Search Documents

By David deVries, James Rajith, Paul Mascrenhas, Nurzhan Dyussekenov, Lawrence Hanschar

Kansanshi Copper Smelter commenced operation in March 2015. The smelter features four Peirce- Smith Converters (PSCs) operated in a three hot, two blowing configuration. This paper describes some of the process automation and design features implemented to maximize operational and environmental performance. To ensure that the converters were easy to operate, efficient, and were protected in emergency situations such as power failures or loss of tuyere air supply a significant focus was placed on automated sequences initiated by “one button” operator commands or otherwise automatically by the Distributed Control System (DCS). Examples include: main converter roll-in and roll-out sequences; emergency roll-out in the event of power failure; and the charging sequences for reagents (silica and reverts). Other automated features configured for the PSCs were specifically aimed at maximizing converter capacity and reducing the environmental impact from fugitive emissions. These features include: “one button” in-stack charging; automated restriction of blowing rate based on the available acid plant capacity; and fully-automated control logic for the Secondary Ventilation System. In-stack charging allows anode furnace oxide slag to be poured into the PSCs while the converters are still blowing and still sending off-gas to the acid plant. PSC Secondary Ventilation control logic was configured to require minimum input from the operators while ensuring maximum utilization of the available draft from the ventilation system. Highly automated PSC controls contribute to high utilization, averaging 41.2 in-stack hours per day. INTRODUCTION Kansanshi Copper Smelter (KCS) is located near Solwezi at Kansanshi copper mine in Zambia's Northwestern province. The smelter treats concentrate produced at Kansanshi mine as well as Sentinel mine located 150 km west of Solwezi. Four Peirce-Smith Converters (PSCs) are installed at KCS. The nominal capacity of each converter is to treat 350 t of copper matte and produce up to 250 t of blister copper per batch. Normally three PSCs are hot, with two able to operate (produce off-gas), and the third converter on hot standby. The fourth converter is normally under cold repairs. The blister charge size is relatively low for the matte charged due to the unavailability of tank house or other high copper scrap.

Jan 1, 2019

The New Zealand opportunity NZ?s only significant phosphate deposit 1 million tonnes imported annually - mostly from Morocco US $180/t + $75/t freight

May 1, 2013

Grinding with an electrochemically inert grinding media (i.e. high chrome white iron, or Magotteaux’s Duromax® alloys) shifts the pulp potentials to more oxidising conditions, increases the dissolved oxygen content and reduces the EDTA extractable iron concentration when compared with milling with electrochemically active grinding media (forged steel). These changes in pulp chemistry produce cleaner particle surfaces, reduce reagent consumption and increase concentrate grades and recoveries. This paper presents a robust laboratory test program that is able to not only demonstrates these effects but also provide an indication of the magnitude of the improvements that are possible. While laboratory studies are interesting, the proof is in the pudding! So, the paper provides an overview of plant trials conducted at a number of operations around the world, including: Newcrest’s Cadia Operation, Oz Minerals’ Prominent Hill Mine and Glencore’s Ernest Henry Mine. These successful plant trials clearly demonstrate that selection of the right grinding media alloy will yield savings in grinding media consumption and reagent consumption as well as increases in revenue through improved copper, gold and molybdenum recoveries. INTRODUCTION The key to a successful separation in mineral processing is the preparation of particles with adequate liberation under the correct pulp chemical conditions. While the importance of liberation on flotation separations is generally understood and well documented in the literature (Johnson, 1987; Jackson, Sutherland, Gottlieb & Quittner, 1989; Young, Pease, Johnson, & Munro, 1997; Greet and Freeman, 2000), the importance of pulp chemistry is more nebulous, particularly with regard to the impact of grinding media. Extensive work examining the electrochemical interactions between grinding media and sulphide minerals has been completed (for example, Iwasaki, Reid, Lex & Smith, 1983; Natarajan and Iwasaki, 1984; Yelloji Rao and Natarajan, 1989(a); Yelloji Rao and Natarajan, 1989(b)). Broadly, these studies indicate that most sulphide minerals are more noble than the grinding media used during comminution, therefore a galvanic couple between the media and the sulphide mineral(s) exists, which increases the corrosion rate of the grinding media. The corrosion products of the grinding media, iron oxy-hydroxide species, invariably precipitate on to the surfaces of the sulphide minerals thereby affecting their floatability (Johnson, 2002).

Jan 1, 2019

By T. P. Kostek

"Historically, gear pumps and motors have been popular in the mining industry because of their competitive cost, simple yet rugged construction, ease of rebuild, and relative long life and insensitivity to contamination. However, with the ever increasing ""popularity"" of fire-resistant hydraulic fluids, both users and manufacturers of gear equipment must make special considerations to enable the equipment to continue giving satisfactory performance even with the water-containing fluids.The paper discusses 60-40 invert emulsions and waterglycolsIntroductionMuch information has been published on the specific characteristics of the various types of fire-resistant hydraulic fluids. Fluid manufacturers' literature and other publications have dealt with such specifics as fire resistivity, seal compatibility and wear rate characteristics. Gear pumps and motors have been, and will continue to be, applied successfully in hydraulic systems employing both the ""invert"" emulsions (60-40) and water-glycols as the hydraulic fluid.Because most external spur gear equipment has been designed to function with petroleum oil as the fluid medium, certain guidelines must be followed to ensure satisfactory service life. FluidsThere are a number of different types of fluids which fall in the category of"" fire-resistant"" , the most common'being phosphate esters, water-in-oil emulsions, oil-in-water emulsions and water-glycols. The two in most prevalent use today as hydraulic fluids are the water-in-oil emulsions and the water glycols"

Jan 1, 1980

By C. -G. Berg, J. T. Tuominen

Since the beginning of the 20th century, energy efficiency in copper smelting has been improved by a factor of 30 as a result of adopting autogenous smelting processes with more and more efficient waste heat recovery systems, increasing use of oxygen enrichment and countless smaller improvements. Nevertheless, energy in the form of electricity and fuels continues to be the biggest contributor to smelter operating cost. Metallurgists around the world are under constant pressure to find ways to save those precious megajoules wherever they can. One area that is often neglected is the removal of water contained in concentrates. Copper flotation concentrates, as delivered to a smelter, typically contain some 8–12% moisture. This moisture must be removed and the only way to do this is by evaporation, which consumes a lot of energy. Several studies have shown that the most efficient way of removing this moisture is to use a steam- heated indirect dryer—the least efficient way being the feeding of wet concentrate directly into a smelting furnace. Even in the most efficient smelters that employ modern steam drying, the energy needed to remove the moisture from the concentrates constitutes over 15% of the total energy consumption of a smelter – acid plant complex. The major steps that have been taken in the past to lower the energy consumption of moisture removal are the use of drying in general and the adoption of steam drying. The energy efficiency of concentrate drying has been improved by 25% over the last 20 years. The latest giant leap in this area, the Kumera Heat Recovery Dryer, is the result of Kumera’s long-term development in improving the efficiency of concentrate drying. The Heat Recovery Dryer is a novel application of steam drying that uses the waste heat from dryer exhaust gas for drying concentrates, thus, cutting the energy consumption by a further 30%. This paper discusses energy consumption in copper smelting in general and analyzes the energy consumption of concentrate drying in detail. Different dryer types are compared especially from the perspectives of energy consumption and environmental emissions. Applicability of different energy sources for drying is evaluated and discussed. The principle of the Kumera Heat Recovery Dryer is presented along with results from extensive continuous pilot plant tests. Potential applications and the feasibility of Kumera Heat Recovery Drying technology are discussed.

Jan 1, 2019

By Pierre O'Dowd

"The southern Abitibi Belt is the major source of gold in Quebec. Although the northern part of the belt is quickly being developed, the area under study will not be downgraded in the near future because it still contains more than 75% of the known reserves in the belt.Gold is found in a variety of geological environments which are part of a small number of distinct structural patterns. For the exploration geologist, outlining such patterns might be easier and more productive than defining, when it is possible, the exact genetic nature of the gold mineralization.Exploring in the right place has always been one of the main concerns of explorationists. This paper briefly describes the various favourable geological settings, and outlines areas, types of structure and lithologies of high potential for gold exploration in the southern Abitibi Belt.IntroductionThe southern part of the Abitibi Belt is a profilic mining area for precious and base metals (Lulin 1990). Although mineralizing processes and controls of polymetallic deposits are well known and understood (Lydon 1984), almost every gold occurrence is a unique case and numerous models have been proposed (Roberts 1987; Hodgson and McGeehan 1982; Hodgson 1990).This study does not define new genetic models for the formation of gold deposits, neither is it meant to elaborate on the existing ones. A genetic approach, is by definition, theoretical and, to some extent, universal. It helps geologists define types of targets and exploration tools but does not outline or quantify target areas. To tentatively summarize the complexity of a genetic approach, a brief discussion on the various genetic models in vogue in Abitibi and the problems related to their use in exploration can be found at the end of this paper."

Jan 1, 1991

By Marc C. Betournay, John E. Udd

"In this study, the authors investigated the stabilities of slopes cut predominantly into Trenton limestone in a large quarry in the Montreal region. Analyses of the bench and pit walls indicated that small-scale toppling, ravelling, and wedge failures are the most likely modes of instabilities. Because most of the joints dip steeply, however, the conclusion was made that relatively high walls could probably be justified.The field investigations were supplemented with the determinations of the shearing strengths of artificial discontinuities that were cut into samples of the limestone. The properties of a fine-grained limestone were found to be influenced very much by the magnitudes of the loads that were applied, while the properties of a crystalline limestone were found to be much less, or not load-dependent.The study is one of a number that are being conducted in this area.IntroductionExtensive quarrying has been done in the sedimentary strata of the Montreal area for a very long time. By any standards, it can be said that the Island of Montreal is a major mining area. At present, approximately 20 quarries are being operated in, or near, the city of Montreal.In addition to the millions of tons of limestone that are removed each year, a large number of excavations for foundations are cut into the sedimentary rocks.To date, however, very little information has been published concerning the engineering properties of the local geological materials. No mention is made of this aspect in the references which are presently available.Because of this lack of information, the senior author has initiated a study in which the strength properties of most of the rock types, and of the natural discontinuities contained in these, would be investigated. To date, the results of one other investigation have been published and other work is in process. It is hoped that the end result will be a comprehensive knowledge of the important strength properties of all of the rocks in the entire region."

Jan 1, 1983

By Cesar H. Oboni

The development of specific risk-based methodologies to guide and prioritize clearing decisions in countries contaminated by Unexploded Ordnance and Land Mines (generically defined as Explosive Remnants of War: ERW) either at country-wide scale or road-network-scale was used in an unexpected way when a large mining company asked Riskope (www.riskope.com) to develop a multi-modal transportation network risk assessment plan, which included ocean going vessels, ports, wharves, railroad, trucking and other modes of transportation. What had been a first-in-the-world attempt in the humanitarian landmine clearing industry turned out to be extremely useful and equally innovative in the extractive corporate world. Instead of a country contaminated by man-made hazards such as Explosive Remnants of War (ERW) we were now dealing with a very complex multi-modal transportation system afflicted by all sorts of potential hazards from quakes to climate change, sabotage to labour strikes, and vulnerable infrastructures to potential energy crises. Interestingly enough the method developed to deal with ERW risk based clearing was also capable of solving the transportation risk evaluation problem, after necessary customization. This paper shows how ?out of the box? thinking and industry cross dissemination can bring significant evolution and a competitive edge even to unexpected areas of the world-wide mining industry. The results of the logistic system risk assessment shed new light on the management of the system, changed the way insurance coverage was purchased, and led to significant potential cost reductions in a period of global recession.

May 1, 2010

By F. Prescott, D. Hiam-Galvez, J. Hiam

Mines are frequently located in remote areas with little conventional employment and few opportunities for the existing population. The development and operation of the mines results in several years of intense activity followed by a near-complete reduction in employment and opportunities after the mines are closed. Designing Sustainable Prosperity (DSP) is a method for rectifying this situation by designing for long-term growth in areas that host mines. This process involves the participation of local and national governments, local community, mining companies, investors, academics and those with sector expertise. The mines will be the catalyst for regional sustainable development. If successful, long-term economic and environmental prosperity should be the result for the areas affected by mining and, in some instances, promoting the regions as centres of excellence for a particular industry. This paper will describe how the concept works using the copper producing region of Peru and Chile as an example. Designing sustainable prosperity starts by looking at regions based on the natural resources and skills available, the infrastructure and possible energy sources. Integrated natural resource models and innovative market studies, followed by education and skills requirements, are then established to determine the potential for the region and what needs to be done to realise the possibilities. INTRODUCTION Industry 4.0, or i4.0, dubs the fourth and current industrial revolution. Where previously they have been founded on ever-increasing consumption and production, i4.0 distinguishes itself by its partial focus on reducing resource intensity; lightweighting, energy efficiency, sensors and automation to improve resource efficiency. Industry 4.0 is an era of artificial intelligence, genome editing, biometrics, renewable energy, 3D printing, autonomous vehicles and the Internet of Things (Lu, 2017). These drivers represent key opportunities for the economic future of nations and regions.

Jan 1, 2019

By A. Mukherjee, C. Kelly, B. Markovich, G. E. Agar, G. E. Robertson, F. Khan, B. Shea

"Laboratory batch flotation tests were performed on a sample of bulk slow cooled converter matte (Cu:Ni = I) to optimize the time in each of the separation stages. Numerical simulations were carried out to estimate a continuous circuit material balance for the conditions selected. An experimental simulation of a continuous circuit (locked cycle test) readily came to steady state and there was reasonable agreement between the numerical and experimental results. The use of nitrogen as the flotation gas and the addition of collector to the grinding mill minimized the oxidation of chalcocite, which has previously resulted in increasing circulating loads, and led to a stable circuit with very low weights in the recycle streams.IntroductionINCO Limited developed a flotation process for separating the components of copper-nickel matte [Sproule, Harcourt and Rose 1945; Sproule, Harcourt and Renzoni 1960] in 1945 to replace the Orford process and continues to use the flotation process in almost the original mode to this day. Initially the matte processed was the result of smelting a nickel concentrate that analyzed about 12% nickel and 2% copper and all of the recycle material that was generated in the smelting process. The matte generated analyzed about 25% copper and 53% nickel, roughly 2: 1 nickel to copper. This matte was blown in Pierce-Smith converters to be sulfur deficient in order to produce a metallic phase that collected the precious metals contained in the smelter feed [Wilson and Stratton-Crawley 1991]. This process continued with little change until 1994 when the separation of chalcopyrite from pentlandite in the Copper Cliff mill was discontinued after 63 years of operation. As a consequence of the elimination of the primary separation of chalcopyrite from pentlandite in the milling process a bulk concentrate was produced for smelting. Bulk concentrate smelting came into practice in 1994 as part of the initiative to meet government legislation that restricted the emission of sulfur dioxide to the atmosphere. Previously, the copper concentrate was smelted in an INCO oxygen flash furnace which resulted in the capture of a high strength sulfur dioxide stream from which liquid sulfur dioxide was produced. Nickel concentrate was smelted in reverberatory furnaces that produced low strength sulfur dioxide gases which were difficult to treat. The action taken by INCO to meet the environmental constraints was to smelt a bulk concentrate in oxygen flash furnaces which would produce gases suitable for the production of liquid sulfur dioxide and another stream that was high enough in sulfur dioxide to be readily converted to sulfuric acid [Bell et al 1990]. The end result of this decision was that all the copper-nickel separation would be done in the matte separation plant."

Jan 1, 1996

By Ralph Harris, Javier Jara

"Oxygen is essential in gold cyanidation. It is supplied to the leaching media by sparging oxygen or compressed air into the cyanidation tank. The rate of oxygen transfer is critical to achieve the desired oxygen concentration in solution.The performance of a novel device for gas sparging recently developed at McGill University is compared to the mass transfer characteristics of the two spargers most used in the gold industry: the four lance configuration and the inverted cone. The distribution of gas and the kinetics of oxygen desorption of the three types of spargers was studied in a 140 litre tank. The oxygen dissolution of the new device is three to five times faster than the other spargers. This could increase the leaching rate and/or decrease the cyanide and oxygen consumption.IntroductionIn hydrometallurgical processing, it is often necessary to bubble gas through a pulp to carry out the wanted reactions. The gas can act to agitate the pulp and it can also supply reactant. The rates of the reactions which require a reactant supplied by the gas are often dependent on the rates of mass transfer from the gas to the solution.A common example of this is gold cyanidation which requires oxygen for gold dissolution. Since the gold containing slurry is rich in other oxygen consuming substances (sulphide like pyrrhotite), it is important to provide enough oxygen to allow complete gold dissolution within the residence time of the cyanidation reactors. It has been demonstrated that the rate of gold dissolution is directly proportional to the dissolved oxygen concentration of the pulp which in turn is proportional to the oxygen partial pressure in the bubble 1 2 3. Improving the rate of mass transfer of oxygen increases the dissolved oxygen concentration of the slurry and therefore improves the rate of the reaction.The rate of mass transfer from a bubble to its surrounding solution increases with decreasing bubble size and increasing gas bubble residence time which in turn increases with decreasing bubble size. The generation and dispersion of small bubbles is thus critical to achieving high rates of mass transfer. Different configurations and devices used to inject gas have different effects on the bubble size and the residence time, influencing the overall rate of mass transfer. Therefore better mass transfer can be achieved by adopting a more efficient method.The methods tested in this report are the four lance configuration (wall spargers), the inverted cone and a new device, designated HCD. The wall spargers and the inverted cone are used widely in the industry today."

Jan 1, 1994

By S. L. Gula

"Effective and timely communication during routine operations, and especially during emergency situations, is no easy task in any underground mine. At Cominco Fertilizers, Potash Operations, where 150people are employed underground to produce 3.1 million tonnes of potash per annum at a depth of 1100 m (3600ft), this is no exception. The over-all mine workings underlie an area of approximately 20 km 2 with average travel time to the active mining areas being approximately 30 to 40 minutes by light vehicle, and significantly longer than this for heavy equipment.In a mine of this size, the deployment and management of personnel and materials on a day-to-day basis, and during mine emergencies, is an important exercise. The Personal Emergency Device (PED) system has provided the Potash Division a means to achieve improvements in this area and reduce the communications bottleneck.The MineAt Cominco Fertilizers Potash Operations, approximately 30 km southwest of Saskatoon, the orebody is the same horizon being mined by other potash producers in the Saskatoon area and extends over 300 km in an east-west direction, and approximately 150 km in a north-south direction. Mining operations are carried out with approximately 150 employees operating on a continuous-shift basis, seven days a week.Mining is presently being done from Block 6 which takes the mine to its northernmost boundary and contains reserves of approximately 50 million tonnes. Production is from one level by five twin rotor continuous mining machines, each capable of cutting a face up to 5.5 m wide and 3.3 m high . All ore is transported to the shaft via approximately 20 km of conveyor where it is removed to surface by two 24 tonne skips.After the ore is conveyed to the mill for processing, the finished product is shipped by rail car or trucks to other parts of Canada, the United States or through Vancouver to other parts of the world."

Jan 1, 1993

By Tetsuya Yumoto, Toshikazu Shiratori

Information on the elements contained in E-Waste is important from the viewpoint of recycling. We analyzed several components of waste electrical and electronic equipment (WEEE) collected from citizens. The distributions of the minor metals in WEEE were determined with elemental mapping and chemical analyses. The annual change in elemental composition was investigated by analyzing equipment manufactured in different years. The information will be of use for separation techniques required for future advanced recycling.

Jan 1, 2011

By Richard P. Taylor, Rod Henham

Abstract - Newly discovered pegmatites distributed throughout the sub-surface environs of the Musselwhite Archean gold deposit occur as narrow dikes that intrude most of the major lithological units. The mineralogy and textures of the pegmatite dikes are characteristic of granitic pegmatites of the "Rare-Element Class"; more specifically, they closely resemble varieties of the "Complex-type" granitic pegmatites that are commonly associated with zones of tantalum mineralization. The essential minerals in the dikes comprise albite, quartz, and K-feldspar, together with lesser amounts of mica (including lepidolite), spessartine, tourmaline, and locally, spodumene. Fine-grained (30 µm to 300 µm), tantalum-bearing minerals occur in the quartzo-feldspathic matrix of the dikes as disseminations, in interstices, and in small vugs. The nature of the tantalum-bearing mineral assemblage present in individual pegmatite dikes varies from a simple mineral assemblage composed of ferrocolumbite (with around 39 wt% Ta2O5) in the most northerly dike, to more complex assemblages comprised of manganotantalite (with up to 75 wt% Ta2O5), ferrotapiolite (with up to 79 wt% Ta2O5), and microlite (with up to 76 wt% Ta2O5) that are present in dikes located several kilometers to the south and southwest. The compositional characteristics and textural relationships of the tantalum-bearing minerals in the dikes provide evidence of igneous fractionation trends that are typical of rare-element granitic pegmatites. Such trends suggest that the newly discovered pegmatites represent part of a more extensive group of cogenetic, tantalum-mineralized dikes.

Jan 1, 2001

By Arnold R. Pasieka, George V. Sotirow

"The object of this paper is to outline a computerized net cash flow approach for practical cutoff grade determinations. A cutoff grade carries not only geological but also economic value, in which costs are balanced against revenues. For different situations, cutoff grades are a 'standard of value' that are determined for the purpose of classifying economic or uneconomic mineral reserves in a specified time frame. In a constantly changing technical and economic environment, the decision to develop or maintain a mining operation at its best economic potential, requires an appropriate cutoff grade strategy, a strategy consistent with short- and long-term operational and corporate objectives and one based on realistic marketing and metal prices forecasts. The use of a project evaluation computer program, in combination with specific corporate net cash flow requirements, shows the most promising and flexible team approach for cutoff grade optimization.IntroductionThe recent recession has had a devastating effect on the Canadian mining industry. Exploration and mining R&D expenditures have been critically reduced and now are believed to be below healthy levels. Ore reserves, mine life and cutoff grades are careening in several directions because of low base metal prices, relatively high costs and sensitive precious metal prices.These conditions demand an improved understanding of the terms ""ore"" and ""cutoff grades"" as they are applied to the planning process and day-to-day operations. ""Ore"" or 'ore reserves"" is a dynamic concept, reflecting a cumulative effect of changes in geological, technical and economic conditions in terms of material which can be mined at a potential profit. By contrast, if economics are not the primary consideration, the term ""mineral reserve"" or ""mineral inventory"" should be used to describe the mineral deposit. For different situations, cutoff grade is ""a standard of value"" determined for the purpose of classifying mineral reserves as economic or uneconomic in a specified time frame. The question of mining at average reserve grade or low-grade material during high metal prices is of paramount importance for cutoff grade strategy."

Jan 1, 1985

By J. Ipinza, J. P. Ibáñez, Casas J., S. Cortés

Copper powder generated during the treatment of electro-metallurgical bleeds by reactive electro- dialysis (RED) had totally reduced the content of ferric ions in acidic synthetic electrolytes (Cu (II)- Fe (III) – H2SO4). In batch and columnar experiments 100% of the ferric ions were reduced to ferrous ions with an extremely high kinetics. A preliminary conceptual design for reducing ferric ions based on an integrate RED- Column for treatment of electro-winning bleed system is discussed. This system is able to recover simultaneously sulfuric acid and copper powder, which will reduce ferric ions. INTRODUCTION It is well known the negative effect of ferric ions in the copper electro-winning process. The increase of ferric content in the electrolyte reduces the current efficiency, i.e., there is an increase in the energy consumption, and changes the surface morphology of the copper deposit (Das, Gopala & Krishna, 1996; Vargas & Parra, 2013). The increase of the specific energy consumption due to the loss of current efficiency occurs by the reduction reaction of ferric to ferrous ions in the cathode, at the anode the ferrous ions are slowly oxidized to ferric ions (Shaw, Dreisinger, Lancaster, Richmond & Tomlinson, 2004). To control the level of iron in the electrolyte, bleeds are needed; this bleed electrolyte containing copper, sulfuric acid, cobalt, iron and other impurities normally is waster, which increased the production cost of the plant (Milbourne, 2002; Mckevitt & Dreisinger, 2009). Then, permanent efforts oriented to treat those bleeds to avoid losses of valuables components are made; among them are use ion exchange resins (Shaw et al., 2004; Mackevitt et al., 2009), chemical precipitation (Izadi, Mohebbi, Amiri & Izadi, 2017) and electrodialysis (Cortés, Ipinza & Ibáñez, 2013). The last one allows to the simultaneous recovery of sulfuric acid and copper powder. If one of the valuables obtained by treating the bleed can be used to reduce ferric ion concentration in the electrolyte could be an important asset. This issue at laboratory scale is reported in this work, the use of copper powder, generated by reactive electro-dialysis when treating synthetic acidic electro-metallurgical bleeds, for reducing ferric ions in acidic electrolytes.

Jan 1, 2019

By Phillip Mackey, Elmira Moosavi-Khoonsari

L'industrie du cuivre traverse une période passionnante, marquée par une forte demande, de bons prix et l'ouverture de nouvelles grandes installations. L'année 2022 a battu des records de production de cuivre, ce qui laisse entrevoir un potentiel de croissance supplémentaire. De grands projets sont en cours, comme la technologie Double Flash à Manyar, en Indonésie, qui peut produire plus de 500 000 tonnes de cuivre par an. À Munda, en Inde, on a construit la plus grande usine de cuivre du monde, qui produit plus de 1 000 000 tonnes de cuivre par an en combinant deux phases. De plus, l’installation de cellules de flottation de dernière génération au Mexique, au Chili et dans d'autres pays témoignent de la volonté de l'entreprise d'utiliser les technologies les plus récentes [1]. L'importance du cuivre dans la transition énergétique est évidente, l'accent étant mis à la fois sur la croissance et sur la protection de l'environnement. Cela se traduit par le développement d'usines de premier ordre dédiées aux pratiques durables.

May 2, 2024

By J. A. E. Bell

"Inco has shifted part of its traditional extractive research effort at its J..Roy Gordon Research Laboratory in Mississauga toward new, value-added products. Most of the effort is being expended on new Ni powders for batteries and new Ni-coated products which will be produced in Inco's carbonyl nickel refineries. New products under development are Ni-coated powders, Ni-coated fibres and ultra-fine Ni powders. Other new products for advanced material applications include controlled expansion composites, NiGOLD strip, Thermal barrier coatings on Inco alloys, and plasma coatings.Research and Corporate Strategic ThrustsThe newest strategic thru st of the company is to increase the value of the primary metal products. These new products are to be in addition to any new alloys or downstream alloy fabrication.Historically Inco has had the highest research expenditures in the extractive metallurgy field in North America. This has resulted in many new processes including flash smelting , matte separation, fluid bed roasting, pressure carbonyl refining and cobalt electrowinning which have contributed to establishing Inco as the lowest cost nickel producer. The recession of the 1980s caused a restructuring of Inco research and corporate goals .As shown in Figure I, from 1975-1982, i.e. pre-recession, Inco spent around 33 million dollars per year on research. Some 48070 of that sum was spent in Corporate Laboratories in Sterling Forest in the United States and in the United Kingdom , mostly on alloy associated research. A further 10% was spent on alloy research at the alloy production facilities in Hunting- ton, West Virginia, and Birmingham and Hereford in the United Kingdom. On extractive research, 13% was spent by process technology groups at the plant s, 20% at the pilot plants in Port Colborne and 9% at the J. Roy Gordon Research laboratory.The relative research expenditures (Fig. 2) have decreased so that today they are at the same level as 1975-80. The research as a per cent of sales has been cut from 2.2% to 1.2% of normalized sales. A normalized sale price of $4.00/lb Ni was used in the 1988 figures. This was partly achieved by closing Corporate Laboratories. Most of the essential alloy research was moved to producing plants and total alloy research is now 27%.A new thrust initiated in the 80s was mining research which now accounts for 20% of research expenditures. Over a period of the past five years this research has doubled the mining productivity in Inco. The pilot plant expenditures have been cut in half. One entire research station at Port Colborne was converted into a platinum group metals intermediate refinery. The decrease in pilot plant expenditures has been compensated by full scale plant trials devoted to the S02 abatement program at Sudbury."

Jan 1, 1990

By C. Zangerl, H. Lechner

"Large scale rock slides in deeply incised Alpine valleys are common hazards that can endanger human life, settlement areas and critical infrastructure such as highways, railways and reservoirs (Bonzanigo et al., 2007). In order to perform reliable forecasts of the behaviour of rock slides influenced by large dam reservoirs the geometry, the kinematics, the deformation behaviour and the hydrogeological situation need to be understood profoundly. Based on generic rock slide models the influence of the rock slide geometry on the stability as well as the impact of the buoyancy forces and water load of the reservoir at the toe of the slope are the main focus of this study. Various assumptions of hydraulic conductivity, groundwater conditions of the rock slide and impoundment depth of the reservoir are analysed using limit equilibrium approaches.Generally, deep seated rock slides are characterised by deformation along one or multiple shear zones where most of the measured total slope displacement localizes. Many large rock slides, especially those observed in foliated, mica-rich crystalline rock masses (e.g. paragneisses, mica schists, phyllites), do not fail suddenly or reach high velocities. Instead, many of them move slowly and reach velocities of centimetres per year or even less. Some show episodic accelerations, sometimes reaching alarming levels, but then subside to non-critical levels again. However, there is a potential that deep-seated rock slides fail rapidly, develop into far-reaching run-out rock flows, and cause catastrophic events. Whereas the role of triggers in promoting phases of acceleration is often understood, the same cannot be said regarding the kinematics and dynamic processes by which the rock slide mass decelerates, re-stabilises or accelerates to a catastrophic degree once the trigger impetus has been removed. Thus key questions of the presented work concern the geotechnical, geometrical and hydrogeological conditions under which a slowly moving rock slide is triggered to accelerate to irreversible, maybe dangerous velocities. The development of the sliding zone is generally influenced by pre-existing discontinuities such as brittle fault zones, shear and tensile fractures, foliation and bedding planes. These geological structures determine the geometry of the sliding zone which can either be rotational or translational. During the gravitationally induced failure process the geometry of the rock slide undergoes a change.Several observed post-failure geometries in metamorphic rocks show a concave topography in the middle to upper part of the rock slide and a typical convex or bulge-like topography at the toe of the slope (Zangerl et al., 2012). Whereas the sliding zone of the upper part of such a rock slide mass is rather steep and planar, the inclination of the sliding zone at the toe can be close to zero and act against the driving forces (Alonso et al., 2010). A shear zone that meets alluvial deposits at the foot of the slope encounters a stabilizing impact on the mechanical behaviour. This buttressing effect of alluvial sediments has a remarkable influence on the slope stability."

Jan 1, 2015

By P. R. A. Andrews

"Graphite is one of the most versatile of non-metallic minerals because of its diversified properties, for example: it is unctuous; it marks readily; burns slowly; is almost chemically inert; is flexible over a large temperature range; is a good conductor of heat and electricity; is hydrophobic; has a negative temperature coefficient of resistivity; has excellent weathering properties; tends to emulsify with water-in-oil; is readily soluble in iron; and after oxidative treatment, can exfoliate like vermiculite. These properties give rise to its major uses in lubrication, refractories, marking instruments, electrical products and paints.Flake graphite is the variety which commonly occurs in Canada; the provinces of Ontario and Quebec contain the deposits of economic significance, although graphite occurs in other provinces. The beneficiation of graphite has been the subject of many investigations at CANMET, thus reflecting graphite 's importance as an industrial mineral. Thirty-eight studies relating to various aspects of beneficiation were conducted between 1918and 1989anda review of some of the more important studies is presented. The information includes mineralogy, beneficiation methods and results; flotation parameters and reagent concentration data are presented in tabular form. By so arranging the principal data, the research worker and production metallurgist will be assisted in the evaluation of graphite ores from a variety of origins."

Jan 1, 1992