 95.5% to 97.0%, and 94.0% to 97.0%, respectively, in the ore leach step with sulphuric acid. High recoveries of nickel and cobalt were achieved throughout the remaining process steps, yielding separate nickel and cobalt metal powders with better than acceptable purity.

Jan 1, 2005

By A. G. Doll

"This paper expands the SAG mill survey database published by the Author at Procemin 2013. The new database includes 49 published SAG/AG mill surveys and includes mills from all over the world. The paper will compare the survey database to SAG mill models by Austin, Morrell and Hogg & Fuerstenau with the purpose of demonstrating the degree of fit of the models to surveys and validating any empirical “fitting factors” used in the models.SAG mill power draw models are used in mill design and grinding circuit modelling to predict how much power will be consumed by a particular mill geometry and operating configuration. The importance of conducting surveys suited to model calibration will be highlighted because the review of literature shows that survey information important to modelling is often missing or omitted. A recommendation for the collection of data during a mill survey is presented, along with some assumptions used by the Author in the absence of certain data. The benefit to mining companies of publishing their survey data, and thereby allowing modellers to improve their model calibration, is discussed.The comparison of models requires a discussion of the measurement of power in a mill drive system as the models use slightly different position in the electrical network for ""where power is measured"". The benchmarking of models against plant operations requires a similar discussion of power measurement."

Jan 1, 2016

By Ian S. Leslie

Seismic monitoring systems for mining operations are being utilized more than ever before in the characterization of rock mass response to underground and open pit mining. This paper provides a review of the use of microseismic monitoring for rock mechanics applications at mines throughout the world. Some practical considerations for the installation of these systems are presented along with techniques for optimizing seismic array coverage. Case studies and installation examples are also provided. Recent applications of advanced seismic analysis techniques are discussed including the determination of event mechanisms, mapping of maximum peak particle velocity (PPV) and seismic hazard fields, and the use of source parameter data for large event re-entry protocol.

Jun 1, 2012

By Shiqiang (Rob) Hui, Jiaren (Jimmy) Jiang, Rees Llewellyn, Yongsong Xie

Wear has been estimated to cost the Canadian mining/mineral processing industry over $15 billion per year mainly for repair/replacement of worn parts in 2013. The associated production loss is difficult to quantify but add considerably to the problem. The Canadian oil sands sector which has to deal with extremely abrasive and erosive solids, has traditionally incurred extremely severe and often unique attack. Demonstrable progress in mitigating the wear problems has been achieved through materials development, more informed materials selections, and better component and operation condition designs. An integral contributor to these advances is a long-term collaborative research partnership between NRC and the mining/supply industry. In this paper, this continuing collaboration will be described. A main focus is to identify degradation mechanisms occurring in the most severe and important service applications and to correlate these findings with laboratory test data. Relevant abrasion and erosion (often combined with corrosion) properties have been established and correlated with composition and microstructures for all classes of resistant materials ranging from relatively soft elastomers to ultra-hard ceramics. A comprehensive wear properties database has been compiled. This capability has been instrumental in facilitating the development of improved materials, optimizing materials fitness/selection for service, wear failure analysis, and quality assurance.

Jan 1, 2015

By R. M. Berry

A brief outline of refining methods used to (1) upgrade yellowcake to nuclear purity and (2) convert the uranium to the chemical and physical forms required by the fuel fabricators is presented. The uranium hexafluoride (UF6) production facility now under construction at Eldorado, Port Hope, is discussed. Technological improvements in uranium refining are considered.

Jan 1, 1969

By A. Romero, M. Carvalho, D. L. Millar

"The number of underground mines replacing diesel by battery powered mobile equipment is growing worldwide. The latter produces locally zero emissions and less heat, improving air quality in the working areas, and can potentially reduce energy costs due to lower ventilation requirements and in the face of higher fuel prices. However, there is a lack of systematic approaches to evaluate the potential economic benefit of switching from diesel mobile technologies to electric ones. This paper presents a method to answer the question of whether a mine with known operating conditions should invest in battery-powered electric equipment to reduce its total costs. Furthermore, this method provides the optimal number of electric and diesel equipment in relationship with their impact on the ventilation system and the total costs of running the mine from the energy perspective. A case study of an underground mine in Northern Ontario (Canada) is presented to validate the method proposed. The scenarios studied include the specific climatic conditions of the region, and the possibility to use heat recovery for the ventilation system. Overall, results show that the use of electric mobile plants is cost competitive, especially so when electricity cost can be lowered through load-shedding strategies.INTRODUCTIONOf the multiple advantages of using electrical vehicles (EV) underground in mining, the potential increase in air quality and comfort is the most significant (Paraszczak, Svedlund, Fytas, and Laflamme, 2014). Until recently, fully battery-powered electrical underground heavy duty machinery (i.e., loaders or trucks) were not available, so that tethered and trolley assisted vehicles were the only electric alternatives to diesel powered vehicles (Bétournay et al., 2011). Today, several commercial battery-based alternatives are available (General Electric Fairchild, 2015; RDH Mining Equipment, 2015; Paraszczak et al., 2014). Operational details can be found in Ewing (2015). The main battery technology used (Lithium Iron Phosphate, LiFePO4, or LFP) was already anticipated in Bétournay et al. (2011) as a good candidate for these types of vehicles. More details on these batteries, along with state of the art and future perspectives can be found in Zubi, Dufo-López, Carvalho, and Pasaoglu, (2018)."

Jan 1, 2019

By S. Kelebek, B. Ingram, C. Gibson, T. MacNeil, M. Aghamirian

"The beneficiation and upgrading of pyrochlore from its ores is carried out through flotation. In industrial practice, upgrading is conducted in a two-stage flotation process in which pyrochlore flotation is carried out after gangue mineral pre-flotation (carbonate, silicate, sulphide or phosphate reverse flotation). In this study, the flotation of pyrochlore from a low grade carbonatite ore was performed at the laboratory scale following a two-stage flotation process in which carbonate minerals were floated in advance of niobium minerals. In parallel, a simplified flotation process was developed in which pyrochlore was floated directly from gangue minerals at increasingly acidic pH. Laboratory results indicated that both two-stage and direct flotation provided similar results in terms of niobium grade-recovery. Based on these results, a large scale, integrated pilot plant was conducted using a direct flotation flowsheet. While the elimination of reverse gangue flotation resulted in flowsheet simplification, the dissolution of carbonate minerals and the subsequent effect of dissolved cations on the floatability of pyrochlore added an element of complexity. A comparison of results from locked-cycle laboratory testing and pilot plant testing highlights the challenges of scaling up a complex flowsheet. A case is made for the direct flotation process and the key parameters to achieving success in large scale direct flotation of pyrochlore are discussed.INTRODUCTIONPyrochlore (Ca,Na)2Nb2O6(OH,F) is a niobium bearing mineral which has been the primary global source of niobium since the first pyrochlore mine commenced operations in the late 1960s (Gibson et al., 2015a). Preceding the discovery and development of high grade pyrochlore deposits in North and South America, the majority of global niobium supply came from gravity concentration operations of columbite (Fe,Mn)Nb2O6, across Africa (Perrault and Manker, 1981)."

Jan 1, 2016

ABSTRACT Inco’s Iron Ore Recovery Plant was operated by Inco from 1955 to 1980 near Sudbury, Ontario. As exposures to specific nickel substances have been associated with adverse respiratory endpoints it is important to understand processes giving rise to such substances. This manuscript discusses the process and equipment, the propensity for aerosol formation, and operational procedures used by Inco in roasting a pyrrhotite concentrate, reducing the nickel in the formed oxide, leaching the nickel in ammoniacal solution, purifying the resulting solution, making green or black NiO, and producing iron oxide pellets. Industrial hygiene measurements are also reported.

Jan 1, 2013

By H. W. Parsons

Several low-temperature, dry chlorination processes for the treatment of sulphide minerals are reviewed, in a chronological order. These processes include the following: the Swinburne-Ashcroft, Baker-Burwell, Maim, Comstock-Wescott (Aldermac) and the Mitterburg Mining Process. Dry chlorination investigations at the Canadian Mines Branch (now CANMET) and the U.S. Bureau of Mines are discussed, as is a proposed process by the South Africa National Institute for Metallurgy. The techniques used in the process are discussed, as are the shortcomings, problems and failures of the methods.

Jan 1, 1978

By M. B. Kime

"A set of experimental batch leaching tests studied the effect of pH, time, temperature, and stirring speed on the relative Cu, Co, Ni, and Fe leaching yields of an oxidized copper-cobalt ore sample in an aqueous hydrochloric acid solution. The results were statistically analyzed and modelled using the structural equation modelling method. Models showed that Cu, Co, and Ni leaching yields were strong functions of the leaching time and leaching temperature, whereas the Fe leaching yield depended on the leaching temperature, stirring speed, and pH. Under optimum leaching conditions yields were 99.8% Cu, 82.4% Co, 91.3% Ni, and 30.6% Fe.RÉSUMÉ Une série d’essais expérimentaux de lixiviation en bâchée ont été menés pour étudier l’effet du pH, de la durée d’attaque, de la température et de la vitesse de brassage sur les rendements relatifs de lixiviation du cuivre (Cu), du cobalt (Co), du nickel (Ni) et du fer (Fe) d’un échantillon de minerai de cuivre-cobalt oxydé dans une solution aqueuse d’acide chlorhydrique. Les résultats ont été analysés et modélisés statistiquement à l’aide de la méthode de modélisation par équation structurelle (SEM, de l’anglais structural equation modelling). Les modèles ont montré que les rendements de lixiviation du Cu, du Co et du Ni dépendaient énormément de la durée d’attaque et de la température de la lixiviation ; le rendement de lixiviation du Fe, quant à lui, dépendait de la température de la lixiviation, de la vitesse de brassage et du pH. Dans des conditions optimales de lixiviation, les rendements étaient de 99,8 % pour le Cu, de 82,4 % pour le Co, de 91,3 % pour le Ni et de 30,6 % pour le Fe. INTRODUCTIONThe Katanga province in the Democratic Republic of Congo hosts the northwestern part of the Central African Copperbelt. This region abounds with large, rich deposits of sulfide and oxidized copper-cobalt ores. In general, the main valuable minerals present are malachite (CuCO3Cu(OH)2) and heterogenite (CoO(OH)). Common impurities found in heterogenite are Cu, Ni, Si, Al, Mn, and Fe. The substitution of Co by other cations (e.g., Cu, Ni, and Fe) has an influence on the crystallinity of heterogenite (Deliens, 1974). In general, well-crystallized varieties of heterogenite have lower impurity contents, whereas amorphous heterogenite types usually contain more impurities (Thys et al., 2009). Further, in heterogenite, Co can occur in the 2+ and 3+ oxidation states. The gangue generally consists of quartz (SiO2), talc (Mg3Si4O10(OH)2), kaolinite (SiO2·Al2O3·2H2O), limonite (Fe2O3·3H2O), and goethite (FeO(OH)). Oxidized copper-cobalt ores are often treated by hydrometallurgical methods, whereas sulfide ores are often treated by flotation or pyrometallurgy, depending on their grades. Hydrometallurgical methods typically entail selectively dissolving the metals of interest (Cu, Co, and Ni) in aqueous solutions (leaching), transferring the dissolved metals to an organic solution, and retransferring these to a second aqueous solution (solvent extraction). Copper and nickel are readily dissolved in an acidic aqueous media. In contrast, cobalt is difficult to dissolve, especially if it is present in the third oxidation state; however, this species becomes soluble after it is reduced to Co2+ (Mwema, Mpoyo, & Kafumbila, 2002; Kime & Makgoale, 2016)."

Jan 1, 2017

By P. Hanniala, S. Harkki, B. Andersson

"The Outokumpu Flash Smelting Process was put into commercial operation in 1949. The original process was based on the use of preheated air. The adoption of oxygen enrichment of the flash smelting process air in 1971 was a crucial improvement, especially for smelter capacity. Oxygen use according to the Outokumpu method means selection of the most suitable oxygen content for the process air on the basis of the concentrate composition, capacity and matte grade. The furnace is not bound to only one fixed degree of process air oxygen enrichment; the oxygen content may vary from 21% to 100%.The degree of oxygen enrichment and the matte grade are the most important process parameters in reducing the operating costs of the whole system, including smelting, converting and acid production. Raising the matte grade allows more efficient use of the reaction heat in the smelting stage. Sulphur is recovered in a high-strength, constant-flow gas stream. The blowing time in the converters is reduced considerably.Oxygen enrichment and high matte grade improve the energy efficiency of the plant complex as long as the surplus heat from the system is not wasted. When the operating costs and investment expenditure of the total plant complex are taken into account, a reasonably high degree of oxygen enrichment (35-80°/0) is the best alternative in practice. Existing operating smelters have achieved single-stream thoughputs of over one million t/yr of concentrates.HistoryLocal capital and operating costs as well as lower energy consumption per unit of metal produced are now the crucial factors in determining the choice of process. In the late I940s, the same reasons prompted Outokumpu to develop the original flash smelting process in Finland. Between 1900 and 1940, very few technical changes in pyrometallurgical copper production took place. However, the commercial use of the flash smelting technique began a new era in metal extraction from sulphide concentrates. The characteristic feature of the method is that the concentrate is smelted in suspension: this offers the most favourable conditions for heat and mass transfer, and thus high reaction velocities. Outokumpu was the first to exploit the known advantages of flash smelting in a commercial installation at Harjavalta in 1949."

Jan 1, 1982