Search Documents

By M. Melih Demirkan, Juan J. Gutierrez, Raghav Ramanathan

"As the capital of the United Arab Emirates (UAE), Abu Dhabi is one of the world’s fastest-developing cities. To sustain its significant growth rate, Abu Dhabi must surmount challenging engineering problems in the most efficient manner. One of the challenges facing Abu Dhabi is ground settlement caused by poor groundwater control practices in inherently difficult subsurface conditions. For construction projects in Abu Dhabi located near the Arabian Gulf, groundwater is frequently encountered and must be accounted for and addressed during design and construction. Abu Dhabi City CenterRecently, the Abu Dhabi government developed a geodatabase by digitizing, processing and qualifying an extensive amount of existing information (i.e., more than 26,000 borehole logs). Because of the evaluation and processing of the geodatabase, detailed maps of geotechnical and hydrogeological surface features were generated using 3D modeling. Ultimately, the geodatabase was used to develop risk maps indicating geohazards, such as sabhka (or salt flats), uncontrolled fill and cavities. This information identifies the location and extent of the areas vulnerable to surface subsidence. Dewatering can change pore water pressure, which, in turn, alters the effective vertical stress in a soil mass and can affect groundwater chemistry. Changes in pore water pressure and groundwater chemistry can significantly affect soil and rock. The potential effects of dewatering include:• Change in effective stresses and shear strengths in soils• Increase in seepage velocities and pressures• Erosion or transport of soil particles and piping• Settlement• Collapse of subsurface cavities or voids• Transport of groundwater containing contaminants• Dissolution of soluble materials, such as rock salt or gypsum"

Jan 1, 2017

By Colin Curtis

In recent years, Manchester Airport has undergone expansion including the construction of a second runway, a new terminal building (Terminal 3) and extensions to the existing Terminal 1. Manchester is Britains third largest airport and ranked 20th in the world for international traffic. Arup (Manchester) was engaged as consulting engineer in a multi-disciplinary role for the terminal works. Part of this was a geotechnical commission including site investigation and pile design followed by supervision. This paper reviews the piling for the old, new and terminal extensions. In total, five pile types have been utilised over the years. The original 1950's Terminal 1 was founded on driven cast in situ piles, with a later 1970's extension utilising rotary augured piles. The recent piling comprised continuous flight auger piles (CFA), driven steel tube and tripod bored; the latter in areas of restricted access or low headroom. The ground conditions are Made Ground over thin Alluvial and Glacial drift, in turn, over a generally weak to moderately weak gypsiferous mudstone. All the piles were socketed into the mudstone. In terms of the new CFA piles, quality control using the instrumentation monitoring was problematical, but a substantial static load and integrity test programme resolved pile performance. Part of the work is matching new pile performance with previously installed piles and the continued use of older piles with new loads. Research provided some data on the older piles, including some static load test data, which enabled back analyses of their design and likely behaviour. Differences in design methods, installation techniques and pile behaviour based on load tests will be discussed.

Jan 1, 2001

By G. G. Goble

Dynamic pile testing is now over 20 years old as a routinely applied tool for evaluating driven pile installation. The first test on a cast-in-place pile was performed more that 15 years ago. The research that produced the method began almost 30 years ago. But, questions still arise regarding the appropriate use of this technique so some review is useful. Today a number of methods including dynamic testing all depending in some way on the application of dynamics are in routine use. First, Wave Equation analysis can be used to predict pile driveability before going to the field. The same approach can be used during driving to estimate the bearing capacity based on the blow count observed in the field. Dynamic measurements, on the other hand, can only be used after pile driving has begun. They offer predictions of pile capacity as well as measurements of hammer, driving system, and pile driving performance characteristics. The first part of this paper will be devoted to discussing how the foundation engineer can use these tools. First, a brief review of what dynamic methods actually do. In Wave Equation analysis a numerical model of the hammer, driving system, pile, and the soil is created by the engineer. The hammer is dropped on the pile and using a discrete, dynamic analysis the motion of the individual pile elements is calculated as a function of time. Of course, input information must be supplied by the program user to describe the hammer, driving system, pile, and soil. In the current state of development, the primary problem in input data is with the hammer performance (efficiency) and the soil description. Research may be able to do a better job with the soil data, but hammer performance will always vary from hammer to hammer and is dependent on the affectiveness of the inspection process. Prior to beginning pile driving the Wave Equation analysis supplies the best available estimate of what will happen when driving begins. It gives an estimate of blow count during driving, driving stresses, both tension and compression in the pile, and for diesel hammers, stroke. The selection of the driving system can be checked with the results of Wave Equation analysis and modifications can be made if required. For example, if the blow count at the required capacity was deemed excessive by the contractor a larger hammer could be tried or if driving stresses were too high changes could be made in the cushion or the hammer selection could be modified. All of these modifications are possible with only the cost of a computer run. The primary questions regarding the accuracy and reliability of Wave Equation analysis at this time is with regard to the assumptions made to represent the soil characteristics and the difficulty in predicting hammer performance.

Jan 1, 1993

By Sivilay Sayavong, David Puller, Julian Gatward, David Hard, Martin Stanley

"AbstractThe Thames Water Tideway Tunnels programme involves the upgrade of London’s combined sewer and storm water system. The first section is the Lee Tunnel between the Beckton Sewage Treatment Works (STW) and the Abbey Mills Pumping Station. This will intercept the overflows currently discharging to the River Lee and has the capacity to store and transfer 350,000m3 of storm water and sewage. The project required 4 shafts and a 6.9km 7.2m diameter tunnel. The shafts are some of the largest ever constructed in the UK, with diaphragm walls up to 98m deep and 1800mm thick. As a result of the innovative methods of diaphragm wall design and construction adopted the 4 very large and deep shafts were able to be excavated and completed safely, with minimal water ingress and with extremely high quality.MVB, a joint venture of Morgan Sindall, Vinci Construction Grands Projets and Bachy Soletanche are delivering the £635m contract with Thames Water’s Project Management Team in a collaborative manner under an NEC contract. Mott MacDonald, Morgan Sindall UnPS & Bachy Soletanche are acting as designers.Some of the important advances in diaphragm walling made included:??Diaphragm wall design to both EC2 & EC7 taking into considering the assessment of chalk stiffness, high hoop stresses, large multiple openings and non-axisymmetric loadings.??Formation of shafts as a faceted circle from a series of overlapping panels, with primary panels up to 7.2m wide demanding concrete volumes up to 1300m3 be poured in one go. Overlapping secondary single bite panels cut into the grade C50/60 concrete.??Excavation of the full geological stratigraphy of London making bentonite management complex.??Panel verticality of 1:300 required over the full depth. The results achieved this and in many cases exceeded expectations with some panels coming in at up to 1 in 800 with the majority at 1 in 400 to 1 in 500. The project is also the first in the Soletanche Bachy Group to take data from the ultrasonic drilling monitor used to check the verticalty in electronic format in order to create 3D CAD as-built drawings.??Each diaphragm wall panel was reinforced over its full depth. Up to 18 separate pieces of reinforcing cage had to be installed in primary panels. Cages underwent a full range of temporary works designs to check that lifting, splicing and placing could all be undertaken safely. Fibreglass was used in the tunnel portals in the shafts to ease breakthroughs."

Jan 1, 2014

By Sugie Prawono

Jacked pile is the only piling system in which the load capacity of the pile, at any penetration depth, could be monitored directly during its installation process. Each installed pile could have a graph of jacking load versus depth of penetration. For safety purposes, the maximum applied jacking load during installation of a pile could be assumed as the minimum load capacity of the pile. This load capacity will increase with time since the drop in soil strength due to the installation process will recover later on. In order to determine accurately this jacking load, a research was carried out by comparing the load capacity of a pile at certain depths to the jacking load recorded during the installation process. The load capacity could be calculated using cone resistance, qc, and local friction, fs, from Dutch Cone Penetration Test. A graph could be drawn of the load capacity against the depth. By applying a correction factor, a, to the data of local friction, the calculated graph could be matched to the graph of recorded jacking load. The a factor is found to depend on the soil type, which is in this case, represented by the magnitude of cone resistance. The soil type is divided into 3 categories according to qc values (qc < 500 Kpa; 500 Kpa < qc < 2000 Kpa and qc > 2000 Kpa). Graphs of the a factor versus depth and a sample of calculation are presented in this paper for easy application.

Jan 1, 1999

By Andrea Gambi, Giancarlo Olivucci, Maurizio Lenzi

"In the paper a criterion for the evaluation of the sharing of the lateral loads in a piled foundation is presented. It relies on the the compatibility condition between the rotation of the rigid pile cap and the rotations of the pile heads, following in that the criterion suggested by the Eurocode 8 - Part 5. This assumption leads to an analytical solutions which allows to deal with the sharing of the lateral loads and moments by means of two main interaction parameters only. A sharing domain is also derived and it shows the role played by the eccentricity of the lateral load on the values of the axial forces and of the bending moments at the head of the piles.INTRODUCTIONIt is well known that the interaction among soil, piles and foundation is one of the most complex subject to deal with in Geotechnical Engineering. Its rigorous study needs to employ suitable finite element software nowadays available and able to take into account the non linear behavior of the soil as a continuum and the inelastic response of the structure. A deep insight to the topic of the sharing of the loads cannot obviously renounce to this approach.On the other hand it is a daily need of the designers to have at their disposal simple tools that allow to make preliminary evaluations of the basic equilibrium conditions. To this purpose many methods of analysis have been developed in the past to face the sharing of the loads in a simplified version. The present contribution follows this way trying however to introduce some improvements that leads to find a solution that satisfies both the equilibrium of the forces and the compatibility of the movements (Lenzi, Gambi, Olivucci, 2002). The proposed model allows to identify the basic parameters which govern the sharing of the lateral load and it allows to perform also parametric analysis and quick checks that may be useful in the design of the piles."

Jan 1, 2005

By J. Pei

The studies of dynamic measurements using stress wave theory has commenced in China. This paper introduces some practical experiences using "CASE method" in Shanghai showing applications of dynamic measurement to determine ultimate bearing capacity of pile, the change of capacity due to set up, determining the optimum bearing layer during pile driving, the efficiency of hammer system and integrity of pile and discussions of method concered.

Jan 1, 2010

By Gerald E. H. Verbeek

As the number of driven concrete piles with Embedded Data Collectors increases, it has become possible to compare the widely used Beta Method to assess pile damage (using the change of pile impedance) with the so-called Measured Pile Integrity (MPI) method (a combination of two approaches using both the change of pile impedance and the change in pile pre-stress levels). After a brief introduction of both methods, this paper presents the outcome of that comparison based on data from more than 400 concrete piles driven in Florida, which brings into question the reliability of any damage assessment method based solely on the change of pile impedance (such as the Beta Method), especially to detect damage near the pile toe. Moreover the paper demonstrates the need to re-assess the damage classification used for the Beta Method as well as the use of Pile Driving Analysis (PDA) to detect pile toe damage.

Jan 1, 2011

By Mostafa Mossaad, Ali Helwa, Manal Salem

Support of excavation (SOE) design practice tends to model SOE elements using two-dimensional (2D) analyses to avoid the complexity associated with three-dimensional (3D) analyses. Such practice overlooks soil arching in the horizontal plane and prevents designers from accounting for elements such as capping beams as part of the statical system. This study simulates square excavations supported by cantilever slurry walls in dry cohesionless soil using 2D and 3D finite element (FE) models. First, side support wall behavior is compared from 2D and 3D FE models for variable excavation length to depth (L/H) ratios. Second, the effect of slurry wall lateral bending stiffness on wall behavior is studied by modeling the wall using plate element with isotropic and anisotropic wall stiffness. Finally, the sensitivity of cantilever wall behavior to the presence of capping beam is illustrated. The study concludes that unbraced excavations with L/H ratios greater than 5 almost resemble plane-strain conditions. Slurry walls are better simulated in 3D FE models by dividing the plate element into discrete panels or by assigning anisotropic bending stiffness to the plate element. Finally, the presence of capping beam affects the behavior of cantilever walls resulting in reduction of deflections and redistribution of bending moments. INTRODCUTION Support of excavation (SOE) design practice ranges in complexity from conducting simple hand calculations to performing three dimensional numerical modeling depending on several factors among which is the geometry of the design problem. This paper addresses walls that are designed using numerical modeling, and discusses the factors governing the choice of the most suitable modeling approach. It has been believed for a while that modeling excavations using 2D numerical models would lead to a more conservative solution, which turned out to be incorrect in specific cases. This paper attempts to describe cases where 2D finite element modeling could be on the conservative side and other cases where it could be less conservative than the more complex 3D modeling.

Jan 1, 2018

By Thomas Lardner

Excavation for The Bow, EnCana, in downtown Calgary, occurred between May 2007 and September 2008. A monitoring programme was used to determine the behaviour of the shoring wall, soil and bedrock during the excavation for the 21 metre (69 ft) deep excavation with a footprint of approximately 17,000 m2 (183,000 sq ft). Results from the inclinometer readings indicated that significant horizontal movement due to a weak rock layer and shear band effect. These modes of movement account for up to 100 mm (4.0 in) and 45 mm (1.8 in) of lateral deflection, respectively. Based upon the results of the monitoring programme, rock samples were collected from the weak mudstone bedrock, with great difficulty, to determine the strength and deformation parameters. Results from the uniaxial compression tests indicate a UCS around 830 kPa (120 psi) and elastic modulus between 80 and 180 MPa (11 and 26 ksi). Mohr-Columb parameters were determined to be c&apos; = 340 kPa (49 psi) and f&apos; = 24°. Residual strengths were determined to be c&apos;r = 0 and f&apos;r = 15°. Using the results of the laboratory tests and field investigation records, an initial finite element analysis was conducted. Results of the analysis show good correlation when compared with the observed monitoring deformation, indicating accurate portrayal of rock parameters. Additional analysis and investigation is required to determine the principal horizontal stresses in magnitude and direction.

Jan 1, 2010

By John L. White

The vibro driver/extractor is a machine that grips to a pile and vibrates it up and down. When the vibrating pile is lowered into the ground, all soil around the pile begins to vibrate. A vibrating pile breaks the friction between the pile and the soil, thus allowing it to penetrate the ground. A vibro is usually operated by hoisting it into the air with a crane and then placing it onto the pile. The vibro has hydraulic gripping jaws that are controlled from the ground. Once the operator has successfully lowered the vibro onto the pile, the jaws are closed and locked onto the pile and operations can begin. Please see the drawing below: [ ]

Jan 1, 1990

By Javier Rodriguez

Adaptive re-use of existing structures in urban environments has become very common due to lack of available space in our cities and requirements for increased structural capacity. Often, it involves retrofitting existing foundations to support increased loading. In such cases, Engineers face the need to review existing deep or shallow foundations for their true load carrying capacities in order to determine the required magnitude of retrofit work, if any. To accomplish this, the engineer must track down and cull through the existing construction documentation to determine what was actually constructed, complete an investigation to confirm these conclusions, possibly sample the foundation elements for strength properties, and on occasions complete non destructive or full scale load testing of indicator elements. This paper describes the typical procedure followed by the authors for design of retrofit schemes for existing buildings in the Washington DC metropolitan area. Three case histories are presented that illustrate various issues encountered during design.

Jan 1, 2006

By Ali Porbaha

The use of soil nailing technology as a cost effective alternative for excavation support and slope stabilization has substantially increased in the United States during the last decade. For example, in the past thirteen years, more than 185,800 square meters of soil nail walls have been constructed in California alone. The conventional soil nail systems pose difficulties when ground conditions are subject to caving, for instance for silty sand (sugar sand) or cobbles and boulders. The construction industry has developed self drilling hollow bar systems (or pressure injected bored, IBO) that combine both drilling, placing and grouting in a single operation as a solution to speed up construction. While the system is extensively used for temporary applications, nevertheless, some concerns, particularly about corrosion, has limited the use of this technology as a permanent system in North America. This study presents several issues related to self drilling soil nail systems, the results of a field investigation and a summary of the research project.

Jan 1, 2006

By G. Noce

The ever more present necessity for greater precision in foundation structures on vertical piles subject to horizontal forces applied to the heads, in the light of of the latest knowledge about the elastic-plastic behaviour of the soil has led to the use of numerical calculation for the formulation of a general resolution method for the problem. The calculation method that will be set out, applicable to piles with inertia moments variable discreetly along their axes is especially useful when studying steel structures for medium and large tonnage vessels for which the metal piles are often constructed for the assembly of section of equal external diameter but different thickness and therefore different inertia moments. Two examples are given of constructions whose foundations have been projected with these calculation tools, one in the railway sector (foundation pile for the river Nera viaduct - Italy) important for the limitation of horizontal relative deck displacement, the other maritime (Dolphins of the petroleum pier of the port of Bandar Abbas - Iran).

Jan 1, 1989

By Wu Jian-tao, LI Guo-wei

"The Cement Mixing Pile (CMP) quality assurance assessment is an important programme in evaluating the efficiency of foundation improvement. Coring is the current specified method of quality assessment in China which has the shortcomings of long cycle, high cost and low efficiency. The field and laboratory test show that the regular cone penetration test can only detect maximum of 4m of effective detection depth in CMP. In contrast, the method of cone penetration test in the reserved hole can detect the quality continuously along the pile at any depth. The tip resistance of reserved hole penetration in the 7th day has good linear relationship with unconfined compressive strength in the 28th day. The slope of linear relationship decreases with the increasing of clay particles content.INTRODUCTIONThe method of Cement Mixing Pile (CMP) is often used to improve soft soil foundation in highway construction, with the major purpose of reducing settlements under embankments (Bruce et al., 2000),which is a form of what is known as the Deep Mixing Method (Bruce et al., 2013). The CMP technology spread quickly in China in the 1980s. CMP quality assurance assessment is an important programme in evaluating the efficiency of foundation improvement. Coring is the current specified method of quality assessment in China (China Academy Of Building Research, 2002). The method of Coring is perceived in some quarters that samples will provide lower strengths given the distress caused to the core during drilling and extraction (Bruce et al., 2002).The cone penetration test CPT can provide continuous measurements of the penetration resistance, sleeve friction at the tip of the probe, which has advantages of simple operation, low cost and high efficiency compared with coring. However, CPT tests have not been established to assess CMP in Sweden because of difficulties in maintaining verticality (Larsson, 2005). In Finland and Norway, however, CPT tests are commonly used (Halkola, 1999). One of the disadvantages of CPT is the tendency of the cone to steer out of the column (Porbaha et al., 2003). Darya Mokrousova (2010) states this tendency to deviate can be overcome by pre-boring and starting the penetration test from the base of the pre-bored hole. Sheng Haiyang (1999) found that probes may be deflected out, sometimes even at small penetration depths, and may not give a complete inspection of the pile. Liu Songyu et al. (2003) suggested that the Standard Penetration Test (SPT) is an effective way to evaluate the strength and quality of stabilized soil-cement columns. In general, Regular CPT can’t test the full length of CMP, and SPT still needed drilling which causes discontinuous detection. From the existing standard of China, core sampling compressive strength test is the main method, evidently, coring displays a longer test cycle, high cost and low efficiency. Therefore, an improvement of CMP quality assessment, by conjuring a fast and reliable detection and evaluation method, is necessary. The aim of this paper is to research the feasibility of using CPT in assessing the quality of CMP and presents an improved CPT method."

Jan 1, 2015

By F. Castelli

A simplified non-linear method to predict the behaviour of a single pile and/or pile group under horizontal loads is presented in the paper. The evaluation of the non-linear lateral deflection is based on a procedure taking into account the decrease of the model stiffness with the increasing of the applied load. The solution derived firstly for the single pile, was extended to the case of a pile group introducing the p-multiplier (fm) concept proposed by Brown et al. (1988).

Jan 1, 2006

By George Piscsalko

"Quality control of drilled shafts and CFA piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult or not possible to fully inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. CFA piles are cast with no ability to inspect the shaft prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and CFA piles. This paper will compare evaluations by three existing non-destructive test (NDT) methods with a new method of Thermal Integrity Profiling for assessing integrity in drilled shafts and CFA piles. This Thermal Integrity Profiling method determines the integrity over 100% of the shaft cross section, both inside and outside the reinforcing cage, by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements are made typically only 12 to 48 hours after concrete placement, thus accelerating the construction process. Thermal Integrity Profiling will be described in detail and the Thermal Integrity Profile (TIP) results from several shafts with purpose built defects will be discussed along with several case histories from drilled shafts and CFA piles where Thermal Integrity Profiling was used. The case histories will compare TIP with various other NDT tests utilized on these particular piles including comparisons with Low Strain Integrity Testing and Cross Hole Sonic Logging. Test results for the various methods will be discussed and the excavation of the upper portion of one drilled shaft will be shown and discussed. IntroductionDrilled shafts can be a desirable foundation element in many applications due to the large axial and lateral capacities which are attainable for very large drilled shafts. Drilled shafts can be cast in a dry hole which allows for inspection of the hole prior to casting, but the casting process is very difficult to nearly impossible to inspect with any accuracy. Drilled shafts are frequently cast under slurry as a means to stabilize the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to accurately inspect the hole prior to casting and it is equally difficult to inspect the shaft during the casting process. CFA piles are another popular choice for their relative ease and speed of installation. The trend has been larger CFA piles carrying greater loads, which makes quality control critical for these piles. Many of the above mentioned processes are blind to inspection and therefore the chances increase for having defects present in the completed elements."

Jan 1, 2014

By E. C. Demsky

This paper describes the large diameter caisson foundation for the upstream guidewall at the Lock and Dam No. 26 (Replacement) Project. The guidewall is supported on two rows of 1.8-m diameter concrete filled caissons. The 28.8 m long caissons are embedded 15.5 m into the foundation material and have an unsupported length of 12.2 m. This paper describes the philosophy and design decisions leading to this unique caisson design. The construction success and problems for the load test caisson will be discussed. The full scale 13,350-kN caisson load test and the associated lateral load tests will be described and the test results presented.

Jan 1, 1989

By Ambarish Ghosh, Rituparna Dey, Indrajit Chowdhury

"In port and harbor facilities, jetties and cargo berth terminals are usually installed on piles that remain partially embedded in soil, while a part of it behaves as columns supporting top deck. Technology in vogue adapts a pseudo static analysis in computer where the top deck including piles are analyzed as an integrated system based on finite element method when the piles are modeled as beam elements, while the soil in which it is embedded is modeled as linear or nonlinear springs. Typical berthing force of the ship is considered as a pseudo static force where the dynamic characteristics of the force is taken into consideration by an equivalent impact factor and little study exists on the actual behavior of these type of piles under the transient shock due to berthing impact. Present paper proposes an analytical solution based on which one can compute the dynamic response of such jetty piles considering shear modulus of soil constant with depth. Considering the solution is analytical in nature no special software is needed and can well be adapted fordesign office practice using generic utility software like MATHCAD, MATLAB etc. that makes theproposed model computationally very efficient.INTRODUCTIONResponse of piles under dynamic load has been an important study in the realms of civil engineering, where significant research has been carried out on its dynamic behavior under harmonic loads like one experienced in a machine foundation or under seismic force.A number of researchers have given solution to this problem like Parmelee et al (1964), Tajimi (1966), Penzien (1970), Novak et al (1974, 1983), Banerjee and Sen (1987), Dobry and Gazetas (1988),Chowdhury and Dasgupta (2008).However, most of these theories are based on piles loaded under harmonic load and valid for long piles where structural failure precedes the soil failure considering the piles are long and flexible."

Jan 1, 2015

By Osamu Taki

This paper presents the system, the strength of column, the design concept, and the applications with four case histories from the past project as the general aspect of Geo-Column (trade mark of single soil-cement column by SCC Technology, Inc.). In the system, it shows the installation process and drilling/mixing tool with the mixing process. In the design concept, it shows how to design Geo-Column against the vertical and horizontal load. Finally, it shows the applications with four case histories, (1) building mat foundation, (2) isolated foundation on the pedestrian bridge, (3) bridge spread footing and slope erosion control wall in the channel, and (4) cut-off wall and shoring wall in the underpass roadway to the railroad.

Jan 1, 2000