Search Documents

By Raquel Franco de Souza Lima, Isao Matsuoka

"Microflotation studies and abstraction experiments were conducted with synthetic oxide spinels relating to chromite (MgCr2O4, FeCr2O4, FeFe2O4 and FeAl2O4), using sodium oleate as collector. An attempt was done to correlate this data with the speciation of oleate in the bulk solution and at the interface solid-water, to explain the floatability curves. The microflotation tests were conducted using a microflotation cell. The abstraction of sodium oleate was measured at 25°C, with one gram of synthetic spinel and the abstraction time was 30 minutes. After centrifuging, the residual oleate concentration in the supernatant was measured by using the spectrophotometric method described by Mizuniwa et al. (1977), that covers the range from 1.5 to 9 ppm. To cover the range from 0.2 to 1.5 ppm, the residual oleate concentration was measured using the spectrophotometric method described by Gregory (1966). The amount of oleate abstracted was calculated from the difference between initial and residual (equilibrium) concentrations.Figure 1 shows the floatability of FeCr2O4, FeAl2O4, FeFe2O4, MgCr2O4 as a function of pH and sodium oleate concentration of 1 x 10-5 M. The IEP of each sample is indicated in the figure by a vertical line in the horizontal axis. The chromium-bearing spinels FeCr2O4 and MgCr2O4 show the lowest isoelectric points (IEP), around pH 6, while in the case of FeFe2O4 and FeAl2O4, the isoelectric points lie at pH 6.5 and 7.3, respectively. It is seen that the flotation-pH curve for FeFe2O4 has a peak at the pH of the IEP, while flotation peak for FeCr2O4 appears at pH below the IEP and that of MgCr2O4 does at pH above the PZC. On the other hand, FeAl2O4 is floated at pH range between about 4 and 7,3 (IEP). This suggests that the pH value at which the maximum flotation occurs is dependent on the sort of spinel to be floated, though it appears in the vicinity of the respective IEP."

Jan 1, 2003

By N. Ahmed

"This paper is concerned with the drainage behaviour of gangue mineral in the froth phase. Experiments were carried out in a continuous laboratory flotation cell in which froth depth and bubble size can be changed independently. The fraction of solids returning from the froth to the pulp zone was expressed using a rate constant by considering the appropriate froth regimes. A mixture of hydrophilic solids (silica) and floatable particles (glass ballotini) was used as a flotation feed. Samples of glass ballotini of different hydrophobicities were obtained, using controlled silanation. Three samples, with contact angles of 50, 66, 82 degrees, were used. The effect of the initial bubble size (pulp bubble size), concentration of gangue mineral in the froth zone, and froth depth on the drainage of silica, were also investigated.Typical results obtained from this study is shown in the figure given below. In this figure drainage rate constant for the entrained solids in the presence of particles of the three hydrophobicities is plotted against froth height. As observed, the drainage rate of the entrained solids increases considerably with an increase in the degree of hydrophobicity. Concerning the effect of pulp bubble size on the drainage rate of entrained solids, larger bubbles always give higher drainage rates due to formation of relatively loose froth structures which allows gangue particles to easily move down to the pulp zone. Conversely, smaller bubbles exhibit lower drainage rate constants, in particular at shallow froth depths."

Jan 1, 2003

By Barbara Peszko, Tadeusz Tumidajski

"Various methods are used to identify the grain composition of fine-grained materials because so far the best notion of the grain size has not found and there is no single method to define grain size. In practice the most important are the following grain sizes: sieve diameter dt, effective diameter de, substitute diameter d2 and statistical diameter dst. The mentioned sizes are connected with the methods of analyses. Methods are correct but measure of different diameters of grain and their results are different.The most important methods of granulometric composition analyses are the following: the sieve analysis, the sedimentation method and the conductometric (Coulter-Counter) methods. In each of these methods various physical features connected with the grain size are measured.Sizes of grains defined by different formulas or measurement methods are associated mutually by dependencies, which are results of differences in their determination or calculation ways.In order to determine principles of results comparison the classification analysis results on linearly or non-linearly connected was made. Analyses which results demonstrate the same type of grain size distribution are treated as linearly connected. It is based on the general formulae which determines the probability density function of random variable which is the function of another random variable having the known density function.In order to show the difference in the grain composition of the same material qualified by different methods, three methods of investigations were distinguished. They are: the sieve analysis performed on precise sieves, the sedimentation analysis performed by means of a sedimentation balance “Sartorius” and the microscopic analysis performed after preparing a microscopic slide where the grain size was measured by the Martin’s method.The materials selected for the analysis were quartzite and glass, which are the material of high purity.The obtained results of mentioned above three types of analyses were approximated by distribution function of four distributions: Weibull, log-normal, cut Weibull and Gaudin-Schuhman."

Jan 1, 2003

By Andrzej Luszczkiewicz, Alicja Bakalarz

The application of new collectors is considered to improve the beneficiation of Polish sedimentary complex copper ores from the Legnica-Glogow Copper Basin (SW Poland), the upgradeability of which becomes more difficult because of ores grade declining. One group of potential collectors is represented by nonpolar reagents. According to the available literature data, only selected sulfides float in the presence of the nonpolar liquids. The paper presents laboratory scale flotation results for the main sulfide minerals occurring in the Polish copper ores applying either thiol (potassium ethyl xanthate) or nonpolar (aqueous emulsion of n-dodecane) collectors. The investigated feed contained 1.91 % Cu in the form of sulfide minerals such as bornite, chalcopyrite, chalcocite and covellite. Other sulfide minerals including galena, pyrite and sphalerite were also present in the samples. Several flotation tests with various doses of each collector were conducted. Mineralogical analyses of flotation products were carried out and the results compared. A comparison of the results indicated that all sulfide minerals floated well with high recoveries ranging from 91 % to 99 % in the presence of the thiol collector. The use of the nonpolar collector provided results in flotation of sulfide minerals with different terminal recoveries from 61 % for chalcopyrite to 100 % for sphalerite. The most significant differences in flotation in the presence of both types of collector under various conditions of upgrading were observed for chalcocite, chalcopyrite and covellite. Similar flotation results were observed for sphalerite and galena for both collectors. The studies confirmed selective flotation of sulfides from the copper sulfide ores of the Legnica-Glogow Copper Basin in the presence of nonpolar collectors.

Jan 1, 2014

By Hakan Gürsoy, Kemal Bilir, Bahri Öteyaka, Ali Uçar, Oktay Sahbaz

"Jet diffuser flotation column (JDFC) is a flotation device resembles Jameson flotation cell (JFC) in terms of operational principles, but it has significant difference structural points of view. This difference is an essential change in the downcomer to provide an increase of performance of the cell for the coarse particles. By using the hydrodynamic and fluid mechanics principles (Sahbaz et al., 2013) downcomer was changed as a diffuser, therefore turbulence at the end of the downcomer was reduced to provide better aggregate stability and homogeneous dissipation of the bubbles in the separation tank. According to experimental results carried out in pilot scale JDFC, not only higher flotation performance comparing with Jameson cell was obtained specifically for coarse talc particles in a certain condition, but also quiescent froth layer was acquired. In these tests, vertical pipe of JDFC having inlet diameter of 6 cm and outlet diameter of 11.5 cm was used with separation tank having the diameter of 39 cm. By using the data, pilot scale JDFC having 410 cm vertical pipe integrated with separation tank was produced and flotation tests were carried out by using the naturally hydrophobic mineral (talc). Finally, the talc recovery obtained as 94% by the use of JDFC, while Jameson cell has the recovery of 77% for the particle size of 250 µm."

Jan 1, 2014

By K. H. Luo, J. Y. Liu

An experimental study on interparticle breakage of three iron ores was carried out by compressive stressing of particle-bed in a piston-die device. The feeds to the particle-bed stressing were five narrow size fractions in the size range of 0.2~3.2 mm respectively and a wide size fraction of 0/4.0 mm. The pressures applied were in the range between 30 and 360 MPa. The results show that the energy absorption of the particle bed increases linearly with the pressure; the increase of the product fineness with the pressure declines as the pressure goes up; and the product size distributions resulting from interparticle breakage of different narrow size fractions have no self-similarity. Using data obtained from the piston-die compressive stressing test, the suitability of a previously-developed material-characterization model for interparticle breakage was verified for these ores. It is shown that the particle-bed compression test conducted with piston-die device in lab-scale may provide a cost-effective way of studying and modelling size-reduction of ore materials by interparticle breakage.

Jan 1, 2014

By Steven Wright, Sharif Jahanshahi, Shouyi Sun

"While there is a large industry based on recovering platinum group metals (PGM) from complex sulphide ores containing Cu and Ni, there is little information on the thermodynamics of the matte phase formed on smelting the ore and in particular the behaviour of Pt in the matte.The equilibrium between metallic platinum and industrial mattes was studied in a series of experiments where a small quantity of matte (5g) and platinum foil of 150 µm thickness (0.5 g) were equilibrated in magnesia crucibles at 1400°C under conditions where the oxygen and sulphur partial pressures were controlled.The chemistries of the phases were determined from EDS analysis using a scanning electron microscope. Line scans were initially used to confirm that the foils had attained a uniform composition across their thickness. The composition of the matte was determined from analysis of an area of matte including the small metallic droplets and dendrites.The distribution of Pt in Cu-Fe-Ni mattes (Pt: 1.5 – 3%) and solid Pt alloys (Pt: 54 – 72%) was studied. For a matte of base composition 45%Fe, 11%Ni, 8% Cu, at a base temperature 1400°C, the following behaviour was observed for the Pt distribution ratio:Under the range of sulphur and oxygen pressure of this study (log pO2 from -15 to –12.2, log pS2 from – 4.6 to –2.2), the distribution ratio of Pt between matte and alloy was independent of the sulphur and oxygen pressure, having a value of 0.04.The Pt distribution ratio increased from 0.02 to 0.08 with temperature from 1340 to 1450 oC.For mattes where the proportions of Cu and Ni were kept constant, a slight decreasing trend was shown for the distribution ratio of Pt versus the iron content (37 to 53%) in the matte but was not confirmed because of experimental uncertainty."

Jan 1, 2003

By Andrew D. McCallum, Russell A. Heins

"Until the advent of intensive cyanidation, gold gravity concentrates were generally treated by tabling. The table concentrates were smelted while table middlings and tailings were recycled to the milling circuit for further grinding and subsequent leaching in the CIP/CIL circuit. Gold recovery on production tables is relatively low, often only 30 percent, and rarely above 60 percent. Significant factors in tabling performance are; mineralogy and the operator’s experience and ability. Units have been developed by Gekko Systems to treat both batch and continuous gold concentrates. Unit sizes are determined by leach kinetics and the required residence time of the concentrate in the unit.Gekko commenced the commercialisation of intensive leaching of gravity gold concentrates in 1997 with the first commercial prototype of the InLine Leach Reactor (ILR). Over 20 units are now installed worldwide with half that number on the African continent. South African mines, South Deeps (Placer Dome WAJV) and Target (AvGold) have both installed InLine Leach Reactors. Ashanti Goldfields have placed the ILR on their standard equipment list and have six operating units with a seventh on order. AngloGold installed one of the first ILR production units at Morila in Mali.Gekko Systems successfully installed an ILR1000 Batch unit at the Antapite Mine in Peru in December 2002. The unit was installed to treat gravity concentrates and to replace a shaking table. Following installation, gravity gold recovery increased from 15% to 40% of total gold. The unit was operational from start up and the first gravity batch treated achieved 98% gold recovery. The gravity concentrates also have a high silver content and 95% recoveries on silver were also achieved.Preliminary testwork identified that the concentrates required additional oxygen to achieve peak performance. As a result of optimisation work in the laboratory, leach kinetics in the ILR have been excellent with only 6 hours residence required to achieve maximum gold extraction."

Jan 1, 2003

By Kobus (J. J. ) Rossouw, P. Chris Pistorius, Johannes Sono

"Different coal properties are important in SL/RN (coal-based rotary kiln) direct reduction of iron ore, and in electrical smelting of prereduced iron ore. Laboratory simulation was used to evaluate two candidate coals, which were similar in volatile content and rank, but differed in reactive maceral content. The tests served to evaluate both the reduction rate (during direct reduction) and the dissolution rate of carbon from the coal into an iron bath.Reduction rates of mixtures of magnetite and devolatilised coal were assessed isothermally, using samples of 55 grams. The off-gas analysis was used to follow the extent of reduction. Results are shown in Figure 1 a). Coal B was expected to be more reactive, based on its higher content of reactive macerals (77%, compared with 61% for Coal A). In line with this, Figure 1 a) does show a higher reduction rate with this coal. However, increasing the reduction temperature increases the reduction rate substantially,especially for the less-reactive Coal A.For the dissolution experiments, samples (mass: 250 g) were melted in an alumina crucible (under a nitrogen atmosphere), to give a starting composition around 1%C. When the desired temperature was reached, 25 g of char was added on top of the melt, through a feeding port. Results are shown in Figure 1 b). The more-reactive Coal B was less crystalline (the graphite crystallite size estimated from X-ray diffraction was 4.6Å, compared with 11.4Å for Coal A). This is associated with a lower dissolution rate in iron."

Jan 1, 2003

By Javier Baladron, Mijail Villar, Brandt Henriksson

"In this presentation an overview will be given of what has been observed by the authors in the copper concentration industry, with a large diversity of tailing thickeners operating under different conditions, although many of them are located in the same neighborhood. A closer look will be taken at the reported performance from different sites and from different thickener designs, either conventional or high rate, including those that were retrofitted, regardless of the thickener brand. An analysis is also made of the generic correlation of the size of the thickener and the performance in terms of solids loading (or unit area) and % solids. The paper envisions a technology development route, makes a brief analysis of the economic impact of the suggested route and points out the need for development in technologies around tailings thickeners, such as automation, yield stress measurement, slurry pumping and construction methods."

Jan 1, 2014

By A. Ekrem Yüce, Gülay Bulut, Feridun Boylu, Vecihi Gürkan, Istanbul Technical University, H. MustafaTarkan

"Nickel sulphide ores subjected to this investigation were taken from Orhaneli district where widespread chromite mineralisation can be occurred. Significant amounts of magnetite and chromite have been existed in the ore together with sulphide and oxide type nickel minerals. Ore sample is constituted about 70% magnetite, 15% sulphide minerals, 5% chromite and iron oxides as well as 10% gangue minerals.According to the chemical analysis results, the representative ore sample contains 1.32% Ni, 10.8% SiO2, 78.4% Fe2O3, 1.3 g/t Ag and 1.0 g/t Au. Mineralogical examinations showed that pentlandite (Fe, Ni)9S8, violarite (Ni, Fe)3S4, millerite NiS and asbolane (Co, Ni)MnO2.(OH)2.1-2H2O were the main nickel minerals and magnetite, chromite, chromium spinals, pyrite, pyrhotite, chalcopyrite, cubanite, goethite, hematite, limonite, rutile, chlorite, talc and serpentine group minerals as associated minerals.The aim of this investigation was to produce valuable nickel concentrates by using gravity separation, magnetic separation and flotation methods. As a results of laboratory scale studies, alternative flow sheets for the production of nickel sulphide concentrate were developed. The related experimental results are given in Table 1."

Jan 1, 2003

By Ricardo Duque-Soto, Gonzalo Montes-Atenas

The depletion of water resources has posed an enormous challenge to the continuity of many mine sites, particularly those located in arid zones worldwide. In Chile, the use of seawater has been foreseen as one possibility to solve this problem. Nevertheless, the direct use of high ionic strength solutions such as those present in the sea has been found to have some drawbacks. Specifically, rhe extraction of copper from complex ores using high ionic strength solutions such as that of seawater has become one of the most relevant topics in the field of copper hydrometallurgy. This study aims to determine the effect of the degree of salinity on copper extraction kinetics in mixed oxide-sulfide ores. A leach protocol was implemented to study the extraction kinetics, varying the degree of salinity of the medium and the temperature. A thermodynamic model was developed to explain differences in the metal extraction. It was found that the ionic strength impacted positively the copper extraction, probably due to the reduction of the effective concentration in solution due to ionic interactions enhancing the diffusive mass transport of copper ions. This effect is observed to be enhanced when up to an overall salinity values close to 20gpl.

Jan 1, 2014

By P. Saha, D. M. Chakrabarti, National Metallurgical Laboratory, P. Bhattacharyya, B. R. Sarkhel

The estimated reserve of the phosphatic soils at the Sukulu hills region of Uganda upto a depth of 60 meters is of the order of 200 million tonnes and analyses 10-12% P2O5. A 5-tonne sample of the phosphatic soil was received at the National Metallurgical Laboratory (NML), India for beneficiation studies. The ore occurred as a naturally degraded soil deposit and the slime contained earthy lateritic minerals which made it extremely sticky. Microscopic examination revealed the presence of limonite, magnetite (martitised), hematite and goethite as major minerals along with apatite and quartz. Presence of clay was indicated by earthy smell on moistening the sample. It was observed that getting rid of the slime was as important for adequate beneficiation of the ore, as it was difficult. Earlier studies on samples of the same ore at the NML and abroad established that it was necessary to pass the ore through a series of three stages of desliming, each consisting of a step of rigorous attrition scrubbing followed by hydrocycloning, for effective elimination of the sticky slimy coating which stubbornly adhered to mineral grains. Studies were carried out at the NML in two phases to develop a flowsheet for beneficiation of the phosphatic soil. In the first phase, reproducibility of the results obtained by employing a flowsheet developed abroad was confirmed along with suggesting some modifications of the flowsheet. Then 200 kg. of concentrate was produced following the recommended flowsheet for evaluation of its suitability for production of fertilisers. To remove the limonitic slimy coating, which stubbornly adheres to the other mineral grains, it was necessary to subject the ROM ore, after screening out the +840 micron size fraction which contained only 1.75% P2O5 , to three stages of hydrocycloning each preceded by attrition scrubbing. Then only conventional beneficiation techniques could be effectively employed to upgrade the ore.

Jan 1, 2003

By R. Peter King, Claudio L. Schneider, Reiner Neumann

Predicting the liberation spectra that is produced from breakage of two-phase ores under the random fracture assumption can be accomplished by measuring the conditional, on length, linear grade distribution directly from images obtained from a representative sample of the unbroken texture. The technique tremendously simplifies the prediction problem by avoiding the multiple convolutions that arise from the traditional method based on a description of texture from a measurement of the chord length distributions associated with each phase in the unbroken texture. For a 3-phase system, the phase transition probabilities associated with the textural information make the traditional calculation an almost insurmountable mathematical problem. The direct measurement procedure on the other hand can be expanded to three phases comparatively easily.

Jan 1, 2003

By Marina Nicolova, Irena Spasova, Plamen Georgiev, Stoyan Groudev

Different strains of "silicate" bacteria were used to improve the quality of kaolin by different ways of treatment. All strains formed large slimy capsules consisting of exopolysaccharides and were related to different species of the genus Bacillus, mainly to B. circulans and B. mucilaginosus. It was found that even a short contact of some hours of well developed cultures of these bacteria resulted in improvement of the bending strength and the other ceramic properties of the kaolin. The improvement was connected with the action of some secreted microbial metabolites such as soluble heteropolysccharides, monosugars and organic acids. The best results were achieved by continuous cultivation of bacteria in the presence of kaolin with a high relative humidity and subjected to periodic stirring.

Jan 1, 2014