Search Documents

By William Petruk

Image analysis studies were performed on mill products from pilot-plant and laboratory tests that had been conducted to determine the effect of grinding media on the selective flotation of two zinc-lead-copper ores. It was found that, when the ores had been ground to the same degree of fineness with flint pebbles, ceramic pebbles or ore fragments (autogenous grinding) as with steel balls, there generally was increased sphalerite, chalcopyrite and galena liberation in the flotation feeds, depending on the textures of the minerals. The increased sphalerite liberation fully accounted for the improved zinc recoveries that were obtained when steel balls were replaced by either pebbles or ore fragments. The increased chalcopyrite and galena liberation accounted for part of the changed technical efficiency of concentration, but other factors, probably changes in oxidation and reduction of iron and in consumption of oxygen, also contributed.

Jan 1, 1977

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber plant was recently completed at an existing facility, in order to treat the sulphur dioxide off-gas emitted from rotary kilns. Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong operational readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.INTRODUCTIONCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Quebec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary byproductof the process.Fresh hydrated lime and CDS residue is captured by the dust collection system and is re-circulated to the CDS via a fluidised transport system. Clean off-gas passes through the dust-collection system and is then sent to the atmosphere by a single exhaust fan.The CDS residue purged from the system is combined with the dust collected from the kiln offgas system and this mixture is wetted in the already exiting agglomeration system, to minimize dust generation during handling, and then sent to disposal."

Jan 1, 2016

By J. A. Herbst

Professor Klaus Schönert and his students used fundamental physics to develop many of the principles required for the design and scale-up of "Gutt Bett Zerkleinern" devices such as the high pressure grinding roll (HPGR) or the high pressure roll crusher (HPRC). As the equipment evolved so have the tools used for its selection and analysis. In the current paper discrete element modeling (DEM), Metso's proprietary Fast Breakage simulations, and Schönert's packed bed piston test are combined with energy based population balance models (PBM) to yield an alternative to ore characterization and equipment selection by pilot plant testing. The resulting methodology is used to take the next step in understanding these devices with a view toward predicting plant performance. This paper describes a journey beginning with precise modeling of a small HPGR including stud geometry and system hydraulics. A key to predicting performance is the accurate modeling of individual particles, their motion in the machine, the probability of breakage and redistribution of fragments, and the inter-particle breakage events that occur between the rolls at different pressures, speeds and moisture levels. Advanced DEM simulations and particle breakage characterization methods provide the necessary technology. The resulting combined models were validated using a small diameter laboratory scale unit. The validated physics based model was used then used to predict the performance of plant scale units using a specific energy based scale-up method. Scale-up results are analyzed in terms of power draw, throughput, and discharge product size distribution.

Jan 1, 2012

By Lawrence Melis

Fission Uranium Corp.’s Triple R Uranium Deposit at its Patterson Lake South Project is located in northwest Saskatchewan in Canada’s Athabasca Basin. As part of pre-feasibility studies for the project a detailed metallurgical test program was completed to provide process design criteria. The testwork program encompassed preparation and analysis of test composites, comminution testing, uranium acid leaching, liquid-solid separation, solvent extraction of uranium, precipitation of uranium yellowcake products, tailings and effluent treatment, tailings physical and chemical characterization, and environmental testing of prepared tailings, as well as investigations of gold and silver recovery from the mineralization. The paper provides mineralogical information, testwork methodologies and test results which were used to arrive at process design criteria and the selection of the process flowsheet for the project.

Jan 1, 2020

By Jean-François Lessard

The performance of rock pass systems has a significant contribution to the economics of underground mines. Operational concerns include hang-ups due to arching of material, blockage and degradation of the rock pass. This papers presents the preliminary results of a comprehensive rock pass database on the engineering and operation of rock pass systems in Quebec underground mines.

May 1, 2002

By Dean McDonald

The Committee Bay Greenstone Belt extends over 300km and is one of the largest unexplored greenstone belts in North America with excellent gold and diamond potential. Committee Bay Resources Limited holds over 550,000 acres of land with prospective geology in the Committee Bay area southwest of Melville Peninsula, Nunavut. Committee Bay is a typical Archean greenstone belt comparable to the Yellowknife, Red Lake, Kirkland Lake and other prolific gold belts. Drilling during 2003 at Committee Bay resulted in: 1) the discovery of high-grade gold-bearing quartz veins with silicification and sulphidation at Three Bluffs, and 2) the continuation of high-grade gold mineralization in the hinge area of the iron formation at Inuk. Gold mineralization at Three Bluffs is identified in iron formation and adjacent sediments and has been traced by drilling for over 700m. The Three Bluffs iron formation is open to depth and along strike where is has been traced on surface for over 6km. In January 2004 Committee Bay and joint venture partner Gold Field?s announced a $7.1 million exploration program for the Committee Bay project in 2004. A total of 8,000m in exploration drilling has been approved for the expansion of the Three Bluffs to the resource stage and drilling of at least five new target areas. Additional mapping, sampling and geophysics will be used to identify new gold targets along the very prospective Committee Bay belt.

May 1, 2004

By Gorzalczynski. Stan

The recent trend in underground mine developments is ?big is better?. This is most certainly evident in the mine shaft and the conveyances that operate within its compartments. Today, there are several new installations requiring mine cages that can transport up to 170 passengers. The technology in mine hoisting is advancing to address a combination of higher capacity requirements, deeper hoisting depths and faster winding rates, however, some areas of the hoist plant have not changed for the past fifty years. The most notable of these areas is the shaft compartment guide string and the conveyance mounted safety arrest mechanism. The technology in use today for the protection of passengers in a shaft conveyance from a hoist rope severance incident, remains conceptually unchanged from Elisha Otis? design of 1850. The actual retardation components, the safety dogs, have taken on several forms since Elisha?s invention with the last major design change occurring in the late 1940?s. The arrest of a free falling shaft conveyance requires that the shaft guides withstand the energy imparted on them by the safety dogs. There are some very real limitations presented by the use of wood for this application. The new hoisting era will most certainly continue to demand larger capacity equipment but also, an increased awareness toward safety.

May 1, 2002

By J. A. Espinosa-Guillen, J. A. Lopez-Molina, S. García, J. A. Valencia-Quintanar

"The design and implementation of grouting treatments in rock masses are procedures that require continuous adjustment of parameters and criteria to optimize the results. In this proposal we describe a set of tools that enhance decision-making for this type of jobs particularly in dam projects. The methodology is focused on hydrogeological zoning of the site and its constant update combining engineer’s experience with artificial intelligence techniques to integrate the site knowledge; as well as the evaluation of grouting results for different scrutiny scales, with special attention on the relationship between water absorption and grout consumption. INTRODUCTIONSeveral methodologies for design, implementation and evaluation for grouting rock masses have been developed for the solution of specific problems and tested in diverse geological conditions. Each of these methodologies is focused on results evaluation for different scrutiny scales (Table 1) and is employed to assist decision-making before or during the grouting process.Some methods define specifications for grouting each stage of the borehole, making theoretical, semi empirical or experience-based considerations to define basic parameters as maximum pressure, maximum volume, grouting time, flow rate, etc. Ultimately each approach aim to optimize the injection process, adjusting volumes or the grouting time required to obtain satisfactory results, reducing risk of creating new flow paths or unnecessary grout travels, and enhancing the mixture properties to achieve adequate penetrability and long-term behaviour. Some of these criteria have been widely used in dam projects, for example the concept of Grouting Based on Facts to define the maximum pressure and volume (Ewert, 1997), the GIN method (Lombardi & Deere, 1993; El Tani, 2012), or the North American standards based on Apparent Lugeon measures (Naudts, 1995; Bruce 2011); on the other hand, there are relatively new criteria that have shown good results for dam grouting as the Aperture Control Method (Bonin et al., 2012; Carter et al., 2012) or the Real Time Grouting Control Method (Stille et al., 2012)."

Jan 1, 2015

By J. Lobel, M. Bourassa, J. A. Kozinski, B. Peng

Non-isothermal kinetics studies of the reduction phenomenon of electric arc furnace (EAF) dust generated in stainless steelmaking have been carried out. The dust was mixed with carbon as a reducing agent and dolomite as a binder to form pellets. A Thermo-Gravimetric Analyzer (TGA) was used to determine the weight loss of pellets heated at an average rate of 40 K/min. up to a temperature of 1500°C. The degree of metal reduction was calculated by considering the pellet weight loss, and evaporation of moisture, dust, zinc and lead at high temperature. The reduction process was divided into three different steps. The first covers the 300°C to 760°C temperature range (from 7 to 18 min.), the second step ranges between 760°C and 980°C (18 to 24 min.), and the third covers temperatures above 980°C. Each step is characterized by different chemical reactions. Non-isothermal reduction kinetics equations were set up to describe each step. The kinetics parameters such as apparent activation energies and frequency factors were established. It was found that the first step was chemically controlled, while the second step was diffusion-controlled. Reduction behaviour in the third step was strongly dependent on the initial carbon content in the pellet. Chromium oxide (CrO) could only be reduced in this last step. High temperatures and higher initial carbon content favoured the reduction of CrO.

Jan 1, 2001

By J. E. Shigley

The gemological properties that allow natural emeralds and blue sapphires to be distinguished from other gemstones are summarized in this paper. A variety of synthetic and laboratory-treated emeralds and blue sapphires are also encountered in the jewelry industry today. Gemologists distinguish these latter materials from their natural counterparts based primarily upon features seen with magnification, such as inclusions and/or growth zoning. In some cases, however, these observations and standard gem-testing methods are insufficient, and the use of non-destructive analytical methods, such as optical spectroscopy and chemical analysis, are required for positive identification. The commercial value of synthetic and treated gems are much less, and can be insignificant in comparison to that of an important untreated natural gemstone. Identification of synthetic and treated gem material is essential to maintaining integrity in the jewelry industry. Loss of consumer confidence in the gemstones sold at the jewelry counter could have a negative impact on the exploration and mining of natural emerald and blue sapphire.

Jan 1, 1998

By F. W. Brackebusch, R. O. Sack

"A method for determining the fineness of Au in electrum from the composition of fahlore coexisting with pyrite and chalcopyrite is presented. This method is based on previously published experimental brackets and activitycomposition models for electrum and fahlore, and it is potentially useful for defining temperatures of hydrothermal mineralization and retrograde evolution of precious metals deposits. The authors demonstrate that it successfully predicts compositions of electrum reported for this assemblage in the literature and illustrate its application for three gold-quartz vein deposits from the Coeur d’Alene mining district, Idaho, that are prospects of the New Jersey Mining Company, the Coleman vein, High-Grade prospect, and Silver Strand mine. Temperatures calculated from average electrum compositions estimated from gravity concentrates (molar Au/(Au+Ag) = 0.76-0.39) and from microprobe analyses of the fahlores (molar Ag/(Ag+Cu) = 0.039 ± 0.004, Zn/(Zn+Fe) = 0.57 ± 0.03, As/(As+Sb) = 0.23 ± 0.02) from the Coleman vein indicate that the electrums underwent retrograde re-equilibration to temperatures between about 80°C and 240°C, roughly 80°C below the temperature of hydrothermal mineralization and 10°C to 40°C above the temperature inferred for retrograde equilibration of Fe and Zn between sphalerite and fahlore. Fahlores from the High-Grade prospect [molar Ag/(Ag+Cu) = 0.009 ± 0.004, Zn/(Zn+Fe) = 0.55 ± 0.11, and As/(As+Sb) = 0.04 ± 0.03] and Silver Strand mineralized zone [molar Ag/(Ag+Cu) = 0.10 ± 0.04, Zn/(Zn+Fe) = 0.63 ± 0.02, and As/(As+Sb) = 0.06 ± 0.02] exhibit strong core to rim depletions in Ag due to retrograde operation of the reaction1/10Cu10Fe2Sb4S13 + Ag + FeS2 =Cu-fahlore electrum pyriteCuFeS2 + 1/10Ag10Fe2Sb4S13chalcopyrite Ag-fahlorewhich proceeds to the left with decreasing temperature. Electrum inclusions in arsenopyrite from the High-Grade prospect [molar Au/(Au+Ag) = 0.90 ± 0.02] define a minimum bound on the temperature of hydrothermal mineralization of 273°C, and the temperatureelectrum composition curve constructed for the most Ag-rich fahlore in the Silver Strand mine indicates that the fineness of its electrum is significantly less than in the other deposits."

Jan 1, 2004

By P. R. Stephenson

"The Australasian Code for Reporting of Mineral Resources and Ore Reserves (JORC Code) has been operating successfully for 14 years, and has an ancestry dating back over 30 years. Together with complementary developments in stock exchange listing rules, the Code has brought about substantially improved standards of public reporting by Australasian mining and exploration companies. The Code is regarded as a world leader in its field, and has been used as a basis for the development of resource/reserve reporting standards in other countries. The reasons for its success are varied, foremost among them being its adoption in full by the Australian and New Zealand stock exchanges, and the ability and willingness of mining industry organizations to bring Competent Persons to account when necessary.The latest revision of the JORC Code was undertaken in 2002-2003, based in part on releases of upgraded reporting standards in Canada, the United Kingdom/Western Europe, and South Africa, and the 2003 edition is expected to be released mid-year. Two of the more significant changes are: the introduction of a requirement for a Competent Person to be responsible for the documentation upon which Exploration Results are reported; and inclusion in the definition of a Competent Person of a reference to “Recognized Overseas Professional Organizations” being overseas professional organizations to which Competent Persons may belong for the purpose of preparing documentation for the submission of reports to the Australian Stock Exchange."

Jan 1, 2004

By Dean Millar

Clean, green, cheap compressed air can be produced efficiently and renewably by modernization of a 19th century technology ?The hydraulic air compressor has no moving parts ?After commissioning, the Ragged Chutes HAC operated for 70 years, only being stopped twice for repairs to the intake heads ?Operates using hydropower from Montreal river ?Produced air for ~29 silver mines in Cobalt, 20 km distant

May 1, 2013

By Yuyong Li, Liangman Zhang, Zhaolian Wang, Shun Wang, Ltd. Shandong Huate Magnet Technology Co., Fengliang Liu

"Introduce a newly revolutionary magnetic separator - Raising Concentrate Grade and Decreasing Dregs Content Magnetic Separator Series JCTN (i.e. RCG&DDC MS JCTN). HUATE® JCTN is designed for rinsing, purification, desliming and thickening of the magnetic minerals as per different requirements. Adopting 240°-270° larger magnetic element with multi-poles and magnetic pulsation, and combining the devices of multi-channel rinsing water and top flushing water and new style tank, HUATE® JCTN can improve another 2%-10% concentrate mFe% than the traditional MS without lowering the concentrate recovery rate. Thereby, it solves the uneasy concentrate upgradation problem of the traditional MS resulting from the magnetic aggregation. Now, JCTN has been successfully applied in more than 30 mines in Australia, China and Russia, e.g. Sino Iron of CITIC PACIFIC MINING MANAGERMENT PTY LTD. HUATE® JCTN can optimize the industrial processing line by: 1) improving the discarding rate before milling to discard the necessary tailing ASAP; 2) getting in advance the final concentrate after milling. One JCTN can replace many traditional MS in series. In some way, it can also replace the anti-flotation separation process.INTRODUCTIONWe’re writing to introduce a newly revolutionary magnetic separator - Raising Concentrate Grade and Decreasing Dregs Content Magnetic Separator Series JCTN (i.e. RCG&DDC MS JCTN). HUATE® JCTN is designed for rinsing, purification, desliming and thickening of the magnetic minerals as per different requirements."

Jan 1, 2016

By Xiu-Xiang Tao

This study investigated bio-liquefaction of lignite and its model compounds of thymol, bezioc acid and quinoline by a fungus, Hypocrea lixii AH. It analyzed, during bio-liquefaction, enzyme activity of oxidase, LiP, Lac, MnP and polyphenol oxidase, and degradation products by UV-Vis, FTIR, 13C NMR and GC-MS. The results showed that the bio-liquefaction percentage (by mass) of lignite was up to 44.86 %. The bio-liquefaction products of lignite were mainly aniline, amide, ether, carboxylic acid ketone and ester. The aromatic ring number was 1-3 with an aromatic carbon ratio of 0.328, which indicated rings opening, bonds breaking and oxidation reaction. By considering with the enzyme activity analysis results, it showed that LiP and Lac catalyzed reactions to open aromatic cycles and to break bonds; esterase to break ester bond; and peroxidase in oxidation reaction.

Aug 1, 2013

By H. C. Gunning

In spite of the fact that mining has been more or less active in the northern part of Vancouver island since the late 'nineties', there seems to be a remarkable lack of information regarding the nature and development of the region. Recently the operations at the Old Sport mine of the Coast Copper Company, Limited, and spectacular copper discoveries in the vicinity of Nimpkish lake, have directed the attention of the mining fraternity to the district. The writer spent the summer of 1929 making a reconnaissance examination of the general geology and mining properties of the area between Quatsino sound and Nimpkish lake, and he feels that a short paper describing the nature and mining possibilities of the region should be of interest at this time. A more detailed account of the ?geology and of the mining properties will be published in the forth- coming Summary Report of the Geological Survey. A short paper dealing with the Nimpkish Lake district was presented at the Annual Meeting of the British Columbia Division, held recently in Vancouver.

Jan 1, 1930

By Tim Gitzel

Thank you for your introduction, and thank you to the CIM for inviting me to make a presentation to you today. This is my first opportunity to report to you on the status of the Canadian uranium industry and I am pleased to tell you that the industry is in good shape, and well positioned for the future. As you will no doubt be aware, Saskatchewan benefits from the world?s largest known highgrade deposits of uranium as well as from a high level of provincial, public and northern community support. It is within this unique combination of geology and community that our industry operates. Uranium markets have been extremely competitive for a number of years for several reasons. First, deregulation in the nuclear electric power industry has tended to encourage fuel buyers to use up their large inventories built up at a time when rapidly increasing demand was anticipated. Second, alternate sources from surplus commercial stocks, military materials and reprocessed fuel have presented a major additional source of uranium supply. Today, these secondary supplies are meeting about half of uranium reactor feed requirements. Canada (that is, Saskatchewan) is the world?s largest ?natural? uranium producer with about a third of the global production. Saskatchewan?s mines produced more than 30 million pounds of yellowcake in 2002. Despite low prices, steady demand for uranium will continue. In fact, an increase in world uranium production in 2002 helped feed a more than 3 per cent increase in reactor fuel demand. Low cost production is important for surviving low market prices, but investments are based on longer-term strategies rather than simply responding to market cycles. Cost is not the only issue. In these times of increasing regulatory and public scrutiny we must continue to earn the trust of our stakeholders by adopting the highest standards and staying on the leading edge of technical, social and environmental developments. Managing these issues is as important as traditional concerns of ore grade and cost of production. The last two decades of the 20th century saw the Province of Saskatchewan rise to prominence as the leader in uranium production from facilities, which were at the time deemed world class. These facilities are now either at - or nearing - the end of their production years. We are now bringing on new facilities that will position Saskatchewan to remain the world leader in uranium production for many years to come.

May 1, 2003

By B. Grinbaum

The solvent extraction of Cu from acidic leach solutions is carried out using oxime extractants. The mechanism can be described as liquid ion exchange, where a labile H+ in the oxime replaces Cu++ ion from the pregnant leach solution. The process is reversible and, at high acidity, the copper is stripped back to the aqueous phase. As the extraction proceeds, the acidity of the aqueous phase increases and the equilibrium may shift against the extraction reaction. This phenomenon may become significant in leach solutions with high copper concentration, where large amounts of acid are transferred from the solvent into the aqueous phase. An efficient way to increase the recovery of copper consists of splitting the extraction into two circuits, and either neutralizing with lime or extracting the excess acid of the intermediate raffinate. In the second case, the acid can extracted using a solvent, which can be stripped with a base, e.g., NaOH or ammonia. A third option is direct neutralization with soluble basic salt, e.g., Na2CO3, within a single extraction battery. The choice of the preferred process depends on the specific process demands and on the relative availability and price of the raw materials and by-products price.

Jan 1, 2007

By S. B. V. Stewart, W. W. Forsyth

"Since the Mathew's method for open stope design was first proposed by Golder Associates in 1980 it has been applied at a number of mine sites in Canada. The initial hypothesis was based on a relatively small amount of data and the intervening period has allowed the collection of a significant amount of new data to test the validity of the method.This paper examines a brief history of the evolution of rock mass classification systems to provide background and emphasize their empirical and non-rigorous approach. It also presents the new data which appear to indicate that the initial hypothesis was reasonably good. The modification to the original graph proposed by Potvin is discussed as well as the applicability of the method to predicting the onset of caving. The original graph has been updated and has been subdivided into four zones described as ""stable""; ""potentially unstable""; ""potential major failure""; and ""potential caving"". The method is recommended as a useful open stoping design tool provided it is recognized that it is not a rigorous design method.Finally the paper proposes a recommended approach for application of the method by would-be users and addresses some typical pitfalls that may be encountered."

Jan 1, 1995

By J. G. A. Stevenson

GENERAL Location of Property THE Stirling zinc-lead-copper deposit is in Richmond county, Cape Breton, about a quarter of a mile southwest from Stirling P.O., and some 45 miles southwest from Sydney. The property is accessible by road for at least nine months of the year, and during the navigation period coastal boats maintain a service touching at the port of Fourchu, eleven miles from the mine. When flying conditions permit, the Cape Breton Flying Club, of Sydney, will carry passengers to or from the property, a service which has been particularly advantageous on two occasions when hospitalization was urgently required. The Company has mining rights on leases Nos. 73-74, 78-80, and 101-104, inclusive, and owns 166 acres at Stirling and one acre at Fourchu. The ore deposit is in lease No. 73. History The Stirling deposit was discovered in the 'nineties', probably about 1895. The original discovery is said to have been made in the bed of Copper creek, which traverses the ore-zone. For a number of years, indifferent development work was carried on with a view to copper production only, and it was not until1915-16 that attention was directed to the possible production of zinc. Previously, the ore had been considered too complex for metallurgical treatment. During the period 1916-24 several operators attempted to develop the property, among them being the Stirling Exploration Company, Stirling Mining & Smelting Company, New Jersey Zinc Company of New York, Hayden & Stone Company of Boston, and The Eastern Mining & Milling Company. Up to 1924, the work was limited mainly to trenching, stripping, ? diamond drilling, and shot drilling.

Jan 1, 1937