Search Documents

By Bill Paparis

The thirty year old wharf structures at the Port Authority of New York & New Jersey?s Port Elizabeth Marine Terminal are being modernized for the next generation of Post-Panamax container ships, which require deeper water and larger container cranes. The terminal operator is upgrading the wharf in order to remain competitive, now and into the future. The upgrade coincides with the Army Corps of Engineers? $733 million project to deepen the main shipping channel in New York Harbor. This paper focuses on the structural modifications to accommodate berth deepening and to support the heavier loads of the new cranes. An overview is provided of the design and actual construction, including typical problems encountered when combining new and existing structures. The wharf improvements included: ? Installation of a steel king pile/sheet pile cutoff wall along the face of the wharf to permit increasing the depth from ?12.2 m + 0.61 m to ?15.2 m + 0.61 m ( ?40 ft + 2 ft to ?50 ft + 2 ft) ? Removal of the existing crane rail support beams and installation of new piles and beams to support the increased crane loads ? Replacement of the existing timber fender system with a new system capable of resisting the berthing energy of a 152,000 MT displacement vessel, and having dedicated sections for berthing barges ? Replacing the existing overhead, landside crane electric feeder system with a waterside, cable reel trench system. The work included upgrading the transformer capacity at the terminal for increased crane power demands This paper provides a case history for port administrators, terminal operators, engineers, and shipping lines challenged with upgrading aging terminals.

Jan 1, 2013

By Thomas M. Caruso

Construction of a new ship dock at a major Philadelphia area refinery required geotechnical design and field consultation. The new dock, which consists of a system of mooring dolphins and platforms, will be capable of docking the Stena V-MAX Oil Tanker (V-MAX). The 1100 ft long V-MAX is currently the largest tanker to travel the Delaware River and will induce significant lateral loads on the new ship dock. Lateral loads induced on the dock will be resisted by over 200 pipe piles installed on a batter. The piles used for support of the dock included 20 and 30 in. diameter reinforced, concrete filled pipe piles. Complete construction of each pile included driving of the pile to the design ultimate capacity, flushing the pipe pile casing clean of overburden materials followed by drilling rock sockets into the underlying Wissahickon Formation. Variations in depth to bedrock, rock quality and degree of weathering and presence of very hard quartzite lenses created a complex geologic environment that presented challenges for the pile/rock socket design and installation. The design of the pile system, installation methods, QA/QC and testing (Pile Dynamic Analysis), as well as the challenges that were encountered through the duration of the project are presented and discussed.

Jan 1, 2008

By Rodrigue Karam

An assessment of the geotechnical conditions at the Manhattan Cruise Terminals (Piers 88, 90, 92 & 94) was conducted after excessive settlement and structural distress was reported at Pier 92. The piers are located on the Hudson River along the west side of Manhattan, New York. The following paper focuses on the investigation and analysis performed on Pier 88 located at the western terminus of 48th Street. The pier is supported by approximately 2,500 timber piles bearing on soft organic silts and clays. The first portion of the analysis consisted of an offshore field investigation and laboratory testing to classify the subsurface soils within the project area and estimate the geotechnical capacities of the timber piles. Additionally, a settlement analysis including consolidation and negative skin friction analyses was performed to evaluate existing settlement levels. Axial and lateral analyses were performed to develop the soil springs (p-y, t-z, and q-z curves) necessary for the structural analysis.

By Scott M. Mackiewicz

This project includes replacement of the historic vertical-lift span Meridian Bridge (U.S. Highway 81 over the Missouri River) that connects Yankton, South Dakota with rural Cedar County, Nebraska. The new 76-foot wide, 1,590-foot long steel plate girder structure required the use of drilled shaft foundations that extended into the underlying Carlile Shale formation. Designers indicated that an individual drilled shaft capacity of about 2,000 kips will be needed at each of the river piers, and based on the subsurface information, 8 to 10-foot diameter drilled shafts extending to about 115-foot would be required for support of the bridge structure. An Osterberg Load Test was performed on one test shaft to determine the ultimate skin friction and end bearing of the Carlile Shale. This paper describes the design and installation of the load test drilled shaft as well as presents the load test results as compared with predicted design values determined using FHWA methods.

Jan 1, 2008

By D. Vanni

Constructing new infrastructure in urban areas increasingly entails the use of sophisticated techniques for soil improvement in order to minimize surface disturbances in adjacent areas and damage to existing structures. In Naples, at the new Piazza Garibaldi subway station, TREVI built a 45 m deep shaft using a hydromill, and utilized soil freezing for the excavation of the four station's tunnels, fifty meter long, located approximately 30 meters below the water table. An innovative use of directional drilling was specially developed by TREVI to successfully complete this challenging job.

Jan 1, 2006

By Ronald E. Walkington

The U.S. Department of Energy (DOE) is building the world's newest accelerator-based, pulsed-neutron system, called Spallation Neutron Source (SNS). The facility, located in Oak Ridge, Tennessee, is a partnership of six DOE national laboratories - Argonne, Brookhaven, Jefferson, Lawrence Berkeley, Los Alamos, and Oak Ridge. Oak Ridge has the responsibility for managing the partnership and ultimately operating SNS. SNS will provide opportunities for up to 2,000 researchers each year from universities, national laboratories and industry from around the world for basic and applied research and technology development in the fields of materials science, magnetic materials, polymers and complex fluids, chemistry and biology. When completed, this state-of-the-art research facility will provide neutron beams that are 12 times more intense than any other such source in the world. Most of the world's neutron sources were built decades ago. Therefore, it is easy to understand how SNS will provide new research opportunities unavailable elsewhere, and at the same time restore United States leadership in neutron sciences. Neutron scattering research provides valuable information about materials that cannot be obtained through microscopy, X-rays, spectroscopes, or other techniques. The information gained from neutron scattering research leads to improved materials that are used in high-temperature superconductors, powerful lightweight magnets, aluminum bridge decks, jet aircraft, compact and computer discs, magnetic recording tapes, shatter-proof windshields, and many other applications. SNS is like a flashing strobe light providing high-speed illumination of an object and will record the structure of physical and biological materials from plastics to proteins. Because neutrons have no charge, they can penetrate more deeply into materials than do X-rays, light, or electrons and thus reveal bulk structure and properties of materials. SNS will help to understand and "engineer" better materials and the manufacture of better products at the atomic level. Our high-technology society demands new materials that are stronger, lighter, and cheaper yet perform well under severe conditions. SNS, which is designed with the future in mind, will be the leading neutron research facility for many years to come.

Jan 1, 2001

By Silas C. Nichols

FHWA Interest is due to: ? An increase in successful projects in the U.S. private sector and in other countries ? Cost effective and more efficient in many circumstances ? Agency Priorities - FHWA "Vital Few" AASHTO TIG

Jan 1, 2005

By Emad Farouz, Roger Failmezger

"The proposed reconstruction of I-75 downtown consists of widening an approximately 2.46 Km section of IR-75 through the northern section of downtown Dayton, OH, USA. Bridge B-13 is a 9-span continuos prestressed concrete I-beam, 319.0-meter (1,048-foot) long bridge with a stub abutment on MSE walls for the rear abutment, and a stub abutment with spill-through slopes for the forward abutment. The piers in the river were located parallel to the Great Miami River, and are full-height reinforced concrete wallsPRESSUREMETER TEST PROCEDUREThe driller advanced either casing or augers approximately 1 meter above the pressuremeter test. Steel casing was used to advance borings performed in the river, and augers were used for borings on land. Mud rotary drilling with a large diameter roller bit was used to remove all of the gravel and cobble fragments inside the casing or augers.At the pressuremeter test elevation the driller used a 63.5-mm (2.5-inch) carbide button bi-cone bit, using a rotation rate of about 60 rpm, a mud fl ow rate of about 10 gallons per minute (40 liters per minute), and an advance rate of 6 to 10 minutes per meter (2 to 3 minutes per foot). To minimize vibrations, advance rates were slower where excessive cobbles were encountered. The 63.5-mm (2.5-inch) O.D. slotted casing pressuremeter was lowered to the test elevation, often requiring either pushing or hammering into the test zone. We believe that the test zone was not perfectly straight, or that gravel or cobble fragments jutted into the test zone and had to be displaced to advance the pressuremeter into the test zone. The slotted casing prevented membrane damage during insertion. A photograph of the slotted casing being lowered into the borehole is shown below.The pressuremeter was calibrated for system compressibility and membrane resistance. At full expansion of 800 cm3, the membrane resistance of the slotted casing was about 2.5 bars.Strain-controlled tests were performed using a Texam control unit with a monocell probe. Volume increments of 20 cm3 were injected into the probe and corresponding pressures were measured. Near the end of the elastic portion of the test, an unload-reload cycle was done. A creep test was performed for 10 minutes at the next volume increment. The test continued until either 800 cm3 were injected or the membrane burst."

Jan 1, 2007

By Juhyung Lee

Recently, large diameter drilled shafts are often used for foundations of large-scale marine bridges with high capacity and required to resist lateral loads. Steel casings are essential in supporting the hole-diving concrete installation of the drill shafts constructed in the sea. The casings, however, are usually not considered as the structural elements and their load bearing capacity is often overlooked in the design of drilled shafts. As the diameter of drilled shafts becomes larger, there are higher demands for more efficient and economical design of large-scaled drill shafts in the sea. Steel-concrete composite columns are popular for the superstructure of bridges, and the outer steel attached to the shaft increases the shaft resistance through confining the concrete. In this study, the lateral resistance of steel-concrete composite drilled shafts was evaluated quantitatively based on the numerical analysis. When steel casings are used as structural elements such as the composite columns. Ultimate lateral bearing capacity of composite drilled shafts with various diameters was numerically calculated through the 3D finite element analysis. For that, elasto-plastic model with the perfect plasticity is involved to capture the ultimate load. A commercial FEA program, MIDAS-GTS, is used in this study. Real field conditions of the west coast, Korea were examined to set up the ground conditions and pile lengths required for this parametric studies. Detailed characteristics of the stress and displacement distributions are evaluated for the better understanding on the mechanisms of the composite shaft behavior.

Jan 1, 2008

By Cornelis Van Der Veen

Foundation piles, partly passing through unconsolidated compressible layers, suffer a downward drag that is called negative skin friction. The negative skin friction depends on the movement of the surrounding unconsolidated soil relative to the pile and on the friction between pile and soil as a function of that movement. The negative skin friction adds to the load on the pile. However as it is a function of the pile movement relative to the soil, the amount of negative skin friction to be taken into account to determine the allowable bearing capacity depends on the allowable pile settlement. In this paper this property is indicated by the factor µ. As under the conditions of ultimate pile bearing capacity negative skin friction does not occur, a factor of safety is introduced, which is lower than normal. Eventually a formula for the bearing capacity is given in which µ and both figure. The exact values for given circumstances have to be determined empirically. A few examples are given.

Jan 1, 2010

By Bengt H. Fellenius

An upgrading and straightening of a highway included building a bridge across a small river. A routine site investigation was initiated to determine the conditions for designing the foundation of the bridge. The proposed bridge was a two-lane highway bridge in one span with a total length of 30 m (100 ft), as indicated in Fig. 1. It was to be placed about 20 m (66 ft) upstreams of the bridge for the existing highway. The site investigation included one boring at each abutment with soil sampling and in-situ vane testing and placed about halfway up the slope from the small river at ground surface elevation + 54 m. Within the investigated maximum depth of 40 m (130 ft), the soils at both borehole locations consisted of a thin clay crust over a thick deposit of soft sensitive clay with a natural water content of about 70 % and a liquid limit of about 60. The undrained shear strength below the crust was about 20 KPa (400 psf) and increased slightly with depth. The sensitivity was high, about 40.

Jan 1, 1987

By Ahmed H. Bukhary, Naser A. Al-Shayea

The objective is to assess the overconservatism in the parameters used for designing offshore piles. Methodology includes analysis of shaft friction data obtained from more than five different locations in the Arabian Gulf, consisting of 40 piles to depths up to 86 m. Reports were collected for both the dynamic pile monitoring system (DMS) and their corresponding geotechnical reports based on the American Petroleum Institute (API). The values of shaft capacity for the sand layers were analysed by comparing those based on API to the corresponding DMS values. Results of the comparison of the data from these reports showed that the pile design parameters obtained using API guidelines is generally smaller than that measured by DMS. The difference is presented in terms of an overconservative factor (OCF) which is adjusted based on statistical nonparametric test performed on the two data sets. The adjusted OCF were found to be 1.79 and 2.00 for carbonate sand at (loose to medium dense) and (dense to very dense) conditions, respectively. The corresponding values for silica sand were only 1.2 and 1.06. In conclusion, based on the evaluation conducted for data from these reports, the API shaft friction is overconservative for carbonate sand. The API shaft friction for piles in sand can be increased by multiplying it by the adjusted OCF.

By A. Tejchman

On the site of building of a new flyover founded on piles the comprehensive "in situ" investigations were carried out. The subsoil conditions under each of 15 supports were very differentiated. Using of the static sounding results a new method for evaluation of bearing capacity and settlement of piles was proposed. The method is based on a special construction of the curve of load-settlement relationship. The verification of this method was made on the basis of loading of piles.

Jan 1, 2010

By Hyung-Min Kwon

There are a number of methods available that can be used to estimate the bearing capacity of piles that are subject to lateral load, such as the theory of subgrade reaction or the elastic continuum approach. The objective of these approaches is to determine the lateral load corresponding to the allowable lateral displacement of the pile. It is important to select the appropriate soil stiffness when analyzing soil behavior within the allowable displacement of piles because the stiffness of soil is dependent on the displacement of piles. Even though pressuremeter tests can measure the stress-strain behavior within a wide strain range, pressuremeter test results have been utilized to assess only the fragmentary soil modulus based on either semi-empirical correlations or analytical approaches. This study is concerned with a methodology that can estimate the horizontal deformational property, while taking into consideration the nonlinear deformational characteristics of sandy soils. Pressuremeter tests were conducted for 15 cases using a calibration chamber. Reloading curves were employed in the estimation of horizontal deformational property in order to minimize the effect of soil disturbance caused by the installation of the probe. The shear modulus degradation characteristics were estimated from the curve fitting for the reloading curve and from extrapolation using the exponential function. In addition, the difference was taken into account between the stress state around the probe in reloading and that of the in-situ state. A consistent relationship was observed between the maximum shear modulus taken from the suggested method and the bender element tests performed in the calibration chamber, simultaneously with the pressuremeter tests. In addition, the results showed significant concurrence with the well-known empirical correlation.

Jan 1, 2008

By Emad Farouz, Roger Failmezger

"The proposed reconstruction of I-75 downtown consists of widening an approximately 2.46 Km section of IR-75 through the northern section of downtown Dayton, OH, USA. Bridge B-13 is a 9-span continuos prestressed concrete I-beam, 319.0-meter (1,048-foot) long bridge with a stub abutment on MSE walls for the rear abutment, and a stub abutment with spill-through slopes for the forward abutment. The piers in the river were located parallel to the Great Miami River, and are full-height reinforced concrete walls. PRESSUREMETER TEST PROCEDUREThe driller advanced either casing or augers approximately 1 meter above the pressuremeter test. Steel casing was used to advance borings performed in the river, and augers were used for borings on land. Mud rotary drilling with a large diameter roller bit was used to remove all of the gravel and cobble fragments inside the casing or augers.At the pressuremeter test elevation the driller used a 63.5-mm (2.5-inch) carbide button bi-cone bit, using a rotation rate of about 60 rpm, a mud fl ow rate of about 10 gallons per minute (40 liters per minute), and an advance rate of 6 to 10 minutes per meter (2 to 3 minutes per foot). To minimize vibrations, advance rates were slower where excessive cobbles were encountered. The 63.5-mm (2.5-inch) O.D. slotted casing pressuremeter was lowered to the test elevation, often requiring either pushing or hammering into the test zone. We believe that the test zone was not perfectly straight, or that gravel or cobble fragments jutted into the test zone and had to be displaced to advance the pressuremeter into the test zone. The slotted casing prevented membrane damage during insertion. A photograph of the slotted casing being lowered into the borehole is shown below.The pressuremeter was calibrated for system compressibility and membrane resistance. At full expansion of 800 cm3, the membrane resistance of the slotted casing was about 2.5 bars.Strain-controlled tests were performed using a Texam control unit with a monocell probe. Volume increments of 20 cm3 were injected into the probe and corresponding pressures were measured. Near the end of the elastic portion of the test, an unload-reload cycle was done. A creep test was performed for 10 minutes at the next volume increment. The test continued until either 800 cm3 were injected or the membrane burst."

Jan 1, 2007

By Gerald Verbeek

There are certain concepts that seem to invite responses from some, including some in the foundation industry and even some within DFI, that are at best surprising. Business owners and their employees share the desire that their company does well and continues to operate. Maybe company growth is not always realistic but maintaining the current level of activity is in the least what they hope for. In other words, they hope that their company is sustainable, and they are fully behind that notion. But when the concept of sustainability is raised, there is, at least with some, suddenly doubt that that is a good thing. And yet, that concept only aims to achieve at a grander scale what the owners and employees desire for their company. There are many definitions of the term sustainability, but probably the most commonly used description is that framed by the United Nations in 1987. It states that sustainability is the concept of meeting the needs of the present without compromising the ability of future generations to meet their own needs. Arguably that definition is too abstract and does not provide the type of specific goals and targets we are used to. To help with that, to some extent, in 2015 the United Nations formulated 17 Sustainable Development Goals (SDGs), to provide "a shared blueprint for peace and prosperity for people and the planet, now and into the future." And undoubtedly those SDGs are fodder for those that question the concept of sustainability in the foundation industry. How can our industry, they wonder, ensure that there is no poverty or hunger (SDG 1 and 2), and the climate action goal (SDG 13) immediately leads to the hot button topic of global warming. And maybe this is where advocates lose (some of) the sceptics of the sustainability concept, but hopefully they will continue to read this article that lays out why sustainability simply makes sense, also for the foundation industry and especially for DFI.

Nov 1, 2022

By Jorj O. Osterberg

The practice of using side shear resistance in the design of drilled shafts socketed in rock is discussed. In the absence of field test data for the particular rock involved, the designer often neglects the side shear altogether or uses an extremely conservative value. The uncertainty of using strength data from compression tests on rock cores is discussed. Examples of full scale load tests are given which illustrate that even in the weakest of rocks, considerable side shear resistances are obtained, enabeling reductions in the depths of the sockets and consequent savings. Existing Practice. The existing design practice in using side friction/bond between a drilled shaft in rock or hard soil varies very considerably in different areas of the U.S., in different areas of the world, among different Geotechnical Engineers, and in the requirements of different building codes. In fact, the variation is so great that it is inconsistent and contradictory. For example, in Florida where fairly weak coral limestone and sandstone is prevalent, the general practice is to use side friction only and to allow no end bearing. In Chicago, Detroit, Boston and other areas where soft clay overlies stiffer clays, hardpan and limestone or other hard rock, the common practice is to allow for no friction and to use end bearing only, even though the lower portion of a shaft frequently penetrates stiff to hard clays and hardpan (glacial till) before bearing on hardpan or rock. In Hong Kong, if the hole is stabilized with drilling mud, no end bearing is allowed. In Boston (Thompson, Erikson, and Smith, 1989), two tests at two sites on 18 inch pipe piles penetrating 100 feet of soft clay and driven only inches into an argillite, tested 140 and 210 tons in ultimate side shear resistance. Certainly, with long drilled shafts, no matter how soft or weak the soil or rock is, some if not considerable side friction occurs, and where drilling mud is used, there must be considerable end bearing.

Jan 1, 1991

By Jorj Osterberg

550 load tests of up to 150 MN have been completed on driven and bored piles using the Osterberg Load Cell. Because the test measures side shear and end bearing separately, much can be learned about the forces on the pile as it is loaded to ultimate capacity. At working loads side shear almost always far exceeds end bearing, with the distribution of shear and bearing greatly affected by disturbance occurring during drilling operations. Since much less movement is required to mobilize side shear than end bearing, most of the bearing develops after the working load is exceeded. Thus with insufficient bottom cleaning, safety against excessive settlement can be considerably reduced. Improved methods of drilling, hole cleaning, rebar cage installation and concrete placement are discussed. For rock socket piles it has been found that the ultimate test load far exceeds the working loads in most cases. This is almost always due to greater penetration into the rock than is required for adequate safety against excessive settlement. Factors affecting rock socket capacity are discussed. Increase of side shear and ultimate capacity with time is discussed. Case histories for driven and bored piles in soil and rock sockets are described.

Jan 1, 2001

By Masakazu Takano, Koji Suzuki, Naotoshi Shinkawa

"Cement deep mixing (CDM) method successfully applied to a marine construction project in northern Vietnam is reported. The method is classified as wet method, in which cement slurry is injected into the ground. Thickness of clayey deposit subjected to improvement is from 20 m to 28 m, and the total volume of CDM improvement exceeds 460,000 m3. This is the first massive application of CDM method in the region. Three CDM barges, each equipped with four mixing shafts, were brought to the site in order to finish CDM work within a period of seven months. Cement content used in the work was 180 kg/m3 and water-cement ratio of slurry was 100%. Unconfined compression strength of stabilized soil was 1,200 kPa to 1,600 kPa in average with coefficient of variation from 0.3 to 0.4. Statistics analysis of the strength with these values gave percentage of lower strength less than 10%. Trial use of needle penetration test performed to study strength profile of a CDM column is also reported.INTRODUCTIONThe site of Lack Huyen Port Infrastructure Construction Project is located in the sea adjacent to Cat Hai Island, offshore Hai Phong city which is around 100 km east of Hanoi, the capital of Vietnam. Left side of Fig. 1 shows the location of the site. The project contains development of container terminal, dredging of waterway, construction of sand protection dyke to prevent waterway from being buried, and bridge construction to connect the island to the mainland.Joint venture of Penta Ocean Construction and Toa Corporation was awarded Package 6 of the project, in which reclamation of container terminal area, retaining wall construction and terminal road construction were included. Plan of the site is presented in right side of Fig. 1. The site work has been started in June 2013 and is scheduled to finish within 4 years."

Jan 1, 2015

By Shenbaga R. Kaniraj

The pile loading tests are generally conducted to assess the safe load on piles in compression. In the Indian practice, the safe load is determined using the pile loading test data and the two criteria specified in the Indian Standard Code, IS.2911 (Part 4) -1985. For this, the test pile should have undergone a minimum displacement equal to 10% of the pile diameter. Often, the piles are not subjected loads that are sufficient to cause a displacement of this magnitude. If the settlement is at least 12 mm, then the safe load is determined based only on the first criterion. But, if the settlement is less than 12 mm, the safe load cannot be determined using the IS Code criteria. The paper presents two procedures called hyperbolic and generalized hyperbolic methods to estimate the safe load using the IS Code criteria even when the loading test data is insufficient. The data from two initial tests have been analyzed. The predicted safe loads have been compared with the actual safe loads.

Jan 1, 1996