Search Documents

By E. L. Jones

THE concentration of tin in the tailing from Sullivan ore has been de-scribed by H. R. Banks, superintendent of the Sullivan concentrator, in a paper presented at the annual meeting of the B.C. Division of the Institute in October, 1941(1). The reduction of the concentrate EARLY EXPERIMENTAL WORK Experimental work on the smelting of Sullivan tin concentrate was done in Trail. Preliminary tests in the laboratory indicated that the concentrate could be successfully treated in an electric furnace. A small electro-thermic pilot plant was built and, at the same time, reduction tests were made in an oil-fired reverberatory furnace. Both types of treatment gave satisfactory results. It developed that no fluxes, other than those already in the ore and in the ash of the reducing agent (either coke or coal), were needed. By using an excess of iron, a complete recovery of the tin in the slag was obtained, but with 20 to 30 per cent iron in the tin. A counter-current treatment was thus indicated, viz., the primary slag was first treated with hard-head (iron-tin alloy) from the refining and final slag smelting, producing tin with 2 to 4 per cent Fe. This secondary slag was subsequently treated with scrap iron to produce tin-iron alloy, and a final slag low enough in tin to waste. By following this line of endeavour, a tentative flow-sheet was drawn up and a successful operation was established. Without resorting to electrolytic refining, a metal comparable in purity to standard tin was produced. Metallurgical results and operating costs were found to be very similar with an electric furnace or a fuel-fired furnace. 'However, electric furnace smelting was chosen because the furnace required was smaller, and because some doubt existed as to the cleaning of the final slag in the reverberatory furnace reduction.

Jan 1, 1944

By S. Ghafarnejad Parto, Å. Rasmuson, A. Fredriksson, M. Mohammadi, K. M. Forsberg, J. Martinez De La Cruz

The present study aims at recovering rare earth elements (REE) in conjunction with the production of fertilizers from an apatite concentrate. Apatite is one of the REE rich minerals ending up in the tailings pond when Luossarvaara-Kiirunavaara AB (LKAB) in Sweden processes Malmberget’s iron ore deposit. Leaching with nitric acid, hydrochloric acid, and sulphuric acid respectively have been studied. The nitric acid route was chosen for further investigations and the optimum acid concentration for leaching of the REE were determined. The leached REE are recovered by solvent extraction using di-(2-ethylhexyl) phosphoric acid (D2EHPA) and 2-ethylhexylphosphonic acid-mono-2-ethylhexyl ester (EHEHPA).

Jan 1, 2014

By Tom Shumka

All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it is every six months or every three years. The inspection frequency depends upon gear tooth condition, and the objective is to ensure operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection, or dye penetrant examinations rely heavily on interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combined Eddy Current Array (ECA) and Alternating Current Field Measurement (ACFM) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.

Jan 1, 2012

By M. Xiao Bo

In recent years, there has been a heightened interest in the hydrometallurgical processing of sulfide ores and concentrates (especially copper sulfide ores and concentrates) mostly in the USA and Chile. Currently, hydrometallurgical operations account for about 30% of the primary copper production. In the present research, the leaching phenomena of IOCG (iron-oxide hosted copper-gold) ores and concentrates were studied. The IOCG ore, which is characterized as having a predominant amount of magnetite with fine chalcopyrite, is currently the center of attention for new copper resources. Heap leaching of IOCG ore is desirable because of its low cost. However, the leaching characteristics of the ores and concentrates and the mechanisms of copper leaching require investigation. This study defines the factors, which affect the leaching operation, such as the ORP, pH and oxidizing agents. Based on these results, the optimal leaching conditions are provided for pilot column leaching test and ultimately, commercial operations.

Jan 1, 2007

By T. Miura, Y. Mori, H. Aoki

In a flash smelting furnace, easily combustible concentrate particles excessively oxidized and melt. The excessively oxidized molten particles then collide with less oxidized solid ones to create uniform oxidized molten particles. This collision phenomenon plays a very important role in achieving high smelting performance. The authors developed a mathematical model describing above combustion phenomena. This model incorporated fluid flow, heat and mass transfer, chemical reactions and collisions of concentrate particles. Both gas flow and particle motion were calculated using the Eulerian method. Copper concentrate was assumed to consist of chalcopyrite(CuFeS2). Considered in the concentrate reactions were the decomposition of CuFeS2, and the oxidation of the resulting sulfur(S) and pyrrhotite(FeS) to produce magnetite(Fe30 4) and sulfur dioxide(S02). Moreover a reaction due to concentrate particle collisions, in which Fe304 in the excessively oxidized molten particle reacts with FeS in the less oxidized particle, was also considered. The particle collisions were assumed to occur according to a collision probability rule obtained by computational experiments. Particle growth in diameter was described as a change in the volume fractions of particle phases. When applied to a commercial flash smelting furnace, this model reproduced the particle growth and component transfer as observed in the actual furnace.

Jan 1, 2007

By David Stone

North American Palladium is the owner/operator of the Lac des Iles mine located 115 km north of Thunder Bay, Ontario. The mine has produced an average of 65,000 ounces of palladium since 1994. Lac des Iles is currently undergoing the first phase of a major expansion that will increase ore production from 2,400 tons per day to 15,000 tons per day. A future expansion is being contemplated for 30,000 tons per day. The current expansion will increase palladium output to 250,000 ounces per year. The mine plan for the ultimate pit results in an excavation 1 km long by 800 m wide and over 450 m deep. This makes the ultimate pit at Lac des Iles one of the ten deepest open pits in the world, and the largest in Canada. This paper outlines the geotechnical data collection and design methodology for the ultimate open pit at Lac des Iles.

May 1, 2001

By M. Specht, D. Pörzgen, W. Lorenz, A. /. Buhr, R. P. Racher

The introduction of the near net-shape casting process at CORUS Staal IJmuiden in January 2000 required changes of secondary metallurgy processes including a development towards more aggressive slag compositions in the steel ladle. Therefore the steel ladle lining has been changed from fired andalusite bricks to magnesia-carbon bricks and, most recently, to fired spinel bricks to withstand the severe slag conditions. In comparison to the andalusite bricks the new steel ladle linings have a higher thermal conductivity. This requires the capability to keep the lining warm by ladle preheaters to sustain the overall thermal stability of the steel ladle in case of interruptions during hot cycling of the ladles.

Jan 1, 2004

By Masaru Kato

The plated gold being used by the electronics industry can be broadly classified into two categories: soft gold and hard gold. Soft gold is used for circuit metallization and for bonding semiconductor chips, while hard gold is indispensable as the contact material on electrical connectors, electromechanical relays, and printed circuit boards. The traditional baths from which to plate soft gold as well as hard gold contain the cyanide complex, [Au(CN)2]-, as the source of gold, which liberates free cyanide ions during the plating. The free cyanide is not only highly toxic but also attacks photoresists used to delineate circuit patterns and bonding pads. For these reasons, non-cyanide baths are in use to plate soft gold, whereas hard gold can be plated only from cyanide baths at present. In this presentation, the current status of both electrolytic and electroless non-cyanide processes for plating soft gold will be reviewed.

Oct 1, 2003

By R. G. Bradbury

The paper uses two hypothetical, but typical, situations to show that hydraulic rock drilling equipment has very significant economic advantages over pneumatic equipment both in drifting applications (even in the situation where advantage is not taken of the high productive capacity of the hydraulic drill) and production drilling applications. Other factors, including the non-economic advantages and the disadvantages of hydraulic drilling, are discussed. The paper concludes with a brief analysis of why the Canadian mining industry has been slow to take advantage of this apparent broadly advantageous advance in rock drilling technology.

Jan 1, 1979

By Tom Shumka

All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it is every six months or every three years. The inspection frequency depends upon gear tooth condition, and the objective is to ensure operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection, or dye penetrant examinations rely heavily on interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combined Eddy Current Array (ECA) and Alternating Current Field Measurement (ACFM) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.

Jan 1, 2012

By P. J. Adams

Environmental regulations require means for controlling emissions of SO2 NOx and particulate when burning coal. The combustion of coal in limestone fluidized beds is one of the most promising techniques for the necessary reduction in emissions. Fluidized-bed firing, furthermore, offers potential economies in capital equipment. The world's largest steam generator applying fluidized-bed techniques was built under the sponsorship of ERDA and installed in Rivesville, West Virginia. This paper describes the design and discusses the start-up and development difficulties which were experienced during the period from initial operation to current readiness for commercial operation. Other developments leading to utility and industrial fluidized-bed steam generating equipment are reviewed. The future potential of this promising technique is discussed.

Jan 1, 1979

By R. Pot

"IntroductionTHE PURPOSE of this paper is to discuss briefly the main logging and testing devices presently at our disposal, to point out some of their limitations, and to suggest possible improvements of the techniques.Some of the more important devices .are those that are used in:(1) Coring(2) Formation testing(3) Electric well logging(4) Radioactive well logging(5) Measuring of bottom hole pressures(6) Sampling of reservoir fluidsThe first four of these procedures are concerned with the well while it is in the process of drilling. The last two are carried out as soon as possible after a well has been brought into production and .at intervals during its life. My remarks will be concerned mostly with certain aspects of formation testing. The reservoir engineer is dependent on the information derived from these operations in order to obtain a clear picture of the conditions in a reservoir and to enable him to assess and forecast its future behaviour.Since any calculation is no better than the data on which it is based, not enough emphasis can be placed on the necessity for the testing and logging equipment to be of the highest quality and for the analysis of the results obtained to be thorough."

Jan 1, 1952

By Hooman Askari-Nasab

Open pit mine plans define the complex strategy of displacement of ore and waste over the mine life. The objective of the mine plan is to maximize the future cash flows within the technical and physical constraints. Various mixed integer linear programming (MILP) formulations have been used for production scheduling of open pit mines. In the MILP formulation the slope constraints guarantee that all the overlying blocks are mined prior to mining a given block. Traditionally, the slope constraints have been modeled with cone templates representing the required wall slopes of the open pit mine. The overall pit slopes constructed by these templates are a function of the width and height of the geological block model. Therefore, the overall slopes are fixed in one bearing. This paper presents a general MILP model for open pit mine scheduling with variable slopes constraints. The methodology utilizes a directed graph to capture the precedence of extraction of blocks and pit slopes in different bearings. Depth-first-search algorithm was used to traverse the graph for constructing the slope constraints in the MILP problem. TOMLAB/CPLEX was used as the implementation platform to efficiently integrate the mathematical solver package CPLEX with MATLAB. A case study on intermediate scheduling of an iron ore mine over twelve periods was carried out to validate the models.

Oct 1, 2009

By P. Henry

Hydrometal provides an adequate technology to reintroduce lost metal units into the industrial cycle, thereby saving resources and energy, while keeping the environment cleaner. Two case studies of our integrated hydrometallurgical recycling facility (Hydrométal) in Belgium are discussed.(I) Recycling of Cu-Co cement generated at the second purification step of zinc sulfate solution. (II) Recycling of lead complex materials from the lead industry.

Jan 1, 2008

By Patricia Dillon

EHS Management Standards Communication and Reporting (8) ! Establish processes for internal and external communications ! Designate responsibilities for communication with COI ! Report as defined by senior management ! Report annually to employees, shareholders, COI on EHS and social performance Community Rights and Public Consultation (9) !Identify COI?s and establish process to hear concerns !Acknowledge and respond to complaints !Support local communities !Plan for closure and conduct public consultation !New projects include identification of COI?s, concerns to be considered in design

May 1, 2004

By T. Crivits

"Phase equilibria in the ‘Cu2O’-‘Fe2O3’-SiO2 system, the base slag system in copper production, were recently determined. However, the addition of MgO, commonly present in the slag, drastically changes the phase equilibria in this system. The present study focuses on the phase equilibria in the ‘Cu2O’-‘Fe2O3’-MgO-SiO2 system in equilibrium with metallic copper.Recently, an experimental procedure has been developed that resolved a number of experimental difficulties. This procedure has been successfully applied to characterise several complex industrial copper slags. It includes a high-temperature equilibration followed by rapid quenching and electron probe X-ray micro-analysis (EPMA). The methodology was adapted to the present system and used to determine the liquidus at SiO2 saturation and in contact with high-MgO phases in between 1100 and 1250 °C in Cu2Orich slags.The results indicate a maximum solubility of MgO in the system at 1200 °C of 5 wt%. The boundary line between tridymite and spinel lies 3-4 wt% closer to the SiO2 apex for every 2 wt% MgO added. These new data on the high-copper slags are important for optimisation of the direct-to blister"

Jan 1, 2014

By Brian Lewis

"IntroductionThe leaching method selected for the dissolving of uranium ore depends in part on the physical characteristics of the ore, as well as the uranium mineralization. There are two main methods of leaching employed in uranium circuits in North America, one being ""Carbonate Leaching"" on sandstone, and pitchblende type ores, and ""Acid Leaching"", on quartzite type ores.This chapter deals with the acid leaching of uranium ores found in the Elliot Lake area, using sulphuric acid, for the leaching reagent, and ""pachucas"" for the contactor.The basic leaching process involves the pregrinding of the ore and the mixing of the ore with hot sulphuric acid, the mixture is air agitated, the air being used to oxidize the ore as well as produce agitation. The chemical reaction is as follows: Uranium Oxide + Sulphuric Acid = Uranyl SulphateThe following equations show the actual dissolution of the ""Hexavalent Uranium"", which show that more than one ion or complex of uranium is possible.Uranium DissolutionsI. UO, + 2H-(UOJ + H,O2. (UO,) + SO, = -UO, SO, (Uranyl Sulphate)3. UO, + SO,-(UO, (SO,),)=4. (UO, (SO,),)= -(UO, (SO,),)'Test work carried out in the laboratory as well as in the plants has determined the most efficient methods of extracting the uranium from the ore. A very important factor that has to be determined during initial test work are the amount of acid consumers in the ore. Within the Elliot Lake orebodies are minerals such as chlorite schist, diabase, and basement material, all very high acid consumers, consuming up to 1000 lbs. of acid per ton of ore. Of these minerals only the chlorite schist contain any uranium at all.The following are the operating parameters that have to be controlled in the plant:I. sulphuric acid concentration2. temperature of the mixture3. agitation4. liquid solid ratio5. reaction time6. particle size of ground ore"

Jan 1, 1989

By J. G. Conaway, P. G. Killeen

"Gamma-ray spectral logging, a useful technique for uranium exploration and evaluation, has generally been underutilized by the Canadian mining industry. Provided that the technique is properly applied, it is capable of yielding reliable quantitative information regarding the distribution of uranium and other radioelements along the borehole under most conditions.In practice. there are numerous factors which potentially can degrade the quality of the log and thus any quantitative interpretation based on it. Fortunately, the appropriate choice of logging equipment and technique can avoid many such problems, and corrections can be applied to the data to compensate for most of the others."

Jan 1, 1980

By J. A. Finch

Samples of feed and product from a closed grinding circuit treating a heterogeneous lead-zinc ore were taken. The feed was subjected to laboratory batch grinding in a rod and ball mill with the objective of simulating the closed-circuit size distribution. It was concluded that the batch rod mill can closely simulate this product if only the over-all size is considered, but mineral-by-mineral large differences occur. If, as is suspected, the mineral sizes are the important factor in flotation, the differences could lead to problems in interpreting flotation results. An example of mineral recovery as a function of size is described to illustrate the potential problems.

Jan 1, 1979

By Marcel Vallée

Abstract -Traditionally, samples collected for mineral deposit evaluation have been viewed without explicit reference to reliability, with the illusion that a true value is attainable from a few samples and verifications. For exploration, mineral deposit estimation and production quality control the following definition is proposed: "a sample is a small quantity of material relative to the geological mass it represents, collected according to a systematic procedure, of measurable reliability, from which the grade/quality of the mass which it represents may be estimated, based upon appropriate protocols. This paper will concentrate on the actual rock sampling process. Too often, sample size has been, and is still viewed as a matter of convenience, leaving out representivity considerations, despite the importance of samples on project estimation. Linear samples (chips, channels, drill), panel samples, broken rock or mining samples and very large samples are considered. Collection procedures and quality control protocols to improve the representivity of non-mechanical samples are proposed.

Jan 1, 1998