Search Documents

By Y. F. Hou

This paper reports the results of the study of the influences of concentration and modulus of sodium potassium silicate solution (Na-K activator) and curing mode on the phase composition, mi-crostructure and strength development in the geopolymers prepared using Class F fly ash. X-ray dif-fraction (XRD), Fourier transform infrared spectroscopy (FTIR) and MAS NMR are utilized in this study. It shows that the compressive strength increases while sodium potassium silicate solution modulus increases, but when modulus exceeds 1.7, the compressive strength decreases, and it decreases markedly while modulus is greater than 2.0. The compressive strength improves with increase of sodium potassium silicate solution concentration. When the concentration is 36%, the compressive strength reaches the maximum. Elevated temperature can increase the strength of samples synthesized using sodium potassium silicate solution with 32% concentration and modulus 1.2. Compared to the strength of the sample cured at 50?, the strength of the samples cured at 65? and 80? are higher at 1 day and 3 days, but when cured at 80?, strength is smaller than that cured at 50? for 7 days. When temperature is too high, too long curing time will decrease the strength. Long precuring at room temperature before application of heat is beneficial for strength development, and there is about 10%~50% increase in strength of the samples cured at 1 day precuring and 2 days elevated temperature as compared to the strengths of the samples cured for 3 days at elevated temperature or cured for 28 days at room temperature. The main product of reaction in the geopolymeric material is amorphous alkali aluminosilicate gel.

Jan 1, 2014

By Peng Qian, Xiao Li, Guoyan Fu, Peiwei Han, Yongliang Wang, Shufeng Ye

"Arsenic removal from high arsenic gold concentrate is conducive to increase the mineral value and realize the mineral comprehensive utilization. This study investigated the alkaline pressure oxidation leaching (APOL) of an arsenical gold concentrate in lower temperature to separate the arsenic into filtrate. The effects of temperature, NaOH concentration, solid-liquid ratio, reaction pressure and stirring speed on the leaching efficiency were investigated, and the characteristics of the gold concentrate and leaching residues were evaluated using XRD and SEM analysis methods. The obtained results showed that by using lower temperature (<60?) it is possible to avoid the production of elemental sulfur during the leaching process, which is benefit for the oxidation of arsenopyrite; When the reaction was carried out under appropriate conditions, more than 98% of the arsenic will be extracted into the filtrate as the form of arsenate or thioarsenate. INTRODUCTION In recent years, there has been considerable interest in the recovery of gold from refractory arsenical gold ore. The arsenic in this kind of ore usually exists as the form of arsenopyrite, and the gold surrounded by arsenopyrite exists as the form of fine particles, which will give many difficulties to metallurgical work. When the content of arsenic in the gold ore is more than 0.5%, it will seriously penalize the smelting efficiency (Ruiz et al., 2014). So pretreatment of the refractory gold ore is necessary to obtain the largest economic value and environmental benefits (Balaz et al., 2000). The oxidation pretreatment processes mainly include roasting oxidation, pressure oxidation, chemical treatment and biological treatment (Ann et al., 1992; Kou and Chen, 2012; Tongamp et al., 2010; Fernandez et al., 1995; Lin and Zheng, 1996). Among them, the roasting oxidation and pressure oxidation are the more ordinary processes in industry. The roasting oxidation process is the mature and adaptable technology, but the production of waste gas containing sulfur and arsenic will pollute the environment. The pressure oxidation method possesses certain metallurgical and environmental advantages, and can efficiently decompose the mineral. According to the different solution media, the pretreatment can be divided into alkaline and acidic pressure leaching pretreatments (Papangelakis and Demopoulos, 1990; Hiskey and Sanchez, 1995). The acidic pressure oxidation method has been used in most smelting plants for high arsenic gold ore pretreatment, while the alkaline pressure oxidation is still not widely applied. Compared with the acidic pressure oxidation, the alkaline pressure oxidation can be realized under lower temperatures."

Jan 1, 2018

By Arman Ehsani, Ersin Yazici, Haci Deveci

The downstream treatment of chloride leach solutions of WPCB for recovery of base and precious metals by a combination of adsorption and precipitation processes were carried out. A synthetic leach solution (1 M HCl, 116.5 g/L Cl-, 30 g/L Cu2+, 2.5 g/L Fe3+, 5 mg/L Au3+, 10 mg/L Ag+ and 20 mg/L Pd2+), which was prepared based on the composition of the pregnant leach solution obtained in the previous study was used in the tests. The leach solution was initially subjected to activated carbon (AC) adsorption (20 g/L AC, 80°C) in which gold was selectively recovered over silver and palladium i.e., 88% Au recovery at 0.5 h (92% at 3.5 h) compared with only 3-6% for Ag/Pd. Copper and iron were also observed to adsorb on AC as indicated by 1.4% and 17% decline, in their respective concentrations. Following the adsorption and filtration stage, metallic copper was added into the gold-barren solution to allow reduction of Cu2+ to Cu+, and to cement Pd on metallic copper. Over the mixing period (1 h), 93% of the Pd was recovered while only 1.4% of silver was cemented onto metallic copper. Subsequently, the leach solution was gradually neutralised by NaOH to pH 4, 7.5 and 9.5 for the precipitation of copper as cuprite (Cu2O). It was found that 41% and 46% of Cu and Ag, respectively, were precipitated at pH 4 at which iron was almost totally (99.8%) removed from solution. Precipitation of copper and silver was increased further at high pHs. At pH 9.5, cumulative recoveries for copper and silver were 91% and 85%, respectively. XRD analysis of the precipitates confirmed the presence of cupric copper oxides/hydroxides and revealed that copper losses occurred at pH 4 was due to the undesired presence of cupric copper in the solution.

Jan 1, 2014

By P. Pourghahramani

Several structural characteristics change during intensive milling such as chemical composition, phase transformation, crystallite size, lattice strain, lattice parameter (s) and solid reactivity etc. The creation of defects enhances the stored energy (enthalpy) in the solids and consequently causes a decrease of activation barrier for the process and/or subsequent processes. In this paper, the effects of milling on the structural changes of hematite have been investigated using dry millings. The structural changes have been characterized using a combination analysis of BET surface area measurements and X-ray diffraction (XRD) analysis. Besides, the hydrogen reduction behaviors and kinetics of mechanically activated samples and initial sample were studied using simultaneous thermal analysis (STA). The methods of Williamson-Hall and Warren-Averbach were used for analyzing of XRD patterns to resolve and extract the microstructural characteristics of hematite phases. It was concluded that the breakage and aggregation of particles take place mainly in the starting and prolonged stages of dry grinding, respectively. The BET surface area enlarged steadily over the grinding processes whatever milling methods were utilized. The characterization of structural changes revealed that the hematite milled under various conditions did not undergo any significant reaction or phase transformation during milling processes. In addition, X-ray amorphous phase con-tent increased gradually with extending the grinding intensity. The maximum X-ray amorphous phase exceeds about 81% after 9 hours of milling in both tumbling mill and vibratory mill. The Williamson-Hall plots revealed the anisotropic character of line broadening for deformed hematite and changes in the trend of microstructural characteristics as a function of milling time. It was found that the surface weighted crystallite size decreases and lattice strain increases over the grinding periods. The minimum surface weighted crystallites were calculated about 17.3 nm, 12.2 nm for the products of tumbling and vibratory mills respectively. The maximum lattice strain,, in the grinding with tumbling and vibratory mills was calculated about 4.44×10-3 and 3.95×10-3respectively. 21/210nmLe=<> The non-isothermal kinetic analysis of the products revealed that Fe 2O3 reduced to Fe in a two-step process via Fe3O4. Intensive grinding resulted in improved resolution of overlapping reduction events. It was also established that the mechanical activation had a positive effect on the first step of reduction. The prereduction step in the activated samples initiated and completed at lower temperatures than that in non-activated samples. The activation energy of reduction decreased at the first step of reaction with increasing the grinding intensity. Intensive milling increased slightly the average activation energy of the second step of reduction due to the present of finely agglomerated particles and intensive sintering of the particles in higher temperature ranges.

Jan 1, 2014

By Harshad Bhagwat

The objective of this work is to investigate the inadequacies of current CFD based methodologies of model development for predicting combustion behavior of pulverized coal in furnaces. In the present paper, a steady state CFD model was used for in-depth analysis of pulverized coal combustion. The model accounts for turbulence, coal combustion, convective and radiative heat transfer and motion of coal particles. It also uses coal combustion models to account for important processes such as devolatilization, combustion of char and the evolution of fuel nitrogen during coal combustion. The model predicts fluid flow, heat transfer, progress of combustion and pollutant formation (NOx, etc.). The model uses several parameters, which need to be tuned with experimental data, which is not only limited in quantity but also insufficient in detail. Various existing methodologies like part calibration method for tuning of the parameters are discussed. In the present work, the parameters associated with coal combustion models were tuned and validated with published data obtained from an experimental furnace using one such part calibration methodology. The results clearly show that the model predictions differed with the experimental data not only quantitatively but also qualitatively. These discrepancies were attributed to part calibration methodology. A detailed parametric study was carried out to demonstrate the importance of parameters from various classes, namely, combustion kinetics, heat transfer, process and geometry parameters, and CFD model parameters. This investigation clearly indicates that parameters from different classes have significant effect on combustion behavior. The discrepancies in current methodology are discussed and a need for comprehensive methodology is highlighted. Keywords: pulverized coal combustion, computational fluid dynamics (CFD), pollutant formation (NOx), mathematical modeling

Sep 1, 2012

By Ela Mielczarski, Jerzy A. Mielczarski

"The adsorption of xanthate takes place at a different potential on each major sulfide mineral, hence, as it was demonstrated in the past, each mineral component can be selectively separated from ore under well controlled potential conditions. In real flotation this concept never works out for two reasons: the potential of single mineral particle results from complex surface reactions controlled by solution chemistry, and there is a galvanic interaction between different mineral particles present in the flotation pulp.In this study the formation of amyl xanthate hydrophobic products on pyrite, galena and chalcopyrite has been spectroscopically investigated in the presence of combinations of these minerals. The type of the adsorbed species and their amount were determined directly on mineral surfaces by infrared external reflection technique. Galvanic contact between grains of two different minerals has tremendous consequence on the adsorption of collector on both minerals. The detected changes are dramatic, from no adsorption to a coverage formation of a few monolayers. The results obtained indicate clearly that the observations and conclusions about the collector adsorption, hence also the surface hydrophobization, made for a single mineral system does not describe the real situation in a multi-component mineral system such as flotation pulp."

Jan 1, 2003

By M. N. Chandraprabha

Arsenopyrite is often associated with sulphides like pyrite, chalcopyrite and galena in refrac-tory gold ores. Selective flotation of arsenopyrite from associated sulphides is desirable for effective gold extraction when the gold is preferentially associated with the arsenopyrite matrix. By contrast, presence of arsenopyrite in flotation tailings poses a serious environmental threat due to arsenic dissolution. To prevent arsenic contamination from the mine wastes, it would be more economical and environmentally beneficial to remove this mineral during the froth flotation step. Use of Acidithiobacillus thiooxidans in the detoxification of arsenic containing sulphides is outlined in this pa-per. Biomodulation using Acidithiobacillus thiooxidans resulted in the preferential depression of pyrite from arsenopyrite. By suitable conditioning with cells and collector effective separation of arsenopyrite from pyrite was achieved. Biomodulation with wild cells did not yield separation of arsenopyrite from chalcopyrite. However, bacterial affinity could be induced to a desired sulfide mineral through environmentally controlled adaptation techniques. Through the use of arsenic-adapted bacterial cells, selective removal of arsenopyrite from chalcopyrite was readily achieved.

Jan 1, 2014

By Y. Q. He

The dynamic behaviors of the air bubbles in the dense gas-solid fluidized bed have a significant effect on the performance of dry coal separation. The combined method of experimental measurement and numerical simulation were conducted to conduct the research of the mean diameters and rising velocities of the bubbles in the fluidized bed. The calculation models of mean diameter and rising velocity of the single bubble were proposed. The results indicate that the models of the mean diameter raised by Rowe (1976) and the rising velocity raised in this work could be used to predict the bubble dynamic parameters in gas-solid fluidized bed. With the Geldart B type of magnetite powder as the medium solids and while the gas velocity of 1.5Umf=U=2.2Umf, the mean bubble diameter along the bed height is 36mm<Db<45mm, and the mean rising velocity of the single bubble is distributed in 40~65cm/s. The results of experimental measurement, numerical simulation and model predication provide well agreements finally. Based on the uniform fluctuations of air bubbles diameters and their rising velocities, the separation experiments of 50~6mm dry coal using the mixture of 0.3~0.15mm magnetite powder and <1mm fine coal as medium solids were carried out. The results show that the probable error, E is 0.06, which indicates a good separation performance by using the gas-solid fluidized bed. Keywords: dense gas-solid fluidized bed, bubble dynamic behaviors, numerical simulation, separation performance

Sep 1, 2012

By Trevor Saldanha, Stephen Grano

A key uncertainty in flotation modelling is determining, a priori, the proportion of each mineral which will develop a certain rate constant for different feeds of variable liberation and hydrophobicity. First and foremost is the ability to predict the proportion of minerals that will not be recovered, even at very long flotation times, and which therefore report to the tailing stream as the non-floatable fraction (i.e., having a zero rate constant). Recent empirical evidence has shown there are at least two factors which contribute to heterogeneity in flotation rates and, in particular, the appearance of a non-floatable fraction - heterogeneity in the distribution of adsorbed collector amount on a particle-by-particle basis, even for the same liberated mineral in the same size fraction, and the existence of a critical contact angle below which the bubble-particle union is unstable. In this paper, inferred measures of the critical contact angle for liberated particles are compared with stability model calculations. This has demonstrated that the dependency of the critical contact angle with particle size and mineral specific gravity are explicable by bubble-particle stability considerations. This argument is further extended to the flotation behaviour of composite particles, as a function of liberation class, in which the wetting perimeter of the attached bubble on the composite particle surface is constrained by the presence of a surrounding hydrophilic domain for the case of simple binary composites. Reasons for the different flotation behaviour of composite particles having different textures, as noted in the literature, are also discussed in terms of the stability of the bubble-particle union.

Jan 1, 2014

By Duong Huu Hoang, Nathalie Kupka, Urs A. Peuker, Martin Rudolph

"The froth ability, froth stability and the froth structure are strong influences in flotation process i.e. on water recovery, bubble size, entrainment of gangue particle, flotation rate constants, grade and recovery. The labscale flotation of rich apatite ore with a high mass pull leads to significant changes in pulp and froth properties over time. The froth stability decreases with increasing the flotation time. These changes can be related to different solid contents, reagent concentration, froth heights and bubble size distributions. This study presents the results from froth studies and discussions on the particle size of fully liberated silicates and degree of entrainment based on automated mineralogy size-by-size analysis. The change of entrainment in a rich apatite ore batch flotation with time will describe more precisely by measuring froth properties using a Dynamic Foam Analyzer. It is concluded that the degree of entrainment is not only dependent on particle size but also the pulp density due to its effect on particle settling and also froth properties in varying resistance to particle drainage. Furthermore, entrainment models are applied to predict the effect of size, flotation time on entrainmentINTRODUCTIONFroth flotation belongs to the group of heterocoagulation separation techniques. Froth flotation is classically divided into two active zones, the pulp zone (where particle collection occurs) and the froth zone. A schematics drawing of the interaction between both zones is plotted in Figure 18 (Yianatos and Contreras, 2010). In froth flotation, the collision probability in the collection zone is governed by the physics of the process or hydrodynamics (Wills and Finch, 2016). The true flotation event in the pulp occurs when the hydrophobic valuable mineral particles collide with bubbles and formation of a stable particle-bubble aggregates moving upwards against gravity to the froth phase (Yianatos et al., 2009)."

Jan 1, 2018

By S. H. Morar

Froth flotation is a physico-chemical separation process that takes place in two phases; pulp and froth phase. It is widely recognised as a complex process, due to the range of interactions present within the system. Of critical importance is the role of the froth phase within the system. The pulp kinetics governs the maximum potential recovery within a flotation cell, while the froth phase governs the selectivity via the froth?s stability. Higher froth stability improves recovery at the expense of grade, and lower froth stability improves selectivity. It is well known that the two major factors affecting froth stability are attached particles and solution chemistry. This paper looks at a flotation bank at different froth depth and frother concentrations. The air recovery to the concentrate is determined at each condition and relates the effect of the operating conditions on froth stability and transport to the amount of solids that are recovered to the froth and concentrate by true flotation. The results presented show that, for a given process objective, which in this case was a consistent mass pull profile, depending on the operating conditions, solids recovery in the pulp is affected by the air rate required to maintain the target mass pull. To a smaller extent, the changes in the pulp composition affect down-stream pulp recovery. The variation in solids recovered into the froth drives the froth stability at the start of the flotation bank, while the frother drives the froth stability at the end of the bank. The performance in between these two extreme conditions arises from an interaction of these two effects. The consequences of these interactions can give rise to counter-intuitive responses that can confound efforts to optimise the performance of the bank.

Jan 1, 2014

Considerable attention has been, and is being, given to the physics of water-films associated with bubble interactions at surfaces. In contrast, little information on the chemistry of such films has been reported. This communication reports a method using sum frequency vibrational spectroscopy (SFVS) to describe hydrogen bonding of interfacial water molecules in water films created with bubbles at hydrophilic and hydrophobic surfaces. The SFVS spectra of water films at hydrophilic silica surfaces differ significantly from the spectra of water at a hydrophobic silica surface. The SFVS spectra indicate that a very ordered water structure exists in water films at the hydrophilic silica surface during contact with a bubble and that the extent of hydrogen bonding increases with an increase in contact pressure. Such structural considerations as well as repulsive electrostatic and Van der Waals forces account for film stability for a bubble at the hydrophilic silica surface. In contrast, the SFVS spectra of water at a hydrophobic silica surface show a lack of hydrogen bonding and are characterized by a distinct absorption at about 3700 cm-1 similar to the spectrum of the air/water interface. These results suggest the presence of a water void, or water exclusion zone, at the hydrophobic surface, as supported by X-ray reflectivity measurements reported in the literature, by atomic force microscopy, and by the results from molecular dynamics simulations. Of course the water film at the hydrophobic surface is unstable with film thinning and rupture upon bubble contact. Under these circumstances it is shown that an attractive Van der Waals force between the bubble and the hydrophobic surface can be expected when the water exclusion zone is taken into consideration. As the thickness of the water exclusion zone increases to a thickness corresponding to the size of nano bubbles, the calculated attractive Van der Waals force increases. This analysis may help to explain the so-called ?short range? and ?long range? hydrophobic forces. Keywords: SFVS spectra, hydrophilic silica surface, hydrophobic silica surface

Sep 1, 2012

By V. I. Ryaboy, I. V. Ryaboy, E. D. Shepeta

"The problem of separation of copper minerals and arsenopyrite remains relevant because of environmental requirements. The selective action of reagents with the thioamide group (thioamides) is known in iron sulfide’s flotation of pyrite and pyrrhotite. The aim of this study was to reduce the arsenic content in the copper concentrate when using thioamides by reducing the flotation of arsenopyrite in the flotation of the sulfide part of the skarn scheelite-sulfide ores. We have chosen the most widely used thioamides for the study, such as Z-200. We also synthesized new reagents with the thioamide group. The most selective and the most powerful thioamide copper collector were used for further studies. Reduction of arsenic content in copper concentrates is achieved in the following way: You need to apply a strong thioamide collector with a selective but weak dialkyldithiophosphate collector, or vice-versa, a selective, but a weak thioamide collector should be used with the dialkyldithiophosphate reagent with strong collective properties. The proposed combination presents industrial interest because of its accessibility. The application of thioamides in copper minerals and arsenopyrite selection has showed that these reagents have fewer selective properties than dialkyldithiophosphates. To achieve the comparable recovery of copper using dialkyldithiophosphates requires markedly greater consumption of thioamides, due to their lower hydrophobic ability. The application of a composition of thioamides and dialkyldithiophosphates allows to increase the recovery of copper and to obtain a lower arsenic content in copper concentrates compared to their individual use. The lowest arsenic content in the copper concentrate is obtained in the composition consisting of the newly synthesized thioamide with strong collective properties and selective dialkyldithiophosphate. The addition of even small amounts of xanthate to the composition of thioamides and dialkyldithiophosphates causes a sharp increase in the arsenic content in the copper concentrate without a notable increase in copper recovery."

Jan 1, 2018

By B. Q. By

TiO2 is an ideal material for catalytic technology due to its unique properties. In this paper, Sm3+ doped TiO2 photo-catalyst was developed to improve the efficiency of TiO2 and to use the natural light as irradiation source, which was made from Titanium Tetrabutoxide and Samarium Oxide with the Sol-Gel process. The Sm3+-TiO2 photocatalyst was used to degrade reactive orange 4 (RO4) in Azo Dyes. The effects of solution pH, Sm3+ concentration and catalytic time on the degradation rate of RO4 were studied. The characteristics of the catalyst were analyzed with XRD and TEM. The experimental results show that the catalyst has high activity in the degradation of RO4. The Azo bonds of RO4 are active and easily broken by oxidation. The catalytic activity of the Sm3+ doped catalyst greatly depends on the pH of solution. The catalyst has high photo-catalytic activity at both neutral and alkaline conditions. The degradation mechanism of the Sm3+ doped TiO2 photo-catalyst was also discussed.

Jan 1, 2014

By M. Kinnunen

Handling of municipal solid waste (MSW) and control of its potential resources is becoming increasingly important in modern society. The OECD (Organization for Economic Co-operation and Development) average on municipal waste produced in 2003 was that of around 570 kg per inhabitant. In European Union countries around half amount is of MSW landfilled. In Finland still 88% of MSW was landfilled in 2004. Since incineration reduces MSW volume significantly while producing heat energy, it has become one of the most common waste handling techniques. The shortcoming of incineration is however, that incinerated MSW is often not pre-sorted and it produces slags and ashes as side streams from which recovery of metals is difficult. This paper looks into possibilities of scrap metal recovery for recycling from municipal solid waste incineration (MSWI) bottom ash. In order to do that, a flow sheet of physical separation methods was developed and tested with Finnish rotary furnace MSWI bottom ash. In addition, an empirical model for estimation of the recoveries of scrap metals with physical separation methods for treatment of MSWI bottom ash was developed. According to the results of this study, for 1 Mt of incinerated MSW with 30% mass reduction, a minimum resource potential of 100 kt for magnetic metal scrap of roughly 24 % grade and about 19 kt of non-magnetic metal scrap of roughly 65 % grade. In other words, 57 kg magnetic scrap and 12 kg non-magnetic scrap per inhabitant at the mentioned grades, respectively. Although wide variations of parameters affect the MSWI bottom ash quality, it can be said that a considerable amount of metals is drained into MSWI bottom ash. Results of this study show that from MSWI bottom ash significant material streams metal scrap can be reintroduced into the resource cycle which would otherwise be lost.

Jan 1, 2014

By M. Kalicinski, M. Lyssyy

"Access to information is a key component for making improvements to any process. This is particularly true for all aspects of the iron mining and steelmaking process. The ability to make rapid control decisions can significantly influence process outcomes, including ensuring product specification, mining quality, transportation limits, upgrade factors, waste bypass and direct shipping, among many others. While traditional laboratory methods provide feedback for such processes, having access to analysis results in real-time can lead to positive reactive and predictive control decisions to be made rapidly, leading to significant improvements throughout the process. Scantech has been designing, manufacturing and supplying technological products to the minerals industry since 2002 to enable the availability of such real-time information to a mine or plant, with the benefits being enjoyed by a wide range of operators. This paper provides a summary of the available technologies used in the iron ore and steel industries, as well as providing case studies of their use in African and Australian iron ore and European steel, as well as a description of the potential benefits of a range of analysis equipment.INTRODUCTION Access to information is critical for any process, and is a fundamental component for making process control decisions. In order to yield effective processing outcomes, it is important for that information to be readily available, preferably as quickly as possible, and to be as accurate as possible. While speed and accuracy are often traded off against each other, there are numerous technologies available in a processing environment that allow for both rapid flow of information and a high level of accuracy. The use of on-belt analysis equipment has a long trusted history of use in a number of mining and processing environments and industries, providing information such as elemental composition and grade of conveyed materials, moisture content, waste proportion and energy information. Australian company Scantech has been a provider of such equipment since 1981, and has become an industry leader in both the supply and development of on-belt analysers across a range of industries."

Jan 1, 2018

Sedimentary deposits such as sandstone are formed by the aggregation of cemented sand grains. Phosphates and laterite present similar aggregation of mineral grains. Grains and cement have different mineralogy and chemical characteristics. During size reduction through crushing or coarse grinding, the rocks are crumbled. Mineral grains and cement are then liberated, and the produced size distribution reflects their ?natural size distribution?. Mathematical modelling of these concomitant effects of crumbling and mineral liberation necessitates a specific material description and the adaptation of the commonly used theories of breakage kinetics and population balance. The coarse particles are mainly agglomerates made of mineral grains and cement particles whereas the fine particles are grains and cement with a natural grain size distribution. The population balance between the different particle size and particle types during size reduction takes into account the breakage rate and the progeny size distribution. The breakage rate can be described by a simple probability function or by a first order kinetics whereas the progeny size distribution is described by a breakage matrix. The model proposed here considers that the agglomerates will produce other agglomerated particles, liberated grains and cement particles; the two latter having their natural size distribution. The liberated grains and cement particles are subject to size reduction and follow the most commonly used theory of breakage. The present paper describes the theoretical approach of the concomitant crumbling and liberation effects. The application to a mathematical model for the cone crusher is presented. The advantage of such approach is then demonstrated through a simulation study for the optimisation of a crushing plant. Keywords: mineral liberation, modelling, crushing, sedimentary ore

Sep 1, 2012

By X. P. Guo

In this paper the test results of flotation of the kyanite ore from a Chinese mine are described. The objective of this work is to determine effective recovery process to obtain kyanite concentrate with high quality and high recovery for a new concentrator design. The valuable minerals of the ore are kyanite, garnet and magnetite, contents of them are 14.0%, 5.9% and 1.2%, respectively. The gangue minerals are mainly biotite, feldspar and quartz, contents of them are 33.8%, 17.8% and 25.6%, respectively. The kyanite in the ore contains a little iron. In laboratory flotation tests the factors affecting the flotation such as slime, alkalinity of pulp, and flowsheet configuration are studied. The interference of biotite on kyanite flotation as well as selective flotation of garnet is examined. On the basis of above-mentioned results the flowsheet of ore treatment comprising de-sliming, mica flotation, low intensity magnetic separation of magnetite, high intensity magnetic separation of garnet and coarse biotite as well as flotation of kyanite is pre-sented for comprehensive recovery of kyanite, garnet and magnetite. The kyanite concentrate con-taining more than 59% Al2O3 is obtained with a kyanite recovery of 70.0%. The contents of Fe2O3and biotite in kyanite concentrate decreased from 2.02% and 5% to 1.30% and 1%, respectively. The disadvantage of low kyanite grade in raw ore is compensated by accessory recovery of garnet and magnetite in the ore.

Jan 1, 2014

By Y. P. Lu

PET/kaolin nanocomposites were prepared with melt blending and the structure of the composites was characterized through IR techniques. The results showed that there is stable chemical bonding between PET and kaolin. In addition, the dispersion condition of nanokaolin was observed by means of SEM and TEM. As a result, the thickness of the dispersed nanokaolin particles in PET matrix is mainly from 20mm to 200nm, and the nanosized particles congregate to some extent in the samples. In addition, it was found the kaolin particles almost homogeneously dispersed in the PET matrix, without preferential orientation because of the shear effect due to melt blending. Furthermore, the mechanical properties of PET/kaolin nanocomposites are dependent on the modification efficiency of nanokaolin. With the poor efficiency, the nanokaolin particles tend to aggregate at a high content and have a bad interfacial compability between nanokaolin and PET matrix, which lead to stress concentration, so the mechanical property descends. Experiments of different contents of modified nanokalin indicated that the intensity of PET/kaolin nanocomposites decreased firstly, then increased, and then decreased, with the nanokaolin content of 4 to 5 percent, the rupture stress of the composites showed a maximum value, which was higher than that of pure PET. On one hand, nanokaolin decreases the function among PET macromolecules, which will decline the mechanical properties, on the other hand, the piece structure of kaolinite improves the intensity of the nanocomposite. When the nanokaolin content is low, the former has the dominant effect on mechanical property, while the latter will play a leading role with the content increasing. But if the nanokaolin content still increases, the agglomeration and stress concentration will be obvious.

Jan 1, 2014

By F. Göktepe

Flotation gases and conditioning of the pulp with them are one of the important parameters of flotation and should be taken into account especially in the flotation of sulphide ores. In this study, flotation of pure chalcopyrite and pyrite samples were investigated with air, oxygen and nitrogen as flotation gas and the effect of conditioning with these three gases also were performed. Flotation gas was introduced for 5min, 10min, 15min and 20 min. For chalcopyrite flotation there was no drastic change in recovery when air, oxygen and nitrogen were used as flotation gas but conditioning the pulp with oxygen for 10 minutes increased the recovery about 8% where pulp potential has been approximately 25 mV with chalcopyrite and 150 mV with platinum electrodes. Conditioning with all three gases decreased the pyrite recovery by about 20% with 20 minutes conditioning. Pulp potential decreased in the presence of nitrogen while conditioning with air and oxygen increased the pulp potential for both electrodes. Generally potential increased for both minerals with oxygenation and aeration time but it was stable or slightly decreased with nitrogenation. Comparison of the gases showed that the different flotation gases do not effect flotation recovery but conditioning the pulp with these gases at pre-flotation effects chalcopyrite and pyrite flotation recovery, most dramatically pyrite.

Jan 1, 2014