Search Documents

By Chu E. Ho

Jet grout column formation at large depths are prone to several uncertainties, such as inaccuracy in setting out boreholes, drilling deviation, soil variability and reduced jetting energy at the nozzle. This would result in shorter cutting distance of the jet, with potential lack of interlock between grouted columns. A design strategy for mitigating the risk should include a soil investigation program aimed at discovering potential variability in soil conditions at the locations of jetting. Determination of soil strength profiles with depth would be useful for evaluation of jetting parameters and prediction of the achievable cutting distance at any depth. Selection of design column spacing should include allowance for setting out accuracy, verticality of the boreholes and the achievable jet cutting distance. For deep jet grouting operations, it would be necessary to take into account the energy losses at the nozzle inlet; however the increase in the presiding pressure at the nozzle outlet at depth is small relative to the range of jetting pressures commonly employed and would not affect the cutting distance to any significant degree. Design column spacing should not be so close as to cause problems with ?masking? which may lead to localized ungrouted zones of soil. For effective field control, boreholes should be cased up to the top elevation of the grouted zone so that the orientation of the borehole can be measured prior to grout injection. An analytical equation for calculating the cutting distance is proposed for adjusting jetting parameters where necessary to compensate for drilling deviation and changes in soil conditions. It is preferable that jet grouting trials be executed at elevations that correspond to the actual production jet grouting depths for accurate evaluation of jet cutting performance.

Jan 1, 2008

By Wen Songlin

This paper presents an experimental program to investigate the behavior of a pile with wings under horizontal loads in sand at laboratory. The work focused on evaluating the lateral resistance behavior and the geometric effect of wing board on the horizontal resistance. Based on the measured data and observed phenomenon, the following behaviors have been observed: 1) A pile with wings is not only a powerful means to improve the horizontal bearing capacity of a pile foundation but also economy and feasibility; 2) The horizontal bearing capacity of a pile with wings increases with increasing of it?s wing board?s area; 3) The pile lateral capacity is also influenced by the wing board?s geometric shape. Under a certain soil and pile condition, there is a critical embedment depth of the wing board, which will yield the maximum horizontal bearing capacity. It was further observed that when the displacement of the pile head increases, part of the horizontal bearing capacity of the pile is developed by the so-called shaft?s anti-pulling capacity.

Jan 1, 2007

By I. D. McPherson, Dominic P. Mahoney

The Metro Sports Facility is currently under development in Christchurch, New Zealand and is a key Anchor Project in the city’s post-earth quake recovery. When completed it will be largest indoor sports and swimming pool complex in New Zealand, with a building footprint in the order of 22,000m2. The site is underlain by poor performing soils comprising interbedded layers of soft compressible silts and loose liquefiable sands to over 20m depth. The site is typical for Christchurch with a shallow groundwater table and artesian conditions. The site performed poorly during the 2010-2011 Canterbury Earthquake Sequence with extensive liquefaction, and associated ground damage. To provide a resilient and economical foundation system for this key development project, deep ground improvement comprising of a uniform grid of some 7,200 stone columns in conjunction with robust shallow foundations has been adopted. This paper discusses the geotechnical site constraints, and ground performance under earthquake loading and describes the various options considered for the development. The foundation option selected, the design considerations of the adopted stone column ground improvement, and foundation solution are described in detail, as well as, construction observations. The paper aims to provide insight into an urban large-scale ground improvement project for the engineering practitioner.

Nov 1, 2022

By Joanna Bzówka

Nowadays, there are some new requirements for the supermarket floors. The floors are loaded by high point- and moving-loads. In spite of this fact, it is necessary to ensure the stiffness of the floor and the stiffness of its support. When pile foundations are designed in the case of weak soil, the piles are recommended under the foundations of the supermarket and also under the floor layers. The example of foundation of a typical supermarket located on long­standing municipal dumping ground is presented. Indirect foundation - CFA piles, 0.5 m in diameter and 4.5 to 20.0 m long, was de­signed. Fifteen trial loading tests were carried out.

Jan 1, 2006

By Mark A. Rohrbach, Timothy R. Kovacs, PhD Saidin

"Crosshole Sonic Logging (CSL) testing is commonly used to verify the integrity, quality and ultimately the acceptability of the concrete in structural elements such as drilled shaft foundations, secant pile cutoff walls, and secant/tangent pile earth retention structures. Besides concrete quality, many factors can impact CSL test results (e.g. laitance, air temperature, access tube spacing, access tube debonding, etc.). Effective use of CSL testing requires fully informed qualified practitioners capable of distinguishing between abnormal readings unrelated to deficiencies in the drilled shaft concrete and similar readings indicating the presence or possible presence of drilled shaft defects. Based on data and experience gathered from CSL testing of thousands of drilled shafts across North America, this paper discusses such factors and other information useful when evaluating CSL test results, and provides practical recommendations intended to reduce the potential for incorrect test data interpretation. The CSL testing industry is lacking in a clear, universally accepted guideline for the interpretation of CSL data and acceptance criteria of these concrete elements. This paper proposes terminology and a streamlined process for use when atypical results are obtained. The proposed terminology and method are intended to simplify and expedite the submittal review and approval process. Because construction activities for these elements are often on the project’s critical path, the benefits obtained in terms of project savings and reducing costly delays areundoubtedly valuable.1. INTRODUCTIONCSL testing is used extensively throughout the world on many projects to verify the quality of concrete used for drilled shaft foundations, secant pile walls, diaphragm walls, etc. In this paper, these structural elements will be referred to as “drilled shafts,” as they are the most common subject of this test method. In the United States, CSL testing is frequently specified by state and regional transportation agencies, ports, design builders, and others. Although other methods are currently available such as Gamma-Gamma Logging and low-strain Impulse-Echo or Sonic-Echo testing, and new methods are under development such as the Thermal Integrity testing, CSL testing is likely to remain one of the most useful tools for evaluating the acceptability of constructed drilled shafts for quite some time. The popularity of CSL as a testing method can be attributed to two main factors: 1) there is no depth limitation to the method and 2) the apparent ease of interpreting the results. A third advantage of CSL testing is that, when correctly interpreted and with adequate test coverage, it is unlikely to misrepresent a defective profile resulting in acceptance of a defective or inadequate drilled shaft. In other words, CSL testing is very likely to underestimate concrete quality/drilled shaft acceptability within its area of coverage."

Jan 1, 2017

By S. Kanai

Nodular piles is to be piles provided with several nodular projections along the pile shaft, as shown in Fig. 1. Nodular piles are usually installed through either driving method with hammer or preboring method. This paper presents that the bearing capacity installed through each method is considerably higher than that of cylindrical pile without nodules. This paper also proposes the statistically analyzed unique formulae of the bearing capacity of nodular piles.

Jan 1, 1989

By Prof. Dr. -Ing. habil. Sascha Henke, Johannes Beck

The growth of Building Information Modeling (BIM) during recent years opens possibilities for integrating new digitally driven design approaches. While parametric design and algorithmic design slowly gains popularity in numerous ACE-applications, e.g. bridge design, it is rarely used by geotechnical professionals. This article presents an approach for implementation of parametric design in the BIM-based geotechnical design process. The methodology is applied to pile design and enables a real time design analysis according to DIN EN 1997-1 and EA-Pfähle 2012 considering boundary conditions such as pile position and layout, pile geometry, soil stratification and soil properties. By using intelligent attributes and scripts to control, calculate and assign them, the design analysis is directly executed in the BIM-software environment, in this case Autodesk Revit with Dynamo. This BIM integrated design approach allows multi-criteria evaluations of pile designs using aspects such as costs, environmental impact or constructability in addition to the commonly examined structural analysis criteria. As the proposed models are fully parametric, generative optimization algorithms can be applied to identify the ideal design for the entirety and each of the piles. Finally, the potential and limits of this methodology with respect to modeling, analysis, simulation and optimization are discussed.

May 1, 2022

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"Previous studies revealed that the helix deflection reduced the end bearing capacity of screw pile in dense ground even if the installation process is completed with minimal soil disturbance. The ultimate end bearing capacity in dense ground is difficult to achieve during the full-scale pile load test due to the limitation of the loading system. Therefore, in the present study, model scale of testing is selected to investigate the effect of helix deflection on load settlement behavior of single helix screw pile under increasing stress level. It is observed from the test results that the applied surcharge pressure, which is used to simulate the effect of stress level, is decreased with increase in model ground thickness. This decrease in the stress level is due to the frictional resistance between the container wall and sand. It is also observed that the end bearing capacity of screw pile increases with the increase in stress level but at gradually decreasing rate. The test results indicated that the helix deflection during the pile load test should not be more than critical deflection (0.72 mm average) of the helix to avoid any reduction in the end bearing capacity of screw pile. The helix deflection, which is measured after the pile load tests are also compared with the equations of flat circular plate having uniformly distributed load over the plate with simply supported and fixed inner edges.INTRODUCTIONThe screw pile consists of a central steel shaft with one or more helices attached at different location on the central shaft. The installation mechanism of screw pile consists of torque and pushing force. The screw pile installation mechanism can affect the unit weight of the ground during its installation. This effect is small in cohesive soils but it is quite noticeable in loose to medium dense sands (Adams 2011; Santos et al. 2013). The pushing force should be controlled in such a manner that pile penetration should be at least 80% of the pitch of the helix, during each revolution (Perko, 2009)."

Jan 1, 2017

By William M. Tanner, Daniel C. Brahana

"A drilled pier foundation was originally designed to support the proposed G. Wayne Clough Undergraduate Learning Commons on the campus of Georgia Tech in Atlanta, GA. Reflective of the site geology, the original drilled pier foundation was divided into a Northern and Southern portion with an allowable end bearing capacity of 60 ksf and 100 ksf, respectively. After initial pricing on the original design, several value engineering options were submitted that featured changes to the original design capacity and construction method. The project team selected the value engineering option that involved conducting an Osterberg Load Cell test to assess end bearing of the site bedrock and skin friction. Results of the Osterberg Load Cell test justified increasing the allowable end bearing capacity of the site bedrock to 100 ksf in the Northern portion and 125 ksf in the Southern portion. Considering the final foundation design and Osterberg Load Cell test program, a net savings of approximately $259,000, or approximately 34%, was obtained over the original design.Project BackgroundThe G. Wayne Clough Undergraduate Learning Commons (CULC) is a 5-story academic building on the Georgia Tech campus in Atlanta, Georgia. The CULC was completed in 2011 and consists of a concrete frame structure supported on a drilled pier foundation.After pricing of the original drilled pier foundation design, several value engineering (VE) analyses were performed by the foundation contractor in an effort to demonstrate the potential for a reduced foundation cost. The VE analyses focused on variations in design assumptions, as well as construction techniques. This paper presents a case study that demonstrates how the value engineering process can be used to reduce foundation costs.Site Investigation and Subsurface ConditionsThe CULC building site is located within the Southern Piedmont Physiographic Province, an area underlain by metamorphic and igneous rocks. McConnell and Abrams (1984) indicate that the site is located at the boundary between two distinct geologic formations. The Northern portion of the site is underlain by the Wahoo Creek Formation while the Southern portion of the site is underlain by the Stonewall Formation. The following paragraphs briefly describe the geotechnical investigations performed by the project geotechnical engineer (GE) for the CULC."

Jan 1, 2015

By Musbah A. Hasan, Ahmed M. Nasr, Fauzi Jarushi

Many transmission towers, high-rise buildings and bridges are supported by piles. These structures may be subjected to large lateral loads. Therefore, experimental investigations on model piles under lateral loads were conducted in uniform dry sand. Small-scale model tests were carried out considering the influence of pile length, pile diameter, sand density, roughness of pile surface and vertical load on the lateral resistance of a pile. Furthermore, the effect of pile load eccentricity (e/L) on the ultimate lateral resistance was studied. Investigations, of the influence of various parameters on the magnitude of the coefficient of subgrade reaction (nh), were also performed. It was found that the lateral load capacity of piles increases with increase in pile length, pile diameter, pile surface roughness and increase in the sand density. The results also showed that the coefficient of horizontal modulus of subgrade reaction, (nh), decreases with deflection increase. From the results, the coefficient of subgrade reaction for a smooth pile embedded in medium dense sand would decrease by (134%) when the lateral pile head deflection (yg) changes from (2% to 5%) of pile diameter.

Jan 1, 2017

By J. L. Goen

The Saint Joseph Hospital of Bellingham is located on a site underlain by glacial outwash. The construction of a five-story tower addition above an existing two-story wing was supported by five large trusses that impose a 1600 kips (7117 kN) column load on five pile caps in the courtyard of the hospital and on the new pile caps inside the existing MRI laboratory. The exterior columns of the trusses and the new parking garage addition were supported on conventional auger cast piles installed with conventional equipment. Helical Pulldown® micropiles were selected for use in the courtyard and the MRI laboratory because lightweight installation equipment (maximum unit weight of 7.5 kips (33.3 kN)) had to be used and it was required that no spoils be produced. The installation equipment was lifted into the courtyard by the jobsite crane. Sixty Helical Pulldown micropiles were installed for the pile caps in the courtyard. The pile caps inside the hospital were supported on 240 Helical Pulldown micropiles. Initial compression test indicated an allowable load for the micropiles to be 55 kips (244 kN). However, retest at a later date resulted in an increased allowed design load to be 85 kips (378kN) reducing the number of micropiles required by more than fifteen percent.

Jan 1, 2004

By Paul J. Axtell

Two new railroad bridges in Kansas City, Missouri are founded on drilled shafts embedded into the soil and underlying shale. The uncertainty arising from the non-homogeneous, anisotropic nature of most shales, and the variability of shales across the U.S., makes it a difficult material to assign appropriate design properties. As was the case on this project, the uncertainty of foundation performance in shale can lead to overly conservative designs, particularly with drilled shaft foundations. An extensive Statnamic axial testing program was performed to verify that the load-settlement behavior of the drilled shafts would be acceptable for the intended railroad traffic. Axial Statnamic testing was applied in three increasing cycles of 927 kips, 1007 kips, and 3177 kips, respectively. The maximum movements recorded at the shaft head during each of the loadings were 0.052 inches, 0.062 inches, and 0.257 inches, respectively. The loads applied in each of the respective Statnamic tests were not sufficient to reach the capacity of the shaft; so direct comparison of measured and calculated capacities is not possible. However, evaluation of the estimated design capacity can be accomplished based on results from the Statnamic testing program by utilizing normalized load transfer relations presented by O?Neill and Reese (1999). Such comparisons necessarily require extrapolation of the data measured in the Statnamic tests following typical load-displacement response. Results indicate the Kulhawy and Phoon (1993) method for estimating side resistance in Pleasanton shale rock sockets, assuming a smooth socket, appears to agree well with observed behavior during Statnamic testing. Accordingly, the O?Neill and Reese (1999) method for estimating the toe resistance in intermediate geomaterials, assuming cohesive rock with Rock Quality Designation (RQD) between 70 and 100, appears to agree well with observed behavior during Statnamic testing. Finally, based on Statnamic testing at varying load magnitudes and normalized curves developed by O?Neill and Reese (1999), the contribution of side resistance to the capacity of a deep foundation can be determined assuming no load is transferred to the base of the foundation during lower magnitude testing. Furthermore, higher magnitude testing can provide a means to evaluate the accuracy of design end bearing calculations.

Jan 1, 2006

By Bin Zhang

Drilled shafts are a popular type of foundation for transportation applications. They feature the advantages of providing high bearing capacity and generating low construction noise. Advancements in construction technology make it possible to construct drilled shaft with large diameters. In some transportation projects, the full structural loads are carried by a single large diameter drilled shaft; therefore accurately determining the bearing capacity of drilled shafts has important practical and safety implications. The increase of drilled shaft diameter combined with the structure properties of the surrounding soil play in an important role in their bearing capacity. The conventional methods for bearing capacity determination, which mostly come from experience with small diameter drilled shafts, may not work satisfactorily. This paper studies the influence of diameter on the bearing capacity of laterally loaded drilled shafts. Numerical simulations are conducted to investigate the effects of pile diameter on the lateral bearing capacity, especially the influence of shaft diameter and its structural contributions.

Jan 1, 2007

By A. Verghese Chummar

The paper presents a field study where the effect of negative drag caused the failure of a pile foundation system. Utilising the field observations the probable negative drag that acted on the piles is worked which gives an insight into the effect of negative drag on deep foundations.

Jan 1, 1996

By Dimitrios Polantzas P. E., Collin E. Sweeney E. I. T., Franklin M. Grynkiewicz P. E., Leili Javidanian P. E.

In the latest AASHTO design specifications, the Load and Resistance Factor Design (LRFD) method is prescribed for the design of retaining walls. However, inconsistencies arise when LRFD is used for retaining wall design versus the traditional Allowable Stress Design (ASD). Required toe embedment and wall loading demand vary greatly when the two design approaches are compared, all else being equal. This is due to application of linear load factors to properties that vary non-linearly in the design. These inherent inconsistencies are further intensified when introducing factors such as layered soil profiles, different wall types, groundwater elevation, and surcharge requirements. When applied correctly, these two design approaches, in theory, should lead the designer to the same result with little discrepancy, as they do with steel structure design. However, the use of the current AASHTO LRFD method for various geostructural retaining wall designs yields contradictory results that suggest existing retaining walls that have been successfully designed and constructed are unstable. Fundamentally, LRFD should be built on reliability-based calibrations; the successful past performance of existing retaining structures designed using ASD suggests that the LRFD approach requires considerable modification. The authors of this paper recommend that the current LRFD load factors be reviewed and revised based on more comprehensive wall performance data and wall type such that the difference between retaining structures designed using LRFD and those designed using ASD is eliminated.

Oct 1, 2022

By Amr M. Sallam

In recent years, with the increase of the number of high-rise buildings that are proposed and being built in Central Florida especially in Downtown Orlando, Augered Pressure Grouted Displacement (APGD) piles became a pronounced foundation option. The APGD pile is a bored displacement pile that does not result in drilling spoil. APGD piles are mostly suited for loose to medium granular soils and slightly silty/clayey sandy materials, such as those encountered in Central Florida. The case history presented in this paper involves the APGD piles recommended for a 35-story mixed-use condominium in Downtown Orlando. The subsoil condition was typical for the region; that is loose to medium fine sands underlain by thin layer of plastic sandy clays and plastic clays followed by mixed clayey sands and sandy clays with phosphates and traces of shells transitioned to the weathered limestone. Four APGD test piles were installed and were, statically, tested. Three of the tested piles failed to support the design load. Analysis of load test results showed that the bottom half of the test piles, below the plastic clay deposits, was not effective, which was attributed to structural deficiency resulted from possible pile necking due, in our opinion, to the increase of the porewater pressure within the plastic clays. Three additional test piles were constructed with modified reinforcement cage; that is to extend beyond the plastic clays with tighter stirrups. The additional test piles were, statnamically, tested and were able to sustain the design loads. The construction of the APGD piles through subsoil conditions similar to those of Downtown Orlando, where plastic clayey deposits are encountered, should account for the high porewater pressures that mostly will be developed within the plastic clay, hence, may cause pile necking. Extending the cage to penetrate through and pass the plastic clays reduced the necking potential and improved the test piles performance.

Jan 1, 2006

By David A. Staab

Numerical modeling was used to investigate the feasibility of using two geophysical imaging techniques, cross-borehole ground penetrating radar (XBGPR) tomography and electrical resistivity (ER) tomography, for detecting and characterizing defects in deep-mixed soil columns. XBGPR modeling was accomplished with a three-dimensional numerical forward modeling code and a two-dimensional inversion routine. Spatial variations in apparent dielectric constant (Ka) and attenuation (a) were mapped. Electrical resistivity modeling was accomplished with a three-dimensional numerical forward modeling code and a three-dimensional inversion routine. Spatial changes in electrical resistivity were then mapped. Three different types of defects were simulated, in addition to a defect-free column. The computer simulations suggest that XBGPR tomography and ER tomography might be useful, non-destructive methods for detecting and estimating the extent of defects in deep-mixed soil columns. The results show that small, isolated defects might be difficult to detect, but defects approximately equal to or larger than the sampling interval (for XBGPR) or vertical electrode spacing (for ERT) should be detectable.

Jan 1, 2004

By Jim Glider, Noah Miner

The Gordie Howe International Bridge is a project to build a cable-stayed bridge and border crossing across the Detroit River. With a span length of 2,800-ft (853.4 meters), the Gordie Howe International Bridge will have the longest main span of any cable-stayed bridge in North America. Each tower has two legs that are supported by six drilled shafts each for a total of 12. The tower shafts are 9.84 feet in diameter (3-m) and extend well into bedrock. 17 each, 6.6 feet (2-m) drilled shafts were built to support the aging river bulkhead and replace shipping bollards. In addition to shallow groundwater fed by the Detroit River, artesian conditions at depth result in a water head that is approximately 17.2-ft (5.2-m) above surface. At 95-ft (29-m) below grade Dundee Limestone, of the Detroit River Group, is moderately weathered and fracture density decreases with depth. The Dundee Limestone strength ranges from 8-ksi (55.1-MPa) to 12-ksi (82-MPa) and may carry hydrogen sulfide in fractures. Working through casing that sticks three stories out of the ground is less than ideal, but was necessary to maintain a positive fluid head and prevent artesian-related quality issues. The sheer scale of the bridge forces required a load test configuration that could impart an equivalent static load of over 38,000,000 pounds (170-MN). A suite of QA/QC tests was developed to ensure the shafts would meet the project plans and specifications to include critical base cleanliness criteria. Interesting CSL and TIP results obtained highlight the strengths and weaknesses of each test method. Cleaning drilling fluids with a centrifuge allowed recycling of product and reduced exposure to environmental contaminate exposure. Having large construction equipment working next to the river presented challenges in working pad design. A driven pile system was developed to support high oscillator forces and protect the aging seawall.

Sep 8, 2021

By Joseph A. Mann

"Soil mixing is a proven solution for the construction of ground improvement adjacent to sensitive structures due to the use of computer controlled and monitored equipment. The precision to which geometry is controlled can often be the deciding factor for selection of soil mixing versus other means of ground improvement. Protection of existing structures and utilities requires careful planning, investigation, and may demand supplemental control measures. During planning, it is imperative that the process be fully developed by the project team to ensure proper control measures are budgeted; otherwise, the success and safety of a project can be jeopardized.This paper discusses case histories of soil mixing performed in close proximity to large, sensitive, and critical utilities, including foundation support for an existing earthen dam impounding a water reservoir in upstate NY, a buffer zone for a tunnel drop shaft at an operating wastewater treatment plant in Washington DC, and a containment system to protect a major water line along an interstate widening project in Baltimore, MD. The function of soil mixing as ground improvement varied; however, the selection and application of the technique versus other means of ground improvement was specific due to the controlled manner of construction with soil mixing. Through the three case studies, small diameter (3- ft [0.9 m]), large diameter (8-ft [2.4 m]), and mass mixing applications will be discussed. Furthermore, the case studies offer insight into how the geotechnical community in the Mid-Atlantic utilizes soil mixing technology for widely varying applications. Additional topics of discussion will be the design and construction of the ground improvement systems, procedures and execution of the work to protect existing structures, and the QA/QC methods, procedures, and results from the projects.INTRODUCTIONWet soil mixing, also known as the Deep Mixing Method, is a ground improvement technique that improves the characteristics of weak soils by mechanically mixing them with cementitious binder slurry. To construct columns, a powerful drill advances a mixing tool with radial mixing paddles located near the bottom of the drill string. The binder slurry is pumped through the drill string to the tool as it advances and additional soil mixing is achieved as the tool is withdrawn.Wet soil mixing is applicable in a wide range of soils. Soil mixing has been performed at depths more than 100 lf (30 m). Soils vary widely in their ability to be mixed, depending on the soil type, strength, water content, plasticity, stratigraphy, and texture. Almost any soil type, including organics, can be treated with certain soil mixing technologies, although they may require high binder contents and/or pretreatment to achieve the required results. In cases when the target soil is very soft, including some very weak clays and peats, 100% of the soil may require treatment. This complete coverage of soil mixing is referred to as mass mixing."

Jan 1, 2015

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2000