Search Documents

By Makhlouf Boubahziz

The HNIA field is part of the Tinrhert project which consists of developing 17 fields containing essentially gas with a few small rings of oil. It is considered as one of the main fields in this project in terms of its area and the number of geological structures that has formed it. It is a wide anticline of Cambro-Ordovician age, orientated NNE-SSW and located in the South-eastern part of Illizi basin. This structure extends from Alrar-center in the North, to the North of In Amenas in the South. The area is 1350 km2. The main reservoirs forming HNIA field are the Devonian (F2, F3 and F4), Siluro-Devonian (F6) and Cambro-Ordovician. These latest are formed by 4 sandy units alternated by layers of shale and shaly silt termed from the base to the top as follow: Unit II, Unit III-3U, Unit IV-2L and Unit IV3; these units are the subject of this study. The HNIA field is essentially gas, up to day this field is at the stage of appraisal and evaluation in order to establish a development plan; therefore the main target of this study is to contribute to this frame work. The following objectives are: ?To build a structural model of the study area. ?To integrate all the sedimentological, structural and petrophysical data in order to build a 3D geological model

Aug 1, 2013

By R. Chen, K. Xia

In deep mining activities, blasting induced compressive stress wave would be reflected as tensile wave at a free surface around the openings, which would facilitate the tensile failure of the deep rock since it is much weaker in tension than in compression. It is thus critical to understand the dynamic tensile failure of rocks subjected to static tension for deep rock engineering applications. A modified split Hopkinson pressure bar (SHPB) system is adopted to load Brazilian disc (BD) samples statically, and then exert dynamic load to the sample through stress wave generated by impact. The pulse shaper technique is used to generate a slowly rising stress wave and thus to facilitate the stress equilibrium of samples during each test. Five groups of Laurentian granite (with tensile strength of 12.8 MPa) BD samples under the pretension stress of 0 MPa, 2 MPa, 4 MPa, 8 MPa, and 10 MPa are tested under different loading rates. The result shows that the dynamic tensile strength of the rock decreases with the increase of pre-tension stress, which is easy to understand because pre-tension stress weakens the rock sample. It is also observed that under the same pre-tension stress, the dynamic tensile strength increases with the loading rate, revealing the so-called rate dependency that is common for engineering materials. Furthermore, it is found that the loading rate sensitivity of the rock increases with the increase of pre-tension stress. A qualitative explanation for this phenomenon is that more microcracks are generated and activated under higher pretension stress, resulting in a more viscous material. Based on the results, an empirical equation is proposed to fit the data and explain the dynamic tensile behaviour of rock under pre-tension stress. A physical model is used to simulate the dependency of the dynamic tensile strength of rock on the pre-tension stress and the loading rate, which is shown to be in good agreement with the experimental results.

Jan 1, 2015

By K. D. A. Whaley

Abstract -The Captain North Extension deposit consists of five sulfide lenses hosted in cherty and chloritic metasediment that is bounded by quartz-eye rhyolite and laminated rhyolite . Lens 2 consists of sphalerite and galena with silver-rich tetrahedrite in chert. Lens 3 contains massive pyrite, with chalcopyrite and minor gold, gradational to minor pyrite in a chloritic metasediment . The other lenses are unexplored. The sulfides occur as beds, fracture infills, and disseminated grains. Reserves are estimated at 207 555 tonnes grading 7.38% Zn, 2.76% Pb, and 91.81 g/t Ag. The deposit is isoclinally folded, dips steeply west, plunges 50 degrees south, and is faulted out to the north, where drag folding has reversed the plunge. Minor cross-faults contain talc and sericite. High sphalerite but low pyrite abundances result in poor responses to standard electromagnetic techniques. Lens 3, which contains more pyrite than Lens 2, responds better to induced polarization and allows detection. Geochemical anomalies are found in a nearby swamp and stream, but an impervious till cover inhibits the development of soil anomalies.

Jan 1, 1992

By K. Sakai, M. Miyaue, T. Aoki, T. Tani, S. Tanaka, N. Kudo

In the planning stage of a tunnel, due to limited technology in the geological survey and the financial restriction, tunnel supports are often designed from unsatisfactory information, and the tunnel construction is started. Therefore, "Information-oriented construction" is carried out in the construction stage, in which the design is rationally verified and modified by observations/measurements. Moreover, the ground conditions ahead of a tunnel face must be predicted for efficient and safe tunnel construction. The authors have examined effective prediction methods to the ground conditions ahead of a tunnel face under construction of mountain tunnels (Aoki et al., 2010) in view of the established method (Schubert et al., 1995). Though the prediction method of Schubert requires the displacement in the direction of tunnel axis, it is difficult to obtain its accurate data by the electronic distance meter. Then, we have proposed a method that uses tilt sensors installed at the tunnel crown near the face to obtain the slight tilting information. To measure inclination of the tunnel crown, this inclinometer was originally developed as a daily control measurement, such that the geological condition and its possible change behind the face could be detected early, and a steady advance and construction safety could be ensured. This paper describes the method of forward prediction mechanism and advantages of this suggested method. It then presents the typical results of a field verification test at a tunnel under construction and an example of evaluation of the ground conditions ahead of the face based on the 3D numerical analysis in three types of condition changes of ground deformation moduli.

Jan 1, 2015

By P. A. Mascaró, N. Chacon, A. A. Cecchi

"This document shows the development of a system called the “On-line charge level determination in SAG mills” (abbreviated as Jc). The Jc variable has certainly been difficult to measure due to the relevant number of factors and variables that affect the grinding phenomena inside semi autogenous (SAG) mills. To assess the feasibility stage of the proposed system, it was necessary to carry out two tests in different sized SAG mills, 38´ × 22´ and 36´ × 15´, respectively. In each test, the system was configured with a battery of sensors of the following types: (1) strain gauge, (2) accelerometer, and (3) gyroscope. The first step involved for charge level determinations was to determine kidney foot and shoulder by means of a study of the energy-impacts on shell structures. The second step consisted of correlating the measured grinding operational variables with the actual charge levels obtained from SAG mill crash stops. This system development is extremely useful and relevant for providing approximations about mass balances inside SAG mills. It will be a suitable tool for explaining “tonnes per hour” variations and determining optimal points under various operating conditions.INTRODUCTIONThere has been a growing necessity for technologies capable of obtaining “on-line data” of the main comminution variables in order to increase throughput. Computer systems have taken an important role in providing important solutions by means of processing on-line device signals (commonly referred to as monitoring). In semi autogenous (SAG) milling, there are many examples of monitoring devices that allow the operational staff to obtain detailed information both mechanically and electronically inside a grinding circuit. In this context, a new technology has been developed to obtain “Jc total charge (%) online” in two different SAG mills called Vibro-Energy® System.As part of the analysis performed by JKsimMet® the Jb/Jc was estimated because it has an important impact on SAG mill throughput. Different scenarios were simulated and contrasted at various theoretical Jb/Jc values in a baseline circuit (Figure 1)."

Jan 1, 2016

By E. Demedde

Carbon anodes in aluminium reduction cells are continuously consumed during electrolysis. In prebake cells the anodes are replaced at regular intervals. The spent anodes, called butts, are often allowed to cool in air while emitting fluorides into the building from the hot alumina cover and the adhering bath. In modem smelters spent anodes are placed inside enclosures and fluoride emissions during cooling are effectively reduced. Fluoride emissions from spent anodes were estimated by considering the kinetics of fluoride formation, a heat transfer analysis of the cooling anode butt and the ventilation flow from a cavity. Fluoride emissions from large anode butts cooling inside enclosures were compared with those cooling in air. Good agreement with published experimental values was obtained for enclosures having different leakage opemngs, when a hydrofluorination reaction of the spent anodes was included.

Jan 1, 2006

By J. H. Hodgson

"Those of us who have been concerned with the problem of geophysical exploration in southwestern Ontario have followed the development of the Poulter method with much interest. I have much appreciated the opportunity of reading an advance copy of Dr. Poulter's clear exposition and of preparing the following brief remarks on the probable applicability of the method to the Palaeozoic area of southwestern Ontario.During the years 1944 to 1946, the Ontario Department of Mines, in co-operation with the Union Gas Company and the Dominion Natural Gas Company, operated an experimental party in the hope of establishing a seismic technique appropriate to the •area. The results were completely negative. During two summers' field work, no reflections whatever were obtained except in one area near Windsor. It is the •purpose of these remarks to inquire whether Dr. Poulter's techniques might yield favourable results.It was the conclusion of the report on our work that two principal causes contributed to the failure of the method. In the first place, the geological column possesses few elastic discontinuities and those that exist appear to have low reflection coefficients. In the second place, the area is drift-covered in general. This drift complicates the situation by absorbing seismic energy and by giving rise to groups of complicating refracted phases which obscure the entire interesting section of the record. The situation is further complicated by the high reflection velocities and the relative shortness of the Palaeozoic section, these factors combining to bring in a reflection from the basement in about half a second."

Jan 1, 1950

Mining companies around the globe have long struggled with the need to ensure that earth moving equipment is designed to be operated and maintained under all site conditions without causing harm to people. Incident and accident data from a range of sources clearly identify mining equipment related issues as major causal factors. One Australian source, the NSW Department of Primary Industries? International Mining Fatality Database Project Report (2008) noted that ?Approximately 77% of mining accidents resulting in a fatality have? involved equipment?. The largest number of fatalities were associated with trucks; the next with LHDs. Many of the technical advances in equipment design over the past few decades have not been matched by advances in the human factors design of mining equipment, resulting in a ?design vacuum? that must be filled prior to commissioning new equipment. This ?design vacuum? is generally filled by local dealers. They retrofit equipment according to customer requirements to mitigate risks that have not been designed out by the Original Equipment Manufacturer (OEM). Mining companies have been frustrated by lost time and additional costs associated with this need to retrofit ex-factory designs. Some companies have attempted to address the problem by negotiating company or site-wide ?solutions? to equipment designs, but this has not simplified or clarified the issue from the point of view of the equipment manufacturers. A number of mining companies operating in Australia first discussed the concept of a joint customer approach to improve the Human Factors design of earth moving equipment at the factory level in 2004. They agreed that a new approach to engaging with OEMs was needed; one that would define the ?Problem?, in other words, the basis of the risks, rather than dictate the ?Solution?. The Earth Moving Equipment Safety Round Table (EMESRT) was formally established in 2006 by six global mining companies to establish a process of engagement between Original Equipment Manufacturers (OEMs) and mining customers.

May 1, 2009

By T. Alan O'Hara

"The decision to invest capital in developing a mine and constructing a mineral processing plant and services is usually made after a feasibility study shows 'that the estimated future cash flow from mine operations will yield an adequate return on the estimated capital expenditures.The actual return on investment may differ substantially from that estimated in the feasibility study, because of the probabilities of errors in estimating capital costs, ore reserves, operating costs, mineral revenue and operating productivity. This paper outlines the R.S.S. (root sum of squares) risk analysis procedure of computing the overall probability of the actual project D.C.F. (rate of discounted cash flow), differing from that estimated in the feasibility study.Variation in Project D.C.F.It is assumed that a feasibility study of the project has been completed which has defined the estimated values for all the project parameters, such as ore reserve tons and grade, capital cost, concentrate recovery, metal revenue, daily milling capacity and operating costs.The financial analysis of the mining project will have determined that the cumulative cash flow will yield an expected D.C.F. on the capital cost if all project parameters attain the estimated values. If, however, the actual value of any parameter varies from that estimated, the actual project D.C.F. will vary from the estimated D.C.F. Risk analysis methods attempt to determine the overall effect of probable variations in the estimated values of all project parameters on the D.C.F. of the mining project. This overall effect is expressed as a probability profile, which shows the likelihood of actual D.C.F. values greater or less than that estimated.Thus, a completed risk analysis of a mine project, with an expected D.C.F. of 15.51%, would display the characteristics shown in the preceding diagram."

Jan 1, 1982

By A. Zangooi, J. A. Finch

"A frother analysis technique based on the formation of a colored solution with UV-VIS absorbance proportional to frother concentration over a certain range has been developed. The calculation of concentration requires the comparison of the sample absorbance at a selected wavelength with a linear calibration (frother concentration vs. absorbance) constructed with values collected from solutions of known concentration (standards) at the same wavelength. It has been found that concentration ranges for preparation of standards can vary widely. An integration of our experiences into a databank can offer some guidance on the selection of standard concentrations. The databank includes results from the analysis of 37 chemical reagents, commercial frothers, and natural oils used in research work or at industrial sites. Grouping frothers by similar chemical structure or origin provides a good basis for selecting the standards to approach the maximum absorbance range for the spectrophotometer in use.INTRODUCTIONA technique to determine frother concentration on samples of industrial milling streams based on formation of a colored solution with UV-VIS absorbance proportional to frother concentration has been developed. The concentration is determined by comparison of its absorbance, at some selected wavelength, with those obtained by processing a series of solutions of known concentration (standards), at the same wavelength. It is desirable to have linear calibration (frother concentration vs. absorbance) over the widest concentration range. The upper concentration can be restricted by the instrument, as there is a maximum detectable absorbance (minimum transmittance), which can be reliably sensed by the UV-VIS detector (in most cases maximum absorbance is 3)."

Jan 1, 2016

By Adrianus (Adrian) Halim, Tomas Bolsöy, Stina Klemo

"This paper describes the ventilation system used in underground hard rock mines in Sweden and Finland, which is very different than the system used in other major mining countries such as Australia, Canada, South Africa, and USA. The system utilizes auxiliary fans with Variable Speed Drive to distribute primary airflow to working levels instead of regulators that are commonly used in other countries. Descriptions about Ventilation on Demand in this system and ventilation regulations in Sweden and Finland are presented in this paper. This paper also quantifies a comparison between the Nordic and the system used in other countries. KEYWORDS Auxiliary fan, Regulation, Ventilation on demand (VOD), Variable speed drive (VSD) INTRODUCTION The primary objective of an underground mine ventilation system is to provide sufficient airflow to dilute atmospheric contaminants that are produced by mining activities. Typically, a mine ventilation system consists of one to four primary fans, regulators to control primary airflow distribution to levels or panels, and auxiliary fans that distribute airflow to dead-end workings via ducts. Depending on circuit geometry, underground booster fans are sometimes used. This system is widely employed in many countries such as Australia, Canada, USA, United Kingdom, and South Africa. However, mines in Nordic countries such as in Sweden and Finland employ a different system, in which auxiliary fans instead of regulators are used to control primary airflow distribution, as well as distributing airflow to dead-end workings. This paper describes the general layout of Nordic ventilation system, its VOD and heating system, its comparison with the system that is widely used in other countries which is referred as “Non-Nordic ventilation system” in this paper, and the current ventilation regulations in Sweden and Finland. The comparison was quantified by doing simulations using Ventsim Design 5 software. DESCRIPTION OF NORDIC VENTILATION SYSTEM General System Layout Figure 1 shows a schematic of typical ventilation system used in Swedish and Finnish mines. The schematic was drawn by Franzen, Myran, Larsson, and Rustan from Stiftelsen bergteknik forskning (Swedish Rock Engineering Research Foundation) and the English translation is written next to the Swedish terminologies. The system is generally a push-pull system. None of Swedish and Finnish mines use exhaust system. As shown in Figure 1, the primary airflow is distributed to levels by auxiliary fans that are bolted to a bulkhead located in the access to intake raise/shaft. These intake fans are attached to ventilation ducts that distribute airflow to all working faces. The exhaust auxiliary fans, which are not attached to any ducts and also are bolted to a bulkhead located in the access to exhaust raise/shaft, then flow the exhaust airflow into the exhaust shaft. A small quantity of this exhaust air is directed into the ramp, which acts as another main exhaust airway. The deepest level is also equipped with booster fan(s) that draw air from the intake shaft/raise and direct it into the ramp to provide fresh air in the ramp. There is no free split in this system. Figure 2 shows a schematic of a level ventilation layout in the Nordic system. Figure 3 shows a photo of these auxiliary fans."

Jan 1, 2019

By J F. Davies

A review is presented of the fundamental differences between the Superior and Churchill geologic provinces. Structure, lithology, grade of metamorphism and a single recent age determination suggest that the Flin Flon -Snow Lake and Lynn Lake belts are remnant blocks of originally Superior rocks lying within the Churchill province. Major mineral belts occur along the main boundary between the Superior and Churchill provinces (the Thompson -Moak Lake nickel belt) and within the remnant Superior blocks inside the Churchill province (Fiin Flon -Snow Lake and Lynn Lake). During the Hudsonian orogeny, metamorphic gradients must have existed across the Churchill-Superior boundary and between the remnants of Superior rocks and the enclosing gneisses of the Churchill province. It is possible that not only the unusual nickel deposits of the Thompson belt but also the base metal deposits of the Flin Flon -Snow Lake and Lynn Lake districts are due to redistribution, or diffusion and migration of metals to areas of lower-grade metamorphism during the Hudsonian orogeny.

Jan 1, 1964

By Mary Kama, Kaul Gena

"Magnetic skarn ore (MSO) is one of the major copper bearing ore extracted by the Ok Tedi Copper Mine in Papua New Guinea. Copper minerals are recovered by flotation while the iron not associated with copper are discarded as tailings. The objective of this investigation was to determine the iron ore reduction kinetics for the Ok Tedi MSO and ascertain if it can be processed to produce sponge iron for a mini steel plant in Papua New Guinea.SEM-EDAX analyses of the Ok Tedi MSO indicated 10.1% C, 30% O, 0.6% Mg, 1.1% Si, 21.1% S, 0.8% Ca and 36.2% Fe. Most of the iron is in sulfide form. Both naturally occurring and roasted sinters of Ok Tedi MSO samples of different particle sizes were reduced by charcoal carbon at three different temperatures and seven different reduction times. Analyses of the reduced products indicated a metallic iron content of more than 65 wt.% on average.Results showed that there was no significant difference in reduction between fluxed and control materials. Only a slight increase in kinetics with reduced particle size, hence the reaction rate constant (K) did not vary much within the temperatures investigated. Reaction kinetics increases with increasing reduction time at 900°C. Therefore, more iron reduction is observed with particles of 106 µm size. In addition, the results also confirmed that the reduction energy used was higher at 800°C and lower at 1,000°C. In summary, iron reduction can be improved but close monitoring of temperature and reduction times are essential to determine the reaction kinetics of the Ok Tedi MSO. INTRODUCTIONMost mines in Papua New Guinea mine large quantities of iron in the form of sulfides, carbonates, oxides and sulfates that are eventually disposed off as tailings. The Ok Tedi magnetic skarn ore (MSO) contains a significant amount of hematite, magnetite, siderite, ilmenite and pyrite that can be a source of iron. The mineralogical compositions of Ok Tedi MSO reveals more iron minerals than copper, yet all iron containing minerals are collected in the tails from the main copper production stream. Therefore, this study is conducted to investigate the possibility of producing direct reduced iron (DRI), or sponge iron, from the MSO. Such sponge iron may serve as the feedstock for electric arc/induction furnace based mini steel plants in Papua New Guinea."

Jan 1, 2016

By Makarinskym F. M.

"This paper describes mechanical and operating modifications that were and are being made to current on-line flotation cells at Falconbridge Nickel Mines concentrators. Improved metallurgical performance and metal recoveries of some 3·4% over the past ten years are the end result of the modifications made. The paper acknowledges the contribution of operating, technical and maintenance personnel and the Company ""suggestion plan"" program. 1. INTRODUCTIONFalconbrirdge Nickel Mines Limited, incorporated in 1928 is a major product of nickel, copper,coba1t and other metals and minerals. The Canadian Nickel Division operating facilities in the Sudbury Area currently includes seven mines, two concentrators, and a smelter.For many years at all concentrators, improv0mcnts in metal recoveries have been continually under investigation. One area was to improve the flotation cell performance. This paper will deal with mechanical and operating modifications to the cells at the Strathcona and Falconhridge Ni-Cu sulphide concentrators, at the Sudbury Operations.One of the prime means to mineral beneficiation processing has been, and will continue to be, the basic froth flotation cell. The efficient operation of a flotation cell is the key to satisfactory metal selectivity and recovery. The essence of good design is simplicity. Changes to cell design can contribute to a significant improvement in metal recovery.Over the past 10 years, modifications to the flotation cells have contributed to an improvement of some 3-4” in mineral recovery. Providi11g tl1c initiative for improvements include operating, maintenance and technical personnel, as well as the employee suggestions submitted th1·ough the Suggestion Plan Program."

Jan 1, 1982

By S. Amira

In the last two decades, many new creep-resistant magnesium alloys have been developed for high temperatures applications. Their mechanical performance and corrosion behaviour were reported for various experimental conditions. However, these conditions often led to uneven comparison basis. In the present study the microstructure, mechanical properties and corrosion performance of four of these newly developed creep-resistant magnesium alloys were systematically compared. Specimens were obtained from experimental box-like components that were die-cast and thixocast in comparable conditions. Their mechanical and corrosion properties were compared using similar testing conditions. Results show that the creep resistance, strength and impact resistance of specimens are comparable but systematically lower compared to specimens cast under optimized conditions. The reduced concentration of elements such as Al, Ca, Sr and Ce lead to a decrease of the corrosion resistance of the magnesium alloys in 3.5% NaCI solution.

Jan 1, 2007

By Kenta Suzuki, Toshiya Anami, Daisuke Shimosaka

"In an Al-Mn alloy heat exchanger fin stock, the effect of annealing conditions for as-cast and 0.1%Zr addition on recrystallization behavior is investigated using metallurgical analysis. Refinement of post-brazed recrystallized grains in fin stocks with Zr addition are suppressed for long-time annealing. In 0.1%Zr fin stocks, there was a decrease in the number of fine a-Al(Mn,Fe)Si dispersoids for pinning of sub grain and grain boundary. In addition, relatively homogeneous distribution of Al3Zr dispersoids was observed with increasing annealing time in as-cast. Homogeneous distribution of Al3Zr dispersoids can have a major effect on pinning of sub grain and grain boundary during brazing heat treatment. The homogenous distribution of fine dispersoids prior to brazing heat treatment is effective in causing the suppression of refinement of post-brazed recrystallized grain structure in aluminum alloy fin stocks.INTRODUCTIONAl-Mn based alloys are widely used as fin stocks in automotive heat exchangers because of their superior mechanical properties, braze ability, sagging and so on. In particular, coarsening of recrystallized grain structure is beneficial to avoid erosion, and achieve excellent sagging resistance (Lee, Yoon, Kim & Jung, 2002). For resisting grain coarsening, the alloys should contain a dense and homogeneous distribution of fine dispersoids to retarder crystallization (Humphyreys& Hatherly, 2004). It has been demonstrated that addition of Zr to Al-Mn alloys can shift recrystallization to higher temperatures because of the distribution of fine Al3Zr dispersoids in matrix(Pokoba, Cieslar& Lacaze,2012). According to Tohma, Asanoand Takeuchi (1987), coarsely recrystallized grain structure was obtained in 3003alloy with Zr addition after heat treatment. However, fine Al3Zr dispersoids are usually heterogeneously distributed because of segregation during casting and low diffusion rate of Zr in aluminum. Therefore, a homogeneous distribution of Al3Zr dispersoids can be achieved through long-time precipitation annealing(Jia, Hu, Forbord& Solberg, 2008)."

Jan 1, 2018

By P. A. Christopher, R. H. Pinsent

"The Adanac molybdenum porphyry deposit near Atlin, in northwestern British Columbia, was discovered in 1905. It was explored extensively between 1967 and 1980.The deposit is within a complex, multi-phase, quartz monzonite stock that is a satellite of the post-accretionary, Surprise Lake Batholith. Biotite K-Ar dates range from 703 ± 2.4 Ma to 71.6 ± 2.1 Ma, indicating a Late Cretaceous age of emplacement.The deposit comprises an irregular-shaped ring or halo peripheral to a quartz monzonite porphyry dome, or ""cupola': The shape of the ring, and of a smal~ fine-grained quartz monzonite intrusion, and the presence of higher-grade mineralimtion on the eastern flank of the cupola, suggest partial control by a preminera/ structure. The deposit is truncated by a steep, northwesterly dipping, normal fault (Adera Fault) that down-dropped the northern half of the deposit by a minimum of 100 mThe deposit lacks strong zonal alteration but there are narrow envelopes of potassic alteration around some veins and local zones of intense wall-rock silicification. There is considerable retrograde alteration along postminera/ faults and fractures.Molybdenite occurs in veins and fractures, many of which are relatively flat-lying. They occur in all phases of quartz monzonite. Molybdenum is the only element of economic significance. There are vein and skarn occurrences with tungsten, tin, lead, zinc and precious metals peripheral to the deposit.In 1981, Placer Development Limited reported an ""undiluted mineable mineral reserve"" of 151 971 000 tonnes grading 0.063% Mo at a cutoff grade of 0.04% Mo and a strip ratio of 1.5:1."

Jan 1, 1995

By W. A. Jones

THE Ross mine, a subsidiary operation of Hollinger Consolidated Gold Mines, Limited, is situated near the north end of lot 1, concession 2, Hislop township, Ontario. The property comprises the north half of lot 1, concession 2, and the south one-third of lot 1, concession 3. It is readily reached by a good motor road from the village of Ramore, 7.5 miles to the southeast on the Temiskaming and Northern Ontario railway. The-mine has been developed to a depth of 900 feet and the current daily production rate is about 260 tons. From the inception of operations in March, 1935, until December 31st, 1942, 455,720 tons of ore with a total value of $4,169,-316 have been milled. The silver to gold ratio of 1.48 to 1 is unusually high for Ontario gold mines. The deposit is interesting because the relationship between hydrothermal metamorphism and three successive stages of fracturing and mineralization is marked with considerable clarity. During the past seven years, detailed geological maps of the mine have been kept up to date, many thousands of feet of diamond-drill core have been logged, and numerous thin and polished ore sections have been studied. The present paper describes the structure and mineralogy of the orebodies.

Jan 1, 1944

By Stephen G. Hardcastle

Worldwide, metal mines are going deeper. For example in Canada there are six such mechanized mines planning production at 3000m (10,000?). Working at such depths challenges all aspects of mining including the provision of ventilation to supply an equitable working climate for personnel and machinery. This paper explores the overall challenges of supplying ventilation in Canada?s deepest mines and how the volumes required could be minimized. This is essential because it must be remembered that ventilation and refrigeration are not only costly items to supply, but the magnitude of their cost is also very sensitive to the volume supplied. For ventilation this is obvious because of the cubic relationship between volume and cost. In deep mines, the main function of ventilation is the removal of heat transferred from the strata and generated by the mining machinery, and the air volumes supplied are designed accordingly. The second consideration is the removal of other pollutants that could be harmful to humans such as diesel and explosive fumes. However, the need for ventilation at its present design levels could be reduced. This paper discusses the implications of such technologies as: teleremote mining and alternatives to diesel equipment on the magnitude of the volume supplied; ventilation-on-demand which recognizes ventilation as a costly and limited resource; plus other aspects, such as the benefits of controlled recirculation, local cooling, and heat rejection back to the strata to gain further advantage from new developments. Furthermore, this paper advances the need to be able to design ventilation systems more cost effectively and how such new advances as process simulators can be used in conjunction with ventilation simulators to explore the diverse options that could affect the air volumes required and provide more realistic economic data upon which to base design decisions.

May 1, 2003

By Anton Sizo, Alexey Klyashtorin

The Gunnar uranium mine operated from 1953 to 1961 on the shore of Lake Athabasca, in 1964 the site was abandoned, and the mine pit flooded. In 1981, the pit was found to be stratified with a chemocline at ~70 m by a sharp change in conductivity and TDS. The uranium concentration was ~700 μg/l on the surface, 320 μg/l at 50 m, and 2,900 μg/l at 110 m. The Ra-226 concentrations were 0.1, 0.06, 0.12, and 0.4 Bq/l. By 2017, the chemocline was ~60 m deep. The highest uranium concentration was 1150 μg/l and the lowest concentration (220 μg/l) was attributed to the chemocline. In the deeper column, the uranium content varied around 750 μg/l. The uranium distribution down the pit profile was aligned with DO, ORP, and TDS. Ra-226 averaged to ~0.4 Bq/l, Ra-226 and uranium profiles were inversely related with the respective maximum and minimum attributed to the chemocline. The uranium and radium amount accumulated in the pit by 2017 was 3,420 kg and 2,163 GBq, respectively. The uranium and radium apparent accumulation trend estimates to 64 kg/y and 41 MBq/y, respectively. A stable chemocline and no concentration gradients in the other parts of the pit suggest that the contaminants are unlikely to inflow from the bottom opening or outside the pit, but rather are mobilized from the pit walls. The contaminants are not in a steady state, and concentrations of both uranium and radium are likely to increase slowly in the future if no remediation occurs.

Jan 1, 2020